select CPU_V7A
select ROM_UNIFIED_SECTIONS
imply MXC_GPIO
+ imply SYS_THUMB_BUILD
config ARCH_MX7
bool "Freescale MX7"
select SYS_FSL_SEC_COMPAT_4
select SYS_FSL_SEC_LE
imply MXC_GPIO
+ imply SYS_THUMB_BUILD
config ARCH_MX6
bool "Freescale MX6"
select SYS_FSL_HAS_SEC if IMX_HAB
select SYS_FSL_SEC_COMPAT_4
select SYS_FSL_SEC_LE
- select SYS_THUMB_BUILD if SPL
imply MXC_GPIO
+ imply SYS_THUMB_BUILD
if ARCH_MX6
config SPL_LDSCRIPT
/*
* Enable NAND clock
*/
- /* Clear bypass bit */
+ /* Set bypass bit */
writel(CLKCTRL_CLKSEQ_BYPASS_GPMI,
&clkctrl_regs->hw_clkctrl_clkseq_set);
- /* Set GPMI clock to ref_gpmi / 12 */
+ /* Set GPMI clock to ref_xtal / 1 */
+ clrbits_le32(&clkctrl_regs->hw_clkctrl_gpmi, CLKCTRL_GPMI_CLKGATE);
+ while (readl(&clkctrl_regs->hw_clkctrl_gpmi) & CLKCTRL_GPMI_CLKGATE)
+ ;
clrsetbits_le32(&clkctrl_regs->hw_clkctrl_gpmi,
- CLKCTRL_GPMI_CLKGATE | CLKCTRL_GPMI_DIV_MASK, 1);
+ CLKCTRL_GPMI_DIV_MASK, 1);
udelay(1000);
/*
* This delay function is intended to be used only in early stage of boot, where
- * clock are not set up yet. The timer used here is reset on every boot and
- * takes a few seconds to roll. The boot doesn't take that long, so to keep the
- * code simple, it doesn't take rolling into consideration.
+ * clock are not set up yet.
*/
void early_delay(int delay)
{
(struct mxs_digctl_regs *)MXS_DIGCTL_BASE;
uint32_t st = readl(&digctl_regs->hw_digctl_microseconds);
- st += delay;
- while (st > readl(&digctl_regs->hw_digctl_microseconds))
+ while (readl(&digctl_regs->hw_digctl_microseconds) - st <= delay)
;
}
vf610-pcm052.dtb \
vf610-bk4r1.dtb
+dtb-$(CONFIG_MX28) += \
+ imx28-xea.dtb
+
dtb-$(CONFIG_MX53) += imx53-cx9020.dtb \
imx53-kp.dtb \
imx53-m53menlo.dtb
ifneq ($(CONFIG_MX6DL)$(CONFIG_MX6QDL)$(CONFIG_MX6S),)
dtb-y += \
+ imx6dl-aristainetos2_4.dtb \
+ imx6dl-aristainetos2_7.dtb \
+ imx6dl-aristainetos2b_4.dtb \
+ imx6dl-aristainetos2b_7.dtb \
+ imx6dl-aristainetos2b_csl_4.dtb \
+ imx6dl-aristainetos2b_csl_7.dtb \
+ imx6dl-aristainetos2c_4.dtb \
+ imx6dl-aristainetos2c_7.dtb \
imx6dl-brppt2.dtb \
+ imx6dl-cubox-i.dtb \
+ imx6dl-cubox-i-emmc-som-v15.dtb \
+ imx6dl-cubox-i-som-v15.dtb \
imx6dl-dhcom-pdk2.dtb \
+ imx6dl-hummingboard2.dtb \
+ imx6dl-hummingboard2-emmc-som-v15.dtb \
+ imx6dl-hummingboard2-som-v15.dtb \
+ imx6dl-hummingboard.dtb \
+ imx6dl-hummingboard-emmc-som-v15.dtb \
+ imx6dl-hummingboard-som-v15.dtb \
imx6dl-icore.dtb \
imx6dl-icore-mipi.dtb \
imx6dl-icore-rqs.dtb \
dtb-y += \
imx6-apalis.dtb \
imx6q-cm-fx6.dtb \
+ imx6q-cubox-i.dtb \
+ imx6q-cubox-i-emmc-som-v15.dtb \
+ imx6q-cubox-i-som-v15.dtb \
imx6q-dhcom-pdk2.dtb \
imx6q-display5.dtb \
+ imx6q-hummingboard2.dtb \
+ imx6q-hummingboard2-emmc-som-v15.dtb \
+ imx6q-hummingboard2-som-v15.dtb \
+ imx6q-hummingboard.dtb \
+ imx6q-hummingboard-emmc-som-v15.dtb \
+ imx6q-hummingboard-som-v15.dtb \
imx6q-icore.dtb \
imx6q-icore-mipi.dtb \
imx6q-icore-rqs.dtb \
imx6ul-9x9-evk.dtb \
imx6ul-9x9-evk.dtb \
imx6ul-liteboard.dtb \
- imx6ul-phycore-segin.dtb \
+ imx6ul-phytec-segin-ff-rdk-nand.dtb \
imx6ul-pico-hobbit.dtb \
imx6ul-pico-pi.dtb
dtb-$(CONFIG_MX6ULL) += \
imx6ull-14x14-evk.dtb \
imx6ull-colibri.dtb \
- imx6ull-phycore-segin.dtb \
+ imx6ull-phytec-segin-ff-rdk-emmc.dtb \
imx6ull-dart-6ul.dtb \
imx6ulz-14x14-evk.dtb
imx7d-pico-hobbit.dtb
-dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-evk.dtb
+dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-com.dtb \
+ imx7ulp-evk.dtb
dtb-$(CONFIG_ARCH_IMX8) += \
fsl-imx8qm-apalis.dtb \
mt8516-pumpkin.dtb \
mt8518-ap1-emmc.dtb
-dtb-$(CONFIG_TARGET_GE_BX50V3) += imx6q-bx50v3.dtb
+dtb-$(CONFIG_TARGET_GE_BX50V3) += \
+ imx6q-bx50v3.dtb \
+ imx6q-b850v3.dtb \
+ imx6q-b650v3.dtb \
+ imx6q-b450v3.dtb
+
dtb-$(CONFIG_TARGET_MX53PPD) += imx53-ppd.dtb
dtb-$(CONFIG_TARGET_VEXPRESS_CA5X2) += vexpress-v2p-ca5s.dtb
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/*
+ * The minimal augmentation DTS U-Boot file to allow eMMC driver
+ * configuration in SPL for falcon boot.
+ */
+#include "imx28-u-boot.dtsi"
+/ {
+ apb@80000000 {
+ u-boot,dm-spl;
+
+ apbh@80000000 {
+ u-boot,dm-spl;
+ };
+
+ apbx@80040000 {
+ u-boot,dm-spl;
+ };
+ };
+};
+
+&clks {
+ u-boot,dm-spl;
+};
+
+&gpio0 {
+ u-boot,dm-spl;
+};
+
+&pinctrl {
+ u-boot,dm-spl;
+};
+
+&ssp0 {
+ u-boot,dm-spl;
+};
+
+&ssp3 {
+ u-boot,dm-spl;
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ *
+ */
+
+/dts-v1/;
+
+#include "imx28.dtsi"
+
+/ {
+ model = "Liebherr (LWE) XEA i.MX28 Board";
+ compatible = "lwe,xea", "fsl,imx28";
+
+ aliases {
+ spi3 = &ssp3;
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x40000000 0x10000000>;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_fec_3v3: regulator-fec-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "fec-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-supply = <®_fec_3v3>;
+ phy-reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <1>;
+ phy-reset-post-delay = <1>;
+ status = "okay";
+
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a>;
+ bus-width = <8>;
+ vmmc-supply = <®_3p3v>;
+ non-removable;
+ status = "okay";
+};
+
+&ssp3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi3_pins_b>;
+ status = "okay";
+ spi-max-frequency = <40000000>;
+ num-cs = <2>;
+
+ flash0: s25fl256s@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <40000000>;
+ reg = <0>;
+
+ partition@0 {
+ label = "SPL (spi)";
+ reg = <0x0 0x10000>;
+ read-only;
+ };
+ partition@1 {
+ label = "u-boot (spi)";
+ reg = <0x10000 0x70000>;
+ read-only;
+ };
+ partition@2 {
+ label = "uboot-env (spi)";
+ reg = <0x80000 0x20000>;
+ };
+ partition@3 {
+ label = "kernel (spi)";
+ reg = <0x100000 0x400000>;
+ };
+ partition@4 {
+ label = "swupdate (spi)";
+ reg = <0x50000 0x800000>;
+ };
+ };
+};
MX53_PAD_GPIO_1__GPIO1_1 0x80000000
MX53_PAD_GPIO_4__GPIO1_4 0x80000000
MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000
- MX53_PAD_PATA_DA_2__GPIO7_8 0x80000000
MX53_PAD_GPIO_16__GPIO7_11 0x80000000
MX53_PAD_EIM_OE__EMI_WEIM_OE 0x80000000
MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x80000000
MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD 0x80000000
- MX53_PAD_FEC_MDC__FEC_MDC 0x4
- MX53_PAD_FEC_MDIO__FEC_MDIO 0x1fc
- MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x180
- MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x180
- MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x180
- MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x180
- MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x180
- MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x4
- MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x4
- MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x4
-
MX53_PAD_CSI0_DAT8__I2C1_SDA 0x400001ec
MX53_PAD_CSI0_DAT9__I2C1_SCL 0x400001ec
>;
};
+ pinctrl_fec0: fec0grp {
+ fsl,pins = <
+ MX53_PAD_FEC_MDC__FEC_MDC 0x4
+ MX53_PAD_FEC_MDIO__FEC_MDIO 0x1fc
+ MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x180
+ MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x180
+ MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x180
+ MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x180
+ MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x180
+ MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x4
+ MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x4
+ MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x4
+ >;
+ };
+
pinctrl_esdhc1: esdhc1grp {
fsl,pins = <
MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5
pinctrl-names = "default";
phy-mode = "rmii";
phy-reset-gpios = <&gpio7 6 0>;
+ pinctrl-0 = <&pinctrl_fec0>;
+ status = "okay";
+ fixed-link { /* RMII fixed link to KZ8863 */
+ speed = <100>;
+ full-duplex;
+ };
+};
+
+&usbh1 {
+ phy_type = "utmi";
+ status = "okay";
+};
+
+&usbotg {
+ dr_mode = "host";
status = "okay";
};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Copyright 2019 Collabora Ltd
+ * Copyright 2019 General Electric Company
+ */
+
+/ {
+ wdt-reboot {
+ compatible = "wdt-reboot";
+ wdt = <&wdog1>;
+ };
+};
-/* SPDX-License-Identifier: GPL-2.0+ OR X11 */
+// SPDX-License-Identifier: GPL-2.0+
/*
- * Copyright 2018 General Electric Company
- * Based on imx53-ppd.dts from kernel 4.20.5.
+ * Copyright 2014 General Electric Company
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "imx53.dtsi"
+#include "imx53-ppd-uboot.dtsi"
+#include <dt-bindings/input/input.h>
/ {
model = "General Electric CS ONE";
compatible = "ge,imx53-cpuvo", "fsl,imx53";
+
+ aliases {
+ spi0 = &cspi;
+ spi1 = &ecspi1;
+ spi2 = &ecspi2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@70000000 {
+ device_type = "memory";
+ reg = <0x70000000 0x20000000>,
+ <0xb0000000 0x20000000>;
+ };
+
+ cko2_11M: sgtl-clock-cko2 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <11289600>;
+ };
+
+ sgtlsound: sound {
+ compatible = "fsl,imx53-cpuvo-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx53-cpuvo-sgtl5000";
+ ssi-controller = <&ssi2>;
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <2>;
+ mux-ext-port = <6>;
+ };
+
+ reg_sgtl5k: regulator-sgtl5k {
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-sgtl5k";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbotg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-0 = <&pinctrl_usb_otg_vbus>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_vbus: regulator-usb-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usbh2_vbus: regulator-usbh2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh2_vbus>;
+ gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usbh3_vbus: regulator-usbh3-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh3_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh3_vbus>;
+ gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_tsiref: regulator-tsiref {
+ compatible = "regulator-fixed";
+ regulator-name = "tsiref";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reg_3v3: regulator-3v3 {
+ /* TPS54320 */
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_3v3_lcd: regulator-3v3-lcd {
+ /* MIC2009 */
+ compatible = "regulator-fixed";
+ regulator-name = "LCD_3V3";
+ vin-supply = <®_3v3>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ pwm_bl: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 50000>;
+ brightness-levels = <0 2 5 7 10 12 15 17 20 22 25 28 30 33 35
+ 38 40 43 45 48 51 53 56 58 61 63 66 68 71
+ 73 76 79 81 84 86 89 91 94 96 99 102 104
+ 107 109 112 114 117 119 122 124 127 130
+ 132 135 137 140 142 145 147 150 153 155
+ 158 160 163 165 168 170 173 175 178 181
+ 183 186 188 191 193 196 198 201 204 206
+ 209 211 214 216 219 221 224 226 229 232
+ 234 237 239 242 244 247 249 252 255>;
+ default-brightness-level = <0>;
+ enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+ power-supply = <®_3v3_lcd>;
+ };
+
+ leds {
+ compatible = "pwm-leds";
+
+ alarm-brightness {
+ pwms = <&pwm1 0 100000>;
+ max-brightness = <255>;
+ };
+ };
+
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio3 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio-restart {
+ compatible = "gpio-restart";
+ gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
+ active-delay = <100>;
+ inactive-delay = <10>;
+ wait-delay = <100>;
+ };
+
+ power-gpio-keys {
+ compatible = "gpio-keys";
+
+ power-button {
+ label = "Power button";
+ gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_POWER>;
+ };
+ };
+
+ touch-lock-key {
+ compatible = "gpio-keys";
+
+ touch-lock-button {
+ label = "Touch lock button";
+ gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_F12>;
+ };
+ };
+
+ usbphy2: usbphy-2 {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <®_3v3>;
+ reset-gpios = <&gpio4 4 GPIO_ACTIVE_LOW>;
+ clock-names = "main_clk";
+ clock-frequency = <24000000>;
+ clocks = <&clks IMX5_CLK_CKO2>;
+ assigned-clocks = <&clks IMX5_CLK_CKO2_SEL>, <&clks IMX5_CLK_OSC>;
+ assigned-clock-parents = <&clks IMX5_CLK_OSC>;
+ };
+
+ usbphy3: usbphy-3 {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <®_3v3>;
+ reset-gpios = <&gpio2 19 GPIO_ACTIVE_LOW>;
+ clock-names = "main_clk";
+
+ clock-frequency = <24000000>;
+ clocks = <&clks IMX5_CLK_CKO2>;
+ assigned-clocks = <&clks IMX5_CLK_CKO2_SEL>, <&clks IMX5_CLK_OSC>;
+ assigned-clock-parents = <&clks IMX5_CLK_OSC>;
+ };
+
+ panel-lvds0 {
+ compatible = "nvd,9128";
+ power-supply = <®_3v3_lcd>;
+
+ port {
+ panel_in_lvds0: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
};
-&iomuxc {
+&usbphy0 {
+ vcc-supply = <®_3v3>;
+};
+
+&usbphy1 {
+ vcc-supply = <®_3v3>;
+};
+
+&audmux {
pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+};
- pinctrl_esdhc3: esdhc3grp {
- fsl,pins = <
- MX53_PAD_PATA_DATA8__ESDHC3_DAT0 0x1d5
- MX53_PAD_PATA_DATA9__ESDHC3_DAT1 0x1d5
- MX53_PAD_PATA_DATA10__ESDHC3_DAT2 0x1d5
- MX53_PAD_PATA_DATA11__ESDHC3_DAT3 0x1d5
- MX53_PAD_PATA_DATA0__ESDHC3_DAT4 0x1d5
- MX53_PAD_PATA_DATA1__ESDHC3_DAT5 0x1d5
- MX53_PAD_PATA_DATA2__ESDHC3_DAT6 0x1d5
- MX53_PAD_PATA_DATA3__ESDHC3_DAT7 0x1d5
- MX53_PAD_PATA_RESET_B__ESDHC3_CMD 0x1d5
- MX53_PAD_PATA_IORDY__ESDHC3_CLK 0x1d5
- >;
+&cpu0 {
+ /* CPU rated to 1GHz, not 1.2GHz as per the default settings */
+ operating-points = <
+ /* kHz uV */
+ 166666 850000
+ 400000 900000
+ 800000 1050000
+ 1000000 1200000
+ >;
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio5 17 GPIO_ACTIVE_LOW
+ &gpio4 10 GPIO_ACTIVE_LOW
+ &gpio4 11 GPIO_ACTIVE_LOW
+ &gpio4 12 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ spidev0: spi@0 {
+ compatible = "ge,achc";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ };
+
+ spidev1: spi@1 {
+ compatible = "ge,achc";
+ reg = <1>;
+ spi-max-frequency = <1000000>;
+ };
+
+ gpioxra0: gpio@2 {
+ compatible = "exar,xra1403";
+ reg = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ spi-max-frequency = <1000000>;
+ };
+
+ gpioxra1: gpio@3 {
+ compatible = "exar,xra1403";
+ reg = <3>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ spi-max-frequency = <1000000>;
+ };
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ da9053@0 {
+ compatible = "dlg,da9053-aa";
+ reg = <0>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+ spi-max-frequency = <1000000>;
+ dlg,tsi-as-adc;
+ tsiref-supply = <®_tsiref>;
+
+ regulators {
+ buck1_reg: buck1 {
+ regulator-name = "BUCKCORE";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2075000>;
+ regulator-always-on;
+ };
+
+ buck2_reg: buck2 {
+ regulator-name = "BUCKPRO";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2075000>;
+ regulator-always-on;
+ };
+
+ buck3_reg: buck3 {
+ regulator-name = "BUCKMEM";
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ buck4_reg: buck4 {
+ regulator-name = "BUCKPERI";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-always-on;
+ };
+
+ ldo1_reg: ldo1 {
+ regulator-name = "ldo1_1v3";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo2_reg: ldo2 {
+ regulator-name = "ldo2_1v3";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo3_reg: ldo3 {
+ regulator-name = "ldo3_3v3";
+ regulator-min-microvolt = <1725000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: ldo4 {
+ regulator-name = "ldo4_2v775";
+ regulator-min-microvolt = <1725000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo5_reg: ldo5 {
+ regulator-name = "ldo5_3v3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: ldo6 {
+ regulator-name = "ldo6_1v3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-always-on;
+ };
+
+ ldo7_reg: ldo7 {
+ regulator-name = "ldo7_2v75";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-always-on;
+ };
+
+ ldo8_reg: ldo8 {
+ regulator-name = "ldo8_1v8";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-always-on;
+ };
+
+ ldo9_reg: ldo9 {
+ regulator-name = "ldo9_1v5";
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <3650000>;
+ regulator-always-on;
+ };
+
+ ldo10_reg: ldo10 {
+ regulator-name = "ldo10_1v3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-always-on;
+ };
+ };
};
+
};
-/* eMMC */
&esdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_esdhc3>;
- compatible = "fsl,esdhc";
bus-width = <8>;
non-removable;
status = "okay";
};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec>;
+ phy-supply = <®_3v3>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio2 16 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ sda-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ i2c-switch@70 {
+ compatible = "nxp,pca9547";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+ reset-gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
+
+ i2c4: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ #sound-dai-cells = <0>;
+ VDDA-supply = <®_sgtl5k>;
+ VDDIO-supply = <®_sgtl5k>;
+ clocks = <&cko2_11M>;
+ status = "okay";
+ };
+ };
+
+ i2c5: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ rtc@30 {
+ compatible = "sii,s35390a";
+ reg = <0x30>;
+ };
+
+ temp@48 {
+ compatible = "ti,tmp112";
+ reg = <0x48>;
+ };
+
+ mma8453q: accelerometer@1c {
+ compatible = "fsl,mma8453";
+ reg = <0x1c>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <6 IRQ_TYPE_NONE>;
+ interrupt-names = "INT1";
+ };
+
+ mpl3115: pressure-sensor@60 {
+ compatible = "fsl,mpl3115";
+ reg = <0x60>;
+ };
+
+ eeprom: eeprom@50 {
+ compatible = "atmel,24c08";
+ reg = <0x50>;
+ };
+ };
+
+ i2c6: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c7: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ i2c8: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ i2c9: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ i2c10: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ i2c11: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ sda-gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ touchscreen@4b {
+ compatible = "atmel,maxtouch";
+ reset-gpio = <&gpio5 19 GPIO_ACTIVE_HIGH>;
+ reg = <0x4b>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c3 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ sda-gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel@0 {
+ status = "okay";
+
+ port@2 {
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in_lvds0>;
+ };
+ };
+ };
+};
+
+&pmu {
+ secure-reg-access;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&ssi2 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ dr_mode = "otg";
+ phy_type = "utmi";
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-0 = <&pinctrl_usb_otg>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_vbus>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbh2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh2>;
+ phy_type = "ulpi";
+ dr_mode = "host";
+ fsl,usbphy = <&usbphy2>;
+ vbus-supply = <®_usbh2_vbus>;
+ status = "okay";
+};
+
+&usbh3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh3>;
+ phy_type = "ulpi";
+ dr_mode = "host";
+ vbus-supply = <®_usbh3_vbus>;
+ fsl,usbphy = <&usbphy3>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog_rev6>;
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX53_PAD_DISP0_DAT19__AUDMUX_AUD5_RXD 0x400
+ MX53_PAD_DISP0_DAT17__AUDMUX_AUD5_TXD 0x400
+ MX53_PAD_DISP0_DAT16__AUDMUX_AUD5_TXC 0x400
+ MX53_PAD_DISP0_DAT18__AUDMUX_AUD5_TXFS 0x400
+ MX53_PAD_DI0_PIN15__AUDMUX_AUD6_TXC 0x400
+ MX53_PAD_DI0_PIN3__AUDMUX_AUD6_TXFS 0x400
+ MX53_PAD_DI0_PIN4__AUDMUX_AUD6_RXD 0x400
+ MX53_PAD_DI0_PIN2__AUDMUX_AUD6_TXD 0x400
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX53_PAD_DISP0_DAT21__ECSPI1_MOSI 0x400
+ MX53_PAD_DISP0_DAT22__ECSPI1_MISO 0x400
+ MX53_PAD_DISP0_DAT20__ECSPI1_SCLK 0x400
+ /* ECSPI1_SS0, must treat as GPIO for EzPort */
+ MX53_PAD_DISP0_DAT23__GPIO5_17 0x400
+ MX53_PAD_KEY_COL2__GPIO4_10 0x0
+ MX53_PAD_KEY_ROW2__GPIO4_11 0x0
+ MX53_PAD_KEY_COL3__GPIO4_12 0x0
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX53_PAD_EIM_CS1__ECSPI2_MOSI 0x0
+ MX53_PAD_EIM_OE__ECSPI2_MISO 0x0
+ MX53_PAD_EIM_CS0__ECSPI2_SCLK 0x0
+ MX53_PAD_EIM_RW__GPIO2_26 0x0
