* TODO: need more info?
*/
+/**
+ * DOC: Frame transmission/registration support
+ *
+ * Frame transmission and registration support exists to allow userspace
+ * management entities such as wpa_supplicant react to management frames
+ * that are not being handled by the kernel. This includes, for example,
+ * certain classes of action frames that cannot be handled in the kernel
+ * for various reasons.
+ *
+ * Frame registration is done on a per-interface basis and registrations
+ * cannot be removed other than by closing the socket. It is possible to
+ * specify a registration filter to register, for example, only for a
+ * certain type of action frame. In particular with action frames, those
+ * that userspace registers for will not be returned as unhandled by the
+ * driver, so that the registered application has to take responsibility
+ * for doing that.
+ *
+ * The type of frame that can be registered for is also dependent on the
+ * driver and interface type. The frame types are advertised in wiphy
+ * attributes so applications know what to expect.
+ *
+ * NOTE: When an interface changes type while registrations are active,
+ * these registrations are ignored until the interface type is
+ * changed again. This means that changing the interface type can
+ * lead to a situation that couldn't otherwise be produced, but
+ * any such registrations will be dormant in the sense that they
+ * will not be serviced, i.e. they will not receive any frames.
+ *
+ * Frame transmission allows userspace to send for example the required
+ * responses to action frames. It is subject to some sanity checking,
+ * but many frames can be transmitted. When a frame was transmitted, its
+ * status is indicated to the sending socket.
+ *
+ * For more technical details, see the corresponding command descriptions
+ * below.
+ */
+
/**
* enum nl80211_commands - supported nl80211 commands
*
* auth and assoc steps. For this, you need to specify the SSID in a
* %NL80211_ATTR_SSID attribute, and can optionally specify the association
* IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC,
- * %NL80211_ATTR_WIPHY_FREQ and %NL80211_ATTR_CONTROL_PORT.
+ * %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
+ * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and
+ * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT.
* It is also sent as an event, with the BSSID and response IEs when the
* connection is established or failed to be established. This can be
* determined by the STATUS_CODE attribute.
* channel for the specified amount of time. This can be used to do
* off-channel operations like transmit a Public Action frame and wait for
* a response while being associated to an AP on another channel.
- * %NL80211_ATTR_WIPHY or %NL80211_ATTR_IFINDEX is used to specify which
- * radio is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
+ * %NL80211_ATTR_IFINDEX is used to specify which interface (and thus
+ * radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
* frequency for the operation and %NL80211_ATTR_WIPHY_CHANNEL_TYPE may be
* optionally used to specify additional channel parameters.
* %NL80211_ATTR_DURATION is used to specify the duration in milliseconds
* rate selection. %NL80211_ATTR_IFINDEX is used to specify the interface
* and @NL80211_ATTR_TX_RATES the set of allowed rates.
*
- * @NL80211_CMD_REGISTER_ACTION: Register for receiving certain action frames
- * (via @NL80211_CMD_ACTION) for processing in userspace. This command
- * requires an interface index and a match attribute containing the first
- * few bytes of the frame that should match, e.g. a single byte for only
- * a category match or four bytes for vendor frames including the OUI.
- * The registration cannot be dropped, but is removed automatically
- * when the netlink socket is closed. Multiple registrations can be made.
- * @NL80211_CMD_ACTION: Action frame TX request and RX notification. This
- * command is used both as a request to transmit an Action frame and as an
- * event indicating reception of an Action frame that was not processed in
+ * @NL80211_CMD_REGISTER_FRAME: Register for receiving certain mgmt frames
+ * (via @NL80211_CMD_FRAME) for processing in userspace. This command
+ * requires an interface index, a frame type attribute (optional for
+ * backward compatibility reasons, if not given assumes action frames)
+ * and a match attribute containing the first few bytes of the frame
+ * that should match, e.g. a single byte for only a category match or
+ * four bytes for vendor frames including the OUI. The registration
+ * cannot be dropped, but is removed automatically when the netlink
+ * socket is closed. Multiple registrations can be made.
+ * @NL80211_CMD_REGISTER_ACTION: Alias for @NL80211_CMD_REGISTER_FRAME for
+ * backward compatibility
+ * @NL80211_CMD_FRAME: Management frame TX request and RX notification. This
+ * command is used both as a request to transmit a management frame and
+ * as an event indicating reception of a frame that was not processed in
* kernel code, but is for us (i.e., which may need to be processed in a
* user space application). %NL80211_ATTR_FRAME is used to specify the
* frame contents (including header). %NL80211_ATTR_WIPHY_FREQ (and
* operational channel). When called, this operation returns a cookie
* (%NL80211_ATTR_COOKIE) that will be included with the TX status event
* pertaining to the TX request.
