#define PPC_128MB_SACR_VALUE(addr) PPC_REG_VAL(PPC_128MB_SACR_BIT(addr),1)
#ifndef CONFIG_IOP480
-#define CONFIG_SYS_DCACHE_SIZE (16 << 10) /* For AMCC 405 CPUs */
+#define CONFIG_SYS_DCACHE_SIZE (16 << 10) /* For AMCC 405 CPUs */
#else
-#define CONFIG_SYS_DCACHE_SIZE (2 << 10) /* For PLX IOP480 (403) */
+#define CONFIG_SYS_DCACHE_SIZE (2 << 10) /* For PLX IOP480(403)*/
#endif
/******************************************************************************
* Decompression Controller
******************************************************************************/
#define DECOMP_DCR_BASE 0x14
-#define KIAR (DECOMP_DCR_BASE+0x0) /* Decompression controller addr reg */
-#define KIDR (DECOMP_DCR_BASE+0x1) /* Decompression controller data reg */
+#define KIAR (DECOMP_DCR_BASE+0x0) /* Decompression controller addr reg */
+#define KIDR (DECOMP_DCR_BASE+0x1) /* Decompression controller data reg */
/* values for kiar register - indirect addressing of these regs */
-#define KCONF 0x40 /* decompression core config register */
+#define KCONF 0x40 /* decompression core config register */
#endif
/******************************************************************************
#else
#define POWERMAN_DCR_BASE 0xb8
#endif
-#define CPMSR (POWERMAN_DCR_BASE+0x0) /* Power management status */
-#define CPMER (POWERMAN_DCR_BASE+0x1) /* Power management enable */
-#define CPMFR (POWERMAN_DCR_BASE+0x2) /* Power management force */
+#define CPMSR (POWERMAN_DCR_BASE+0x0) /* Power management status */
+#define CPMER (POWERMAN_DCR_BASE+0x1) /* Power management enable */
+#define CPMFR (POWERMAN_DCR_BASE+0x2) /* Power management force */
/******************************************************************************
* Extrnal Bus Controller
******************************************************************************/
/* values for EBC0_CFGADDR register - indirect addressing of these regs */
- #define PB0CR 0x00 /* periph bank 0 config reg */
- #define PB1CR 0x01 /* periph bank 1 config reg */
- #define PB2CR 0x02 /* periph bank 2 config reg */
- #define PB3CR 0x03 /* periph bank 3 config reg */
- #define PB4CR 0x04 /* periph bank 4 config reg */
+ #define PB0CR 0x00 /* periph bank 0 config reg */
+ #define PB1CR 0x01 /* periph bank 1 config reg */
+ #define PB2CR 0x02 /* periph bank 2 config reg */
+ #define PB3CR 0x03 /* periph bank 3 config reg */
+ #define PB4CR 0x04 /* periph bank 4 config reg */
#ifndef CONFIG_405EP
- #define PB5CR 0x05 /* periph bank 5 config reg */
- #define PB6CR 0x06 /* periph bank 6 config reg */
- #define PB7CR 0x07 /* periph bank 7 config reg */
+ #define PB5CR 0x05 /* periph bank 5 config reg */
+ #define PB6CR 0x06 /* periph bank 6 config reg */
+ #define PB7CR 0x07 /* periph bank 7 config reg */
#endif
- #define PB0AP 0x10 /* periph bank 0 access parameters */
- #define PB1AP 0x11 /* periph bank 1 access parameters */
- #define PB2AP 0x12 /* periph bank 2 access parameters */
- #define PB3AP 0x13 /* periph bank 3 access parameters */
- #define PB4AP 0x14 /* periph bank 4 access parameters */
+ #define PB0AP 0x10 /* periph bank 0 access parameters */
+ #define PB1AP 0x11 /* periph bank 1 access parameters */
+ #define PB2AP 0x12 /* periph bank 2 access parameters */
+ #define PB3AP 0x13 /* periph bank 3 access parameters */
+ #define PB4AP 0x14 /* periph bank 4 access parameters */
#ifndef CONFIG_405EP
- #define PB5AP 0x15 /* periph bank 5 access parameters */
- #define PB6AP 0x16 /* periph bank 6 access parameters */
- #define PB7AP 0x17 /* periph bank 7 access parameters */
+ #define PB5AP 0x15 /* periph bank 5 access parameters */
+ #define PB6AP 0x16 /* periph bank 6 access parameters */
+ #define PB7AP 0x17 /* periph bank 7 access parameters */
#endif
- #define PBEAR 0x20 /* periph bus error addr reg */
- #define PBESR0 0x21 /* periph bus error status reg 0 */
- #define PBESR1 0x22 /* periph bus error status reg 1 */
-#define EBC0_CFG 0x23 /* external bus configuration reg */
+ #define PBEAR 0x20 /* periph bus error addr reg */
+ #define PBESR0 0x21 /* periph bus error status reg 0 */
+ #define PBESR1 0x22 /* periph bus error status reg 1 */
+#define EBC0_CFG 0x23 /* external bus configuration reg */
#ifdef CONFIG_405EP
/******************************************************************************
* Control
******************************************************************************/
#define CNTRL_DCR_BASE 0x0f0
-#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode register 0 */
-#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Clock status register */
-#define CPC0_EPCTL (CNTRL_DCR_BASE+0x3) /* EMAC to PHY control register */
-#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode register 1 */
-#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART control register */
-#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI control register */
-
-#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode 0 register */
-#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Chip Clock Status register */
-#define CPC0_CR1 (CNTRL_DCR_BASE+0x2) /* Chip Control 1 register */
-#define CPC0_EPRCSR (CNTRL_DCR_BASE+0x3) /* EMAC PHY Rcv Clk Src register*/
-#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode 1 register */
-#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART Control register */
-#define CPC0_SRR (CNTRL_DCR_BASE+0x6) /* Soft Reset register */
-#define CPC0_JTAGID (CNTRL_DCR_BASE+0x7) /* JTAG ID register */
-#define CPC0_SPARE (CNTRL_DCR_BASE+0x8) /* Spare DCR */
-#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI Control register */
+#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode register 0 */
+#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Clock status register */
+#define CPC0_EPCTL (CNTRL_DCR_BASE+0x3) /* EMAC to PHY control register */
+#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode register 1 */
+#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART control register */
+#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI control register */
+
+#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode 0 register */
+#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Chip Clock Status register */
+#define CPC0_CR1 (CNTRL_DCR_BASE+0x2) /* Chip Control 1 register */
+#define CPC0_EPRCSR (CNTRL_DCR_BASE+0x3) /* EMAC PHY Rcv Clk Src register */
+#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode 1 register */
+#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART Control register */
+#define CPC0_SRR (CNTRL_DCR_BASE+0x6) /* Soft Reset register */
+#define CPC0_JTAGID (CNTRL_DCR_BASE+0x7) /* JTAG ID register */
+#define CPC0_SPARE (CNTRL_DCR_BASE+0x8) /* Spare DCR */
+#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI Control register */
/* Bit definitions */
#define PLLMR0_CPU_DIV_MASK 0x00300000 /* CPU clock divider */
#define PLLMR0_OPB_PLB_DIV_3 0x00002000
#define PLLMR0_OPB_PLB_DIV_4 0x00003000
-#define PLLMR0_EXB_TO_PLB_MASK 0x00000300 /* External Bus:PLB Divisor */
+#define PLLMR0_EXB_TO_PLB_MASK 0x00000300 /* External Bus:PLB Divisor */
#define PLLMR0_EXB_PLB_DIV_2 0x00000000
#define PLLMR0_EXB_PLB_DIV_3 0x00000100
#define PLLMR0_EXB_PLB_DIV_4 0x00000200
#define PLLMR0_EXB_PLB_DIV_5 0x00000300
-#define PLLMR0_MAL_TO_PLB_MASK 0x00000030 /* MAL:PLB Divisor */
+#define PLLMR0_MAL_TO_PLB_MASK 0x00000030 /* MAL:PLB Divisor */
#define PLLMR0_MAL_PLB_DIV_1 0x00000000
#define PLLMR0_MAL_PLB_DIV_2 0x00000010
#define PLLMR0_MAL_PLB_DIV_3 0x00000020
#define PLLMR1_SSCS_MASK 0x80000000 /* Select system clock source */
#define PLLMR1_PLLR_MASK 0x40000000 /* PLL reset */
-#define PLLMR1_FBMUL_MASK 0x00F00000 /* PLL feedback multiplier value */
+#define PLLMR1_FBMUL_MASK 0x00F00000 /* PLL feedback multiplier value */
#define PLLMR1_FBMUL_DIV_16 0x00000000
#define PLLMR1_FBMUL_DIV_1 0x00100000
#define PLLMR1_FBMUL_DIV_2 0x00200000
#define PLLMR1_FBMUL_DIV_14 0x00E00000
#define PLLMR1_FBMUL_DIV_15 0x00F00000
-#define PLLMR1_FWDVA_MASK 0x00070000 /* PLL forward divider A value */
+#define PLLMR1_FWDVA_MASK 0x00070000 /* PLL forward divider A value */
#define PLLMR1_FWDVA_DIV_8 0x00000000
#define PLLMR1_FWDVA_DIV_7 0x00010000
#define PLLMR1_FWDVA_DIV_6 0x00020000
#define PLLMR1_FWDVA_DIV_3 0x00050000
#define PLLMR1_FWDVA_DIV_2 0x00060000
#define PLLMR1_FWDVA_DIV_1 0x00070000
-#define PLLMR1_FWDVB_MASK 0x00007000 /* PLL forward divider B value */
-#define PLLMR1_TUNING_MASK 0x000003FF /* PLL tune bits */
+#define PLLMR1_FWDVB_MASK 0x00007000 /* PLL forward divider B value */
+#define PLLMR1_TUNING_MASK 0x000003FF /* PLL tune bits */
/* Defines for CPC0_EPRCSR register */
-#define CPC0_EPRCSR_E0NFE 0x80000000
-#define CPC0_EPRCSR_E1NFE 0x40000000
-#define CPC0_EPRCSR_E1RPP 0x00000080
-#define CPC0_EPRCSR_E0RPP 0x00000040
-#define CPC0_EPRCSR_E1ERP 0x00000020
-#define CPC0_EPRCSR_E0ERP 0x00000010
-#define CPC0_EPRCSR_E1PCI 0x00000002
-#define CPC0_EPRCSR_E0PCI 0x00000001
+#define CPC0_EPRCSR_E0NFE 0x80000000
+#define CPC0_EPRCSR_E1NFE 0x40000000
+#define CPC0_EPRCSR_E1RPP 0x00000080
+#define CPC0_EPRCSR_E0RPP 0x00000040
+#define CPC0_EPRCSR_E1ERP 0x00000020
+#define CPC0_EPRCSR_E0ERP 0x00000010
+#define CPC0_EPRCSR_E1PCI 0x00000002
+#define CPC0_EPRCSR_E0PCI 0x00000001
/* Defines for CPC0_PCI Register */
-#define CPC0_PCI_SPE 0x00000010 /* PCIINT/WE select */
-#define CPC0_PCI_HOST_CFG_EN 0x00000008 /* PCI host config Enable */
-#define CPC0_PCI_ARBIT_EN 0x00000001 /* PCI Internal Arb Enabled*/
+#define CPC0_PCI_SPE 0x00000010 /* PCIINT/WE select */
+#define CPC0_PCI_HOST_CFG_EN 0x00000008 /* PCI host config Enable */
+#define CPC0_PCI_ARBIT_EN 0x00000001 /* PCI Internal Arb Enabled */
/* Defines for CPC0_BOOR Register */
-#define CPC0_BOOT_SEP 0x00000002 /* serial EEPROM present */
+#define CPC0_BOOT_SEP 0x00000002 /* serial EEPROM present */
/* Defines for CPC0_PLLMR1 Register fields */
-#define PLL_ACTIVE 0x80000000
-#define CPC0_PLLMR1_SSCS 0x80000000
-#define PLL_RESET 0x40000000
-#define CPC0_PLLMR1_PLLR 0x40000000
- /* Feedback multiplier */
-#define PLL_FBKDIV 0x00F00000
-#define CPC0_PLLMR1_FBDV 0x00F00000
-#define PLL_FBKDIV_16 0x00000000
-#define PLL_FBKDIV_1 0x00100000
-#define PLL_FBKDIV_2 0x00200000
-#define PLL_FBKDIV_3 0x00300000
-#define PLL_FBKDIV_4 0x00400000
-#define PLL_FBKDIV_5 0x00500000
-#define PLL_FBKDIV_6 0x00600000
-#define PLL_FBKDIV_7 0x00700000
-#define PLL_FBKDIV_8 0x00800000
-#define PLL_FBKDIV_9 0x00900000
-#define PLL_FBKDIV_10 0x00A00000
-#define PLL_FBKDIV_11 0x00B00000
-#define PLL_FBKDIV_12 0x00C00000
-#define PLL_FBKDIV_13 0x00D00000
-#define PLL_FBKDIV_14 0x00E00000
-#define PLL_FBKDIV_15 0x00F00000
- /* Forward A divisor */
-#define PLL_FWDDIVA 0x00070000
-#define CPC0_PLLMR1_FWDVA 0x00070000
-#define PLL_FWDDIVA_8 0x00000000
-#define PLL_FWDDIVA_7 0x00010000
-#define PLL_FWDDIVA_6 0x00020000
-#define PLL_FWDDIVA_5 0x00030000
-#define PLL_FWDDIVA_4 0x00040000
-#define PLL_FWDDIVA_3 0x00050000
-#define PLL_FWDDIVA_2 0x00060000
-#define PLL_FWDDIVA_1 0x00070000
- /* Forward B divisor */
-#define PLL_FWDDIVB 0x00007000
-#define CPC0_PLLMR1_FWDVB 0x00007000
-#define PLL_FWDDIVB_8 0x00000000
-#define PLL_FWDDIVB_7 0x00001000
-#define PLL_FWDDIVB_6 0x00002000
-#define PLL_FWDDIVB_5 0x00003000
-#define PLL_FWDDIVB_4 0x00004000
-#define PLL_FWDDIVB_3 0x00005000
-#define PLL_FWDDIVB_2 0x00006000
-#define PLL_FWDDIVB_1 0x00007000
- /* PLL tune bits */
+#define PLL_ACTIVE 0x80000000
+#define CPC0_PLLMR1_SSCS 0x80000000
+#define PLL_RESET 0x40000000
+#define CPC0_PLLMR1_PLLR 0x40000000
+ /* Feedback multiplier */
+#define PLL_FBKDIV 0x00F00000
+#define CPC0_PLLMR1_FBDV 0x00F00000
+#define PLL_FBKDIV_16 0x00000000
+#define PLL_FBKDIV_1 0x00100000
+#define PLL_FBKDIV_2 0x00200000
+#define PLL_FBKDIV_3 0x00300000
+#define PLL_FBKDIV_4 0x00400000
+#define PLL_FBKDIV_5 0x00500000
+#define PLL_FBKDIV_6 0x00600000
+#define PLL_FBKDIV_7 0x00700000
+#define PLL_FBKDIV_8 0x00800000
+#define PLL_FBKDIV_9 0x00900000
+#define PLL_FBKDIV_10 0x00A00000
+#define PLL_FBKDIV_11 0x00B00000
+#define PLL_FBKDIV_12 0x00C00000
+#define PLL_FBKDIV_13 0x00D00000
+#define PLL_FBKDIV_14 0x00E00000
+#define PLL_FBKDIV_15 0x00F00000
+ /* Forward A divisor */
+#define PLL_FWDDIVA 0x00070000
+#define CPC0_PLLMR1_FWDVA 0x00070000
+#define PLL_FWDDIVA_8 0x00000000
+#define PLL_FWDDIVA_7 0x00010000
+#define PLL_FWDDIVA_6 0x00020000
+#define PLL_FWDDIVA_5 0x00030000
+#define PLL_FWDDIVA_4 0x00040000
+#define PLL_FWDDIVA_3 0x00050000
+#define PLL_FWDDIVA_2 0x00060000
+#define PLL_FWDDIVA_1 0x00070000
+ /* Forward B divisor */
+#define PLL_FWDDIVB 0x00007000
+#define CPC0_PLLMR1_FWDVB 0x00007000
+#define PLL_FWDDIVB_8 0x00000000
+#define PLL_FWDDIVB_7 0x00001000
+#define PLL_FWDDIVB_6 0x00002000
+#define PLL_FWDDIVB_5 0x00003000
+#define PLL_FWDDIVB_4 0x00004000
+#define PLL_FWDDIVB_3 0x00005000
+#define PLL_FWDDIVB_2 0x00006000
+#define PLL_FWDDIVB_1 0x00007000
+ /* PLL tune bits */
#define PLL_TUNE_MASK 0x000003FF
-#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */
-#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */
-#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */
-#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */
-#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */
-#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */
-#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */
+#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */
+#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */
+#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */
+#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */
+#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */
+#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */
+#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */
/* Defines for CPC0_PLLMR0 Register fields */
- /* CPU divisor */
-#define PLL_CPUDIV 0x00300000
-#define CPC0_PLLMR0_CCDV 0x00300000
-#define PLL_CPUDIV_1 0x00000000
-#define PLL_CPUDIV_2 0x00100000
-#define PLL_CPUDIV_3 0x00200000
-#define PLL_CPUDIV_4 0x00300000
- /* PLB divisor */
-#define PLL_PLBDIV 0x00030000
-#define CPC0_PLLMR0_CBDV 0x00030000
-#define PLL_PLBDIV_1 0x00000000
-#define PLL_PLBDIV_2 0x00010000
-#define PLL_PLBDIV_3 0x00020000
-#define PLL_PLBDIV_4 0x00030000
- /* OPB divisor */
-#define PLL_OPBDIV 0x00003000
-#define CPC0_PLLMR0_OPDV 0x00003000
-#define PLL_OPBDIV_1 0x00000000
-#define PLL_OPBDIV_2 0x00001000
-#define PLL_OPBDIV_3 0x00002000
-#define PLL_OPBDIV_4 0x00003000
- /* EBC divisor */
-#define PLL_EXTBUSDIV 0x00000300
-#define CPC0_PLLMR0_EPDV 0x00000300
-#define PLL_EXTBUSDIV_2 0x00000000
-#define PLL_EXTBUSDIV_3 0x00000100
-#define PLL_EXTBUSDIV_4 0x00000200
-#define PLL_EXTBUSDIV_5 0x00000300
- /* MAL divisor */
-#define PLL_MALDIV 0x00000030
-#define CPC0_PLLMR0_MPDV 0x00000030
-#define PLL_MALDIV_1 0x00000000
-#define PLL_MALDIV_2 0x00000010
-#define PLL_MALDIV_3 0x00000020
-#define PLL_MALDIV_4 0x00000030
- /* PCI divisor */
-#define PLL_PCIDIV 0x00000003
-#define CPC0_PLLMR0_PPFD 0x00000003
-#define PLL_PCIDIV_1 0x00000000
-#define PLL_PCIDIV_2 0x00000001
-#define PLL_PCIDIV_3 0x00000002
-#define PLL_PCIDIV_4 0x00000003
+ /* CPU divisor */
+#define PLL_CPUDIV 0x00300000
+#define CPC0_PLLMR0_CCDV 0x00300000
+#define PLL_CPUDIV_1 0x00000000
+#define PLL_CPUDIV_2 0x00100000
+#define PLL_CPUDIV_3 0x00200000
+#define PLL_CPUDIV_4 0x00300000
+ /* PLB divisor */
+#define PLL_PLBDIV 0x00030000
+#define CPC0_PLLMR0_CBDV 0x00030000
+#define PLL_PLBDIV_1 0x00000000
+#define PLL_PLBDIV_2 0x00010000
+#define PLL_PLBDIV_3 0x00020000
+#define PLL_PLBDIV_4 0x00030000
+ /* OPB divisor */
+#define PLL_OPBDIV 0x00003000
+#define CPC0_PLLMR0_OPDV 0x00003000
+#define PLL_OPBDIV_1 0x00000000
+#define PLL_OPBDIV_2 0x00001000
+#define PLL_OPBDIV_3 0x00002000
+#define PLL_OPBDIV_4 0x00003000
+ /* EBC divisor */
+#define PLL_EXTBUSDIV 0x00000300
+#define CPC0_PLLMR0_EPDV 0x00000300
+#define PLL_EXTBUSDIV_2 0x00000000
+#define PLL_EXTBUSDIV_3 0x00000100
+#define PLL_EXTBUSDIV_4 0x00000200
+#define PLL_EXTBUSDIV_5 0x00000300
+ /* MAL divisor */
+#define PLL_MALDIV 0x00000030
+#define CPC0_PLLMR0_MPDV 0x00000030
+#define PLL_MALDIV_1 0x00000000
+#define PLL_MALDIV_2 0x00000010
+#define PLL_MALDIV_3 0x00000020
+#define PLL_MALDIV_4 0x00000030
+ /* PCI divisor */
+#define PLL_PCIDIV 0x00000003
+#define CPC0_PLLMR0_PPFD 0x00000003
+#define PLL_PCIDIV_1 0x00000000
+#define PLL_PCIDIV_2 0x00000001
+#define PLL_PCIDIV_3 0x00000002
+#define PLL_PCIDIV_4 0x00000003
/*
- *-------------------------------------------------------------------------------
+ *------------------------------------------------------------------------------
* PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI,
* assuming a 33.3MHz input clock to the 405EP.
