--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU111
+ *
+ * (C) Copyright 2017 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+ model = "ZynqMP ZCU111 RevA";
+ compatible = "xlnx,zynqmp-zcu111-revA", "xlnx,zynqmp-zcu111", "xlnx,zynqmp";
+
+ aliases {
+ ethernet0 = &gem3;
+ gpio0 = &gpio;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ mmc0 = &sdhci1;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ serial1 = &dcc;
+ spi0 = &qspi;
+ usb0 = &usb0;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+ /* Another 4GB connected to PL */
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+ sw19 {
+ label = "sw19";
+ gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_DOWN>;
+ gpio-key,wakeup;
+ autorepeat;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ heartbeat_led {
+ label = "heartbeat";
+ gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&dcc {
+ status = "okay";
+};
+
+&fpd_dma_chan1 {
+ status = "okay";
+};
+
+&fpd_dma_chan2 {
+ status = "okay";
+};
+
+&fpd_dma_chan3 {
+ status = "okay";
+};
+
+&fpd_dma_chan4 {
+ status = "okay";
+};
+
+&fpd_dma_chan5 {
+ status = "okay";
+};
+
+&fpd_dma_chan6 {
+ status = "okay";
+};
+
+&fpd_dma_chan7 {
+ status = "okay";
+};
+
+&fpd_dma_chan8 {
+ status = "okay";
+};
+
+&gem3 {
+ status = "okay";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ phy0: phy@c {
+ reg = <0xc>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tca6416_u22: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller; /* interrupt not connected */
+ #gpio-cells = <2>;
+ /*
+ * IRQ not connected
+ * Lines:
+ * 0 - MAX6643_OT_B
+ * 1 - MAX6643_FANFAIL_B
+ * 2 - MIO26_PMU_INPUT_LS
+ * 4 - SFP_SI5382_INT_ALM
+ * 5 - IIC_MUX_RESET_B
+ * 6 - GEM3_EXP_RESET_B
+ * 10 - FMCP_HSPC_PRSNT_M2C_B
+ * 11 - CLK_SPI_MUX_SEL0
+ * 12 - CLK_SPI_MUX_SEL1
+ * 16 - IRPS5401_ALERT_B
+ * 17 - INA226_PMBUS_ALERT
+ * 3, 7, 13-15 - not connected
+ */
+ };
+
+ i2c-mux@75 { /* u23 */
+ compatible = "nxp,pca9544";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /* PS_PMBUS */
+ /* PMBUS_ALERT done via pca9544 */
+ ina226@40 { /* u67 */
+ compatible = "ti,ina226";
+ reg = <0x40>;
+ shunt-resistor = <2000>;
+ };
+ ina226@41 { /* u59 */
+ compatible = "ti,ina226";
+ reg = <0x41>;
+ shunt-resistor = <5000>;
+ };
+ ina226@42 { /* u61 */
+ compatible = "ti,ina226";
+ reg = <0x42>;
+ shunt-resistor = <5000>;
+ };
+ ina226@43 { /* u60 */
+ compatible = "ti,ina226";
+ reg = <0x43>;
+ shunt-resistor = <5000>;
+ };
+ ina226@45 { /* u64 */
+ compatible = "ti,ina226";
+ reg = <0x45>;
+ shunt-resistor = <5000>;
+ };
+ ina226@46 { /* u69 */
+ compatible = "ti,ina226";
+ reg = <0x46>;
+ shunt-resistor = <2000>;
+ };
+ ina226@47 { /* u66 */
+ compatible = "ti,ina226";
+ reg = <0x47>;
+ shunt-resistor = <5000>;
+ };
+ ina226@48 { /* u65 */
+ compatible = "ti,ina226";
+ reg = <0x48>;
+ shunt-resistor = <5000>;
+ };
+ ina226@49 { /* u63 */
+ compatible = "ti,ina226";
+ reg = <0x49>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4a { /* u3 */
+ compatible = "ti,ina226";
+ reg = <0x4a>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4b { /* u71 */
+ compatible = "ti,ina226";
+ reg = <0x4b>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4c { /* u77 */
+ compatible = "ti,ina226";
+ reg = <0x4c>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4d { /* u73 */
+ compatible = "ti,ina226";
+ reg = <0x4d>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4e { /* u79 */
+ compatible = "ti,ina226";
+ reg = <0x4e>;
+ shunt-resistor = <5000>;
+ };
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* NC */
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ irps5401_43: irps54012@43 { /* IRPS5401 - u53 check these */
+ #clock-cells = <0>;
+ compatible = "infineon,irps5401";
+ reg = <0x43>;
+ };
+ irps5401_44: irps54012@44 { /* IRPS5401 - u55 */
+ #clock-cells = <0>;
+ compatible = "infineon,irps5401";
+ reg = <0x44>;
+ };
+ irps5401_45: irps54012@45 { /* IRPS5401 - u57 */
+ #clock-cells = <0>;
+ compatible = "infineon,irps5401";
+ reg = <0x45>;
+ };
+ /* u68 IR38064 +0 */
+ /* u70 IR38060 +1 */
+ /* u74 IR38060 +2 */
+ /* u75 IR38060 +6 */
+ /* J19 header too */
+
+ };
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ /* SYSMON */
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ i2c-mux@74 { /* u26 */
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /*
+ * IIC_EEPROM 1kB memory which uses 256B blocks
+ * where every block has different address.