- * @NL80211_CMD_ACTION_TX_STATUS: Report TX status of an Action frame
- * transmitted with %NL80211_CMD_ACTION. %NL80211_ATTR_COOKIE identifies
+ * @NL80211_CMD_ACTION: Alias for @NL80211_CMD_FRAME for backward compatibility.
+ * @NL80211_CMD_FRAME_TX_STATUS: Report TX status of a management frame
+ * transmitted with %NL80211_CMD_FRAME. %NL80211_ATTR_COOKIE identifies
* the TX command and %NL80211_ATTR_FRAME includes the contents of the
* frame. %NL80211_ATTR_ACK flag is included if the recipient acknowledged
* the frame.
+ * @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for
+ * backward compatibility.
* @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command
* is used to configure connection quality monitoring notification trigger
* levels.
* of any other interfaces, and other interfaces will again take
* precedence when they are used.
*
+ * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
+ *
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
NL80211_CMD_SET_TX_BITRATE_MASK,
- NL80211_CMD_REGISTER_ACTION,
- NL80211_CMD_ACTION,
- NL80211_CMD_ACTION_TX_STATUS,
+ NL80211_CMD_REGISTER_FRAME,
+ NL80211_CMD_REGISTER_ACTION = NL80211_CMD_REGISTER_FRAME,
+ NL80211_CMD_FRAME,
+ NL80211_CMD_ACTION = NL80211_CMD_FRAME,
+ NL80211_CMD_FRAME_TX_STATUS,
+ NL80211_CMD_ACTION_TX_STATUS = NL80211_CMD_FRAME_TX_STATUS,
NL80211_CMD_SET_POWER_SAVE,
NL80211_CMD_GET_POWER_SAVE,
NL80211_CMD_NOTIFY_CQM,
NL80211_CMD_SET_CHANNEL,
+ NL80211_CMD_SET_WDS_PEER,
/* add new commands above here */
* request, the driver will assume that the port is unauthorized until
* authorized by user space. Otherwise, port is marked authorized by
* default in station mode.
+ * @NL80211_ATTR_CONTROL_PORT_ETHERTYPE: A 16-bit value indicating the
+ * ethertype that will be used for key negotiation. It can be
+ * specified with the associate and connect commands. If it is not
+ * specified, the value defaults to 0x888E (PAE, 802.1X). This
+ * attribute is also used as a flag in the wiphy information to
+ * indicate that protocols other than PAE are supported.
+ * @NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT: When included along with
+ * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, indicates that the custom
+ * ethertype frames used for key negotiation must not be encrypted.
*
* @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
* We recommend using nested, driver-specific attributes within this.
* is used with %NL80211_CMD_SET_TX_BITRATE_MASK.
*
* @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain
- * at least one byte, currently used with @NL80211_CMD_REGISTER_ACTION.
+ * at least one byte, currently used with @NL80211_CMD_REGISTER_FRAME.
+ * @NL80211_ATTR_FRAME_TYPE: A u16 indicating the frame type/subtype for the
+ * @NL80211_CMD_REGISTER_FRAME command.
+ * @NL80211_ATTR_TX_FRAME_TYPES: wiphy capability attribute, which is a
+ * nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
+ * information about which frame types can be transmitted with
+ * %NL80211_CMD_FRAME.
+ * @NL80211_ATTR_RX_FRAME_TYPES: wiphy capability attribute, which is a
+ * nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
+ * information about which frame types can be registered for RX.
*
* @NL80211_ATTR_ACK: Flag attribute indicating that the frame was
* acknowledged by the recipient.
* @NL80211_ATTR_AP_ISOLATE: (AP mode) Do not forward traffic between stations
* connected to this BSS.
*
+ * @NL80211_ATTR_WIPHY_TX_POWER_SETTING: Transmit power setting type. See
+ * &enum nl80211_tx_power_setting for possible values.
+ * @NL80211_ATTR_WIPHY_TX_POWER_LEVEL: Transmit power level in signed mBm units.
+ * This is used in association with @NL80211_ATTR_WIPHY_TX_POWER_SETTING
+ * for non-automatic settings.
+ *
+ * @NL80211_ATTR_SUPPORT_IBSS_RSN: The device supports IBSS RSN, which mostly
+ * means support for per-station GTKs.