- *-------------------------------------------------------------------------------
+ *------------------------------------------------------------------------------
*/
#define PLLMR0_266_133_66 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 | \
#define CPC0_PERD1 0x0e1 /* CPR_PERD1 */
#define CPC0_PERC0 0x180 /* CPR_PERC0 */
-#define CPR_CLKUPD_ENPLLCH_EN 0x40000000 /* Enable CPR PLL Changes */
-#define CPR_CLKUPD_ENDVCH_EN 0x20000000 /* Enable CPR Sys. Div. Changes */
-#define CPR_PERD0_SPIDV_MASK 0x000F0000 /* SPI Clock Divider */
+#define CPR_CLKUPD_ENPLLCH_EN 0x40000000 /* Enable CPR PLL Changes */
+#define CPR_CLKUPD_ENDVCH_EN 0x20000000 /* Enable CPR Sys. Div. Changes */
+#define CPR_PERD0_SPIDV_MASK 0x000F0000 /* SPI Clock Divider */
-#define PLLC_SRC_MASK 0x20000000 /* PLL feedback source */
+#define PLLC_SRC_MASK 0x20000000 /* PLL feedback source */
-#define PLLD_FBDV_MASK 0x1F000000 /* PLL feedback divider value */
-#define PLLD_FWDVA_MASK 0x000F0000 /* PLL forward divider A value */
-#define PLLD_FWDVB_MASK 0x00000700 /* PLL forward divider B value */
+#define PLLD_FBDV_MASK 0x1F000000 /* PLL feedback divider value */
+#define PLLD_FWDVA_MASK 0x000F0000 /* PLL forward divider A value */
+#define PLLD_FWDVB_MASK 0x00000700 /* PLL forward divider B value */
-#define PRIMAD_CPUDV_MASK 0x0F000000 /* CPU Clock Divisor Mask */
-#define PRIMAD_PLBDV_MASK 0x000F0000 /* PLB Clock Divisor Mask */
-#define PRIMAD_OPBDV_MASK 0x00000F00 /* OPB Clock Divisor Mask */
-#define PRIMAD_EBCDV_MASK 0x0000000F /* EBC Clock Divisor Mask */
+#define PRIMAD_CPUDV_MASK 0x0F000000 /* CPU Clock Divisor Mask */
+#define PRIMAD_PLBDV_MASK 0x000F0000 /* PLB Clock Divisor Mask */
+#define PRIMAD_OPBDV_MASK 0x00000F00 /* OPB Clock Divisor Mask */
+#define PRIMAD_EBCDV_MASK 0x0000000F /* EBC Clock Divisor Mask */
-#define PERD0_PWMDV_MASK 0xFF000000 /* PWM Divider Mask */
-#define PERD0_SPIDV_MASK 0x000F0000 /* SPI Divider Mask */
-#define PERD0_U0DV_MASK 0x0000FF00 /* UART 0 Divider Mask */
-#define PERD0_U1DV_MASK 0x000000FF /* UART 1 Divider Mask */
+#define PERD0_PWMDV_MASK 0xFF000000 /* PWM Divider Mask */
+#define PERD0_SPIDV_MASK 0x000F0000 /* SPI Divider Mask */
+#define PERD0_U0DV_MASK 0x0000FF00 /* UART 0 Divider Mask */
+#define PERD0_U1DV_MASK 0x000000FF /* UART 1 Divider Mask */
#else /* #ifdef CONFIG_405EP */
/******************************************************************************
#define CPC0_ECR 0xaa /* edge conditioner register */
/* Bit definitions */
-#define PLLMR_FWD_DIV_MASK 0xE0000000 /* Forward Divisor */
+#define PLLMR_FWD_DIV_MASK 0xE0000000 /* Forward Divisor */
#define PLLMR_FWD_DIV_BYPASS 0xE0000000
#define PLLMR_FWD_DIV_3 0xA0000000
#define PLLMR_FWD_DIV_4 0x80000000
#define PLLMR_FWD_DIV_6 0x40000000
-#define PLLMR_FB_DIV_MASK 0x1E000000 /* Feedback Divisor */
+#define PLLMR_FB_DIV_MASK 0x1E000000 /* Feedback Divisor */
#define PLLMR_FB_DIV_1 0x02000000
#define PLLMR_FB_DIV_2 0x04000000
#define PLLMR_FB_DIV_3 0x06000000
#define PLLMR_TUNING_MASK 0x01F80000
-#define PLLMR_CPU_TO_PLB_MASK 0x00060000 /* CPU:PLB Frequency Divisor */
+#define PLLMR_CPU_TO_PLB_MASK 0x00060000 /* CPU:PLB Frequency Divisor */
#define PLLMR_CPU_PLB_DIV_1 0x00000000
#define PLLMR_CPU_PLB_DIV_2 0x00020000
#define PLLMR_CPU_PLB_DIV_3 0x00040000
#define PLLMR_CPU_PLB_DIV_4 0x00060000
-#define PLLMR_OPB_TO_PLB_MASK 0x00018000 /* OPB:PLB Frequency Divisor */
+#define PLLMR_OPB_TO_PLB_MASK 0x00018000 /* OPB:PLB Frequency Divisor */
#define PLLMR_OPB_PLB_DIV_1 0x00000000
#define PLLMR_OPB_PLB_DIV_2 0x00008000
#define PLLMR_OPB_PLB_DIV_3 0x00010000
#define PLLMR_OPB_PLB_DIV_4 0x00018000
-#define PLLMR_PCI_TO_PLB_MASK 0x00006000 /* PCI:PLB Frequency Divisor */
+#define PLLMR_PCI_TO_PLB_MASK 0x00006000 /* PCI:PLB Frequency Divisor */
#define PLLMR_PCI_PLB_DIV_1 0x00000000
#define PLLMR_PCI_PLB_DIV_2 0x00002000
#define PLLMR_PCI_PLB_DIV_3 0x00004000
#define PLLMR_PCI_PLB_DIV_4 0x00006000
-#define PLLMR_EXB_TO_PLB_MASK 0x00001800 /* External Bus:PLB Divisor */
+#define PLLMR_EXB_TO_PLB_MASK 0x00001800 /* External Bus:PLB Divisor */
#define PLLMR_EXB_PLB_DIV_2 0x00000000
#define PLLMR_EXB_PLB_DIV_3 0x00000800
#define PLLMR_EXB_PLB_DIV_4 0x00001000
#define PLLMR_EXB_PLB_DIV_5 0x00001800
/* definitions for PPC405GPr (new mode strapping) */
-#define PLLMR_FWDB_DIV_MASK 0x00000007 /* Forward Divisor B */
+#define PLLMR_FWDB_DIV_MASK 0x00000007 /* Forward Divisor B */
#define PSR_PLL_FWD_MASK 0xC0000000
#define PSR_PLL_FDBACK_MASK 0x30000000
#define PSR_ROM_WIDTH_MASK 0x00018000
#define PSR_ROM_LOC 0x00004000
#define PSR_PCI_ASYNC_EN 0x00001000
-#define PSR_PERCLK_SYNC_MODE_EN 0x00000800 /* PPC405GPr only */
+#define PSR_PERCLK_SYNC_MODE_EN 0x00000800 /* PPC405GPr only */
#define PSR_PCI_ARBIT_EN 0x00000400
-#define PSR_NEW_MODE_EN 0x00000020 /* PPC405GPr only */
+#define PSR_NEW_MODE_EN 0x00000020 /* PPC405GPr only */
#ifndef CONFIG_IOP480
/*
* PLL Voltage Controlled Oscillator (VCO) definitions
* Maximum and minimum values (in MHz) for correct PLL operation.
- */
+*/
#define VCO_MIN 400
#define VCO_MAX 800
#endif /* #ifndef CONFIG_IOP480 */
#else
#define MAL_DCR_BASE 0x180
#endif
-#define MAL0_CFG (MAL_DCR_BASE + 0x00) /* MAL Config reg */
-#define MAL0_ESR (MAL_DCR_BASE + 0x01) /* Err Status (Read/Clear)*/
-#define MAL0_IER (MAL_DCR_BASE + 0x02) /* Interrupt enable */
-#define MAL0_TXCASR (MAL_DCR_BASE + 0x04) /* TX Channel active (set)*/
-#define MAL0_TXCARR (MAL_DCR_BASE + 0x05) /* TX Channel active (reset)*/
-#define MAL0_TXEOBISR (MAL_DCR_BASE + 0x06) /* TX End of buffer int status*/
-#define MAL0_TXDEIR (MAL_DCR_BASE + 0x07) /* TX Descr. Error Int reg */
-#define MAL0_RXCASR (MAL_DCR_BASE + 0x10) /* RX Channel active (set) */
-#define MAL0_RXCARR (MAL_DCR_BASE + 0x11) /* RX Channel active (reset) */
-#define MAL0_RXEOBISR (MAL_DCR_BASE + 0x12) /* RX End of buffer int status*/
-#define MAL0_RXDEIR (MAL_DCR_BASE + 0x13) /* RX Descr. Error Int reg */
-#define MAL0_TXCTP0R (MAL_DCR_BASE + 0x20) /* TX 0 Channel table ptr */
-#define MAL0_TXCTP1R (MAL_DCR_BASE + 0x21) /* TX 1 Channel table ptr */
-#define MAL0_TXCTP2R (MAL_DCR_BASE + 0x22) /* TX 2 Channel table ptr */
-#define MAL0_TXCTP3R (MAL_DCR_BASE + 0x23) /* TX 3 Channel table ptr */
-#define MAL0_RXCTP0R (MAL_DCR_BASE + 0x40) /* RX 0 Channel table ptr */
-#define MAL0_RXCTP1R (MAL_DCR_BASE + 0x41) /* RX 1 Channel table ptr */
-#define MAL0_RXCTP2R (MAL_DCR_BASE + 0x42) /* RX 2 Channel table ptr */
-#define MAL0_RXCTP3R (MAL_DCR_BASE + 0x43) /* RX 3 Channel table ptr */
-#define MAL0_RXCTP8R (MAL_DCR_BASE + 0x48) /* RX 8 Channel table ptr */
-#define MAL0_RXCTP16R (MAL_DCR_BASE + 0x50) /* RX 16 Channel table ptr */
-#define MAL0_RXCTP24R (MAL_DCR_BASE + 0x58) /* RX 24 Channel table ptr */
-#define MAL0_RCBS0 (MAL_DCR_BASE + 0x60) /* RX 0 Channel buffer size */
-#define MAL0_RCBS1 (MAL_DCR_BASE + 0x61) /* RX 1 Channel buffer size */
-#define MAL0_RCBS2 (MAL_DCR_BASE + 0x62) /* RX 2 Channel buffer size */
-#define MAL0_RCBS3 (MAL_DCR_BASE + 0x63) /* RX 3 Channel buffer size */
-#define MAL0_RCBS8 (MAL_DCR_BASE + 0x68) /* RX 8 Channel buffer size */
-#define MAL0_RCBS16 (MAL_DCR_BASE + 0x70) /* RX 16 Channel buffer size */
-#define MAL0_RCBS24 (MAL_DCR_BASE + 0x78) /* RX 24 Channel buffer size */
+#define MAL0_CFG (MAL_DCR_BASE + 0x00) /* MAL Config reg */
+#define MAL0_ESR (MAL_DCR_BASE + 0x01) /* Err Status (Read/Clear) */
+#define MAL0_IER (MAL_DCR_BASE + 0x02) /* Interrupt enable */
+#define MAL0_TXCASR (MAL_DCR_BASE + 0x04) /* TX Channel active (set) */
+#define MAL0_TXCARR (MAL_DCR_BASE + 0x05) /* TX Channel active (reset) */
+#define MAL0_TXEOBISR (MAL_DCR_BASE + 0x06) /* TX End of buffer int status */
+#define MAL0_TXDEIR (MAL_DCR_BASE + 0x07) /* TX Descr. Error Int reg */
+#define MAL0_RXCASR (MAL_DCR_BASE + 0x10) /* RX Channel active (set) */
+#define MAL0_RXCARR (MAL_DCR_BASE + 0x11) /* RX Channel active (reset) */
+#define MAL0_RXEOBISR (MAL_DCR_BASE + 0x12) /* RX End of buffer int status */
+#define MAL0_RXDEIR (MAL_DCR_BASE + 0x13) /* RX Descr. Error Int reg */
+#define MAL0_TXCTP0R (MAL_DCR_BASE + 0x20) /* TX 0 Channel table ptr */
+#define MAL0_TXCTP1R (MAL_DCR_BASE + 0x21) /* TX 1 Channel table ptr */
+#define MAL0_TXCTP2R (MAL_DCR_BASE + 0x22) /* TX 2 Channel table ptr */
+#define MAL0_TXCTP3R (MAL_DCR_BASE + 0x23) /* TX 3 Channel table ptr */
+#define MAL0_RXCTP0R (MAL_DCR_BASE + 0x40) /* RX 0 Channel table ptr */
+#define MAL0_RXCTP1R (MAL_DCR_BASE + 0x41) /* RX 1 Channel table ptr */
+#define MAL0_RXCTP2R (MAL_DCR_BASE + 0x42) /* RX 2 Channel table ptr */
+#define MAL0_RXCTP3R (MAL_DCR_BASE + 0x43) /* RX 3 Channel table ptr */
+#define MAL0_RXCTP8R (MAL_DCR_BASE + 0x48) /* RX 8 Channel table ptr */
+#define MAL0_RXCTP16R (MAL_DCR_BASE + 0x50) /* RX 16 Channel table ptr */
+#define MAL0_RXCTP24R (MAL_DCR_BASE + 0x58) /* RX 24 Channel table ptr */
+#define MAL0_RCBS0 (MAL_DCR_BASE + 0x60) /* RX 0 Channel buffer size */
+#define MAL0_RCBS1 (MAL_DCR_BASE + 0x61) /* RX 1 Channel buffer size */
+#define MAL0_RCBS2 (MAL_DCR_BASE + 0x62) /* RX 2 Channel buffer size */
+#define MAL0_RCBS3 (MAL_DCR_BASE + 0x63) /* RX 3 Channel buffer size */
+#define MAL0_RCBS8 (MAL_DCR_BASE + 0x68) /* RX 8 Channel buffer size */
+#define MAL0_RCBS16 (MAL_DCR_BASE + 0x70) /* RX 16 Channel buffer size */
+#define MAL0_RCBS24 (MAL_DCR_BASE + 0x78) /* RX 24 Channel buffer size */
/*-----------------------------------------------------------------------------
| IIC Register Offsets
#define OCM0_DSRC2 (OCM_DCR_BASE + 0x09) /* OCM D-side Bank 2 Config */
#define OCM0_ISRC1 (OCM_DCR_BASE + 0x0A) /* OCM I-side Bank 1Config */
#define OCM0_ISRC2 (OCM_DCR_BASE + 0x0B) /* OCM I-side Bank 2 Config */
-#define OCM0_DISDPC (OCM_DCR_BASE + 0x0C) /* OCM D-/I-side Data Par Chk*/
+#define OCM0_DISDPC (OCM_DCR_BASE + 0x0C) /* OCM D-/I-side Data Par Chk */
#else
#define OCM_DCR_BASE 0x018
#define OCM0_ISCNTL (OCM_DCR_BASE+0x01) /* OCM I-side control reg */
#define SDR0_MFR 0x4300 /* SDR0_MFR reg */
/* Defines for CPC0_EPRCSR register */