+ >;
+ };
+
+ pinctrl_esdhc1: esdhc1grp {
+ fsl,pins = <
+ MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5
+ MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5
+ MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5
+ MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5
+ MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5
+ MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5
+ >;
+ };
+
+ pinctrl_esdhc3: esdhc3grp {
+ fsl,pins = <
+ MX53_PAD_PATA_DATA8__ESDHC3_DAT0 0x1d5
+ MX53_PAD_PATA_DATA9__ESDHC3_DAT1 0x1d5
+ MX53_PAD_PATA_DATA10__ESDHC3_DAT2 0x1d5
+ MX53_PAD_PATA_DATA11__ESDHC3_DAT3 0x1d5
+ MX53_PAD_PATA_DATA0__ESDHC3_DAT4 0x1d5
+ MX53_PAD_PATA_DATA1__ESDHC3_DAT5 0x1d5
+ MX53_PAD_PATA_DATA2__ESDHC3_DAT6 0x1d5
+ MX53_PAD_PATA_DATA3__ESDHC3_DAT7 0x1d5
+ MX53_PAD_PATA_RESET_B__ESDHC3_CMD 0x1d5
+ MX53_PAD_PATA_IORDY__ESDHC3_CLK 0x1d5
+ >;
+ };
+
+ pinctrl_fec: fecgrp {
+ fsl,pins = <
+ MX53_PAD_FEC_MDC__FEC_MDC 0x0
+ MX53_PAD_FEC_MDIO__FEC_MDIO 0x0
+ MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x0
+ MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x0
+ MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x0
+ MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x0
+ MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x0
+ MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x0
+ MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x0
+ MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x0
+ >;
+ };
+
+ pinctrl_hog_rev6: hoggrp {
+ fsl,pins = <
+ /* CKO2 */
+ MX53_PAD_GPIO_3__CCM_CLKO2 0x4
+ /* DEFIB_SYNC_MARKER_IN_IRQ */
+ MX53_PAD_GPIO_5__GPIO1_5 0x0
+ /* ACCELEROMETER_DATA_RDY_N */
+ MX53_PAD_GPIO_6__GPIO1_6 0x0
+ /* TEMPERATURE_ALERT_N */
+ MX53_PAD_GPIO_7__GPIO1_7 0x0
+ /* BAROMETRIC_PRESSURE_DATA_RDY_N */
+ MX53_PAD_GPIO_8__GPIO1_8 0x0
+ /* DOCKING_I2C_INTERFACE_IRQ_N */
+ MX53_PAD_PATA_DATA4__GPIO2_4 0x0
+ /* PWR_OUT_TO_DOCK_FAULT_N */
+ MX53_PAD_PATA_DATA5__GPIO2_5 0x0
+ /* ENABLE_PWR_TO_DOCK_N */
+ MX53_PAD_PATA_DATA6__GPIO2_6 0x0
+ /* HOST_CONTROLLED_RESET_TO_DOCKING_CONNECTOR_N */
+ MX53_PAD_PATA_DATA7__GPIO2_7 0x0
+ /* REMOTE_ON_REQUEST_FROM_DOCKING_CONNECTOR_IS_ACTIVE_N */
+ MX53_PAD_PATA_DATA12__GPIO2_12 0x0
+ /* DOCK_PRESENT_N */
+ MX53_PAD_PATA_DATA13__GPIO2_13 0x0
+ /* ECG_MARKER_IN_FROM_DOCKING_CONNECTOR_IRQ */
+ MX53_PAD_PATA_DATA14__GPIO2_14 0x0
+ /* ENABLE_ECG_MARKER_INTERFACE_TO_DOCKING_CONNECTOR */
+ MX53_PAD_PATA_DATA15__GPIO2_15 0x0
+ /* RESET_IMX535_ETHERNET_PHY_N */
+ MX53_PAD_EIM_A22__GPIO2_16 0x0
+ /* ENABLE_PWR_TO_LCD_AND_UI_INTERFACE */
+ MX53_PAD_EIM_A21__GPIO2_17 0x0
+ /* RESET_I2C1_BUS_SEGMENT_MUX_N */
+ MX53_PAD_EIM_A20__GPIO2_18 0x0
+ /* RESET_IMX535_USB_HOST3_PHY_N */
+ MX53_PAD_EIM_A19__GPIO2_19 0x0
+ /* ESDHC3_EMMC_NAND_RST_N */
+ MX53_PAD_EIM_A18__GPIO2_20 0x0
+ /* LCD_AND_UI_INTERFACE_PWR_FAULT_N */
+ MX53_PAD_EIM_A17__GPIO2_21 0x0
+ /* POWER_DOWN_LVDS0_DESERIALIZER_N */
+ MX53_PAD_EIM_A16__GPIO2_22 0x0
+ /* POWER_DOWN_LVDS1_DESERIALIZER_N */
+ MX53_PAD_EIM_LBA__GPIO2_27 0x0
+ /* RESET_DP0_TRANSMITTER_N */
+ MX53_PAD_EIM_EB0__GPIO2_28 0x0
+ /* RESET_DP1_TRANSMITTER_N */
+ MX53_PAD_EIM_EB1__GPIO2_29 0x0
+ /* ENABLE_SPDIF_AUDIO_TO_DP0 */
+ MX53_PAD_EIM_DA0__GPIO3_0 0x0
+ /* ENABLE_SPDIF_AUDIO_TO_DP1 */
+ MX53_PAD_EIM_DA1__GPIO3_1 0x0
+ /* LVDS1_MUX_CTRL */
+ MX53_PAD_EIM_DA2__GPIO3_2 0x0
+ /* LVDS0_MUX_CTRL */
+ MX53_PAD_EIM_DA3__GPIO3_3 0x0
+ /* DP1_TRANSMITTER_IRQ */
+ MX53_PAD_EIM_DA4__GPIO3_4 0x0
+ /* DP0_TRANSMITTER_IRQ */
+ MX53_PAD_EIM_DA5__GPIO3_5 0x0
+ /* USB_RESET_N */
+ MX53_PAD_EIM_DA6__GPIO3_6 0x0
+ /* ENABLE_BATTERY_CHARGER */
+ MX53_PAD_EIM_DA7__GPIO3_7 0x0
+ /* SOFTWARE_CONTROLLED_PWR_CYCLE */
+ MX53_PAD_EIM_DA8__GPIO3_8 0x0
+ /* SOFTWARE_CONTROLLED_POWERDOWN */
+ MX53_PAD_EIM_DA9__GPIO3_9 0x0
+ /* DC_PWR_IN_OK */
+ MX53_PAD_EIM_DA10__GPIO3_10 0x0
+ /* BATT_PRESENT_N */
+ MX53_PAD_EIM_DA11__GPIO3_11 0xe4
+ /* PMIC_IRQ_N */
+ MX53_PAD_EIM_DA12__GPIO3_12 0x0
+ /* PMIC_VDD_FAULT_STATUS_N */
+ MX53_PAD_EIM_DA13__GPIO3_13 0x0
+ /* IMX535_ETHERNET_PHY_STATUS_IRQ_N */
+ MX53_PAD_EIM_DA14__GPIO3_14 0x0
+ /* NOT USED - AVAILABLE 3.3V GPIO */
+ MX53_PAD_EIM_DA15__GPIO3_15 0x0
+ /* NOT USED - AVAILABLE 3.3V GPIO */
+ MX53_PAD_EIM_D22__GPIO3_22 0x0
+ /* NOT USED - AVAILABLE 3.3V GPIO */
+ MX53_PAD_EIM_D24__GPIO3_24 0x0
+ /* NBP_PUMP_VALVE_PWR_ENABLE */
+ MX53_PAD_EIM_D25__GPIO3_25 0x0
+ /* NIBP_RESET_N */
+ MX53_PAD_EIM_D26__GPIO3_26 0x0
+ /* LATCHED_OVERPRESSURE_N */
+ MX53_PAD_EIM_D27__GPIO3_27 0x0
+ /* NBP_SBWTCLK */
+ MX53_PAD_EIM_D29__GPIO3_29 0x0
+ /* ENABLE_WIFI_MODULE */
+ MX53_PAD_GPIO_11__GPIO4_1 0x400
+ /* WIFI_MODULE_IRQ_N */
+ MX53_PAD_GPIO_12__GPIO4_2 0x400
+ /* ENABLE_BLUETOOTH_MODULE */
+ MX53_PAD_GPIO_13__GPIO4_3 0x400
+ /* RESET_IMX535_USB_HOST2_PHY_N */
+ MX53_PAD_GPIO_14__GPIO4_4 0x400
+ /* ONKEY_IS_DEPRESSED */
+ MX53_PAD_KEY_ROW3__GPIO4_13 0x0
+ /* UNUSED_GPIO_TO_ALARM_LIGHT_BOARD */
+ MX53_PAD_EIM_WAIT__GPIO5_0 0x0
+ /* DISPLAY_LOCK_BUTTON_IS_DEPRESSED_N */
+ MX53_PAD_EIM_A25__GPIO5_2 0x0
+ /* I2C_PCAP_TOUCHSCREEN_IRQ_N */
+ MX53_PAD_EIM_A24__GPIO5_4 0x0
+ /* NOT USED - AVAILABLE 1.8V GPIO */
+ MX53_PAD_DISP0_DAT13__GPIO5_7 0x400
+ /* NOT USED - AVAILABLE 1.8V GPIO */
+ MX53_PAD_DISP0_DAT14__GPIO5_8 0x400
+ /* NOT USED - AVAILABLE 1.8V GPIO */
+ MX53_PAD_DISP0_DAT15__GPIO5_9 0x400
+ /* HOST_CONTROLLED_RESET_TO_LCD_N */
+ MX53_PAD_CSI0_PIXCLK__GPIO5_18 0x0
+ /* HOST_CONTROLLED_RESET_TO_PCAP_N */
+ MX53_PAD_CSI0_MCLK__GPIO5_19 0x0
+ /* LR_SCAN_CTRL */
+ MX53_PAD_CSI0_DATA_EN__GPIO5_20 0x0
+ /* UD_SCAN_CTRL */
+ MX53_PAD_CSI0_VSYNC__GPIO5_21 0x0
+ /* DATA_WIDTH_CTRL */
+ MX53_PAD_CSI0_DAT10__GPIO5_28 0x0
+ /* BACKLIGHT_ENABLE */
+ MX53_PAD_CSI0_DAT11__GPIO5_29 0x0
+ /* MED_USB_PORT_1_HOST_SELECT */
+ MX53_PAD_EIM_A23__GPIO6_6 0x0
+ /* MED_USB_PORT_2_HOST_SELECT */
+ MX53_PAD_NANDF_CLE__GPIO6_7 0x0
+ /* MED_USB_PORT_3_HOST_SELECT */
+ MX53_PAD_NANDF_ALE__GPIO6_8 0x0
+ /* MED_USB_PORT_4_HOST_SELECT */
+ MX53_PAD_NANDF_WP_B__GPIO6_9 0x0
+ /* MED_USB_PORT_5_HOST_SELECT */
+ MX53_PAD_NANDF_RB0__GPIO6_10 0x0
+ /* MED_USB_PORT_6_HOST_SELECT */
+ MX53_PAD_NANDF_CS0__GPIO6_11 0x0
+ /* MED_USB_PORT_7_HOST_SELECT */
+ MX53_PAD_NANDF_WE_B__GPIO6_12 0x0
+ /* MED_USB_PORT_8_HOST_SELECT */
+ MX53_PAD_NANDF_RE_B__GPIO6_13 0x0
+ /* MED_USB_PORT_TO_IMX_SELECT_0 */
+ MX53_PAD_NANDF_CS1__GPIO6_14 0x0
+ /* MED_USB_PORT_TO_IMX_SELECT_1 */
+ MX53_PAD_NANDF_CS2__GPIO6_15 0x0
+ /* MED_USB_PORT_TO_IMX_SELECT_2 */
+ MX53_PAD_NANDF_CS3__GPIO6_16 0x0
+ /* POWER_AND_BOOT_STATUS_INDICATOR */
+ MX53_PAD_PATA_INTRQ__GPIO7_2 0x1e4
+ /* ACTIVATE_ALARM_LIGHT_RED */
+ MX53_PAD_PATA_DIOR__GPIO7_3 0x0
+ /* ACTIVATE_ALARM_LIGHT_YELLOW */
+ MX53_PAD_PATA_DA_1__GPIO7_7 0x0
+ /* ACTIVATE_ALARM_LIGHT_CYAN */
+ MX53_PAD_PATA_DA_2__GPIO7_8 0x0
+ /* RUNNING_ON_BATTERY_INDICATOR_GREEN */
+ MX53_PAD_GPIO_16__GPIO7_11 0x0
+ /* BATTERY_STATUS_INDICATOR_AMBER */
+ MX53_PAD_GPIO_17__GPIO7_12 0x0
+ /* AUDIO_ALARMS_SILENCED_INDICATOR */
+ MX53_PAD_GPIO_18__GPIO7_13 0x0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX53_PAD_EIM_D21__I2C1_SCL 0x400001e4
+ MX53_PAD_EIM_D28__I2C1_SDA 0x400001e4
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX53_PAD_EIM_D28__GPIO3_28 0x1e4
+ MX53_PAD_EIM_D21__GPIO3_21 0x1e4
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX53_PAD_EIM_EB2__I2C2_SCL 0x400001e4
+ MX53_PAD_EIM_D16__I2C2_SDA 0x400001e4
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX53_PAD_EIM_D16__GPIO3_16 0x1e4
+ MX53_PAD_EIM_EB2__GPIO2_30 0x1e4
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX53_PAD_EIM_D17__I2C3_SCL 0x400001e4
+ MX53_PAD_EIM_D18__I2C3_SDA 0x400001e4
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX53_PAD_EIM_D18__GPIO3_18 0x1e4
+ MX53_PAD_EIM_D17__GPIO3_17 0x1e4
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX53_PAD_GPIO_9__PWM1_PWMO 0x5
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX53_PAD_DISP0_DAT9__PWM2_PWMO 0x5
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4
+ MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4
+ MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4
+ MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4
+ MX53_PAD_EIM_D23__UART3_CTS 0x1e4
+ MX53_PAD_EIM_EB3__UART3_RTS 0x1e4
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX53_PAD_KEY_COL0__UART4_TXD_MUX 0x1e4
+ MX53_PAD_KEY_ROW0__UART4_RXD_MUX 0x1e4
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX53_PAD_KEY_COL1__UART5_TXD_MUX 0x1e4
+ MX53_PAD_KEY_ROW1__UART5_RXD_MUX 0x1e4
+ >;
+ };
+
+ pinctrl_usb_otg_vbus: usb-otg-vbusgrp {
+ fsl,pins = <
+ /* USB_HS_OTG_VBUS_ENABLE */
+ MX53_PAD_KEY_ROW4__GPIO4_15 0x1c4
+ >;
+ };
+
+ pinctrl_usbh2: usbh2grp {
+ fsl,pins = <
+ /* USB H2 */
+ MX53_PAD_DISP0_DAT0__USBOH3_USBH2_DATA_0 0x180
+ MX53_PAD_DISP0_DAT1__USBOH3_USBH2_DATA_1 0x180
+ MX53_PAD_DISP0_DAT2__USBOH3_USBH2_DATA_2 0x180
+ MX53_PAD_DISP0_DAT3__USBOH3_USBH2_DATA_3 0x180
+ MX53_PAD_DISP0_DAT4__USBOH3_USBH2_DATA_4 0x180
+ MX53_PAD_DISP0_DAT5__USBOH3_USBH2_DATA_5 0x180
+ MX53_PAD_DISP0_DAT6__USBOH3_USBH2_DATA_6 0x180
+ MX53_PAD_DISP0_DAT7__USBOH3_USBH2_DATA_7 0x180
+ MX53_PAD_DISP0_DAT10__USBOH3_USBH2_STP 0x180
+ MX53_PAD_DISP0_DAT11__USBOH3_USBH2_NXT 0x180
+ MX53_PAD_DISP0_DAT12__USBOH3_USBH2_CLK 0x180
+ MX53_PAD_DI0_DISP_CLK__USBOH3_USBH2_DIR 0x5
+ MX53_PAD_EIM_D30__USBOH3_USBH2_OC 0x180
+ >;
+ };
+
+ pinctrl_usbh2_vbus: usbh2-vbusgrp {
+ fsl,pins = <
+ /* USB_HS_HOST2_VBUS_ENABLE */
+ MX53_PAD_EIM_D31__GPIO3_31 0x0
+ >;
+ };
+
+ pinctrl_usbh3_vbus: usbh3-vbusgrp {
+ fsl,pins = <
+ /* USB_HS_HOST3_VBUS_ENABLE */
+ MX53_PAD_CSI0_DAT9__GPIO5_27 0x0
+ >;
+ };
+
+ pinctrl_usbh3: usbh3grp {
+ fsl,pins = <
+ /* USB H3 */
+ MX53_PAD_CSI0_DAT12__USBOH3_USBH3_DATA_0 0x180
+ MX53_PAD_CSI0_DAT13__USBOH3_USBH3_DATA_1 0x180
+ MX53_PAD_CSI0_DAT14__USBOH3_USBH3_DATA_2 0x180
+ MX53_PAD_CSI0_DAT15__USBOH3_USBH3_DATA_3 0x180
+ MX53_PAD_CSI0_DAT16__USBOH3_USBH3_DATA_4 0x180
+ MX53_PAD_CSI0_DAT17__USBOH3_USBH3_DATA_5 0x180
+ MX53_PAD_CSI0_DAT18__USBOH3_USBH3_DATA_6 0x180
+ MX53_PAD_CSI0_DAT19__USBOH3_USBH3_DATA_7 0x180
+ MX53_PAD_CSI0_DAT7__USBOH3_USBH3_DIR 0x5
+ MX53_PAD_CSI0_DAT6__USBOH3_USBH3_CLK 0x180
+ MX53_PAD_CSI0_DAT5__USBOH3_USBH3_NXT 0x180
+ MX53_PAD_CSI0_DAT4__USBOH3_USBH3_STP 0x180
+ MX53_PAD_CSI0_DAT8__USBOH3_USBH3_OC 0x180
+ >;
+ };
+
+ pinctrl_usb_otg: usbotggrp {
+ fsl,pins = <
+ /* USB_OTG_FAULT_N */
+ MX53_PAD_KEY_COL4__USBOH3_USBOTG_OC 0x180
+ >;
+ };
+};
mmc1 = &usdhc1;
mmc2 = &usdhc2;
usb0 = &usbotg; /* required for ums */
+ ethernet0 = &fec;
};
chosen {
status = "okay";
};
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy>;
+ phy-reset-duration = <10>;
+ phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@7 {
+ interrupt-parent = <&gpio1>;
+ interrupts = <30 IRQ_TYPE_LEVEL_LOW>;
+ reg = <7>;
+ };
+ };
+};
+
/* Apalis Serial ATA */
&sata {
status = "okay";
mmc0 = &usdhc3;
mmc1 = &usdhc1;
usb0 = &usbotg; /* required for ums */
+ ethernet0 = &fec;
};
chosen {
};
};
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@0 {
+ reg = <0>;
+ micrel,led-mode = <0>;
+ status = "okay";
+ };
+ };
+};
+
/*
* PWR_I2C: power I2C to audio codec, PMIC, temperature sensor and
* touch screen controller
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ */
+
+#include <imx6qdl-aristainetos2-u-boot.dtsi>
+
+&lcd_panel {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu_disp>;
+ enable-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+ backlight = <&backlight>;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2 board
+ * parts for 4.3 inch LG display on spi1 port0
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ *
+ */
+/dts-v1/;
+
+#include "imx6dl-aristainetos2_4.dtsi"
+#include "imx6qdl-aristainetos2.dtsi"
+
+/ {
+ model = "aristainetos2 i.MX6 Dual Lite Board 4";
+ compatible = "fsl,imx6dl";
+
+};
+
+&ecspi1 {
+ lcd_panel: display@0 {
+ compatible = "lg,lg4573";
+ spi-max-frequency = <10000000>;
+ reg = <0>;
+ power-on-delay = <10>;
+
+ display-timings {
+ 480x800p57 {
+ native-mode;
+ clock-frequency = <27000027>;
+ hactive = <480>;
+ vactive = <800>;
+ hfront-porch = <10>;
+ hback-porch = <59>;
+ hsync-len = <10>;
+ vback-porch = <15>;
+ vfront-porch = <15>;
+ vsync-len = <15>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2 board
+ * parts for 4.3 inch LG display on the parallel port and atmel maxtouch
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ *
+ */
+/dts-v1/;
+#include "imx6dl.dtsi"
+
+/ {
+ display0: disp0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx-parallel-display";
+ interface-pix-fmt = "rgb24";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu_disp>;
+
+ port@0 {
+ reg = <0>;
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&i2c3 {
+ touch: touch@4b {
+ compatible = "atmel,maxtouch";
+ reg = <0x4b>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <9 8>;
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+&iomuxc {
+ pinctrl_ipu_disp: ipudisp1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x31
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xE1
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xE1
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xE1
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xE1
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xE1
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xE1
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xE1
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xE1
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xE1
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xE1
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xE1
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xE1
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xE1
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xE1
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xE1
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xe1
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xE1
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xE1
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xE1
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xE1
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xE1
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xE1
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xE1
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xE1
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xE1
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ */
+
+#include <imx6qdl-aristainetos2-u-boot.dtsi>
+/ {
+ vdd_panel_reg: regulator-panel {
+ compatible = "regulator-fixed";
+ regulator-name = "panel_regulator";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+};
+
+&panel0 {
+ power-supply = <&vdd_panel_reg>;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2 board
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ *
+ */
+/dts-v1/;
+#include "imx6dl-aristainetos2_7.dtsi"
+#include "imx6qdl-aristainetos2.dtsi"
+
+/ {
+ model = "aristainetos2 i.MX6 Dual Lite Board 7";
+ compatible = "fsl,imx6dl";
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2 board
+ * parts for 7 inch LG display connected to the LVDS port and atmel maxtouch
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ *
+ */
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+
+#include "imx6dl.dtsi"
+
+/ {
+ panel0: panel_lg {
+ compatible = "lg,lb070wv8";
+ backlight = <&backlight>;
+ enable-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&i2c3 {
+ touch: touch@4d {
+ compatible = "atmel,maxtouch";
+ reg = <0x4d>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <9 8>;
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+ lvds0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_lvds0>;
+ };
+ };
+
+ port@4 {
+ reg = <4>;
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ or X11
+/*
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ */
+
+#include <imx6qdl-aristainetos2b-u-boot.dtsi>
+
+&lcd_panel {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu_disp>;
+ enable-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+ backlight = <&backlight>;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2b board
+ * parts for 4.3 inch LG display on spi1 port1
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ *
+ */
+/dts-v1/;
+
+#include "imx6dl-aristainetos2_4.dtsi"
+#include "imx6qdl-aristainetos2b.dtsi"
+
+/ {
+ model = "aristainetos2b i.MX6 Dual Lite Board 4";
+ compatible = "fsl,imx6dl";
+
+};
+
+&ecspi1 {
+ lcd_panel: display@0 {
+ compatible = "lg,lg4573";
+ spi-max-frequency = <10000000>;
+ reg = <1>;
+ power-on-delay = <10>;
+
+ display-timings {
+ 480x800p57 {
+ native-mode;
+ clock-frequency = <27000027>;
+ hactive = <480>;
+ vactive = <800>;
+ hfront-porch = <10>;
+ hback-porch = <59>;
+ hsync-len = <10>;
+ vback-porch = <15>;
+ vfront-porch = <15>;
+ vsync-len = <15>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ or X11
+/*
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ */
+
+#include <imx6qdl-aristainetos2b-u-boot.dtsi>
+/ {
+ vdd_panel_reg: regulator-panel {
+ compatible = "regulator-fixed";
+ regulator-name = "panel_regulator";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+};
+
+&panel0 {
+ power-supply = <&vdd_panel_reg>;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2 board
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ *
+ */
+/dts-v1/;
+#include "imx6dl-aristainetos2_7.dtsi"
+#include "imx6qdl-aristainetos2b.dtsi"
+
+/ {
+ model = "aristainetos2b i.MX6 Dual Lite Board 7";
+ compatible = "fsl,imx6dl";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ or X11
+/*
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ */
+
+#include <imx6qdl-aristainetos2b_csl-u-boot.dtsi>
+
+&lcd_panel {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu_disp>;
+ enable-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+ backlight = <&backlight>;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2b csl board
+ * parts for 4.3 inch LG display on spi1 port1
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ *
+ */
+/dts-v1/;
+
+#include "imx6dl-aristainetos2_4.dtsi"
+#include "imx6qdl-aristainetos2b_csl.dtsi"
+
+/ {
+ model = "aristainetos2b csl i.MX6 Dual Lite Board 4";
+ compatible = "fsl,imx6dl";
+
+};
+
+&ecspi1 {
+ lcd_panel: display@0 {
+ compatible = "lg,lg4573";
+ spi-max-frequency = <10000000>;
+ reg = <1>;
+ power-on-delay = <10>;
+
+ display-timings {
+ 480x800p57 {
+ native-mode;
+ clock-frequency = <27000027>;
+ hactive = <480>;
+ vactive = <800>;
+ hfront-porch = <10>;
+ hback-porch = <59>;
+ hsync-len = <10>;
+ vback-porch = <15>;
+ vfront-porch = <15>;
+ vsync-len = <15>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ or X11
+/*
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ */
+
+#include <imx6qdl-aristainetos2b_csl-u-boot.dtsi>
+/ {
+ vdd_panel_reg: regulator-panel {
+ compatible = "regulator-fixed";
+ regulator-name = "panel_regulator";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+};
+
+&panel0 {
+ power-supply = <&vdd_panel_reg>;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2 board
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ *
+ */
+/dts-v1/;
+#include "imx6dl-aristainetos2_7.dtsi"
+#include "imx6qdl-aristainetos2b_csl.dtsi"
+
+/ {
+ model = "aristainetos2b csl i.MX6 Dual Lite Board 7";
+ compatible = "fsl,imx6dl";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ or X11
+/*
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ */
+
+#include <imx6qdl-aristainetos2c-u-boot.dtsi>
+
+&lcd_panel {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu_disp>;
+ enable-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+ backlight = <&backlight>;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2c board
