T1040RDB, T1042RDB header files are very similar so merged into new header file T104xRDB.
T104xRDB header file can support both T1040RDB and T1042RDB_PI header.
Patch makes following changes
-Update Boards.cfg file for T1040RDB and T1042RDB_PI
-Add new T104xRDB header file
-Delete T1040RDB, T1042RDB_PI header file
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Active powerpc mpc85xx - freescale t1040qds T1040QDS T1040QDS:PPC_T1040 Poonam Aggrwal <poonam.aggrwal@freescale.com>
Active powerpc mpc85xx - freescale t1040qds T1040QDS_D4 T1040QDS:PPC_T1040,SYS_FSL_DDR4 Poonam Aggrwal <poonam.aggrwal@freescale.com>
Active powerpc mpc85xx - freescale t1040qds T1040QDS_SECURE_BOOT T1040QDS:PPC_T1040,SECURE_BOOT Aneesh Bansal <aneesh.bansal@freescale.com>
-Active powerpc mpc85xx - freescale t104xrdb T1040RDB T1040RDB:PPC_T1040 Poonam Aggrwal <poonam.aggrwal@freescale.com>
-Active powerpc mpc85xx - freescale t104xrdb T1040RDB_SECURE_BOOT T104
0RDB:PPC_T1040,SECURE_BOOT Aneesh Bansal <aneesh.bansal@freescale.com>
-Active powerpc mpc85xx - freescale t104xrdb T1042RDB_PI T1042RDB_PI:PPC_T1042 Poonam Aggrwal <poonam.aggrwal@freescale.com>
+Active powerpc mpc85xx - freescale t104xrdb T1040RDB T104xRDB:PPC_T1040,T1040RDB Priyanka Jain <Priyanka.Jain@freescale.com>
+Active powerpc mpc85xx - freescale t104xrdb T1040RDB_SECURE_BOOT T104
xRDB:PPC_T1040,SECURE_BOOT,T1040RDB Aneesh Bansal <aneesh.bansal@freescale.com>
+Active powerpc mpc85xx - freescale t104xrdb T1042RDB_PI T104xRDB:PPC_T1042,T1042RDB_PI Priyanka Jain <Priyanka.Jain@freescale.com>
Active powerpc mpc85xx - freescale t208xqds T2080QDS T208xQDS:PPC_T2080 -
Active powerpc mpc85xx - freescale t208xqds T2080QDS_SECURE_BOOT T208xQDS:PPC_T2080,SECURE_BOOT Aneesh Bansal <aneesh.bansal@freescale.com>
Active powerpc mpc85xx - freescale t208xqds T2080QDS_NAND T208xQDS:PPC_T2080,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF40000 -
+++ /dev/null
-/*
- * Copyright 2013 Freescale Semiconductor, Inc.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * T1040 RDB board configuration file
- */
-#define CONFIG_T104xRDB
-#define CONFIG_T1040RDB
-#define CONFIG_PHYS_64BIT
-
-#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
-#endif
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE
-#define CONFIG_E500 /* BOOKE e500 family */
-#define CONFIG_E500MC /* BOOKE e500mc family */
-#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
-#define CONFIG_MP /* support multiple processors */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xeff40000
-#endif
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
-#endif
-
-#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
-#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
-#define CONFIG_FSL_IFC /* Enable IFC Support */
-#define CONFIG_PCI /* Enable PCI/PCIE */
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCIE1 /* PCIE controler 1 */
-#define CONFIG_PCIE2 /* PCIE controler 2 */
-#define CONFIG_PCIE3 /* PCIE controler 3 */
-#define CONFIG_PCIE4 /* PCIE controler 4 */
-
-#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
-#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
-
-#define CONFIG_FSL_LAW /* Use common FSL init code */
-
-#define CONFIG_ENV_OVERWRITE
-
-#ifdef CONFIG_SYS_NO_FLASH
-#define CONFIG_ENV_IS_NOWHERE
-#else
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#endif
-
-#ifndef CONFIG_SYS_NO_FLASH
-#if defined(CONFIG_SPIFLASH)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#elif defined(CONFIG_SDCARD)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_OFFSET (512 * 1658)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#else
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
-#endif
-#else /* CONFIG_SYS_NO_FLASH */
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
-#endif
-
-#define CONFIG_SYS_CLK_FREQ 100000000
-#define CONFIG_DDR_CLK_FREQ 66666666
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_SYS_CACHE_STASHING
-#define CONFIG_BACKSIDE_L2_CACHE
-#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_DDR_ECC
-#ifdef CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
-#endif
-
-#define CONFIG_ENABLE_36BIT_PHYS
-
-#define CONFIG_ADDR_MAP
-#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
-
-#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00400000
-#define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
-
-/*
- * Config the L3 Cache as L3 SRAM
- */
-#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
-
-#define CONFIG_SYS_DCSRBAR 0xf0000000
-#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
-
-/*
- * DDR Setup
- */
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-#define CONFIG_DDR_SPD
-#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_SYS_FSL_DDR3
-
-#define CONFIG_SYS_SPD_BUS_NUM 0
-#define SPD_EEPROM_ADDRESS 0x51
-
-#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
-
-/*
- * IFC Definitions
- */
-#define CONFIG_SYS_FLASH_BASE 0xe8000000