-#define CPC0_EPRCSR_E0NFE 0x80000000
-#define CPC0_EPRCSR_E1NFE 0x40000000
-#define CPC0_EPRCSR_E1RPP 0x00000080
-#define CPC0_EPRCSR_E0RPP 0x00000040
-#define CPC0_EPRCSR_E1ERP 0x00000020
-#define CPC0_EPRCSR_E0ERP 0x00000010
-#define CPC0_EPRCSR_E1PCI 0x00000002
-#define CPC0_EPRCSR_E0PCI 0x00000001
+#define CPC0_EPRCSR_E0NFE 0x80000000
+#define CPC0_EPRCSR_E1NFE 0x40000000
+#define CPC0_EPRCSR_E1RPP 0x00000080
+#define CPC0_EPRCSR_E0RPP 0x00000040
+#define CPC0_EPRCSR_E1ERP 0x00000020
+#define CPC0_EPRCSR_E0ERP 0x00000010
+#define CPC0_EPRCSR_E1PCI 0x00000002
+#define CPC0_EPRCSR_E0PCI 0x00000001
#define CPR0_CLKUPD 0x020
#define CPR0_PLLC 0x040
/* CUST0 Customer Configuration Register0 */
#define SDR0_CUST0 0x4000
-#define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */
-#define SDR0_CUST0_MUX_EMAC_SEL 0x40000000 /* Emac Selection */
-#define SDR0_CUST0_MUX_NDFC_SEL 0x80000000 /* NDFC Selection */
-#define SDR0_CUST0_MUX_GPIO_SEL 0xC0000000 /* GPIO Selection */
-
-#define SDR0_CUST0_NDFC_EN_MASK 0x20000000 /* NDFC Enable Mask */
-#define SDR0_CUST0_NDFC_ENABLE 0x20000000 /* NDFC Enable */
-#define SDR0_CUST0_NDFC_DISABLE 0x00000000 /* NDFC Disable */
-
-#define SDR0_CUST0_NDFC_BW_MASK 0x10000000 /* NDFC Boot Width */
-#define SDR0_CUST0_NDFC_BW_16_BIT 0x10000000 /* NDFC Boot Width = 16 Bit */
-#define SDR0_CUST0_NDFC_BW_8_BIT 0x00000000 /* NDFC Boot Width = 8 Bit */
-
-#define SDR0_CUST0_NDFC_BP_MASK 0x0F000000 /* NDFC Boot Page */
-#define SDR0_CUST0_NDFC_BP_ENCODE(n) ((((unsigned long)(n))&0xF)<<24)
-#define SDR0_CUST0_NDFC_BP_DECODE(n) ((((unsigned long)(n))>>24)&0x0F)
-
-#define SDR0_CUST0_NDFC_BAC_MASK 0x00C00000 /* NDFC Boot Address Cycle */
-#define SDR0_CUST0_NDFC_BAC_ENCODE(n) ((((unsigned long)(n))&0x3)<<22)
-#define SDR0_CUST0_NDFC_BAC_DECODE(n) ((((unsigned long)(n))>>22)&0x03)
-
-#define SDR0_CUST0_NDFC_ARE_MASK 0x00200000 /* NDFC Auto Read Enable */
-#define SDR0_CUST0_NDFC_ARE_ENABLE 0x00200000 /* NDFC Auto Read Enable */
-#define SDR0_CUST0_NDFC_ARE_DISABLE 0x00000000 /* NDFC Auto Read Disable */
-
-#define SDR0_CUST0_NRB_MASK 0x00100000 /* NDFC Ready / Busy */
-#define SDR0_CUST0_NRB_BUSY 0x00100000 /* Busy */
-#define SDR0_CUST0_NRB_READY 0x00000000 /* Ready */
-
-#define SDR0_CUST0_NDRSC_MASK 0x0000FFF0 /* NDFC Device Reset Count Mask */
-#define SDR0_CUST0_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFF)<<4)
-#define SDR0_CUST0_NDRSC_DECODE(n) ((((unsigned long)(n))>>4)&0xFFF)
-
-#define SDR0_CUST0_CHIPSELGAT_MASK 0x0000000F /* Chip Select Gating Mask */
-#define SDR0_CUST0_CHIPSELGAT_DIS 0x00000000 /* Chip Select Gating Disable */
-#define SDR0_CUST0_CHIPSELGAT_ENALL 0x0000000F /* All Chip Select Gating Enable */
-#define SDR0_CUST0_CHIPSELGAT_EN0 0x00000008 /* Chip Select0 Gating Enable */
-#define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Select1 Gating Enable */
-#define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Select2 Gating Enable */
-#define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Select3 Gating Enable */
+#define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */
+#define SDR0_CUST0_MUX_EMAC_SEL 0x40000000 /* Emac Selection */
+#define SDR0_CUST0_MUX_NDFC_SEL 0x80000000 /* NDFC Selection */
+#define SDR0_CUST0_MUX_GPIO_SEL 0xC0000000 /* GPIO Selection */
+
+#define SDR0_CUST0_NDFC_EN_MASK 0x20000000 /* NDFC Enable Mask */
+#define SDR0_CUST0_NDFC_ENABLE 0x20000000 /* NDFC Enable */
+#define SDR0_CUST0_NDFC_DISABLE 0x00000000 /* NDFC Disable */
+
+#define SDR0_CUST0_NDFC_BW_MASK 0x10000000 /* NDFC Boot Width */
+#define SDR0_CUST0_NDFC_BW_16_BIT 0x10000000 /* NDFC Boot Width= 16 Bit */
+#define SDR0_CUST0_NDFC_BW_8_BIT 0x00000000 /* NDFC Boot Width= 8 Bit */
+
+#define SDR0_CUST0_NDFC_BP_MASK 0x0F000000 /* NDFC Boot Page */
+#define SDR0_CUST0_NDFC_BP_ENCODE(n) ((((unsigned long)(n))&0xF)<<24)
+#define SDR0_CUST0_NDFC_BP_DECODE(n) ((((unsigned long)(n))>>24)&0x0F)
+
+#define SDR0_CUST0_NDFC_BAC_MASK 0x00C00000 /* NDFC Boot Address Cycle */
+#define SDR0_CUST0_NDFC_BAC_ENCODE(n) ((((unsigned long)(n))&0x3)<<22)
+#define SDR0_CUST0_NDFC_BAC_DECODE(n) ((((unsigned long)(n))>>22)&0x03)
+
+#define SDR0_CUST0_NDFC_ARE_MASK 0x00200000 /* NDFC Auto Read Enable */
+#define SDR0_CUST0_NDFC_ARE_ENABLE 0x00200000 /* NDFC Auto Read Enable */
+#define SDR0_CUST0_NDFC_ARE_DISABLE 0x00000000 /* NDFC Auto Read Disable */
+
+#define SDR0_CUST0_NRB_MASK 0x00100000 /* NDFC Ready / Busy */
+#define SDR0_CUST0_NRB_BUSY 0x00100000 /* Busy */
+#define SDR0_CUST0_NRB_READY 0x00000000 /* Ready */
+
+#define SDR0_CUST0_NDRSC_MASK 0x0000FFF0 /* NDFC Device Reset Count Mask */
+#define SDR0_CUST0_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFF)<<4)
+#define SDR0_CUST0_NDRSC_DECODE(n) ((((unsigned long)(n))>>4)&0xFFF)
+
+#define SDR0_CUST0_CHIPSELGAT_MASK 0x0000000F /* Chip Sel Gating Mask */
+#define SDR0_CUST0_CHIPSELGAT_DIS 0x00000000 /* Chip Sel Gating Disable */
+#define SDR0_CUST0_CHIPSELGAT_ENALL 0x0000000F /* All Chip Sel Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN0 0x00000008 /* Chip Sel0 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Sel1 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Sel2 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Sel3 Gating Enable */
#define SDR0_PFC0 0x4100
#define SDR0_PFC1 0x4101
#ifndef __PPC440_H__
#define __PPC440_H__
-#define CONFIG_SYS_DCACHE_SIZE (32 << 10) /* For AMCC 440 CPUs */
+#define CONFIG_SYS_DCACHE_SIZE (32 << 10) /* For AMCC 440 CPUs */
/******************************************************************************
* DCRs & Related
#define SDR0_XPLLC 0x01c1
#define SDR0_XPLLD 0x01c2
#define SDR0_SRST 0x0200
-#define SD0_AMP0 0x0240 /* Override PLB4 prioritiy for up to 8 masters */
-#define SD0_AMP1 0x0241 /* Override PLB3 prioritiy for up to 8 masters */
+#define SD0_AMP0 0x0240 /* Override PLB4 prioritiy for up to 8 masters */
+#define SD0_AMP1 0x0241 /* Override PLB3 prioritiy for up to 8 masters */
#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
#define SDR0_PCI0 0x01c0
#else
#define SDR0_XCR2 0x01c6
#define SDR0_XPLLC0 0x01c1
#define SDR0_XPLLD0 0x01c2
-#define SDR0_XPLLC1 0x01c4 /*notRCW - SG */
-#define SDR0_XPLLD1 0x01c5 /*notRCW - SG */
-#define SDR0_XPLLC2 0x01c7 /*notRCW - SG */
-#define SDR0_XPLLD2 0x01c8 /*notRCW - SG */
+#define SDR0_XPLLC1 0x01c4 /* notRCW - SG */
+#define SDR0_XPLLD1 0x01c5 /* notRCW - SG */
+#define SDR0_XPLLC2 0x01c7 /* notRCW - SG */
+#define SDR0_XPLLD2 0x01c8 /* dnotRCW - SG */
#define SD0_AMP0 0x0240
#define SD0_AMP1 0x0241
#define SDR0_CUST2 0x4004
#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
-/* PLB3 Arbiter */
+ /* PLB3 Arbiter */
#define PLB3_DCR_BASE 0x070
#define PLB3_ACR (PLB3_DCR_BASE + 0x7)
-/* PLB4 Arbiter - PowerPC440EP Pass1 */
+ /* PLB4 Arbiter - PowerPC440EP Pass1 */
#define PLB4_DCR_BASE 0x080
#define PLB4_ACR (PLB4_DCR_BASE + 0x1)
#define PLB4_ACR_WRP (0x80000000 >> 7)
-/* Pin Function Control Register 1 */
+ /* Pin Function Control Register 1 */
#define SDR0_PFC1 0x4101
-#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */
-#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */
-#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */
-#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */
-#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */
-#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */
-#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */
-#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */
-#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */
-#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */
-#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */
-#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */
-#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req Selection */
-#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */
-#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */
-#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5) Selection */
-#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */
-#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */
-#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27) Selection */
-#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */
-#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */
-#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject Selection */
-#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject Disable */
-#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject Enable */
-
-#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor En. Selection */
-#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor Enable */
-#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor Enable */
-#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation Gated In */
-
-/* USB Control Register */
+#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */
+#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */
+#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */
+#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */
+#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */
+#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */
+#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */
+#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */
+#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */
+#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */
+#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */
+#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */
+#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold
+ Req Selection */
+#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */
+#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */
+#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5)
+ Selection */
+#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */
+#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */
+#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27)
+ Selection */
+#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En.