+ *
+ * @NL80211_ATTR_MCAST_RATE: Multicast tx rate (in 100 kbps) for IBSS
+ *
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
NL80211_ATTR_AP_ISOLATE,
+ NL80211_ATTR_WIPHY_TX_POWER_SETTING,
+ NL80211_ATTR_WIPHY_TX_POWER_LEVEL,
+
+ NL80211_ATTR_TX_FRAME_TYPES,
+ NL80211_ATTR_RX_FRAME_TYPES,
+ NL80211_ATTR_FRAME_TYPE,
+
+ NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
+ NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT,
+
+ NL80211_ATTR_SUPPORT_IBSS_RSN,
+
+ NL80211_ATTR_MCAST_RATE,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
* @NL80211_IFTYPE_WDS: wireless distribution interface
* @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames
* @NL80211_IFTYPE_MESH_POINT: mesh point
+ * @NL80211_IFTYPE_P2P_CLIENT: P2P client
+ * @NL80211_IFTYPE_P2P_GO: P2P group owner
* @NL80211_IFTYPE_MAX: highest interface type number currently defined
- * @__NL80211_IFTYPE_AFTER_LAST: internal use
+ * @NUM_NL80211_IFTYPES: number of defined interface types
*
* These values are used with the %NL80211_ATTR_IFTYPE
* to set the type of an interface.
NL80211_IFTYPE_WDS,
NL80211_IFTYPE_MONITOR,
NL80211_IFTYPE_MESH_POINT,
+ NL80211_IFTYPE_P2P_CLIENT,
+ NL80211_IFTYPE_P2P_GO,
/* keep last */
- __NL80211_IFTYPE_AFTER_LAST,
- NL80211_IFTYPE_MAX = __NL80211_IFTYPE_AFTER_LAST - 1
+ NUM_NL80211_IFTYPES,
+ NL80211_IFTYPE_MAX = NUM_NL80211_IFTYPES - 1
};
/**
* Station flags. When a station is added to an AP interface, it is
* assumed to be already associated (and hence authenticated.)
*
+ * @__NL80211_STA_FLAG_INVALID: attribute number 0 is reserved
* @NL80211_STA_FLAG_AUTHORIZED: station is authorized (802.1X)
* @NL80211_STA_FLAG_SHORT_PREAMBLE: station is capable of receiving frames
* with short barker preamble
* @NL80211_STA_FLAG_WME: station is WME/QoS capable
* @NL80211_STA_FLAG_MFP: station uses management frame protection
+ * @NL80211_STA_FLAG_MAX: highest station flag number currently defined
+ * @__NL80211_STA_FLAG_AFTER_LAST: internal use
*/
enum nl80211_sta_flags {
__NL80211_STA_FLAG_INVALID,
* @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station)
* @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (u32, to this
* station)
+ * @NL80211_STA_INFO_TX_RETRIES: total retries (u32, to this station)
+ * @NL80211_STA_INFO_TX_FAILED: total failed packets (u32, to this station)
*/
enum nl80211_sta_info {
__NL80211_STA_INFO_INVALID,
NL80211_STA_INFO_TX_BITRATE,
NL80211_STA_INFO_RX_PACKETS,
NL80211_STA_INFO_TX_PACKETS,
+ NL80211_STA_INFO_TX_RETRIES,
+ NL80211_STA_INFO_TX_FAILED,
/* keep last */
__NL80211_STA_INFO_AFTER_LAST,
* information about a mesh path.
