eeprom: Zap CONFIG_SYS_EEPROM_X40430
authorMarek Vasut <marex@denx.de>
Tue, 10 Nov 2015 19:53:20 +0000 (20:53 +0100)
committerTom Rini <trini@konsulko.com>
Sun, 22 Nov 2015 02:50:21 +0000 (21:50 -0500)
Now that the only user of CONFIG_SYS_EEPROM_X40430 was removed,
remove this unused code from cmd_eeprom.c

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
common/cmd_eeprom.c

index 0b59bea01dd99b2ef660686b8ec8cc9f175e13a3..266f954e6f3623e6acb356707d4f162a7184b827 100644 (file)
 #define        CONFIG_SYS_I2C_SPEED    50000
 #endif
 
-/* Maximum number of times to poll for acknowledge after write */
-#if defined(CONFIG_SYS_EEPROM_X40430)
-#define MAX_ACKNOWLEDGE_POLLS  10
-#endif
-
 /*
  * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 2 (16-bit EEPROM address) offset is
  *   0x000nxxxx for EEPROM address selectors at n, offset xxxx in EEPROM.
@@ -141,14 +136,6 @@ int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cn
        unsigned blk_off;
        int rcode = 0;
 
-#if defined(CONFIG_SYS_EEPROM_X40430)
-       uchar   contr_r_addr[2];
-       uchar   addr_void[2];
-       uchar   contr_reg[2];
-       uchar   ctrl_reg_v;
-       int     i;
-#endif
-
 #if defined(CONFIG_SYS_EEPROM_WREN)
        eeprom_write_enable (dev_addr,1);
 #endif
@@ -213,88 +200,7 @@ int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cn
 #if defined(CONFIG_SPI) && !defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
                spi_write (addr, alen, buffer, len);
 #else
-#if defined(CONFIG_SYS_EEPROM_X40430)
-               /* Get the value of the control register.
-                * Set current address (internal pointer in the x40430)
-                * to 0x1ff.
-                */
-               contr_r_addr[0] = 9;
-               contr_r_addr[1] = 0xff;
-               addr_void[0]    = 0;
-               addr_void[1]    = addr[1];
-#ifdef CONFIG_SYS_I2C_EEPROM_ADDR
-               contr_r_addr[0] |= CONFIG_SYS_I2C_EEPROM_ADDR;
-               addr_void[0]    |= CONFIG_SYS_I2C_EEPROM_ADDR;
-#endif
-               contr_reg[0] = 0xff;
-               if (i2c_read (contr_r_addr[0], contr_r_addr[1], 1, contr_reg, 1) != 0) {
-                       rcode = 1;
-               }
-               ctrl_reg_v = contr_reg[0];
 
-               /* Are any of the eeprom blocks write protected?
-                */
-               if (ctrl_reg_v & 0x18) {
-                       ctrl_reg_v &= ~0x18;   /* reset block protect bits  */
-                       ctrl_reg_v |=  0x02;   /* set write enable latch    */
-                       ctrl_reg_v &= ~0x04;   /* clear RWEL                */
-
-                       /* Set write enable latch.
-                        */
-                       contr_reg[0] = 0x02;
-                       if (i2c_write (contr_r_addr[0], 0xff, 1, contr_reg, 1) != 0) {
-                               rcode = 1;
-                       }
-
-                       /* Set register write enable latch.
-                        */
-                       contr_reg[0] = 0x06;
-                       if (i2c_write (contr_r_addr[0], 0xFF, 1, contr_reg, 1) != 0) {
-                               rcode = 1;
-                       }
-
-                       /* Modify ctrl register.
-                        */
-                       contr_reg[0] = ctrl_reg_v;
-                       if (i2c_write (contr_r_addr[0], 0xFF, 1, contr_reg, 1) != 0) {
-                               rcode = 1;
-                       }
-
-                       /* The write (above) is an operation on NV memory.
-                        * These can take some time (~5ms), and the device
-                        * will not respond to further I2C messages till
-                        * it's completed the write.
-                        * So poll device for an I2C acknowledge.
-                        * When we get one we know we can continue with other
-                        * operations.
-                        */
-                       contr_reg[0] = 0;
-                       for (i = 0; i < MAX_ACKNOWLEDGE_POLLS; i++) {
-                               if (i2c_read (addr_void[0], addr_void[1], 1, contr_reg, 1) == 0)
-                                       break;  /* got ack */
-#if defined(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS)
-                               udelay(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
-#endif
-                       }
-                       if (i == MAX_ACKNOWLEDGE_POLLS) {
-                               puts ("EEPROM poll acknowledge failed\n");
-                               rcode = 1;
-                       }
-               }
-
-               /* Is the write enable latch on?.
-                */
-               else if (!(ctrl_reg_v & 0x02)) {
-                       /* Set write enable latch.
-                        */
-                       contr_reg[0] = 0x02;
-                       if (i2c_write (contr_r_addr[0], 0xFF, 1, contr_reg, 1) != 0) {
-                              rcode = 1;
-                       }
-               }
-               /* Write is enabled ... now write eeprom value.
-                */
-#endif
 #if defined(CONFIG_SYS_I2C_EEPROM_BUS)
                i2c_set_bus_num(CONFIG_SYS_I2C_EEPROM_BUS);
 #endif