+ * parts for 4.3 inch LG display on spi1 port1
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ *
+ */
+/dts-v1/;
+
+#include "imx6dl-aristainetos2_4.dtsi"
+#include "imx6qdl-aristainetos2c.dtsi"
+
+/ {
+ model = "aristainetos2c i.MX6 Dual Lite Board 4";
+ compatible = "fsl,imx6dl";
+
+};
+
+&ecspi1 {
+ lcd_panel: display@0 {
+ compatible = "lg,lg4573";
+ spi-max-frequency = <10000000>;
+ reg = <1>;
+ power-on-delay = <10>;
+
+ display-timings {
+ 480x800p57 {
+ native-mode;
+ clock-frequency = <27000027>;
+ hactive = <480>;
+ vactive = <800>;
+ hfront-porch = <10>;
+ hback-porch = <59>;
+ hsync-len = <10>;
+ vback-porch = <15>;
+ vfront-porch = <15>;
+ vsync-len = <15>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ or X11
+/*
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ */
+
+#include <imx6qdl-aristainetos2c-u-boot.dtsi>
+/ {
+ vdd_panel_reg: regulator-panel {
+ compatible = "regulator-fixed";
+ regulator-name = "panel_regulator";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+};
+
+&panel0 {
+ power-supply = <&vdd_panel_reg>;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2c board
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ *
+ */
+/dts-v1/;
+#include "imx6dl-aristainetos2_7.dtsi"
+#include "imx6qdl-aristainetos2c.dtsi"
+
+/ {
+ model = "aristainetos2c i.MX6 Dual Lite Board 7";
+ compatible = "fsl,imx6dl";
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-sr-som-emmc.dtsi"
+#include "imx6qdl-cubox-i.dtsi"
+
+/ {
+ model = "SolidRun Cubox-i Solo/DualLite (1.5som+emmc)";
+ compatible = "solidrun,cubox-i/dl", "fsl,imx6dl";
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-cubox-i.dtsi"
+
+/ {
+ model = "SolidRun Cubox-i Solo/DualLite (1.5som)";
+ compatible = "solidrun,cubox-i/dl", "fsl,imx6dl";
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-brcm.dtsi"
+#include "imx6qdl-cubox-i.dtsi"
+
+/ {
+ model = "SolidRun Cubox-i Solo/DualLite";
+ compatible = "solidrun,cubox-i/dl", "fsl,imx6dl";
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 Rabeeh Khoury (rabeeh@solid-run.com)
+ * Based on dt work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-sr-som-emmc.dtsi"
+#include "imx6qdl-hummingboard.dtsi"
+
+/ {
+ model = "SolidRun HummingBoard Solo/DualLite (1.5som+emmc)";
+ compatible = "solidrun,hummingboard/dl", "fsl,imx6dl";
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 Rabeeh Khoury (rabeeh@solid-run.com)
+ * Based on dt work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-hummingboard.dtsi"
+
+/ {
+ model = "SolidRun HummingBoard Solo/DualLite (1.5som)";
+ compatible = "solidrun,hummingboard/dl", "fsl,imx6dl";
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 Rabeeh Khoury (rabeeh@solid-run.com)
+ * Based on dt work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-brcm.dtsi"
+#include "imx6qdl-hummingboard.dtsi"
+
+/ {
+ model = "SolidRun HummingBoard Solo/DualLite";
+ compatible = "solidrun,hummingboard/dl", "fsl,imx6dl";
+};
--- /dev/null
+#include "imx6qdl-hummingboard2-emmc-som-v15-u-boot.dtsi"
--- /dev/null
+/*
+ * Device Tree file for SolidRun HummingBoard2
+ * Copyright (C) 2015 Rabeeh Khoury <rabeeh@solid-run.com>
+ * Based on work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-emmc.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-hummingboard2.dtsi"
+
+/ {
+ model = "SolidRun HummingBoard2 Solo/DualLite (1.5som+emmc)";
+ compatible = "solidrun,hummingboard2/dl", "fsl,imx6dl";
+};
--- /dev/null
+/*
+ * Device Tree file for SolidRun HummingBoard2
+ * Copyright (C) 2015 Rabeeh Khoury <rabeeh@solid-run.com>
+ * Based on work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-hummingboard2.dtsi"
+
+/ {
+ model = "SolidRun HummingBoard2 Solo/DualLite (1.5som)";
+ compatible = "solidrun,hummingboard2/dl", "fsl,imx6dl";
+};
--- /dev/null
+/*
+ * Copyright (C) 2015 Rabeeh Khoury <rabeeh@solid-run.com>
+ * Based on dt work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-brcm.dtsi"
+#include "imx6qdl-hummingboard2.dtsi"
+#include "imx6qdl-hummingboard2-emmc.dtsi"
+
+/ {
+ model = "SolidRun HummingBoard2 Solo/DualLite";
+ compatible = "solidrun,hummingboard2/dl", "fsl,imx6dl";
+};
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// SPDX-License-Identifier: GPL-2.0 OR X11
/*
- * Copyright (C) 2017 Engicam S.r.l.
- * Copyright (C) 2017 Amarula Solutions B.V.
+ * Copyright (C) 2018 Engicam S.r.l.
+ * Copyright (C) 2018 Amarula Solutions B.V.
* Author: Jagan Teki <jagan@amarulasolutions.com>
*/
/dts-v1/;
#include "imx6dl.dtsi"
-#include "imx6qdl-icore.dtsi"
+#include "imx6qdl-icore-1.5.dtsi"
/ {
model = "Engicam i.CoreM6 DualLite/Solo MIPI Starter Kit";
compatible = "engicam,imx6-icore", "fsl,imx6dl";
};
+&hdmi {
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
&usdhc3 {
status = "okay";
};
+// SPDX-License-Identifier: GPL-2.0 OR X11
/*
- * Copyright (C) 2015 Amarula Solutions B.V.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This file is distributed in the hope that it will be useful
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
*/
/dts-v1/;
/ {
model = "Engicam i.CoreM6 DualLite/Solo RQS Starter Kit";
- compatible = "engicam,imx6-icore-rqs", "fsl,imx6q";
+ compatible = "engicam,imx6-icore-rqs", "fsl,imx6dl";
};
+// SPDX-License-Identifier: GPL-2.0 OR X11
/*
* Copyright (C) 2016 Amarula Solutions B.V.
* Copyright (C) 2016 Engicam S.r.l.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This file is distributed in the hope that it will be useful
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
&can2 {
status = "okay";
};
+
+&i2c1 {
+ max11801: touchscreen@48 {
+ compatible = "maxim,max11801";
+ reg = <0x48>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Copyright 2015 Timesys Corporation.
+ * Copyright 2015 General Electric Company
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q-bx50v3.dtsi"
+
+/ {
+ model = "General Electric B450v3";
+ compatible = "ge,imx6q-b450v3", "advantech,imx6q-ba16", "fsl,imx6q";
+
+ chosen {
+ stdout-path = &uart3;
+ };
+
+ panel-lvds0 {
+ compatible = "innolux,g121x1-l03";
+ backlight = <&backlight_lvds>;
+ power-supply = <®_lvds>;
+
+ port {
+ panel_in_lvds0: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in_lvds0>;
+ };
+ };
+ };
+};
+
+&pca9539 {
+ P04 {
+ gpio-hog;
+ gpios = <4 0>;
+ output-low;
+ line-name = "PCA9539-P04";
+ };
+
+ P07 {
+ gpio-hog;
+ gpios = <7 0>;
+ output-low;
+ line-name = "PCA9539-P07";
+ };
+};
+
+&pci_root {
+ /* Intel Corporation I210 Gigabit Network Connection */
+ switch_nic: ethernet@3,0 {
+ compatible = "pci8086,1533";
+ reg = <0x00010000 0 0 0 0>;
+ };
+};
+
+&switch_ports {
+ port@0 {
+ reg = <0>;
+ label = "enacq";
+ phy-handle = <&switchphy0>;
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "eneport1";
+ phy-handle = <&switchphy1>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "enix";
+ phy-handle = <&switchphy2>;
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "enid";
+ phy-handle = <&switchphy3>;
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "cpu";
+ ethernet = <&switch_nic>;
+ phy-handle = <&switchphy4>;
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "enembc";
+
+ /* connected to Ethernet MAC of AT91RM9200 in MII mode */
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Copyright 2015 Timesys Corporation.
+ * Copyright 2015 General Electric Company
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q-bx50v3.dtsi"
+
+/ {
+ model = "General Electric B650v3";
+ compatible = "ge,imx6q-b650v3", "advantech,imx6q-ba16", "fsl,imx6q";
+
+ chosen {
+ stdout-path = &uart3;
+ };
+
+ panel-lvds0 {
+ compatible = "innolux,g121x1-l03";
+ backlight = <&backlight_lvds>;
+ power-supply = <®_lvds>;
+
+ port {
+ panel_in_lvds0: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in_lvds0>;
+ };
+ };
+ };
+};
+
+&pca9539 {
+ P07 {
+ gpio-hog;
+ gpios = <7 0>;
+ output-low;
+ line-name = "PCA9539-P07";
+ };
+};
+
+&usbphy1 {
+ fsl,tx-cal-45-dn-ohms = <55>;
+ fsl,tx-cal-45-dp-ohms = <55>;
+ fsl,tx-d-cal = <100>;
+};
+
+&pci_root {
+ /* Intel Corporation I210 Gigabit Network Connection */
+ switch_nic: ethernet@3,0 {
+ compatible = "pci8086,1533";
+ reg = <0x00010000 0 0 0 0>;
+ };
+};
+
+&switch_ports {
+ port@0 {
+ reg = <0>;
+ label = "enacq";
+ phy-handle = <&switchphy0>;
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "eneport1";
+ phy-handle = <&switchphy1>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "enix";
+ phy-handle = <&switchphy2>;
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "enid";
+ phy-handle = <&switchphy3>;
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "cpu";
+ ethernet = <&switch_nic>;
+ phy-handle = <&switchphy4>;
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "enembc";
+
+ /* connected to Ethernet MAC of AT91RM9200 in MII mode */
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Copyright 2015 Timesys Corporation.
+ * Copyright 2015 General Electric Company
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q-bx50v3.dtsi"
+
+/ {
+ model = "General Electric B850v3";
+ compatible = "ge,imx6q-b850v3", "advantech,imx6q-ba16", "fsl,imx6q";
+
+ chosen {
+ stdout-path = &uart3;
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
+ <&clks IMX6QDL_CLK_IPU1_DI0_PRE_SEL>,
+ <&clks IMX6QDL_CLK_IPU2_DI0_PRE_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
+ <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
+ <&clks IMX6QDL_CLK_PLL2_PFD2_396M>,
+ <&clks IMX6QDL_CLK_PLL2_PFD2_396M>;
+};
+
+&ldb {
+ fsl,dual-channel;
+ status = "okay";
+
+ lvds0: lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&stdp4028_in>;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ pca9547_ddc: mux@70 {
+ compatible = "nxp,pca9547";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mux2_i2c1: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0>;
+ };
+
+ mux2_i2c2: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1>;
+ };
+
+ mux2_i2c3: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+ };
+
+ mux2_i2c4: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+ };
+
+ mux2_i2c5: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4>;
+ };
+
+ mux2_i2c6: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x5>;
+ };
+
+ mux2_i2c7: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6>;
+ };
+
+ mux2_i2c8: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x7>;
+ };
+ };
+};
+
+&hdmi {
+ ddc-i2c-bus = <&mux2_i2c1>;
+};
+
+&mux1_i2c1 {
+ ads7830@4a {
+ compatible = "ti,ads7830";
+ reg = <0x4a>;
+ };
+};
+
+&mux2_i2c2 {
+ clock-frequency = <100000>;
+
+ stdp2690@72 {
+ compatible = "megachips,stdp2690-ge-b850v3-fw";
+ reg = <0x72>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ stdp2690_in: endpoint {
+ remote-endpoint = <&stdp4028_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ stdp2690_out: endpoint {
+ /* Connector for external display */
+ };
+ };
+ };
+ };
+
+ stdp4028@73 {
+ compatible = "megachips,stdp4028-ge-b850v3-fw";
+ reg = <0x73>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ stdp4028_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ stdp4028_out: endpoint {
+ remote-endpoint = <&stdp2690_in>;
+ };
+ };
+ };
+ };
+};
+
+&pca9539 {
+ P10 {
+ gpio-hog;
+ gpios = <8 0>;
+ output-low;
+ line-name = "PCA9539-P10";
+ };
+
+ P11 {
+ gpio-hog;
+ gpios = <9 0>;
+ output-low;
+ line-name = "PCA9539-P11";
+ };
+};
+
+&pci_root {
+ /* PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch */
+ bridge@1,0 {
+ compatible = "pci10b5,8605";
+ reg = <0x00010000 0 0 0 0>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+
+ bridge@2,1 {
+ compatible = "pci10b5,8605";
+ reg = <0x00020800 0 0 0 0>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+
+ /* Intel Corporation I210 Gigabit Network Connection */
+ ethernet@3,0 {
+ compatible = "pci8086,1533";
+ reg = <0x00030000 0 0 0 0>;
+ };
+ };
+
+ bridge@2,2 {
+ compatible = "pci10b5,8605";
+ reg = <0x00021000 0 0 0 0>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+
+ /* Intel Corporation I210 Gigabit Network Connection */
+ switch_nic: ethernet@4,0 {
+ compatible = "pci8086,1533";
+ reg = <0x00040000 0 0 0 0>;
+ };
+ };
+ };
+};
+
+&switch_ports {
+ port@0 {
+ reg = <0>;
+ label = "eneport1";
+ phy-handle = <&switchphy0>;
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "eneport2";
+ phy-handle = <&switchphy1>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "enix";
+ phy-handle = <&switchphy2>;
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "enid";
+ phy-handle = <&switchphy3>;
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "cpu";
+ ethernet = <&switch_nic>;
+ phy-handle = <&switchphy4>;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Support for imx6 based Advantech DMS-BA16 Qseven module
+ *
+ * Copyright 2015 Timesys Corporation.
+ * Copyright 2015 General Electric Company
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x40000000>;
+ };
+
+ backlight_lvds: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_display>;
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100 101 102 103 104 105 106 107 108 109
+ 110 111 112 113 114 115 116 117 118 119
+ 120 121 122 123 124 125 126 127 128 129
+ 130 131 132 133 134 135 136 137 138 139
+ 140 141 142 143 144 145 146 147 148 149
+ 150 151 152 153 154 155 156 157 158 159
+ 160 161 162 163 164 165 166 167 168 169
+ 170 171 172 173 174 175 176 177 178 179
+ 180 181 182 183 184 185 186 187 188 189
+ 190 191 192 193 194 195 196 197 198 199
+ 200 201 202 203 204 205 206 207 208 209
+ 210 211 212 213 214 215 216 217 218 219
+ 220 221 222 223 224 225 226 227 228 229
+ 230 231 232 233 234 235 236 237 238 239
+ 240 241 242 243 244 245 246 247 248 249
+ 250 251 252 253 254 255>;
+ default-brightness-level = <255>;
+ enable-gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "1P8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_lvds: regulator-lvds {
+ compatible = "regulator-fixed";
+ regulator-name = "lvds_ppen";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_h1_vbus: regulator-usbh1vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_usb_otg_vbus: regulator-usbotgvbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash: n25q032@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+
+ partition@0 {
+ label = "U-Boot";
+ reg = <0x0 0xc0000>;
+ };
+
+ partition@c0000 {
+ label = "env";
+ reg = <0xc0000 0x10000>;
+ };
+
+ partition@d0000 {
+ label = "spare";
+ reg = <0xd0000 0x320000>;
+ };
+
+ partition@3f0000 {
+ label = "mfg";
+ reg = <0x3f0000 0x10000>;
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ pmic@58 {
+ compatible = "dlg,da9063";
+ reg = <0x58>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio7>;
+ interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+
+ onkey {
+ compatible = "dlg,da9063-onkey";
+ };
+
+ regulators {
+ vdd_bcore1: bcore1 {
+ regulator-min-microvolt = <1420000>;
+ regulator-max-microvolt = <1420000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_bcore2: bcore2 {
+ regulator-min-microvolt = <1420000>;
+ regulator-max-microvolt = <1420000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_bpro: bpro {
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_bmem: bmem {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_bio: bio {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_bperi: bperi {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_ldo1: ldo1 {
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1860000>;
+ };
+
+ vdd_ldo2: ldo2 {
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1860000>;
+ };
+
+ vdd_ldo3: ldo3 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <3440000>;
+ };
+
+ vdd_ldo4: ldo4 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <3440000>;
+ };
+
+ vdd_ldo5: ldo5 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ vdd_ldo6: ldo6 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ vdd_ldo7: ldo7 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ vdd_ldo8: ldo8 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ vdd_ldo9: ldo9 {
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ vdd_ldo10: ldo10 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ vdd_ldo11: ldo11 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+
+ rtc@32 {
+ compatible = "epson,rx8010";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc>;
+ reg = <0x32>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
+ fsl,tx-swing-full = <103>;
+ fsl,tx-swing-low = <103>;
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "disabled";
+};
+
+&sata {
+ status = "okay";
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbh1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbhub>;
+ vbus-supply = <®_usb_h1_vbus>;
+ reset-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3 &pinctrl_usdhc3_reset>;
+ bus-width = <8>;
+ vmmc-supply = <&vdd_bperi>;
+ non-removable;
+ keep-power-in-suspend;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
+ MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x130b0
+ MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
+ MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
+ >;
+ };
+
+ pinctrl_display: dispgrp {
+ fsl,pins = <
+ /* BLEN_OUT */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ /* LVDS_PPEN_OUT */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* SPI1 CS */
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi5: ecspi5grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT0__ECSPI5_MISO 0x1b0b0
+ MX6QDL_PAD_SD1_CMD__ECSPI5_MOSI 0x1b0b0
+ MX6QDL_PAD_SD1_CLK__ECSPI5_SCLK 0x1b0b0
+ MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ /* FEC Reset */
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0
+ /* AR8033 Interrupt */
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
+ >;
+ };
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* GPIO 0-7 */
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+ MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
+ MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0
+ MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x1b0b0
+ MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x1b0b0
+ MX6QDL_PAD_NANDF_D7__GPIO2_IO07 0x1b0b0
+ /* SUS_S3_OUT to CPLD */
+ MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ /* PCIe Reset */
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ /* PCIe Wake */
+ MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x1b0b0
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ /* PMIC Interrupt */
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_rtc: rtcgrp {
+ fsl,pins = <
+ /* RTC_INT */
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbhub: usbhubgrp {
+ fsl,pins = <
+ /* HUB_RESET */
+ MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+ /* uSDHC2 CD */
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3_reset: usdhc3grp-reset {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x170F9
+ >;
+ };
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x17059
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+ /* uSDHC4 CD */
+ MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x1b0b0
+ /* uSDHC4 SDIO PWR */
+ MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x1b0b0
+ /* uSDHC4 SDIO WP */
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0
+ /* uSDHC4 SDIO LED */
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x1b0b0
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__WDOG1_B 0x1b0b0
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Copyright 2019 Collabora Ltd
+ * Copyright 2019 General Electric Company
+ */
+
+/ {
+ wdt-reboot {
+ compatible = "wdt-reboot";
+ wdt = <&wdog1>;
+ };
+};
-/* SPDX-License-Identifier: GPL-2.0+ OR X11 */
+// SPDX-License-Identifier: GPL-2.0+ OR X11
/*
* Copyright 2015 Timesys Corporation.
