Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of Flash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)
Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to web interface:
[V1] http://192.168.0.1
[V2] http://192.168.0.254
Default user is "admin" & password is "admin".
On V2, there is no DHCP server running by default, so remember to set
IP manually.
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware:
[V1] "*.factory.bin"
[V2] "*.factory-us.bin" or "*.factory-eu.bin" for eu model
Web interface may complain if filename is too long. In such case,
rename .bin to something shorter.
- Click upgrade
Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
Serial Configuration 115200 8n1
- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
(IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
(e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
(e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
(e.g bootm 0x9f020000)
Notes:
When porting from ar71xx target to ath79, I found out that on V2,
reset button is on GPIO12 and active low, instead of GPIO11 and
active high. By cross-flashing V1 firmware to V2, I confirmed
the same is true for V1.
Also according to manual of V1, this one also has green
LED instead of blue - both of those issues were fixed accordingly.
The MAC address assignment has been checked with OEM firmware.
Installation manual based on ar71xx support by Thomas Roberts
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit message, add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit
7e513136c63108bf55b38be4d2b65aa00b0d2b26)
tplink,tl-wa901nd-v4|\
tplink,tl-wa901nd-v5|\
tplink,tl-wr703n|\
+ tplink,tl-wr802n-v1|\
+ tplink,tl-wr802n-v2|\
ubnt,bullet-m|\
ubnt,bullet-m-xw|\
ubnt,lap-120|\
tplink,archer-c58-v1|\
tplink,archer-c59-v1|\
tplink,archer-c7-v4|\
-tplink,archer-c7-v5)
+tplink,archer-c7-v5|\
+tplink,tl-wr802n-v2)
migrate_leds "^$boardonly:=tp-link:"
;;
tplink,archer-c7-v2|\
tplink,tl-wdr3600-v1|\
tplink,tl-wdr4300-v1|\
tplink,tl-wdr4300-v1-il|\
-tplink,tl-wdr4310-v1)
+tplink,tl-wdr4310-v1|\
+tplink,tl-wr802n-v1)
migrate_leds ":blue:=:green:"
;;
wd,mynet-n750)
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "qca9533_tplink_tl-wr802n.dtsi"
+
+/ {
+ model = "TP-Link TL-WR802N v1";
+ compatible = "tplink,tl-wr802n-v1", "qca,qca9533";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "qca9533_tplink_tl-wr802n.dtsi"
+
+/ {
+ model = "TP-Link TL-WR802N v2";
+ compatible = "tplink,tl-wr802n-v2", "qca,qca9533";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca953x.dtsi"
+
+/ {
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ aliases {
+ led-boot = &led_system;
+ led-failsafe = &led_system;
+ led-running = &led_system;
+ led-upgrade = &led_system;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_system: system {
+ label = "tp-link:green:system";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&uart {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+
+ num-cs = <1>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uboot: partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x020000>;
+ read-only;
+ };
+
+ partition@20000 {
+ label = "firmware";
+ reg = <0x020000 0x3d0000>;
+ compatible = "tplink,firmware";
+ };
+
+ art: partition@3f0000 {
+ label = "art";
+ reg = <0x3f0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&uboot 0x1fc00>;
+};
+
+ð0 {
+ status = "okay";
+
+ phy-handle = <&swphy4>;
+
+ mtd-mac-address = <&uboot 0x1fc00>;
+ mtd-mac-address-increment = <1>;
+};
+
+ð1 {
+ compatible = "syscon", "simple-mfd";
+};
endef
TARGET_DEVICES += tplink_tl-wr743nd-v1
+define Device/tplink_tl-wr802n-v1
+ $(Device/tplink-4mlzma)
+ ATH_SOC := qca9533
+ DEVICE_TITLE := TP-Link TL-WR802N v1
+ TPLINK_HWID := 0x08020001
+ SUPPORTED_DEVICES += tl-wr802n-v1
+endef
+TARGET_DEVICES += tplink_tl-wr802n-v1
+
+define Device/tplink_tl-wr802n-v2
+ $(Device/tplink-4mlzma)
+ ATH_SOC := qca9533
+ DEVICE_TITLE := TP-Link TL-WR802N v2
+ TPLINK_HWID := 0x08020002
+ TPLINK_HWREV := 2
+ SUPPORTED_DEVICES += tl-wr802n-v2
+ IMAGES += factory-us.bin factory-eu.bin
+ IMAGE/factory-us.bin := append-rootfs | mktplinkfw factory -C US
+ IMAGE/factory-eu.bin := append-rootfs | mktplinkfw factory -C EU
+endef
+TARGET_DEVICES += tplink_tl-wr802n-v2
+
define Device/tplink_tl-wr841-v5
$(Device/tplink-4m)
ATH_SOC := ar7240
projects / oweals / openwrt.git / commitdiff