Merge branch 'master' of git://git.denx.de/u-boot-net
authorTom Rini <trini@konsulko.com>
Mon, 7 Nov 2016 18:16:00 +0000 (13:16 -0500)
committerTom Rini <trini@konsulko.com>
Mon, 7 Nov 2016 18:16:00 +0000 (13:16 -0500)
15 files changed:
arch/arm/dts/tegra186-p2771-0000.dtsi
arch/arm/dts/tegra186.dtsi
arch/arm/mach-tegra/board186.c
arch/arm/mach-tegra/tegra186/Makefile
arch/arm/mach-tegra/tegra186/nvtboot_board.c [new file with mode: 0644]
configs/p2771-0000-000_defconfig
configs/p2771-0000-500_defconfig
doc/device-tree-bindings/net/snps,dwc-qos-ethernet.txt [new file with mode: 0644]
drivers/net/Kconfig
drivers/net/Makefile
drivers/net/dwc_eth_qos.c [new file with mode: 0644]
drivers/net/mvgbe.c
drivers/net/phy/micrel.c
include/micrel.h
net/eth-uclass.c

index 6e071082f9ee9754665f08c1da90e77b4fceaf9a..54b2539ff45644814dbbe4145d1b7fd15d086c3d 100644 (file)
                reg = <0x0 0x80000000 0x0 0x60000000>;
        };
 
+       ethernet@2490000 {
+               status = "okay";
+               phy-reset-gpios = <&gpio_main TEGRA_MAIN_GPIO(M, 4) GPIO_ACTIVE_LOW>;
+       };
+
        i2c@3160000 {
                status = "okay";
        };
index f878b65325101859b7205ebc93a5cacead2194f2..dd9e3b869de716c43bcb8f559207adfbf2cb6ddb 100644 (file)
                #interrupt-cells = <2>;
        };
 
+       ethernet@2490000 {
+               compatible = "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10";
+               reg = <0x0 0x02490000 0x0 0x10000>;
+               interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
+               clocks = <&bpmp TEGRA186_CLK_AXI_CBB>,
+                       <&bpmp TEGRA186_CLK_EQOS_AXI>,
+                       <&bpmp TEGRA186_CLK_EQOS_RX>,
+                       <&bpmp TEGRA186_CLK_EQOS_PTP_REF>,
+                       <&bpmp TEGRA186_CLK_EQOS_TX>;
+               clock-names = "slave_bus",
+                       "master_bus",
+                       "rx",
+                       "ptp_ref",
+                       "tx";
+               resets = <&bpmp TEGRA186_RESET_EQOS>;
+               reset-names = "eqos";
+               phy-mode = "rgmii";
+               status = "disabled";
+       };
+
        uarta: serial@3100000 {
                compatible = "nvidia,tegra186-uart", "nvidia,tegra20-uart";
                reg = <0x0 0x03100000 0x0 0x10000>;
index a071758afe7b7b132f7d828eb81133b8d0690b52..691c3fd98dabdec9e3450914b99a959511dd8c19 100644 (file)
@@ -24,7 +24,12 @@ int board_init(void)
        return tegra_board_init();
 }
 
-int board_late_init(void)
+__weak int tegra_soc_board_init_late(void)
 {
        return 0;
 }
+
+int board_late_init(void)
+{
+       return tegra_soc_board_init_late();
+}
index 7f46a057bca1bd4cfc3978b2c558753d6771392e..56f3378ecea373b938433e70b47682fd796f8326 100644 (file)
@@ -4,5 +4,6 @@
 
 obj-y += ../board186.o
 obj-y += cache.o
+obj-y += nvtboot_board.o
 obj-y += nvtboot_ll.o
 obj-y += nvtboot_mem.o
diff --git a/arch/arm/mach-tegra/tegra186/nvtboot_board.c b/arch/arm/mach-tegra/tegra186/nvtboot_board.c
new file mode 100644 (file)
index 0000000..1d78346
--- /dev/null
@@ -0,0 +1,54 @@
+/*
+ * Copyright (c) 2016, NVIDIA CORPORATION.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <fdt_support.h>
+#include <fdtdec.h>
+#include <asm/arch/tegra.h>
+
+extern unsigned long nvtboot_boot_x0;
+
+/*
+ * Attempt to use /chosen/nvidia,ether-mac in the nvtboot DTB to U-Boot's
+ * ethaddr environment variable if possible.
+ */
+static int set_ethaddr_from_nvtboot(void)
+{
+       const void *nvtboot_blob = (void *)nvtboot_boot_x0;
+       int ret, node, len;
+       const u32 *prop;
+
+       /* Already a valid address in the environment? If so, keep it */
+       if (getenv("ethaddr"))
+               return 0;
+
+       node = fdt_path_offset(nvtboot_blob, "/chosen");
+       if (node < 0) {
+               printf("Can't find /chosen node in nvtboot DTB\n");
+               return node;
+       }
+       prop = fdt_getprop(nvtboot_blob, node, "nvidia,ether-mac", &len);
+       if (!prop) {
+               printf("Can't find nvidia,ether-mac property in nvtboot DTB\n");
+               return -ENOENT;
+       }
+
+       ret = setenv("ethaddr", (void *)prop);
+       if (ret) {
+               printf("Failed to set ethaddr from nvtboot DTB: %d\n", ret);
+               return ret;
+       }
+
+       return 0;
+}
+
+int tegra_soc_board_init_late(void)
+{
+       /* Ignore errors here; not all cases care about Ethernet addresses */
+       set_ethaddr_from_nvtboot();
+
+       return 0;
+}
index f638117c8951500de2757c7822b6683f66d18738..61bb3a119627c9690510c1020b0dd2ee709ccdec 100644 (file)
@@ -30,6 +30,7 @@ CONFIG_CMD_FS_GENERIC=y
 # CONFIG_BLK is not set
 CONFIG_TEGRA186_BPMP_I2C=y
 # CONFIG_DM_MMC_OPS is not set
+CONFIG_DWC_ETH_QOS=y
 CONFIG_E1000=y
 CONFIG_RTL8169=y
 CONFIG_PCI=y
index baeb8f33cd1e5a08a5d0cafde4e9542be03a5de8..79f4808274bbe1c12c56c01c9f20c34181203133 100644 (file)
@@ -30,6 +30,7 @@ CONFIG_CMD_FS_GENERIC=y
 # CONFIG_BLK is not set
 CONFIG_TEGRA186_BPMP_I2C=y
 # CONFIG_DM_MMC_OPS is not set
+CONFIG_DWC_ETH_QOS=y
 CONFIG_E1000=y
 CONFIG_RTL8169=y
 CONFIG_PCI=y
diff --git a/doc/device-tree-bindings/net/snps,dwc-qos-ethernet.txt b/doc/device-tree-bindings/net/snps,dwc-qos-ethernet.txt
new file mode 100644 (file)
index 0000000..d93f71c
--- /dev/null
@@ -0,0 +1,166 @@
+* Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC)
+
+This binding supports the Synopsys Designware Ethernet QoS (Quality Of Service)
+IP block. The IP supports multiple options for bus type, clocking and reset
+structure, and feature list. Consequently, a number of properties and list
+entries in properties are marked as optional, or only required in specific HW
+configurations.
+
+Required properties:
+- compatible: One of:
+  - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10"
+    Represents the IP core when integrated into the Axis ARTPEC-6 SoC.
+  - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10"
+    Represents the IP core when integrated into the NVIDIA Tegra186 SoC.
+  - "snps,dwc-qos-ethernet-4.10"
+    This combination is deprecated. It should be treated as equivalent to
+    "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10". It is supported to be
+    compatible with earlier revisions of this binding.
+- reg: Address and length of the register set for the device
+- clocks: Phandle and clock specifiers for each entry in clock-names, in the
+  same order. See ../clock/clock-bindings.txt.
+- clock-names: May contain any/all of the following depending on the IP
+  configuration, in any order:
+  - "tx"
+    The EQOS transmit path clock. The HW signal name is clk_tx_i.
+    In some configurations (e.g. GMII/RGMII), this clock also drives the PHY TX
+    path. In other configurations, other clocks (such as tx_125, rmii) may
+    drive the PHY TX path.
+  - "rx"
+    The EQOS receive path clock. The HW signal name is clk_rx_i.
+    In some configurations (e.g. GMII/RGMII), this clock is derived from the
+    PHY's RX clock output. In other configurations, other clocks (such as
+    rx_125, rmii) may drive the EQOS RX path.
+    In cases where the PHY clock is directly fed into the EQOS receive path
+    without intervening logic, the DT need not represent this clock, since it
+    is assumed to be fully under the control of the PHY device/driver. In
+    cases where SoC integration adds additional logic to this path, such as a
+    SW-controlled clock gate, this clock should be represented in DT.
+  - "slave_bus"
+    The CPU/slave-bus (CSR) interface clock. This applies to any bus type;
+    APB, AHB, AXI, etc. The HW signal name is hclk_i (AHB) or clk_csr_i (other
+    buses).
+  - "master_bus"
+    The master bus interface clock. Only required in configurations that use a
+    separate clock for the master and slave bus interfaces. The HW signal name
+    is hclk_i (AHB) or aclk_i (AXI).
+  - "ptp_ref"
+    The PTP reference clock. The HW signal name is clk_ptp_ref_i.
+  - "phy_ref_clk"
+    This clock is deprecated and should not be used by new compatible values.
+    It is equivalent to "tx".
+  - "apb_pclk"
+    This clock is deprecated and should not be used by new compatible values.
+    It is equivalent to "slave_bus".
+
+  Note: Support for additional IP configurations may require adding the
+  following clocks to this list in the future: clk_rx_125_i, clk_tx_125_i,
+  clk_pmarx_0_i, clk_pmarx1_i, clk_rmii_i, clk_revmii_rx_i, clk_revmii_tx_i.
+  Configurations exist where multiple similar clocks are used at once, e.g. all
+  of clk_rx_125_i, clk_pmarx_0_i, clk_pmarx1_i. For this reason it is best to
+  extend the binding with a separate clock-names entry for each of those RX
+  clocks, rather than repurposing the existing "rx" clock-names entry as a
+  generic/logical clock in a similar fashion to "master_bus" and "slave_bus".
+  This will allow easy support for configurations that support multiple PHY
+  interfaces using a mux, and hence need to have explicit control over
+  specific RX clocks.