+ Selected */
+#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */
+#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject
+ Selection */
+#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject
+ Disable */
+#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject
+ Enable */
+
+#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor Enable
+ Selection */
+#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor
+ Enable */
+#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor
+ Enable */
+#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation
+ Gated In */
+
+ /* USB Control Register */
#define SDR0_USB0 0x0320
-#define SDR0_USB0_USB_DEVSEL_MASK 0x00000002 /* USB Device Selection */
-#define SDR0_USB0_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */
-#define SDR0_USB0_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */
-#define SDR0_USB0_LEEN_MASK 0x00000001 /* Little Endian selection */
-#define SDR0_USB0_LEEN_DISABLE 0x00000000 /* Little Endian Disable */
-#define SDR0_USB0_LEEN_ENABLE 0x00000001 /* Little Endian Enable */
-
-/* Miscealleneaous Function Reg. */
+#define SDR0_USB0_USB_DEVSEL_MASK 0x00000002 /* USB Device Selection */
+#define SDR0_USB0_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */
+#define SDR0_USB0_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */
+#define SDR0_USB0_LEEN_MASK 0x00000001 /* Little Endian selection */
+#define SDR0_USB0_LEEN_DISABLE 0x00000000 /* Little Endian Disable */
+#define SDR0_USB0_LEEN_ENABLE 0x00000001 /* Little Endian Enable */
+
+ /* Miscealleneaous Function Reg. */
#define SDR0_MFR 0x4300
-#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */
-#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000
-#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */
-#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000
-#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */
-#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */
-#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */
-#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */
-#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs */
-#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */
-#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */
-#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24)
-#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3)
-
-#define SDR0_MFR_ERRATA3_EN0 0x00800000
-#define SDR0_MFR_ERRATA3_EN1 0x00400000
-#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */
-#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Enable on both EMAC3 0-1 */
-#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */
-#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */
-#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */
+#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */
+#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000
+#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */
+#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000
+#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */
+#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */
+#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */
+#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */
+#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs */
+#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */
+#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */
+#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24)
+#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3)
+
+#define SDR0_MFR_ERRATA3_EN0 0x00800000
+#define SDR0_MFR_ERRATA3_EN1 0x00400000
+#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */
+#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Ena. on both EMAC3 0-1 */
+#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */
+#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */
+#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */
#define GPT0_COMP6 0x00000098
#define GPT0_COMP5 0x00000094
#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
#define SDR0_USB2D0CR 0x0320
-#define SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK 0x00000004 /* USB 2.0 Device/EBC Master Selection */
-#define SDR0_USB2D0CR_USB2DEV_SELECTION 0x00000004 /* USB 2.0 Device Selection */
-#define SDR0_USB2D0CR_EBC_SELECTION 0x00000000 /* EBC Selection */
-
-#define SDR0_USB2D0CR_USB_DEV_INT_SEL_MASK 0x00000002 /* USB Device Interface Selection */
-#define SDR0_USB2D0CR_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */
-#define SDR0_USB2D0CR_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */
-
-#define SDR0_USB2D0CR_LEEN_MASK 0x00000001 /* Little Endian selection */
-#define SDR0_USB2D0CR_LEEN_DISABLE 0x00000000 /* Little Endian Disable */
-#define SDR0_USB2D0CR_LEEN_ENABLE 0x00000001 /* Little Endian Enable */
-
-/* USB2 Host Control Register */
-#define SDR0_USB2H0CR 0x0340
-#define SDR0_USB2H0CR_WDINT_MASK 0x00000001 /* Host UTMI Word Interface */
-#define SDR0_USB2H0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit/60MHz */
-#define SDR0_USB2H0CR_WDINT_16BIT_30MHZ 0x00000001 /* 16-bit/30MHz */
-#define SDR0_USB2H0CR_EFLADJ_MASK 0x0000007e /* EHCI Frame Length Adjustment */
-
-/* Pin Function Control Register 1 */
-#define SDR0_PFC1 0x4101
-#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */
-#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */
-#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */
-
-#define SDR0_PFC1_SELECT_MASK 0x01C00000 /* Ethernet Pin Select EMAC 0 */
-#define SDR0_PFC1_SELECT_CONFIG_1_1 0x00C00000 /* 1xMII using RGMII bridge */
-#define SDR0_PFC1_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII bridge */
-#define SDR0_PFC1_SELECT_CONFIG_2 0x00C00000 /* 1xGMII using RGMII bridge */
-#define SDR0_PFC1_SELECT_CONFIG_3 0x01000000 /* 1xTBI using RGMII bridge */
-#define SDR0_PFC1_SELECT_CONFIG_4 0x01400000 /* 2xRGMII using RGMII bridge */
-#define SDR0_PFC1_SELECT_CONFIG_5 0x01800000 /* 2xRTBI using RGMII bridge */
-#define SDR0_PFC1_SELECT_CONFIG_6 0x00800000 /* 2xSMII using ZMII bridge */
-
-#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */
-#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */
-#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */
-#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */
-#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */
-#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */
-#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */
-#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */
-#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */
-#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req Selection */
-#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */
-#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */
-#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5) Selection */
-#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */
-#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */
-#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27) Selection */
-#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */
-#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */
-#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject Selection */
-#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject Disable */
-#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject Enable */
-
-#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor En. Selection */
-#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor Enable */
-#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor Enable */
-#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation Gated In */
-
-/* Ethernet PLL Configuration Register */
-#define SDR0_PFC2 0x4102
-#define SDR0_PFC2_TUNE_MASK 0x01FF8000 /* Loop stability tuning bits */
-#define SDR0_PFC2_MULTI_MASK 0x00007C00 /* Frequency multiplication selector */
-#define SDR0_PFC2_RANGEB_MASK 0x00000380 /* PLLOUTB/C frequency selector */
-#define SDR0_PFC2_RANGEA_MASK 0x00000071 /* PLLOUTA frequency selector */
-
-#define SDR0_PFC2_SELECT_MASK 0xE0000000 /* Ethernet Pin select EMAC1 */
-#define SDR0_PFC2_SELECT_CONFIG_1_1 0x60000000 /* 1xMII using RGMII bridge */
-#define SDR0_PFC2_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII bridge */
-#define SDR0_PFC2_SELECT_CONFIG_2 0x60000000 /* 1xGMII using RGMII bridge */
-#define SDR0_PFC2_SELECT_CONFIG_3 0x80000000 /* 1xTBI using RGMII bridge */
-#define SDR0_PFC2_SELECT_CONFIG_4 0xA0000000 /* 2xRGMII using RGMII bridge */
-#define SDR0_PFC2_SELECT_CONFIG_5 0xC0000000 /* 2xRTBI using RGMII bridge */
-#define SDR0_PFC2_SELECT_CONFIG_6 0x40000000 /* 2xSMII using ZMII bridge */
+#define SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK 0x00000004 /* USB 2.0 Device/EBC
+ Master Selection */
+#define SDR0_USB2D0CR_USB2DEV_SELECTION 0x00000004 /* USB 2.0 Device Selection*/
+#define SDR0_USB2D0CR_EBC_SELECTION 0x00000000 /* EBC Selection */
+
+#define SDR0_USB2D0CR_USB_DEV_INT_SEL_MASK 0x00000002 /* USB Device Interface
+ Selection */
+#define SDR0_USB2D0CR_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */
+#define SDR0_USB2D0CR_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */
+
+#define SDR0_USB2D0CR_LEEN_MASK 0x00000001 /* Little Endian selection */
+#define SDR0_USB2D0CR_LEEN_DISABLE 0x00000000 /* Little Endian Disable */
+#define SDR0_USB2D0CR_LEEN_ENABLE 0x00000001 /* Little Endian Enable */
+
+ /* USB2 Host Control Register */
+#define SDR0_USB2H0CR 0x0340
+#define SDR0_USB2H0CR_WDINT_MASK 0x00000001 /* Host UTMI Word Interface*/
+#define SDR0_USB2H0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit/60MHz */
+#define SDR0_USB2H0CR_WDINT_16BIT_30MHZ 0x00000001 /* 16-bit/30MHz */
+#define SDR0_USB2H0CR_EFLADJ_MASK 0x0000007e /* EHCI Frame Length
+ Adjustment */
+
+ /* Pin Function Control Register 1 */
+#define SDR0_PFC1 0x4101
+#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */
+#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */
+#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */
+
+#define SDR0_PFC1_SELECT_MASK 0x01C00000 /* Ethernet Pin Select
+ EMAC 0 */
+#define SDR0_PFC1_SELECT_CONFIG_1_1 0x00C00000 /* 1xMII using RGMII
+ bridge */
+#define SDR0_PFC1_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII
+ bridge */
+#define SDR0_PFC1_SELECT_CONFIG_2 0x00C00000 /* 1xGMII using RGMII
+ bridge */
+#define SDR0_PFC1_SELECT_CONFIG_3 0x01000000 /* 1xTBI using RGMII
+ bridge */
+#define SDR0_PFC1_SELECT_CONFIG_4 0x01400000 /* 2xRGMII using RGMII
+ bridge */
+#define SDR0_PFC1_SELECT_CONFIG_5 0x01800000 /* 2xRTBI using RGMII
+ bridge */
+#define SDR0_PFC1_SELECT_CONFIG_6 0x00800000 /* 2xSMII using ZMII
+ bridge */
+
+#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */
+#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */
+#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */
+#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */
+#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */
+#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */
+#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */
+#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */
+#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */
+#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req
+ Selection */
+#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */
+#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */
+#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5)
+ Selection */
+#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */
+#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */
+#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27)
+ Selection */
+#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */
+#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */
+#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject
+ Selection */
+#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject
+ Disable */
+#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject
+ Enable */
+
+#define SDR0_PFC1_PLB_PME_MASK 0x00001000
+ /* PLB3/PLB4 Perf. Monitor En. Selection */
+#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000
+ /* PLB3 Performance Monitor Enable */
+#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000
+ /* PLB3 Performance Monitor Enable */
+#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation
+ Gated In */
+
+ /* Ethernet PLL Configuration Register */
+#define SDR0_PFC2 0x4102
+#define SDR0_PFC2_TUNE_MASK 0x01FF8000 /* Loop stability tuning bits */
+#define SDR0_PFC2_MULTI_MASK 0x00007C00 /* Frequency multiplication
+ selector */
+#define SDR0_PFC2_RANGEB_MASK 0x00000380 /* PLLOUTB/C frequency selector */
+#define SDR0_PFC2_RANGEA_MASK 0x00000071 /* PLLOUTA frequency selector */
+
+#define SDR0_PFC2_SELECT_MASK 0xE0000000 /* Ethernet Pin select EMAC1 */
+#define SDR0_PFC2_SELECT_CONFIG_1_1 0x60000000 /* 1xMII using RGMII bridge */
+#define SDR0_PFC2_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII bridge */
+#define SDR0_PFC2_SELECT_CONFIG_2 0x60000000 /* 1xGMII using RGMII bridge */
+#define SDR0_PFC2_SELECT_CONFIG_3 0x80000000 /* 1xTBI using RGMII bridge */
+#define SDR0_PFC2_SELECT_CONFIG_4 0xA0000000 /* 2xRGMII using RGMII bridge */
+#define SDR0_PFC2_SELECT_CONFIG_5 0xC0000000 /* 2xRTBI using RGMII bridge */
+#define SDR0_PFC2_SELECT_CONFIG_6 0x40000000 /* 2xSMII using ZMII bridge */
#define SDR0_PFC4 0x4104
-/* USB2PHY0 Control Register */
-#define SDR0_USB2PHY0CR 0x4103
-#define SDR0_USB2PHY0CR_UTMICN_MASK 0x00100000 /* PHY UTMI interface connection */
-#define SDR0_USB2PHY0CR_UTMICN_DEV 0x00000000 /* Device support */
-#define SDR0_USB2PHY0CR_UTMICN_HOST 0x00100000 /* Host support */
-
-#define SDR0_USB2PHY0CR_DWNSTR_MASK 0x00400000 /* Select downstream port mode */
-#define SDR0_USB2PHY0CR_DWNSTR_DEV 0x00000000 /* Device */
-#define SDR0_USB2PHY0CR_DWNSTR_HOST 0x00400000 /* Host */
-
-#define SDR0_USB2PHY0CR_DVBUS_MASK 0x00800000 /* VBus detect (Device mode only) */
-#define SDR0_USB2PHY0CR_DVBUS_PURDIS 0x00000000 /* Pull-up resistance on D+ is disabled */
-#define SDR0_USB2PHY0CR_DVBUS_PUREN 0x00800000 /* Pull-up resistance on D+ is enabled */
-
-#define SDR0_USB2PHY0CR_WDINT_MASK 0x01000000 /* PHY UTMI data width and clock select */
-#define SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit data/60MHz */
-#define SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ 0x01000000 /* 16-bit data/30MHz */
-
-#define SDR0_USB2PHY0CR_LOOPEN_MASK 0x02000000 /* Loop back test enable */
-#define SDR0_USB2PHY0CR_LOOP_ENABLE 0x00000000 /* Loop back disabled */
-#define SDR0_USB2PHY0CR_LOOP_DISABLE 0x02000000 /* Loop back enabled (only test purposes) */
-
-#define SDR0_USB2PHY0CR_XOON_MASK 0x04000000 /* Force XO block on during a suspend */
-#define SDR0_USB2PHY0CR_XO_ON 0x00000000 /* PHY XO block is powered-on */
-#define SDR0_USB2PHY0CR_XO_OFF 0x04000000 /* PHY XO block is powered-off when all ports are suspended */
-
-#define SDR0_USB2PHY0CR_PWRSAV_MASK 0x08000000 /* Select PHY power-save mode */
-#define SDR0_USB2PHY0CR_PWRSAV_OFF 0x00000000 /* Non-power-save mode */
-#define SDR0_USB2PHY0CR_PWRSAV_ON 0x08000000 /* Power-save mode. Valid only for full-speed operation */
-
-#define SDR0_USB2PHY0CR_XOREF_MASK 0x10000000 /* Select reference clock source */
-#define SDR0_USB2PHY0CR_XOREF_INTERNAL 0x00000000 /* PHY PLL uses chip internal 48M clock as a reference */
-#define SDR0_USB2PHY0CR_XOREF_XO 0x10000000 /* PHY PLL uses internal XO block output as a reference */
-
-#define SDR0_USB2PHY0CR_XOCLK_MASK 0x20000000 /* Select clock for XO block */
-#define SDR0_USB2PHY0CR_XOCLK_EXTERNAL 0x00000000 /* PHY macro used an external clock */
-#define SDR0_USB2PHY0CR_XOCLK_CRYSTAL 0x20000000 /* PHY macro uses the clock from a crystal */
-
-#define SDR0_USB2PHY0CR_CLKSEL_MASK 0xc0000000 /* Select ref clk freq */
-#define SDR0_USB2PHY0CR_CLKSEL_12MHZ 0x00000000 /* Select ref clk freq = 12 MHz*/
-#define SDR0_USB2PHY0CR_CLKSEL_48MHZ 0x40000000 /* Select ref clk freq = 48 MHz*/
-#define SDR0_USB2PHY0CR_CLKSEL_24MHZ 0x80000000 /* Select ref clk freq = 24 MHz*/
-
-/* Miscealleneaous Function Reg. */
-#define SDR0_MFR 0x4300
-#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */
-#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000
-#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */
-#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000
-#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */
-#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */
-#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */
-#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */
-#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */
-#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24)
-#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3)
-
-#define SDR0_MFR_ERRATA3_EN0 0x00800000
-#define SDR0_MFR_ERRATA3_EN1 0x00400000
-#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */
-#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Enable on both EMAC3 0-1 */
-#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */
-#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */
-#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */
+ /* USB2PHY0 Control Register */
+#define SDR0_USB2PHY0CR 0x4103
+#define SDR0_USB2PHY0CR_UTMICN_MASK 0x00100000
+
+ /* PHY UTMI interface connection */
+#define SDR0_USB2PHY0CR_UTMICN_DEV 0x00000000 /* Device support */
+#define SDR0_USB2PHY0CR_UTMICN_HOST 0x00100000 /* Host support */
+
+#define SDR0_USB2PHY0CR_DWNSTR_MASK 0x00400000 /* Select downstream port mode */
+#define SDR0_USB2PHY0CR_DWNSTR_DEV 0x00000000 /* Device */
+#define SDR0_USB2PHY0CR_DWNSTR_HOST 0x00400000 /* Host */
+
+#define SDR0_USB2PHY0CR_DVBUS_MASK 0x00800000
+ /* VBus detect (Device mode only) */
+#define SDR0_USB2PHY0CR_DVBUS_PURDIS 0x00000000
+ /* Pull-up resistance on D+ is disabled */
+#define SDR0_USB2PHY0CR_DVBUS_PUREN 0x00800000
+ /* Pull-up resistance on D+ is enabled */
+
+#define SDR0_USB2PHY0CR_WDINT_MASK 0x01000000
+ /* PHY UTMI data width and clock select */
+#define SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit data/60MHz */
+#define SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ 0x01000000 /* 16-bit data/30MHz */
+
+#define SDR0_USB2PHY0CR_LOOPEN_MASK 0x02000000 /* Loop back test enable */
+#define SDR0_USB2PHY0CR_LOOP_ENABLE 0x00000000 /* Loop back disabled */
+#define SDR0_USB2PHY0CR_LOOP_DISABLE 0x02000000
+ /* Loop back enabled (only test purposes) */
+
+#define SDR0_USB2PHY0CR_XOON_MASK 0x04000000
+ /* Force XO block on during a suspend */
+#define SDR0_USB2PHY0CR_XO_ON 0x00000000 /* PHY XO block is powered-on */
+#define SDR0_USB2PHY0CR_XO_OFF 0x04000000
+ /* PHY XO block is powered-off when all ports are suspended */
+
+#define SDR0_USB2PHY0CR_PWRSAV_MASK 0x08000000 /* Select PHY power-save mode */
+#define SDR0_USB2PHY0CR_PWRSAV_OFF 0x00000000 /* Non-power-save mode */
+#define SDR0_USB2PHY0CR_PWRSAV_ON 0x08000000 /* Power-save mode. Valid only
+ for full-speed operation */
+
+#define SDR0_USB2PHY0CR_XOREF_MASK 0x10000000 /* Select reference clock
+ source */
+#define SDR0_USB2PHY0CR_XOREF_INTERNAL 0x00000000 /* PHY PLL uses chip internal
+ 48M clock as a reference */
+#define SDR0_USB2PHY0CR_XOREF_XO 0x10000000 /* PHY PLL uses internal XO
+ block output as a reference */
+
+#define SDR0_USB2PHY0CR_XOCLK_MASK 0x20000000 /* Select clock for XO
+ block*/
+#define SDR0_USB2PHY0CR_XOCLK_EXTERNAL 0x00000000 /* PHY macro used an external
+ clock */
+#define SDR0_USB2PHY0CR_XOCLK_CRYSTAL 0x20000000 /* PHY macro uses the clock
+ from a crystal */
+
+#define SDR0_USB2PHY0CR_CLKSEL_MASK 0xc0000000 /* Select ref clk freq */
+#define SDR0_USB2PHY0CR_CLKSEL_12MHZ 0x00000000 /* Select ref clk freq
+ = 12 MHz */
+#define SDR0_USB2PHY0CR_CLKSEL_48MHZ 0x40000000 /* Select ref clk freq
+ = 48 MHz */
+#define SDR0_USB2PHY0CR_CLKSEL_24MHZ 0x80000000 /* Select ref clk freq
+ = 24 MHz */
+
+ /* Miscealleneaous Function Reg. */
+#define SDR0_MFR 0x4300
+#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */
+#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000
+#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */
+#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000
+#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */
+#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */
+#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */
+#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */
+#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */
+#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24)
+#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3)
+
+#define SDR0_MFR_ERRATA3_EN0 0x00800000
+#define SDR0_MFR_ERRATA3_EN1 0x00400000
+#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */
+#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Ena. on both EMAC3 0-1 */
+#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */
+#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */
+#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */
#endif /* defined(CONFIG_440EPX) || defined(CONFIG_440GRX) */
-/* CUST1 Customer Configuration Register1 */
-#define SDR0_CUST1 0x4002
-#define SDR0_CUST1_NDRSC_MASK 0xFFFF0000 /* NDRSC Device Read Count */
-#define SDR0_CUST1_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<16)
-#define SDR0_CUST1_NDRSC_DECODE(n) ((((unsigned long)(n))>>16)&0xFFFF)
-
-/* Pin Function Control Register 0 */
-#define SDR0_PFC0 0x4100
-#define SDR0_PFC0_CPU_TR_EN_MASK 0x00000100 /* CPU Trace Enable Mask */
-#define SDR0_PFC0_CPU_TRACE_EN 0x00000100 /* CPU Trace Enable */
-#define SDR0_PFC0_CPU_TRACE_DIS 0x00000100 /* CPU Trace Disable */
-#define SDR0_PFC0_CTE_ENCODE(n) ((((unsigned long)(n))&0x01)<<8)
-#define SDR0_PFC0_CTE_DECODE(n) ((((unsigned long)(n))>>8)&0x01)
-
-/* Pin Function Control Register 1 */
-#define SDR0_PFC1 0x4101
-#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */
-#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */
-#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */
-#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */
-#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */
-#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */
-#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */
-#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */
-#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */
-#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */
-#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */
-#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */
-#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req Selection */
-#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */
-#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */
-#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5) Selection */
-#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */
-#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */
-#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27) Selection */
-#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */
-#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */
-#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject Selection */
-#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject Disable */
-#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject Enable */
-
-#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor En. Selection */
-#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor Enable */
-#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor Enable */
-#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation Gated In */
+ /* CUST1 Customer Configuration Register1 */
+#define SDR0_CUST1 0x4002
+#define SDR0_CUST1_NDRSC_MASK 0xFFFF0000 /* NDRSC Device Read Count */
+#define SDR0_CUST1_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<16)
+#define SDR0_CUST1_NDRSC_DECODE(n) ((((unsigned long)(n))>>16)&0xFFFF)
+
+ /* Pin Function Control Register 0 */
+#define SDR0_PFC0 0x4100
+#define SDR0_PFC0_CPU_TR_EN_MASK 0x00000100 /* CPU Trace Enable Mask */
+#define SDR0_PFC0_CPU_TRACE_EN 0x00000100 /* CPU Trace Enable */
+#define SDR0_PFC0_CPU_TRACE_DIS 0x00000100 /* CPU Trace Disable */
+#define SDR0_PFC0_CTE_ENCODE(n) ((((unsigned long)(n))&0x01)<<8)
+#define SDR0_PFC0_CTE_DECODE(n) ((((unsigned long)(n))>>8)&0x01)
+
+ /* Pin Function Control Register 1 */
+#define SDR0_PFC1 0x4101
+#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */
+#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */
+#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */
+#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */
+#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */
+#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */
+#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */
+#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */
+#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */
+#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */
+#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */
+#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */
+#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req
+ Selection */
+#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */
+#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */
+#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5)
+ Selection */
+#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */
+#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */
+#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27)
+ Selection */
+#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */
+#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */
+#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject
+ Selection */
+#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject
+ Disable */
+#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject
+ Enable */
+
+#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor En.
