These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
config TARGET_ATC
bool "Support atc"
-config TARGET_CPU86
- bool "Support CPU86"
-
-config TARGET_CPU87
- bool "Support CPU87"
-
config TARGET_KM82XX
bool "Support km82xx"
endchoice
source "board/atc/Kconfig"
-source "board/cpu86/Kconfig"
-source "board/cpu87/Kconfig"
source "board/keymile/km82xx/Kconfig"
endmenu
+++ /dev/null
-if TARGET_CPU86
-
-config SYS_BOARD
- default "cpu86"
-
-config SYS_CONFIG_NAME
- default "CPU86"
-
-endif
+++ /dev/null
-CPU86 BOARD
-M: Wolfgang Denk <wd@denx.de>
-S: Maintained
-F: board/cpu86/
-F: include/configs/CPU86.h
-F: configs/CPU86_defconfig
-F: configs/CPU86_ROMBOOT_defconfig
+++ /dev/null
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = cpu86.o flash.o
+++ /dev/null
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ioports.h>
-#include <mpc8260.h>
-#include "cpu86.h"
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-
-const iop_conf_t iop_conf_tab[4][32] = {
-
- /* Port A configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PA31 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII COL */
- /* PA30 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII CRS */
- /* PA29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 MII TX_ER */
- /* PA28 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 MII TX_EN */
- /* PA27 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII RX_DV */
- /* PA26 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII RX_ER */
- /* PA25 */ { 1, 0, 0, 1, 0, 0 }, /* FCC2 MII MDIO */
- /* PA24 */ { 1, 0, 0, 1, 0, 0 }, /* FCC2 MII MDC */
- /* PA23 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 MII MDIO */
- /* PA22 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 MII MDC */
- /* PA21 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[3] */
- /* PA20 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[2] */
- /* PA19 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[1] */
- /* PA18 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[0] */
- /* PA17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[0] */
- /* PA16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[1] */
- /* PA15 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[2] */
- /* PA14 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[3] */
- /* PA13 */ { 1, 0, 0, 1, 0, 0 }, /* FCC2 MII TXSL1 */
- /* PA12 */ { 1, 0, 0, 1, 0, 1 }, /* FCC2 MII TXSL0 */
- /* PA11 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 MII TXSL1 */
- /* PA10 */ { 1, 0, 0, 1, 0, 1 }, /* FCC1 MII TXSL0 */
- /* PA9 */ { 0, 1, 0, 1, 0, 0 }, /* SMC2 TXD */
- /* PA8 */ { 0, 1, 0, 0, 0, 0 }, /* SMC2 RXD */
- /* PA7 */ { 0, 0, 0, 0, 0, 0 }, /* PA7 */
- /* PA6 */ { 1, 0, 0, 1, 0, 1 }, /* FCC2 MII PAUSE */
- /* PA5 */ { 1, 0, 0, 1, 0, 1 }, /* FCC1 MII PAUSE */
- /* PA4 */ { 1, 0, 0, 1, 0, 0 }, /* FCC2 MII PWRDN */
- /* PA3 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 MII PWRDN */
- /* PA2 */ { 0, 0, 0, 0, 0, 0 }, /* PA2 */
- /* PA1 */ { 1, 0, 0, 0, 0, 0 }, /* FCC2 MII MDINT */
- /* PA0 */ { 1, 0, 0, 1, 0, 0 } /* FCC1 MII MDINT */
- },
-
- /* Port B configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
- /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
- /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
- /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
- /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
- /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
- /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
- /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
- /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
- /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
- /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
- /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
- /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
- /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
- /* PB17 */ { 0, 0, 0, 0, 0, 0 }, /* PB17 */
- /* PB16 */ { 0, 0, 0, 0, 0, 0 }, /* PB16 */
- /* PB15 */ { 0, 0, 0, 0, 0, 0 }, /* PB15 */
- /* PB14 */ { 0, 0, 0, 0, 0, 0 }, /* PB14 */
- /* PB13 */ { 0, 0, 0, 0, 0, 0 }, /* PB13 */
- /* PB12 */ { 0, 0, 0, 0, 0, 0 }, /* PB12 */
- /* PB11 */ { 0, 0, 0, 0, 0, 0 }, /* PB11 */
- /* PB10 */ { 0, 0, 0, 0, 0, 0 }, /* PB10 */
- /* PB9 */ { 0, 0, 0, 0, 0, 0 }, /* PB9 */
- /* PB8 */ { 0, 0, 0, 0, 0, 0 }, /* PB8 */
- /* PB7 */ { 0, 0, 0, 0, 0, 0 }, /* PB7 */
- /* PB6 */ { 0, 0, 0, 0, 0, 0 }, /* PB6 */
- /* PB5 */ { 0, 0, 0, 0, 0, 0 }, /* PB5 */
- /* PB4 */ { 0, 0, 0, 0, 0, 0 }, /* PB4 */
- /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* PB3 */
- /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* PB2 */
- /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* PB1 */
- /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* PB0 */
- },
-
- /* Port C */
- { /* conf ppar psor pdir podr pdat */
- /* PC31 */ { 0, 0, 0, 0, 0, 0 }, /* PC31 */
- /* PC30 */ { 0, 0, 0, 0, 0, 0 }, /* PC30 */
- /* PC29 */ { 1, 0, 0, 0, 0, 0 }, /* SCC1 CTS */
- /* PC28 */ { 1, 0, 0, 0, 0, 0 }, /* SCC2 CTS */
- /* PC27 */ { 0, 0, 0, 0, 0, 0 }, /* PC27 */
- /* PC26 */ { 0, 0, 0, 0, 0, 0 }, /* PC26 */
- /* PC25 */ { 0, 0, 0, 0, 0, 0 }, /* PC25 */
- /* PC24 */ { 0, 0, 0, 0, 0, 0 }, /* PC24 */
- /* PC23 */ { 0, 0, 0, 0, 0, 0 }, /* FDC37C78 DACFD */
- /* PC22 */ { 0, 0, 0, 0, 0, 0 }, /* FDC37C78 DNFD */
- /* PC21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RX_CLK */
- /* PC20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII TX_CLK */
- /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK */
- /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII TX_CLK */
- /* PC17 */ { 0, 0, 0, 0, 0, 0 }, /* PC17 */
- /* PC16 */ { 0, 0, 0, 0, 0, 0 }, /* PC16 */
- /* PC15 */ { 0, 0, 0, 0, 0, 0 }, /* PC15 */
- /* PC14 */ { 0, 0, 0, 0, 0, 0 }, /* PC14 */
- /* PC13 */ { 0, 0, 0, 0, 0, 0 }, /* PC13 */
- /* PC12 */ { 0, 0, 0, 0, 0, 0 }, /* PC12 */
- /* PC11 */ { 0, 0, 0, 0, 0, 0 }, /* PC11 */
- /* PC10 */ { 0, 0, 0, 0, 0, 0 }, /* PC10 */
- /* PC9 */ { 0, 0, 0, 0, 0, 0 }, /* FC9 */
- /* PC8 */ { 0, 0, 0, 0, 0, 0 }, /* PC8 */
- /* PC7 */ { 0, 0, 0, 0, 0, 0 }, /* PC7 */
- /* PC6 */ { 0, 0, 0, 0, 0, 0 }, /* PC6 */
- /* PC5 */ { 0, 0, 0, 0, 0, 0 }, /* PC5 */
- /* PC4 */ { 0, 0, 0, 0, 0, 0 }, /* PC4 */
- /* PC3 */ { 0, 0, 0, 0, 0, 0 }, /* PC3 */
- /* PC2 */ { 0, 0, 0, 0, 0, 0 }, /* PC2 */
- /* PC1 */ { 0, 0, 0, 0, 0, 0 }, /* PC1 */
- /* PC0 */ { 0, 0, 0, 0, 0, 0 }, /* FDC37C78 DRQFD */
- },
-
- /* Port D */
- { /* conf ppar psor pdir podr pdat */
- /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 RXD */
- /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 TXD */
- /* PD29 */ { 1, 0, 0, 1, 0, 0 }, /* SCC1 RTS */
- /* PD28 */ { 1, 1, 0, 0, 0, 0 }, /* SCC2 RXD */
- /* PD27 */ { 1, 1, 0, 1, 0, 0 }, /* SCC2 TXD */
- /* PD26 */ { 1, 0, 0, 1, 0, 0 }, /* SCC2 RTS */
- /* PD25 */ { 0, 0, 0, 0, 0, 0 }, /* PD25 */
- /* PD24 */ { 0, 0, 0, 0, 0, 0 }, /* PD24 */
- /* PD23 */ { 0, 0, 0, 0, 0, 0 }, /* PD23 */
- /* PD22 */ { 0, 0, 0, 0, 0, 0 }, /* PD22 */
- /* PD21 */ { 0, 0, 0, 0, 0, 0 }, /* PD21 */
- /* PD20 */ { 0, 0, 0, 0, 0, 0 }, /* PD20 */
- /* PD19 */ { 0, 0, 0, 0, 0, 0 }, /* PD19 */
- /* PD18 */ { 0, 0, 0, 0, 0, 0 }, /* PD18 */
- /* PD17 */ { 0, 0, 0, 0, 0, 0 }, /* PD17 */
- /* PD16 */ { 0, 0, 0, 0, 0, 0 }, /* PD16 */
-#if defined(CONFIG_SYS_I2C_SOFT)
- /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SDA */
- /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SCL */
-#else
-#if defined(CONFIG_HARD_I2C)
- /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */
- /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */
-#else /* normal I/O port pins */
- /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */
- /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */
-#endif
-#endif
- /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
- /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
- /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
- /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
- /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TXD */
- /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RXD */
- /* PD7 */ { 0, 0, 0, 0, 0, 0 }, /* PD7 */
- /* PD6 */ { 0, 0, 0, 0, 0, 0 }, /* PD6 */
- /* PD5 */ { 0, 0, 0, 0, 0, 0 }, /* PD5 */
- /* PD4 */ { 0, 0, 0, 0, 0, 0 }, /* PD4 */
- /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* PD3 */
- /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* PD2 */
- /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* PD1 */
- /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* PD0 */
- }
-};
-
-/* ------------------------------------------------------------------------- */
-
-/* Check Board Identity:
- */
-int checkboard (void)
-{
- printf ("Board: CPU86 (Rev %02x)\n", CPU86_REV);
- return 0;
-}
-
-/* ------------------------------------------------------------------------- */
-
-/* Try SDRAM initialization with P/LSDMR=sdmr and ORx=orx
- *
- * This routine performs standard 8260 initialization sequence
- * and calculates the available memory size. It may be called
- * several times to try different SDRAM configurations on both
- * 60x and local buses.