+
+  The following compatible values require the following set of clocks:
+  - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10":
+    - "slave_bus"
+    - "master_bus"
+    - "rx"
+    - "tx"
+    - "ptp_ref"
+  - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10":
+    - "slave_bus"
+    - "master_bus"
+    - "tx"
+    - "ptp_ref"
+  - "snps,dwc-qos-ethernet-4.10" (deprecated):
+    - "phy_ref_clk"
+    - "apb_clk"
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupts: Should contain the core's combined interrupt signal
+- phy-mode: See ethernet.txt file in the same directory
+- resets: Phandle and reset specifiers for each entry in reset-names, in the
+  same order. See ../reset/reset.txt.
+- reset-names: May contain any/all of the following depending on the IP
+  configuration, in any order:
+  - "eqos". The reset to the entire module. The HW signal name is hreset_n
+    (AHB) or aresetn_i (AXI).
+
+  The following compatible values require the following set of resets:
+  (the reset properties may be omitted if empty)
+  - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10":
+    - "eqos".
+  - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10":
+    - None.
+  - "snps,dwc-qos-ethernet-4.10" (deprecated):
+    - None.
+
+Optional properties:
+- dma-coherent: Present if dma operations are coherent
+- mac-address: See ethernet.txt in the same directory
+- local-mac-address: See ethernet.txt in the same directory
+- phy-reset-gpios: Phandle and specifier for any GPIO used to reset the PHY.
+  See ../gpio/gpio.txt.
+- snps,en-lpi: If present it enables use of the AXI low-power interface
+- snps,write-requests: Number of write requests that the AXI port can issue.
+  It depends on the SoC configuration.
+- snps,read-requests: Number of read requests that the AXI port can issue.
+  It depends on the SoC configuration.
+- snps,burst-map: Bitmap of allowed AXI burst lengts, with the LSB
+  representing 4, then 8 etc.
+- snps,txpbl: DMA Programmable burst length for the TX DMA
+- snps,rxpbl: DMA Programmable burst length for the RX DMA
+- snps,en-tx-lpi-clockgating: Enable gating of the MAC TX clock during
+  TX low-power mode.
+- phy-handle: See ethernet.txt file in the same directory
+- mdio device tree subnode: When the GMAC has a phy connected to its local
+    mdio, there must be device tree subnode with the following
+    required properties:
+    - compatible: Must be "snps,dwc-qos-ethernet-mdio".
+    - #address-cells: Must be <1>.
+    - #size-cells: Must be <0>.
+
+    For each phy on the mdio bus, there must be a node with the following
+    fields:
+
+    - reg: phy id used to communicate to phy.
+    - device_type: Must be "ethernet-phy".
+    - fixed-mode device tree subnode: see fixed-link.txt in the same directory
+
+Examples:
+ethernet2@40010000 {
+       clock-names = "phy_ref_clk", "apb_pclk";
+       clocks = <&clkc 17>, <&clkc 15>;
+       compatible = "snps,dwc-qos-ethernet-4.10";
+       interrupt-parent = <&intc>;
+       interrupts = <0x0 0x1e 0x4>;
+       reg = <0x40010000 0x4000>;
+       phy-handle = <&phy2>;
+       phy-mode = "gmii";
+       phy-reset-gpios = <&gpioctlr 43 GPIO_ACTIVE_LOW>;
+
+       snps,en-tx-lpi-clockgating;
+       snps,en-lpi;
+       snps,write-requests = <2>;
+       snps,read-requests = <16>;
+       snps,burst-map = <0x7>;
+       snps,txpbl = <8>;
+       snps,rxpbl = <2>;
+
+       dma-coherent;
+
+       mdio {
+               #address-cells = <0x1>;
+               #size-cells = <0x0>;
+               phy2: phy@1 {
+                       compatible = "ethernet-phy-ieee802.3-c22";
+                       device_type = "ethernet-phy";
+                       reg = <0x1>;
+               };
+       };
+};
index 7b9961de476e73f7a45cf4c73a8cc8fa6d69bd46..f25d3ffa9b87c3dbfccf91d70e343c5f9efb9a6a 100644 (file)
@@ -64,6 +64,17 @@ config ALTERA_TSE
          Please find details on the "Triple-Speed Ethernet MegaCore Function
          Resource Center" of Altera.
 
+config DWC_ETH_QOS
+       bool "Synopsys DWC Ethernet QOS device support"
+       depends on DM_ETH
+       select PHYLIB
+       help
+         This driver supports the Synopsys Designware Ethernet QOS (Quality
+         Of Service) IP block. The IP supports many options for bus type,
+         clocking/reset structure, and feature list. This driver currently
+         supports the specific configuration used in NVIDIA's Tegra186 chip,
+         but should be extensible to other combinations quite easily.
+
 config E1000
        bool "Intel PRO/1000 Gigabit Ethernet support"
        help
index a4485266d45732a66279fbc32bcdee23632e2552..9a7bfc6d5b0507e730ee7de6a5965cafc020d73e 100644 (file)
@@ -76,3 +76,4 @@ obj-$(CONFIG_FSL_MC_ENET) += ldpaa_eth/
 obj-$(CONFIG_FSL_MEMAC) += fm/memac_phy.o
 obj-$(CONFIG_VSC9953) += vsc9953.o
 obj-$(CONFIG_PIC32_ETH) += pic32_mdio.o pic32_eth.o
+obj-$(CONFIG_DWC_ETH_QOS) += dwc_eth_qos.o
diff --git a/drivers/net/dwc_eth_qos.c b/drivers/net/dwc_eth_qos.c
new file mode 100644 (file)
index 0000000..81eeba2
--- /dev/null
@@ -0,0 +1,1552 @@
+/*
+ * Copyright (c) 2016, NVIDIA CORPORATION.
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ *
+ * Portions based on U-Boot's rtl8169.c.
+ */
+
+/*
+ * This driver supports the Synopsys Designware Ethernet QOS (Quality Of
+ * Service) IP block. The IP supports multiple options for bus type, clocking/
+ * reset structure, and feature list.
+ *
+ * The driver is written such that generic core logic is kept separate from
+ * configuration-specific logic. Code that interacts with configuration-
+ * specific resources is split out into separate functions to avoid polluting
+ * common code. If/when this driver is enhanced to support multiple
+ * configurations, the core code should be adapted to call all configuration-
+ * specific functions through function pointers, with the definition of those
+ * function pointers being supplied by struct udevice_id eqos_ids[]'s .data
+ * field.
+ *
+ * The following configurations are currently supported:
+ * tegra186:
+ *    NVIDIA's Tegra186 chip. This configuration uses an AXI master/DMA bus, an
+ *    AHB slave/register bus, contains the DMA, MTL, and MAC sub-blocks, and
+ *    supports a single RGMII PHY. This configuration also has SW control over
+ *    all clock and reset signals to the HW block.
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <errno.h>
+#include <memalign.h>
+#include <miiphy.h>
+#include <net.h>
+#include <netdev.h>
+#include <phy.h>
+#include <reset.h>
+#include <wait_bit.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+
+/* Core registers */
+
+#define EQOS_MAC_REGS_BASE 0x000
+struct eqos_mac_regs {
+       uint32_t configuration;                         /* 0x000 */
+       uint32_t unused_004[(0x070 - 0x004) / 4];       /* 0x004 */
+       uint32_t q0_tx_flow_ctrl;                       /* 0x070 */
+       uint32_t unused_070[(0x090 - 0x074) / 4];       /* 0x074 */
+       uint32_t rx_flow_ctrl;                          /* 0x090 */
+       uint32_t unused_094;                            /* 0x094 */
+       uint32_t txq_prty_map0;                         /* 0x098 */
+       uint32_t unused_09c;                            /* 0x09c */
+       uint32_t rxq_ctrl0;                             /* 0x0a0 */
+       uint32_t unused_0a4;                            /* 0x0a4 */
+       uint32_t rxq_ctrl2;                             /* 0x0a8 */
+       uint32_t unused_0ac[(0x0dc - 0x0ac) / 4];       /* 0x0ac */
+       uint32_t us_tic_counter;                        /* 0x0dc */
+       uint32_t unused_0e0[(0x11c - 0x0e0) / 4];       /* 0x0e0 */
+       uint32_t hw_feature0;                           /* 0x11c */
+       uint32_t hw_feature1;                           /* 0x120 */
+       uint32_t hw_feature2;                           /* 0x124 */
+       uint32_t unused_128[(0x200 - 0x128) / 4];       /* 0x128 */
+       uint32_t mdio_address;                          /* 0x200 */
+       uint32_t mdio_data;                             /* 0x204 */
+       uint32_t unused_208[(0x300 - 0x208) / 4];       /* 0x208 */
+       uint32_t address0_high;                         /* 0x300 */
+       uint32_t address0_low;                          /* 0x304 */
+};
+
+#define EQOS_MAC_CONFIGURATION_GPSLCE                  BIT(23)
+#define EQOS_MAC_CONFIGURATION_CST                     BIT(21)