*
* @__NL80211_MPATH_INFO_INVALID: attribute number 0 is reserved
- * @NL80211_ATTR_MPATH_FRAME_QLEN: number of queued frames for this destination
- * @NL80211_ATTR_MPATH_SN: destination sequence number
- * @NL80211_ATTR_MPATH_METRIC: metric (cost) of this mesh path
- * @NL80211_ATTR_MPATH_EXPTIME: expiration time for the path, in msec from now
- * @NL80211_ATTR_MPATH_FLAGS: mesh path flags, enumerated in
+ * @NL80211_MPATH_INFO_FRAME_QLEN: number of queued frames for this destination
+ * @NL80211_MPATH_INFO_SN: destination sequence number
+ * @NL80211_MPATH_INFO_METRIC: metric (cost) of this mesh path
+ * @NL80211_MPATH_INFO_EXPTIME: expiration time for the path, in msec from now
+ * @NL80211_MPATH_INFO_FLAGS: mesh path flags, enumerated in
* &enum nl80211_mpath_flags;
- * @NL80211_ATTR_MPATH_DISCOVERY_TIMEOUT: total path discovery timeout, in msec
- * @NL80211_ATTR_MPATH_DISCOVERY_RETRIES: mesh path discovery retries
+ * @NL80211_MPATH_INFO_DISCOVERY_TIMEOUT: total path discovery timeout, in msec
+ * @NL80211_MPATH_INFO_DISCOVERY_RETRIES: mesh path discovery retries
+ * @NL80211_MPATH_INFO_MAX: highest mesh path information attribute number
+ * currently defind
+ * @__NL80211_MPATH_INFO_AFTER_LAST: internal use
*/
enum nl80211_mpath_info {
__NL80211_MPATH_INFO_INVALID,
* @NL80211_BAND_ATTR_HT_CAPA: HT capabilities, as in the HT information IE
* @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n
* @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n
+ * @NL80211_BAND_ATTR_MAX: highest band attribute currently defined
+ * @__NL80211_BAND_ATTR_AFTER_LAST: internal use
*/
enum nl80211_band_attr {
__NL80211_BAND_ATTR_INVALID,
/**
* enum nl80211_frequency_attr - frequency attributes
+ * @__NL80211_FREQUENCY_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz
* @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current
* regulatory domain.
* on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm
* (100 * dBm).
+ * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
+ * currently defined
+ * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
*/
enum nl80211_frequency_attr {
__NL80211_FREQUENCY_ATTR_INVALID,
/**
* enum nl80211_bitrate_attr - bitrate attributes
+ * @__NL80211_BITRATE_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_BITRATE_ATTR_RATE: Bitrate in units of 100 kbps
* @NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE: Short preamble supported
* in 2.4 GHz band.
+ * @NL80211_BITRATE_ATTR_MAX: highest bitrate attribute number
+ * currently defined
+ * @__NL80211_BITRATE_ATTR_AFTER_LAST: internal use
*/
enum nl80211_bitrate_attr {
__NL80211_BITRATE_ATTR_INVALID,
/**
* enum nl80211_reg_rule_attr - regulatory rule attributes
+ * @__NL80211_REG_RULE_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_ATTR_REG_RULE_FLAGS: a set of flags which specify additional
* considerations for a given frequency range. These are the
* &enum nl80211_reg_rule_flags.
* If you don't have one then don't send this.
* @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for
* a given frequency range. The value is in mBm (100 * dBm).
+ * @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number
+ * currently defined
+ * @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use
*/
enum nl80211_reg_rule_attr {
__NL80211_REG_RULE_ATTR_INVALID,
* @__NL80211_SURVEY_INFO_INVALID: attribute number 0 is reserved
* @NL80211_SURVEY_INFO_FREQUENCY: center frequency of channel
* @NL80211_SURVEY_INFO_NOISE: noise level of channel (u8, dBm)
+ * @NL80211_SURVEY_INFO_IN_USE: channel is currently being used
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME: amount of time (in ms) that the radio
+ * spent on this channel
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY: amount of the time the primary
+ * channel was sensed busy (either due to activity or energy detect)
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY: amount of time the extension
+ * channel was sensed busy
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_RX: amount of time the radio spent
+ * receiving data
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_TX: amount of time the radio spent
+ * transmitting data
+ * @NL80211_SURVEY_INFO_MAX: highest survey info attribute number
+ * currently defined
+ * @__NL80211_SURVEY_INFO_AFTER_LAST: internal use
*/
enum nl80211_survey_info {
__NL80211_SURVEY_INFO_INVALID,
NL80211_SURVEY_INFO_FREQUENCY,
NL80211_SURVEY_INFO_NOISE,
+ NL80211_SURVEY_INFO_IN_USE,
+ NL80211_SURVEY_INFO_CHANNEL_TIME,
+ NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY,
+ NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY,
+ NL80211_SURVEY_INFO_CHANNEL_TIME_RX,
+ NL80211_SURVEY_INFO_CHANNEL_TIME_TX,
/* keep last */
__NL80211_SURVEY_INFO_AFTER_LAST,
* enum nl80211_bss - netlink attributes for a BSS
*
* @__NL80211_BSS_INVALID: invalid
+ * @NL80211_BSS_BSSID: BSSID of the BSS (6 octets)
* @NL80211_BSS_FREQUENCY: frequency in MHz (u32)
* @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64)
* @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16)
/**
* enum nl80211_bss_status - BSS "status"
+ * @NL80211_BSS_STATUS_AUTHENTICATED: Authenticated with this BSS.