+ Selection */
+#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor
+ Enable */
+#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor
+ Enable */
+#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation
+ Gated In */
#endif /* 440EP || 440GR || 440EPX || 440GRX */
#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT)
-/* CUST0 Customer Configuration Register0 */
-#define SDR0_CUST0 0x4000
-#define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */
-#define SDR0_CUST0_MUX_EMAC_SEL 0x40000000 /* Emac Selection */
-#define SDR0_CUST0_MUX_NDFC_SEL 0x80000000 /* NDFC Selection */
-#define SDR0_CUST0_MUX_GPIO_SEL 0xC0000000 /* GPIO Selection */
-
-#define SDR0_CUST0_NDFC_EN_MASK 0x20000000 /* NDFC Enable Mask */
-#define SDR0_CUST0_NDFC_ENABLE 0x20000000 /* NDFC Enable */
-#define SDR0_CUST0_NDFC_DISABLE 0x00000000 /* NDFC Disable */
-
-#define SDR0_CUST0_NDFC_BW_MASK 0x10000000 /* NDFC Boot Width */
-#define SDR0_CUST0_NDFC_BW_16_BIT 0x10000000 /* NDFC Boot Width = 16 Bit */
-#define SDR0_CUST0_NDFC_BW_8_BIT 0x00000000 /* NDFC Boot Width = 8 Bit */
-
-#define SDR0_CUST0_NDFC_BP_MASK 0x0F000000 /* NDFC Boot Page */
-#define SDR0_CUST0_NDFC_BP_ENCODE(n) ((((unsigned long)(n))&0xF)<<24)
-#define SDR0_CUST0_NDFC_BP_DECODE(n) ((((unsigned long)(n))>>24)&0x0F)
-
-#define SDR0_CUST0_NDFC_BAC_MASK 0x00C00000 /* NDFC Boot Address Cycle */
-#define SDR0_CUST0_NDFC_BAC_ENCODE(n) ((((unsigned long)(n))&0x3)<<22)
-#define SDR0_CUST0_NDFC_BAC_DECODE(n) ((((unsigned long)(n))>>22)&0x03)
-
-#define SDR0_CUST0_NDFC_ARE_MASK 0x00200000 /* NDFC Auto Read Enable */
-#define SDR0_CUST0_NDFC_ARE_ENABLE 0x00200000 /* NDFC Auto Read Enable */
-#define SDR0_CUST0_NDFC_ARE_DISABLE 0x00000000 /* NDFC Auto Read Disable */
-
-#define SDR0_CUST0_NRB_MASK 0x00100000 /* NDFC Ready / Busy */
-#define SDR0_CUST0_NRB_BUSY 0x00100000 /* Busy */
-#define SDR0_CUST0_NRB_READY 0x00000000 /* Ready */
-
-#define SDR0_CUST0_NDRSC_MASK 0x0000FFF0 /* NDFC Device Reset Count Mask */
-#define SDR0_CUST0_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFF)<<4)
-#define SDR0_CUST0_NDRSC_DECODE(n) ((((unsigned long)(n))>>4)&0xFFF)
-
-#define SDR0_CUST0_CHIPSELGAT_MASK 0x0000000F /* Chip Select Gating Mask */
-#define SDR0_CUST0_CHIPSELGAT_DIS 0x00000000 /* Chip Select Gating Disable */
-#define SDR0_CUST0_CHIPSELGAT_ENALL 0x0000000F /* All Chip Select Gating Enable */
-#define SDR0_CUST0_CHIPSELGAT_EN0 0x00000008 /* Chip Select0 Gating Enable */
-#define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Select1 Gating Enable */
-#define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Select2 Gating Enable */
-#define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Select3 Gating Enable */
+ /* CUST0 Customer Configuration Register0 */
+#define SDR0_CUST0 0x4000
+#define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */
+#define SDR0_CUST0_MUX_EMAC_SEL 0x40000000 /* Emac Selection */
+#define SDR0_CUST0_MUX_NDFC_SEL 0x80000000 /* NDFC Selection */
+#define SDR0_CUST0_MUX_GPIO_SEL 0xC0000000 /* GPIO Selection */
+
+#define SDR0_CUST0_NDFC_EN_MASK 0x20000000 /* NDFC Enable Mask */
+#define SDR0_CUST0_NDFC_ENABLE 0x20000000 /* NDFC Enable */
+#define SDR0_CUST0_NDFC_DISABLE 0x00000000 /* NDFC Disable */
+
+#define SDR0_CUST0_NDFC_BW_MASK 0x10000000 /* NDFC Boot Width */
+#define SDR0_CUST0_NDFC_BW_16_BIT 0x10000000 /* NDFC Boot Width = 16 Bit */
+#define SDR0_CUST0_NDFC_BW_8_BIT 0x00000000 /* NDFC Boot Width = 8 Bit */
+
+#define SDR0_CUST0_NDFC_BP_MASK 0x0F000000 /* NDFC Boot Page */
+#define SDR0_CUST0_NDFC_BP_ENCODE(n) ((((unsigned long)(n))&0xF)<<24)
+#define SDR0_CUST0_NDFC_BP_DECODE(n) ((((unsigned long)(n))>>24)&0x0F)
+
+#define SDR0_CUST0_NDFC_BAC_MASK 0x00C00000 /* NDFC Boot Address Cycle */
+#define SDR0_CUST0_NDFC_BAC_ENCODE(n) ((((unsigned long)(n))&0x3)<<22)
+#define SDR0_CUST0_NDFC_BAC_DECODE(n) ((((unsigned long)(n))>>22)&0x03)
+
+#define SDR0_CUST0_NDFC_ARE_MASK 0x00200000 /* NDFC Auto Read Enable */
+#define SDR0_CUST0_NDFC_ARE_ENABLE 0x00200000 /* NDFC Auto Read Enable */
+#define SDR0_CUST0_NDFC_ARE_DISABLE 0x00000000 /* NDFC Auto Read Disable */
+
+#define SDR0_CUST0_NRB_MASK 0x00100000 /* NDFC Ready / Busy */
+#define SDR0_CUST0_NRB_BUSY 0x00100000 /* Busy */
+#define SDR0_CUST0_NRB_READY 0x00000000 /* Ready */
+
+#define SDR0_CUST0_NDRSC_MASK 0x0000FFF0 /* NDFC Device Reset Count Mask */
+#define SDR0_CUST0_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFF)<<4)
+#define SDR0_CUST0_NDRSC_DECODE(n) ((((unsigned long)(n))>>4)&0xFFF)
+
+#define SDR0_CUST0_CHIPSELGAT_MASK 0x0000000F /* Chip Select Gating Mask */
+#define SDR0_CUST0_CHIPSELGAT_DIS 0x00000000 /* Chip Select Gating Disable */
+#define SDR0_CUST0_CHIPSELGAT_ENALL 0x0000000F /*All Chip Select Gating Enable*/
+#define SDR0_CUST0_CHIPSELGAT_EN0 0x00000008 /* Chip Select0 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Select1 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Select2 Gating Enable */
+#define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Select3 Gating Enable */
#endif
/*-----------------------------------------------------------------------------
#define CNTRL_DCR_BASE 0x0b0
#endif
-#define CPC0_SYS0 (CNTRL_DCR_BASE+0x30) /* System configuration reg 0 */
-#define CPC0_SYS1 (CNTRL_DCR_BASE+0x31) /* System configuration reg 1 */
+#define CPC0_SYS0 (CNTRL_DCR_BASE+0x30) /* System configuration reg 0 */
+#define CPC0_SYS1 (CNTRL_DCR_BASE+0x31) /* System configuration reg 1 */
-#define CPC0_STRP0 (CNTRL_DCR_BASE+0x34) /* Power-on config reg 0 (RO) */
-#define CPC0_STRP1 (CNTRL_DCR_BASE+0x35) /* Power-on config reg 1 (RO) */
+#define CPC0_STRP0 (CNTRL_DCR_BASE+0x34) /* Power-on config reg 0 (RO) */
+#define CPC0_STRP1 (CNTRL_DCR_BASE+0x35) /* Power-on config reg 1 (RO) */
-#define CPC0_GPIO (CNTRL_DCR_BASE+0x38) /* GPIO config reg (440GP) */
+#define CPC0_GPIO (CNTRL_DCR_BASE+0x38) /* GPIO config reg (440GP) */
-#define CPC0_CR0 (CNTRL_DCR_BASE+0x3b) /* Control 0 register */
-#define CPC0_CR1 (CNTRL_DCR_BASE+0x3a) /* Control 1 register */
+#define CPC0_CR0 (CNTRL_DCR_BASE+0x3b) /* Control 0 register */
+#define CPC0_CR1 (CNTRL_DCR_BASE+0x3a) /* Control 1 register */
/*-----------------------------------------------------------------------------
| DMA
#define MAL0_IER (MAL_DCR_BASE + 0x02) /* Interrupt enable */
#define MAL0_TXCASR (MAL_DCR_BASE + 0x04) /* TX Channel active (set) */
#define MAL0_TXCARR (MAL_DCR_BASE + 0x05) /* TX Channel active (reset) */
-#define MAL0_TXEOBISR (MAL_DCR_BASE + 0x06) /* TX End of buffer int status */
+#define MAL0_TXEOBISR (MAL_DCR_BASE + 0x06) /* TX End of buffer int status*/
#define MAL0_TXDEIR (MAL_DCR_BASE + 0x07) /* TX Descr. Error Int */
#define MAL0_TXBADDR (MAL_DCR_BASE + 0x09) /* TX descriptor base addr*/
#define MAL0_RXCASR (MAL_DCR_BASE + 0x10) /* RX Channel active (set) */
#define MAL0_RXCARR (MAL_DCR_BASE + 0x11) /* RX Channel active (reset) */
-#define MAL0_RXEOBISR (MAL_DCR_BASE + 0x12) /* RX End of buffer int status */
+#define MAL0_RXEOBISR (MAL_DCR_BASE + 0x12) /* RX End of buffer int status*/
#define MAL0_RXDEIR (MAL_DCR_BASE + 0x13) /* RX Descr. Error Int */
#define MAL0_RXBADDR (MAL_DCR_BASE + 0x15) /* RX descriptor base addr */
#define MAL0_TXCTP0R (MAL_DCR_BASE + 0x20) /* TX 0 Channel table pointer */
#define SDR0_SDSTP0_TUNE_DECODE(n) ((((unsigned long)(n))>>17)&0x3FF)
#define SDR0_SDSTP0_FBDV_MASK 0x0001F000
#define SDR0_SDSTP0_FBDV_ENCODE(n) ((((unsigned long)(n))&0x1F)<<12)
-#define SDR0_SDSTP0_FBDV_DECODE(n) ((((((unsigned long)(n))>>12)-1)&0x1F)+1)
+#define SDR0_SDSTP0_FBDV_DECODE(n) ((((((unsigned long)(n))>>12)-1)&0x1F)+1)
#define SDR0_SDSTP0_FWDVA_MASK 0x00000F00
#define SDR0_SDSTP0_FWDVA_ENCODE(n) ((((unsigned long)(n))&0x0F)<<8)
#define SDR0_SDSTP0_FWDVA_DECODE(n) ((((((unsigned long)(n))>>8)-1)&0x0F)+1)
#define SDR0_SDSTP1_DBGEN_MASK 0x00000030 /* $218C */
#define SDR0_SDSTP1_DBGEN_FUNC 0x00000000
#define SDR0_SDSTP1_DBGEN_TRACE 0x00000010
-#define SDR0_SDSTP1_DBGEN_ENCODE(n) ((((unsigned long)(n))&0x03)<<4) /* $218C */
-#define SDR0_SDSTP1_DBGEN_DECODE(n) ((((unsigned long)(n))>>4)&0x03) /* $218C */
+#define SDR0_SDSTP1_DBGEN_ENCODE(n) ((((unsigned long)(n))&0x03)<<4) /* $218C */
+#define SDR0_SDSTP1_DBGEN_DECODE(n) ((((unsigned long)(n))>>4)&0x03) /* $218C */
#define SDR0_SDSTP1_ETH_MASK 0x00000004
#define SDR0_SDSTP1_ETH_10_100 0x00000000
#define SDR0_SDSTP1_ETH_GIGA 0x00000004
#define SDR0_PINSTP 0x0040
#define SDR0_PINSTP_BOOTSTRAP_MASK 0xC0000000 /* Strap Bits */
-#define SDR0_PINSTP_BOOTSTRAP_SETTINGS0 0x00000000 /* Default strap settings 0 (EBC boot) */
-#define SDR0_PINSTP_BOOTSTRAP_SETTINGS1 0x40000000 /* Default strap settings 1 (PCI boot) */
-#define SDR0_PINSTP_BOOTSTRAP_IIC_54_EN 0x80000000 /* Serial Device Enabled - Addr = 0x54 */
-#define SDR0_PINSTP_BOOTSTRAP_IIC_50_EN 0xC0000000 /* Serial Device Enabled - Addr = 0x50 */
+#define SDR0_PINSTP_BOOTSTRAP_SETTINGS0 0x00000000 /* Default strap settings 0
+ (EBC boot) */
+#define SDR0_PINSTP_BOOTSTRAP_SETTINGS1 0x40000000 /* Default strap settings 1
+ (PCI boot) */
+#define SDR0_PINSTP_BOOTSTRAP_IIC_54_EN 0x80000000 /* Serial Device Enabled -
+ Addr = 0x54 */
+#define SDR0_PINSTP_BOOTSTRAP_IIC_50_EN 0xC0000000 /* Serial Device Enabled -
+ Addr = 0x50 */
#define SDR0_SDCS 0x0060
#define SDR0_ECID0 0x0080
#define SDR0_ECID1 0x0081
#define SDR0_PFC1_CPU_TRACE_MASK 0x00180000 /* $218C */
#define SDR0_PFC1_CPU_NO_TRACE 0x00000000
#define SDR0_PFC1_CPU_TRACE 0x00080000
-#define SDR0_PFC1_CPU_TRACE_ENCODE(n) ((((unsigned long)(n))&0x3)<<19) /* $218C */
-#define SDR0_PFC1_CPU_TRACE_DECODE(n) ((((unsigned long)(n))>>19)&0x03) /* $218C */
+#define SDR0_PFC1_CPU_TRACE_ENCODE(n) ((((unsigned long)(n))&0x3)<<19)
+ /* $218C */
+#define SDR0_PFC1_CPU_TRACE_DECODE(n) ((((unsigned long)(n))>>19)&0x03)
+ /* $218C */
#define SDR0_MFR 0x4300
#endif /* CONFIG_440SPE */
/* Ethernet Configuration Register (SDR0_ETH_CFG) */
#define SDR0_ETH_CFG 0x4103
-#define SDR0_ETH_CFG_SGMII3_LPBK 0x00800000 /* SGMII3 port loopback enable */
-#define SDR0_ETH_CFG_SGMII2_LPBK 0x00400000 /* SGMII2 port loopback enable */
-#define SDR0_ETH_CFG_SGMII1_LPBK 0x00200000 /* SGMII1 port loopback enable */
-#define SDR0_ETH_CFG_SGMII0_LPBK 0x00100000 /* SGMII0 port loopback enable */
-#define SDR0_ETH_CFG_SGMII_MASK 0x00070000 /* SGMII Mask */
-#define SDR0_ETH_CFG_SGMII2_ENABLE 0x00040000 /* SGMII2 port enable */
-#define SDR0_ETH_CFG_SGMII1_ENABLE 0x00020000 /* SGMII1 port enable */
-#define SDR0_ETH_CFG_SGMII0_ENABLE 0x00010000 /* SGMII0 port enable */
-#define SDR0_ETH_CFG_TAHOE1_BYPASS 0x00002000 /* TAHOE1 Bypass selector */
-#define SDR0_ETH_CFG_TAHOE0_BYPASS 0x00001000 /* TAHOE0 Bypass selector */
-#define SDR0_ETH_CFG_EMAC3_PHY_CLK_SEL 0x00000800 /* EMAC 3 PHY clock selector */
-#define SDR0_ETH_CFG_EMAC2_PHY_CLK_SEL 0x00000400 /* EMAC 2 PHY clock selector */
-#define SDR0_ETH_CFG_EMAC1_PHY_CLK_SEL 0x00000200 /* EMAC 1 PHY clock selector */
-#define SDR0_ETH_CFG_EMAC0_PHY_CLK_SEL 0x00000100 /* EMAC 0 PHY clock selector */
-#define SDR0_ETH_CFG_EMAC_2_1_SWAP 0x00000080 /* Swap EMAC2 with EMAC1 */
-#define SDR0_ETH_CFG_EMAC_0_3_SWAP 0x00000040 /* Swap EMAC0 with EMAC3 */
-#define SDR0_ETH_CFG_MDIO_SEL_MASK 0x00000030 /* MDIO source selector mask */
-#define SDR0_ETH_CFG_MDIO_SEL_EMAC0 0x00000000 /* MDIO source - EMAC0 */
-#define SDR0_ETH_CFG_MDIO_SEL_EMAC1 0x00000010 /* MDIO source - EMAC1 */
-#define SDR0_ETH_CFG_MDIO_SEL_EMAC2 0x00000020 /* MDIO source - EMAC2 */
-#define SDR0_ETH_CFG_MDIO_SEL_EMAC3 0x00000030 /* MDIO source - EMAC3 */
-#define SDR0_ETH_CFG_ZMII_MODE_MASK 0x0000000C /* ZMII bridge mode selector mask */
-#define SDR0_ETH_CFG_ZMII_SEL_MII 0x00000000 /* ZMII bridge mode - MII */
-#define SDR0_ETH_CFG_ZMII_SEL_SMII 0x00000004 /* ZMII bridge mode - SMII */
-#define SDR0_ETH_CFG_ZMII_SEL_RMII_10 0x00000008 /* ZMII bridge mode - RMII (10 Mbps) */