+#define EQOS_MAC_CONFIGURATION_ACS                     BIT(20)
+#define EQOS_MAC_CONFIGURATION_WD                      BIT(19)
+#define EQOS_MAC_CONFIGURATION_JD                      BIT(17)
+#define EQOS_MAC_CONFIGURATION_JE                      BIT(16)
+#define EQOS_MAC_CONFIGURATION_PS                      BIT(15)
+#define EQOS_MAC_CONFIGURATION_FES                     BIT(14)
+#define EQOS_MAC_CONFIGURATION_DM                      BIT(13)
+#define EQOS_MAC_CONFIGURATION_TE                      BIT(1)
+#define EQOS_MAC_CONFIGURATION_RE                      BIT(0)
+
+#define EQOS_MAC_Q0_TX_FLOW_CTRL_PT_SHIFT              16
+#define EQOS_MAC_Q0_TX_FLOW_CTRL_PT_MASK               0xffff
+#define EQOS_MAC_Q0_TX_FLOW_CTRL_TFE                   BIT(1)
+
+#define EQOS_MAC_RX_FLOW_CTRL_RFE                      BIT(0)
+
+#define EQOS_MAC_TXQ_PRTY_MAP0_PSTQ0_SHIFT             0
+#define EQOS_MAC_TXQ_PRTY_MAP0_PSTQ0_MASK              0xff
+
+#define EQOS_MAC_RXQ_CTRL0_RXQ0EN_SHIFT                        0
+#define EQOS_MAC_RXQ_CTRL0_RXQ0EN_MASK                 3
+#define EQOS_MAC_RXQ_CTRL0_RXQ0EN_NOT_ENABLED          0
+#define EQOS_MAC_RXQ_CTRL0_RXQ0EN_ENABLED_DCB          2
+
+#define EQOS_MAC_RXQ_CTRL2_PSRQ0_SHIFT                 0
+#define EQOS_MAC_RXQ_CTRL2_PSRQ0_MASK                  0xff
+
+#define EQOS_MAC_HW_FEATURE1_TXFIFOSIZE_SHIFT          6
+#define EQOS_MAC_HW_FEATURE1_TXFIFOSIZE_MASK           0x1f
+#define EQOS_MAC_HW_FEATURE1_RXFIFOSIZE_SHIFT          0
+#define EQOS_MAC_HW_FEATURE1_RXFIFOSIZE_MASK           0x1f
+
+#define EQOS_MAC_MDIO_ADDRESS_PA_SHIFT                 21
+#define EQOS_MAC_MDIO_ADDRESS_RDA_SHIFT                        16
+#define EQOS_MAC_MDIO_ADDRESS_CR_SHIFT                 8
+#define EQOS_MAC_MDIO_ADDRESS_CR_20_35                 2
+#define EQOS_MAC_MDIO_ADDRESS_SKAP                     BIT(4)
+#define EQOS_MAC_MDIO_ADDRESS_GOC_SHIFT                        2
+#define EQOS_MAC_MDIO_ADDRESS_GOC_READ                 3
+#define EQOS_MAC_MDIO_ADDRESS_GOC_WRITE                        1
+#define EQOS_MAC_MDIO_ADDRESS_C45E                     BIT(1)
+#define EQOS_MAC_MDIO_ADDRESS_GB                       BIT(0)
+
+#define EQOS_MAC_MDIO_DATA_GD_MASK                     0xffff
+
+#define EQOS_MTL_REGS_BASE 0xd00
+struct eqos_mtl_regs {
+       uint32_t txq0_operation_mode;                   /* 0xd00 */
+       uint32_t unused_d04;                            /* 0xd04 */
+       uint32_t txq0_debug;                            /* 0xd08 */
+       uint32_t unused_d0c[(0xd18 - 0xd0c) / 4];       /* 0xd0c */
+       uint32_t txq0_quantum_weight;                   /* 0xd18 */
+       uint32_t unused_d1c[(0xd30 - 0xd1c) / 4];       /* 0xd1c */
+       uint32_t rxq0_operation_mode;                   /* 0xd30 */
+       uint32_t unused_d34;                            /* 0xd34 */
+       uint32_t rxq0_debug;                            /* 0xd38 */
+};
+
+#define EQOS_MTL_TXQ0_OPERATION_MODE_TQS_SHIFT         16
+#define EQOS_MTL_TXQ0_OPERATION_MODE_TQS_MASK          0x1ff
+#define EQOS_MTL_TXQ0_OPERATION_MODE_TXQEN_SHIFT       2
+#define EQOS_MTL_TXQ0_OPERATION_MODE_TXQEN_MASK                3
+#define EQOS_MTL_TXQ0_OPERATION_MODE_TXQEN_ENABLED     2
+#define EQOS_MTL_TXQ0_OPERATION_MODE_TSF               BIT(1)
+#define EQOS_MTL_TXQ0_OPERATION_MODE_FTQ               BIT(0)
+
+#define EQOS_MTL_TXQ0_DEBUG_TXQSTS                     BIT(4)
+#define EQOS_MTL_TXQ0_DEBUG_TRCSTS_SHIFT               1
+#define EQOS_MTL_TXQ0_DEBUG_TRCSTS_MASK                        3
+
+#define EQOS_MTL_RXQ0_OPERATION_MODE_RQS_SHIFT         20
+#define EQOS_MTL_RXQ0_OPERATION_MODE_RQS_MASK          0x3ff
+#define EQOS_MTL_RXQ0_OPERATION_MODE_RFD_SHIFT         14
+#define EQOS_MTL_RXQ0_OPERATION_MODE_RFD_MASK          0x3f
+#define EQOS_MTL_RXQ0_OPERATION_MODE_RFA_SHIFT         8
+#define EQOS_MTL_RXQ0_OPERATION_MODE_RFA_MASK          0x3f
+#define EQOS_MTL_RXQ0_OPERATION_MODE_EHFC              BIT(7)
+#define EQOS_MTL_RXQ0_OPERATION_MODE_RSF               BIT(5)
+
+#define EQOS_MTL_RXQ0_DEBUG_PRXQ_SHIFT                 16
+#define EQOS_MTL_RXQ0_DEBUG_PRXQ_MASK                  0x7fff
+#define EQOS_MTL_RXQ0_DEBUG_RXQSTS_SHIFT               4
+#define EQOS_MTL_RXQ0_DEBUG_RXQSTS_MASK                        3
+
+#define EQOS_DMA_REGS_BASE 0x1000
+struct eqos_dma_regs {
+       uint32_t mode;                                  /* 0x1000 */
+       uint32_t sysbus_mode;                           /* 0x1004 */
+       uint32_t unused_1008[(0x1100 - 0x1008) / 4];    /* 0x1008 */
+       uint32_t ch0_control;                           /* 0x1100 */
+       uint32_t ch0_tx_control;                        /* 0x1104 */
+       uint32_t ch0_rx_control;                        /* 0x1108 */
+       uint32_t unused_110c;                           /* 0x110c */
+       uint32_t ch0_txdesc_list_haddress;              /* 0x1110 */
+       uint32_t ch0_txdesc_list_address;               /* 0x1114 */
+       uint32_t ch0_rxdesc_list_haddress;              /* 0x1118 */
+       uint32_t ch0_rxdesc_list_address;               /* 0x111c */
+       uint32_t ch0_txdesc_tail_pointer;               /* 0x1120 */
+       uint32_t unused_1124;                           /* 0x1124 */
+       uint32_t ch0_rxdesc_tail_pointer;               /* 0x1128 */
+       uint32_t ch0_txdesc_ring_length;                /* 0x112c */
+       uint32_t ch0_rxdesc_ring_length;                /* 0x1130 */
+};
+
+#define EQOS_DMA_MODE_SWR                              BIT(0)
+
+#define EQOS_DMA_SYSBUS_MODE_RD_OSR_LMT_SHIFT          16
+#define EQOS_DMA_SYSBUS_MODE_RD_OSR_LMT_MASK           0xf
+#define EQOS_DMA_SYSBUS_MODE_EAME                      BIT(11)
+#define EQOS_DMA_SYSBUS_MODE_BLEN16                    BIT(3)
+#define EQOS_DMA_SYSBUS_MODE_BLEN8                     BIT(2)
+#define EQOS_DMA_SYSBUS_MODE_BLEN4                     BIT(1)
+
+#define EQOS_DMA_CH0_CONTROL_PBLX8                     BIT(16)
+
+#define EQOS_DMA_CH0_TX_CONTROL_TXPBL_SHIFT            16
+#define EQOS_DMA_CH0_TX_CONTROL_TXPBL_MASK             0x3f
+#define EQOS_DMA_CH0_TX_CONTROL_OSP                    BIT(4)
+#define EQOS_DMA_CH0_TX_CONTROL_ST                     BIT(0)
+
+#define EQOS_DMA_CH0_RX_CONTROL_RXPBL_SHIFT            16
+#define EQOS_DMA_CH0_RX_CONTROL_RXPBL_MASK             0x3f
+#define EQOS_DMA_CH0_RX_CONTROL_RBSZ_SHIFT             1
+#define EQOS_DMA_CH0_RX_CONTROL_RBSZ_MASK              0x3fff
+#define EQOS_DMA_CH0_RX_CONTROL_SR                     BIT(0)
+
+/* These registers are Tegra186-specific */
+#define EQOS_TEGRA186_REGS_BASE 0x8800
+struct eqos_tegra186_regs {
+       uint32_t sdmemcomppadctrl;                      /* 0x8800 */
+       uint32_t auto_cal_config;                       /* 0x8804 */
+       uint32_t unused_8808;                           /* 0x8808 */
+       uint32_t auto_cal_status;                       /* 0x880c */
+};
+
+#define EQOS_SDMEMCOMPPADCTRL_PAD_E_INPUT_OR_E_PWRD    BIT(31)
+
+#define EQOS_AUTO_CAL_CONFIG_START                     BIT(31)
+#define EQOS_AUTO_CAL_CONFIG_ENABLE                    BIT(29)
+
+#define EQOS_AUTO_CAL_STATUS_ACTIVE                    BIT(31)
+
+/* Descriptors */
+
+#define EQOS_DESCRIPTOR_WORDS  4
+#define EQOS_DESCRIPTOR_SIZE   (EQOS_DESCRIPTOR_WORDS * 4)
+/* We assume ARCH_DMA_MINALIGN >= 16; 16 is the EQOS HW minimum */
+#define EQOS_DESCRIPTOR_ALIGN  ARCH_DMA_MINALIGN
+#define EQOS_DESCRIPTORS_TX    4
+#define EQOS_DESCRIPTORS_RX    4
+#define EQOS_DESCRIPTORS_NUM   (EQOS_DESCRIPTORS_TX + EQOS_DESCRIPTORS_RX)
+#define EQOS_DESCRIPTORS_SIZE  ALIGN(EQOS_DESCRIPTORS_NUM * \
+                                     EQOS_DESCRIPTOR_SIZE, ARCH_DMA_MINALIGN)
+#define EQOS_BUFFER_ALIGN      ARCH_DMA_MINALIGN
+#define EQOS_MAX_PACKET_SIZE   ALIGN(1568, ARCH_DMA_MINALIGN)
+#define EQOS_RX_BUFFER_SIZE    (EQOS_DESCRIPTORS_RX * EQOS_MAX_PACKET_SIZE)
+
+/*
+ * Warn if the cache-line size is larger than the descriptor size. In such
+ * cases the driver will likely fail because the CPU needs to flush the cache
+ * when requeuing RX buffers, therefore descriptors written by the hardware
+ * may be discarded. Architectures with full IO coherence, such as x86, do not
+ * experience this issue, and hence are excluded from this condition.
+ *
+ * This can be fixed by defining CONFIG_SYS_NONCACHED_MEMORY which will cause
+ * the driver to allocate descriptors from a pool of non-cached memory.