+ * @NL80211_BSS_STATUS_ASSOCIATED: Associated with this BSS.
+ * @NL80211_BSS_STATUS_IBSS_JOINED: Joined to this IBSS.
+ *
+ * The BSS status is a BSS attribute in scan dumps, which
+ * indicates the status the interface has wrt. this BSS.
*/
enum nl80211_bss_status {
NL80211_BSS_STATUS_AUTHENTICATED,
* @NL80211_KEYTYPE_GROUP: Group (broadcast/multicast) key
* @NL80211_KEYTYPE_PAIRWISE: Pairwise (unicast/individual) key
* @NL80211_KEYTYPE_PEERKEY: PeerKey (DLS)
+ * @NUM_NL80211_KEYTYPES: number of defined key types
*/
enum nl80211_key_type {
NL80211_KEYTYPE_GROUP,
NL80211_KEYTYPE_PAIRWISE,
NL80211_KEYTYPE_PEERKEY,
+
+ NUM_NL80211_KEYTYPES
};
/**
* CCMP keys, each six bytes in little endian
* @NL80211_KEY_DEFAULT: flag indicating default key
* @NL80211_KEY_DEFAULT_MGMT: flag indicating default management key
+ * @NL80211_KEY_TYPE: the key type from enum nl80211_key_type, if not
+ * specified the default depends on whether a MAC address was
+ * given with the command using the key or not (u32)
* @__NL80211_KEY_AFTER_LAST: internal
* @NL80211_KEY_MAX: highest key attribute
*/
NL80211_KEY_SEQ,
NL80211_KEY_DEFAULT,
NL80211_KEY_DEFAULT_MGMT,
+ NL80211_KEY_TYPE,
/* keep last */
__NL80211_KEY_AFTER_LAST,
/**
* enum nl80211_band - Frequency band
- * @NL80211_BAND_2GHZ - 2.4 GHz ISM band
- * @NL80211_BAND_5GHZ - around 5 GHz band (4.9 - 5.7 GHz)
+ * @NL80211_BAND_2GHZ: 2.4 GHz ISM band
+ * @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz)
*/
enum nl80211_band {
NL80211_BAND_2GHZ,
/**
* enum nl80211_cqm_rssi_threshold_event - RSSI threshold event
- * @NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW - The RSSI level is lower than the
+ * @NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW: The RSSI level is lower than the
* configured threshold
- * @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH - The RSSI is higher than the
+ * @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH: The RSSI is higher than the
* configured threshold
*/
enum nl80211_cqm_rssi_threshold_event {
NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH,
};
+
+/**
+ * enum nl80211_tx_power_setting - TX power adjustment
+ * @NL80211_TX_POWER_AUTOMATIC: automatically determine transmit power
+ * @NL80211_TX_POWER_LIMITED: limit TX power by the mBm parameter
+ * @NL80211_TX_POWER_FIXED: fix TX power to the mBm parameter
+ */
+enum nl80211_tx_power_setting {
+ NL80211_TX_POWER_AUTOMATIC,
+ NL80211_TX_POWER_LIMITED,
+ NL80211_TX_POWER_FIXED,
+};
+
#endif /* __LINUX_NL80211_H */
return -1;
}
-int nl80211_get_noise(const char *ifname, int *buf)
+static int nl80211_get_noise_cb(struct nl_msg *msg, void *arg)
{
- int rv = -1;
- struct nl80211_msg_conveyor *req, *res;
+ int8_t *noise = arg;
+ struct genlmsghdr *gnlh = nlmsg_data(nlmsg_hdr(msg));
+ struct nlattr *tb[NL80211_ATTR_MAX + 1];
struct nlattr *si[NL80211_SURVEY_INFO_MAX + 1];
static struct nla_policy sp[NL80211_SURVEY_INFO_MAX + 1] = {
[NL80211_SURVEY_INFO_NOISE] = { .type = NLA_U8 },
};