- */
-static long int try_init (volatile memctl8260_t * memctl, ulong sdmr,
- ulong orx, volatile uchar * base)
-{
- volatile uchar c = 0xff;
- volatile uint *sdmr_ptr;
- volatile uint *orx_ptr;
- ulong maxsize, size;
- int i;
-
- /* We must be able to test a location outsize the maximum legal size
- * to find out THAT we are outside; but this address still has to be
- * mapped by the controller. That means, that the initial mapping has
- * to be (at least) twice as large as the maximum expected size.
- */
- maxsize = (1 + (~orx | 0x7fff)) / 2;
-
- /* Since CONFIG_SYS_SDRAM_BASE is always 0 (??), we assume that
- * we are configuring CS1 if base != 0
- */
- sdmr_ptr = &memctl->memc_psdmr;
- orx_ptr = &memctl->memc_or2;
-
- *orx_ptr = orx;
-
- /*
- * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
- *
- * "At system reset, initialization software must set up the
- * programmable parameters in the memory controller banks registers
- * (ORx, BRx, P/LSDMR). After all memory parameters are configured,
- * system software should execute the following initialization sequence
- * for each SDRAM device.
- *
- * 1. Issue a PRECHARGE-ALL-BANKS command
- * 2. Issue eight CBR REFRESH commands
- * 3. Issue a MODE-SET command to initialize the mode register
- *
- * The initial commands are executed by setting P/LSDMR[OP] and
- * accessing the SDRAM with a single-byte transaction."
- *
- * The appropriate BRx/ORx registers have already been set when we
- * get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE.
- */
-
- *sdmr_ptr = sdmr | PSDMR_OP_PREA;
- *base = c;
-
- *sdmr_ptr = sdmr | PSDMR_OP_CBRR;
- for (i = 0; i < 8; i++)
- *base = c;
-
- *sdmr_ptr = sdmr | PSDMR_OP_MRW;
- *(base + CONFIG_SYS_MRS_OFFS) = c; /* setting MR on address lines */
-
- *sdmr_ptr = sdmr | PSDMR_OP_NORM | PSDMR_RFEN;
- *base = c;
-
- size = get_ram_size((long *)base, maxsize);
-
- *orx_ptr = orx | ~(size - 1);
-
- return (size);
-}
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8260_t *memctl = &immap->im_memctl;
-
-#ifndef CONFIG_SYS_RAMBOOT
- ulong size8, size9;
-#endif
- long psize;
-
- psize = 32 * 1024 * 1024;
-
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
- memctl->memc_psrt = CONFIG_SYS_PSRT;
-
-#ifndef CONFIG_SYS_RAMBOOT
- /* 60x SDRAM setup:
- */
- size8 = try_init (memctl, CONFIG_SYS_PSDMR_8COL, CONFIG_SYS_OR2_8COL,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
- size9 = try_init (memctl, CONFIG_SYS_PSDMR_9COL, CONFIG_SYS_OR2_9COL,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
-
- if (size8 < size9) {
- psize = size9;
- printf ("(60x:9COL) ");
- } else {
- psize = try_init (memctl, CONFIG_SYS_PSDMR_8COL, CONFIG_SYS_OR2_8COL,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
- printf ("(60x:8COL) ");
- }
-
-#endif /* CONFIG_SYS_RAMBOOT */
-
- icache_enable ();
-
- return (psize);
-}
-
-#if defined(CONFIG_CMD_DOC)
-void doc_init (void)
-{
- doc_probe (CONFIG_SYS_DOC_BASE);
-}
-#endif
+++ /dev/null
-#ifndef __BOARD_CPU86__
-#define __BOARD_CPU86__
-
-#include <config.h>
-
-#define REG8(x) (*(volatile unsigned char *)(x))
-
-/* CPU86 register definitions */
-#define CPU86_VME_EAC REG8(CONFIG_SYS_BCRS_BASE + 0x00)
-#define CPU86_VME_SAC REG8(CONFIG_SYS_BCRS_BASE + 0x01)
-#define CPU86_VME_MAC REG8(CONFIG_SYS_BCRS_BASE + 0x02)
-#define CPU86_BCR REG8(CONFIG_SYS_BCRS_BASE + 0x03)
-#define CPU86_BSR REG8(CONFIG_SYS_BCRS_BASE + 0x04)
-#define CPU86_WDOG_RPORT REG8(CONFIG_SYS_BCRS_BASE + 0x05)
-#define CPU86_MBOX_IRQ REG8(CONFIG_SYS_BCRS_BASE + 0x04)
-#define CPU86_REV REG8(CONFIG_SYS_BCRS_BASE + 0x07)
-#define CPU86_VME_IRQMASK REG8(CONFIG_SYS_BCRS_BASE + 0x80)
-#define CPU86_VME_IRQSTATUS REG8(CONFIG_SYS_BCRS_BASE + 0x81)
-#define CPU86_LOCAL_IRQMASK REG8(CONFIG_SYS_BCRS_BASE + 0x82)
-#define CPU86_LOCAL_IRQSTATUS REG8(CONFIG_SYS_BCRS_BASE + 0x83)
-#define CPU86_PMCL_IRQSTATUS REG8(CONFIG_SYS_BCRS_BASE + 0x84)
-
-/* Board Control Register bits */
-#define CPU86_BCR_FWPT 0x01
-#define CPU86_BCR_FWRE 0x02
-
-#endif /* __BOARD_CPU86__ */
+++ /dev/null
-/*
- * (C) Copyright 2001, 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * Flash Routines for Intel devices
- *
- *--------------------------------------------------------------------
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-#include "cpu86.h"
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-/*-----------------------------------------------------------------------
- */
-ulong flash_int_get_size (volatile unsigned long *baseaddr,
- flash_info_t * info)
-{
- short i;
- unsigned long flashtest_h, flashtest_l;
-
- info->sector_count = info->size = 0;
- info->flash_id = FLASH_UNKNOWN;
-
- /* Write identify command sequence and test FLASH answer
- */
- baseaddr[0] = 0x00900090;
- baseaddr[1] = 0x00900090;
-
- flashtest_h = baseaddr[0]; /* manufacturer ID */
- flashtest_l = baseaddr[1];
-
- if (flashtest_h != INTEL_MANUFACT || flashtest_l != INTEL_MANUFACT)
- return (0); /* no or unknown flash */
-
- flashtest_h = baseaddr[2]; /* device ID */
- flashtest_l = baseaddr[3];
-
- if (flashtest_h != flashtest_l)
- return (0);
-
- switch (flashtest_h) {
- case INTEL_ID_28F160C3B:
- info->flash_id = FLASH_28F160C3B;
- info->sector_count = 39;
- info->size = 0x00800000; /* 4 * 2 MB = 8 MB */
- break;
- case INTEL_ID_28F160F3B:
- info->flash_id = FLASH_28F160F3B;
- info->sector_count = 39;
- info->size = 0x00800000; /* 4 * 2 MB = 8 MB */
- break;
- default:
- return (0); /* no or unknown flash */
- }
-
- info->flash_id |= INTEL_MANUFACT << 16; /* set manufacturer offset */
-
- if (info->flash_id & FLASH_BTYPE) {
- volatile unsigned long *tmp = baseaddr;
-
- /* set up sector start adress table (bottom sector type)
- * AND unlock the sectors (if our chip is 160C3)
- */
- for (i = 0; i < info->sector_count; i++) {
- if ((info->flash_id & FLASH_TYPEMASK) == FLASH_28F160C3B) {
- tmp[0] = 0x00600060;
- tmp[1] = 0x00600060;
- tmp[0] = 0x00D000D0;
- tmp[1] = 0x00D000D0;
- }
- info->start[i] = (uint) tmp;
- tmp += i < 8 ? 0x2000 : 0x10000; /* pointer arith */
- }
- }
-
- memset (info->protect, 0, info->sector_count);
-
- baseaddr[0] = 0x00FF00FF;
- baseaddr[1] = 0x00FF00FF;
-
- return (info->size);
-}
-
-static ulong flash_amd_get_size (vu_char *addr, flash_info_t *info)
-{
- short i;
- uchar vendor, devid;
- ulong base = (ulong)addr;
-
- /* Write auto select command: read Manufacturer ID */
- addr[0x0555] = 0xAA;
- addr[0x02AA] = 0x55;
- addr[0x0555] = 0x90;
-
- udelay(1000);
-
- vendor = addr[0];
- devid = addr[1] & 0xff;
-
- /* only support AMD */
- if (vendor != 0x01) {
- return 0;
- }
-
- vendor &= 0xf;
- devid &= 0xff;
-
- if (devid == AMD_ID_F040B) {
- info->flash_id = vendor << 16 | devid;
- info->sector_count = 8;
- info->size = info->sector_count * 0x10000;
- }
- else if (devid == AMD_ID_F080B) {
- info->flash_id = vendor << 16 | devid;
- info->sector_count = 16;
- info->size = 4 * info->sector_count * 0x10000;
- }
- else if (devid == AMD_ID_F016D) {
- info->flash_id = vendor << 16 | devid;
- info->sector_count = 32;
- info->size = 4 * info->sector_count * 0x10000;
- }
- else {
- printf ("## Unknown Flash Type: %02x\n", devid);
- return 0;
- }
-
- /* check for protected sectors */
- for (i = 0; i < info->sector_count; i++) {
- /* sector base address */
- info->start[i] = base + i * (info->size / info->sector_count);
- /* read sector protection at sector address, (A7 .. A0) = 0x02 */
- /* D0 = 1 if protected */
- addr = (volatile unsigned char *)(info->start[i]);
- info->protect[i] = addr[2] & 1;
- }
-
- /*
- * Prevent writes to uninitialized FLASH.