-#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
-
-#define CONFIG_SYS_NOR_CSPR_EXT (0xf)
-#define CONFIG_SYS_NOR_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE) | \
- CSPR_PORT_SIZE_16 | \
- CSPR_MSEL_NOR | \
- CSPR_V)
-#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
-/* NOR Flash Timing Params */
-#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
-#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
- FTIM0_NOR_TEADC(0x5) | \
- FTIM0_NOR_TEAHC(0x5))
-#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
- FTIM1_NOR_TRAD_NOR(0x1A) |\
- FTIM1_NOR_TSEQRAD_NOR(0x13))
-#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
- FTIM2_NOR_TCH(0x4) | \
- FTIM2_NOR_TWPH(0x0E) | \
- FTIM2_NOR_TWP(0x1c))
-#define CONFIG_SYS_NOR_FTIM3 0x0
-
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
-
-/* CPLD on IFC */
-#define CONFIG_SYS_CPLD_BASE 0xffdf0000
-#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
-#define CONFIG_SYS_CSPR2_EXT (0xf)
-#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
- | CSPR_PORT_SIZE_8 \
- | CSPR_MSEL_GPCM \
- | CSPR_V)
-#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024)
-#define CONFIG_SYS_CSOR2 0x0
-/* CPLD Timing parameters for IFC CS2 */
-#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
- FTIM0_GPCM_TEADC(0x0e) | \
- FTIM0_GPCM_TEAHC(0x0e))
-#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
- FTIM1_GPCM_TRAD(0x1f))
-#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
- FTIM2_GPCM_TCH(0x0) | \
- FTIM2_GPCM_TWP(0x1f))
-#define CONFIG_SYS_CS2_FTIM3 0x0
-
-/* NAND Flash on IFC */
-#define CONFIG_NAND_FSL_IFC
-#define CONFIG_SYS_NAND_BASE 0xff800000
-#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
-
-#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
-#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
- | CSPR_MSEL_NAND /* MSEL = NAND */ \
- | CSPR_V)
-#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
-
-#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
- | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
- | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
- | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
- | CSOR_NAND_PGS_4K /* Page Size = 4K */ \
- | CSOR_NAND_SPRZ_224/* Spare size = 224 */ \
- | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
- FTIM0_NAND_TWP(0x18) | \
- FTIM0_NAND_TWCHT(0x07) | \
- FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
- FTIM1_NAND_TWBE(0x39) | \
- FTIM1_NAND_TRR(0x0e) | \
- FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
- FTIM2_NAND_TREH(0x0a) | \
- FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3 0x0
-
-#define CONFIG_SYS_NAND_DDR_LAW 11
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND
-
-#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
-
-#if defined(CONFIG_NAND)
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
-#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR_CSPR_EXT
-#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR_CSPR
-#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
-#else
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
-#endif
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-#if defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_BOARD_EARLY_INIT_R
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_HWCONFIG
-
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000
-/* The assembler doesn't like typecast */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
- ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
- CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
-
-/* Serial Port - controlled on board with jumper J8
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
-#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
-#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
-#define CONFIG_SERIAL_MULTI /* Enable both serial ports */
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */
-#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000
-
-/* I2C bus multiplexer */
-#define I2C_MUX_PCA_ADDR 0x70
-#define I2C_MUX_CH_DEFAULT 0x8
-
-
-/*
- * eSPI - Enhanced SPI
- */
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_CMD_SF
-#define CONFIG_SF_DEFAULT_SPEED 10000000
-#define CONFIG_SF_DEFAULT_MODE 0
-#define CONFIG_ENV_SPI_BUS 0
-#define CONFIG_ENV_SPI_CS 0
-#define CONFIG_ENV_SPI_MAX_HZ 10000000
-#define CONFIG_ENV_SPI_MODE 0
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-#ifdef CONFIG_PCI
-/* controller 1, direct to uli, tgtid 3, Base address 20000 */
-#ifdef CONFIG_PCIE1
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-#endif
-
-/* controller 2, Slot 2, tgtid 2, Base address 201000 */
-#ifdef CONFIG_PCIE2
-#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
-#endif
-
-/* controller 3, Slot 1, tgtid 1, Base address 202000 */
-#ifdef CONFIG_PCIE3
-#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
-#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