+ nla_parse(tb, NL80211_ATTR_MAX, genlmsg_attrdata(gnlh, 0),
+ genlmsg_attrlen(gnlh, 0), NULL);
+
+ if (!tb[NL80211_ATTR_SURVEY_INFO])
+ return NL_SKIP;
+
+ if (nla_parse_nested(si, NL80211_SURVEY_INFO_MAX,
+ tb[NL80211_ATTR_SURVEY_INFO], sp))
+ return NL_SKIP;
+
+ if (!si[NL80211_SURVEY_INFO_NOISE])
+ return NL_SKIP;
+
+ if (!*noise || si[NL80211_SURVEY_INFO_IN_USE])
+ *noise = (int8_t)nla_get_u8(si[NL80211_SURVEY_INFO_NOISE]);
+
+ return NL_SKIP;
+}
+
+
+int nl80211_get_noise(const char *ifname, int *buf)
+{
+ int8_t noise;
+ struct nl80211_msg_conveyor *req;
+
req = nl80211_msg(ifname, NL80211_CMD_GET_SURVEY, NLM_F_DUMP);
- if( req )
+ if (req)
{
- res = nl80211_send(req);
- if( res )
+ noise = 0;
+
+ nl80211_cb(req, nl80211_get_noise_cb, &noise);
+ nl80211_send(req);
+ nl80211_free(req);
+
+ if (noise)
{
- if( res->attr[NL80211_ATTR_SURVEY_INFO] )
- {
- if( !nla_parse_nested(si, NL80211_SURVEY_INFO_MAX,
- res->attr[NL80211_ATTR_SURVEY_INFO], sp) &&
- si[NL80211_SURVEY_INFO_NOISE] )
- {
- *buf = (int8_t)nla_get_u8(si[NL80211_SURVEY_INFO_NOISE]);
- rv = 0;
- }
- }
- nl80211_free(res);
+ *buf = noise;
+ return 0;
}
- nl80211_free(req);
}
- return rv;
+ return -1;
}
int nl80211_get_quality(const char *ifname, int *buf)
/* Hostapd */
if( (res = nl80211_hostapd_info(ifname)) )
{
- if( (val = nl80211_getval(ifname, res, "auth_algs")) && (val > 0) )
- {
+ if( (val = nl80211_getval(ifname, res, "wpa")) != NULL )
+ c->wpa_version = atoi(val);
+
+ val = nl80211_getval(ifname, res, "wpa_key_mgmt");
+
+ if( !val || strstr(val, "PSK") )
+ c->auth_suites |= IWINFO_KMGMT_PSK;
+
+ if( val && strstr(val, "EAP") )
+ c->auth_suites |= IWINFO_KMGMT_8021x;
+
+ if( val && strstr(val, "NONE") )
c->auth_suites |= IWINFO_KMGMT_NONE;
+ if( (val = nl80211_getval(ifname, res, "wpa_pairwise")) != NULL )
+ {
+ if( strstr(val, "TKIP") )
+ c->pair_ciphers |= IWINFO_CIPHER_TKIP;
+
+ if( strstr(val, "CCMP") )
+ c->pair_ciphers |= IWINFO_CIPHER_CCMP;
+
+ if( strstr(val, "NONE") )
+ c->pair_ciphers |= IWINFO_CIPHER_NONE;
+ }
+
+ if( (val = nl80211_getval(ifname, res, "auth_algs")) != NULL )
+ {
switch(atoi(val)) {
case 1:
c->auth_algs |= IWINFO_AUTH_OPEN;
c->pair_ciphers |= IWINFO_CIPHER_WEP104;
}
}
-
- c->group_ciphers = c->pair_ciphers;
-
- return 0;
}
-
- if( (val = nl80211_getval(ifname, res, "wpa")) != NULL )
- c->wpa_version = atoi(val);
-
-
- val = nl80211_getval(ifname, res, "wpa_key_mgmt");
-
- if( !val || strstr(val, "PSK") )
- c->auth_suites |= IWINFO_KMGMT_PSK;
-
- if( val && strstr(val, "EAP") )
- c->auth_suites |= IWINFO_KMGMT_8021x;
-
- if( val && strstr(val, "NONE") )
- c->auth_suites |= IWINFO_KMGMT_NONE;
-
-
- if( (val = nl80211_getval(ifname, res, "wpa_pairwise")) != NULL )
- {
- if( strstr(val, "TKIP") )
- c->pair_ciphers |= IWINFO_CIPHER_TKIP;
-
- if( strstr(val, "CCMP") )
- c->pair_ciphers |= IWINFO_CIPHER_CCMP;
-
- if( strstr(val, "NONE") )
- c->pair_ciphers |= IWINFO_CIPHER_NONE;
- }
-
-
c->group_ciphers = c->pair_ciphers;
c->enabled = (c->auth_algs || c->auth_suites) ? 1 : 0;