- */
- if (info->flash_id != FLASH_UNKNOWN) {
- addr = (vu_char *)info->start[0];
- addr[0] = 0xF0; /* reset bank */
- }
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-unsigned long flash_init (void)
-{
- unsigned long size_b0 = 0;
- unsigned long size_b1 = 0;
- int i;
-
- /* Init: no FLASHes known
- */
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- }
-
- /* Disable flash protection */
- CPU86_BCR |= (CPU86_BCR_FWPT | CPU86_BCR_FWRE);
-
- /* Static FLASH Bank configuration here (only one bank) */
-
- size_b0 = flash_int_get_size ((ulong *) CONFIG_SYS_FLASH_BASE, &flash_info[0]);
- size_b1 = flash_amd_get_size ((uchar *) CONFIG_SYS_BOOTROM_BASE, &flash_info[1]);
-
- if (size_b0 > 0 || size_b1 > 0) {
-
- printf("(");
-
- if (size_b0 > 0) {
- puts ("Bank#1 - ");
- print_size (size_b0, (size_b1 > 0) ? ", " : ") ");
- }
-
- if (size_b1 > 0) {
- puts ("Bank#2 - ");
- print_size (size_b1, ") ");
- }
- }
- else {
- printf ("## No FLASH found.\n");
- return 0;
- }
- /* protect monitor and environment sectors
- */
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_BOOTROM_BASE
- if (size_b1) {
- /* If U-Boot is booted from ROM the CONFIG_SYS_MONITOR_BASE > CONFIG_SYS_FLASH_BASE
- * but we shouldn't protect it.
- */
-
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1, &flash_info[1]
- );
- }
-#else
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1, &flash_info[0]
- );
-#endif
-#endif
-
-#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR)
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# if CONFIG_ENV_ADDR >= CONFIG_SYS_BOOTROM_BASE
- if (size_b1) {
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[1]);
- }
-# else
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
-# endif
-#endif
-
- return (size_b0 + size_b1);
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch ((info->flash_id >> 16) & 0xff) {
- case 0x89:
- printf ("INTEL ");
- break;
- case 0x1:
- printf ("AMD ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F160C3B:
- printf ("28F160C3B (16 Mbit, bottom sector)\n");
- break;
- case FLASH_28F160F3B:
- printf ("28F160F3B (16 Mbit, bottom sector)\n");
- break;
- case AMD_ID_F040B:
- printf ("AM29F040B (4 Mbit)\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
- if (info->size < 0x100000)
- printf (" Size: %ld KB in %d Sectors\n",
- info->size >> 10, info->sector_count);
- else
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
- printf ("\n");
-}
-
-/*-----------------------------------------------------------------------
- */
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- vu_char *addr = (vu_char *)(info->start[0]);
- int flag, prot, sect, l_sect;
- ulong start, now, last;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect])
- prot++;
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- /* Check the type of erased flash
- */
- if (info->flash_id >> 16 == 0x1) {
- /* Erase AMD flash
- */
- l_sect = -1;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[0x0555] = 0xAA;
- addr[0x02AA] = 0x55;
- addr[0x0555] = 0x80;
- addr[0x0555] = 0xAA;
- addr[0x02AA] = 0x55;
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (vu_char *)(info->start[sect]);
- addr[0] = 0x30;
- l_sect = sect;
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto AMD_DONE;
-
- start = get_timer (0);
- last = start;
- addr = (vu_char *)(info->start[l_sect]);
- while ((addr[0] & 0x80) != 0x80) {
- if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- serial_putc ('.');
- last = now;
- }
- }
-
-AMD_DONE:
- /* reset to read mode */
- addr = (volatile unsigned char *)info->start[0];
- addr[0] = 0xF0; /* reset bank */
-
- } else {
- /* Erase Intel flash
- */
-
- /* Start erase on unprotected sectors
- */
- for (sect = s_first; sect <= s_last; sect++) {
- volatile ulong *addr =
- (volatile unsigned long *) info->start[sect];
-
- start = get_timer (0);
- last = start;
- if (info->protect[sect] == 0) {
- /* Disable interrupts which might cause a timeout here
- */
- flag = disable_interrupts ();
-
- /* Erase the block
- */
- addr[0] = 0x00200020;
- addr[1] = 0x00200020;
- addr[0] = 0x00D000D0;
- addr[1] = 0x00D000D0;
-
- /* re-enable interrupts if necessary
- */
- if (flag)
- enable_interrupts ();
-
- /* wait at least 80us - let's wait 1 ms
- */
- udelay (1000);
-
- last = start;
- while ((addr[0] & 0x00800080) != 0x00800080 ||
- (addr[1] & 0x00800080) != 0x00800080) {
- if ((now = get_timer (start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout (erase suspended!)\n");
- /* Suspend erase
- */
- addr[0] = 0x00B000B0;
- addr[1] = 0x00B000B0;
- goto DONE;
- }
- /* show that we're waiting
- */
- if ((now - last) > 1000) { /* every second */
- serial_putc ('.');
- last = now;
- }
- }
- if (addr[0] & 0x00220022 || addr[1] & 0x00220022) {
- printf ("*** ERROR: erase failed!\n");
- goto DONE;
- }
- }
- /* Clear status register and reset to read mode
- */
- addr[0] = 0x00500050;
- addr[1] = 0x00500050;
- addr[0] = 0x00FF00FF;
- addr[1] = 0x00FF00FF;
- }
- }
-
- printf (" done\n");
-
-DONE:
- return 0;
-}
-
-static int write_word (flash_info_t *, volatile unsigned long *, ulong);
-static int write_byte (flash_info_t *info, ulong dest, uchar data);
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong v;
- int i, l, rc, cc = cnt, res = 0;
-
- if (info->flash_id >> 16 == 0x1) {
-
- /* Write to AMD 8-bit flash
- */
- while (cnt > 0) {
- if ((rc = write_byte(info, addr, *src)) != 0) {
- return (rc);
- }
- addr++;
- src++;
- cnt--;
- }
-
- return (0);
- } else {
-
- /* Write to Intel 64-bit flash
- */
- for (v=0; cc > 0; addr += 4, cc -= 4 - l) {
- l = (addr & 3);
- addr &= ~3;
-
- for (i = 0; i < 4; i++) {
- v = (v << 8) + (i < l || i - l >= cc ?
- *((unsigned char *) addr + i) : *src++);
- }
-
- if ((res = write_word (info, (volatile unsigned long *) addr, v)) != 0)
- break;
- }
- }
-
- return (res);
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t * info, volatile unsigned long *addr,
- ulong data)
-{
- int flag, res = 0;
- ulong start;
-
- /* Check if Flash is (sufficiently) erased
- */
- if ((*addr & data) != data)
- return (2);
-
- /* Disable interrupts which might cause a timeout here
- */
- flag = disable_interrupts ();
-
- *addr = 0x00400040;
- *addr = data;
-
- /* re-enable interrupts if necessary
- */
- if (flag)
- enable_interrupts ();
-
- start = get_timer (0);
- while ((*addr & 0x00800080) != 0x00800080) {
- if (get_timer (start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- /* Suspend program
- */
- *addr = 0x00B000B0;
- res = 1;
- goto OUT;
- }
- }
-
- if (*addr & 0x00220022) {
- printf ("*** ERROR: program failed!\n");
- res = 1;
- }
-
-OUT:
- /* Clear status register and reset to read mode
- */
- *addr = 0x00500050;
- *addr = 0x00FF00FF;
-
- return (res);
-}
-
-/*-----------------------------------------------------------------------
- * Write a byte to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_byte (flash_info_t *info, ulong dest, uchar data)
-{
- vu_char *addr = (vu_char *)(info->start[0]);
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*((vu_char *)dest) & data) != data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[0x0555] = 0xAA;
- addr[0x02AA] = 0x55;
- addr[0x0555] = 0xA0;
-
- *((vu_char *)dest) = data;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer (0);
- while ((*((vu_char *)dest) & 0x80) != (data & 0x80)) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- return (1);
- }
- }
- return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
+++ /dev/null
-if TARGET_CPU87
-
-config SYS_BOARD
- default "cpu87"
-
-config SYS_CONFIG_NAME
- default "CPU87"
-
-endif
+++ /dev/null
-CPU87 BOARD
-#M: -
-S: Maintained
-F: board/cpu87/
-F: include/configs/CPU87.h
-F: configs/CPU87_defconfig
-F: configs/CPU87_ROMBOOT_defconfig
+++ /dev/null
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = cpu87.o flash.o
+++ /dev/null
-/*
- * (C) Copyright 2001-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ioports.h>
-#include <mpc8260.h>
-#include "cpu87.h"
-#include <pci.h>
-#include <netdev.h>
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-
-const iop_conf_t iop_conf_tab[4][32] = {
-
- /* Port A configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PA31 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII COL */
- /* PA30 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII CRS */
- /* PA29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 MII TX_ER */
- /* PA28 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 MII TX_EN */
- /* PA27 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII RX_DV */
- /* PA26 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII RX_ER */
- /* PA25 */ { 1, 0, 0, 1, 0, 0 }, /* FCC2 MII MDIO */
- /* PA24 */ { 1, 0, 0, 1, 0, 0 }, /* FCC2 MII MDC */
- /* PA23 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 MII MDIO */
- /* PA22 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 MII MDC */