-#define SDR0_ETH_CFG_ZMII_SEL_RMII_100 0x0000000C /* ZMII bridge mode - RMII (100 Mbps) */
-#define SDR0_ETH_CFG_GMC1_BRIDGE_SEL 0x00000002 /* GMC Port 1 bridge selector */
-#define SDR0_ETH_CFG_GMC0_BRIDGE_SEL 0x00000001 /* GMC Port 0 bridge selector */
+#define SDR0_ETH_CFG_SGMII3_LPBK 0x00800000 /*SGMII3 port loopback
+ enable */
+#define SDR0_ETH_CFG_SGMII2_LPBK 0x00400000 /*SGMII2 port loopback
+ enable */
+#define SDR0_ETH_CFG_SGMII1_LPBK 0x00200000 /*SGMII1 port loopback
+ enable */
+#define SDR0_ETH_CFG_SGMII0_LPBK 0x00100000 /*SGMII0 port loopback
+ enable */
+#define SDR0_ETH_CFG_SGMII_MASK 0x00070000 /*SGMII Mask */
+#define SDR0_ETH_CFG_SGMII2_ENABLE 0x00040000 /*SGMII2 port enable */
+#define SDR0_ETH_CFG_SGMII1_ENABLE 0x00020000 /*SGMII1 port enable */
+#define SDR0_ETH_CFG_SGMII0_ENABLE 0x00010000 /*SGMII0 port enable */
+#define SDR0_ETH_CFG_TAHOE1_BYPASS 0x00002000 /*TAHOE1 Bypass selector */
+#define SDR0_ETH_CFG_TAHOE0_BYPASS 0x00001000 /*TAHOE0 Bypass selector */
+#define SDR0_ETH_CFG_EMAC3_PHY_CLK_SEL 0x00000800 /*EMAC 3 PHY clock selector*/
+#define SDR0_ETH_CFG_EMAC2_PHY_CLK_SEL 0x00000400 /*EMAC 2 PHY clock selector*/
+#define SDR0_ETH_CFG_EMAC1_PHY_CLK_SEL 0x00000200 /*EMAC 1 PHY clock selector*/
+#define SDR0_ETH_CFG_EMAC0_PHY_CLK_SEL 0x00000100 /*EMAC 0 PHY clock selector*/
+#define SDR0_ETH_CFG_EMAC_2_1_SWAP 0x00000080 /*Swap EMAC2 with EMAC1 */
+#define SDR0_ETH_CFG_EMAC_0_3_SWAP 0x00000040 /*Swap EMAC0 with EMAC3 */
+#define SDR0_ETH_CFG_MDIO_SEL_MASK 0x00000030 /*MDIO source selector mask*/
+#define SDR0_ETH_CFG_MDIO_SEL_EMAC0 0x00000000 /*MDIO source - EMAC0 */
+#define SDR0_ETH_CFG_MDIO_SEL_EMAC1 0x00000010 /*MDIO source - EMAC1 */
+#define SDR0_ETH_CFG_MDIO_SEL_EMAC2 0x00000020 /*MDIO source - EMAC2 */
+#define SDR0_ETH_CFG_MDIO_SEL_EMAC3 0x00000030 /*MDIO source - EMAC3 */
+#define SDR0_ETH_CFG_ZMII_MODE_MASK 0x0000000C /*ZMII bridge mode selector
+ mask */
+#define SDR0_ETH_CFG_ZMII_SEL_MII 0x00000000 /*ZMII bridge mode - MII */
+#define SDR0_ETH_CFG_ZMII_SEL_SMII 0x00000004 /*ZMII bridge mode - SMII */
+#define SDR0_ETH_CFG_ZMII_SEL_RMII_10 0x00000008 /*ZMII bridge mode - RMII
+ (10 Mbps) */
+#define SDR0_ETH_CFG_ZMII_SEL_RMII_100 0x0000000C /*ZMII bridge mode - RMII
+ (100 Mbps) */
+#define SDR0_ETH_CFG_GMC1_BRIDGE_SEL 0x00000002 /*GMC Port 1 bridge
+ selector */
+#define SDR0_ETH_CFG_GMC0_BRIDGE_SEL 0x00000001 /*GMC Port 0 bridge
+ selector */
#define SDR0_ETH_CFG_ZMII_MODE_SHIFT 4
#define SDR0_ETH_CFG_ZMII_MII_MODE 0x00
/* Miscealleneaous Function Reg. (SDR0_MFR) */
#define SDR0_MFR 0x4300
-#define SDR0_MFR_T0TxFL 0x00800000 /* force parity error TAHOE0 Tx FIFO bits 0:63 */
-#define SDR0_MFR_T0TxFH 0x00400000 /* force parity error TAHOE0 Tx FIFO bits 64:127 */
-#define SDR0_MFR_T1TxFL 0x00200000 /* force parity error TAHOE1 Tx FIFO bits 0:63 */
-#define SDR0_MFR_T1TxFH 0x00100000 /* force parity error TAHOE1 Tx FIFO bits 64:127 */
-#define SDR0_MFR_E0TxFL 0x00008000 /* force parity error EMAC0 Tx FIFO bits 0:63 */
-#define SDR0_MFR_E0TxFH 0x00004000 /* force parity error EMAC0 Tx FIFO bits 64:127 */
-#define SDR0_MFR_E0RxFL 0x00002000 /* force parity error EMAC0 Rx FIFO bits 0:63 */
-#define SDR0_MFR_E0RxFH 0x00001000 /* force parity error EMAC0 Rx FIFO bits 64:127 */
-#define SDR0_MFR_E1TxFL 0x00000800 /* force parity error EMAC1 Tx FIFO bits 0:63 */
-#define SDR0_MFR_E1TxFH 0x00000400 /* force parity error EMAC1 Tx FIFO bits 64:127 */
-#define SDR0_MFR_E1RxFL 0x00000200 /* force parity error EMAC1 Rx FIFO bits 0:63 */
-#define SDR0_MFR_E1RxFH 0x00000100 /* force parity error EMAC1 Rx FIFO bits 64:127 */
-#define SDR0_MFR_E2TxFL 0x00000080 /* force parity error EMAC2 Tx FIFO bits 0:63 */
-#define SDR0_MFR_E2TxFH 0x00000040 /* force parity error EMAC2 Tx FIFO bits 64:127 */
-#define SDR0_MFR_E2RxFL 0x00000020 /* force parity error EMAC2 Rx FIFO bits 0:63 */
-#define SDR0_MFR_E2RxFH 0x00000010 /* force parity error EMAC2 Rx FIFO bits 64:127 */
-#define SDR0_MFR_E3TxFL 0x00000008 /* force parity error EMAC3 Tx FIFO bits 0:63 */
-#define SDR0_MFR_E3TxFH 0x00000004 /* force parity error EMAC3 Tx FIFO bits 64:127 */
-#define SDR0_MFR_E3RxFL 0x00000002 /* force parity error EMAC3 Rx FIFO bits 0:63 */
-#define SDR0_MFR_E3RxFH 0x00000001 /* force parity error EMAC3 Rx FIFO bits 64:127 */
+#define SDR0_MFR_T0TxFL 0x00800000 /* force parity error TAHOE0 Tx
+ FIFO bits 0:63 */
+#define SDR0_MFR_T0TxFH 0x00400000 /* force parity error TAHOE0 Tx
+ FIFO bits 64:127 */
+#define SDR0_MFR_T1TxFL 0x00200000 /* force parity error TAHOE1 Tx
+ FIFO bits 0:63 */
+#define SDR0_MFR_T1TxFH 0x00100000 /* force parity error TAHOE1 Tx
+ FIFO bits 64:127 */
+#define SDR0_MFR_E0TxFL 0x00008000 /* force parity error EMAC0 Tx
+ FIFO bits 0:63 */
+#define SDR0_MFR_E0TxFH 0x00004000 /* force parity error EMAC0 Tx
+ FIFO bits 64:127 */
+#define SDR0_MFR_E0RxFL 0x00002000 /* force parity error EMAC0 Rx
+ FIFO bits 0:63 */
+#define SDR0_MFR_E0RxFH 0x00001000 /* force parity error EMAC0 Rx
+ FIFO bits 64:127 */
+#define SDR0_MFR_E1TxFL 0x00000800 /* force parity error EMAC1 Tx
+ FIFO bits 0:63 */
+#define SDR0_MFR_E1TxFH 0x00000400 /* force parity error EMAC1 Tx
+ FIFO bits 64:127 */
+#define SDR0_MFR_E1RxFL 0x00000200 /* force parity error EMAC1 Rx
+ FIFO bits 0:63 */
+#define SDR0_MFR_E1RxFH 0x00000100 /* force parity error EMAC1 Rx
+ FIFO bits 64:127 */
+#define SDR0_MFR_E2TxFL 0x00000080 /* force parity error EMAC2 Tx
+ FIFO bits 0:63 */
+#define SDR0_MFR_E2TxFH 0x00000040 /* force parity error EMAC2 Tx
+ FIFO bits 64:127 */
+#define SDR0_MFR_E2RxFL 0x00000020 /* force parity error EMAC2 Rx
+ FIFO bits 0:63 */
+#define SDR0_MFR_E2RxFH 0x00000010 /* force parity error EMAC2 Rx
+ FIFO bits 64:127 */
+#define SDR0_MFR_E3TxFL 0x00000008 /* force parity error EMAC3 Tx
+ FIFO bits 0:63 */
+#define SDR0_MFR_E3TxFH 0x00000004 /* force parity error EMAC3 Tx
+ FIFO bits 64:127 */
+#define SDR0_MFR_E3RxFL 0x00000002 /* force parity error EMAC3 Rx
+ FIFO bits 0:63 */
+#define SDR0_MFR_E3RxFH 0x00000001 /* force parity error EMAC3 Rx
+ FIFO bits 64:127 */
/* EMACx TX Status Register (SDR0_EMACxTXST)*/
#define SDR0_EMAC0TXST 0x4400
#define SDR0_EMAC2TXST 0x4402
#define SDR0_EMAC3TXST 0x4403
-#define SDR0_EMACxTXST_FUR 0x02000000 /* TX FIFO underrun */
-#define SDR0_EMACxTXST_BC 0x01000000 /* broadcase address */
-#define SDR0_EMACxTXST_MC 0x00800000 /* multicast address */
-#define SDR0_EMACxTXST_UC 0x00400000 /* unicast address */
-#define SDR0_EMACxTXST_FP 0x00200000 /* frame paused by control packet */
-#define SDR0_EMACxTXST_BFCS 0x00100000 /* bad FCS in the transmitted frame */
-#define SDR0_EMACxTXST_CPF 0x00080000 /* TX control pause frame */
-#define SDR0_EMACxTXST_CF 0x00040000 /* TX control frame */
-#define SDR0_EMACxTXST_MSIZ 0x00020000 /* 1024-maxsize bytes transmitted */
-#define SDR0_EMACxTXST_1023 0x00010000 /* 512-1023 bytes transmitted */
-#define SDR0_EMACxTXST_511 0x00008000 /* 256-511 bytes transmitted */
-#define SDR0_EMACxTXST_255 0x00004000 /* 128-255 bytes transmitted */
-#define SDR0_EMACxTXST_127 0x00002000 /* 65-127 bytes transmitted */
-#define SDR0_EMACxTXST_64 0x00001000 /* 64 bytes transmitted */
-#define SDR0_EMACxTXST_SQE 0x00000800 /* SQE indication */
-#define SDR0_EMACxTXST_LOC 0x00000400 /* loss of carrier sense */
-#define SDR0_EMACxTXST_IERR 0x00000080 /* EMAC internal error */
-#define SDR0_EMACxTXST_EDF 0x00000040 /* excessive deferral */
-#define SDR0_EMACxTXST_ECOL 0x00000020 /* excessive collisions */
-#define SDR0_EMACxTXST_LCOL 0x00000010 /* late collision */
-#define SDR0_EMACxTXST_DFFR 0x00000008 /* deferred frame */
-#define SDR0_EMACxTXST_MCOL 0x00000004 /* multiple collision frame */
-#define SDR0_EMACxTXST_SCOL 0x00000002 /* single collision frame */
-#define SDR0_EMACxTXST_TXOK 0x00000001 /* transmit OK */
+#define SDR0_EMACxTXST_FUR 0x02000000 /*TX FIFO underrun */
+#define SDR0_EMACxTXST_BC 0x01000000 /*broadcase address */
+#define SDR0_EMACxTXST_MC 0x00800000 /*multicast address */
+#define SDR0_EMACxTXST_UC 0x00400000 /*unicast address */
+#define SDR0_EMACxTXST_FP 0x00200000 /*frame paused by control packet */
+#define SDR0_EMACxTXST_BFCS 0x00100000 /*bad FCS in the transmitted frame */
+#define SDR0_EMACxTXST_CPF 0x00080000 /*TX control pause frame */
+#define SDR0_EMACxTXST_CF 0x00040000 /*TX control frame */
+#define SDR0_EMACxTXST_MSIZ 0x00020000 /* 1024-maxsize bytes transmitted */
+#define SDR0_EMACxTXST_1023 0x00010000 /*512-1023 bytes transmitted */
+#define SDR0_EMACxTXST_511 0x00008000 /*256-511 bytes transmitted */
+#define SDR0_EMACxTXST_255 0x00004000 /*128-255 bytes transmitted */
+#define SDR0_EMACxTXST_127 0x00002000 /*65-127 bytes transmitted */
+#define SDR0_EMACxTXST_64 0x00001000 /*64 bytes transmitted */
+#define SDR0_EMACxTXST_SQE 0x00000800 /*SQE indication */
+#define SDR0_EMACxTXST_LOC 0x00000400 /*loss of carrier sense */
+#define SDR0_EMACxTXST_IERR 0x00000080 /*EMAC internal error */
+#define SDR0_EMACxTXST_EDF 0x00000040 /*excessive deferral */
+#define SDR0_EMACxTXST_ECOL 0x00000020 /*excessive collisions */
+#define SDR0_EMACxTXST_LCOL 0x00000010 /*late collision */
+#define SDR0_EMACxTXST_DFFR 0x00000008 /*deferred frame */
+#define SDR0_EMACxTXST_MCOL 0x00000004 /*multiple collision frame */
+#define SDR0_EMACxTXST_SCOL 0x00000002 /*single collision frame */
+#define SDR0_EMACxTXST_TXOK 0x00000001 /*transmit OK */
/* EMACx RX Status Register (SDR0_EMACxRXST)*/
#define SDR0_EMAC0RXST 0x4404
#define SDR0_EMACxRXST_F2L 0x00000020 /* frame is to long */
#define SDR0_EMACxRXST_OERR 0x00000010 /* out of range length error */
#define SDR0_EMACxRXST_IERR 0x00000008 /* in range length error */
-#define SDR0_EMACxRXST_LOST 0x00000004 /* frame lost due to internal EMAC receive error */
-#define SDR0_EMACxRXST_BFCS 0x00000002 /* bad FCS in the recieved frame */
+#define SDR0_EMACxRXST_LOST 0x00000004 /* frame lost due to internal
+ EMAC receive error */
+#define SDR0_EMACxRXST_BFCS 0x00000002 /* bad FCS in the recieved frame */
#define SDR0_EMACxRXST_RXOK 0x00000001 /* Recieve OK */
/* EMACx TX Status Register (SDR0_EMACxREJCNT)*/
#define SDR0_MFR_ECS_MASK 0x10000000
#define SDR0_MFR_ECS_INTERNAL 0x10000000
-#define SDR0_MFR_ETH0_CLK_SEL 0x08000000 /* Ethernet0 Clock Select */
-#define SDR0_MFR_ETH1_CLK_SEL 0x04000000 /* Ethernet1 Clock Select */
-#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */
-#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */
-#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */
-#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */
-#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs */
-#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */
-#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */
-#define SDR0_MFR_ERRATA3_EN0 0x00800000
-#define SDR0_MFR_ERRATA3_EN1 0x00400000
+#define SDR0_MFR_ETH0_CLK_SEL 0x08000000 /* Ethernet0 Clock Select */
+#define SDR0_MFR_ETH1_CLK_SEL 0x04000000 /* Ethernet1 Clock Select */
+#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */
+#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */
+#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */
+#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */
+#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs*/
+#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */
+#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */
+#define SDR0_MFR_ERRATA3_EN0 0x00800000
+#define SDR0_MFR_ERRATA3_EN1 0x00400000
#if defined(CONFIG_440GX) /* test-only: only 440GX or 440SPE??? */
-#define SDR0_MFR_PKT_REJ_MASK 0x00300000 /* Pkt Rej. Enable Mask */
-#define SDR0_MFR_PKT_REJ_EN 0x00300000 /* Pkt Rej. Enable on both EMAC3 0-1 */
-#define SDR0_MFR_PKT_REJ_EN0 0x00200000 /* Pkt Rej. Enable on EMAC3(0) */
-#define SDR0_MFR_PKT_REJ_EN1 0x00100000 /* Pkt Rej. Enable on EMAC3(1) */
-#define SDR0_MFR_PKT_REJ_POL 0x00080000 /* Packet Reject Polarity */
+#define SDR0_MFR_PKT_REJ_MASK 0x00300000 /* Pkt Rej. Enable Mask */