+ */
+#if EQOS_DESCRIPTOR_SIZE < ARCH_DMA_MINALIGN
+#if !defined(CONFIG_SYS_NONCACHED_MEMORY) && \
+       !defined(CONFIG_SYS_DCACHE_OFF) && !defined(CONFIG_X86)
+#warning Cache line size is larger than descriptor size
+#endif
+#endif
+
+struct eqos_desc {
+       u32 des0;
+       u32 des1;
+       u32 des2;
+       u32 des3;
+};
+
+#define EQOS_DESC3_OWN         BIT(31)
+#define EQOS_DESC3_FD          BIT(29)
+#define EQOS_DESC3_LD          BIT(28)
+#define EQOS_DESC3_BUF1V       BIT(24)
+
+struct eqos_config {
+       bool reg_access_always_ok;
+};
+
+struct eqos_priv {
+       struct udevice *dev;
+       const struct eqos_config *config;
+       fdt_addr_t regs;
+       struct eqos_mac_regs *mac_regs;
+       struct eqos_mtl_regs *mtl_regs;
+       struct eqos_dma_regs *dma_regs;
+       struct eqos_tegra186_regs *tegra186_regs;
+       struct reset_ctl reset_ctl;
+       struct gpio_desc phy_reset_gpio;
+       struct clk clk_master_bus;
+       struct clk clk_rx;
+       struct clk clk_ptp_ref;
+       struct clk clk_tx;
+       struct clk clk_slave_bus;
+       struct mii_dev *mii;
+       struct phy_device *phy;
+       void *descs;
+       struct eqos_desc *tx_descs;
+       struct eqos_desc *rx_descs;
+       int tx_desc_idx, rx_desc_idx;
+       void *tx_dma_buf;
+       void *rx_dma_buf;
+       void *rx_pkt;
+       bool started;
+       bool reg_access_ok;
+};
+
+/*
+ * TX and RX descriptors are 16 bytes. This causes problems with the cache
+ * maintenance on CPUs where the cache-line size exceeds the size of these
+ * descriptors. What will happen is that when the driver receives a packet
+ * it will be immediately requeued for the hardware to reuse. The CPU will
+ * therefore need to flush the cache-line containing the descriptor, which
+ * will cause all other descriptors in the same cache-line to be flushed
+ * along with it. If one of those descriptors had been written to by the
+ * device those changes (and the associated packet) will be lost.
+ *
+ * To work around this, we make use of non-cached memory if available. If
+ * descriptors are mapped uncached there's no need to manually flush them
+ * or invalidate them.
+ *
+ * Note that this only applies to descriptors. The packet data buffers do
+ * not have the same constraints since they are 1536 bytes large, so they
+ * are unlikely to share cache-lines.
+ */
+static void *eqos_alloc_descs(unsigned int num)
+{
+#ifdef CONFIG_SYS_NONCACHED_MEMORY
+       return (void *)noncached_alloc(EQOS_DESCRIPTORS_SIZE,
+                                     EQOS_DESCRIPTOR_ALIGN);
+#else
+       return memalign(EQOS_DESCRIPTOR_ALIGN, EQOS_DESCRIPTORS_SIZE);
+#endif
+}
+
+static void eqos_free_descs(void *descs)
+{
+#ifdef CONFIG_SYS_NONCACHED_MEMORY
+       /* FIXME: noncached_alloc() has no opposite */
+#else
+       free(descs);
+#endif
+}
+
+static void eqos_inval_desc(void *desc)
+{
+#ifndef CONFIG_SYS_NONCACHED_MEMORY
+       unsigned long start = (unsigned long)desc & ~(ARCH_DMA_MINALIGN - 1);
+       unsigned long end = ALIGN(start + EQOS_DESCRIPTOR_SIZE,
+                                 ARCH_DMA_MINALIGN);
+
+       invalidate_dcache_range(start, end);
+#endif
+}
+
+static void eqos_flush_desc(void *desc)
+{
+#ifndef CONFIG_SYS_NONCACHED_MEMORY
+       flush_cache((unsigned long)desc, EQOS_DESCRIPTOR_SIZE);
+#endif
+}
+
+static void eqos_inval_buffer(void *buf, size_t size)
+{
+       unsigned long start = (unsigned long)buf & ~(ARCH_DMA_MINALIGN - 1);
+       unsigned long end = ALIGN(start + size, ARCH_DMA_MINALIGN);
+
+       invalidate_dcache_range(start, end);
+}
+
+static void eqos_flush_buffer(void *buf, size_t size)
+{
+       flush_cache((unsigned long)buf, size);
+}
+
+static int eqos_mdio_wait_idle(struct eqos_priv *eqos)
+{
+       return wait_for_bit(__func__, &eqos->mac_regs->mdio_address,
+                           EQOS_MAC_MDIO_ADDRESS_GB, false, 1000000, true);
+}
+
+static int eqos_mdio_read(struct mii_dev *bus, int mdio_addr, int mdio_devad,
+                         int mdio_reg)
+{
+       struct eqos_priv *eqos = bus->priv;
+       u32 val;
+       int ret;
+
+       debug("%s(dev=%p, addr=%x, reg=%d):\n", __func__, eqos->dev, mdio_addr,
+             mdio_reg);
+
+       ret = eqos_mdio_wait_idle(eqos);
+       if (ret) {
+               error("MDIO not idle at entry");
+               return ret;
+       }
+
+       val = readl(&eqos->mac_regs->mdio_address);
+       val &= EQOS_MAC_MDIO_ADDRESS_SKAP |
+               EQOS_MAC_MDIO_ADDRESS_C45E;
+       val |= (mdio_addr << EQOS_MAC_MDIO_ADDRESS_PA_SHIFT) |
+               (mdio_reg << EQOS_MAC_MDIO_ADDRESS_RDA_SHIFT) |
+               (EQOS_MAC_MDIO_ADDRESS_CR_20_35 <<
+                EQOS_MAC_MDIO_ADDRESS_CR_SHIFT) |
+               (EQOS_MAC_MDIO_ADDRESS_GOC_READ <<
+                EQOS_MAC_MDIO_ADDRESS_GOC_SHIFT) |
+               EQOS_MAC_MDIO_ADDRESS_GB;
+       writel(val, &eqos->mac_regs->mdio_address);
+
+       udelay(10);
+
+       ret = eqos_mdio_wait_idle(eqos);
+       if (ret) {
+               error("MDIO read didn't complete");
+               return ret;
+       }
+
+       val = readl(&eqos->mac_regs->mdio_data);
+       val &= EQOS_MAC_MDIO_DATA_GD_MASK;
+
+       debug("%s: val=%x\n", __func__, val);
+
+       return val;
+}
+
+static int eqos_mdio_write(struct mii_dev *bus, int mdio_addr, int mdio_devad,
+                          int mdio_reg, u16 mdio_val)
+{
+       struct eqos_priv *eqos = bus->priv;
+       u32 val;
+       int ret;
+
+       debug("%s(dev=%p, addr=%x, reg=%d, val=%x):\n", __func__, eqos->dev,
+             mdio_addr, mdio_reg, mdio_val);
+
+       ret = eqos_mdio_wait_idle(eqos);
+       if (ret) {
+               error("MDIO not idle at entry");
+               return ret;
+       }
+
+       writel(mdio_val, &eqos->mac_regs->mdio_data);
+
+       val = readl(&eqos->mac_regs->mdio_address);
+       val &= EQOS_MAC_MDIO_ADDRESS_SKAP |
+               EQOS_MAC_MDIO_ADDRESS_C45E;
+       val |= (mdio_addr << EQOS_MAC_MDIO_ADDRESS_PA_SHIFT) |
+               (mdio_reg << EQOS_MAC_MDIO_ADDRESS_RDA_SHIFT) |
+               (EQOS_MAC_MDIO_ADDRESS_CR_20_35 <<
+                EQOS_MAC_MDIO_ADDRESS_CR_SHIFT) |
+               (EQOS_MAC_MDIO_ADDRESS_GOC_WRITE <<
+                EQOS_MAC_MDIO_ADDRESS_GOC_SHIFT) |
+               EQOS_MAC_MDIO_ADDRESS_GB;
+       writel(val, &eqos->mac_regs->mdio_address);
+
+       udelay(10);
+
+       ret = eqos_mdio_wait_idle(eqos);
+       if (ret) {
+               error("MDIO read didn't complete");
+               return ret;
+       }
+
+       return 0;
+}
+
+static int eqos_start_clks_tegra186(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       int ret;
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       ret = clk_enable(&eqos->clk_slave_bus);
+       if (ret < 0) {
+               error("clk_enable(clk_slave_bus) failed: %d", ret);
+               goto err;
+       }
+
+       ret = clk_enable(&eqos->clk_master_bus);
+       if (ret < 0) {
+               error("clk_enable(clk_master_bus) failed: %d", ret);
+               goto err_disable_clk_slave_bus;
+       }
+
+       ret = clk_enable(&eqos->clk_rx);
+       if (ret < 0) {
+               error("clk_enable(clk_rx) failed: %d", ret);
+               goto err_disable_clk_master_bus;
+       }
+
+       ret = clk_enable(&eqos->clk_ptp_ref);
+       if (ret < 0) {
+               error("clk_enable(clk_ptp_ref) failed: %d", ret);
+               goto err_disable_clk_rx;
+       }
+
+       ret = clk_set_rate(&eqos->clk_ptp_ref, 125 * 1000 * 1000);
+       if (ret < 0) {
+               error("clk_set_rate(clk_ptp_ref) failed: %d", ret);
+               goto err_disable_clk_ptp_ref;
+       }
+
+       ret = clk_enable(&eqos->clk_tx);
+       if (ret < 0) {
+               error("clk_enable(clk_tx) failed: %d", ret);
+               goto err_disable_clk_ptp_ref;
+       }
+
+       debug("%s: OK\n", __func__);
+       return 0;
+
+err_disable_clk_ptp_ref:
+       clk_disable(&eqos->clk_ptp_ref);
+err_disable_clk_rx:
+       clk_disable(&eqos->clk_rx);
+err_disable_clk_master_bus:
+       clk_disable(&eqos->clk_master_bus);
+err_disable_clk_slave_bus:
+       clk_disable(&eqos->clk_slave_bus);
+err:
+       debug("%s: FAILED: %d\n", __func__, ret);
+       return ret;
+}
+
+void eqos_stop_clks_tegra186(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       clk_disable(&eqos->clk_tx);
+       clk_disable(&eqos->clk_ptp_ref);
+       clk_disable(&eqos->clk_rx);
+       clk_disable(&eqos->clk_master_bus);
+       clk_disable(&eqos->clk_slave_bus);
+
+       debug("%s: OK\n", __func__);
+}
+
+static int eqos_start_resets_tegra186(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       int ret;
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       ret = dm_gpio_set_value(&eqos->phy_reset_gpio, 1);
+       if (ret < 0) {
+               error("dm_gpio_set_value(phy_reset, assert) failed: %d", ret);
+               return ret;
+       }
+
+       udelay(2);
+
+       ret = dm_gpio_set_value(&eqos->phy_reset_gpio, 0);
+       if (ret < 0) {
+               error("dm_gpio_set_value(phy_reset, deassert) failed: %d", ret);
+               return ret;
+       }
+
+       ret = reset_assert(&eqos->reset_ctl);
+       if (ret < 0) {
+               error("reset_assert() failed: %d", ret);
+               return ret;
+       }
+
+       udelay(2);
+
+       ret = reset_deassert(&eqos->reset_ctl);
+       if (ret < 0) {
+               error("reset_deassert() failed: %d", ret);
+               return ret;
+       }
+
+       debug("%s: OK\n", __func__);
+       return 0;
+}
+
+static int eqos_stop_resets_tegra186(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+
+       reset_assert(&eqos->reset_ctl);
+       dm_gpio_set_value(&eqos->phy_reset_gpio, 1);
+
+       return 0;
+}
+
+static int eqos_calibrate_pads_tegra186(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       int ret;
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       setbits_le32(&eqos->tegra186_regs->sdmemcomppadctrl,
+                    EQOS_SDMEMCOMPPADCTRL_PAD_E_INPUT_OR_E_PWRD);
+
+       udelay(1);
+
+       setbits_le32(&eqos->tegra186_regs->auto_cal_config,
+                    EQOS_AUTO_CAL_CONFIG_START | EQOS_AUTO_CAL_CONFIG_ENABLE);
+
+       ret = wait_for_bit(__func__, &eqos->tegra186_regs->auto_cal_status,
