#if defined(CONFIG_WATCHDOG)
+#define WATCHDOG_MASK (TCR_WP(63) | TCR_WRC(3) | TCR_WIE)
+void
+init_85xx_watchdog(void)
+{
+ mtspr(SPRN_TCR, (mfspr(SPRN_TCR) & ~WATCHDOG_MASK) |
+ TCR_WP(CONFIG_WATCHDOG_PRESC) | TCR_WRC(CONFIG_WATCHDOG_RC));
+}
+
void
reset_85xx_watchdog(void)
{
*decrementer_count = get_tbclk() / CONFIG_SYS_HZ;
/* PIE is same as DIE, dec interrupt enable */
- mtspr(SPRN_TCR, TCR_PIE);
+ mtspr(SPRN_TCR, mfspr(SPRN_TCR) | TCR_PIE);
#ifdef CONFIG_INTERRUPTS
pic->iivpr1 = 0x810001; /* 50220 enable ecm interrupts */
#else
#define SPRN_TCR 0x154 /* Book E Timer Control Register */
#endif /* CONFIG_BOOKE */
+#ifdef CONFIG_E500MC
+#define TCR_WP(x) (((64-x)&0x3)<<30)| \
+ (((64-x)&0x3c)<<15) /* WDT Period 2^x clocks*/
+#else
#define TCR_WP(x) (((x)&0x3)<<30) /* WDT Period */
#define WP_2_17 0 /* 2^17 clocks */
#define WP_2_21 1 /* 2^21 clocks */
#define WP_2_25 2 /* 2^25 clocks */
#define WP_2_29 3 /* 2^29 clocks */
+#endif /* CONFIG_E500 */
#define TCR_WRC(x) (((x)&0x3)<<28) /* WDT Reset Control */
#define WRC_NONE 0 /* No reset will occur */
#define WRC_CORE 1 /* Core reset will occur */
#if defined(CONFIG_WATCHDOG)
int init_func_watchdog_init(void)
{
+#if defined(CONFIG_MPC85xx)
+ init_85xx_watchdog();
+#endif
puts(" Watchdog enabled\n");
WATCHDOG_RESET();
return 0;
#define ZL30158_RST 8
#define BFTIC4_RST 0
+#define RSTRQSR1_WDT_RR 0x00200000
+#define RSTRQSR1_SW_RR 0x00100000
int board_early_init_f(void)
{
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ bool cpuwd_flag = false;
+
+ /* configure mode for uP reset request */
+ qrio_uprstreq(UPREQ_CORE_RST);
/* board only uses the DDR_MCK0, so disable the DDR_MCK1/2/3 */
setbits_be32(&gur->ddrclkdr, 0x001f000f);
+ /* set reset reason according CPU register */
+ if ((gur->rstrqsr1 & (RSTRQSR1_WDT_RR | RSTRQSR1_SW_RR)) ==
+ RSTRQSR1_WDT_RR)
+ cpuwd_flag = true;
+
+ qrio_cpuwd_flag(cpuwd_flag);
+ /* clear CPU bits by writing 1 */
+ setbits_be32(&gur->rstrqsr1, RSTRQSR1_WDT_RR | RSTRQSR1_SW_RR);
+
/* set the BFTIC's prstcfg to reset at power-up and unit reset only */
qrio_prstcfg(BFTIC4_RST, PRSTCFG_POWUP_UNIT_RST);
/* and enable WD on it */
void qrio_prstcfg(u8 bit, u8 mode);
void qrio_set_leds(void);
void qrio_enable_app_buffer(void);
+void qrio_cpuwd_flag(bool flag);
+int qrio_reset_reason(void);
+
+#define UPREQ_UNIT_RST 0x0
+#define UPREQ_CORE_RST 0x1
+
+void qrio_uprstreq(u8 mode);
void pci_of_setup(void *blob, bd_t *bd);
ctrll |= (CTRLL_WRB_BUFENA);
out_8(qrio_base + CTRLL_OFF, ctrll);
}
+
+#define REASON1_OFF 0x12
+#define REASON1_CPUWD 0x01
+
+void qrio_cpuwd_flag(bool flag)
+{
+ u8 reason1;
+ void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+ reason1 = in_8(qrio_base + REASON1_OFF);
+ if (flag)
+ reason1 |= REASON1_CPUWD;
+ else
+ reason1 &= ~REASON1_CPUWD;
+ out_8(qrio_base + REASON1_OFF, reason1);
+}
+
+#define RSTCFG_OFF 0x11
+
+void qrio_uprstreq(u8 mode)
+{
+ u32 rstcfg;
+ void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+ rstcfg = in_8(qrio_base + RSTCFG_OFF);
+
+ if (mode & UPREQ_CORE_RST)
+ rstcfg |= UPREQ_CORE_RST;
+ else
+ rstcfg &= ~UPREQ_CORE_RST;
+
+ out_8(qrio_base + RSTCFG_OFF, rstcfg);
+}
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+/*
+ * Hardware Watchdog
+ */
+#define CONFIG_WATCHDOG /* enable CPU watchdog */
+#define CONFIG_WATCHDOG_PRESC 34 /* wdog prescaler 2^(64-34) (~10min) */
+#define CONFIG_WATCHDOG_RC WRC_CHIP /* reset chip on watchdog event */
+
+
/*
* additionnal command line configuration.
*/
#if defined(CONFIG_HW_WATCHDOG) && !defined(__ASSEMBLY__)
void hw_watchdog_init(void);
#endif
+
+#if defined(CONFIG_MPC85xx) && !defined(__ASSEMBLY__)
+ void init_85xx_watchdog(void);
+#endif
#endif /* _WATCHDOG_H_ */