+#define SDR0_MFR_PKT_REJ_EN 0x00300000 /* Pkt Rej. Enable on both EMAC3
+ 0-1 */
+#define SDR0_MFR_PKT_REJ_EN0 0x00200000 /* Pkt Rej. Enable on EMAC3(0) */
+#define SDR0_MFR_PKT_REJ_EN1 0x00100000 /* Pkt Rej. Enable on EMAC3(1) */
+#define SDR0_MFR_PKT_REJ_POL 0x00080000 /* Packet Reject Polarity */
#endif
#define SDR0_MFR_ECS_INTERNAL 0x10000000
#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
-#define SDR0_SRST0 0x200
-#define SDR0_SRST0_BGO 0x80000000 /* PLB to OPB bridge */
-#define SDR0_SRST0_PLB4 0x40000000 /* PLB4 arbiter */
-#define SDR0_SRST0_EBC 0x20000000 /* External bus controller */
-#define SDR0_SRST0_OPB 0x10000000 /* OPB arbiter */
-#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/transmitter 0 */
-#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/transmitter 1 */
-#define SDR0_SRST0_IIC0 0x02000000 /* Inter integrated circuit 0 */
-#define SDR0_SRST0_USB2H 0x01000000 /* USB2.0 Host */
-#define SDR0_SRST0_GPIO 0x00800000 /* General purpose I/O */
-#define SDR0_SRST0_GPT 0x00400000 /* General purpose timer */
-#define SDR0_SRST0_DMC 0x00200000 /* DDR SDRAM memory controller */
-#define SDR0_SRST0_PCI 0x00100000 /* PCI */
-#define SDR0_SRST0_EMAC0 0x00080000 /* Ethernet media access controller 0 */
-#define SDR0_SRST0_EMAC1 0x00040000 /* Ethernet media access controller 1 */
-#define SDR0_SRST0_CPM0 0x00020000 /* Clock and power management */
-#define SDR0_SRST0_ZMII 0x00010000 /* ZMII bridge */
-#define SDR0_SRST0_UIC0 0x00008000 /* Universal interrupt controller 0 */
-#define SDR0_SRST0_UIC1 0x00004000 /* Universal interrupt controller 1 */
-#define SDR0_SRST0_IIC1 0x00002000 /* Inter integrated circuit 1 */
-#define SDR0_SRST0_SCP 0x00001000 /* Serial communications port */
-#define SDR0_SRST0_BGI 0x00000800 /* OPB to PLB bridge */
-#define SDR0_SRST0_DMA 0x00000400 /* Direct memory access controller */
-#define SDR0_SRST0_DMAC 0x00000200 /* DMA channel */
-#define SDR0_SRST0_MAL 0x00000100 /* Media access layer */
-#define SDR0_SRST0_USB2D 0x00000080 /* USB2.0 device */
-#define SDR0_SRST0_GPTR 0x00000040 /* General purpose timer */
-#define SDR0_SRST0_P4P3 0x00000010 /* PLB4 to PLB3 bridge */
-#define SDR0_SRST0_P3P4 0x00000008 /* PLB3 to PLB4 bridge */
-#define SDR0_SRST0_PLB3 0x00000004 /* PLB3 arbiter */
-#define SDR0_SRST0_UART2 0x00000002 /* Universal asynchronous receiver/transmitter 2 */
-#define SDR0_SRST0_UART3 0x00000001 /* Universal asynchronous receiver/transmitter 3 */
-
-#define SDR0_SRST1 0x201
-#define SDR0_SRST1_NDFC 0x80000000 /* Nand flash controller */
-#define SDR0_SRST1_OPBA1 0x40000000 /* OPB Arbiter attached to PLB4 */
-#define SDR0_SRST1_P4OPB0 0x20000000 /* PLB4 to OPB Bridge0 */
+#define SDR0_SRST0 0x200
+#define SDR0_SRST0_BGO 0x80000000 /* PLB to OPB bridge */
+#define SDR0_SRST0_PLB4 0x40000000 /* PLB4 arbiter */
+#define SDR0_SRST0_EBC 0x20000000 /* External bus controller */
+#define SDR0_SRST0_OPB 0x10000000 /* OPB arbiter */
+#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/
+ transmitter 0 */
+#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/
+ transmitter 1 */
+#define SDR0_SRST0_IIC0 0x02000000 /* Inter integrated circuit 0 */
+#define SDR0_SRST0_USB2H 0x01000000 /* USB2.0 Host */
+#define SDR0_SRST0_GPIO 0x00800000 /* General purpose I/O */
+#define SDR0_SRST0_GPT 0x00400000 /* General purpose timer */
+#define SDR0_SRST0_DMC 0x00200000 /* DDR SDRAM memory controller */
+#define SDR0_SRST0_PCI 0x00100000 /* PCI */
+#define SDR0_SRST0_EMAC0 0x00080000 /* Ethernet media access controller 0 */
+#define SDR0_SRST0_EMAC1 0x00040000 /* Ethernet media access controller 1 */
+#define SDR0_SRST0_CPM0 0x00020000 /* Clock and power management */
+#define SDR0_SRST0_ZMII 0x00010000 /* ZMII bridge */
+#define SDR0_SRST0_UIC0 0x00008000 /* Universal interrupt controller 0 */
+#define SDR0_SRST0_UIC1 0x00004000 /* Universal interrupt controller 1 */
+#define SDR0_SRST0_IIC1 0x00002000 /* Inter integrated circuit 1 */
+#define SDR0_SRST0_SCP 0x00001000 /* Serial communications port */
+#define SDR0_SRST0_BGI 0x00000800 /* OPB to PLB bridge */
+#define SDR0_SRST0_DMA 0x00000400 /* Direct memory access controller */
+#define SDR0_SRST0_DMAC 0x00000200 /* DMA channel */
+#define SDR0_SRST0_MAL 0x00000100 /* Media access layer */
+#define SDR0_SRST0_USB2D 0x00000080 /* USB2.0 device */
+#define SDR0_SRST0_GPTR 0x00000040 /* General purpose timer */
+#define SDR0_SRST0_P4P3 0x00000010 /* PLB4 to PLB3 bridge */
+#define SDR0_SRST0_P3P4 0x00000008 /* PLB3 to PLB4 bridge */
+#define SDR0_SRST0_PLB3 0x00000004 /* PLB3 arbiter */
+#define SDR0_SRST0_UART2 0x00000002 /* Universal asynchronous receiver/
+ transmitter 2 */
+#define SDR0_SRST0_UART3 0x00000001 /* Universal asynchronous receiver/
+ transmitter 3 */
+
+#define SDR0_SRST1 0x201
+#define SDR0_SRST1_NDFC 0x80000000 /* Nand flash controller */
+#define SDR0_SRST1_OPBA1 0x40000000 /* OPB Arbiter attached to PLB4 */
+#define SDR0_SRST1_P4OPB0 0x20000000 /* PLB4 to OPB Bridge0 */
#define SDR0_SRST1_PLB42OPB0 SDR0_SRST1_P4OPB0
-#define SDR0_SRST1_DMA4 0x10000000 /* DMA to PLB4 */
-#define SDR0_SRST1_DMA4CH 0x08000000 /* DMA Channel to PLB4 */
-#define SDR0_SRST1_OPBA2 0x04000000 /* OPB Arbiter attached to PLB4 USB 2.0 Host */
-#define SDR0_SRST1_OPB2PLB40 0x02000000 /* OPB to PLB4 Bridge attached to USB 2.0 Host */
-#define SDR0_SRST1_PLB42OPB1 0x01000000 /* PLB4 to OPB Bridge attached to USB 2.0 Host */
-#define SDR0_SRST1_CPM1 0x00800000 /* Clock and Power management 1 */
-#define SDR0_SRST1_UIC2 0x00400000 /* Universal Interrupt Controller 2 */
-#define SDR0_SRST1_CRYP0 0x00200000 /* Security Engine */
-#define SDR0_SRST1_USB20PHY 0x00100000 /* USB 2.0 Phy */
-#define SDR0_SRST1_USB2HUTMI 0x00080000 /* USB 2.0 Host UTMI Interface */
-#define SDR0_SRST1_USB2HPHY 0x00040000 /* USB 2.0 Host Phy Interface */
-#define SDR0_SRST1_SRAM0 0x00020000 /* Internal SRAM Controller */
-#define SDR0_SRST1_RGMII0 0x00010000 /* RGMII Bridge */
-#define SDR0_SRST1_ETHPLL 0x00008000 /* Ethernet PLL */
-#define SDR0_SRST1_FPU 0x00004000 /* Floating Point Unit */
-#define SDR0_SRST1_KASU0 0x00002000 /* Kasumi Engine */
+#define SDR0_SRST1_DMA4 0x10000000 /* DMA to PLB4 */
+#define SDR0_SRST1_DMA4CH 0x08000000 /* DMA Channel to PLB4 */
+#define SDR0_SRST1_OPBA2 0x04000000 /* OPB Arbiter attached to PLB4
+ USB 2.0 Host */
+#define SDR0_SRST1_OPB2PLB40 0x02000000 /* OPB to PLB4 Bridge attached to
+ USB 2.0 Host */
+#define SDR0_SRST1_PLB42OPB1 0x01000000 /* PLB4 to OPB Bridge attached to
+ USB 2.0 Host */
+#define SDR0_SRST1_CPM1 0x00800000 /* Clock and Power management 1 */
+#define SDR0_SRST1_UIC2 0x00400000 /* Universal Interrupt Controller 2*/
+#define SDR0_SRST1_CRYP0 0x00200000 /* Security Engine */
+#define SDR0_SRST1_USB20PHY 0x00100000 /* USB 2.0 Phy */
+#define SDR0_SRST1_USB2HUTMI 0x00080000 /* USB 2.0 Host UTMI Interface */
+#define SDR0_SRST1_USB2HPHY 0x00040000 /* USB 2.0 Host Phy Interface */
+#define SDR0_SRST1_SRAM0 0x00020000 /* Internal SRAM Controller */
+#define SDR0_SRST1_RGMII0 0x00010000 /* RGMII Bridge */
+#define SDR0_SRST1_ETHPLL 0x00008000 /* Ethernet PLL */
+#define SDR0_SRST1_FPU 0x00004000 /* Floating Point Unit */
+#define SDR0_SRST1_KASU0 0x00002000 /* Kasumi Engine */
#define SDR0_EMAC0RXST 0x00004301 /* */
#define SDR0_EMAC0TXST 0x00004302 /* */
#define SDR0_SRST0_PLB4 0x40000000 /* PLB4 arbiter */
#define SDR0_SRST0_EBC 0x20000000 /* External bus controller */
#define SDR0_SRST0_OPB 0x10000000 /* OPB arbiter */
-#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/transmitter 0 */
-#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/transmitter 1 */
+#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/
+ transmitter 0 */
+#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/
+ transmitter 1 */
#define SDR0_SRST0_IIC0 0x02000000 /* Inter integrated circuit 0 */
#define SDR0_SRST0_IIC1 0x01000000 /* Inter integrated circuit 1 */
#define SDR0_SRST0_GPIO0 0x00800000 /* General purpose I/O 0 */
#define SDR0_SRST0_UIC2 0x00001000 /* Universal interrupt controller 2*/
#define SDR0_SRST0_UIC3 0x00000800 /* Universal interrupt controller 3*/
#define SDR0_SRST0_OCM 0x00000400 /* Universal interrupt controller 0*/
-#define SDR0_SRST0_UART2 0x00000200 /* Universal asynchronous receiver/transmitter 2 */
+#define SDR0_SRST0_UART2 0x00000200 /* Universal asynchronous receiver/
+ transmitter 2 */
#define SDR0_SRST0_MAL 0x00000100 /* Media access layer */
#define SDR0_SRST0_GPTR 0x00000040 /* General purpose timer */
#define SDR0_SRST0_L2CACHE 0x00000004 /* L2 Cache */
-#define SDR0_SRST0_UART3 0x00000002 /* Universal asynchronous receiver/transmitter 3 */
+#define SDR0_SRST0_UART3 0x00000002 /* Universal asynchronous receiver/
+ transmitter 3 */
#define SDR0_SRST0_GPIO1 0x00000001 /* General purpose I/O 1 */
#define SDR0_SRST1 0x201
#define SDR0_SRST1_PLBARB 0x20000000 /* PLB Arbiter */
#define SDR0_SRST1_EIPPKP 0x10000000 /* EIPPPKP */
#define SDR0_SRST1_EIP94 0x08000000 /* EIP 94 */
-#define SDR0_SRST1_EMAC0 0x04000000 /* Ethernet media access controller 0 */
-#define SDR0_SRST1_EMAC1 0x02000000 /* Ethernet media access controller 1 */
-#define SDR0_SRST1_EMAC2 0x01000000 /* Ethernet media access controller 2 */
-#define SDR0_SRST1_EMAC3 0x00800000 /* Ethernet media access controller 3 */
+#define SDR0_SRST1_EMAC0 0x04000000 /* Ethernet media access
+ controller 0 */
+#define SDR0_SRST1_EMAC1 0x02000000 /* Ethernet media access
+ controller 1 */
+#define SDR0_SRST1_EMAC2 0x01000000 /* Ethernet media access
+ controller 2 */
+#define SDR0_SRST1_EMAC3 0x00800000 /* Ethernet media access
+ controller 3 */
#define SDR0_SRST1_ZMII 0x00400000 /* Ethernet ZMII/RMII/SMII */
#define SDR0_SRST1_RGMII0 0x00200000 /* Ethernet RGMII/RTBI 0 */
#define SDR0_SRST1_RGMII1 0x00100000 /* Ethernet RGMII/RTBI 1 */
#define SDR0_SRST1_DMA4 0x00080000 /* DMA to PLB4 */
#define SDR0_SRST1_DMA4CH 0x00040000 /* DMA Channel to PLB4 */
#define SDR0_SRST1_SATAPHY 0x00020000 /* Serial ATA PHY */
-#define SDR0_SRST1_SRIODEV 0x00010000 /* Serial Rapid IO core, PCS, and serdes */
+#define SDR0_SRST1_SRIODEV 0x00010000 /* Serial Rapid IO core, PCS, and
+ serdes */
#define SDR0_SRST1_SRIOPCS 0x00008000 /* Serial Rapid IO core and PCS */
#define SDR0_SRST1_NDFC 0x00004000 /* Nand flash controller */
#define SDR0_SRST1_SRIOPLB 0x00002000 /* Serial Rapid IO PLB */
#else /* !CONFIG_440GX or CONFIG_440EP or CONFIG_440GR */
#define PLLSYS0_ENG_MASK 0x80000000 /* 0 = SysClk, 1 = PLL VCO */
#define PLLSYS0_SRC_MASK 0x40000000 /* 0 = PLL A, 1 = PLL B */
-#define PLLSYS0_SEL_MASK 0x38000000 /* 0 = PLL, 1 = CPU, 5 = PerClk */
+#define PLLSYS0_SEL_MASK 0x38000000 /* 0 = PLL, 1 = CPU, 5 = PerClk */
#define PLLSYS0_TUNE_MASK 0x07fe0000 /* PLL Tune bits */
#define PLLSYS0_FB_DIV_MASK 0x0001f000 /* Feedback divisor */
#define PLLSYS0_FWD_DIV_A_MASK 0x00000f00 /* Fwd Div A */
#define PLLSYS0_PRI_DIV_B_MASK 0x0000001c /* PLL Primary Divisor B */
#define PLLSYS0_OPB_DIV_MASK 0x00000003 /* OPB Divisor */
-#define PLLC_ENG_MASK 0x20000000 /* PLL primary forward divisor source */
+#define PLLC_ENG_MASK 0x20000000 /* PLL primary forward divisor source */
#define PLLC_SRC_MASK 0x20000000 /* PLL feedback source */
#define PLLD_FBDV_MASK 0x1f000000 /* PLL Feedback Divisor */
#define PLLD_FWDVA_MASK 0x000f0000 /* PLL Forward Divisor A */
/* PCI Local Configuration Registers
--------------------------------- */
-#define PCI_MMIO_LCR_BASE (CONFIG_SYS_PCI_BASE + 0x0f400000) /* Real => 0x0EF400000 */
+#define PCI_MMIO_LCR_BASE (CONFIG_SYS_PCI_BASE + 0x0f400000) /* Real =>
+ 0x0EF400000 */
/* PCI Master Local Configuration Registers */
-#define PCIL0_PMM0LA (PCI_MMIO_LCR_BASE + 0x00) /* PMM0 Local Address */
-#define PCIL0_PMM0MA (PCI_MMIO_LCR_BASE + 0x04) /* PMM0 Mask/Attribute */
-#define PCIL0_PMM0PCILA (PCI_MMIO_LCR_BASE + 0x08) /* PMM0 PCI Low Address */