-#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
-#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
-#endif
-
-/* controller 4, Base address 203000 */
-#ifdef CONFIG_PCIE4
-#define CONFIG_SYS_PCIE4_MEM_VIRT 0xb0000000
-#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc30000000ull
-#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE4_IO_VIRT 0xf8030000
-#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
-#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
-#endif
-
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_E1000
-
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
-#endif /* CONFIG_PCI */
-
-/* SATA */
-#define CONFIG_FSL_SATA_V2
-#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_LIBATA
-#define CONFIG_FSL_SATA
-
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
-#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
-
-#define CONFIG_LBA48
-#define CONFIG_CMD_SATA
-#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
-#endif
-
-/*
-* USB
-*/
-#define CONFIG_HAS_FSL_DR_USB
-
-#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_CMD_EXT2
-#endif
-#endif
-
-#define CONFIG_MMC
-
-#ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC
-#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_CMD_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
-/* Qman/Bman */
-#ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
-#define CONFIG_SYS_BMAN_NUM_PORTALS 25
-#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
-#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
-#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
-#define CONFIG_SYS_QMAN_NUM_PORTALS 25
-#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
-#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
-#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
-
-#define CONFIG_SYS_DPAA_FMAN
-#define CONFIG_SYS_DPAA_PME
-
-#define CONFIG_QE
-#define CONFIG_U_QE
-
-/* Default address of microcode for the Linux Fman driver */
-#if defined(CONFIG_SPIFLASH)
-/*
- * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
- * env, so we got 0x110000.
- */
-#define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
-#elif defined(CONFIG_SDCARD)
-/*
- * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 825KB (1650 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
- */
-#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_FMAN_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#else
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
-#define CONFIG_SYS_QE_FW_ADDR 0xEFF10000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
-#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-#endif /* CONFIG_NOBQFMAN */
-
-#ifdef CONFIG_SYS_DPAA_FMAN
-#define CONFIG_FMAN_ENET
-#define CONFIG_PHY_VITESSE
-#define CONFIG_PHY_REALTEK
-#endif
-
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_SYS_SGMII1_PHY_ADDR 0x03
-#define CONFIG_SYS_RGMII1_PHY_ADDR 0x01
-#define CONFIG_SYS_RGMII2_PHY_ADDR 0x02
-
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_ETHPRIME "FM1@DTSEC4"
-#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
-#endif
-
-/*
- * Environment
- */
-#define CONFIG_LOADS_ECHO /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_GREPENV
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SETEXPR
-
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 1000000
-
-#define CONFIG_BOOTDELAY 10 /*-1 disables auto-boot*/
-
-#define CONFIG_BAUDRATE 115200
-
-#define __USB_PHY_TYPE utmi
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "hwconfig=fsl_ddr:bank_intlv=cs0_cs1;" \
- "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
- "usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
- "netdev=eth0\0" \
- "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
- "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
- "tftpflash=tftpboot $loadaddr $uboot && " \
- "protect off $ubootaddr +$filesize && " \
- "erase $ubootaddr +$filesize && " \
- "cp.b $loadaddr $ubootaddr $filesize && " \
- "protect on $ubootaddr +$filesize && " \
- "cmp.b $loadaddr $ubootaddr $filesize\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "ramdiskfile=t1040rdb/ramdisk.uboot\0" \
- "fdtaddr=c00000\0" \
- "fdtfile=t1040rdb/t1040rdb.dtb\0" \
- "bdev=sda3\0" \
- "c=ffe\0"
-
-#define CONFIG_LINUX \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "setenv ramdiskaddr 0x02000000;" \
- "setenv fdtaddr 0x00c00000;" \
- "setenv loadaddr 0x1000000;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_HDBOOT \
- "setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_LINUX
-
-#ifdef CONFIG_SECURE_BOOT
-#include <asm/fsl_secure_boot.h>
-#endif
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * Copyright 2013 Freescale Semiconductor, Inc.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * T1042RDB_PI board configuration file
- */
-#define CONFIG_T104xRDB
-#define CONFIG_T1042RDB_PI
-#define CONFIG_PHYS_64BIT
-
-#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