- /* PA21 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[3] */
- /* PA20 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[2] */
- /* PA19 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[1] */
- /* PA18 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[0] */
- /* PA17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[0] */
- /* PA16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[1] */
- /* PA15 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[2] */
- /* PA14 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[3] */
- /* PA13 */ { 1, 0, 0, 1, 0, 0 }, /* FCC2 MII TXSL1 */
- /* PA12 */ { 1, 0, 0, 1, 0, 1 }, /* FCC2 MII TXSL0 */
- /* PA11 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 MII TXSL1 */
- /* PA10 */ { 1, 0, 0, 1, 0, 1 }, /* FCC1 MII TXSL0 */
- /* PA9 */ { 0, 1, 0, 1, 0, 0 }, /* SMC2 TXD */
- /* PA8 */ { 0, 1, 0, 0, 0, 0 }, /* SMC2 RXD */
- /* PA7 */ { 0, 0, 0, 0, 0, 0 }, /* PA7 */
- /* PA6 */ { 1, 0, 0, 1, 0, 1 }, /* FCC2 MII PAUSE */
- /* PA5 */ { 1, 0, 0, 1, 0, 1 }, /* FCC1 MII PAUSE */
- /* PA4 */ { 1, 0, 0, 1, 0, 0 }, /* FCC2 MII PWRDN */
- /* PA3 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 MII PWRDN */
- /* PA2 */ { 0, 0, 0, 0, 0, 0 }, /* PA2 */
- /* PA1 */ { 1, 0, 0, 0, 0, 0 }, /* FCC2 MII MDINT */
- /* PA0 */ { 1, 0, 0, 1, 0, 0 } /* FCC1 MII MDINT */
- },
-
- /* Port B configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
- /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
- /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
- /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
- /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
- /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
- /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
- /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
- /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
- /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
- /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
- /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
- /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
- /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
- /* PB17 */ { 0, 0, 0, 0, 0, 0 }, /* PB17 */
- /* PB16 */ { 0, 0, 0, 0, 0, 0 }, /* PB16 */
- /* PB15 */ { 0, 0, 0, 0, 0, 0 }, /* PB15 */
- /* PB14 */ { 0, 0, 0, 0, 0, 0 }, /* PB14 */
- /* PB13 */ { 0, 0, 0, 0, 0, 0 }, /* PB13 */
- /* PB12 */ { 0, 0, 0, 0, 0, 0 }, /* PB12 */
- /* PB11 */ { 0, 0, 0, 0, 0, 0 }, /* PB11 */
- /* PB10 */ { 0, 0, 0, 0, 0, 0 }, /* PB10 */
- /* PB9 */ { 0, 0, 0, 0, 0, 0 }, /* PB9 */
- /* PB8 */ { 0, 0, 0, 0, 0, 0 }, /* PB8 */
- /* PB7 */ { 0, 0, 0, 0, 0, 0 }, /* PB7 */
- /* PB6 */ { 0, 0, 0, 0, 0, 0 }, /* PB6 */
- /* PB5 */ { 0, 0, 0, 0, 0, 0 }, /* PB5 */
- /* PB4 */ { 0, 0, 0, 0, 0, 0 }, /* PB4 */
- /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* PB3 */
- /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* PB2 */
- /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* PB1 */
- /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* PB0 */
- },
-
- /* Port C */
- { /* conf ppar psor pdir podr pdat */
- /* PC31 */ { 0, 0, 0, 0, 0, 0 }, /* PC31 */
- /* PC30 */ { 0, 0, 0, 0, 0, 0 }, /* PC30 */
- /* PC29 */ { 1, 0, 0, 0, 0, 0 }, /* SCC1 CTS */
- /* PC28 */ { 1, 0, 0, 0, 0, 0 }, /* SCC2 CTS */
- /* PC27 */ { 0, 0, 0, 0, 0, 0 }, /* PC27 */
- /* PC26 */ { 0, 0, 0, 0, 0, 0 }, /* PC26 */
- /* PC25 */ { 0, 0, 0, 0, 0, 0 }, /* PC25 */
- /* PC24 */ { 0, 0, 0, 0, 0, 0 }, /* PC24 */
- /* PC23 */ { 0, 0, 0, 0, 0, 0 }, /* FDC37C78 DACFD */
- /* PC22 */ { 0, 0, 0, 0, 0, 0 }, /* FDC37C78 DNFD */
- /* PC21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RX_CLK */
- /* PC20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII TX_CLK */
- /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK */
- /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII TX_CLK */
- /* PC17 */ { 0, 0, 0, 0, 0, 0 }, /* PC17 */
- /* PC16 */ { 0, 0, 0, 0, 0, 0 }, /* PC16 */
- /* PC15 */ { 0, 0, 0, 0, 0, 0 }, /* PC15 */
- /* PC14 */ { 0, 0, 0, 0, 0, 0 }, /* PC14 */
- /* PC13 */ { 0, 0, 0, 0, 0, 0 }, /* PC13 */
- /* PC12 */ { 0, 0, 0, 0, 0, 0 }, /* PC12 */
- /* PC11 */ { 0, 0, 0, 0, 0, 0 }, /* PC11 */
- /* PC10 */ { 0, 0, 0, 0, 0, 0 }, /* PC10 */
- /* PC9 */ { 0, 0, 0, 0, 0, 0 }, /* FC9 */
- /* PC8 */ { 0, 0, 0, 0, 0, 0 }, /* PC8 */
- /* PC7 */ { 0, 0, 0, 0, 0, 0 }, /* PC7 */
- /* PC6 */ { 0, 0, 0, 0, 0, 0 }, /* PC6 */
- /* PC5 */ { 0, 0, 0, 0, 0, 0 }, /* PC5 */
- /* PC4 */ { 0, 0, 0, 0, 0, 0 }, /* PC4 */
- /* PC3 */ { 0, 0, 0, 0, 0, 0 }, /* PC3 */
- /* PC2 */ { 0, 0, 0, 0, 0, 0 }, /* PC2 */
- /* PC1 */ { 0, 0, 0, 0, 0, 0 }, /* PC1 */
- /* PC0 */ { 0, 0, 0, 0, 0, 0 }, /* FDC37C78 DRQFD */
- },
-
- /* Port D */
- { /* conf ppar psor pdir podr pdat */
- /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 RXD */
- /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 TXD */
- /* PD29 */ { 1, 0, 0, 1, 0, 0 }, /* SCC1 RTS */
- /* PD28 */ { 1, 1, 0, 0, 0, 0 }, /* SCC2 RXD */
- /* PD27 */ { 1, 1, 0, 1, 0, 0 }, /* SCC2 TXD */
- /* PD26 */ { 1, 0, 0, 1, 0, 0 }, /* SCC2 RTS */
- /* PD25 */ { 0, 0, 0, 0, 0, 0 }, /* PD25 */
- /* PD24 */ { 0, 0, 0, 0, 0, 0 }, /* PD24 */
- /* PD23 */ { 0, 0, 0, 0, 0, 0 }, /* PD23 */
- /* PD22 */ { 0, 0, 0, 0, 0, 0 }, /* PD22 */
- /* PD21 */ { 0, 0, 0, 0, 0, 0 }, /* PD21 */
- /* PD20 */ { 0, 0, 0, 0, 0, 0 }, /* PD20 */
- /* PD19 */ { 0, 0, 0, 0, 0, 0 }, /* PD19 */
- /* PD18 */ { 0, 0, 0, 0, 0, 0 }, /* PD18 */
- /* PD17 */ { 0, 0, 0, 0, 0, 0 }, /* PD17 */
- /* PD16 */ { 0, 0, 0, 0, 0, 0 }, /* PD16 */
-#if defined(CONFIG_SYS_I2C_SOFT)
- /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SDA */
- /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SCL */
-#else
-#if defined(CONFIG_HARD_I2C)
- /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */
- /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */
-#else /* normal I/O port pins */
- /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */
- /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */
-#endif
-#endif
- /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
- /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
- /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
- /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
- /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TXD */
- /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RXD */
- /* PD7 */ { 0, 0, 0, 0, 0, 0 }, /* PD7 */
- /* PD6 */ { 0, 0, 0, 0, 0, 0 }, /* PD6 */
- /* PD5 */ { 0, 0, 0, 0, 0, 0 }, /* PD5 */
- /* PD4 */ { 0, 0, 0, 0, 0, 0 }, /* PD4 */
- /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* PD3 */
- /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* PD2 */
- /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* PD1 */
- /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* PD0 */
- }
-};
-
-/* ------------------------------------------------------------------------- */
-
-/* Check Board Identity:
- */
-int checkboard (void)
-{
- printf ("Board: CPU87 (Rev %02x)\n", CPU86_REV & 0x7f);
- return 0;
-}
-
-/* ------------------------------------------------------------------------- */
-
-/* Try SDRAM initialization with P/LSDMR=sdmr and ORx=orx
- *
- * This routine performs standard 8260 initialization sequence
- * and calculates the available memory size. It may be called
- * several times to try different SDRAM configurations on both
- * 60x and local buses.
- */
-static long int try_init (volatile memctl8260_t * memctl, ulong sdmr,
- ulong orx, volatile uchar * base)
-{
- volatile uchar c = 0xff;
- volatile uint *sdmr_ptr;
- volatile uint *orx_ptr;
- ulong maxsize, size;
- int i;
-
- /* We must be able to test a location outsize the maximum legal size
- * to find out THAT we are outside; but this address still has to be
- * mapped by the controller. That means, that the initial mapping has
- * to be (at least) twice as large as the maximum expected size.
- */
- maxsize = (1 + (~orx | 0x7fff)) / 2;
-
- /* Since CONFIG_SYS_SDRAM_BASE is always 0 (??), we assume that
- * we are configuring CS1 if base != 0
- */
- sdmr_ptr = &memctl->memc_psdmr;
- orx_ptr = &memctl->memc_or2;
-
- *orx_ptr = orx;
-
- /*
- * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
- *
- * "At system reset, initialization software must set up the
- * programmable parameters in the memory controller banks registers
- * (ORx, BRx, P/LSDMR). After all memory parameters are configured,
- * system software should execute the following initialization sequence
- * for each SDRAM device.
- *
- * 1. Issue a PRECHARGE-ALL-BANKS command
- * 2. Issue eight CBR REFRESH commands
- * 3. Issue a MODE-SET command to initialize the mode register
- *
- * The initial commands are executed by setting P/LSDMR[OP] and
- * accessing the SDRAM with a single-byte transaction."
- *
- * The appropriate BRx/ORx registers have already been set when we
- * get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE.