* Copyright 2018 General Electric Company
/dts-v1/;
-#include "imx6q.dtsi"
-#include <dt-bindings/gpio/gpio.h>
+#include "imx6q-bx50v3.dtsi"
/ {
model = "General Electric Bx50v3";
compatible = "ge,imx6q-bx50v3", "advantech,imx6q-ba16", "fsl,imx6q";
-};
-
-&iomuxc {
- pinctrl-names = "default";
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
- MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
- MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
- /* SPI1 CS */
- MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
- >;
- };
-
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <
- MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
- MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
- MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
- MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
- MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
- MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
- MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
- MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
- MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
- MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
- >;
- };
-
- pinctrl_usdhc3_reset: usdhc3grp-reset {
- fsl,pins = <
- MX6QDL_PAD_SD3_RST__SD3_RESET 0x170F9
- >;
- };
-};
-
-&usdhc1 {
- status = "disabled";
-};
-
-&usdhc2 {
- status = "disabled";
-};
-
-/* eMMC */
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3 &pinctrl_usdhc3_reset>;
- bus-width = <8>;
- non-removable;
- keep-power-in-suspend;
- status = "okay";
-};
-
-&usdhc4 {
- status = "disabled";
-};
-
-/* SPI NOR */
-&ecspi1 {
- cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
- flash: n25q032@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <20000000>;
- reg = <0>;
+ chosen {
+ stdout-path = &uart3;
};
};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Copyright 2015 Timesys Corporation.
+ * Copyright 2015 General Electric Company
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "imx6q-ba16.dtsi"
+#include "imx6q-bx50v3-uboot.dtsi"
+
+/ {
+ mclk: clock-mclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <22000000>;
+ };
+
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+ status = "okay";
+ };
+
+ reg_wl18xx_vmmc: regulator-wl18xx {
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1807";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pca9539 3 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
+ reg_wlan: regulator-wlan {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V_wlan";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio6 14 GPIO_ACTIVE_HIGH>;
+ };
+
+ sound {
+ compatible = "fsl,imx6q-ba16-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx6q-ba16-sgtl5000";
+ ssi-controller = <&ssi1>;
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <1>;
+ mux-ext-port = <4>;
+ };
+
+ aliases {
+ mdio-gpio0 = &mdio0;
+ };
+
+ mdio0: mdio-gpio {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>, /* mdc */
+ <&gpio2 7 GPIO_ACTIVE_HIGH>; /* mdio */
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch@0 {
+ compatible = "marvell,mv88e6085"; /* 88e6240*/
+ reg = <0>;
+
+ switch_ports: ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switchphy0: switchphy@0 {
+ reg = <0>;
+ };
+
+ switchphy1: switchphy@1 {
+ reg = <1>;
+ };
+
+ switchphy2: switchphy@2 {
+ reg = <2>;
+ };
+
+ switchphy3: switchphy@3 {
+ reg = <3>;
+ };
+
+ switchphy4: switchphy@4 {
+ reg = <4>;
+ };
+ };
+ };
+ };
+};
+
+&ecspi5 {
+ cs-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi5>;
+ status = "okay";
+
+ m25_eeprom: m25p80@0 {
+ compatible = "atmel,at25";
+ spi-max-frequency = <10000000>;
+ size = <0x8000>;
+ pagesize = <64>;
+ reg = <0>;
+ address-width = <16>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ sda-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;
+
+ pca9547: mux@70 {
+ compatible = "nxp,pca9547";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mux1_i2c1: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0>;
+
+ ads7830: ads7830@48 {
+ compatible = "ti,ads7830";
+ reg = <0x48>;
+ };
+
+ mma8453: mma8453@1c {
+ compatible = "fsl,mma8453";
+ reg = <0x1c>;
+ };
+ };
+
+ mux1_i2c2: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1>;
+
+ eeprom: eeprom@50 {
+ compatible = "atmel,24c08";
+ reg = <0x50>;
+ };
+
+ mpl3115: mpl3115@60 {
+ compatible = "fsl,mpl3115";
+ reg = <0x60>;
+ };
+ };
+
+ mux1_i2c3: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+ };
+
+ mux1_i2c4: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&mclk>;
+ VDDA-supply = <®_1p8v>;
+ VDDIO-supply = <®_3p3v>;
+ };
+ };
+
+ mux1_i2c5: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4>;
+
+ pca9539: pca9539@74 {
+ compatible = "nxp,pca9539";
+ reg = <0x74>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ interrupt-parent = <&gpio2>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+ P12 {
+ gpio-hog;
+ gpios = <10 0>;
+ output-low;
+ line-name = "PCA9539-P12";
+ };
+
+ P13 {
+ gpio-hog;
+ gpios = <11 0>;
+ output-low;
+ line-name = "PCA9539-P13";
+ };
+
+ P14 {
+ gpio-hog;
+ gpios = <12 0>;
+ output-low;
+ line-name = "PCA9539-P14";
+ };
+
+ P15 {
+ gpio-hog;
+ gpios = <13 0>;
+ output-low;
+ line-name = "PCA9539-P15";
+ };
+
+ P16 {
+ gpio-hog;
+ gpios = <14 0>;
+ output-low;
+ line-name = "PCA9539-P16";
+ };
+
+ P17 {
+ gpio-hog;
+ gpios = <15 0>;
+ output-low;
+ line-name = "PCA9539-P17";
+ };
+ };
+ };
+
+ mux1_i2c6: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x5>;
+ };
+
+ mux1_i2c7: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6>;
+ };
+
+ mux1_i2c8: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x7>;
+ };
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ sda-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+};
+
+&i2c3 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ sda-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+};
+
+&iomuxc {
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x1b0b0
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0
+ >;
+ };
+};
+
+&pmu {
+ secure-reg-access;
+};
+
+&usdhc2 {
+ status = "disabled";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <4>;
+ vmmc-supply = <®_wl18xx_vmmc>;
+ no-1-8-v;
+ non-removable;
+ wakeup-source;
+ keep-power-in-suspend;
+ cap-power-off-card;
+ max-frequency = <25000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1837";
+ reg = <2>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
+ tcxo-clock-frequency = <26000000>;
+ };
+};
+
+&pcie {
+ /* Synopsys, Inc. Device */
+ pci_root: root@0,0 {
+ compatible = "pci16c3,abcd";
+ reg = <0x00000000 0 0 0 0>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ };
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-sr-som-emmc.dtsi"
+#include "imx6qdl-cubox-i.dtsi"
+
+/ {
+ model = "SolidRun Cubox-i Dual/Quad (1.5som+emmc)";
+ compatible = "solidrun,cubox-i/q", "fsl,imx6q";
+};
+
+&sata {
+ status = "okay";
+ fsl,transmit-level-mV = <1104>;
+ fsl,transmit-boost-mdB = <0>;
+ fsl,transmit-atten-16ths = <9>;
+ fsl,no-spread-spectrum;
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-cubox-i.dtsi"
+
+/ {
+ model = "SolidRun Cubox-i Dual/Quad (1.5som)";
+ compatible = "solidrun,cubox-i/q", "fsl,imx6q";
+};
+
+&sata {
+ status = "okay";
+ fsl,transmit-level-mV = <1104>;
+ fsl,transmit-boost-mdB = <0>;
+ fsl,transmit-atten-16ths = <9>;
+ fsl,no-spread-spectrum;
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-brcm.dtsi"
+#include "imx6qdl-cubox-i.dtsi"
+
+/ {
+ model = "SolidRun Cubox-i Dual/Quad";
+ compatible = "solidrun,cubox-i/q", "fsl,imx6q";
+};
+
+&sata {
+ status = "okay";
+ fsl,transmit-level-mV = <1104>;
+ fsl,transmit-boost-mdB = <0>;
+ fsl,transmit-atten-16ths = <9>;
+ fsl,no-spread-spectrum;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+)
+/*
+ * Copyright (C) 2019 Claudius Heine <ch@denx.de>
+ */
+
+/ {
+ wdt-reboot {
+ compatible = "wdt-reboot";
+ wdt = <&wdog1>;
+ };
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 Rabeeh Khoury (rabeeh@solid-run.com)
+ * Based on dt work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-sr-som-emmc.dtsi"
+#include "imx6qdl-hummingboard.dtsi"
+
+/ {
+ model = "SolidRun HummingBoard Dual/Quad (1.5som+emmc)";
+ compatible = "solidrun,hummingboard/q", "fsl,imx6q";
+};
+
+&sata {
+ status = "okay";
+ fsl,transmit-level-mV = <1025>;
+ fsl,transmit-boost-mdB = <3330>;
+ fsl,transmit-atten-16ths = <9>;
+ fsl,receive-eq-mdB = <3000>;
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 Rabeeh Khoury (rabeeh@solid-run.com)
+ * Based on dt work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-hummingboard.dtsi"
+
+/ {
+ model = "SolidRun HummingBoard Dual/Quad (1.5som)";
+ compatible = "solidrun,hummingboard/q", "fsl,imx6q";
+};
+
+&sata {
+ status = "okay";
+ fsl,transmit-level-mV = <1025>;
+ fsl,transmit-boost-mdB = <3330>;
+ fsl,transmit-atten-16ths = <9>;
+ fsl,receive-eq-mdB = <3000>;
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 Rabeeh Khoury (rabeeh@solid-run.com)
+ * Based on dt work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-brcm.dtsi"
+#include "imx6qdl-hummingboard.dtsi"
+
+/ {
+ model = "SolidRun HummingBoard Dual/Quad";
+ compatible = "solidrun,hummingboard/q", "fsl,imx6q";
+};
+
+&sata {
+ status = "okay";
+ fsl,transmit-level-mV = <1025>;
+ fsl,transmit-boost-mdB = <3330>;
+ fsl,transmit-atten-16ths = <9>;
+ fsl,receive-eq-mdB = <3000>;
+};
--- /dev/null
+#include "imx6qdl-hummingboard2-emmc-som-v15-u-boot.dtsi"
--- /dev/null
+/*
+ * Device Tree file for SolidRun HummingBoard2
+ * Copyright (C) 2015 Rabeeh Khoury <rabeeh@solid-run.com>
+ * Based on work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-emmc.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-hummingboard2.dtsi"
+
+/ {
+ model = "SolidRun HummingBoard2 Dual/Quad (1.5som+emmc)";
+ compatible = "solidrun,hummingboard2/q", "fsl,imx6q";
+};
+
+&sata {
+ status = "okay";
+ fsl,transmit-level-mV = <1104>;
+ fsl,transmit-boost-mdB = <0>;
+ fsl,transmit-atten-16ths = <9>;
+ fsl,no-spread-spectrum;
+};
--- /dev/null
+/*
+ * Device Tree file for SolidRun HummingBoard2
+ * Copyright (C) 2015 Rabeeh Khoury <rabeeh@solid-run.com>
+ * Based on work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-hummingboard2.dtsi"
+
+/ {
+ model = "SolidRun HummingBoard2 Dual/Quad (1.5som)";
+ compatible = "solidrun,hummingboard2/q", "fsl,imx6q";
+};
+
+&sata {
+ status = "okay";
+ fsl,transmit-level-mV = <1104>;
+ fsl,transmit-boost-mdB = <0>;
+ fsl,transmit-atten-16ths = <9>;
+ fsl,no-spread-spectrum;
+};
--- /dev/null
+/*
+ * Copyright (C) 2015 Rabeeh Khoury <rabeeh@solid-run.com>
+ * Based on dt work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-brcm.dtsi"
+#include "imx6qdl-hummingboard2.dtsi"
+#include "imx6qdl-hummingboard2-emmc.dtsi"
+
+/ {
+ model = "SolidRun HummingBoard2 Dual/Quad";
+ compatible = "solidrun,hummingboard2/q", "fsl,imx6q";
+};
+
+&sata {
+ status = "okay";
+ fsl,transmit-level-mV = <1104>;
+ fsl,transmit-boost-mdB = <0>;
+ fsl,transmit-atten-16ths = <9>;
+ fsl,no-spread-spectrum;
+};
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// SPDX-License-Identifier: GPL-2.0 OR X11
/*
* Copyright (C) 2017 Engicam S.r.l.
* Copyright (C) 2017 Amarula Solutions B.V.
/dts-v1/;
#include "imx6q.dtsi"
-#include "imx6qdl-icore.dtsi"
+#include "imx6qdl-icore-1.5.dtsi"
/ {
- model = "Engicam i.CoreM6 Quad/Dual MIPI Starter Kit";
+ model = "Engicam i.CoreM6 1.5 Quad/Dual MIPI Starter Kit";
compatible = "engicam,imx6-icore", "fsl,imx6q";
};
+&hdmi {
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&mipi_csi {
+ status = "okay";
+};
+
+&ov5640 {
+ status = "okay";
+};
+
&usdhc3 {
status = "okay";
};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-icore.dtsi"
+
+/ {
+ model = "Engicam i.CoreM6 Quad/Dual OpenFrame Capacitive touch 10.1 Kit";
+ compatible = "engicam,imx6-icore", "fsl,imx6q";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <60000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <40>;
+ hfront-porch = <40>;
+ vback-porch = <10>;
+ vfront-porch = <3>;
+ hsync-len = <80>;
+ vsync-len = <10>;
+ };
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-icore.dtsi"
+
+/ {
+ model = "Engicam i.CoreM6 Quad/Dual OpenFrame Capacitive touch 12 Kit";
+ compatible = "engicam,imx6-icore", "fsl,imx6q";
+
+ panel {
+ compatible = "koe,tx31d200vm0baa";
+ backlight = <&backlight_lvds>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ reg = <0>;
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (C) 2015 Amarula Solutions B.V.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This file is distributed in the hope that it will be useful
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
+ * Copyright (C) 2015 Engicam S.r.l.
*/
/dts-v1/;
model = "Engicam i.CoreM6 Quad/Dual RQS Starter Kit";
compatible = "engicam,imx6-icore-rqs", "fsl,imx6q";
};
+
+&sata {
+ status = "okay";
+};
+// SPDX-License-Identifier: GPL-2.0 OR X11
/*
* Copyright (C) 2016 Amarula Solutions B.V.
* Copyright (C) 2016 Engicam S.r.l.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This file is distributed in the hope that it will be useful
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
&can2 {
status = "okay";
};
+
+&i2c1 {
+ max11801: touchscreen@48 {
+ compatible = "maxim,max11801";
+ reg = <0x48>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <60000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <30>;
+ hfront-porch = <30>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <64>;
+ vsync-len = <20>;
+ };
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2 board
+ * parts common to all versions
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ *
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx6qdl-clock.h>
+
+/ {
+ aliases {
+ eeprom0 = &i2c_eeprom0;
+ pmic0 = &i2c_pmic0;
+ };
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x40000000>;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ enable-gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_2p5v: regulator-2p5v {
+ compatible = "regulator-fixed";
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usbh1_vbus: regulator-usbh1-vbus {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_aristainetos2_usbh1_vbus>;
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_usbotg_vbus: regulator-usbotg-vbus {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_aristainetos2_usbotg_vbus>;
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH &gpio2 27 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ i2c_pmic0: pmic@58 {
+ compatible = "dlg,da9063";
+ /* the pmic uses addr 0x58 and 0x59 */
+ reg = <0x58>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <04 0x8>;
+
+ regulators {
+ bcore1 {
+ regulator-name = "bcore1";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ bcore2 {
+ regulator-name = "bcore2";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ bpro {
+ regulator-name = "bpro";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ bprob {
+ regulator-name = "bprob";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ bperi {
+ regulator-name = "bperi";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ bmem {
+ regulator-name = "bmem";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo2 {
+ regulator-name = "ldo2";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo3 {
+ regulator-name = "ldo3";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo4 {
+ regulator-name = "ldo4";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo5 {
+ regulator-name = "ldo5";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo6 {
+ regulator-name = "ldo6";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo7 {
+ regulator-name = "ldo7";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo8 {
+ regulator-name = "ldo8";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo9 {
+ regulator-name = "ldo9";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo10 {
+ regulator-name = "ldo10";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo11 {
+ regulator-name = "ldo11";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ bio {
+ regulator-name = "bio";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+ };
+
+ tmp103: tmp103@71 {
+ compatible = "ti,tmp103";
+ reg = <0x71>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ expander: tca6416@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ #gpio-cells = <2>;
+ gpio-controller;
+
+ env_reset {
+ gpio-hog;
+ input;
+ gpios = <6 GPIO_ACTIVE_LOW>;
+ };
+ boot_rescue {
+ gpio-hog;
+ input;
+ gpios = <7 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ rtc@68 {
+ compatible = "st,m41t11";
+ reg = <0x68>;
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+
+ i2c_eeprom0: eeprom@50{
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ pagesize = <32>;
+ };
+
+ i2c_eeprom1: eeprom@57{
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ pagesize = <32>;
+ };
+};
+
+&gpio6 {
+ spi_bus_ena {
+ gpio-hog;
+ output-high;
+ gpios = <6 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&gpio7 {
+ bootsel0 {
+ gpio-hog;
+ input;
+ gpios = <6 GPIO_ACTIVE_HIGH>;
+ };
+ bootsel1 {
+ gpio-hog;
+ input;
+ gpios = <7 GPIO_ACTIVE_HIGH>;
+ };
+ bootsel2 {
+ gpio-hog;
+ input;
+ gpios = <1 GPIO_ACTIVE_HIGH>;
+ };
+
+ soft_reset {
+ gpio-hog;
+ output-high;
+ gpios = <13 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ txd0-skew-ps = <0>;
+ txd1-skew-ps = <0>;
+ txd2-skew-ps = <0>;
+ txd3-skew-ps = <0>;
+ status = "okay";
+};
+
+&pcie {
+ reset-gpio = <&gpio2 16 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usbh1_vbus>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usbotg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ dr_mode = "host"; /* fixed configuration, ID pin not checked */
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio>;
+
+ pinctrl_audmux: audmux {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x100b1 /* SS0# */
+ MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x100b1 /* SS1# */
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x400100b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ /* make sure pin is GPIO and not ENET_REF_CLK */
+ MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x1a0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__I2C4_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_8__I2C4_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
+ /* backlight enable */
+ MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D20__UART1_RTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D19__UART1_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_aristainetos2_usbh1_vbus: aristainetos-usbh1-vbus {
+ fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x400130b0>;
+ };
+
+ pinctrl_aristainetos2_usbotg_vbus: aristainetos-usbotg-vbus {
+ fsl,pins = <MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x400130b0>;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ */
+
+/ {
+ chosen {
+ u-boot,dm-pre-reloc;
+ stdout-path = &uart2;
+ };
+
+ wdt-reboot {
+ compatible = "wdt-reboot";
+ wdt = <&wdog1>;
+ };
+};
+
+&uart2 {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_gpio {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_uart2 {
+ u-boot,dm-pre-reloc;
+};
+
+&aips2 {
+ u-boot,dm-pre-reloc;
+};
+
+&backlight {
+ pwms = <&pwm1 0 300000>;
+ default-brightness-level = <2>;
+};
+
+/*
+ * allow switching write protect pin by gpio,
+ * because "pinctrl-assert-gpios" from &ecspi1 isn't handled by u-boot
+ */
+&gpio2 {
+ u-boot,dm-pre-reloc;
+
+ wp_spi_nor {
+ gpio-hog;
+ output-high;
+ gpios = <15 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&iomuxc {
+ pinctrl-0 = <&pinctrl_gpio &pinctrl_gpio_fix>;
+ u-boot,dm-pre-reloc;
+
+ pinctrl_gpio_fix: gpiofixgrp {
+ /*
+ * usdhc2 has a levelshifter on the carrier board Rev. DV1,
+ * that will automatically detect the driving direction.
+ * During initialisation this isn't working correctly,
+ * which causes DAT3 to be driven low towards the SD-card.
+ * This causes a SD-card enetring the SPI-Mode
+ * and therefore getting inaccessible until next power cycle.
+ * As workaround we drive the DAT3 line as GPIO and set it high.