+ * 0 - 256B address 0x54
+ * 256B - 512B address 0x55
+ * 512B - 768B address 0x56
+ * 768B - 1024B address 0x57
+ */
+ eeprom: eeprom@54 { /* u88 */
+ compatible = "atmel,24c08";
+ reg = <0x54>;
+ };
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ si5341: clock-generator@36 { /* SI5341 - u46 */
+ compatible = "si5341";
+ reg = <0x36>;
+ };
+
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ si570_1: clock-generator@5d { /* USER SI570 - u47 */
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ reg = <0x5d>;
+ temperature-stability = <50>;
+ factory-fout = <300000000>;
+ clock-frequency = <300000000>;
+ };
+ };
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ si570_2: clock-generator@5d { /* USER MGT SI570 - u49 */
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ reg = <0x5d>;
+ temperature-stability = <50>;
+ factory-fout = <156250000>;
+ clock-frequency = <148500000>;
+ };
+ };
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ si5328: clock-generator@69 { /* SI5328 - u48 */
+ compatible = "silabs,si5328";
+ reg = <0x69>;
+ };
+ };
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ sc18is603@2f { /* sc18is602 - u93 */
+ compatible = "nxp,sc18is603";
+ reg = <0x2f>;
+ /* 4 gpios for CS not handled by driver */
+ /*
+ * USB2ANY cable or
+ * LMK04208 - u90 or
+ * LMX2594 - u102 or
+ * LMX2594 - u103 or
+ * LMX2594 - u104
+ */
+ };
+ };
+ i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ /* FMC connector */
+ };
+ /* 7 NC */
+ };
+
+ i2c-mux@75 {
+ compatible = "nxp,pca9548"; /* u27 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /* FMCP_HSPC_IIC */
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* NC */
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ /* SYSMON */
+ };
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ /* DDR4 SODIMM */
+ dev@19 { /* u-boot detection FIXME */
+ compatible = "xxx";
+ reg = <0x19>;
+ };
+ dev@30 { /* u-boot detection */
+ compatible = "xxx";
+ reg = <0x30>;
+ };
+ dev@35 { /* u-boot detection */
+ compatible = "xxx";
+ reg = <0x35>;
+ };
+ dev@36 { /* u-boot detection */
+ compatible = "xxx";
+ reg = <0x36>;
+ };
+ dev@51 { /* u-boot detection - maybe SPD */
+ compatible = "xxx";
+ reg = <0x51>;
+ };
+ };
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ /* SFP3 */
+ };
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ /* SFP2 */
+ };
+ i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ /* SFP1 */
+ };
+ i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ /* SFP0 */
+ };
+ };
+};
+
+&qspi {
+ status = "okay";
+ is-dual = <1>;
+ flash@0 {
+ compatible = "m25p80"; /* 32MB */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ partition@qspi-fsbl-uboot { /* for testing purpose */
+ label = "qspi-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@qspi-linux { /* for testing purpose */
+ label = "qspi-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@qspi-device-tree { /* for testing purpose */
+ label = "qspi-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@qspi-rootfs { /* for testing purpose */
+ label = "qspi-rootfs";
+ reg = <0x620000 0x5E0000>;
+ };
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+ /* SATA OOB timing settings */
+ ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ phy-names = "sata-phy";
+ phys = <&lane3 PHY_TYPE_SATA 1 3 125000000>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+ status = "okay";
+ no-1-8-v;
+ xlnx,mio_bank = <1>;
+};
+
+&serdes {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+ status = "okay";
+};
+
+&dwc3_0 {
+ status = "okay";
+ dr_mode = "host";
+ snps,usb3_lpm_capable;
+ phy-names = "usb3-phy";
+ phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