- */
-
- *sdmr_ptr = sdmr | PSDMR_OP_PREA;
- *base = c;
-
- *sdmr_ptr = sdmr | PSDMR_OP_CBRR;
- for (i = 0; i < 8; i++)
- *base = c;
-
- *sdmr_ptr = sdmr | PSDMR_OP_MRW;
- *(base + CONFIG_SYS_MRS_OFFS) = c; /* setting MR on address lines */
-
- *sdmr_ptr = sdmr | PSDMR_OP_NORM | PSDMR_RFEN;
- *base = c;
-
- size = get_ram_size((long *)base, maxsize);
-
- *orx_ptr = orx | ~(size - 1);
-
- return (size);
-}
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8260_t *memctl = &immap->im_memctl;
-
-#ifndef CONFIG_SYS_RAMBOOT
- ulong size8, size9, size10;
-#endif
- long psize;
-
- psize = 32 * 1024 * 1024;
-
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
- memctl->memc_psrt = CONFIG_SYS_PSRT;
-
-#ifndef CONFIG_SYS_RAMBOOT
- /* 60x SDRAM setup:
- */
- size8 = try_init (memctl, CONFIG_SYS_PSDMR_8COL, CONFIG_SYS_OR2_8COL,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
-
- size9 = try_init (memctl, CONFIG_SYS_PSDMR_9COL, CONFIG_SYS_OR2_9COL,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
-
- size10 = try_init (memctl, CONFIG_SYS_PSDMR_10COL, CONFIG_SYS_OR2_10COL,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
-
- psize = max(size8,max(size9,size10));
-
- if (psize == size8) {
- psize = try_init (memctl, CONFIG_SYS_PSDMR_8COL, CONFIG_SYS_OR2_8COL,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
- printf ("(60x:8COL) ");
- } else if (psize == size9){
- psize = try_init (memctl, CONFIG_SYS_PSDMR_9COL, CONFIG_SYS_OR2_9COL,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
- printf ("(60x:9COL) ");
- } else
- printf ("(60x:10COL) ");
-
-#endif /* CONFIG_SYS_RAMBOOT */
-
- icache_enable ();
-
- return (psize);
-}
-
-#if defined(CONFIG_CMD_DOC)
-void doc_init (void)
-{
- doc_probe (CONFIG_SYS_DOC_BASE);
-}
-#endif
-
-#ifdef CONFIG_PCI
-struct pci_controller hose;
-
-extern void pci_mpc8250_init(struct pci_controller *);
-
-void pci_init_board(void)
-{
- pci_mpc8250_init(&hose);
-}
-#endif
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
+++ /dev/null
-#ifndef __BOARD_CPU87__
-#define __BOARD_CPU87__
-
-#include <config.h>
-
-#define REG8(x) (*(volatile unsigned char *)(x))
-
-/* CPU86 register definitions */
-#define CPU86_VME_EAC REG8(CONFIG_SYS_BCRS_BASE + 0x00)
-#define CPU86_VME_SAC REG8(CONFIG_SYS_BCRS_BASE + 0x01)
-#define CPU86_VME_MAC REG8(CONFIG_SYS_BCRS_BASE + 0x02)
-#define CPU86_BCR REG8(CONFIG_SYS_BCRS_BASE + 0x03)
-#define CPU86_BSR REG8(CONFIG_SYS_BCRS_BASE + 0x04)
-#define CPU86_WDOG_RPORT REG8(CONFIG_SYS_BCRS_BASE + 0x05)
-#define CPU86_MBOX_IRQ REG8(CONFIG_SYS_BCRS_BASE + 0x04)
-#define CPU86_REV REG8(CONFIG_SYS_BCRS_BASE + 0x07)
-#define CPU86_VME_IRQMASK REG8(CONFIG_SYS_BCRS_BASE + 0x80)
-#define CPU86_VME_IRQSTATUS REG8(CONFIG_SYS_BCRS_BASE + 0x81)
-#define CPU86_LOCAL_IRQMASK REG8(CONFIG_SYS_BCRS_BASE + 0x82)
-#define CPU86_LOCAL_IRQSTATUS REG8(CONFIG_SYS_BCRS_BASE + 0x83)
-#define CPU86_PMCL_IRQSTATUS REG8(CONFIG_SYS_BCRS_BASE + 0x84)
-
-/* Board Control Register bits */
-#define CPU86_BCR_FWPT 0x01
-#define CPU86_BCR_FWRE 0x02
-
-#endif /* __BOARD_CPU87__ */
+++ /dev/null
-/*
- * (C) Copyright 2001-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * Flash Routines for Intel devices
- *
- *--------------------------------------------------------------------
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-#include "cpu87.h"
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-/*-----------------------------------------------------------------------
- */
-ulong flash_int_get_size (volatile unsigned long *baseaddr,
- flash_info_t * info)
-{
- short i;
- unsigned long flashtest_h, flashtest_l;
-
- info->sector_count = info->size = 0;
- info->flash_id = FLASH_UNKNOWN;
-
- /* Write identify command sequence and test FLASH answer
- */
- baseaddr[0] = 0x00900090;
- baseaddr[1] = 0x00900090;
-
- flashtest_h = baseaddr[0]; /* manufacturer ID */
- flashtest_l = baseaddr[1];
-
- if (flashtest_h != INTEL_MANUFACT || flashtest_l != INTEL_MANUFACT)
- return (0); /* no or unknown flash */
-
- flashtest_h = baseaddr[2]; /* device ID */
- flashtest_l = baseaddr[3];
-
- if (flashtest_h != flashtest_l)
- return (0);
-
- switch (flashtest_h) {
- case INTEL_ID_28F160C3B:
- info->flash_id = FLASH_28F160C3B;
- info->sector_count = 39;
- info->size = 0x00800000; /* 4 * 2 MB = 8 MB */
- break;
- case INTEL_ID_28F160F3B:
- info->flash_id = FLASH_28F160F3B;
- info->sector_count = 39;
- info->size = 0x00800000; /* 4 * 2 MB = 8 MB */
- break;
- case INTEL_ID_28F640C3B:
- info->flash_id = FLASH_28F640C3B;
- info->sector_count = 135;
- info->size = 0x02000000; /* 16 * 2 MB = 32 MB */
- break;
- default:
- return (0); /* no or unknown flash */
- }
-
- info->flash_id |= INTEL_MANUFACT << 16; /* set manufacturer offset */
-
- if (info->flash_id & FLASH_BTYPE) {
- volatile unsigned long *tmp = baseaddr;
-
- /* set up sector start adress table (bottom sector type)
- * AND unlock the sectors (if our chip is 160C3)
- */
- for (i = 0; i < info->sector_count; i++) {
- if (((info->flash_id & FLASH_TYPEMASK) == FLASH_28F160C3B) ||
- ((info->flash_id & FLASH_TYPEMASK) == FLASH_28F640C3B)) {
- tmp[0] = 0x00600060;
- tmp[1] = 0x00600060;
- tmp[0] = 0x00D000D0;
- tmp[1] = 0x00D000D0;
- }
- info->start[i] = (uint) tmp;
- tmp += i < 8 ? 0x2000 : 0x10000; /* pointer arith */
- }
- }
-
- memset (info->protect, 0, info->sector_count);
-
- baseaddr[0] = 0x00FF00FF;
- baseaddr[1] = 0x00FF00FF;
-
- return (info->size);
-}
-
-static ulong flash_amd_get_size (vu_char *addr, flash_info_t *info)
-{
- short i;
- uchar vendor, devid;
- ulong base = (ulong)addr;
-
- /* Write auto select command: read Manufacturer ID */
- addr[0x0555] = 0xAA;
- addr[0x02AA] = 0x55;
- addr[0x0555] = 0x90;
-
- udelay(1000);
-
- vendor = addr[0];
- devid = addr[1] & 0xff;
-
- /* only support AMD */
- if (vendor != 0x01) {
- return 0;
- }
-
- vendor &= 0xf;
- devid &= 0xff;
-
- if (devid == AMD_ID_F040B) {
- info->flash_id = vendor << 16 | devid;
- info->sector_count = 8;
- info->size = info->sector_count * 0x10000;
- }
- else if (devid == AMD_ID_F080B) {
- info->flash_id = vendor << 16 | devid;
- info->sector_count = 16;
- info->size = 4 * info->sector_count * 0x10000;
- }
- else if (devid == AMD_ID_F016D) {
- info->flash_id = vendor << 16 | devid;
- info->sector_count = 32;
- info->size = 4 * info->sector_count * 0x10000;
- }
- else {
- printf ("## Unknown Flash Type: %02x\n", devid);
- return 0;
- }
-
- /* check for protected sectors */
- for (i = 0; i < info->sector_count; i++) {
- /* sector base address */
- info->start[i] = base + i * (info->size / info->sector_count);
- /* read sector protection at sector address, (A7 .. A0) = 0x02 */
- /* D0 = 1 if protected */
- addr = (volatile unsigned char *)(info->start[i]);
- info->protect[i] = addr[2] & 1;
- }
-
- /*
- * Prevent writes to uninitialized FLASH.
- */
- if (info->flash_id != FLASH_UNKNOWN) {
- addr = (vu_char *)info->start[0];
- addr[0] = 0xF0; /* reset bank */
- }
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-unsigned long flash_init (void)
-{
- unsigned long size_b0 = 0;
- unsigned long size_b1 = 0;
- int i;
-
- /* Init: no FLASHes known
- */
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- }
-
- /* Disable flash protection */
- CPU86_BCR |= (CPU86_BCR_FWPT | CPU86_BCR_FWRE);
-
- /* Static FLASH Bank configuration here (only one bank) */
-
- size_b0 = flash_int_get_size ((ulong *) CONFIG_SYS_FLASH_BASE, &flash_info[0]);
- size_b1 = flash_amd_get_size ((uchar *) CONFIG_SYS_BOOTROM_BASE, &flash_info[1]);
-
- if (size_b0 > 0 || size_b1 > 0) {
-
- printf("(");
-
- if (size_b0 > 0) {
- puts ("Bank#1 - ");
- print_size (size_b0, (size_b1 > 0) ? ", " : ") ");
- }
-
- if (size_b1 > 0) {
- puts ("Bank#2 - ");
- print_size (size_b1, ") ");
- }
- }
- else {
- printf ("## No FLASH found.\n");
- return 0;
- }
- /* protect monitor and environment sectors
- */
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_BOOTROM_BASE
- if (size_b1) {
- /* If U-Boot is booted from ROM the CONFIG_SYS_MONITOR_BASE > CONFIG_SYS_FLASH_BASE
- * but we shouldn't protect it.