+                          EQOS_AUTO_CAL_STATUS_ACTIVE, true, 10, false);
+       if (ret) {
+               error("calibrate didn't start");
+               goto failed;
+       }
+
+       ret = wait_for_bit(__func__, &eqos->tegra186_regs->auto_cal_status,
+                          EQOS_AUTO_CAL_STATUS_ACTIVE, false, 10, false);
+       if (ret) {
+               error("calibrate didn't finish");
+               goto failed;
+       }
+
+       ret = 0;
+
+failed:
+       clrbits_le32(&eqos->tegra186_regs->sdmemcomppadctrl,
+                    EQOS_SDMEMCOMPPADCTRL_PAD_E_INPUT_OR_E_PWRD);
+
+       debug("%s: returns %d\n", __func__, ret);
+
+       return ret;
+}
+
+static int eqos_disable_calibration_tegra186(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       clrbits_le32(&eqos->tegra186_regs->auto_cal_config,
+                    EQOS_AUTO_CAL_CONFIG_ENABLE);
+
+       return 0;
+}
+
+static ulong eqos_get_tick_clk_rate_tegra186(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+
+       return clk_get_rate(&eqos->clk_slave_bus);
+}
+
+static int eqos_set_full_duplex(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       setbits_le32(&eqos->mac_regs->configuration, EQOS_MAC_CONFIGURATION_DM);
+
+       return 0;
+}
+
+static int eqos_set_half_duplex(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       clrbits_le32(&eqos->mac_regs->configuration, EQOS_MAC_CONFIGURATION_DM);
+
+       /* WAR: Flush TX queue when switching to half-duplex */
+       setbits_le32(&eqos->mtl_regs->txq0_operation_mode,
+                    EQOS_MTL_TXQ0_OPERATION_MODE_FTQ);
+
+       return 0;
+}
+
+static int eqos_set_gmii_speed(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       clrbits_le32(&eqos->mac_regs->configuration,
+                    EQOS_MAC_CONFIGURATION_PS | EQOS_MAC_CONFIGURATION_FES);
+
+       return 0;
+}
+
+static int eqos_set_mii_speed_100(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       setbits_le32(&eqos->mac_regs->configuration,
+                    EQOS_MAC_CONFIGURATION_PS | EQOS_MAC_CONFIGURATION_FES);
+
+       return 0;
+}
+
+static int eqos_set_mii_speed_10(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       clrsetbits_le32(&eqos->mac_regs->configuration,
+                       EQOS_MAC_CONFIGURATION_FES, EQOS_MAC_CONFIGURATION_PS);
+
+       return 0;
+}
+
+static int eqos_set_tx_clk_speed_tegra186(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       ulong rate;
+       int ret;
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       switch (eqos->phy->speed) {
+       case SPEED_1000:
+               rate = 125 * 1000 * 1000;
+               break;
+       case SPEED_100:
+               rate = 25 * 1000 * 1000;
+               break;
+       case SPEED_10:
+               rate = 2.5 * 1000 * 1000;
+               break;
+       default:
+               error("invalid speed %d", eqos->phy->speed);
+               return -EINVAL;
+       }
+
+       ret = clk_set_rate(&eqos->clk_tx, rate);
+       if (ret < 0) {
+               error("clk_set_rate(tx_clk, %lu) failed: %d", rate, ret);
+               return ret;
+       }
+
+       return 0;
+}
+
+static int eqos_adjust_link(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       int ret;
+       bool en_calibration;
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       if (eqos->phy->duplex)
+               ret = eqos_set_full_duplex(dev);
+       else
+               ret = eqos_set_half_duplex(dev);
+       if (ret < 0) {
+               error("eqos_set_*_duplex() failed: %d", ret);
+               return ret;
+       }
+
+       switch (eqos->phy->speed) {
+       case SPEED_1000:
+               en_calibration = true;
+               ret = eqos_set_gmii_speed(dev);
+               break;
+       case SPEED_100:
+               en_calibration = true;
+               ret = eqos_set_mii_speed_100(dev);
+               break;
+       case SPEED_10:
+               en_calibration = false;
+               ret = eqos_set_mii_speed_10(dev);
+               break;
+       default:
+               error("invalid speed %d", eqos->phy->speed);
+               return -EINVAL;
+       }
+       if (ret < 0) {
+               error("eqos_set_*mii_speed*() failed: %d", ret);
+               return ret;
+       }
+
+       if (en_calibration) {
+               ret = eqos_calibrate_pads_tegra186(dev);
+               if (ret < 0) {
+                       error("eqos_calibrate_pads_tegra186() failed: %d", ret);
+                       return ret;
+               }
+       } else {
+               ret = eqos_disable_calibration_tegra186(dev);
+               if (ret < 0) {
+                       error("eqos_disable_calibration_tegra186() failed: %d",
+                             ret);
+                       return ret;
+               }
+       }
+
+       ret = eqos_set_tx_clk_speed_tegra186(dev);
+       if (ret < 0) {
+               error("eqos_set_tx_clk_speed_tegra186() failed: %d", ret);
+               return ret;
+       }
+
+       return 0;
+}
+
+static int eqos_write_hwaddr(struct udevice *dev)
+{
+       struct eth_pdata *plat = dev_get_platdata(dev);
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       uint32_t val;
+
+       /*
+        * This function may be called before start() or after stop(). At that
+        * time, on at least some configurations of the EQoS HW, all clocks to
+        * the EQoS HW block will be stopped, and a reset signal applied. If
+        * any register access is attempted in this state, bus timeouts or CPU
+        * hangs may occur. This check prevents that.
+        *
+        * A simple solution to this problem would be to not implement
+        * write_hwaddr(), since start() always writes the MAC address into HW
+        * anyway. However, it is desirable to implement write_hwaddr() to
+        * support the case of SW that runs subsequent to U-Boot which expects
+        * the MAC address to already be programmed into the EQoS registers,
+        * which must happen irrespective of whether the U-Boot user (or
+        * scripts) actually made use of the EQoS device, and hence
+        * irrespective of whether start() was ever called.
+        *
+        * Note that this requirement by subsequent SW is not valid for
+        * Tegra186, and is likely not valid for any non-PCI instantiation of
+        * the EQoS HW block. This function is implemented solely as
+        * future-proofing with the expectation the driver will eventually be
+        * ported to some system where the expectation above is true.
+        */
+       if (!eqos->config->reg_access_always_ok && !eqos->reg_access_ok)
+               return 0;
+
+       /* Update the MAC address */
+       val = (plat->enetaddr[5] << 8) |
+               (plat->enetaddr[4]);
+       writel(val, &eqos->mac_regs->address0_high);
+       val = (plat->enetaddr[3] << 24) |
+               (plat->enetaddr[2] << 16) |
+               (plat->enetaddr[1] << 8) |
+               (plat->enetaddr[0]);
+       writel(val, &eqos->mac_regs->address0_low);
+
+       return 0;
+}
+
+static int eqos_start(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       int ret, i;
+       ulong rate;
+       u32 val, tx_fifo_sz, rx_fifo_sz, tqs, rqs, pbl;
+       ulong last_rx_desc;
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       eqos->tx_desc_idx = 0;
+       eqos->rx_desc_idx = 0;
+
+       ret = eqos_start_clks_tegra186(dev);
+       if (ret < 0) {
+               error("eqos_start_clks_tegra186() failed: %d", ret);
+               goto err;
+       }
+
+       ret = eqos_start_resets_tegra186(dev);
+       if (ret < 0) {
+               error("eqos_start_resets_tegra186() failed: %d", ret);
+               goto err_stop_clks;
+       }
+
+       udelay(10);
+
+       eqos->reg_access_ok = true;
+
+       ret = wait_for_bit(__func__, &eqos->dma_regs->mode,
+                          EQOS_DMA_MODE_SWR, false, 10, false);
+       if (ret) {
+               error("EQOS_DMA_MODE_SWR stuck");
+               goto err_stop_resets;
+       }
+
+       ret = eqos_calibrate_pads_tegra186(dev);
+       if (ret < 0) {
+               error("eqos_calibrate_pads_tegra186() failed: %d", ret);
+               goto err_stop_resets;
+       }
+
+       rate = eqos_get_tick_clk_rate_tegra186(dev);
+       val = (rate / 1000000) - 1;
+       writel(val, &eqos->mac_regs->us_tic_counter);
+
+       eqos->phy = phy_connect(eqos->mii, 0, dev, 0);
+       if (!eqos->phy) {
+               error("phy_connect() failed");
+               goto err_stop_resets;
+       }
+       ret = phy_config(eqos->phy);
+       if (ret < 0) {
+               error("phy_config() failed: %d", ret);
+               goto err_shutdown_phy;
+       }
+       ret = phy_startup(eqos->phy);
+       if (ret < 0) {
+               error("phy_startup() failed: %d", ret);
+               goto err_shutdown_phy;
+       }
+
+       if (!eqos->phy->link) {
+               error("No link");
+               goto err_shutdown_phy;
+       }
+
+       ret = eqos_adjust_link(dev);
+       if (ret < 0) {
+               error("eqos_adjust_link() failed: %d", ret);
+               goto err_shutdown_phy;
+       }
+
+       /* Configure MTL */
+
+       /* Enable Store and Forward mode for TX */
+       /* Program Tx operating mode */
+       setbits_le32(&eqos->mtl_regs->txq0_operation_mode,
+                    EQOS_MTL_TXQ0_OPERATION_MODE_TSF |
+                    (EQOS_MTL_TXQ0_OPERATION_MODE_TXQEN_ENABLED <<
+                     EQOS_MTL_TXQ0_OPERATION_MODE_TXQEN_SHIFT));
+
+       /* Transmit Queue weight */
+       writel(0x10, &eqos->mtl_regs->txq0_quantum_weight);
+
+       /* Enable Store and Forward mode for RX, since no jumbo frame */
+       setbits_le32(&eqos->mtl_regs->rxq0_operation_mode,
+                    EQOS_MTL_RXQ0_OPERATION_MODE_RSF);
+
+       /* Transmit/Receive queue fifo size; use all RAM for 1 queue */
+       val = readl(&eqos->mac_regs->hw_feature1);
+       tx_fifo_sz = (val >> EQOS_MAC_HW_FEATURE1_TXFIFOSIZE_SHIFT) &
+               EQOS_MAC_HW_FEATURE1_TXFIFOSIZE_MASK;
+       rx_fifo_sz = (val >> EQOS_MAC_HW_FEATURE1_RXFIFOSIZE_SHIFT) &
+               EQOS_MAC_HW_FEATURE1_RXFIFOSIZE_MASK;
+
+       /*
+        * r/tx_fifo_sz is encoded as log2(n / 128). Undo that by shifting.
