dtb-$(CONFIG_ARCH_MESON) += \
meson-gxbb-nanopi-k2.dtb \
meson-gxbb-odroidc2.dtb \
+ meson-gxbb-nanopi-k2.dtb \
meson-gxl-s905x-p212.dtb \
meson-gxl-s905x-libretech-cc.dtb \
meson-gxl-s905x-khadas-vim.dtb
with 2 GiB of RAM, Gigabit Ethernet, HDMI, 4 USB, micro-SD
slot, eMMC, IR receiver and a 40-pin GPIO header.
+config TARGET_NANOPI_K2
+ bool "NANOPI_K2"
+ help
+ NANOPI_K2 is a single board computer based on Meson GXBaby
+ with 2 GiB of RAM, Gigabit Ethernet,AP6212 Wifi, HDMI, 4 USB,
+ micro-SD slot, eMMC, IR receiver and a 40-pin GPIO header.
endif
if MESON_GXL
source "board/amlogic/odroid-c2/Kconfig"
+source "board/amlogic/nanopi-k2/Kconfig"
+
source "board/amlogic/p212/Kconfig"
source "board/amlogic/libretech-cc/Kconfig"
--- /dev/null
+if TARGET_NANOPI_K2
+
+config SYS_BOARD
+ default "nanopi-k2"
+
+config SYS_VENDOR
+ default "amlogic"
+
+config SYS_CONFIG_NAME
+ default "nanopi-k2"
+
+endif
--- /dev/null
+NANOPI-K2
+M: Neil Armstrong <narmstrong@baylibre.com>
+S: Maintained
+F: board/amlogic/nanopi-k2/
+F: include/configs/nanopi-k2.h
+F: configs/nanopi-k2_defconfig
--- /dev/null
+#
+# (C) Copyright 2018 Thomas McKahan
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := nanopi-k2.o
--- /dev/null
+U-Boot for NanoPi-K2
+====================
+
+NanoPi-K2 is a single board computer manufactured by FriendlyElec
+with the following specifications:
+
+ - Amlogic S905 ARM Cortex-A53 quad-core SoC @ 1.5GHz
+ - ARM Mali 450 GPU
+ - 2GB DDR3 SDRAM
+ - Gigabit Ethernet
+ - HDMI 2.0 4K/60Hz display
+ - 40-pin GPIO header
+ - 4 x USB 2.0 Host, 1 x USB OTG
+ - eMMC, microSD
+ - Infrared receiver
+
+Schematics are available on the manufacturer website.
+
+Currently the u-boot port supports the following devices:
+ - serial
+ - eMMC, microSD
+ - Ethernet
+
+u-boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make nanopi-k2_defconfig
+ > make
+
+Image creation
+==============
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+ > git clone https://github.com/BayLibre/u-boot.git -b libretech-cc amlogic-u-boot
+ > git clone https://github.com/friendlyarm/u-boot.git -b nanopi-k2-v2015.01 amlogic-u-boot
+ > cd amlogic-u-boot
+ > sed -i 's/aarch64-linux-gnu-/aarch64-none-elf-/' Makefile
+ > sed -i 's/arm-linux-/arm-none-eabi-/' arch/arm/cpu/armv8/gxb/firmware/scp_task/Makefile
+ > make nanopi-k2_defconfig
+ > make
+ > export FIPDIR=$PWD/fip
+
+Go back to mainline U-Boot source tree then :
+ > mkdir fip
+
+ > cp $FIPDIR/gxb/bl2.bin fip/
+ > cp $FIPDIR/gxb/acs.bin fip/
+ > cp $FIPDIR/gxb/bl21.bin fip/
+ > cp $FIPDIR/gxb/bl30.bin fip/
+ > cp $FIPDIR/gxb/bl301.bin fip/
+ > cp $FIPDIR/gxb/bl31.img fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > $FIPDIR/blx_fix.sh \
+ fip/bl30.bin \
+ fip/zero_tmp \
+ fip/bl30_zero.bin \
+ fip/bl301.bin \
+ fip/bl301_zero.bin \
+ fip/bl30_new.bin \
+ bl30
+
+ > $FIPDIR/fip_create \
+ --bl30 fip/bl30_new.bin \
+ --bl31 fip/bl31.img \
+ --bl33 fip/bl33.bin \
+ fip/fip.bin
+
+ > python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+ > $FIPDIR/blx_fix.sh \
+ fip/bl2_acs.bin \
+ fip/zero_tmp \
+ fip/bl2_zero.bin \
+ fip/bl21.bin \
+ fip/bl21_zero.bin \
+ fip/bl2_new.bin \
+ bl2
+
+ > cat fip/bl2_new.bin fip/fip.bin > fip/boot_new.bin
+
+ > $FIPDIR/gxb/aml_encrypt_gxb --bootsig \
+ --input fip/boot_new.bin
+ --output fip/u-boot.bin
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin of=$DEV conv=fsync,notrunc bs=512 seek=1
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2018 Thomas McKahan
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <environment.h>
+#include <asm/io.h>
+#include <asm/arch/gx.h>
+#include <asm/arch/sm.h>
+#include <asm/arch/eth.h>
+#include <asm/arch/mem.h>
+
+#define EFUSE_SN_OFFSET 20
+#define EFUSE_SN_SIZE 16
+#define EFUSE_MAC_OFFSET 52
+#define EFUSE_MAC_SIZE 6
+
+int board_init(void)
+{
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ u8 mac_addr[EFUSE_MAC_SIZE];
+ char serial[EFUSE_SN_SIZE];
+ ssize_t len;
+
+ meson_gx_eth_init(PHY_INTERFACE_MODE_RGMII, 0);
+
+ /* Reset PHY on GPIOZ_14 */
+ clrbits_le32(GX_GPIO_EN(3), BIT(14));
+ clrbits_le32(GX_GPIO_OUT(3), BIT(14));
+ mdelay(10);
+ setbits_le32(GX_GPIO_OUT(3), BIT(14));
+
+ if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
+ len = meson_sm_read_efuse(EFUSE_MAC_OFFSET,
+ mac_addr, EFUSE_MAC_SIZE);
+ if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr))
+ eth_env_set_enetaddr("ethaddr", mac_addr);
+ }
+
+ if (!env_get("serial#")) {
+ len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial,
+ EFUSE_SN_SIZE);
+ if (len == EFUSE_SN_SIZE)
+ env_set("serial#", serial);
+ }
+
+ return 0;
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ meson_gx_init_reserved_memory(blob);
+
+ return 0;
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_MESON_GXBB=y
+CONFIG_TARGET_NANOPI_K2=y
+CONFIG_DEBUG_UART_BASE=0xc81004c0
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" nanopi-k2"
+CONFIG_DEFAULT_DEVICE_TREE="meson-gxbb-nanopi-k2"
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MESON=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_GXBB=y
+CONFIG_DEBUG_UART_MESON=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_OF_LIBFDT_OVERLAY=y
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuration for NANOPI-K2
+ * (C) Copyright 2018 Thomas McKahan
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MISC_INIT_R
+
+/* Serial setup */
+
+#define MESON_FDTFILE_SETTING "fdtfile=amlogic/meson-gxbb-nanopi-k2.dtb\0"
+
+#include <configs/meson-gx-common.h>
+
+#endif /* __CONFIG_H */
projects / oweals / u-boot.git / commitdiff