- */
-
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1, &flash_info[1]
- );
- }
-#else
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1, &flash_info[0]
- );
-#endif
-#endif
-
-#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR)
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# if CONFIG_ENV_ADDR >= CONFIG_SYS_BOOTROM_BASE
- if (size_b1) {
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[1]);
- }
-# else
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
-# endif
-#endif
-
- return (size_b0 + size_b1);
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch ((info->flash_id >> 16) & 0xff) {
- case 0x89:
- printf ("INTEL ");
- break;
- case 0x1:
- printf ("AMD ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F160C3B:
- printf ("28F160C3B (16 Mbit, bottom sector)\n");
- break;
- case FLASH_28F160F3B:
- printf ("28F160F3B (16 Mbit, bottom sector)\n");
- break;
- case FLASH_28F640C3B:
- printf ("28F640C3B (64 M, bottom sector)\n");
- break;
- case AMD_ID_F040B:
- printf ("AM29F040B (4 Mbit)\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
- if (info->size < 0x100000)
- printf (" Size: %ld KB in %d Sectors\n",
- info->size >> 10, info->sector_count);
- else
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
- printf ("\n");
-}
-
-/*-----------------------------------------------------------------------
- */
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- vu_char *addr = (vu_char *)(info->start[0]);
- int flag, prot, sect, l_sect;
- ulong start, now, last;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect])
- prot++;
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- /* Check the type of erased flash
- */
- if (info->flash_id >> 16 == 0x1) {
- /* Erase AMD flash
- */
- l_sect = -1;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[0x0555] = 0xAA;
- addr[0x02AA] = 0x55;
- addr[0x0555] = 0x80;
- addr[0x0555] = 0xAA;
- addr[0x02AA] = 0x55;
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (vu_char *)(info->start[sect]);
- addr[0] = 0x30;
- l_sect = sect;
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto AMD_DONE;
-
- start = get_timer (0);
- last = start;
- addr = (vu_char *)(info->start[l_sect]);
- while ((addr[0] & 0x80) != 0x80) {
- if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- serial_putc ('.');
- last = now;
- }
- }
-
-AMD_DONE:
- /* reset to read mode */
- addr = (volatile unsigned char *)info->start[0];
- addr[0] = 0xF0; /* reset bank */
-
- } else {
- /* Erase Intel flash
- */
-
- /* Start erase on unprotected sectors
- */
- for (sect = s_first; sect <= s_last; sect++) {
- volatile ulong *addr =
- (volatile unsigned long *) info->start[sect];
-
- start = get_timer (0);
- last = start;
- if (info->protect[sect] == 0) {
- /* Disable interrupts which might cause a timeout here
- */
- flag = disable_interrupts ();
-
- /* Erase the block
- */
- addr[0] = 0x00200020;
- addr[1] = 0x00200020;
- addr[0] = 0x00D000D0;
- addr[1] = 0x00D000D0;
-
- /* re-enable interrupts if necessary
- */
- if (flag)
- enable_interrupts ();
-
- /* wait at least 80us - let's wait 1 ms
- */
- udelay (1000);
-
- last = start;
- while ((addr[0] & 0x00800080) != 0x00800080 ||
- (addr[1] & 0x00800080) != 0x00800080) {
- if ((now = get_timer (start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout (erase suspended!)\n");
- /* Suspend erase
- */
- addr[0] = 0x00B000B0;
- addr[1] = 0x00B000B0;
- goto DONE;
- }
- /* show that we're waiting
- */
- if ((now - last) > 1000) { /* every second */
- serial_putc ('.');
- last = now;
- }
- }
- if (addr[0] & 0x00220022 || addr[1] & 0x00220022) {
- printf ("*** ERROR: erase failed!\n");
- goto DONE;
- }
- }
- /* Clear status register and reset to read mode
- */
- addr[0] = 0x00500050;
- addr[1] = 0x00500050;
- addr[0] = 0x00FF00FF;
- addr[1] = 0x00FF00FF;
- }
- }
-
- printf (" done\n");
-
-DONE:
- return 0;
-}
-
-static int write_word (flash_info_t *, volatile unsigned long *, ulong);
-static int write_byte (flash_info_t *info, ulong dest, uchar data);
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong v;
- int i, l, rc, cc = cnt, res = 0;
-
- if (info->flash_id >> 16 == 0x1) {
-
- /* Write to AMD 8-bit flash
- */
- while (cnt > 0) {
- if ((rc = write_byte(info, addr, *src)) != 0) {
- return (rc);
- }
- addr++;
- src++;
- cnt--;
- }
-
- return (0);
- } else {
-
- /* Write to Intel 64-bit flash
- */
- for (v=0; cc > 0; addr += 4, cc -= 4 - l) {
- l = (addr & 3);
- addr &= ~3;
-
- for (i = 0; i < 4; i++) {
- v = (v << 8) + (i < l || i - l >= cc ?
- *((unsigned char *) addr + i) : *src++);
- }
-
- if ((res = write_word (info, (volatile unsigned long *) addr, v)) != 0)
- break;
- }
- }
-
- return (res);
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t * info, volatile unsigned long *addr,
- ulong data)
-{
- int flag, res = 0;
- ulong start;
-
- /* Check if Flash is (sufficiently) erased
- */
- if ((*addr & data) != data)
- return (2);
-
- /* Disable interrupts which might cause a timeout here
- */
- flag = disable_interrupts ();
-
- *addr = 0x00400040;
- *addr = data;
-
- /* re-enable interrupts if necessary
- */
- if (flag)
- enable_interrupts ();
-
- start = get_timer (0);
- while ((*addr & 0x00800080) != 0x00800080) {
- if (get_timer (start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- /* Suspend program
- */
- *addr = 0x00B000B0;
- res = 1;
- goto OUT;
- }
- }
-
- if (*addr & 0x00220022) {
- printf ("*** ERROR: program failed!\n");
- res = 1;
- }
-
-OUT:
- /* Clear status register and reset to read mode
- */
- *addr = 0x00500050;
- *addr = 0x00FF00FF;
-
- return (res);
-}
-
-/*-----------------------------------------------------------------------
- * Write a byte to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_byte (flash_info_t *info, ulong dest, uchar data)
-{
- vu_char *addr = (vu_char *)(info->start[0]);
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*((vu_char *)dest) & data) != data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[0x0555] = 0xAA;
- addr[0x02AA] = 0x55;
- addr[0x0555] = 0xA0;
-
- *((vu_char *)dest) = data;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer (0);
- while ((*((vu_char *)dest) & 0x80) != (data & 0x80)) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- return (1);
- }
- }
- return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="BOOT_ROM"
-CONFIG_PPC=y
-CONFIG_MPC8260=y
-CONFIG_TARGET_CPU86=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_MPC8260=y
-CONFIG_TARGET_CPU86=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="BOOT_ROM"
-CONFIG_PPC=y
-CONFIG_MPC8260=y
-CONFIG_TARGET_CPU87=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_MPC8260=y
-CONFIG_TARGET_CPU87=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+CPU86 powerpc mpc8260 - - Wolfgang Denk <wd@denx.de>
+CPU87 powerpc mpc8260 - -
ep82xxm powerpc mpc8260 - -
gw8260 powerpc mpc8260 - - Oliver Brown <obrown@adventnetworks.com>
IPHASE4539 powerpc mpc8260 - - Wolfgang Grandegger <wg@denx.de>
+++ /dev/null
-/*
- * (C) Copyright 2001-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_CPU86 1 /* ...on a CPU86 board */
-#define CONFIG_CPM2 1 /* Has a CPM2 */
-
-#ifdef CONFIG_BOOT_ROM
-#define CONFIG_SYS_TEXT_BASE 0xFF800000
-#else
-#define CONFIG_SYS_TEXT_BASE 0xFF000000
-#endif
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere (for example, on the cogent platform, there are serial
- * ports on the motherboard which are used for the serial console - see
- * cogent/cma101/serial.[ch]).
- */
-#undef CONFIG_CONS_ON_SMC /* define if console on SMC */
-#define CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else*/
-#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
-
-#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
-#define CONFIG_BAUDRATE 230400
-#else
-#define CONFIG_BAUDRATE 9600
-#endif
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
-#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
-#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */
-
-#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1)
-
-/*
- * - Rx-CLK is CLK11
- * - Tx-CLK is CLK12
- * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
- * - Enable Full Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
-# define CONFIG_SYS_CPMFCR_RAMTYPE 0
-# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
-
-#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
-
-/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
- * - Enable Full Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
-# define CONFIG_SYS_CPMFCR_RAMTYPE 0
-# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
-
-#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
-
-/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
-#define CONFIG_8260_CLKIN 64000000 /* in Hz */
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT \
- "echo; " \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS; " \
- "echo"
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "bootp; " \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
- "bootm"
-
-/*-----------------------------------------------------------------------
- * I2C/EEPROM/RTC configuration
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE (iop->pdir |= 0x00010000)
-#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
-#define I2C_READ ((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
- else iop->pdat &= ~0x00010000
-#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
- else iop->pdat &= ~0x00020000
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configuration options
- */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 /* "bad" address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * Flash configuration
- */
-
-#define CONFIG_SYS_BOOTROM_BASE 0xFF800000
-#define CONFIG_SYS_BOOTROM_SIZE 0x00080000
-#define CONFIG_SYS_FLASH_BASE 0xFF000000
-#define CONFIG_SYS_FLASH_SIZE 0x00800000
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
-
-/*-----------------------------------------------------------------------
- * Other areas to be mapped
- */
-
-/* CS3: Dual ported SRAM */
-#define CONFIG_SYS_DPSRAM_BASE 0x40000000
-#define CONFIG_SYS_DPSRAM_SIZE 0x00020000
-
-/* CS4: DiskOnChip */
-#define CONFIG_SYS_DOC_BASE 0xF4000000
-#define CONFIG_SYS_DOC_SIZE 0x00100000
-
-/* CS5: FDC37C78 controller */
-#define CONFIG_SYS_FDC37C78_BASE 0xF1000000
-#define CONFIG_SYS_FDC37C78_SIZE 0x00100000
-
-/* CS6: Board configuration registers */
-#define CONFIG_SYS_BCRS_BASE 0xF2000000
-#define CONFIG_SYS_BCRS_SIZE 0x00010000
-
-/* CS7: VME Extended Access Range */
-#define CONFIG_SYS_VMEEAR_BASE 0x80000000
-#define CONFIG_SYS_VMEEAR_SIZE 0x01000000
-
-/* CS8: VME Standard Access Range */
-#define CONFIG_SYS_VMESAR_BASE 0xFE000000
-#define CONFIG_SYS_VMESAR_SIZE 0x01000000
-
-/* CS9: VME Short I/O Access Range */
-#define CONFIG_SYS_VMESIOAR_BASE 0xFD000000
-#define CONFIG_SYS_VMESIOAR_SIZE 0x01000000
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- *
- * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
- * defines for the various registers affected by the HRCW e.g. changing
- * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
- */
-#if defined(CONFIG_BOOT_ROM)
-#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \
- HRCW_BPS01 | HRCW_CS10PC01)
-#else
-#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | HRCW_CS10PC01)
-#endif
-
-/* no slaves so just fill with zeros */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xF0000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- *
- * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE.