-#endif
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE
-#define CONFIG_E500 /* BOOKE e500 family */
-#define CONFIG_E500MC /* BOOKE e500mc family */
-#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
-#define CONFIG_MP /* support multiple processors */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xeff40000
-#endif
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
-#endif
-
-#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
-#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
-#define CONFIG_FSL_IFC /* Enable IFC Support */
-#define CONFIG_PCI /* Enable PCI/PCIE */
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCIE1 /* PCIE controler 1 */
-#define CONFIG_PCIE2 /* PCIE controler 2 */
-#define CONFIG_PCIE3 /* PCIE controler 3 */
-#define CONFIG_PCIE4 /* PCIE controler 4 */
-
-#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
-#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
-
-#define CONFIG_FSL_LAW /* Use common FSL init code */
-
-#define CONFIG_ENV_OVERWRITE
-
-#ifdef CONFIG_SYS_NO_FLASH
-#define CONFIG_ENV_IS_NOWHERE
-#else
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#endif
-
-#ifndef CONFIG_SYS_NO_FLASH
-#if defined(CONFIG_SPIFLASH)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#elif defined(CONFIG_SDCARD)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_OFFSET (512 * 1658)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#else
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
-#endif
-#else /* CONFIG_SYS_NO_FLASH */
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
-#endif
-
-#define CONFIG_SYS_CLK_FREQ 100000000
-#define CONFIG_DDR_CLK_FREQ 66666666
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_SYS_CACHE_STASHING
-#define CONFIG_BACKSIDE_L2_CACHE
-#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_DDR_ECC
-#ifdef CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
-#endif
-
-#define CONFIG_ENABLE_36BIT_PHYS
-
-#define CONFIG_ADDR_MAP
-#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
-
-#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00400000
-#define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
-
-/*
- * Config the L3 Cache as L3 SRAM
- */
-#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
-
-#define CONFIG_SYS_DCSRBAR 0xf0000000
-#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
-
-/*
- * DDR Setup
- */
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-#define CONFIG_DDR_SPD
-#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_SYS_FSL_DDR3
-
-#define CONFIG_SYS_SPD_BUS_NUM 0
-#define SPD_EEPROM_ADDRESS 0x51
-
-#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
-
-/*
- * IFC Definitions
- */
-#define CONFIG_SYS_FLASH_BASE 0xe8000000
-#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
-
-#define CONFIG_SYS_NOR_CSPR_EXT (0xf)
-#define CONFIG_SYS_NOR_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE) | \
- CSPR_PORT_SIZE_16 | \
- CSPR_MSEL_NOR | \
- CSPR_V)
-#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
-/* NOR Flash Timing Params */
-#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
-#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
- FTIM0_NOR_TEADC(0x5) | \
- FTIM0_NOR_TEAHC(0x5))
-#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
- FTIM1_NOR_TRAD_NOR(0x1A) |\
- FTIM1_NOR_TSEQRAD_NOR(0x13))
-#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
- FTIM2_NOR_TCH(0x4) | \
- FTIM2_NOR_TWPH(0x0E) | \
- FTIM2_NOR_TWP(0x1c))
-#define CONFIG_SYS_NOR_FTIM3 0x0
-
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
-
-/* CPLD on IFC */
-#define CONFIG_SYS_CPLD_BASE 0xffdf0000
-#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
-#define CONFIG_SYS_CSPR2_EXT (0xf)
-#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
- | CSPR_PORT_SIZE_8 \
- | CSPR_MSEL_GPCM \
- | CSPR_V)
-#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024)
-#define CONFIG_SYS_CSOR2 0x0
-/* CPLD Timing parameters for IFC CS2 */
-#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
- FTIM0_GPCM_TEADC(0x0e) | \
- FTIM0_GPCM_TEAHC(0x0e))
-#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
- FTIM1_GPCM_TRAD(0x1f))
-#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
- FTIM2_GPCM_TCH(0x0) | \
- FTIM2_GPCM_TWP(0x1f))
-#define CONFIG_SYS_CS2_FTIM3 0x0
-
-/* NAND Flash on IFC */
-#define CONFIG_NAND_FSL_IFC
-#define CONFIG_SYS_NAND_BASE 0xff800000
-#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
-
-#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
-#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
- | CSPR_MSEL_NAND /* MSEL = NAND */ \
- | CSPR_V)
-#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
-
-#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
- | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
- | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
- | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
- | CSOR_NAND_PGS_4K /* Page Size = 4K */ \