+ * This makes usdhc2 unusable in u-boot, but works for the
+ * initialisation in Linux
+ */
+ fsl,pins = <
+ MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x20000
+ >;
+ };
+};
+
+&gpio1 {
+ usdhc_fix {
+ gpio-hog;
+ output-high;
+ gpios = <12 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&gpio3 {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio5 {
+ u-boot,dm-pre-reloc;
+};
+
+&ecspi4 {
+ u-boot,dm-pre-reloc;
+};
+
+&flash {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_ecspi4 {
+ u-boot,dm-pre-reloc;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2 board
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ *
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx6qdl-clock.h>
+
+#include "imx6qdl-aristainetos2-common.dtsi"
+
+/ {
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio>;
+
+ LED_blue {
+ label = "led_blue";
+ gpios = <&gpio2 29 GPIO_ACTIVE_LOW>;
+ };
+
+ LED_green {
+ label = "led_green";
+ gpios = <&gpio5 4 GPIO_ACTIVE_LOW>;
+ };
+
+ LED_red {
+ label = "led_red";
+ gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+ };
+
+ LED_yellow {
+ label = "led_yellow";
+ gpios = <&gpio6 16 GPIO_ACTIVE_LOW>;
+ };
+
+ LED_ena {
+ label = "led_ena";
+ gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <3>;
+ cs-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH
+ &gpio4 10 GPIO_ACTIVE_HIGH
+ &gpio4 11 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+};
+
+&ecspi4 {
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH &gpio5 2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi4>;
+ status = "okay";
+ pinctrl-assert-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+
+ flash: m25p80@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q128a11", "jedec,spi-nor";
+ spi-max-frequency = <20000000>;
+ reg = <1>;
+ };
+};
+
+&gpio7 {
+ sd2_driver_ena {
+ gpio-hog;
+ output-high;
+ gpios = <8 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ cd-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x100b1 /* SS0# */
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x100b1 /* SS1# */
+ MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x100b1 /* SS2# */
+ >;
+ };
+
+ pinctrl_ecspi4: ecspi4grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
+ MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x100b1 /* SS0# */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b1 /* SS1# */
+ MX6QDL_PAD_SD4_DAT7__GPIO2_IO15 0x4001b0b0 /* WP pin */
+ >;
+ };
+
+ pinctrl_gpio: gpiogrp {
+ fsl,pins = <
+ /* led enable */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x4001b0b0
+ /* LCD power enable */
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x4001b0b0
+ /* led yellow */
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x4001b0b0
+ /* led red */
+ MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x4001b0b0
+ /* led green */
+ MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x4001b0b0
+ /* led blue */
+ MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x4001b0b0
+ /* Profibus IRQ */
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0
+ /* FPGA IRQ currently unused*/
+ MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x1b0b0
+ /* Display reset because of clock failure */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x4001b0b0
+ /* spi bus #2 SS driver enable */
+ MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x4001b0b0
+ /* RST_LOC# PHY reset input (has pull-down!)*/
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x4001b0b0
+ /* USB_OTG_ID = GPIO1_24*/
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x4001b0b0
+ /* Touchscreen IRQ */
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ /* PCIe reset */
+ MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x4001b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpmi-nand {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x1b0b0
+ MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX 0x1b0b0
+ MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ /* SD1 card detect input */
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0
+ /* SD1 write protect input */
+ MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x71
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x71
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x71
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x71
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x71
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x71
+ /* SD2 level shifter output enable */
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x4001b0b0
+ /* SD2 card detect input */
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
+ /* SD2 write protect input */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ or X11
+/*
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ */
+
+/ {
+ chosen {
+ u-boot,dm-pre-reloc;
+ stdout-path = &uart2;
+ };
+
+ wdt-reboot {
+ compatible = "wdt-reboot";
+ wdt = <&wdog1>;
+ };
+};
+
+&uart2 {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_gpio {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_uart2 {
+ u-boot,dm-pre-reloc;
+};
+
+&iomuxc {
+ u-boot,dm-pre-reloc;
+};
+
+&aips2 {
+ u-boot,dm-pre-reloc;
+};
+
+&backlight {
+ pwms = <&pwm1 0 300000>;
+ default-brightness-level = <2>;
+};
+
+/*
+ * allow switching write protect / reset pin by gpio,
+ * because "pinctrl-assert-gpios" from &ecspi1 isn't handled by u-boot
+ */
+&gpio2 {
+ u-boot,dm-pre-reloc;
+
+ wp_spi_nor {
+ gpio-hog;
+ output-high;
+ gpios = <15 GPIO_ACTIVE_HIGH>;
+ };
+
+ reset_spi_nor {
+ gpio-hog;
+ output-high;
+ gpios = <28 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&gpio4 {
+ u-boot,dm-pre-reloc;
+};
+
+&ecspi1 {
+ u-boot,dm-pre-reloc;
+};
+
+&flash {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_ecspi1 {
+ u-boot,dm-pre-reloc;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2b board
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ *
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx6qdl-clock.h>
+
+#include "imx6qdl-aristainetos2-common.dtsi"
+
+/ {
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio>;
+
+ LED_blue {
+ label = "led_blue";
+ gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_green {
+ label = "led_green";
+ gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_red {
+ label = "led_red";
+ gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_yellow {
+ label = "led_yellow";
+ gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_ena {
+ label = "led_ena";
+ gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <3>;
+ cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH
+ &gpio4 10 GPIO_ACTIVE_HIGH
+ &gpio4 11 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+ pinctrl-assert-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
+ pinctrl-assert-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q128a11", "jedec,spi-nor";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+};
+
+&ecspi4 {
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH &gpio5 2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi4>;
+ status = "okay";
+};
+
+&i2c1 {
+ tpm@20 {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ };
+};
+
+&gpio7 {
+ sd2_driver_ena {
+ gpio-hog;
+ output-high;
+ gpios = <8 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio4 20 GPIO_ACTIVE_HIGH>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ /*
+ * comment out this line to make the WiFi Eval-Module work in
+ * SD-Slot2, and add line:
+ * broken-cd;
+ * causes 6% CPU load if no WiFi module installed (polling)
+ */
+ cd-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* SS0# */
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x100b1
+ /* SS1# */
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x100b1
+ /* SS2# */
+ MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x100b1
+ /* WP pin NOR Flash */
+ MX6QDL_PAD_SD4_DAT7__GPIO2_IO15 0x4001b0b0
+ /* Flash nReset */
+ MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x4001b0b0
+ >;
+ };
+
+ pinctrl_ecspi4: ecspi4grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
+ MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x100b1 /* SS0# */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b1 /* SS1# */
+ >;
+ };
+
+ pinctrl_gpio: gpiogrp {
+ fsl,pins = <
+ /* led enable */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x4001b0b0
+ /* LCD power enable */
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x4001b0b0
+ /* led yellow */
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x4001b0b0
+ /* led red */
+ MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x4001b0b0
+ /* led green */
+ MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x4001b0b0
+ /* led blue */
+ MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x4001b0b0
+ /* Profibus IRQ */
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0
+ /* FPGA IRQ currently unused*/
+ MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x1b0b0
+ /* Display reset because of clock failure */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x4001b0b0
+ /* spi bus #2 SS driver enable */
+ MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x4001b0b0
+ /* RST_LOC# PHY reset input (has pull-down!)*/
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x4001b0b0
+ /* Touchscreen IRQ */
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ /* PCIe reset */
+ MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x4001b0b0
+ /* make sure pin is GPIO and not ENET_REF_CLK */
+ MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001a0b0
+ /* SD2 level shifter output enable / SD2 Reset# */
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x4001b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpmi-nand {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x1b0b0
+ MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX 0x1b0b0
+ MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ /* SD1 card detect input */
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0
+ /* SD1 write protect input */
+ MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x71
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x71
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x71
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x71
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x71
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x71
+ /* SD2 card detect input */
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
+ /* SD2 write protect input */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ or X11
+/*
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ */
+
+/ {
+ chosen {
+ u-boot,dm-pre-reloc;
+ stdout-path = &uart1;
+ };
+
+ wdt-reboot {
+ compatible = "wdt-reboot";
+ wdt = <&wdog1>;
+ };
+};
+
+&uart1 {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_gpio {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_uart1 {
+ u-boot,dm-pre-reloc;
+};
+
+&iomuxc {
+ u-boot,dm-pre-reloc;
+};
+
+&aips1 {
+ u-boot,dm-pre-reloc;
+};
+
+&backlight {
+ pwms = <&pwm1 0 300000>;
+ default-brightness-level = <2>;
+};
+
+/*
+ * allow switching write protect / reset pin by gpio,
+ * because "pinctrl-assert-gpios" from &ecspi1 isn't handled by u-boot
+ */
+&gpio2 {
+ u-boot,dm-pre-reloc;
+
+ wp_spi_nor {
+ gpio-hog;
+ output-high;
+ gpios = <15 GPIO_ACTIVE_HIGH>;
+ };
+
+ reset_spi_nor {
+ gpio-hog;
+ output-high;
+ gpios = <28 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&gpio4 {
+ u-boot,dm-pre-reloc;
+};
+
+&ecspi1 {
+ u-boot,dm-pre-reloc;
+};
+
+&flash {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_ecspi1 {
+ u-boot,dm-pre-reloc;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2b-csl board
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ *
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx6qdl-clock.h>
+
+#include "imx6qdl-aristainetos2-common.dtsi"
+
+/ {
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio>;
+
+ LED_blue {
+ label = "led_blue";
+ gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_green {
+ label = "led_green";
+ gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_red {
+ label = "led_red";
+ gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_yellow {
+ label = "led_yellow";
+ gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_blue_2 {
+ label = "led_blue2";
+ gpios = <&expander 15 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ LED_green_2 {
+ label = "led_green2";
+ gpios = <&expander 14 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ LED_red_2 {
+ label = "led_red2";
+ gpios = <&expander 12 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ LED_yellow_2 {
+ label = "led_yellow2";
+ gpios = <&expander 13 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ LED_ena {
+ label = "led_ena";
+ gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <3>;
+ cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH
+ &gpio4 10 GPIO_ACTIVE_HIGH
+ &gpio4 11 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+ pinctrl-assert-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
+ pinctrl-assert-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q128a11", "jedec,spi-nor";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+};
+
+&ecspi4 {
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH &gpio5 2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi4>;
+ status = "okay";
+};
+
+&i2c1 {
+ tpm@20 {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ };
+};
+
+&gpio7 {
+ wlan_reset {
+ gpio-hog;
+ output-high;
+ gpios = <8 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* SS0# */
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x100b1
+ /* SS1# */
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x100b1
+ /* SS2# */
+ MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x100b1
+ /* WP pin NOR Flash */
+ MX6QDL_PAD_SD4_DAT7__GPIO2_IO15 0x4001b0b0
+ /* Flash nReset */
+ MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x4001b0b0
+ >;
+ };
+
+ pinctrl_ecspi4: ecspi4grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
+ MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x100b1 /* SS0# */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b1 /* SS1# */
+ >;
+ };
+
+ pinctrl_gpio: gpiogrp {
+ fsl,pins = <
+ /* led enable */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x4001b0b0
+ /* LCD power enable */
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x4001b0b0
+ /* led yellow */
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x4001b0b0
+ /* led red */
+ MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x4001b0b0
+ /* led green */
+ MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x4001b0b0
+ /* led blue */
+ MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x4001b0b0
+ /* Profibus IRQ */
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0
+ /* FPGA IRQ currently unused*/
+ MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x1b0b0
+ /* Display reset because of clock failure */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x4001b0b0
+ /* spi bus #2 SS driver enable */
+ MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x4001b0b0
+ /* RST_LOC# PHY reset input (has pull-down!)*/
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x4001b0b0
+ /* Touchscreen IRQ */
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ /* PCIe reset */
+ MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x4001b0b0
+ /* make sure pin is GPIO and not ENET_REF_CLK */
+ MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001a0b0
+ /* WLAN Module Reset# */
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x4001b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpmi-nand {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ /* SD1 card detect input */
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x71
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x71
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x71
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x71
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x71
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x71
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ or X11
+/*
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ */
+
+/ {
+ chosen {
+ u-boot,dm-pre-reloc;
+ stdout-path = &uart2;
+ };
+
+ wdt-reboot {
+ compatible = "wdt-reboot";
+ wdt = <&wdog1>;
+ };
+};
+
+&uart2 {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_gpio {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_uart2 {
+ u-boot,dm-pre-reloc;
+};
+
+&iomuxc {
+ u-boot,dm-pre-reloc;
+};
+
+&aips2 {
+ u-boot,dm-pre-reloc;
+};
+
+&backlight {
+ pwms = <&pwm1 0 300000>;
+ default-brightness-level = <2>;
+};
+
+/*
+ * allow switching write protect / reset pin by gpio,
+ * because "pinctrl-assert-gpios" from &ecspi1 isn't handled by u-boot
+ */
+&gpio2 {
+ u-boot,dm-pre-reloc;
+
+ wp_spi_nor {
+ gpio-hog;
+ output-high;
+ gpios = <15 GPIO_ACTIVE_HIGH>;
+ };
+
+ reset_spi_nor {
+ gpio-hog;
+ output-high;
+ gpios = <28 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&gpio4 {
+ u-boot,dm-pre-reloc;
+};
+
+&ecspi1 {
+ u-boot,dm-pre-reloc;
+};
+
+&flash {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_ecspi1 {
+ u-boot,dm-pre-reloc;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2c board
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ *
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx6qdl-clock.h>
+
+#include "imx6qdl-aristainetos2-common.dtsi"
+
+/ {
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio>;
+
+ LED_blue {
+ label = "led_blue";
+ gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_green {
+ label = "led_green";
+ gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_red {
+ label = "led_red";
+ gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_yellow {
+ label = "led_yellow";
+ gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_ena {
+ label = "led_ena";
+ gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <3>;
+ cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH
+ &gpio4 10 GPIO_ACTIVE_HIGH
+ &gpio4 11 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+ pinctrl-assert-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
+ pinctrl-assert-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q128a11", "jedec,spi-nor";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+};
+
+&ecspi4 {
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH &gpio5 2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi4>;
+ status = "okay";
+};
+
+&i2c1 {
+ tpm@20 {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio4 20 GPIO_ACTIVE_HIGH>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <8>;
+ no-1-8-v;
+ non-removable;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* SS0# */
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x100b1
+ /* SS1# */
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x100b1
+ /* SS2# */
+ MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x100b1
+ /* WP pin NOR Flash */
+ MX6QDL_PAD_SD4_DAT7__GPIO2_IO15 0x4001b0b0
+ /* Flash nReset */
+ MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x4001b0b0
+ >;
+ };
+
+ pinctrl_ecspi4: ecspi4grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
+ MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x100b1 /* SS0# */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b1 /* SS1# */
+ >;
+ };
+
+ pinctrl_gpio: gpiogrp {
+ fsl,pins = <
+ /* led enable */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x4001b0b0
+ /* LCD power enable */
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x4001b0b0
+ /* led yellow */
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x4001b0b0
+ /* led red */
+ MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x4001b0b0
+ /* led green */
+ MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x4001b0b0
+ /* led blue */
+ MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x4001b0b0
+ /* Profibus IRQ */
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0
+ /* FPGA IRQ currently unused*/
+ MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x1b0b0
+ /* Display reset because of clock failure */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x4001b0b0
+ /* spi bus #2 SS driver enable */
+ MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x4001b0b0
+ /* RST_LOC# PHY reset input (has pull-down!)*/
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x4001b0b0
+ /* Touchscreen IRQ */
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ /* PCIe reset */
+ MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x4001b0b0
+ /* make sure pin is GPIO and not ENET_REF_CLK */
+ MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001a0b0
+ /* TPM PP */
+ MX6QDL_PAD_EIM_A21__GPIO2_IO17 0x4001b0b0
+ /* TPM Reset */
+ MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x4001b0b0
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x1b0b0
+ MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX 0x1b0b0
+ MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ /* SD1 card detect input */
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0
+ /* SD1 write protect input */
+ MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+ MX6QDL_PAD_NANDF_D4__SD2_DATA4 0x17059
+ MX6QDL_PAD_NANDF_D5__SD2_DATA5 0x17059
+ MX6QDL_PAD_NANDF_D6__SD2_DATA6 0x17059
+ MX6QDL_PAD_NANDF_D7__SD2_DATA7 0x17059
+ >;
+ };
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ /* Will be filled by the bootloader */
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0>;
+ };
+
+ ir_recv: ir-receiver {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio3 9 1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cubox_i_ir>;
+ };
+
+ pwmleds {
+ compatible = "pwm-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cubox_i_pwm1>;
+
+ front {
+ active-low;
+ label = "imx6:red:front";
+ max-brightness = <248>;
+ pwms = <&pwm1 0 50000>;
+ };
+ };
+
+ v_5v0: regulator-v-5v0 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "v_5v0";
+ };
+
+ v_usb2: regulator-v-usb2 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cubox_i_usbh1_vbus>;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "v_usb2";
+ vin-supply = <&v_5v0>;
+ };
+
+ v_usb1: regulator-v-usb1 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cubox_i_usbotg_vbus>;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "v_usb1";
+ vin-supply = <&v_5v0>;
+ };
+
+ sound-spdif {
+ compatible = "fsl,imx-audio-spdif";
+ model = "Integrated SPDIF";
+ /* IMX6 doesn't implement this yet */
+ spdif-controller = <&spdif>;
+ spdif-out;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&pinctrl_gpio_key>;
+ pinctrl-names = "default";
+
+ button_0 {
+ label = "Button 0";
+ gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ };
+ };
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cubox_i_hdmi>;
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cubox_i_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cubox_i_i2c3>;
+
+ status = "okay";
+
+ rtc@68 {
+ compatible = "nxp,pcf8523";
+ reg = <0x68>;
+ };
+};
+
+&iomuxc {
+ cubox_i {
+ pinctrl_cubox_i_hdmi: cubox-i-hdmi {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_cubox_i_i2c2: cubox-i-i2c2 {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_cubox_i_i2c3: cubox-i-i2c3 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_cubox_i_ir: cubox-i-ir {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x80000000
+ >;
+ };
+
+ pinctrl_cubox_i_pwm1: cubox-i-pwm1-front-led {
+ fsl,pins = <MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0>;
+ };
+
+ pinctrl_cubox_i_spdif: cubox-i-spdif {
+ fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
+ };
+
+ pinctrl_cubox_i_usbh1: cubox-i-usbh1 {
+ fsl,pins = <MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0>;
+ };
+
+ pinctrl_cubox_i_usbh1_vbus: cubox-i-usbh1-vbus {
+ fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>;
+ };
+
+ pinctrl_cubox_i_usbotg: cubox-i-usbotg {
+ /*
+ * The Cubox-i pulls ID low, but as it's pointless
+ * leaving it as a pull-up, even if it is just 10uA.
+ */
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ >;
+ };
+
+ pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbus {
+ fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x4001b0b0>;
+ };
+
+ pinctrl_cubox_i_usdhc2_aux: cubox-i-usdhc2-aux {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071
+ MX6QDL_PAD_KEY_ROW1__SD2_VSELECT 0x1b071
+ >;
+ };
+
+ pinctrl_cubox_i_usdhc2: cubox-i-usdhc2 {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
+ >;
+ };
+
+ pinctrl_gpio_key: gpio-key {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x17059
+ >;
+ };
+ };
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cubox_i_spdif>;
+ status = "okay";
+};
+
+&usbh1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cubox_i_usbh1>;
+ vbus-supply = <&v_usb2>;
+ status = "okay";
+};
+
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cubox_i_usbotg>;
+ vbus-supply = <&v_usb1>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cubox_i_usdhc2_aux &pinctrl_cubox_i_usdhc2>;
+ vmmc-supply = <&vcc_3v3>;
+ cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&vcc_3v3 {
+ vin-supply = <&v_5v0>;
+};
--- /dev/null
+/*
+ * Copyright (C) 2013,2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ /* Will be filled by the bootloader */
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0>;
+ };
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ ir_recv: ir-receiver {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio3 5 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_gpio3_5>;
+ };
+
+ v_3v2: regulator-v-3v2 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "v_3v2";
+ vin-supply = <&v_5v0>;
+ };
+
+ v_5v0: regulator-v-5v0 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "v_5v0";
+ };
+
+ v_sd: regulator-v-sd {
+ compatible = "regulator-fixed";
+ gpio = <&gpio4 30 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_vmmc>;
+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "v_sd";
+ startup-delay-us = <1000>;
+ vin-supply = <&v_3v2>;
+ };
+
+ v_usb2: regulator-v-usb2 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_usbh1_vbus>;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "v_usb2";
+ vin-supply = <&v_5v0>;
+ };
+
+ v_usb1: regulator-v-usb1 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_usbotg_vbus>;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "v_usb1";
+ vin-supply = <&v_5v0>;
+ };
+
+ audio: sound-sgtl5000 {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "On-board Codec";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&sound_codec>;
+ simple-audio-card,frame-master = <&sound_codec>;
+ simple-audio-card,widgets =
+ "Microphone", "Headphone Jack",
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "MIC_IN", "Headphone Jack",
+ "Headphone Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+
+ sound_cpu: simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ };
+
+ sound_codec: simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ };
+ };
+
+ sound-spdif {
+ compatible = "fsl,imx-audio-spdif";
+ model = "On-board SPDIF";
+ /* IMX6 doesn't implement this yet */
+ spdif-controller = <&spdif>;
+ spdif-out;
+ };
+};
+
+&audmux {
+ status = "okay";
+
+ ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_SYN |
+ IMX_AUDMUX_V2_PTCR_TFSEL(4) |
+ IMX_AUDMUX_V2_PTCR_TCSEL(4) |
+ IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR)
+ IMX_AUDMUX_V2_PDCR_RXDSEL(4)
+ >;
+ };
+
+ pins5 {
+ fsl,audmux-port = <4>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN
+ IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ >;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_flexcan1>;
+ status = "okay";
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_hdmi>;
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_i2c1>;
+ status = "okay";
+
+ /* Pro baseboard model */
+ rtc@68 {
+ compatible = "nxp,pcf8523";
+ reg = <0x68>;
+ };
+
+ /* Pro baseboard model */
+ sgtl5000: codec@a {
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ compatible = "fsl,sgtl5000";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_sgtl5000>;
+ #sound-dai-cells = <0>;
+ reg = <0x0a>;
+ VDDA-supply = <&v_3v2>;
+ VDDIO-supply = <&v_3v2>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_i2c2>;
+ status = "okay";
+};
+
+&iomuxc {
+ hummingboard {
+ pinctrl_hummingboard_flexcan1: hummingboard-flexcan1 {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x80000000
+ MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x80000000
+ >;
+ };
+
+ pinctrl_hummingboard_gpio3_5: hummingboard-gpio3_5 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x1b0b1
+ >;
+ };
+
+ pinctrl_hummingboard_hdmi: hummingboard-hdmi {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_hummingboard_i2c1: hummingboard-i2c1 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_hummingboard_i2c2: hummingboard-i2c2 {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_hummingboard_pcie_reset: hummingboard-pcie-reset {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x1b0b1
+ >;
+ };
+
+ pinctrl_hummingboard_pwm1: pwm1grp {
+ fsl,pins = <MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b1>;
+ };
+
+ pinctrl_hummingboard_sgtl5000: hummingboard-sgtl5000 {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0
+ MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0
+ MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x110b0
+ MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x130b0
+ MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x130b0
+ >;
+ };
+
+ pinctrl_hummingboard_spdif: hummingboard-spdif {
+ fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
+ };
+
+ pinctrl_hummingboard_usbh1_vbus: hummingboard-usbh1-vbus {
+ fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
+ };
+
+ pinctrl_hummingboard_usbotg_id: hummingboard-usbotg-id {
+ /*
+ * We want it pulled down for a fixed host connection.
+ */
+ fsl,pins = <MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x13059>;
+ };
+
+ pinctrl_hummingboard_usbotg_vbus: hummingboard-usbotg-vbus {
+ fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
+ };
+
+ pinctrl_hummingboard_usdhc2_aux: hummingboard-usdhc2-aux {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071
+ >;
+ };
+
+ pinctrl_hummingboard_usdhc2: hummingboard-usdhc2 {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
+ >;
+ };
+ pinctrl_hummingboard_vmmc: hummingboard-vmmc {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
+ >;
+ };
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_pcie_reset>;
+ reset-gpio = <&gpio3 4 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_pwm1>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_spdif>;
+ status = "okay";
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&usbh1 {
+ disable-over-current;
+ vbus-supply = <&v_usb2>;
+ status = "okay";
+};
+
+&usbotg {
+ disable-over-current;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_usbotg_id>;
+ vbus-supply = <&v_usb1>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &pinctrl_hummingboard_usdhc2_aux
+ &pinctrl_hummingboard_usdhc2
+ >;
+ vmmc-supply = <&v_sd>;
+ cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&vcc_3v3 {
+ vin-supply = <&v_3v2>;
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "imx6qdl-u-boot.dtsi"
+
+/ {
+ board-detect {
+ compatible = "solidrun,hummingboard-detect";
+ detect-gpios = <
+ &gpio2 8 0
+ &gpio3 4 0
+ &gpio4 9 0
+ &gpio6 0 0
+ &gpio6 4 0
+ >;
+ };
+};
+
+&gpio2 {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio3 {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio4 {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio6 {
+ u-boot,dm-pre-reloc;
+};
+
+&usdhc1 {
+ status = "disabled";
+};
--- /dev/null
+/*
+ * Device Tree file for SolidRun HummingBoard2
+ * Copyright (C) 2015 Rabeeh Khoury <rabeeh@solid-run.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+&iomuxc {
+ hummingboard2 {
+ pinctrl_hummingboard2_usdhc3: hummingboard2-usdhc3 {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x17059
+ >;
+ };
+ };
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_usdhc3>;
+ vmmc-supply = <&v_3v2>;
+ vqmmc-supply = <&v_3v2>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright (C) 2015 Rabeeh Khoury <rabeeh@solid-run.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ /* Will be filled by the bootloader */
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0>;
+ };
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ ir_recv: ir-receiver {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio7 9 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_gpio7_9>;
+ linux,rc-map-name = "rc-rc6-mce";
+ };
+
+ v_3v2: regulator-v-3v2 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "v_3v2";
+ };
+
+ v_5v0: regulator-v-5v0 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "v_5v0";
+ };
+
+ vcc_1p8: regulator-vcc-1p8 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-name = "vcc_1p8";
+ vin-supply = <&v_3v2>;
+ };
+
+ v_sd: regulator-v-sd {
+ compatible = "regulator-fixed";
+ gpio = <&gpio4 30 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_vmmc>;
+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "v_sd";
+ startup-delay-us = <1000>;
+ vin-supply = <&v_3v2>;
+ };
+
+ v_usb1: regulator-v-usb1 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_usbotg_vbus>;
+ regulator-always-on;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "v_usb1";
+ vin-supply = <&v_5v0>;
+ };
+
+ v_usb2: regulator-v-usb2 {
+ /* USB hub port 1 */
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_usbh1_vbus>;
+ regulator-always-on;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "v_usb2";
+ vin-supply = <&v_5v0>;
+ };
+
+ v_usb3: regulator-v-usb3 {
+ /* USB hub port 3 */
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_usbh2_vbus>;
+ regulator-always-on;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "v_usb3";
+ vin-supply = <&v_5v0>;
+ };
+
+ v_usb4: regulator-v-usb4 {
+ /* USB hub port 4 */
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio7 10 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_usbh3_vbus>;
+ regulator-always-on;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "v_usb4";
+ vin-supply = <&v_5v0>;
+ };
+
+ audio: sound-sgtl5000 {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "On-board Codec";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&sound_codec>;
+ simple-audio-card,frame-master = <&sound_codec>;
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+
+ sound_cpu: simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ };
+
+ sound_codec: simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ };
+ };
+};
+
+&audmux {
+ status = "okay";
+
+ ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_SYN |
+ IMX_AUDMUX_V2_PTCR_TFSEL(4) |
+ IMX_AUDMUX_V2_PTCR_TCSEL(4) |
+ IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR)
+ IMX_AUDMUX_V2_PDCR_RXDSEL(4)
+ >;
+ };
+
+ pins5 {
+ fsl,audmux-port = <4>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN
+ IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ >;
+ };
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_ecspi2>;
+ cs-gpios = <&gpio2 26 0>;
+ status = "okay";
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_hdmi>;
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_i2c1>;
+ status = "okay";
+
+ pcf8523: rtc@68 {
+ compatible = "nxp,pcf8523";
+ reg = <0x68>;
+ };
+
+ sgtl5000: codec@a {
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ compatible = "fsl,sgtl5000";
+ #sound-dai-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_sgtl5000>;
+ reg = <0x0a>;
+ VDDA-supply = <&v_3v2>;
+ VDDD-supply = <&vcc_1p8>;
+ VDDIO-supply = <&v_3v2>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_i2c3>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ hummingboard2 {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /*
+ * 36 pin headers GPIO description. The pins
+ * numbering as following -
+ *
+ * 3.2v 5v 74 75
+ * 73 72 71 70
+ * 69 68 67 66
+ *
+ * 77 78 79 76
+ * 65 64 61 60
+ * 53 52 51 50
+ * 49 48 166 132
+ * 95 94 90 91
+ * GND 54 24 204
+ *
+ * The GPIO numbers can be extracted using
+ * signal name from below.