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT
-#endif
-
-#if 0
-/* environment is in Flash */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#ifdef CONFIG_BOOT_ROM
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+0x70000)
-# define CONFIG_ENV_SIZE 0x10000
-# define CONFIG_ENV_SECT_SIZE 0x10000
-#endif
-#else
-/* environment is in EEPROM */
-#define CONFIG_ENV_IS_IN_EEPROM 1
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 /* EEPROM X24C16 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-#define CONFIG_ENV_OFFSET 512
-#define CONFIG_ENV_SIZE (2048 - 512)
-#endif
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers 2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|\
- HID0_DCI|HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID2 0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register 5-5
- *-----------------------------------------------------------------------
- * turn on Checkstop Reset Enable
- */
-#define CONFIG_SYS_RMR RMR_CSRE
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration 4-25
- *-----------------------------------------------------------------------
- */
-#define BCR_APD01 0x10000000
-#define CONFIG_SYS_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 4-31
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SIUMCR (SIUMCR_BBD|SIUMCR_DPPC00|SIUMCR_APPC10|\
- SIUMCR_CS10PC01|SIUMCR_BCTLC10)
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 4-35
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
- SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
- SYPCR_SWRI|SYPCR_SWP)
-#endif /* CONFIG_WATCHDOG */
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control 4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control 9-8
- *-----------------------------------------------------------------------
- * Ensure DFBRG is Divide by 16
- */
-#define CONFIG_SYS_SCCR SCCR_DFBRG01
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration 13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR 0
-
-#define CONFIG_SYS_MIN_AM_MASK 0xC0000000
-/*-----------------------------------------------------------------------
- * MPTPR - Memory Refresh Timer Prescaler Register 10-18
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_MPTPR 0x1F00
-
-/*-----------------------------------------------------------------------
- * PSRT - Refresh Timer Register 10-16
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_PSRT 0x0f
-
-/*-----------------------------------------------------------------------
- * PSRT - SDRAM Mode Register 10-10
- *-----------------------------------------------------------------------
- */
-
- /* SDRAM initialization values for 8-column chips
- */
-#define CONFIG_SYS_OR2_8COL (CONFIG_SYS_MIN_AM_MASK |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI0_A9 |\
- ORxS_NUMR_12)
-
-#define CONFIG_SYS_PSDMR_8COL (PSDMR_SDAM_A13_IS_A5 |\
- PSDMR_BSMA_A14_A16 |\
- PSDMR_SDA10_PBI0_A10 |\
- PSDMR_RFRC_7_CLK |\
- PSDMR_PRETOACT_2W |\
- PSDMR_ACTTORW_1W |\
- PSDMR_LDOTOPRE_1C |\
- PSDMR_WRC_1C |\
- PSDMR_CL_2)
-
- /* SDRAM initialization values for 9-column chips
- */
-#define CONFIG_SYS_OR2_9COL (CONFIG_SYS_MIN_AM_MASK |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI0_A7 |\
- ORxS_NUMR_13)
-
-#define CONFIG_SYS_PSDMR_9COL (PSDMR_SDAM_A14_IS_A5 |\
- PSDMR_BSMA_A13_A15 |\
- PSDMR_SDA10_PBI0_A9 |\
- PSDMR_RFRC_7_CLK |\
- PSDMR_PRETOACT_2W |\
- PSDMR_ACTTORW_1W |\
- PSDMR_LDOTOPRE_1C |\
- PSDMR_WRC_1C |\
- PSDMR_CL_2)
-
-/*
- * Init Memory Controller:
- *
- * Bank Bus Machine PortSz Device
- * ---- --- ------- ------ ------
- * 0 60x GPCM 8 bit Boot ROM
- * 1 60x GPCM 64 bit FLASH
- * 2 60x SDRAM 64 bit SDRAM
- *
- */
-
-#define CONFIG_SYS_MRS_OFFS 0x00000000
-
-#ifdef CONFIG_BOOT_ROM
-/* Bank 0 - Boot ROM
- */
-#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_BOOTROM_BASE & BRx_BA_MSK)|\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_BOOTROM_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_3_CLK |\
- ORxU_EHTR_8IDLE)
-
-/* Bank 1 - FLASH
- */
-#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_3_CLK |\
- ORxU_EHTR_8IDLE)
-
-#else /* CONFIG_BOOT_ROM */
-/* Bank 0 - FLASH
- */
-#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_3_CLK |\
- ORxU_EHTR_8IDLE)
-
-/* Bank 1 - Boot ROM
- */
-#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_BOOTROM_BASE & BRx_BA_MSK)|\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_BOOTROM_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_3_CLK |\
- ORxU_EHTR_8IDLE)
-
-#endif /* CONFIG_BOOT_ROM */
-
-
-/* Bank 2 - 60x bus SDRAM
- */
-#ifndef CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2_9COL
-
-#define CONFIG_SYS_PSDMR CONFIG_SYS_PSDMR_9COL
-#endif /* CONFIG_SYS_RAMBOOT */
-
-/* Bank 3 - Dual Ported SRAM
- */
-#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_DPSRAM_BASE & BRx_BA_MSK) |\
- BRx_PS_16 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR3_PRELIM (P2SZ_TO_AM(CONFIG_SYS_DPSRAM_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxG_SETA)
-
-/* Bank 4 - DiskOnChip
- */
-#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_DOC_BASE & BRx_BA_MSK) |\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR4_PRELIM (P2SZ_TO_AM(CONFIG_SYS_DOC_SIZE) |\
- ORxG_ACS_DIV2 |\
- ORxG_SCY_5_CLK |\
- ORxU_EHTR_8IDLE)
-
-/* Bank 5 - FDC37C78 controller
- */
-#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_FDC37C78_BASE & BRx_BA_MSK) |\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR5_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FDC37C78_SIZE) |\
- ORxG_ACS_DIV2 |\
- ORxG_SCY_8_CLK |\
- ORxU_EHTR_8IDLE)
-
-/* Bank 6 - Board control registers
- */
-#define CONFIG_SYS_BR6_PRELIM ((CONFIG_SYS_BCRS_BASE & BRx_BA_MSK) |\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR6_PRELIM (P2SZ_TO_AM(CONFIG_SYS_BCRS_SIZE) |\
- ORxG_CSNT |\
- ORxG_SCY_5_CLK)
-
-/* Bank 7 - VME Extended Access Range
- */
-#define CONFIG_SYS_BR7_PRELIM ((CONFIG_SYS_VMEEAR_BASE & BRx_BA_MSK) |\
- BRx_PS_32 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR7_PRELIM (P2SZ_TO_AM(CONFIG_SYS_VMEEAR_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxG_SETA)
-
-/* Bank 8 - VME Standard Access Range
- */
-#define CONFIG_SYS_BR8_PRELIM ((CONFIG_SYS_VMESAR_BASE & BRx_BA_MSK) |\
- BRx_PS_16 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR8_PRELIM (P2SZ_TO_AM(CONFIG_SYS_VMESAR_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxG_SETA)
-
-/* Bank 9 - VME Short I/O Access Range
- */
-#define CONFIG_SYS_BR9_PRELIM ((CONFIG_SYS_VMESIOAR_BASE & BRx_BA_MSK) |\
- BRx_PS_16 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR9_PRELIM (P2SZ_TO_AM(CONFIG_SYS_VMESIOAR_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxG_SETA)
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * (C) Copyright 2001-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_CPU87 1 /* ...on a CPU87 board */
-#define CONFIG_PCI
-#define CONFIG_CPM2 1 /* Has a CPM2 */
-
-#ifdef CONFIG_BOOT_ROM
-#define CONFIG_SYS_TEXT_BASE 0xFF800000
-#else
-#define CONFIG_SYS_TEXT_BASE 0xFF000000
-#endif
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere (for example, on the cogent platform, there are serial
- * ports on the motherboard which are used for the serial console - see
- * cogent/cma101/serial.[ch]).