- | CSOR_NAND_SPRZ_224/* Spare size = 224 */ \
- | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
- FTIM0_NAND_TWP(0x18) | \
- FTIM0_NAND_TWCHT(0x07) | \
- FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
- FTIM1_NAND_TWBE(0x39) | \
- FTIM1_NAND_TRR(0x0e) | \
- FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
- FTIM2_NAND_TREH(0x0a) | \
- FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3 0x0
-
-#define CONFIG_SYS_NAND_DDR_LAW 11
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND
-
-#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
-
-#if defined(CONFIG_NAND)
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
-#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR_CSPR_EXT
-#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR_CSPR
-#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
-#else
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
-#endif
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-#if defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_BOARD_EARLY_INIT_R
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_HWCONFIG
-
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000
-/* The assembler doesn't like typecast */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
- ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
- CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
-
-/* Serial Port - controlled on board with jumper J8
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
-#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
-#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
-#define CONFIG_SERIAL_MULTI /* Enable both serial ports */
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */
-#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000
-
-/* I2C bus multiplexer */
-#define I2C_MUX_PCA_ADDR 0x70
-
-/*
- * RTC configuration
- */
-#define RTC
-#define CONFIG_RTC_DS1337 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/*DVI encoder*/
-#define CONFIG_HDMI_ENCODER_I2C_ADDR 0x75
-
-/*
- * eSPI - Enhanced SPI
- */
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_CMD_SF
-#define CONFIG_SF_DEFAULT_SPEED 10000000
-#define CONFIG_SF_DEFAULT_MODE 0
-#define CONFIG_ENV_SPI_BUS 0
-#define CONFIG_ENV_SPI_CS 0
-#define CONFIG_ENV_SPI_MAX_HZ 10000000
-#define CONFIG_ENV_SPI_MODE 0
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-#ifdef CONFIG_PCI
-/* controller 1, direct to uli, tgtid 3, Base address 20000 */
-#ifdef CONFIG_PCIE1
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-#endif
-
-/* controller 2, Slot 2, tgtid 2, Base address 201000 */
-#ifdef CONFIG_PCIE2
-#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
-#endif
-
-/* controller 3, Slot 1, tgtid 1, Base address 202000 */
-#ifdef CONFIG_PCIE3
-#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
-#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
-#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
-#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
-#endif
-
-/* controller 4, Base address 203000 */
-#ifdef CONFIG_PCIE4
-#define CONFIG_SYS_PCIE4_MEM_VIRT 0xb0000000
-#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc30000000ull
-#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE4_IO_VIRT 0xf8030000
-#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
-#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
-#endif
-
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_E1000
-
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
-#endif /* CONFIG_PCI */
-
-/* SATA */
-#define CONFIG_FSL_SATA_V2
-#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_LIBATA
-#define CONFIG_FSL_SATA
-
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
-#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
-
-#define CONFIG_LBA48
-#define CONFIG_CMD_SATA
-#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
-#endif
-
-/*
-* USB
-*/
-#define CONFIG_HAS_FSL_DR_USB
-
-#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_CMD_EXT2
-#endif
-#endif
-
-#define CONFIG_MMC
-
-#ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC
-#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_CMD_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
-/* Qman/Bman */
-#ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
-#define CONFIG_SYS_BMAN_NUM_PORTALS 25
-#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
-#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
-#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
-#define CONFIG_SYS_QMAN_NUM_PORTALS 25
-#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
-#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
-#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
-
-#define CONFIG_SYS_DPAA_FMAN
-#define CONFIG_SYS_DPAA_PME
-
-/* Default address of microcode for the Linux Fman driver */
-#if defined(CONFIG_SPIFLASH)
-/*
- * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
- * env, so we got 0x110000.