-#define PCIL0_PMM0PCIHA (PCI_MMIO_LCR_BASE + 0x0C) /* PMM0 PCI High Address */
-#define PCIL0_PMM1LA (PCI_MMIO_LCR_BASE + 0x10) /* PMM1 Local Address */
-#define PCIL0_PMM1MA (PCI_MMIO_LCR_BASE + 0x14) /* PMM1 Mask/Attribute */
-#define PCIL0_PMM1PCILA (PCI_MMIO_LCR_BASE + 0x18) /* PMM1 PCI Low Address */
-#define PCIL0_PMM1PCIHA (PCI_MMIO_LCR_BASE + 0x1C) /* PMM1 PCI High Address */
-#define PCIL0_PMM2LA (PCI_MMIO_LCR_BASE + 0x20) /* PMM2 Local Address */
-#define PCIL0_PMM2MA (PCI_MMIO_LCR_BASE + 0x24) /* PMM2 Mask/Attribute */
-#define PCIL0_PMM2PCILA (PCI_MMIO_LCR_BASE + 0x28) /* PMM2 PCI Low Address */
-#define PCIL0_PMM2PCIHA (PCI_MMIO_LCR_BASE + 0x2C) /* PMM2 PCI High Address */
+#define PCIL0_PMM0LA (PCI_MMIO_LCR_BASE + 0x00) /* PMM0 Local Address */
+#define PCIL0_PMM0MA (PCI_MMIO_LCR_BASE + 0x04) /* PMM0 Mask/Attribute */
+#define PCIL0_PMM0PCILA (PCI_MMIO_LCR_BASE + 0x08) /* PMM0 PCI Low Address */
+#define PCIL0_PMM0PCIHA (PCI_MMIO_LCR_BASE + 0x0C) /* PMM0 PCI High Address */
+#define PCIL0_PMM1LA (PCI_MMIO_LCR_BASE + 0x10) /* PMM1 Local Address */
+#define PCIL0_PMM1MA (PCI_MMIO_LCR_BASE + 0x14) /* PMM1 Mask/Attribute */
+#define PCIL0_PMM1PCILA (PCI_MMIO_LCR_BASE + 0x18) /* PMM1 PCI Low Address */
+#define PCIL0_PMM1PCIHA (PCI_MMIO_LCR_BASE + 0x1C) /* PMM1 PCI High Address */
+#define PCIL0_PMM2LA (PCI_MMIO_LCR_BASE + 0x20) /* PMM2 Local Address */
+#define PCIL0_PMM2MA (PCI_MMIO_LCR_BASE + 0x24) /* PMM2 Mask/Attribute */
+#define PCIL0_PMM2PCILA (PCI_MMIO_LCR_BASE + 0x28) /* PMM2 PCI Low Address */
+#define PCIL0_PMM2PCIHA (PCI_MMIO_LCR_BASE + 0x2C) /* PMM2 PCI High Address */
/* PCI Target Local Configuration Registers */
-#define PCIL0_PTM1MS (PCI_MMIO_LCR_BASE + 0x30) /* PTM1 Memory Size/Attribute */
-#define PCIL0_PTM1LA (PCI_MMIO_LCR_BASE + 0x34) /* PTM1 Local Addr. Reg */
-#define PCIL0_PTM2MS (PCI_MMIO_LCR_BASE + 0x38) /* PTM2 Memory Size/Attribute */
-#define PCIL0_PTM2LA (PCI_MMIO_LCR_BASE + 0x3C) /* PTM2 Local Addr. Reg */
+#define PCIL0_PTM1MS (PCI_MMIO_LCR_BASE + 0x30) /* PTM1 Memory Size/
+ Attribute */
+#define PCIL0_PTM1LA (PCI_MMIO_LCR_BASE + 0x34) /* PTM1 Local Addr. Reg */
+#define PCIL0_PTM2MS (PCI_MMIO_LCR_BASE + 0x38) /* PTM2 Memory Size/
+ Attribute */
+#define PCIL0_PTM2LA (PCI_MMIO_LCR_BASE + 0x3C) /* PTM2 Local Addr. Reg */
#else
#define PCIL0_RES2 (PCIL0_CFGBASE + 0x0038 )
#define PCIL0_INTLN (PCIL0_CFGBASE + PCI_INTERRUPT_LINE )
#define PCIL0_INTPN (PCIL0_CFGBASE + PCI_INTERRUPT_PIN )
+#define SDR0_EMACxTXST_FUR 0x02000000 /* TX FIFO underrun */
+#define SDR0_EMACxTXST_BC 0x01000000 /* broadcase address */
+#define SDR0_EMACxTXST_MC 0x00800000 /* multicast address */
+#define SDR0_EMACxTXST_UC 0x00400000 /* unicast address */
+#define SDR0_EMACxTXST_FP 0x00200000 /* frame paused by control packet */
+#define SDR0_EMACxTXST_BFCS 0x00100000 /* bad FCS in the transmitted frame*/
+#define SDR0_EMACxTXST_CPF 0x00080000 /* TX control pause frame */
+#define SDR0_EMACxTXST_CF 0x00040000 /* TX control frame */
+#define SDR0_EMACxTXST_MSIZ 0x00020000 /* 1024-maxsize bytes transmitted */
+#define SDR0_EMACxTXST_1023 0x00010000 /* 512-1023 bytes transmitted */
+#define SDR0_EMACxTXST_511 0x00008000 /* 256-511 bytes transmitted */
+#define SDR0_EMACxTXST_255 0x00004000 /* 128-255 bytes transmitted */
+#define SDR0_EMACxTXST_127 0x00002000 /* 65-127 bytes transmitted */
+#define SDR0_EMACxTXST_64 0x00001000 /* 64 bytes transmitted */
+#define SDR0_EMACxTXST_SQE 0x00000800 /* SQE indication */
+#define SDR0_EMACxTXST_LOC 0x00000400 /* loss of carrier sense */
+#define SDR0_EMACxTXST_IERR 0x00000080 /* EMAC internal error */
+#define SDR0_EMACxTXST_EDF 0x00000040 /* excessive deferral */
+#define SDR0_EMACxTXST_ECOL 0x00000020 /* excessive collisions */
+#define SDR0_EMACxTXST_LCOL 0x00000010 /* late collision */
+#define SDR0_EMACxTXST_DFFR 0x00000008 /* deferred frame */
+#define SDR0_EMACxTXST_MCOL 0x00000004 /* multiple collision frame */
+#define SDR0_EMACxTXST_SCOL 0x00000002 /* single collision frame */
+#define SDR0_EMACxTXST_TXOK 0x00000001 /* transmit OK */
+
#define PCIL0_MINGNT (PCIL0_CFGBASE + PCI_MIN_GNT )
#define PCIL0_MAXLTNCY (PCIL0_CFGBASE + PCI_MAX_LAT )
#define USB2D0_INTRIN (USB2D0_BASE + 0x00000000)
-#define USB2D0_INTRIN (USB2D0_BASE + 0x00000000) /* Interrupt register for Endpoint 0 plus IN Endpoints 1 to 3 */
-#define USB2D0_POWER (USB2D0_BASE + 0x00000000) /* Power management register */
-#define USB2D0_FADDR (USB2D0_BASE + 0x00000000) /* Function address register */
-#define USB2D0_INTRINE (USB2D0_BASE + 0x00000000) /* Interrupt enable register for USB2D0_INTRIN */
-#define USB2D0_INTROUT (USB2D0_BASE + 0x00000000) /* Interrupt register for OUT Endpoints 1 to 3 */
-#define USB2D0_INTRUSBE (USB2D0_BASE + 0x00000000) /* Interrupt enable register for USB2D0_INTRUSB */
-#define USB2D0_INTRUSB (USB2D0_BASE + 0x00000000) /* Interrupt register for common USB interrupts */
-#define USB2D0_INTROUTE (USB2D0_BASE + 0x00000000) /* Interrupt enable register for IntrOut */
-#define USB2D0_TSTMODE (USB2D0_BASE + 0x00000000) /* Enables the USB 2.0 test modes */
-#define USB2D0_INDEX (USB2D0_BASE + 0x00000000) /* Index register for selecting the Endpoint status/control registers */
+#define USB2D0_INTRIN (USB2D0_BASE + 0x00000000) /* Interrupt register for
+ Endpoint 0 plus IN Endpoints 1 to 3 */
+#define USB2D0_POWER (USB2D0_BASE + 0x00000000) /* Power management
+ register */
+#define USB2D0_FADDR (USB2D0_BASE + 0x00000000) /* Function address
+ register */
+#define USB2D0_INTRINE (USB2D0_BASE + 0x00000000) /* Interrupt enable
+ register for USB2D0_INTRIN */
+#define USB2D0_INTROUT (USB2D0_BASE + 0x00000000) /* Interrupt register for
+ OUT Endpoints 1 to 3 */
+#define USB2D0_INTRUSBE (USB2D0_BASE + 0x00000000) /* Interrupt enable
+ register for USB2D0_INTRUSB */
+#define USB2D0_INTRUSB (USB2D0_BASE + 0x00000000) /* Interrupt register for
+ common USB interrupts */
+#define USB2D0_INTROUTE (USB2D0_BASE + 0x00000000) /* Interrupt enable
+ register for IntrOut */
+#define USB2D0_TSTMODE (USB2D0_BASE + 0x00000000) /* Enables the USB 2.0
+ test modes */
+#define USB2D0_INDEX (USB2D0_BASE + 0x00000000) /* Index register for
+ selecting the Endpoint status/control registers */
#define USB2D0_FRAME (USB2D0_BASE + 0x00000000) /* Frame number */
-#define USB2D0_INCSR0 (USB2D0_BASE + 0x00000000) /* Control Status register for Endpoint 0. (Index register set to select Endpoint 0) */
-#define USB2D0_INCSR (USB2D0_BASE + 0x00000000) /* Control Status register for IN Endpoint. (Index register set to select Endpoints 13) */
-#define USB2D0_INMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet size for IN Endpoint. (Index register set to select Endpoints 13) */
-#define USB2D0_OUTCSR (USB2D0_BASE + 0x00000000) /* Control Status register for OUT Endpoint. (Index register set to select Endpoints 13) */
-#define USB2D0_OUTMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet size for OUT Endpoint. (Index register set to select Endpoints 13) */
-#define USB2D0_OUTCOUNT0 (USB2D0_BASE + 0x00000000) /* Number of received bytes in Endpoint 0 FIFO. (Index register set to select Endpoint 0) */
-#define USB2D0_OUTCOUNT (USB2D0_BASE + 0x00000000) /* Number of bytes in OUT Endpoint FIFO. (Index register set to select Endpoints 13) */
+#define USB2D0_INCSR0 (USB2D0_BASE + 0x00000000) /* Control Status
+ register for Endpoint 0. (Index register set to select Endpoint 0) */
+#define USB2D0_INCSR (USB2D0_BASE + 0x00000000) /* Control Status
+ register for IN Endpoint. (Index register set to select Endpoints 13) */
+#define USB2D0_INMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet
+ size for IN Endpoint. (Index register set to select Endpoints 13) */
+#define USB2D0_OUTCSR (USB2D0_BASE + 0x00000000) /* Control Status
+ register for OUT Endpoint. (Index register set to select Endpoints 13) */
+#define USB2D0_OUTMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet
+ size for OUT Endpoint. (Index register set to select Endpoints 13) */
+#define USB2D0_OUTCOUNT0 (USB2D0_BASE + 0x00000000) /* Number of received
+ bytes in Endpoint 0 FIFO. (Index register set to select Endpoint 0) */
+#define USB2D0_OUTCOUNT (USB2D0_BASE + 0x00000000) /* Number of bytes in
+ OUT Endpoint FIFO. (Index register set to select Endpoints 13) */
#endif
/******************************************************************************
#if defined(CONFIG_440GP) || defined(CONFIG_440GX) || \
defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
defined(CONFIG_460SX)
-#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000700)
+#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000700)
-#define GPIO0_OR (GPIO0_BASE+0x0)
-#define GPIO0_TCR (GPIO0_BASE+0x4)
-#define GPIO0_ODR (GPIO0_BASE+0x18)
-#define GPIO0_IR (GPIO0_BASE+0x1C)
+#define GPIO0_OR (GPIO0_BASE+0x0)
+#define GPIO0_TCR (GPIO0_BASE+0x4)
+#define GPIO0_ODR (GPIO0_BASE+0x18)
+#define GPIO0_IR (GPIO0_BASE+0x1C)
#endif /* CONFIG_440GP */
#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT)
-#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000B00)
-#define GPIO1_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000C00)
-
-#define GPIO0_OR (GPIO0_BASE+0x0)
-#define GPIO0_TCR (GPIO0_BASE+0x4)
-#define GPIO0_OSRL (GPIO0_BASE+0x8)
-#define GPIO0_OSRH (GPIO0_BASE+0xC)
-#define GPIO0_TSRL (GPIO0_BASE+0x10)
-#define GPIO0_TSRH (GPIO0_BASE+0x14)
-#define GPIO0_ODR (GPIO0_BASE+0x18)
-#define GPIO0_IR (GPIO0_BASE+0x1C)
-#define GPIO0_RR1 (GPIO0_BASE+0x20)
-#define GPIO0_RR2 (GPIO0_BASE+0x24)
-#define GPIO0_RR3 (GPIO0_BASE+0x28)
-#define GPIO0_ISR1L (GPIO0_BASE+0x30)
-#define GPIO0_ISR1H (GPIO0_BASE+0x34)
-#define GPIO0_ISR2L (GPIO0_BASE+0x38)
-#define GPIO0_ISR2H (GPIO0_BASE+0x3C)
-#define GPIO0_ISR3L (GPIO0_BASE+0x40)
-#define GPIO0_ISR3H (GPIO0_BASE+0x44)
-
-#define GPIO1_OR (GPIO1_BASE+0x0)
-#define GPIO1_TCR (GPIO1_BASE+0x4)
-#define GPIO1_OSRL (GPIO1_BASE+0x8)
-#define GPIO1_OSRH (GPIO1_BASE+0xC)
-#define GPIO1_TSRL (GPIO1_BASE+0x10)
-#define GPIO1_TSRH (GPIO1_BASE+0x14)
-#define GPIO1_ODR (GPIO1_BASE+0x18)
-#define GPIO1_IR (GPIO1_BASE+0x1C)
-#define GPIO1_RR1 (GPIO1_BASE+0x20)
-#define GPIO1_RR2 (GPIO1_BASE+0x24)
-#define GPIO1_RR3 (GPIO1_BASE+0x28)
-#define GPIO1_ISR1L (GPIO1_BASE+0x30)
-#define GPIO1_ISR1H (GPIO1_BASE+0x34)
-#define GPIO1_ISR2L (GPIO1_BASE+0x38)
-#define GPIO1_ISR2H (GPIO1_BASE+0x3C)
-#define GPIO1_ISR3L (GPIO1_BASE+0x40)
-#define GPIO1_ISR3H (GPIO1_BASE+0x44)
+#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000B00)
+#define GPIO1_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000C00)
+
+#define GPIO0_OR (GPIO0_BASE+0x0)
+#define GPIO0_TCR (GPIO0_BASE+0x4)
+#define GPIO0_OSRL (GPIO0_BASE+0x8)
+#define GPIO0_OSRH (GPIO0_BASE+0xC)
+#define GPIO0_TSRL (GPIO0_BASE+0x10)
+#define GPIO0_TSRH (GPIO0_BASE+0x14)
+#define GPIO0_ODR (GPIO0_BASE+0x18)
+#define GPIO0_IR (GPIO0_BASE+0x1C)
+#define GPIO0_RR1 (GPIO0_BASE+0x20)
+#define GPIO0_RR2 (GPIO0_BASE+0x24)
+#define GPIO0_RR3 (GPIO0_BASE+0x28)
+#define GPIO0_ISR1L (GPIO0_BASE+0x30)
+#define GPIO0_ISR1H (GPIO0_BASE+0x34)
+#define GPIO0_ISR2L (GPIO0_BASE+0x38)
+#define GPIO0_ISR2H (GPIO0_BASE+0x3C)
+#define GPIO0_ISR3L (GPIO0_BASE+0x40)
+#define GPIO0_ISR3H (GPIO0_BASE+0x44)
+
+#define GPIO1_OR (GPIO1_BASE+0x0)
+#define GPIO1_TCR (GPIO1_BASE+0x4)
+#define GPIO1_OSRL (GPIO1_BASE+0x8)
+#define GPIO1_OSRH (GPIO1_BASE+0xC)
+#define GPIO1_TSRL (GPIO1_BASE+0x10)
+#define GPIO1_TSRH (GPIO1_BASE+0x14)
+#define GPIO1_ODR (GPIO1_BASE+0x18)
+#define GPIO1_IR (GPIO1_BASE+0x1C)
+#define GPIO1_RR1 (GPIO1_BASE+0x20)
+#define GPIO1_RR2 (GPIO1_BASE+0x24)
+#define GPIO1_RR3 (GPIO1_BASE+0x28)
+#define GPIO1_ISR1L (GPIO1_BASE+0x30)
+#define GPIO1_ISR1H (GPIO1_BASE+0x34)
+#define GPIO1_ISR2L (GPIO1_BASE+0x38)
+#define GPIO1_ISR2H (GPIO1_BASE+0x3C)
+#define GPIO1_ISR3L (GPIO1_BASE+0x40)
+#define GPIO1_ISR3H (GPIO1_BASE+0x44)
#endif
#ifndef __ASSEMBLY__
projects / oweals / u-boot.git / commitdiff