- */
-#undef CONFIG_CONS_ON_SMC /* define if console on SMC */
-#define CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else*/
-#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
-
-#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
-#define CONFIG_BAUDRATE 230400
-#else
-#define CONFIG_BAUDRATE 9600
-#endif
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
-#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
-#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */
-
-#define CONFIG_HAS_ETH1 1
-#define CONFIG_HAS_ETH2 1
-
-#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1)
-
-/*
- * - Rx-CLK is CLK11
- * - Tx-CLK is CLK12
- * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
- * - Enable Full Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
-# define CONFIG_SYS_CPMFCR_RAMTYPE 0
-# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
-
-#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
-
-/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
- * - Enable Full Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
-# define CONFIG_SYS_CPMFCR_RAMTYPE 0
-# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
-
-#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
-
-/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
-#define CONFIG_8260_CLKIN 100000000 /* in Hz */
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT \
- "echo; " \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS; " \
- "echo"
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "bootp; " \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
- "bootm"
-
-/*-----------------------------------------------------------------------
- * I2C/EEPROM/RTC configuration
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE (iop->pdir |= 0x00010000)
-#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
-#define I2C_READ ((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
- else iop->pdat &= ~0x00010000
-#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
- else iop->pdat &= ~0x00020000
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Disk-On-Chip configuration
- */
-
-#define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
-
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configuration options
- */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
- #define CONFIG_CMD_PCI
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 /* "bad" address */
-
-#define CONFIG_LOOPW
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * Flash configuration
- */
-
-#define CONFIG_SYS_BOOTROM_BASE 0xFF800000
-#define CONFIG_SYS_BOOTROM_SIZE 0x00080000
-#define CONFIG_SYS_FLASH_BASE 0xFF000000
-#define CONFIG_SYS_FLASH_SIZE 0x00800000
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 135 /* max num of sects on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
-
-/*-----------------------------------------------------------------------
- * Other areas to be mapped
- */
-
-/* CS3: Dual ported SRAM */
-#define CONFIG_SYS_DPSRAM_BASE 0x40000000
-#define CONFIG_SYS_DPSRAM_SIZE 0x00100000
-
-/* CS4: DiskOnChip */
-#define CONFIG_SYS_DOC_BASE 0xF4000000
-#define CONFIG_SYS_DOC_SIZE 0x00100000
-
-/* CS5: FDC37C78 controller */
-#define CONFIG_SYS_FDC37C78_BASE 0xF1000000
-#define CONFIG_SYS_FDC37C78_SIZE 0x00100000
-
-/* CS6: Board configuration registers */
-#define CONFIG_SYS_BCRS_BASE 0xF2000000
-#define CONFIG_SYS_BCRS_SIZE 0x00010000
-
-/* CS7: VME Extended Access Range */
-#define CONFIG_SYS_VMEEAR_BASE 0x60000000
-#define CONFIG_SYS_VMEEAR_SIZE 0x01000000
-
-/* CS8: VME Standard Access Range */
-#define CONFIG_SYS_VMESAR_BASE 0xFE000000
-#define CONFIG_SYS_VMESAR_SIZE 0x01000000
-
-/* CS9: VME Short I/O Access Range */
-#define CONFIG_SYS_VMESIOAR_BASE 0xFD000000
-#define CONFIG_SYS_VMESIOAR_SIZE 0x01000000
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- *
- * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
- * defines for the various registers affected by the HRCW e.g. changing
- * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
- */
-#if defined(CONFIG_BOOT_ROM)
-#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \
- HRCW_BPS01 | HRCW_CS10PC01)
-#else
-#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | HRCW_CS10PC01)
-#endif
-
-/* no slaves so just fill with zeros */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xF0000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- *
- * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE.
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT
-#endif
-
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_PNP
-#define CONFIG_EEPRO100
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-#endif
-
-#if 0
-/* environment is in Flash */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#ifdef CONFIG_BOOT_ROM
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+0x70000)
-# define CONFIG_ENV_SIZE 0x10000
-# define CONFIG_ENV_SECT_SIZE 0x10000
-#endif
-#else
-/* environment is in EEPROM */
-#define CONFIG_ENV_IS_IN_EEPROM 1
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 /* EEPROM X24C16 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-#define CONFIG_ENV_OFFSET 512
-#define CONFIG_ENV_SIZE (2048 - 512)
-#endif
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers 2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|\
- HID0_DCI|HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID2 0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register 5-5
- *-----------------------------------------------------------------------
- * turn on Checkstop Reset Enable
- */
-#define CONFIG_SYS_RMR RMR_CSRE
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration 4-25
- *-----------------------------------------------------------------------
- */
-#define BCR_APD01 0x10000000
-#define CONFIG_SYS_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 4-31
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SIUMCR (SIUMCR_BBD|SIUMCR_DPPC00|SIUMCR_APPC10|\
- SIUMCR_CS10PC01|SIUMCR_BCTLC10)
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 4-35
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
- SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
- SYPCR_SWRI|SYPCR_SWP)
-#endif /* CONFIG_WATCHDOG */
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control 4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control 9-8
- *-----------------------------------------------------------------------
- * Ensure DFBRG is Divide by 16
- */
-#define CONFIG_SYS_SCCR SCCR_DFBRG01
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration 13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR 0
-
-#define CONFIG_SYS_MIN_AM_MASK 0xC0000000
-
-/*
- * we use the same values for 32 MB, 128 MB and 256 MB SDRAM
- * refresh rate = 7.68 uS (100 MHz Bus Clock)
- */
-
-/*-----------------------------------------------------------------------
- * MPTPR - Memory Refresh Timer Prescaler Register 10-18
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_MPTPR 0x2000
-
-/*-----------------------------------------------------------------------
- * PSRT - Refresh Timer Register 10-16
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_PSRT 0x16
-
-/*-----------------------------------------------------------------------
- * PSRT - SDRAM Mode Register 10-10
- *-----------------------------------------------------------------------
- */
-
- /* SDRAM initialization values for 8-column chips
- */
-#define CONFIG_SYS_OR2_8COL (CONFIG_SYS_MIN_AM_MASK |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI0_A9 |\
- ORxS_NUMR_12)
-
-#define CONFIG_SYS_PSDMR_8COL (PSDMR_SDAM_A13_IS_A5 |\
- PSDMR_BSMA_A14_A16 |\
- PSDMR_SDA10_PBI0_A10 |\
- PSDMR_RFRC_7_CLK |\
- PSDMR_PRETOACT_2W |\
- PSDMR_ACTTORW_2W |\
- PSDMR_LDOTOPRE_1C |\
- PSDMR_WRC_1C |\
- PSDMR_CL_2)
-
- /* SDRAM initialization values for 9-column chips
- */
-#define CONFIG_SYS_OR2_9COL (CONFIG_SYS_MIN_AM_MASK |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI0_A7 |\
- ORxS_NUMR_13)
-
-#define CONFIG_SYS_PSDMR_9COL (PSDMR_SDAM_A14_IS_A5 |\
- PSDMR_BSMA_A13_A15 |\
- PSDMR_SDA10_PBI0_A9 |\
- PSDMR_RFRC_7_CLK |\
- PSDMR_PRETOACT_2W |\
- PSDMR_ACTTORW_2W |\
- PSDMR_LDOTOPRE_1C |\
- PSDMR_WRC_1C |\
- PSDMR_CL_2)
-
- /* SDRAM initialization values for 10-column chips
- */
-#define CONFIG_SYS_OR2_10COL (CONFIG_SYS_MIN_AM_MASK |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI1_A4 |\
- ORxS_NUMR_13)
-
-#define CONFIG_SYS_PSDMR_10COL (PSDMR_PBI |\
- PSDMR_SDAM_A17_IS_A5 |\
- PSDMR_BSMA_A13_A15 |\
- PSDMR_SDA10_PBI1_A6 |\
- PSDMR_RFRC_7_CLK |\
- PSDMR_PRETOACT_2W |\
- PSDMR_ACTTORW_2W |\
- PSDMR_LDOTOPRE_1C |\
- PSDMR_WRC_1C |\
- PSDMR_CL_2)
-
-/*
- * Init Memory Controller:
- *
- * Bank Bus Machine PortSz Device
- * ---- --- ------- ------ ------
- * 0 60x GPCM 8 bit Boot ROM
- * 1 60x GPCM 64 bit FLASH
- * 2 60x SDRAM 64 bit SDRAM
- *
- */
-
-#define CONFIG_SYS_MRS_OFFS 0x00000000
-
-#ifdef CONFIG_BOOT_ROM
-/* Bank 0 - Boot ROM
- */
-#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_BOOTROM_BASE & BRx_BA_MSK)|\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_BOOTROM_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxU_EHTR_8IDLE)
-
-/* Bank 1 - FLASH
- */
-#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxU_EHTR_8IDLE)
-
-#else /* CONFIG_BOOT_ROM */
-/* Bank 0 - FLASH
- */
-#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxU_EHTR_8IDLE)
-
-/* Bank 1 - Boot ROM
- */
-#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_BOOTROM_BASE & BRx_BA_MSK)|\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_BOOTROM_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxU_EHTR_8IDLE)
-
-#endif /* CONFIG_BOOT_ROM */
-
-
-/* Bank 2 - 60x bus SDRAM
- */
-#ifndef CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2_8COL
-
-#define CONFIG_SYS_PSDMR CONFIG_SYS_PSDMR_8COL
-#endif /* CONFIG_SYS_RAMBOOT */
-
-/* Bank 3 - Dual Ported SRAM
- */
-#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_DPSRAM_BASE & BRx_BA_MSK) |\
- BRx_PS_16 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR3_PRELIM (P2SZ_TO_AM(CONFIG_SYS_DPSRAM_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_7_CLK |\
- ORxG_SETA)
-
-/* Bank 4 - DiskOnChip
- */
-#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_DOC_BASE & BRx_BA_MSK) |\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR4_PRELIM (P2SZ_TO_AM(CONFIG_SYS_DOC_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV2 |\
- ORxG_SCY_9_CLK |\
- ORxU_EHTR_8IDLE)
-
-/* Bank 5 - FDC37C78 controller
- */
-#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_FDC37C78_BASE & BRx_BA_MSK) |\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR5_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FDC37C78_SIZE) |\
- ORxG_ACS_DIV2 |\
- ORxG_SCY_10_CLK |\
- ORxU_EHTR_8IDLE)
-
-/* Bank 6 - Board control registers
- */
-#define CONFIG_SYS_BR6_PRELIM ((CONFIG_SYS_BCRS_BASE & BRx_BA_MSK) |\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR6_PRELIM (P2SZ_TO_AM(CONFIG_SYS_BCRS_SIZE) |\
- ORxG_CSNT |\
- ORxG_SCY_7_CLK)
-
-/* Bank 7 - VME Extended Access Range
- */
-#define CONFIG_SYS_BR7_PRELIM ((CONFIG_SYS_VMEEAR_BASE & BRx_BA_MSK) |\
- BRx_PS_32 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR7_PRELIM (P2SZ_TO_AM(CONFIG_SYS_VMEEAR_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_7_CLK |\
- ORxG_SETA)
-
-/* Bank 8 - VME Standard Access Range
- */
-#define CONFIG_SYS_BR8_PRELIM ((CONFIG_SYS_VMESAR_BASE & BRx_BA_MSK) |\
- BRx_PS_16 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR8_PRELIM (P2SZ_TO_AM(CONFIG_SYS_VMESAR_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_7_CLK |\
- ORxG_SETA)
-
-/* Bank 9 - VME Short I/O Access Range
- */
-#define CONFIG_SYS_BR9_PRELIM ((CONFIG_SYS_VMESIOAR_BASE & BRx_BA_MSK) |\
- BRx_PS_16 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR9_PRELIM (P2SZ_TO_AM(CONFIG_SYS_VMESIOAR_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_7_CLK |\
- ORxG_SETA)
-
-#endif /* __CONFIG_H */
projects / oweals / u-boot.git / commitdiff