+};
--- /dev/null
+CONFIG_ARM=y
+CONFIG_SYS_CONFIG_NAME="xilinx_zynqmp_zcu111"
+CONFIG_ARCH_ZYNQMP=y
+CONFIG_SYS_TEXT_BASE=0x8000000
+CONFIG_SYS_MALLOC_F_LEN=0x8000
+CONFIG_SPL=y
+CONFIG_IDENT_STRING=" Xilinx ZynqMP ZCU111"
+CONFIG_ZYNQMP_USB=y
+CONFIG_DEFAULT_DEVICE_TREE="zynqmp-zcu111-revA"
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_LOAD_FIT=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_SPL_OS_BOOT=y
+CONFIG_SPL_RAM_SUPPORT=y
+CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_ATF=y
+CONFIG_SYS_PROMPT="ZynqMP> "
+CONFIG_CMD_EEPROM=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DFU=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_FPGA_LOADBP=y
+CONFIG_CMD_FPGA_LOADP=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_TIMER=y
+CONFIG_CMD_EXT4_WRITE=y
+# CONFIG_SPL_ISO_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_EMBED=y
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SCSI_AHCI=y
+CONFIG_SATA_CEVA=y
+CONFIG_CLK_ZYNQMP=y
+CONFIG_DFU_RAM=y
+CONFIG_FPGA_XILINX=y
+CONFIG_FPGA_ZYNQMPPL=y
+CONFIG_DM_GPIO=y
+CONFIG_CMD_PCA953X=y
+CONFIG_SYS_I2C_ZYNQ=y
+CONFIG_ZYNQ_I2C0=y
+CONFIG_ZYNQ_I2C1=y
+CONFIG_MISC=y
+CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET=0x20
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ZYNQ=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_NATSEMI=y
+CONFIG_PHY_REALTEK=y
+CONFIG_PHY_TI=y
+CONFIG_PHY_VITESSE=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_PHY_GIGE=y
+CONFIG_ZYNQ_GEM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_DEBUG_UART_ZYNQ=y
+CONFIG_DEBUG_UART_BASE=0xff000000
+CONFIG_DEBUG_UART_CLOCK=100000000
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ZYNQ_SERIAL=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_XHCI_ZYNQMP=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GADGET=y
+CONFIG_USB_ULPI_VIEWPORT=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
--- /dev/null
+/*
+ * Configuration for Xilinx ZynqMP zcu111
+ *
+ * (C) Copyright 2017 Xilinx, Inc.
+ * Michal Simek <michal.simek@xilinx.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_ZYNQMP_ZCU111_H
+#define __CONFIG_ZYNQMP_ZCU111_H
+
+#define CONFIG_ZYNQ_SDHCI1
+#define CONFIG_SYS_I2C_MAX_HOPS 1
+#define CONFIG_SYS_NUM_I2C_BUSES 21
+#define CONFIG_SYS_I2C_BUSES { \
+ {0, {I2C_NULL_HOP} }, \
+ {0, {{I2C_MUX_PCA9544, 0x75, 0} } }, \
+ {0, {{I2C_MUX_PCA9544, 0x75, 1} } }, \
+ {0, {{I2C_MUX_PCA9544, 0x75, 2} } }, \
+ {0, {{I2C_MUX_PCA9544, 0x75, 3} } }, \
+ {1, {I2C_NULL_HOP} }, \
+ {1, {{I2C_MUX_PCA9548, 0x74, 0} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x74, 1} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x74, 2} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x74, 3} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x74, 4} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x74, 5} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x74, 6} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x75, 0} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x75, 1} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x75, 2} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x75, 3} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x75, 4} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x75, 5} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x75, 6} } }, \
+ {1, {{I2C_MUX_PCA9548, 0x75, 7} } }, \
+ }
+
+#define CONFIG_PCA953X
+
+#define CONFIG_ZYNQMP_XHCI_LIST {ZYNQMP_USB0_XHCI_BASEADDR}
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_ZYNQ_EEPROM_BUS 5
+#define CONFIG_ZYNQ_GEM_EEPROM_ADDR 0x54
+
+#include <configs/xilinx_zynqmp.h>
+
+#endif /* __CONFIG_ZYNQMP_ZCU111_H */
projects / oweals / u-boot.git / commitdiff