+        * r/tqs is encoded as (n / 256) - 1.
+        */
+       tqs = (128 << tx_fifo_sz) / 256 - 1;
+       rqs = (128 << rx_fifo_sz) / 256 - 1;
+
+       clrsetbits_le32(&eqos->mtl_regs->txq0_operation_mode,
+                       EQOS_MTL_TXQ0_OPERATION_MODE_TQS_MASK <<
+                       EQOS_MTL_TXQ0_OPERATION_MODE_TQS_SHIFT,
+                       tqs << EQOS_MTL_TXQ0_OPERATION_MODE_TQS_SHIFT);
+       clrsetbits_le32(&eqos->mtl_regs->rxq0_operation_mode,
+                       EQOS_MTL_RXQ0_OPERATION_MODE_RQS_MASK <<
+                       EQOS_MTL_RXQ0_OPERATION_MODE_RQS_SHIFT,
+                       rqs << EQOS_MTL_RXQ0_OPERATION_MODE_RQS_SHIFT);
+
+       /* Flow control used only if each channel gets 4KB or more FIFO */
+       if (rqs >= ((4096 / 256) - 1)) {
+               u32 rfd, rfa;
+
+               setbits_le32(&eqos->mtl_regs->rxq0_operation_mode,
+                            EQOS_MTL_RXQ0_OPERATION_MODE_EHFC);
+
+               /*
+                * Set Threshold for Activating Flow Contol space for min 2
+                * frames ie, (1500 * 1) = 1500 bytes.
+                *
+                * Set Threshold for Deactivating Flow Contol for space of
+                * min 1 frame (frame size 1500bytes) in receive fifo
+                */
+               if (rqs == ((4096 / 256) - 1)) {
+                       /*
+                        * This violates the above formula because of FIFO size
+                        * limit therefore overflow may occur inspite of this.
+                        */
+                       rfd = 0x3;      /* Full-3K */
+                       rfa = 0x1;      /* Full-1.5K */
+               } else if (rqs == ((8192 / 256) - 1)) {
+                       rfd = 0x6;      /* Full-4K */
+                       rfa = 0xa;      /* Full-6K */
+               } else if (rqs == ((16384 / 256) - 1)) {
+                       rfd = 0x6;      /* Full-4K */
+                       rfa = 0x12;     /* Full-10K */
+               } else {
+                       rfd = 0x6;      /* Full-4K */
+                       rfa = 0x1E;     /* Full-16K */
+               }
+
+               clrsetbits_le32(&eqos->mtl_regs->rxq0_operation_mode,
+                               (EQOS_MTL_RXQ0_OPERATION_MODE_RFD_MASK <<
+                                EQOS_MTL_RXQ0_OPERATION_MODE_RFD_SHIFT) |
+                               (EQOS_MTL_RXQ0_OPERATION_MODE_RFA_MASK <<
+                                EQOS_MTL_RXQ0_OPERATION_MODE_RFA_SHIFT),
+                               (rfd <<
+                                EQOS_MTL_RXQ0_OPERATION_MODE_RFD_SHIFT) |
+                               (rfa <<
+                                EQOS_MTL_RXQ0_OPERATION_MODE_RFA_SHIFT));
+       }
+
+       /* Configure MAC */
+
+       clrsetbits_le32(&eqos->mac_regs->rxq_ctrl0,
+                       EQOS_MAC_RXQ_CTRL0_RXQ0EN_MASK <<
+                       EQOS_MAC_RXQ_CTRL0_RXQ0EN_SHIFT,
+                       EQOS_MAC_RXQ_CTRL0_RXQ0EN_ENABLED_DCB <<
+                       EQOS_MAC_RXQ_CTRL0_RXQ0EN_SHIFT);
+
+       /* Set TX flow control parameters */
+       /* Set Pause Time */
+       setbits_le32(&eqos->mac_regs->q0_tx_flow_ctrl,
+                    0xffff << EQOS_MAC_Q0_TX_FLOW_CTRL_PT_SHIFT);
+       /* Assign priority for TX flow control */
+       clrbits_le32(&eqos->mac_regs->txq_prty_map0,
+                    EQOS_MAC_TXQ_PRTY_MAP0_PSTQ0_MASK <<
+                    EQOS_MAC_TXQ_PRTY_MAP0_PSTQ0_SHIFT);
+       /* Assign priority for RX flow control */
+       clrbits_le32(&eqos->mac_regs->rxq_ctrl2,
+                    EQOS_MAC_RXQ_CTRL2_PSRQ0_MASK <<
+                    EQOS_MAC_RXQ_CTRL2_PSRQ0_SHIFT);
+       /* Enable flow control */
+       setbits_le32(&eqos->mac_regs->q0_tx_flow_ctrl,
+                    EQOS_MAC_Q0_TX_FLOW_CTRL_TFE);
+       setbits_le32(&eqos->mac_regs->rx_flow_ctrl,
+                    EQOS_MAC_RX_FLOW_CTRL_RFE);
+
+       clrsetbits_le32(&eqos->mac_regs->configuration,
+                       EQOS_MAC_CONFIGURATION_GPSLCE |
+                       EQOS_MAC_CONFIGURATION_WD |
+                       EQOS_MAC_CONFIGURATION_JD |
+                       EQOS_MAC_CONFIGURATION_JE,
+                       EQOS_MAC_CONFIGURATION_CST |
+                       EQOS_MAC_CONFIGURATION_ACS);
+
+       eqos_write_hwaddr(dev);
+
+       /* Configure DMA */
+
+       /* Enable OSP mode */
+       setbits_le32(&eqos->dma_regs->ch0_tx_control,
+                    EQOS_DMA_CH0_TX_CONTROL_OSP);
+
+       /* RX buffer size. Must be a multiple of bus width */
+       clrsetbits_le32(&eqos->dma_regs->ch0_rx_control,
+                       EQOS_DMA_CH0_RX_CONTROL_RBSZ_MASK <<
+                       EQOS_DMA_CH0_RX_CONTROL_RBSZ_SHIFT,
+                       EQOS_MAX_PACKET_SIZE <<
+                       EQOS_DMA_CH0_RX_CONTROL_RBSZ_SHIFT);
+
+       setbits_le32(&eqos->dma_regs->ch0_control,
+                    EQOS_DMA_CH0_CONTROL_PBLX8);
+
+       /*
+        * Burst length must be < 1/2 FIFO size.
+        * FIFO size in tqs is encoded as (n / 256) - 1.
+        * Each burst is n * 8 (PBLX8) * 16 (AXI width) == 128 bytes.
+        * Half of n * 256 is n * 128, so pbl == tqs, modulo the -1.
+        */
+       pbl = tqs + 1;
+       if (pbl > 32)
+               pbl = 32;
+       clrsetbits_le32(&eqos->dma_regs->ch0_tx_control,
+                       EQOS_DMA_CH0_TX_CONTROL_TXPBL_MASK <<
+                       EQOS_DMA_CH0_TX_CONTROL_TXPBL_SHIFT,
+                       pbl << EQOS_DMA_CH0_TX_CONTROL_TXPBL_SHIFT);
+
+       clrsetbits_le32(&eqos->dma_regs->ch0_rx_control,
+                       EQOS_DMA_CH0_RX_CONTROL_RXPBL_MASK <<
+                       EQOS_DMA_CH0_RX_CONTROL_RXPBL_SHIFT,
+                       8 << EQOS_DMA_CH0_RX_CONTROL_RXPBL_SHIFT);
+
+       /* DMA performance configuration */
+       val = (2 << EQOS_DMA_SYSBUS_MODE_RD_OSR_LMT_SHIFT) |
+               EQOS_DMA_SYSBUS_MODE_EAME | EQOS_DMA_SYSBUS_MODE_BLEN16 |
+               EQOS_DMA_SYSBUS_MODE_BLEN8 | EQOS_DMA_SYSBUS_MODE_BLEN4;
+       writel(val, &eqos->dma_regs->sysbus_mode);
+
+       /* Set up descriptors */
+
+       memset(eqos->descs, 0, EQOS_DESCRIPTORS_SIZE);
+       for (i = 0; i < EQOS_DESCRIPTORS_RX; i++) {
+               struct eqos_desc *rx_desc = &(eqos->rx_descs[i]);
+               rx_desc->des0 = (u32)(ulong)(eqos->rx_dma_buf +
+                                            (i * EQOS_MAX_PACKET_SIZE));
+               rx_desc->des3 |= EQOS_DESC3_OWN | EQOS_DESC3_BUF1V;
+       }
+       flush_cache((unsigned long)eqos->descs, EQOS_DESCRIPTORS_SIZE);
+
+       writel(0, &eqos->dma_regs->ch0_txdesc_list_haddress);
+       writel((ulong)eqos->tx_descs, &eqos->dma_regs->ch0_txdesc_list_address);
+       writel(EQOS_DESCRIPTORS_TX - 1,
+              &eqos->dma_regs->ch0_txdesc_ring_length);
+
+       writel(0, &eqos->dma_regs->ch0_rxdesc_list_haddress);
+       writel((ulong)eqos->rx_descs, &eqos->dma_regs->ch0_rxdesc_list_address);
+       writel(EQOS_DESCRIPTORS_RX - 1,
+              &eqos->dma_regs->ch0_rxdesc_ring_length);
+
+       /* Enable everything */
+
+       setbits_le32(&eqos->mac_regs->configuration,
+                    EQOS_MAC_CONFIGURATION_TE | EQOS_MAC_CONFIGURATION_RE);
+
+       setbits_le32(&eqos->dma_regs->ch0_tx_control,
+                    EQOS_DMA_CH0_TX_CONTROL_ST);
+       setbits_le32(&eqos->dma_regs->ch0_rx_control,
+                    EQOS_DMA_CH0_RX_CONTROL_SR);
+
+       /* TX tail pointer not written until we need to TX a packet */
+       /*
+        * Point RX tail pointer at last descriptor. Ideally, we'd point at the
+        * first descriptor, implying all descriptors were available. However,
+        * that's not distinguishable from none of the descriptors being
+        * available.