+ * Example -
+ * MX6QDL_PAD_EIM_DA10__GPIO3_IO10 is
+ * GPIO(3,10) which is (3-1)*32+10 = gpio 74
+ *
+ * i.e. The mapping of GPIO(X,Y) to Linux gpio
+ * number is : gpio number = (X-1) * 32 + Y
+ */
+ /* DI1_PIN15 */
+ MX6QDL_PAD_EIM_DA10__GPIO3_IO10 0x400130b1
+ /* DI1_PIN02 */
+ MX6QDL_PAD_EIM_DA11__GPIO3_IO11 0x400130b1
+ /* DISP1_DATA00 */
+ MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x400130b1
+ /* DISP1_DATA01 */
+ MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x400130b1
+ /* DISP1_DATA02 */
+ MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x400130b1
+ /* DISP1_DATA03 */
+ MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x400130b1
+ /* DISP1_DATA04 */
+ MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x400130b1
+ /* DISP1_DATA05 */
+ MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x400130b1
+ /* DISP1_DATA06 */
+ MX6QDL_PAD_EIM_DA3__GPIO3_IO03 0x400130b1
+ /* DISP1_DATA07 */
+ MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x400130b1
+ /* DI1_D0_CS */
+ MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x400130b1
+ /* DI1_D1_CS */
+ MX6QDL_PAD_EIM_DA14__GPIO3_IO14 0x400130b1
+ /* DI1_PIN01 */
+ MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x400130b1
+ /* DI1_PIN03 */
+ MX6QDL_PAD_EIM_DA12__GPIO3_IO12 0x400130b1
+ /* DISP1_DATA08 */
+ MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x400130b1
+ /* DISP1_DATA09 */
+ MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x400130b1
+ /* DISP1_DATA10 */
+ MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x400130b1
+ /* DISP1_DATA11 */
+ MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x400130b1
+ /* DISP1_DATA12 */
+ MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x400130b1
+ /* DISP1_DATA13 */
+ MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x400130b1
+ /* DISP1_DATA14 */
+ MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x400130b1
+ /* DISP1_DATA15 */
+ MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x400130b1
+ /* DISP1_DATA16 */
+ MX6QDL_PAD_EIM_A21__GPIO2_IO17 0x400130b1
+ /* DISP1_DATA17 */
+ MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x400130b1
+ /* DISP1_DATA18 */
+ MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x400130b1
+ /* DISP1_DATA19 */
+ MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x400130b1
+ /* DISP1_DATA20 */
+ MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x400130b1
+ /* DISP1_DATA21 */
+ MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x400130b1
+ /* DISP1_DATA22 */
+ MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x400130b1
+ /* DISP1_DATA23 */
+ MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x400130b1
+ /* DI1_DISP_CLK */
+ MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x400130b1
+ /* SPDIF_IN */
+ MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24 0x400130b1
+ /* SPDIF_OUT */
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x400130b1
+
+ /* MikroBUS GPIO pin number 10 */
+ MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x400130b1
+ >;
+ };
+
+ pinctrl_hummingboard2_ecspi2: hummingboard2-ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1 /* CS */
+ >;
+ };
+
+ pinctrl_hummingboard2_gpio7_9: hummingboard2-gpio7_9 {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__GPIO7_IO09 0x80000000
+ >;
+ };
+
+ pinctrl_hummingboard2_hdmi: hummingboard2-hdmi {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_hummingboard2_i2c1: hummingboard2-i2c1 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_hummingboard2_i2c2: hummingboard2-i2c2 {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_hummingboard2_i2c3: hummingboard2-i2c3 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_hummingboard2_mipi: hummingboard2_mipi {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x4001b8b1
+ MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x4001b8b1
+ MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x130b0
+ >;
+ };
+
+ pinctrl_hummingboard2_pcie_reset: hummingboard2-pcie-reset {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b1
+ >;
+ };
+
+ pinctrl_hummingboard2_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_hummingboard2_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_hummingboard2_sgtl5000: hummingboard2-sgtl5000 {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0
+ MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0
+ MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x110b0
+ MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x130b0
+ MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x130b0
+ >;
+ };
+
+ pinctrl_hummingboard2_usbh1_vbus: hummingboard2-usbh1-vbus {
+ fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
+ };
+
+ pinctrl_hummingboard2_usbh2_vbus: hummingboard2-usbh2-vbus {
+ fsl,pins = <MX6QDL_PAD_SD4_DAT5__GPIO2_IO13 0x1b0b0>;
+ };
+
+ pinctrl_hummingboard2_usbh3_vbus: hummingboard2-usbh3-vbus {
+ fsl,pins = <MX6QDL_PAD_SD4_CLK__GPIO7_IO10 0x1b0b0>;
+ };
+
+ pinctrl_hummingboard2_usbotg_id: hummingboard2-usbotg-id {
+ /*
+ * We want it pulled down for a fixed host connection.
+ */
+ fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+ };
+
+ pinctrl_hummingboard2_usbotg_vbus: hummingboard2-usbotg-vbus {
+ fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
+ };
+
+ pinctrl_hummingboard2_usdhc2_aux: hummingboard2-usdhc2-aux {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071
+ MX6QDL_PAD_KEY_ROW1__SD2_VSELECT 0x1b071
+ >;
+ };
+
+ pinctrl_hummingboard2_usdhc2: hummingboard2-usdhc2 {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
+ >;
+ };
+
+ pinctrl_hummingboard2_usdhc2_100mhz: hummingboard2-usdhc2-100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x130b9
+ >;
+ };
+
+ pinctrl_hummingboard2_usdhc2_200mhz: hummingboard2-usdhc2-200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170f9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100f9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x130f9
+ >;
+ };
+
+ pinctrl_hummingboard2_vmmc: hummingboard2-vmmc {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_hummingboard2_uart3: hummingboard2-uart3 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D25__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D24__UART3_RX_DATA 0x40013000
+ >;
+ };
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_pcie_reset>;
+ reset-gpio = <&gpio2 11 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_pwm1>;
+ status = "okay";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_pwm3>;
+ status = "okay";
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&usbh1 {
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg {
+ disable-over-current;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_usbotg_id>;
+ vbus-supply = <&v_usb1>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <
+ &pinctrl_hummingboard2_usdhc2_aux
+ &pinctrl_hummingboard2_usdhc2
+ >;
+ pinctrl-1 = <
+ &pinctrl_hummingboard2_usdhc2_aux
+ &pinctrl_hummingboard2_usdhc2_100mhz
+ >;
+ pinctrl-2 = <
+ &pinctrl_hummingboard2_usdhc2_aux
+ &pinctrl_hummingboard2_usdhc2_200mhz
+ >;
+ vmmc-supply = <&v_sd>;
+ cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard2_uart3>;
+ status = "okay";
+};
+
+&vcc_3v3 {
+ vin-supply = <&v_3v2>;
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Jacopo Mondi <jacopo@jmondi.org>
+ */
+
+#include "imx6qdl-icore.dtsi"
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ >;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET_REF>;
+ status = "okay";
+};
+// SPDX-License-Identifier: GPL-2.0 OR X11
/*
* Copyright (C) 2015 Amarula Solutions B.V.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This file is distributed in the hope that it will be useful
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
+ * Copyright (C) 2015 Engicam S.r.l.
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
/ {
- aliases {
- mmc1 = &usdhc3;
- mmc2 = &usdhc4;
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x80000000>;
};
- memory {
- reg = <0x10000000 0x80000000>;
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "1P8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_2p5v: regulator-2p5v {
+ compatible = "regulator-fixed";
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_sd3_vmmc: regulator-sd3-vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "P3V3_SD3_SWITCHED";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ enable-active-high;
+ };
+
+ reg_sd4_vmmc: regulator-sd4-vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "P3V3_SD4_SWITCHED";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_usb_h1_vbus: regulator-usb-h1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ usb_hub: usb-hub {
+ compatible = "smsc,usb3503a";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbhub>;
+ reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>;
+ clock-names = "refclk";
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "imx6qdl-icore-rqs-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&dailink_master>;
+ simple-audio-card,frame-master = <&dailink_master>;
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Headphone", "Headphone Jack",
+ "Line", "Line In Jack",
+ "Speaker", "Line Out Jack",
+ "Speaker", "Ext Spk";
+ simple-audio-card,routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ };
+
+ dailink_master: simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ };
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ audmux_ssi1 {
+ fsl,audmux-port = <MX51_AUDMUX_PORT1_SSI0>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TFSEL(MX51_AUDMUX_PORT4) |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR |
+ IMX_AUDMUX_V2_PTCR_TCSEL(MX51_AUDMUX_PORT4) |
+ IMX_AUDMUX_V2_PTCR_SYN)
+ IMX_AUDMUX_V2_PDCR_RXDSEL(MX51_AUDMUX_PORT4)
+ >;
};
+
+ audmux_aud4 {
+ fsl,audmux-port = <MX51_AUDMUX_PORT4>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN
+ IMX_AUDMUX_V2_PDCR_RXDSEL(MX51_AUDMUX_PORT1_SSI0)
+ >;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ xceiver-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ xceiver-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
};
&fec {
status = "okay";
mdio {
- eth_phy: ethernet-phy {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ eth_phy: ethernet-phy@0 {
+ reg = <0x0>;
rxc-skew-ps = <1140>;
txc-skew-ps = <1140>;
txen-skew-ps = <600>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
+
+ sgtl5000: codec@a {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ VDDA-supply = <®_2p5v>;
+ VDDIO-supply = <®_3p3v>;
+ VDDD-supply = <®_1p8v>;
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio3 29 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&ssi1 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
};
&uart4 {
status = "okay";
};
-&usdhc3 {
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ disable-over-current;
+ clocks = <&clks IMX6QDL_CLK_USBOH3>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ vmcc-supply = <®_sd3_vmmc>;
cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
no-1-8-v;
status = "okay";
};
pinctrl-0 = <&pinctrl_usdhc4>;
pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
- bus-witdh = <8>;
+ vmcc-supply = <®_sd4_vmmc>;
+ bus-width = <8>;
no-1-8-v;
non-removable;
status = "okay";
};
&iomuxc {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
+ MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0
+ MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
+ MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
+ >;
+ };
+
pinctrl_enet: enetgrp {
fsl,pins = <
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
>;
};
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b020
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b020
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b020
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b020
+ >;
+ };
+
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
fsl,pins = <
MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1f059 /* PCIe Reset */
>;
};
>;
};
+ pinctrl_usbhub: usbhubgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1f059 /* HUB USB Reset */
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10071
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071
+ >;
+ };
+
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17070
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17070
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17070
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17070
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1f059 /* CD */
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f059 /* PWR */
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170B1
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100B1
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170B1
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170B1
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170B1
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B1
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170F9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100F9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170F9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170F9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170F9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170F9
>;
};
MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170F9
>;
};
-
};
+// SPDX-License-Identifier: GPL-2.0 OR X11
/*
* Copyright (C) 2016 Amarula Solutions B.V.
* Copyright (C) 2016 Engicam S.r.l.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This file is distributed in the hope that it will be useful
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
/ {
- aliases {
- mmc1 = &usdhc3;
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x80000000>;
};
- memory {
- reg = <0x10000000 0x80000000>;
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ backlight_lvds: backlight-lvds {
+ compatible = "pwm-backlight";
+ pwms = <&pwm3 0 100000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "1P8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_2p5v: regulator-2p5v {
+ compatible = "regulator-fixed";
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-boot-on;
+ regulator-always-on;
};
reg_3p3v: regulator-3p3v {
regulator-boot-on;
regulator-always-on;
};
+
+ reg_usb_h1_vbus: regulator-usb-h1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ rmii_clk: clock-rmii-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>; /* 25MHz for example */
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "imx6qdl-icore-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&dailink_master>;
+ simple-audio-card,frame-master = <&dailink_master>;
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Headphone", "Headphone Jack",
+ "Line", "Line In Jack",
+ "Speaker", "Line Out Jack",
+ "Speaker", "Ext Spk";
+ simple-audio-card,routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ };
+
+ dailink_master: simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ };
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+
+ audmux_ssi1 {
+ fsl,audmux-port = <MX51_AUDMUX_PORT1_SSI0>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TFSEL(MX51_AUDMUX_PORT4) |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR |
+ IMX_AUDMUX_V2_PTCR_TCSEL(MX51_AUDMUX_PORT4) |
+ IMX_AUDMUX_V2_PTCR_SYN)
+ IMX_AUDMUX_V2_PDCR_RXDSEL(MX51_AUDMUX_PORT4)
+ >;
+ };
+
+ audmux_aud4 {
+ fsl,audmux-port = <MX51_AUDMUX_PORT4>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN
+ IMX_AUDMUX_V2_PDCR_RXDSEL(MX51_AUDMUX_PORT1_SSI0)
+ >;
+ };
};
&can1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+ clocks = <&clks IMX6QDL_CLK_ENET>, <&clks IMX6QDL_CLK_ENET>, <&rmii_clk>;
phy-mode = "rmii";
status = "okay";
};
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
+
+ ov5640: camera@3c {
+ compatible = "ovti,ov5640";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5640>;
+ reg = <0x3c>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ clock-names = "xclk";
+ DOVDD-supply = <®_1p8v>;
+ AVDD-supply = <®_3p3v>;
+ DVDD-supply = <®_3p3v>;
+ powerdown-gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio5 31 GPIO_ACTIVE_LOW>;
+ status = "disabled";
+
+ port {
+ ov5640_to_mipi_csi2: endpoint {
+ remote-endpoint = <&mipi_csi2_in>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+
+ sgtl5000: codec@a {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ VDDA-supply = <®_2p5v>;
+ VDDIO-supply = <®_3p3v>;
+ VDDD-supply = <®_1p8v>;
+ };
+};
+
+&mipi_csi {
+ status = "disabled";
+
+ port@0 {
+ reg = <0>;
+
+ mipi_csi2_in: endpoint {
+ remote-endpoint = <&ov5640_to_mipi_csi2>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
+
+&ssi1 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
};
&uart4 {
status = "okay";
};
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
&usdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc1>;
};
&iomuxc {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
+ MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0
+ MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
+ MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
+ >;
+ };
+
pinctrl_enet: enetgrp {
fsl,pins = <
MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
>;
};
- pinctrl_gpmi_nand: gpmi-nand {
+ pinctrl_gpmi_nand: gpminandgrp {
fsl,pins = <
MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
fsl,pins = <
MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
- MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
+ >;
+ };
+
+ pinctrl_ov5640: ov5640grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__GPIO5_IO30 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__GPIO5_IO31 0x1b0b0
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
>;
};
>;
};
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ >;
+ };
+
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17070
--- /dev/null
+/*
+ * Copyright (C) 2013,2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/gpio/gpio.h>
+/ {
+ clk_brcm: brcm-clock {
+ compatible = "gpio-gate-clock";
+ #clock-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_brcm_osc>;
+ enable-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_brcm: brcm-reg {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio3 19 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_brcm_reg>;
+ regulator-name = "brcm_reg";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <200000>;
+ };
+
+ usdhc1_pwrseq: usdhc1_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio5 26 GPIO_ACTIVE_LOW>,
+ <&gpio6 0 GPIO_ACTIVE_LOW>;
+ clocks = <&clk_brcm>;
+ clock-names = "ext_clock";
+ };
+};
+
+&iomuxc {
+ microsom {
+ pinctrl_microsom_brcm_bt: microsom-brcm-bt {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00 0x40013070
+ MX6QDL_PAD_CSI0_DAT15__GPIO6_IO01 0x40013070
+ MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04 0x40013070
+ >;
+ };
+
+ pinctrl_microsom_brcm_osc: microsom-brcm-osc {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x40013070
+ >;
+ };
+
+ pinctrl_microsom_brcm_reg: microsom-brcm-reg {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x40013070
+ >;
+ };
+
+ pinctrl_microsom_brcm_wifi: microsom-brcm-wifi {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__XTALOSC_REF_CLK_32K 0x1b0b0
+ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x40013070
+ MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x40013070
+ MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x40013070
+ >;
+ };
+
+ pinctrl_microsom_uart4: microsom-uart4 {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_microsom_usdhc1: microsom-usdhc1 {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ >;
+ };
+ };
+};
+
+/* UART4 - Connected to optional BRCM Wifi/BT/FM */
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_brcm_bt &pinctrl_microsom_uart4>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+/* USDHC1 - Connected to optional BRCM Wifi/BT/FM */
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_brcm_wifi &pinctrl_microsom_usdhc1>;
+ bus-width = <4>;
+ mmc-pwrseq = <&usdhc1_pwrseq>;
+ keep-power-in-suspend;
+ no-1-8-v;
+ non-removable;
+ vmmc-supply = <®_brcm>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright (C) 2013,2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+&iomuxc {
+ microsom {
+ pinctrl_microsom_usdhc3: microsom-usdhc3 {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x17059
+ >;
+ };
+ };
+};
+
+/* USDHC3 - eMMC */
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_usdhc3>;
+ bus-width = <8>;
+ non-removable;
+ vmmc-supply = <&vcc_3v3>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright (C) 2013,2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ nvcc_sd1: regulator-nvcc-sd1 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-name = "nvcc_sd1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ };
+
+ clk_ti_wifi: ti-wifi-clock {
+ /* This is a hack around the kernel - using "fixed clock"
+ * results in the "pinctrl" properties being ignored, and
+ * the clock not being output. Instead, use a gated clock
+ * and the unrouted WL_XTAL_PU gpio.
+ */
+ compatible = "gpio-gate-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_ti_clk>;
+ enable-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwrseq_ti_wifi: ti-wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_ti_wifi_en>;
+ reset-gpios = <&gpio5 26 GPIO_ACTIVE_LOW>;
+ post-power-on-delay-ms = <200>;
+ clocks = <&clk_ti_wifi>;
+ clock-names = "ext_clock";
+ };
+};
+
+&iomuxc {
+ microsom {
+ pinctrl_microsom_ti_bt: microsom-ti-bt {
+ fsl,pins = <
+ /* BT_EN_SOC */
+ MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00 0x40013070
+ >;
+ };
+
+ pinctrl_microsom_ti_clk: microsom-ti-clk {
+ fsl,pins = <
+ /* EXT_32K */
+ MX6QDL_PAD_GPIO_8__XTALOSC_REF_CLK_32K 0x1b0b0
+ /* WL_XTAL_PU (unrouted) */
+ MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x40013070
+ >;
+ };
+
+ pinctrl_microsom_ti_wifi_en: microsom-ti-wifi-en {
+ fsl,pins = <
+ /* WLAN_EN_SOC */
+ MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x40013070
+ >;
+ };
+
+ pinctrl_microsom_ti_wifi_irq: microsom-ti-wifi-irq {
+ fsl,pins = <
+ /* WLAN_IRQ */
+ MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04 0x40013070
+ >;
+ };
+
+ pinctrl_microsom_uart4: microsom-uart4 {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_microsom_usdhc1: microsom-usdhc1 {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ >;
+ };
+ };
+};
+
+/* UART4 - Connected to optional TI Wi-Fi/BT/FM */
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_uart4>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "ti,wl1837-st";
+ clocks = <&clk_ti_wifi>;
+ clock-names = "ext_clock";
+ enable-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_ti_bt>;
+ };
+};
+
+/* USDHC1 - Connected to optional TI Wi-Fi/BT/FM */
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_usdhc1>;
+ bus-width = <4>;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&pwrseq_ti_wifi>;
+ non-removable;
+ vmmc-supply = <&vcc_3v3>;
+ /* vqmmc-supply = <&nvcc_sd1>; - MMC layer doesn't like it! */
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wlcore@2 {
+ compatible = "ti,wl1837";
+ reg = <2>;
+ interrupts-extended = <&gpio6 4 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_ti_wifi_irq>;
+ };
+};
--- /dev/null
+/*
+ * Copyright (C) 2013,2014 Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ vcc_3v3: regulator-vcc-3v3 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-name = "vcc_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
+ phy-mode = "rgmii-id";
+ phy-reset-duration = <2>;
+ phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&iomuxc {
+ microsom {
+ pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b8b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ /* AR8035 reset */
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x130b0
+ /* AR8035 interrupt */
+ MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0
+ /* GPIO16 -> AR8035 25MHz */
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x13030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
+ /* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x0a0b1
+ /* AR8035 pin strapping: IO voltage: pull up */
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ /* AR8035 pin strapping: PHYADDR#0: pull down */
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x13030
+ /* AR8035 pin strapping: PHYADDR#1: pull down */
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x13030
+ /* AR8035 pin strapping: MODE#1: pull up */
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ /* AR8035 pin strapping: MODE#3: pull up */
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ /* AR8035 pin strapping: MODE#0: pull down */
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x13030
+
+ /*
+ * As the RMII pins are also connected to RGMII
+ * so that an AR8030 can be placed, set these
+ * to high-z with the same pulls as above.
+ * Use the GPIO settings to avoid changing the
+ * input select registers.