- */
-#define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
-#elif defined(CONFIG_SDCARD)
-/*
- * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 825KB (1650 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
- */
-#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_FMAN_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#else
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
-#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-#endif /* CONFIG_NOBQFMAN */
-
-#ifdef CONFIG_SYS_DPAA_FMAN
-#define CONFIG_FMAN_ENET
-#define CONFIG_PHY_VITESSE
-#define CONFIG_PHY_REALTEK
-#endif
-
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_SYS_RGMII1_PHY_ADDR 0x01
-#define CONFIG_SYS_RGMII2_PHY_ADDR 0x02
-
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_ETHPRIME "FM1@DTSEC4"
-#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
-#endif
-
-/*
- * Environment
- */
-#define CONFIG_LOADS_ECHO /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_GREPENV
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SETEXPR
-
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 1000000
-
-#define CONFIG_BOOTDELAY 10 /*-1 disables auto-boot*/
-
-#define CONFIG_BAUDRATE 115200
-
-#define __USB_PHY_TYPE utmi
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "hwconfig=fsl_ddr:bank_intlv=cs0_cs1;" \
- "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
- "usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
- "netdev=eth0\0" \
- "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
- "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
- "tftpflash=tftpboot $loadaddr $uboot && " \
- "protect off $ubootaddr +$filesize && " \
- "erase $ubootaddr +$filesize && " \
- "cp.b $loadaddr $ubootaddr $filesize && " \
- "protect on $ubootaddr +$filesize && " \
- "cmp.b $loadaddr $ubootaddr $filesize\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "ramdiskfile=t1040rdb_pi/ramdisk.uboot\0" \
- "fdtaddr=c00000\0" \
- "fdtfile=t1040rdb_pi/t1040rdb_pi.dtb\0" \
- "bdev=sda3\0" \
- "c=ffe\0"
-
-#define CONFIG_LINUX \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "setenv ramdiskaddr 0x02000000;" \
- "setenv fdtaddr 0x00c00000;" \
- "setenv loadaddr 0x1000000;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_HDBOOT \
- "setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_LINUX
-
-#ifdef CONFIG_SECURE_BOOT
-#include <asm/fsl_secure_boot.h>
-#endif
-
-#endif /* __CONFIG_H */
--- /dev/null
+/*
++ * Copyright 2014 Freescale Semiconductor, Inc.
++ *
++ * SPDX-License-Identifier: GPL-2.0+
++ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * T104x RDB board configuration file
+ */
+#define CONFIG_T104xRDB
+#define CONFIG_PHYS_64BIT
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_E500MC /* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
+#define CONFIG_MP /* support multiple processors */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff40000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
+#endif
+
+#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_IFC /* Enable IFC Support */
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_PCIE1 /* PCIE controler 1 */
+#define CONFIG_PCIE2 /* PCIE controler 2 */
+#define CONFIG_PCIE3 /* PCIE controler 3 */
+#define CONFIG_PCIE4 /* PCIE controler 4 */
+
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_IS_NOWHERE
+#else
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+#ifndef CONFIG_SYS_NO_FLASH
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET (512 * 1658)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#endif
+#else /* CONFIG_SYS_NO_FLASH */
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#endif
+
+#define CONFIG_SYS_CLK_FREQ 100000000
+#define CONFIG_DDR_CLK_FREQ 66666666
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BACKSIDE_L2_CACHE
+#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#endif
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#define CONFIG_ADDR_MAP
+#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+
+/*
+ * Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
+
+#define CONFIG_SYS_DCSRBAR 0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_DDR_RAW_TIMING
+#define CONFIG_SYS_FSL_DDR3
+
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS 0x51
+
+#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE 0xe8000000
+#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+
+#define CONFIG_SYS_NOR_CSPR_EXT (0xf)
+#define CONFIG_SYS_NOR_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
+ FTIM0_NOR_TEADC(0x5) | \
+ FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
+ FTIM1_NOR_TRAD_NOR(0x1A) |\
+ FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWPH(0x0E) | \
+ FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3 0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
+
+/* CPLD on IFC */
+#define CONFIG_SYS_CPLD_BASE 0xffdf0000
+#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
+#define CONFIG_SYS_CSPR2_EXT (0xf)
+#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024)
+#define CONFIG_SYS_CSOR2 0x0
+/* CPLD Timing parameters for IFC CS2 */
+#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
+ FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
+ FTIM2_GPCM_TCH(0x0) | \
+ FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS2_FTIM3 0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE 0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+ | CSPR_MSEL_NAND /* MSEL = NAND */ \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
+ | CSOR_NAND_PGS_4K /* Page Size = 4K */ \
+ | CSOR_NAND_SPRZ_224/* Spare size = 224 */ \
+ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x07) | \
+ FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0x0e) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW 11
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
+#define CONFIG_SERIAL_MULTI /* Enable both serial ports */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */
+#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000
+
+/* I2C bus multiplexer */
+#define I2C_MUX_PCA_ADDR 0x70
+#ifdef CONFIG_T1040RDB
+#define I2C_MUX_CH_DEFAULT 0x8
+#endif
+
+#ifdef CONFIG_T1042RDB_PI
+/*
+ * RTC configuration
+ */
+#define RTC
+#define CONFIG_RTC_DS1337 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+
+/*DVI encoder*/
+#define CONFIG_HDMI_ENCODER_I2C_ADDR 0x75
+#endif
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE 0
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+#ifdef CONFIG_PCI
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#ifdef CONFIG_PCIE1
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+#endif
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#ifdef CONFIG_PCIE2
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+#endif
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#ifdef CONFIG_PCIE3
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+#endif
+
+/* controller 4, Base address 203000 */
+#ifdef CONFIG_PCIE4
+#define CONFIG_SYS_PCIE4_MEM_VIRT 0xb0000000
+#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc30000000ull
+#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE4_IO_VIRT 0xf8030000
+#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
+#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
+#endif
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_E1000
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif /* CONFIG_PCI */
+
+/* SATA */
+#define CONFIG_FSL_SATA_V2
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+
+#define CONFIG_SYS_SATA_MAX_DEVICE 1
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
+
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+/*
+* USB
+*/
+#define CONFIG_HAS_FSL_DR_USB
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#endif
+#endif
+
+#define CONFIG_MMC
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS 25
+#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS 25
+#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
+#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+
+#define CONFIG_QE
+#define CONFIG_U_QE
+
+/* Default address of microcode for the Linux Fman driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 825KB (1650 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_FMAN_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
+#define CONFIG_SYS_QE_FW_ADDR 0xEFF10000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
+#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#ifdef CONFIG_T1040RDB
+#define CONFIG_SYS_SGMII1_PHY_ADDR 0x03
+#endif
+#define CONFIG_SYS_RGMII1_PHY_ADDR 0x01
+#define CONFIG_SYS_RGMII2_PHY_ADDR 0x02
+
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_ETHPRIME "FM1@DTSEC4"
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#ifdef CONFIG_T1042RDB_PI
+#define CONFIG_CMD_DATE
+#endif
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SETEXPR
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+
+#define CONFIG_BOOTDELAY 10 /*-1 disables auto-boot*/
+
+#define CONFIG_BAUDRATE 115200
+
+#define __USB_PHY_TYPE utmi
+
+#ifdef CONFIG_T1040RDB
+#define FDTFILE "t1040rdb/t1040rdb.dtb"
+#define RAMDISKFILE "t1040rdb/ramdisk.uboot"
+#elif CONFIG_T1042RDB_PI
+#define FDTFILE "t1040rdb_pi/t1040rdb_pi.dtb"
+#define RAMDISKFILE "t1040rdb_pi/ramdisk.uboot"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:bank_intlv=cs0_cs1;" \
+ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
+ "usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+ "netdev=eth0\0" \
+ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot && " \
+ "protect off $ubootaddr +$filesize && " \
+ "erase $ubootaddr +$filesize && " \
+ "cp.b $loadaddr $ubootaddr $filesize && " \
+ "protect on $ubootaddr +$filesize && " \
+ "cmp.b $loadaddr $ubootaddr $filesize\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=" __stringify(RAMDISKFILE) "\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=" __stringify(FDTFILE) "\0" \
+ "bdev=sda3\0" \
+ "c=ffe\0"
+
+#define CONFIG_LINUX \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "setenv ramdiskaddr 0x02000000;" \
+ "setenv fdtaddr 0x00c00000;" \
+ "setenv loadaddr 0x1000000;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_HDBOOT \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#endif
+
+#endif /* __CONFIG_H */
projects / oweals / u-boot.git / commitdiff