+        */
+       last_rx_desc = (ulong)&(eqos->rx_descs[(EQOS_DESCRIPTORS_RX - 1)]);
+       writel(last_rx_desc, &eqos->dma_regs->ch0_rxdesc_tail_pointer);
+
+       eqos->started = true;
+
+       debug("%s: OK\n", __func__);
+       return 0;
+
+err_shutdown_phy:
+       phy_shutdown(eqos->phy);
+       eqos->phy = NULL;
+err_stop_resets:
+       eqos_stop_resets_tegra186(dev);
+err_stop_clks:
+       eqos_stop_clks_tegra186(dev);
+err:
+       error("FAILED: %d", ret);
+       return ret;
+}
+
+void eqos_stop(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       int i;
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       if (!eqos->started)
+               return;
+       eqos->started = false;
+       eqos->reg_access_ok = false;
+
+       /* Disable TX DMA */
+       clrbits_le32(&eqos->dma_regs->ch0_tx_control,
+                    EQOS_DMA_CH0_TX_CONTROL_ST);
+
+       /* Wait for TX all packets to drain out of MTL */
+       for (i = 0; i < 1000000; i++) {
+               u32 val = readl(&eqos->mtl_regs->txq0_debug);
+               u32 trcsts = (val >> EQOS_MTL_TXQ0_DEBUG_TRCSTS_SHIFT) &
+                       EQOS_MTL_TXQ0_DEBUG_TRCSTS_MASK;
+               u32 txqsts = val & EQOS_MTL_TXQ0_DEBUG_TXQSTS;
+               if ((trcsts != 1) && (!txqsts))
+                       break;
+       }
+
+       /* Turn off MAC TX and RX */
+       clrbits_le32(&eqos->mac_regs->configuration,
+                    EQOS_MAC_CONFIGURATION_TE | EQOS_MAC_CONFIGURATION_RE);
+
+       /* Wait for all RX packets to drain out of MTL */
+       for (i = 0; i < 1000000; i++) {
+               u32 val = readl(&eqos->mtl_regs->rxq0_debug);
+               u32 prxq = (val >> EQOS_MTL_RXQ0_DEBUG_PRXQ_SHIFT) &
+                       EQOS_MTL_RXQ0_DEBUG_PRXQ_MASK;
+               u32 rxqsts = (val >> EQOS_MTL_RXQ0_DEBUG_RXQSTS_SHIFT) &
+                       EQOS_MTL_RXQ0_DEBUG_RXQSTS_MASK;
+               if ((!prxq) && (!rxqsts))
+                       break;
+       }
+
+       /* Turn off RX DMA */
+       clrbits_le32(&eqos->dma_regs->ch0_rx_control,
+                    EQOS_DMA_CH0_RX_CONTROL_SR);
+
+       if (eqos->phy) {
+               phy_shutdown(eqos->phy);
+               eqos->phy = NULL;
+       }
+       eqos_stop_resets_tegra186(dev);
+       eqos_stop_clks_tegra186(dev);
+
+       debug("%s: OK\n", __func__);
+}
+
+int eqos_send(struct udevice *dev, void *packet, int length)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       struct eqos_desc *tx_desc;
+       int i;
+
+       debug("%s(dev=%p, packet=%p, length=%d):\n", __func__, dev, packet,
+             length);
+
+       memcpy(eqos->tx_dma_buf, packet, length);
+       eqos_flush_buffer(eqos->tx_dma_buf, length);
+
+       tx_desc = &(eqos->tx_descs[eqos->tx_desc_idx]);
+       eqos->tx_desc_idx++;
+       eqos->tx_desc_idx %= EQOS_DESCRIPTORS_TX;
+
+       tx_desc->des0 = (ulong)eqos->tx_dma_buf;
+       tx_desc->des1 = 0;
+       tx_desc->des2 = length;
+       /*
+        * Make sure that if HW sees the _OWN write below, it will see all the
+        * writes to the rest of the descriptor too.
+        */
+       mb();
+       tx_desc->des3 = EQOS_DESC3_OWN | EQOS_DESC3_FD | EQOS_DESC3_LD | length;
+       eqos_flush_desc(tx_desc);
+
+       writel((ulong)(tx_desc + 1), &eqos->dma_regs->ch0_txdesc_tail_pointer);
+
+       for (i = 0; i < 1000000; i++) {
+               eqos_inval_desc(tx_desc);
+               if (!(readl(&tx_desc->des3) & EQOS_DESC3_OWN))
+                       return 0;
+               udelay(1);
+       }
+
+       debug("%s: TX timeout\n", __func__);
+
+       return -ETIMEDOUT;
+}
+
+int eqos_recv(struct udevice *dev, int flags, uchar **packetp)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       struct eqos_desc *rx_desc;
+       int length;
+
+       debug("%s(dev=%p, flags=%x):\n", __func__, dev, flags);
+
+       rx_desc = &(eqos->rx_descs[eqos->rx_desc_idx]);
+       if (rx_desc->des3 & EQOS_DESC3_OWN) {
+               debug("%s: RX packet not available\n", __func__);
+               return -EAGAIN;
+       }
+
+       *packetp = eqos->rx_dma_buf +
+               (eqos->rx_desc_idx * EQOS_MAX_PACKET_SIZE);
+       length = rx_desc->des3 & 0x7fff;
+       debug("%s: *packetp=%p, length=%d\n", __func__, *packetp, length);
+
+       eqos_inval_buffer(*packetp, length);
+
+       return length;
+}
+
+int eqos_free_pkt(struct udevice *dev, uchar *packet, int length)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       uchar *packet_expected;
+       struct eqos_desc *rx_desc;
+
+       debug("%s(packet=%p, length=%d)\n", __func__, packet, length);
+
+       packet_expected = eqos->rx_dma_buf +
+               (eqos->rx_desc_idx * EQOS_MAX_PACKET_SIZE);
+       if (packet != packet_expected) {
+               debug("%s: Unexpected packet (expected %p)\n", __func__,
+                     packet_expected);
+               return -EINVAL;
+       }
+
+       rx_desc = &(eqos->rx_descs[eqos->rx_desc_idx]);
+       rx_desc->des0 = (u32)(ulong)packet;
+       rx_desc->des1 = 0;
+       rx_desc->des2 = 0;
+       /*
+        * Make sure that if HW sees the _OWN write below, it will see all the
+        * writes to the rest of the descriptor too.
+        */
+       mb();
+       rx_desc->des3 |= EQOS_DESC3_OWN | EQOS_DESC3_BUF1V;
+       eqos_flush_desc(rx_desc);
+
+       writel((ulong)rx_desc, &eqos->dma_regs->ch0_rxdesc_tail_pointer);
+
+       eqos->rx_desc_idx++;
+       eqos->rx_desc_idx %= EQOS_DESCRIPTORS_RX;
+
+       return 0;
+}
+
+static int eqos_probe_resources_core(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       int ret;
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       eqos->descs = eqos_alloc_descs(EQOS_DESCRIPTORS_TX +
+                                      EQOS_DESCRIPTORS_RX);
+       if (!eqos->descs) {
+               debug("%s: eqos_alloc_descs() failed\n", __func__);
+               ret = -ENOMEM;
+               goto err;
+       }
+       eqos->tx_descs = (struct eqos_desc *)eqos->descs;
+       eqos->rx_descs = (eqos->tx_descs + EQOS_DESCRIPTORS_TX);
+       debug("%s: tx_descs=%p, rx_descs=%p\n", __func__, eqos->tx_descs,
+             eqos->rx_descs);
+
+       eqos->tx_dma_buf = memalign(EQOS_BUFFER_ALIGN, EQOS_MAX_PACKET_SIZE);
+       if (!eqos->tx_dma_buf) {
+               debug("%s: memalign(tx_dma_buf) failed\n", __func__);
+               ret = -ENOMEM;
+               goto err_free_descs;
+       }
+       debug("%s: rx_dma_buf=%p\n", __func__, eqos->rx_dma_buf);
+
+       eqos->rx_dma_buf = memalign(EQOS_BUFFER_ALIGN, EQOS_RX_BUFFER_SIZE);
+       if (!eqos->rx_dma_buf) {
+               debug("%s: memalign(rx_dma_buf) failed\n", __func__);
+               ret = -ENOMEM;
+               goto err_free_tx_dma_buf;
+       }
+       debug("%s: tx_dma_buf=%p\n", __func__, eqos->tx_dma_buf);
+
+       eqos->rx_pkt = malloc(EQOS_MAX_PACKET_SIZE);
+       if (!eqos->rx_pkt) {
+               debug("%s: malloc(rx_pkt) failed\n", __func__);
+               ret = -ENOMEM;
+               goto err_free_rx_dma_buf;
+       }
+       debug("%s: rx_pkt=%p\n", __func__, eqos->rx_pkt);
+
+       debug("%s: OK\n", __func__);
+       return 0;
+
+err_free_rx_dma_buf:
+       free(eqos->rx_dma_buf);
+err_free_tx_dma_buf:
+       free(eqos->tx_dma_buf);
+err_free_descs:
+       eqos_free_descs(eqos->descs);
+err:
+
+       debug("%s: returns %d\n", __func__, ret);
+       return ret;
+}
+
+static int eqos_remove_resources_core(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       free(eqos->rx_pkt);
+       free(eqos->rx_dma_buf);
+       free(eqos->tx_dma_buf);
+       eqos_free_descs(eqos->descs);
+
+       debug("%s: OK\n", __func__);
+       return 0;
+}
+
+static int eqos_probe_resources_tegra186(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       int ret;
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       ret = reset_get_by_name(dev, "eqos", &eqos->reset_ctl);
+       if (ret) {
+               error("reset_get_by_name(rst) failed: %d", ret);
+               return ret;
+       }
+
+       ret = gpio_request_by_name(dev, "phy-reset-gpios", 0,
+                                  &eqos->phy_reset_gpio,
+                                  GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
+       if (ret) {
+               error("gpio_request_by_name(phy reset) failed: %d", ret);
+               goto err_free_reset_eqos;
+       }
+
+       ret = clk_get_by_name(dev, "slave_bus", &eqos->clk_slave_bus);
+       if (ret) {
+               error("clk_get_by_name(slave_bus) failed: %d", ret);
+               goto err_free_gpio_phy_reset;
+       }