+ */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x03000
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x03000
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x03000
+ >;
+ };
+
+ pinctrl_microsom_uart1: microsom-uart1 {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_uart1>;
+ status = "okay";
+};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2018 Collabora Ltd.
- *
- * Based on dts[i] from Phytec barebox port:
- * Copyright (C) 2016 PHYTEC Messtechnik GmbH
- * Author: Christian Hemp <c.hemp@phytec.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-/dts-v1/;
-
-#include "imx6ul.dtsi"
-#include "pcl063-common.dtsi"
-
-/ {
- model = "Phytec phyBOARD-i.MX6UL-Segin SBC";
- compatible = "phytec,phyboard-imx6ul-segin", "phytec,imx6ul-pcl063",
- "fsl,imx6ul";
-};
-
-&gpmi {
- status = "okay";
-};
-
-&i2c1 {
- i2c_rtc: rtc@68 {
- compatible = "microcrystal,rv4162";
- reg = <0x68>;
- status = "okay";
- };
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart5>;
- uart-has-rtscts;
- status = "okay";
-};
-
-&usbotg1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usb_otg1_id>;
- dr_mode = "otg";
- srp-disable;
- hnp-disable;
- adp-disable;
- status = "okay";
-};
-
-&usbotg2 {
- dr_mode = "host";
- disable-over-current;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl-names = "default";
-
- pinctrl_uart5: uart5grp {
- fsl,pins = <
- MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1
- MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1
- MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x1b0b1
- MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x1b0b1
- >;
- };
-
- pinctrl_usb_otg1_id: usbotg1idgrp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059
- >;
- };
-
-};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "PHYTEC phyCORE-i.MX6 UltraLite";
+ compatible = "phytec,imx6ul-pcl063", "fsl,imx6ul";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+
+ gpio_leds_som: leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpioleds_som>;
+ compatible = "gpio-leds";
+
+ phycore-green {
+ gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ status = "disabled";
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ micrel,led-mode = <1>;
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "rmii-ref";
+ status = "disabled";
+ };
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ status = "disabled";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ clock-frequency = <100000>;
+ status = "okay";
+
+ eeprom@52 {
+ compatible = "catalyst,24c32", "atmel,24c32";
+ reg = <0x52>;
+ };
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <8>;
+ no-1-8-v;
+ non-removable;
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x10010
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x10010
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b010
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b010
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b010
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b010
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x17059
+ >;
+ };
+
+ pinctrl_gpioleds_som: gpioledssomgrp {
+ fsl,pins = <MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0>;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1
+ MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1
+ MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1
+ MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000
+ MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1
+ MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1
+ MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1
+ MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1
+ MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1
+ MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1
+ MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1
+ MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1
+ MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1
+ MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1
+ MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1
+ >;
+ };
+
+ pinctrl_i2c1: i2cgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
+ MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9
+ >;
+ };
+
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ul.dtsi"
+#include "imx6ul-phytec-phycore-som.dtsi"
+#include "imx6ul-phytec-segin.dtsi"
+#include "imx6ul-phytec-segin-peb-eval-01.dtsi"
+
+/ {
+ model = "PHYTEC phyBOARD-Segin i.MX6 UltraLite Full Featured with NAND";
+ compatible = "phytec,imx6ul-pbacd10-nand", "phytec,imx6ul-pbacd10",
+ "phytec,imx6ul-pcl063", "fsl,imx6ul";
+};
+
+&adc1 {
+ status = "okay";
+};
+
+&can1 {
+ status = "okay";
+};
+
+&tlv320 {
+ status = "okay";
+};
+
+&ecspi3 {
+ status = "okay";
+};
+
+ðphy1 {
+ status = "okay";
+};
+
+ðphy2 {
+ status = "okay";
+};
+
+&fec1 {
+ status = "okay";
+};
+
+&fec2 {
+ status = "okay";
+};
+
+&gpmi {
+ status = "okay";
+};
+
+&i2c_rtc {
+ status = "okay";
+};
+
+®_can1_en {
+ status = "okay";
+};
+
+®_sound_1v8 {
+ status = "okay";
+};
+
+®_sound_3v3 {
+ status = "okay";
+};
+
+&sai2 {
+ status = "okay";
+};
+
+&sound {
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&usbotg1 {
+ status = "okay";
+};
+
+&usbotg2 {
+ status = "okay";
+};
+
+&usdhc1 {
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016 PHYTEC Messtechnik
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ gpio_keys: gpio-keys {
+ compatible = "gpio-key";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+ status = "disabled";
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ user_leds: user-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_user_leds>;
+ status = "disabled";
+
+ user-led1 {
+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "gpio";
+ default-state = "on";
+ };
+
+ user-led2 {
+ gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "gpio";
+ default-state = "on";
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl_gpio_keys: gpio_keysgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x79
+ >;
+ };
+
+ pinctrl_user_leds: user_ledsgrp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x79
+ MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0x79
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+/ {
+ model = "PHYTEC phyBOARD-Segin i.MX6 UltraLite";
+ compatible = "phytec,imx6ul-pbacd-10", "phytec,imx6ul-pcl063", "fsl,imx6ul";
+
+ aliases {
+ rtc0 = &i2c_rtc;
+ rtc1 = &snvs_rtc;
+ };
+
+ reg_sound_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "i2s-audio-1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ status = "disabled";
+ };
+
+ reg_sound_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "i2s-audio-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ status = "disabled";
+ };
+
+ reg_can1_en: regulator-can1 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&princtrl_flexcan1_en>;
+ regulator-name = "Can";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ status = "disabled";
+ };
+
+ reg_adc1_vref_3v3: regulator-vref-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ sound: sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "phyBOARD-Segin-TLV320AIC3007";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&dailink_master>;
+ simple-audio-card,frame-master = <&dailink_master>;
+ simple-audio-card,widgets =
+ "Line", "Line In",
+ "Line", "Line Out",
+ "Speaker", "Speaker";
+ simple-audio-card,routing =
+ "Line Out", "LLOUT",
+ "Line Out", "RLOUT",
+ "Speaker", "SPOP",
+ "Speaker", "SPOM",
+ "LINE1L", "Line In",
+ "LINE1R", "Line In";
+ status = "disabled";
+
+ simple-audio-card,cpu {
+ sound-dai = <&sai2>;
+ };
+
+ dailink_master: simple-audio-card,codec {
+ sound-dai = <&tlv320>;
+ clocks = <&clks IMX6UL_CLK_SAI2>;
+ };
+ };
+
+};
+
+&adc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc1>;
+ vref-supply = <®_adc1_vref_3v3>;
+ /*
+ * driver can not separate a specific channel so we request 4 channels
+ * here - we need only the fourth channel
+ */
+ num-channels = <4>;
+ status = "disabled";
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_can1_en>;
+ status = "disabled";
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+ assigned-clock-rates = <786432000>;
+};
+
+&ecspi3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ cs-gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy2>;
+ status = "disabled";
+};
+
+&i2c1 {
+ tlv320: codec@18 {
+ compatible = "ti,tlv320aic3007";
+ #sound-dai-cells = <0>;
+ reg = <0x18>;
+ AVDD-supply = <®_sound_3v3>;
+ IOVDD-supply = <®_sound_3v3>;
+ DRVDD-supply = <®_sound_3v3>;
+ DVDD-supply = <®_sound_1v8>;
+ status = "disabled";
+ };
+
+ stmpe: touchscreen@44 {
+ compatible = "st,stmpe811";
+ reg = <0x44>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_stmpe>;
+ status = "disabled";
+
+ touchscreen {
+ compatible = "st,stmpe-ts";
+ st,sample-time = <4>;
+ st,mod-12b = <1>;
+ st,ref-sel = <0>;
+ st,adc-freq = <1>;
+ st,ave-ctrl = <1>;
+ st,touch-det-delay = <2>;
+ st,settling = <2>;
+ st,fraction-z = <7>;
+ st,i-drive = <1>;
+ touchscreen-inverted-x = <1>;
+ touchscreen-inverted-y = <1>;
+ };
+ };
+
+ i2c_rtc: rtc@68 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc_int>;
+ compatible = "microcrystal,rv4162";
+ reg = <0x68>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+ status = "disabled";
+ };
+};
+
+&mdio {
+ ethphy2: ethernet-phy@2 {
+ reg = <2>;
+ micrel,led-mode = <1>;
+ clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+ clock-names = "rmii-ref";
+ status = "disabled";
+ };
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "disabled";
+};
+
+&sai2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai2>;
+ assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>,
+ <&clks IMX6UL_CLK_SAI2>;
+ assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+ assigned-clock-rates = <0>, <19200000>;
+ fsl,sai-mclk-direction-output;
+ status = "disabled";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ uart-has-rtscts;
+ status = "disabled";
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1_id>;
+ dr_mode = "otg";
+ status = "disabled";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ status = "disabled";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_adc1: adc1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO 0x10b0
+ MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x10b0
+ MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x10b0
+ MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20 0x10b0
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b010
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b010
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b010
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b010
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1 {
+ fsl,pins = <
+ MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x0b0b0
+ MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x0b0b0
+ >;
+ };
+
+ princtrl_flexcan1_en: flexcan1engrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x17059
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO04__PWM3_OUT 0x0b0b0
+ >;
+ };
+
+ pinctrl_rtc_int: rtcintgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x17059
+ >;
+ };
+
+ pinctrl_sai2: sai2grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088
+ MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088
+ MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x11088
+ MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x11088
+ MX6UL_PAD_JTAG_TMS__SAI2_MCLK 0x17088
+ >;
+ };
+
+ pinctrl_stmpe: stmpegrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x17059
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1
+ MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x1b0b1
+ MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1_id: usbotg1idgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
+ >;
+ };
+};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
- */
-
-/dts-v1/;
-
-#include "imx6ull.dtsi"
-#include "pcl063-common.dtsi"
-
-/ {
- model = "Phytec phyBOARD-i.MX6ULL-Segin SBC";
- compatible = "phytec,phyboard-imx6ull-segin", "phytec,imx6ull-pcl063",
- "fsl,imx6ull";
-};
-
-&i2c1 {
- i2c_rtc: rtc@68 {
- compatible = "microcrystal,rv4162";
- reg = <0x68>;
- status = "okay";
- };
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart5>;
- uart-has-rtscts;
- status = "okay";
-};
-
-&usdhc2 {
- status = "okay";
-};
-
-&usbotg1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usb_otg1_id>;
- dr_mode = "otg";
- srp-disable;
- hnp-disable;
- adp-disable;
- status = "okay";
-};
-
-&usbotg2 {
- dr_mode = "host";
- disable-over-current;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl-names = "default";
-
- pinctrl_uart5: uart5grp {
- fsl,pins = <
- MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1
- MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1
- MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x1b0b1
- MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x1b0b1
- >;
- };
-
- pinctrl_usb_otg1_id: usbotg1idgrp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059
- >;
- };
-
-};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 PHYTEC Messtechnik GmbH
+ * Author: Stefan Riedmueller <s.riedmueller@phytec.de>
+ */
+
+#include "imx6ul-phytec-phycore-som.dtsi"
+
+/ {
+ model = "PHYTEC phyCORE-i.MX6 ULL";
+ compatible = "phytec,imx6ull-pcl063", "fsl,imx6ull";
+};
+
+&iomuxc {
+ /delete-node/ gpioledssomgrp;
+};
+
+&iomuxc_snvs {
+ pinctrl_gpioleds_som: gpioledssomgrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 PHYTEC Messtechnik GmbH
+ * Author: Stefan Riedmueller <s.riedmueller@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ull-phytec-phycore-som.dtsi"
+#include "imx6ull-phytec-segin.dtsi"
+#include "imx6ull-phytec-segin-peb-eval-01.dtsi"
+
+/ {
+ model = "PHYTEC phyBOARD-Segin i.MX6 ULL Full Featured with eMMC";
+ compatible = "phytec,imx6ull-pbacd10-emmc", "phytec,imx6ull-pbacd10",
+ "phytec,imx6ull-pcl063","fsl,imx6ull";
+};
+
+&adc1 {
+ status = "okay";
+};
+
+&can1 {
+ status = "okay";
+};
+
+&tlv320 {
+ status = "okay";
+};
+
+&ecspi3 {
+ status = "okay";
+};
+
+ðphy1 {
+ status = "okay";
+};
+
+ðphy2 {
+ status = "okay";
+};
+
+&fec1 {
+ status = "okay";
+};
+
+&fec2 {
+ status = "okay";
+};
+
+&i2c_rtc {
+ status = "okay";
+};
+
+®_can1_en {
+ status = "okay";
+};
+
+®_sound_1v8 {
+ status = "okay";
+};
+
+®_sound_3v3 {
+ status = "okay";
+};
+
+&sai2 {
+ status = "okay";
+};
+
+&sound {
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&usbotg1 {
+ status = "okay";
+};
+
+&usbotg2 {
+ status = "okay";
+};
+
+&usdhc1 {
+ status = "okay";
+};
+
+&usdhc2 {
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 PHYTEC Messtechnik GmbH
+ * Author: Stefan Riedmueller <s.riedmueller@phytec.de>
+ */
+
+#include "imx6ul-phytec-segin-peb-eval-01.dtsi"
+
+&iomuxc {
+ /delete-node/ gpio_keysgrp;
+};
+
+&iomuxc_snvs {
+ pinctrl_gpio_keys: gpio_keysgrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x79
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 PHYTEC Messtechnik GmbH
+ * Author: Stefan Riedmueller <s.riedmueller@phytec.de>
+ */
+
+#include "imx6ul-phytec-segin.dtsi"
+
+/ {
+ model = "PHYTEC phyBOARD-Segin i.MX6 ULL";
+ compatible = "phytec,imx6ull-pbacd-10", "phytec,imx6ull-pcl063","fsl,imx6ull";
+};
+
+&iomuxc {
+ /delete-node/ flexcan1engrp;
+ /delete-node/ rtcintgrp;
+ /delete-node/ stmpegrp;
+};
+
+&iomuxc_snvs {
+ princtrl_flexcan1_en: flexcan1engrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x17059
+ >;
+ };
+
+ pinctrl_rtc_int: rtcintgrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x17059
+ >;
+ };
+
+ pinctrl_stmpe: stmpegrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x17059
+ >;
+ };
+};
rn5t567@33 {
compatible = "ricoh,rn5t567";
reg = <0x33>;
+
+ regulators {
+ reg_DCDC1: DCDC1 { /* V1.0_SOC */
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_DCDC2: DCDC2 { /* V1.1_ARM */
+ regulator-min-microvolt = <975000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_DCDC3: DCDC3 { /* V1.8 */
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_DCDC4: DCDC4 { /* V1.35_DRAM */
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_LDO1: LDO1 { /* PWR_EN_+V3.3_ETH */
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ reg_LDO2: LDO2 { /* +V1.8_SD */
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_LDO3: LDO3 { /* PWR_EN_+V3.3_LPSR */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_LDO4: LDO4 { /* V1.8_LPSR */
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_LDO5: LDO5 { /* PWR_EN_+V3.3 */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
};
};
status = "okay";
};
+&fec1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pinctrl_enet1>;
+ pinctrl-1 = <&pinctrl_enet1_sleep>;
+ clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET1_TIME_ROOT_CLK>,
+ <&clks IMX7D_PLL_ENET_MAIN_50M_CLK>;
+ clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
+ assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+ <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+ assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+ assigned-clock-rates = <0>, <100000000>;
+ phy-mode = "rmii";
+ phy-supply = <®_LDO1>;
+ fsl,magic-packet;
+ status = "okay";
+};
+
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1>;
MX7D_PAD_SD1_DATA3__SD1_DATA3 0x59
>;
};
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX7D_PAD_ENET1_CRS__GPIO7_IO14 0x14
+ MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x73
+ MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x73
+ MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x73
+ MX7D_PAD_ENET1_RGMII_RXC__ENET1_RX_ER 0x73
+
+ MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x73
+ MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x73
+ MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x73
+ MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1 0x73
+ MX7D_PAD_SD2_CD_B__ENET1_MDIO 0x3
+ MX7D_PAD_SD2_WP__ENET1_MDC 0x3
+ >;
+ };
+
+ pinctrl_enet1_sleep: enet1sleepgrp {
+ fsl,pins = <
+ MX7D_PAD_ENET1_RGMII_RX_CTL__GPIO7_IO4 0x0
+ MX7D_PAD_ENET1_RGMII_RD0__GPIO7_IO0 0x0
+ MX7D_PAD_ENET1_RGMII_RD1__GPIO7_IO1 0x0
+ MX7D_PAD_ENET1_RGMII_RXC__GPIO7_IO5 0x0
+
+ MX7D_PAD_ENET1_RGMII_TX_CTL__GPIO7_IO10 0x0
+ MX7D_PAD_ENET1_RGMII_TD0__GPIO7_IO6 0x0
+ MX7D_PAD_ENET1_RGMII_TD1__GPIO7_IO7 0x0
+ MX7D_PAD_GPIO1_IO12__GPIO1_IO12 0x0
+ MX7D_PAD_SD2_CD_B__GPIO5_IO9 0x0
+ MX7D_PAD_SD2_WP__GPIO5_IO10 0x0
+ >;
+ };
};
&iomuxc_lpsr {
--- /dev/null
+&fec2 {
+ status = "disable";
+};
model = "Freescale i.MX7 SabreSD Board";
compatible = "fsl,imx7d-sdb", "fsl,imx7d";
- aliases {
- spi5 = &soft_spi;
+ chosen {
+ stdout-path = &uart1;
};
- memory {
+ memory@80000000 {
+ device_type = "memory";
reg = <0x80000000 0x80000000>;
};
- soft_spi: soft-spi {
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ volume-up {
+ label = "Volume Up";
+ gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ wakeup-source;
+ };
+
+ volume-down {
+ label = "Volume Down";
+ gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ wakeup-source;
+ };
+ };
+
+ spi4 {
compatible = "spi-gpio";
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_spi1>;
- status = "okay";
- gpio-sck = <&gpio1 13 0>;
- gpio-mosi = <&gpio1 9 0>;
- cs-gpios = <&gpio1 12 0>;
+ pinctrl-0 = <&pinctrl_spi4>;
+ gpio-sck = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ gpio-mosi = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ cs-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
num-chipselects = <1>;
#address-cells = <1>;
#size-cells = <0>;
- gpio_spi: gpio_spi@0 {
+ extended_io: gpio-expander@0 {
compatible = "fairchild,74hc595";
gpio-controller;
#gpio-cells = <2>;
reg = <0>;
registers-number = <1>;
- registers-default = /bits/ 8 <0x74>; /* Enable PERI_3V3, SENSOR_RST_B and HDMI_RST*/
spi-max-frequency = <100000>;
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
+ reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
- reg_usb_otg1_vbus: regulator@0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "usb_otg1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
+ reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg2_vbus";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg2_vbus_reg>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
- reg_usb_otg2_vbus: regulator@1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "usb_otg2_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- reg_sd1_vmmc: regulator@3 {