+
+       ret = clk_get_by_name(dev, "master_bus", &eqos->clk_master_bus);
+       if (ret) {
+               error("clk_get_by_name(master_bus) failed: %d", ret);
+               goto err_free_clk_slave_bus;
+       }
+
+       ret = clk_get_by_name(dev, "rx", &eqos->clk_rx);
+       if (ret) {
+               error("clk_get_by_name(rx) failed: %d", ret);
+               goto err_free_clk_master_bus;
+       }
+
+       ret = clk_get_by_name(dev, "ptp_ref", &eqos->clk_ptp_ref);
+       if (ret) {
+               error("clk_get_by_name(ptp_ref) failed: %d", ret);
+               goto err_free_clk_rx;
+               return ret;
+       }
+
+       ret = clk_get_by_name(dev, "tx", &eqos->clk_tx);
+       if (ret) {
+               error("clk_get_by_name(tx) failed: %d", ret);
+               goto err_free_clk_ptp_ref;
+       }
+
+       debug("%s: OK\n", __func__);
+       return 0;
+
+err_free_clk_ptp_ref:
+       clk_free(&eqos->clk_ptp_ref);
+err_free_clk_rx:
+       clk_free(&eqos->clk_rx);
+err_free_clk_master_bus:
+       clk_free(&eqos->clk_master_bus);
+err_free_clk_slave_bus:
+       clk_free(&eqos->clk_slave_bus);
+err_free_gpio_phy_reset:
+       dm_gpio_free(dev, &eqos->phy_reset_gpio);
+err_free_reset_eqos:
+       reset_free(&eqos->reset_ctl);
+
+       debug("%s: returns %d\n", __func__, ret);
+       return ret;
+}
+
+static int eqos_remove_resources_tegra186(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       clk_free(&eqos->clk_tx);
+       clk_free(&eqos->clk_ptp_ref);
+       clk_free(&eqos->clk_rx);
+       clk_free(&eqos->clk_slave_bus);
+       clk_free(&eqos->clk_master_bus);
+       dm_gpio_free(dev, &eqos->phy_reset_gpio);
+       reset_free(&eqos->reset_ctl);
+
+       debug("%s: OK\n", __func__);
+       return 0;
+}
+
+static int eqos_probe(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       int ret;
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       eqos->dev = dev;
+       eqos->config = (void *)dev_get_driver_data(dev);
+
+       eqos->regs = dev_get_addr(dev);
+       if (eqos->regs == FDT_ADDR_T_NONE) {
+               error("dev_get_addr() failed");
+               return -ENODEV;
+       }
+       eqos->mac_regs = (void *)(eqos->regs + EQOS_MAC_REGS_BASE);
+       eqos->mtl_regs = (void *)(eqos->regs + EQOS_MTL_REGS_BASE);
+       eqos->dma_regs = (void *)(eqos->regs + EQOS_DMA_REGS_BASE);
+       eqos->tegra186_regs = (void *)(eqos->regs + EQOS_TEGRA186_REGS_BASE);
+
+       ret = eqos_probe_resources_core(dev);
+       if (ret < 0) {
+               error("eqos_probe_resources_core() failed: %d", ret);
+               return ret;
+       }
+
+       ret = eqos_probe_resources_tegra186(dev);
+       if (ret < 0) {
+               error("eqos_probe_resources_tegra186() failed: %d", ret);
+               goto err_remove_resources_core;
+       }
+
+       eqos->mii = mdio_alloc();
+       if (!eqos->mii) {
+               error("mdio_alloc() failed");
+               goto err_remove_resources_tegra;
+       }
+       eqos->mii->read = eqos_mdio_read;
+       eqos->mii->write = eqos_mdio_write;
+       eqos->mii->priv = eqos;
+       strcpy(eqos->mii->name, dev->name);
+
+       ret = mdio_register(eqos->mii);
+       if (ret < 0) {
+               error("mdio_register() failed: %d", ret);
+               goto err_free_mdio;
+       }
+
+       debug("%s: OK\n", __func__);
+       return 0;
+
+err_free_mdio:
+       mdio_free(eqos->mii);
+err_remove_resources_tegra:
+       eqos_remove_resources_tegra186(dev);
+err_remove_resources_core:
+       eqos_remove_resources_core(dev);
+
+       debug("%s: returns %d\n", __func__, ret);
+       return ret;
+}
+
+static int eqos_remove(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       mdio_unregister(eqos->mii);
+       mdio_free(eqos->mii);
+       eqos_remove_resources_tegra186(dev);
+       eqos_probe_resources_core(dev);
+
+       debug("%s: OK\n", __func__);
+       return 0;
+}
+
+static const struct eth_ops eqos_ops = {
+       .start = eqos_start,
+       .stop = eqos_stop,
+       .send = eqos_send,
+       .recv = eqos_recv,
+       .free_pkt = eqos_free_pkt,
+       .write_hwaddr = eqos_write_hwaddr,
+};
+
+static const struct eqos_config eqos_tegra186_config = {
+       .reg_access_always_ok = false,
+};
+
+static const struct udevice_id eqos_ids[] = {
+       {
+               .compatible = "nvidia,tegra186-eqos",
+               .data = (ulong)&eqos_tegra186_config
+       },
+       { }
+};
+
+U_BOOT_DRIVER(eth_eqos) = {
+       .name = "eth_eqos",
+       .id = UCLASS_ETH,
+       .of_match = eqos_ids,
+       .probe = eqos_probe,
+       .remove = eqos_remove,
+       .ops = &eqos_ops,
+       .priv_auto_alloc_size = sizeof(struct eqos_priv),
+       .platdata_auto_alloc_size = sizeof(struct eth_pdata),
+};
index c784cdcae2653fe2966b2bd9477759017c8e10ac..f833efbe67791b3234f1230300b92914f50ed9a8 100644 (file)
@@ -177,25 +177,6 @@ static int smi_reg_write(struct mii_dev *bus, int phy_adr, int devad,
 }
 #endif
 
-#if defined(CONFIG_PHYLIB)
-int mvgbe_phy_read(struct mii_dev *bus, int phy_addr, int dev_addr,
-                  int reg_addr)
-{
-       u16 data;
-       int ret;
-       ret = smi_reg_read(bus->name, phy_addr, reg_addr, &data);
-       if (ret)
-               return ret;
-       return data;
-}
-
-int mvgbe_phy_write(struct mii_dev *bus, int phy_addr, int dev_addr,
-                   int reg_addr, u16 data)
-{
-       return smi_reg_write(bus->name, phy_addr, reg_addr, data);
-}
-#endif
-
 /* Stop and checks all queues */
 static void stop_queue(u32 * qreg)
 {
@@ -676,8 +657,8 @@ int mvgbe_phylib_init(struct eth_device *dev, int phyid)
                printf("mdio_alloc failed\n");
                return -ENOMEM;
        }
-       bus->read = mvgbe_phy_read;
-       bus->write = mvgbe_phy_write;
+       bus->read = smi_reg_read;
+       bus->write = smi_reg_write;
        strcpy(bus->name, dev->name);
 
        ret = mdio_register(bus);
@@ -688,7 +669,7 @@ int mvgbe_phylib_init(struct eth_device *dev, int phyid)
        }
 
        /* Set phy address of the port */
-       mvgbe_phy_write(bus, MV_PHY_ADR_REQUEST, 0, MV_PHY_ADR_REQUEST, phyid);
+       smi_reg_write(bus, MV_PHY_ADR_REQUEST, 0, MV_PHY_ADR_REQUEST, phyid);
 
        phydev = phy_connect(bus, phyid, dev, PHY_INTERFACE_MODE_RGMII);
        if (!phydev) {
index 6b313a9fd3244662ae8218b12276d970341ae98b..28a14018835b175469233385af7546e0ac3ceddd 100644 (file)
@@ -415,11 +415,31 @@ static int ksz9031_of_config(struct phy_device *phydev)
 
        return 0;
 }
+
+static int ksz9031_center_flp_timing(struct phy_device *phydev)
+{
+       struct phy_driver *drv = phydev->drv;
+       int ret = 0;
+
+       if (!drv || !drv->writeext)
+               return -EOPNOTSUPP;
+
+       ret = drv->writeext(phydev, 0, 0, MII_KSZ9031_FLP_BURST_TX_LO, 0x1A80);
+       if (ret)
+               return ret;
+
+       ret = drv->writeext(phydev, 0, 0, MII_KSZ9031_FLP_BURST_TX_HI, 0x6);
+       return ret;
+}
 #else
 static int ksz9031_of_config(struct phy_device *phydev)
 {
        return 0;
 }
+static int ksz9031_center_flp_timing(struct phy_device *phydev)
+{
+       return 0;
+}
 #endif
 
 /* Accessors to extended registers*/
@@ -470,6 +490,9 @@ static int ksz9031_config(struct phy_device *phydev)
 {
        int ret;
        ret = ksz9031_of_config(phydev);
+       if (ret)
+               return ret;
+       ret = ksz9031_center_flp_timing(phydev);
        if (ret)
                return ret;
        return genphy_config(phydev);
index e6d145d4b25eb5424339e4b5c4a1ae432ff7516f..3e6b5312d85a2f8f7edc488dbb54dbc76368d708 100644 (file)
@@ -20,6 +20,9 @@
 #define MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW     0x6
 #define MII_KSZ9031_EXT_RGMII_CLOCK_SKEW       0x8
 
+#define MII_KSZ9031_FLP_BURST_TX_LO            0x3
+#define MII_KSZ9031_FLP_BURST_TX_HI            0x4
+
 /* Registers */
 #define MMD_ACCESS_CONTROL     0xd
 #define MMD_ACCESS_REG_DATA    0xe
index a32961e6ceaae8e819a247c1f30bac24b3bc370f..1d130110890ec402048fea58eb1a52461e9899a0 100644 (file)
@@ -512,7 +512,8 @@ static int eth_post_probe(struct udevice *dev)
                eth_setenv_enetaddr_by_index("eth", dev->seq, pdata->enetaddr);
                printf("\nWarning: %s using MAC address from ROM\n",
                       dev->name);
-       } else if (is_zero_ethaddr(pdata->enetaddr)) {
+       } else if (is_zero_ethaddr(pdata->enetaddr) ||
+                  !is_valid_ethaddr(pdata->enetaddr)) {
 #ifdef CONFIG_NET_RANDOM_ETHADDR
                net_random_ethaddr(pdata->enetaddr);
                printf("\nWarning: %s (eth%d) using random MAC address - %pM\n",