- compatible = "regulator-fixed";
- regulator-name = "VDD_SD1";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
- startup-delay-us = <200000>;
- enable-active-high;
- };
+ reg_vref_1v8: regulator-vref-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
-};
-&iomuxc {
- imx7d-sdb {
- pinctrl_spi1: spi1grp {
- fsl,pins = <
- MX7D_PAD_GPIO1_IO09__GPIO1_IO9 0x59
- MX7D_PAD_GPIO1_IO12__GPIO1_IO12 0x59
- MX7D_PAD_GPIO1_IO13__GPIO1_IO13 0x59
- >;
- };
+ reg_brcm: regulator-brcm {
+ compatible = "regulator-fixed";
+ gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-name = "brcm_reg";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_brcm_reg>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <200000>;
+ };
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX7D_PAD_I2C1_SDA__I2C1_SDA 0x4000007f
- MX7D_PAD_I2C1_SCL__I2C1_SCL 0x4000007f
- >;
- };
+ reg_lcd_3v3: regulator-lcd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&extended_io 7 GPIO_ACTIVE_LOW>;
+ };
- pinctrl_i2c2: i2c2grp {
- fsl,pins = <
- MX7D_PAD_I2C2_SDA__I2C2_SDA 0x4000007f
- MX7D_PAD_I2C2_SCL__I2C2_SCL 0x4000007f
- >;
- };
+ reg_can2_3v3: regulator-can2-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "can2-3v3";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2_reg>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 14 GPIO_ACTIVE_LOW>;
+ };
- pinctrl_i2c3: i2c3grp {
- fsl,pins = <
- MX7D_PAD_I2C3_SDA__I2C3_SDA 0x4000007f
- MX7D_PAD_I2C3_SCL__I2C3_SCL 0x4000007f
- >;
- };
+ reg_fec2_3v3: regulator-fec2-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "fec2-3v3";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2_reg>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ };
- pinctrl_i2c4: i2c4grp {
- fsl,pins = <
- MX7D_PAD_SAI1_RX_BCLK__I2C4_SDA 0x4000007f
- MX7D_PAD_SAI1_RX_SYNC__I2C4_SCL 0x4000007f
- >;
- };
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000 0>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ status = "okay";
+ };
- pinctrl_usdhc1_gpio: usdhc1_gpiogrp {
- fsl,pins = <
- MX7D_PAD_SD1_CD_B__GPIO5_IO0 0x59 /* CD */
- MX7D_PAD_SD1_WP__GPIO5_IO1 0x59 /* WP */
- MX7D_PAD_SD1_RESET_B__GPIO5_IO2 0x59 /* vmmc */
- MX7D_PAD_GPIO1_IO08__SD1_VSELECT 0x59 /* VSELECT */
- >;
- };
+ panel {
+ compatible = "innolux,at043tn24";
+ backlight = <&backlight>;
+ power-supply = <®_lcd_3v3>;
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX7D_PAD_SD1_CMD__SD1_CMD 0x59
- MX7D_PAD_SD1_CLK__SD1_CLK 0x19
- MX7D_PAD_SD1_DATA0__SD1_DATA0 0x59
- MX7D_PAD_SD1_DATA1__SD1_DATA1 0x59
- MX7D_PAD_SD1_DATA2__SD1_DATA2 0x59
- MX7D_PAD_SD1_DATA3__SD1_DATA3 0x59
- >;
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
};
+ };
+};
- pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
- fsl,pins = <
- MX7D_PAD_SD1_CMD__SD1_CMD 0x5a
- MX7D_PAD_SD1_CLK__SD1_CLK 0x1a
- MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5a
- MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5a
- MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5a
- MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5a
- >;
- };
+&adc1 {
+ vref-supply = <®_vref_1v8>;
+ status = "okay";
+};
- pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
- fsl,pins = <
- MX7D_PAD_SD1_CMD__SD1_CMD 0x5b
- MX7D_PAD_SD1_CLK__SD1_CLK 0x1b
- MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5b
- MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5b
- MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5b
- MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5b
- >;
- };
+&adc2 {
+ vref-supply = <®_vref_1v8>;
+ status = "okay";
+};
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX7D_PAD_SD2_CMD__SD2_CMD 0x59
- MX7D_PAD_SD2_CLK__SD2_CLK 0x19
- MX7D_PAD_SD2_DATA0__SD2_DATA0 0x59
- MX7D_PAD_SD2_DATA1__SD2_DATA1 0x59
- MX7D_PAD_SD2_DATA2__SD2_DATA2 0x59
- MX7D_PAD_SD2_DATA3__SD2_DATA3 0x59
- MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21 0x19 /* WL_REG_ON */
- MX7D_PAD_ECSPI2_SCLK__GPIO4_IO20 0x19 /* WL_HOST_WAKE */
- >;
- };
+&cpu0 {
+ cpu-supply = <&sw1a_reg>;
+};
- pinctrl_usdhc2_100mhz: usdhc2grp_100mhz {
- fsl,pins = <
- MX7D_PAD_SD2_CMD__SD2_CMD 0x5a
- MX7D_PAD_SD2_CLK__SD2_CLK 0x1a
- MX7D_PAD_SD2_DATA0__SD2_DATA0 0x5a
- MX7D_PAD_SD2_DATA1__SD2_DATA1 0x5a
- MX7D_PAD_SD2_DATA2__SD2_DATA2 0x5a
- MX7D_PAD_SD2_DATA3__SD2_DATA3 0x5a
- >;
- };
+&ecspi3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ cs-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ status = "okay";
- pinctrl_usdhc2_200mhz: usdhc2grp_200mhz {
- fsl,pins = <
- MX7D_PAD_SD2_CMD__SD2_CMD 0x5b
- MX7D_PAD_SD2_CLK__SD2_CLK 0x1b
- MX7D_PAD_SD2_DATA0__SD2_DATA0 0x5b
- MX7D_PAD_SD2_DATA1__SD2_DATA1 0x5b
- MX7D_PAD_SD2_DATA2__SD2_DATA2 0x5b
- MX7D_PAD_SD2_DATA3__SD2_DATA3 0x5b
- >;
- };
+ tsc2046@0 {
+ compatible = "ti,tsc2046";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ pinctrl-names ="default";
+ pinctrl-0 = <&pinctrl_tsc2046_pendown>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <29 0>;
+ pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+ ti,x-min = /bits/ 16 <0>;
+ ti,x-max = /bits/ 16 <0>;
+ ti,y-min = /bits/ 16 <0>;
+ ti,y-max = /bits/ 16 <0>;
+ ti,pressure-max = /bits/ 16 <0>;
+ ti,x-plate-ohms = /bits/ 16 <400>;
+ wakeup-source;
+ };
+};
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <
- MX7D_PAD_SD3_CMD__SD3_CMD 0x59
- MX7D_PAD_SD3_CLK__SD3_CLK 0x19
- MX7D_PAD_SD3_DATA0__SD3_DATA0 0x59
- MX7D_PAD_SD3_DATA1__SD3_DATA1 0x59
- MX7D_PAD_SD3_DATA2__SD3_DATA2 0x59
- MX7D_PAD_SD3_DATA3__SD3_DATA3 0x59
- MX7D_PAD_SD3_DATA4__SD3_DATA4 0x59
- MX7D_PAD_SD3_DATA5__SD3_DATA5 0x59
- MX7D_PAD_SD3_DATA6__SD3_DATA6 0x59
- MX7D_PAD_SD3_DATA7__SD3_DATA7 0x59
- MX7D_PAD_SD3_STROBE__SD3_STROBE 0x19
- >;
- };
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+ <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+ assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+ assigned-clock-rates = <0>, <100000000>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+ phy-reset-gpios = <&extended_io 5 GPIO_ACTIVE_LOW>;
+ status = "okay";
- pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
- fsl,pins = <
- MX7D_PAD_SD3_CMD__SD3_CMD 0x5a
- MX7D_PAD_SD3_CLK__SD3_CLK 0x1a
- MX7D_PAD_SD3_DATA0__SD3_DATA0 0x5a
- MX7D_PAD_SD3_DATA1__SD3_DATA1 0x5a
- MX7D_PAD_SD3_DATA2__SD3_DATA2 0x5a
- MX7D_PAD_SD3_DATA3__SD3_DATA3 0x5a
- MX7D_PAD_SD3_DATA4__SD3_DATA4 0x5a
- MX7D_PAD_SD3_DATA5__SD3_DATA5 0x5a
- MX7D_PAD_SD3_DATA6__SD3_DATA6 0x5a
- MX7D_PAD_SD3_DATA7__SD3_DATA7 0x5a
- MX7D_PAD_SD3_STROBE__SD3_STROBE 0x1a
- >;
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
};
- pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
- fsl,pins = <
- MX7D_PAD_SD3_CMD__SD3_CMD 0x5b
- MX7D_PAD_SD3_CLK__SD3_CLK 0x1b
- MX7D_PAD_SD3_DATA0__SD3_DATA0 0x5b
- MX7D_PAD_SD3_DATA1__SD3_DATA1 0x5b
- MX7D_PAD_SD3_DATA2__SD3_DATA2 0x5b
- MX7D_PAD_SD3_DATA3__SD3_DATA3 0x5b
- MX7D_PAD_SD3_DATA4__SD3_DATA4 0x5b
- MX7D_PAD_SD3_DATA5__SD3_DATA5 0x5b
- MX7D_PAD_SD3_DATA6__SD3_DATA6 0x5b
- MX7D_PAD_SD3_DATA7__SD3_DATA7 0x5b
- MX7D_PAD_SD3_STROBE__SD3_STROBE 0x1b
- >;
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
};
};
};
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ assigned-clocks = <&clks IMX7D_ENET2_TIME_ROOT_SRC>,
+ <&clks IMX7D_ENET2_TIME_ROOT_CLK>;
+ assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+ assigned-clock-rates = <0>, <100000000>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy1>;
+ phy-supply = <®_fec2_3v3>;
+ fsl,magic-packet;
+ status = "okay";
+};
+
+&flexcan2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ xceiver-supply = <®_can2_3v3>;
+ status = "okay";
+};
+
&i2c1 {
- clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
- pmic: pfuze3000@08 {
+ pmic: pfuze3000@8 {
compatible = "fsl,pfuze3000";
reg = <0x08>;
regulators {
sw1a_reg: sw1a {
regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <3300000>;
+ regulator-max-microvolt = <1475000>;
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <6250>;
};
sw2_reg: sw2 {
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1850000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
regulator-boot-on;
regulator-always-on;
};
vgen2_reg: vldo2 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1550000>;
- regulator-always-on;
};
vgen3_reg: vccsd {
};
vgen6_reg: vldo4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
regulator-always-on;
};
};
};
&i2c2 {
- clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
+
+ mpl3115@60 {
+ compatible = "fsl,mpl3115";
+ reg = <0x60>;
+ };
};
&i2c3 {
- clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
};
&i2c4 {
- clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c4>;
status = "okay";
+
+ codec: wm8960@1a {
+ compatible = "wlf,wm8960";
+ reg = <0x1a>;
+ clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+ clock-names = "mclk";
+ wlf,shared-lrclk;
+ };
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcdif>;
+ status = "okay";
+
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
+ assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
+ status = "okay";
+};
+
+&uart6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart6>;
+ assigned-clocks = <&clks IMX7D_UART6_ROOT_SRC>;
+ assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <®_usb_otg1_vbus>;
+ status = "okay";
+};
+
+&usbotg2 {
+ vbus-supply = <®_usb_otg2_vbus>;
+ dr_mode = "host";
+ status = "okay";
};
&usdhc1 {
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>;
- pinctrl-1 = <&pinctrl_usdhc1_100mhz>, <&pinctrl_usdhc1_gpio>;
- pinctrl-2 = <&pinctrl_usdhc1_200mhz>, <&pinctrl_usdhc1_gpio>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
- vmmc-supply = <®_sd1_vmmc>;
- fsl,tuning-start-tap = <20>;
- fsl,tuning-step= <2>;
+ wakeup-source;
+ keep-power-in-suspend;
status = "okay";
};
pinctrl-0 = <&pinctrl_usdhc2>;
pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ wakeup-source;
+ keep-power-in-suspend;
non-removable;
- fsl,tuning-start-tap = <20>;
- fsl,tuning-step= <2>;
+ vmmc-supply = <®_brcm>;
+ fsl,tuning-step = <2>;
status = "okay";
};
pinctrl-0 = <&pinctrl_usdhc3>;
pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
+ assigned-clock-rates = <400000000>;
bus-width = <8>;
+ fsl,tuning-step = <2>;
non-removable;
- fsl,tuning-start-tap = <20>;
- fsl,tuning-step= <2>;
status = "okay";
};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ imx7d-sdb {
+ pinctrl_brcm_reg: brcmreggrp {
+ fsl,pins = <
+ MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21 0x14
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX7D_PAD_SAI2_TX_SYNC__ECSPI3_MISO 0x2
+ MX7D_PAD_SAI2_TX_BCLK__ECSPI3_MOSI 0x2
+ MX7D_PAD_SAI2_RX_DATA__ECSPI3_SCLK 0x2
+ MX7D_PAD_SD2_CD_B__GPIO5_IO9 0x59
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO10__ENET1_MDIO 0x3
+ MX7D_PAD_GPIO1_IO11__ENET1_MDC 0x3
+ MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC 0x1
+ MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x1
+ MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x1
+ MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 0x1
+ MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 0x1
+ MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x1
+ MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC 0x1
+ MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x1
+ MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x1
+ MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 0x1
+ MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 0x1
+ MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x1
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC 0x1
+ MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0 0x1
+ MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1 0x1
+ MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2 0x1
+ MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3 0x1
+ MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL 0x1
+ MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC 0x1
+ MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0 0x1
+ MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1 0x1
+ MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2 0x1
+ MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3 0x1
+ MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL 0x1
+ >;
+ };
+
+ pinctrl_enet2_reg: enet2reggrp {
+ fsl,pins = <
+ MX7D_PAD_LPSR_GPIO1_IO04__GPIO1_IO4 0x14
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX 0x59
+ MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX 0x59
+ >;
+ };
+
+ pinctrl_flexcan2_reg: flexcan2reggrp {
+ fsl,pins = <
+ MX7D_PAD_EPDC_DATA14__GPIO2_IO14 0x59 /* CAN_STBY */
+ >;
+ };
+
+ pinctrl_gpio_keys: gpio_keysgrp {
+ fsl,pins = <
+ MX7D_PAD_SD2_RESET_B__GPIO5_IO11 0x59
+ MX7D_PAD_SD2_WP__GPIO5_IO10 0x59
+ >;
+ };
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ MX7D_PAD_ECSPI2_SS0__GPIO4_IO23 0x34 /* bt reg on */
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX7D_PAD_I2C1_SDA__I2C1_SDA 0x4000007f
+ MX7D_PAD_I2C1_SCL__I2C1_SCL 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX7D_PAD_I2C2_SDA__I2C2_SDA 0x4000007f
+ MX7D_PAD_I2C2_SCL__I2C2_SCL 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX7D_PAD_I2C3_SDA__I2C3_SDA 0x4000007f
+ MX7D_PAD_I2C3_SCL__I2C3_SCL 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX7D_PAD_SAI1_RX_BCLK__I2C4_SDA 0x4000007f
+ MX7D_PAD_SAI1_RX_SYNC__I2C4_SCL 0x4000007f
+ >;
+ };
+
+ pinctrl_lcdif: lcdifgrp {
+ fsl,pins = <
+ MX7D_PAD_LCD_DATA00__LCD_DATA0 0x79
+ MX7D_PAD_LCD_DATA01__LCD_DATA1 0x79
+ MX7D_PAD_LCD_DATA02__LCD_DATA2 0x79
+ MX7D_PAD_LCD_DATA03__LCD_DATA3 0x79
+ MX7D_PAD_LCD_DATA04__LCD_DATA4 0x79
+ MX7D_PAD_LCD_DATA05__LCD_DATA5 0x79
+ MX7D_PAD_LCD_DATA06__LCD_DATA6 0x79
+ MX7D_PAD_LCD_DATA07__LCD_DATA7 0x79
+ MX7D_PAD_LCD_DATA08__LCD_DATA8 0x79
+ MX7D_PAD_LCD_DATA09__LCD_DATA9 0x79
+ MX7D_PAD_LCD_DATA10__LCD_DATA10 0x79
+ MX7D_PAD_LCD_DATA11__LCD_DATA11 0x79
+ MX7D_PAD_LCD_DATA12__LCD_DATA12 0x79
+ MX7D_PAD_LCD_DATA13__LCD_DATA13 0x79
+ MX7D_PAD_LCD_DATA14__LCD_DATA14 0x79
+ MX7D_PAD_LCD_DATA15__LCD_DATA15 0x79
+ MX7D_PAD_LCD_DATA16__LCD_DATA16 0x79
+ MX7D_PAD_LCD_DATA17__LCD_DATA17 0x79
+ MX7D_PAD_LCD_DATA18__LCD_DATA18 0x79
+ MX7D_PAD_LCD_DATA19__LCD_DATA19 0x79
+ MX7D_PAD_LCD_DATA20__LCD_DATA20 0x79
+ MX7D_PAD_LCD_DATA21__LCD_DATA21 0x79
+ MX7D_PAD_LCD_DATA22__LCD_DATA22 0x79
+ MX7D_PAD_LCD_DATA23__LCD_DATA23 0x79
+ MX7D_PAD_LCD_CLK__LCD_CLK 0x79
+ MX7D_PAD_LCD_ENABLE__LCD_ENABLE 0x79
+ MX7D_PAD_LCD_VSYNC__LCD_VSYNC 0x79
+ MX7D_PAD_LCD_HSYNC__LCD_HSYNC 0x79
+ MX7D_PAD_LCD_RESET__LCD_RESET 0x79
+ >;
+ };
+
+ pinctrl_spi4: spi4grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO09__GPIO1_IO9 0x59
+ MX7D_PAD_GPIO1_IO12__GPIO1_IO12 0x59
+ MX7D_PAD_GPIO1_IO13__GPIO1_IO13 0x59
+ >;
+ };
+
+ pinctrl_tsc2046_pendown: tsc2046_pendown {
+ fsl,pins = <
+ MX7D_PAD_EPDC_BDR1__GPIO2_IO29 0x59
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX 0x79
+ MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX 0x79
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX7D_PAD_SAI1_TX_BCLK__UART5_DCE_TX 0x79
+ MX7D_PAD_SAI1_RX_DATA__UART5_DCE_RX 0x79
+ MX7D_PAD_SAI1_TX_SYNC__UART5_DCE_CTS 0x79
+ MX7D_PAD_SAI1_TX_DATA__UART5_DCE_RTS 0x79
+ >;
+ };
+
+ pinctrl_uart6: uart6grp {
+ fsl,pins = <
+ MX7D_PAD_ECSPI1_MOSI__UART6_DCE_TX 0x79
+ MX7D_PAD_ECSPI1_SCLK__UART6_DCE_RX 0x79
+ MX7D_PAD_ECSPI1_SS0__UART6_DCE_CTS 0x79
+ MX7D_PAD_ECSPI1_MISO__UART6_DCE_RTS 0x79
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX7D_PAD_SD1_CMD__SD1_CMD 0x59
+ MX7D_PAD_SD1_CLK__SD1_CLK 0x19
+ MX7D_PAD_SD1_DATA0__SD1_DATA0 0x59
+ MX7D_PAD_SD1_DATA1__SD1_DATA1 0x59
+ MX7D_PAD_SD1_DATA2__SD1_DATA2 0x59
+ MX7D_PAD_SD1_DATA3__SD1_DATA3 0x59
+ MX7D_PAD_SD1_CD_B__GPIO5_IO0 0x59 /* CD */
+ MX7D_PAD_SD1_WP__GPIO5_IO1 0x59 /* WP */
+ MX7D_PAD_SD1_RESET_B__GPIO5_IO2 0x59 /* vmmc */
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX7D_PAD_SD2_CMD__SD2_CMD 0x59
+ MX7D_PAD_SD2_CLK__SD2_CLK 0x19
+ MX7D_PAD_SD2_DATA0__SD2_DATA0 0x59
+ MX7D_PAD_SD2_DATA1__SD2_DATA1 0x59
+ MX7D_PAD_SD2_DATA2__SD2_DATA2 0x59
+ MX7D_PAD_SD2_DATA3__SD2_DATA3 0x59
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp_100mhz {
+ fsl,pins = <
+ MX7D_PAD_SD2_CMD__SD2_CMD 0x5a
+ MX7D_PAD_SD2_CLK__SD2_CLK 0x1a
+ MX7D_PAD_SD2_DATA0__SD2_DATA0 0x5a
+ MX7D_PAD_SD2_DATA1__SD2_DATA1 0x5a
+ MX7D_PAD_SD2_DATA2__SD2_DATA2 0x5a
+ MX7D_PAD_SD2_DATA3__SD2_DATA3 0x5a
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp_200mhz {
+ fsl,pins = <
+ MX7D_PAD_SD2_CMD__SD2_CMD 0x5b
+ MX7D_PAD_SD2_CLK__SD2_CLK 0x1b
+ MX7D_PAD_SD2_DATA0__SD2_DATA0 0x5b
+ MX7D_PAD_SD2_DATA1__SD2_DATA1 0x5b
+ MX7D_PAD_SD2_DATA2__SD2_DATA2 0x5b
+ MX7D_PAD_SD2_DATA3__SD2_DATA3 0x5b
+ >;
+ };
+
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX7D_PAD_SD3_CMD__SD3_CMD 0x59
+ MX7D_PAD_SD3_CLK__SD3_CLK 0x19
+ MX7D_PAD_SD3_DATA0__SD3_DATA0 0x59
+ MX7D_PAD_SD3_DATA1__SD3_DATA1 0x59
+ MX7D_PAD_SD3_DATA2__SD3_DATA2 0x59
+ MX7D_PAD_SD3_DATA3__SD3_DATA3 0x59
+ MX7D_PAD_SD3_DATA4__SD3_DATA4 0x59
+ MX7D_PAD_SD3_DATA5__SD3_DATA5 0x59
+ MX7D_PAD_SD3_DATA6__SD3_DATA6 0x59
+ MX7D_PAD_SD3_DATA7__SD3_DATA7 0x59
+ MX7D_PAD_SD3_STROBE__SD3_STROBE 0x19
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
+ fsl,pins = <
+ MX7D_PAD_SD3_CMD__SD3_CMD 0x5a
+ MX7D_PAD_SD3_CLK__SD3_CLK 0x1a
+ MX7D_PAD_SD3_DATA0__SD3_DATA0 0x5a
+ MX7D_PAD_SD3_DATA1__SD3_DATA1 0x5a
+ MX7D_PAD_SD3_DATA2__SD3_DATA2 0x5a
+ MX7D_PAD_SD3_DATA3__SD3_DATA3 0x5a
+ MX7D_PAD_SD3_DATA4__SD3_DATA4 0x5a
+ MX7D_PAD_SD3_DATA5__SD3_DATA5 0x5a
+ MX7D_PAD_SD3_DATA6__SD3_DATA6 0x5a
+ MX7D_PAD_SD3_DATA7__SD3_DATA7 0x5a
+ MX7D_PAD_SD3_STROBE__SD3_STROBE 0x1a
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
+ fsl,pins = <
+ MX7D_PAD_SD3_CMD__SD3_CMD 0x5b
+ MX7D_PAD_SD3_CLK__SD3_CLK 0x1b
+ MX7D_PAD_SD3_DATA0__SD3_DATA0 0x5b
+ MX7D_PAD_SD3_DATA1__SD3_DATA1 0x5b
+ MX7D_PAD_SD3_DATA2__SD3_DATA2 0x5b
+ MX7D_PAD_SD3_DATA3__SD3_DATA3 0x5b
+ MX7D_PAD_SD3_DATA4__SD3_DATA4 0x5b
+ MX7D_PAD_SD3_DATA5__SD3_DATA5 0x5b
+ MX7D_PAD_SD3_DATA6__SD3_DATA6 0x5b
+ MX7D_PAD_SD3_DATA7__SD3_DATA7 0x5b
+ MX7D_PAD_SD3_STROBE__SD3_STROBE 0x1b
+ >;
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&iomuxc_lpsr {
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX7D_PAD_LPSR_GPIO1_IO00__WDOG1_WDOG_B 0x74
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX7D_PAD_LPSR_GPIO1_IO01__PWM1_OUT 0x30
+ >;
+ };
+
+ pinctrl_usb_otg2_vbus_reg: usbotg2vbusreggrp {
+ fsl,pins = <
+ MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7 0x14
+ >;
+ };
+};
#include "imx7s.dtsi"
/ {
+ aliases {
+ ethernet1 = &fec2;
+ };
cpus {
cpu0: cpu@0 {
operating-points = <
spi2 = &ecspi2;
spi3 = &ecspi3;
spi4 = &ecspi4;
+ ethernet0 = &fec1;
};
cpus {
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright 2019 NXP
+// Author: Fabio Estevam <fabio.estevam@nxp.com>
+
+/dts-v1/;
+
+#include "imx7ulp.dtsi"
+
+/ {
+ model = "Embedded Artists i.MX7ULP COM";
+ compatible = "ea,imx7ulp-com", "fsl,imx7ulp";
+
+ chosen {
+ stdout-path = &lpuart4;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x60000000 0x8000000>;
+ };
+};
+
+&lpuart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart4>;
+ status = "okay";
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg1_id>;
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ status = "okay";
+};
+
+&usbphy1 {
+ fsl,tx-d-cal = <88>;
+};
+
+&usdhc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc0>;
+ non-removable;
+ bus-width = <8>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&iomuxc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog_1>;
+
+ pinctrl_hog_1: hoggrp-1 {
+ fsl,pins = <
+ IMX7ULP_PAD_PTC1__PTC1 0x20000
+ >;
+ };
+
+ pinctrl_lpuart4: lpuart4grp {
+ fsl,pins = <
+ IMX7ULP_PAD_PTC3__LPUART4_RX 0x3
+ IMX7ULP_PAD_PTC2__LPUART4_TX 0x3
+ >;
+ };
+
+ pinctrl_usdhc0: usdhc0grp {
+ fsl,pins = <
+ IMX7ULP_PAD_PTD1__SDHC0_CMD 0x43
+ IMX7ULP_PAD_PTD2__SDHC0_CLK 0x10042
+ IMX7ULP_PAD_PTD3__SDHC0_D7 0x43
+ IMX7ULP_PAD_PTD4__SDHC0_D6 0x43
+ IMX7ULP_PAD_PTD5__SDHC0_D5 0x43
+ IMX7ULP_PAD_PTD6__SDHC0_D4 0x43
+ IMX7ULP_PAD_PTD7__SDHC0_D3 0x43
+ IMX7ULP_PAD_PTD8__SDHC0_D2 0x43
+ IMX7ULP_PAD_PTD9__SDHC0_D1 0x43
+ IMX7ULP_PAD_PTD10__SDHC0_D0 0x43
+ IMX7ULP_PAD_PTD11__SDHC0_DQS 0x42
+ >;
+ };
+
+ pinctrl_usbotg1_id: otg1idgrp {
+ fsl,pins = <
+ IMX7ULP_PAD_PTC13__USB0_ID 0x10003
+ >;
+ };
+};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2018 Collabora Ltd.
- *
- * Based on dts[i] from Phytec barebox port:
- * Copyright (C) 2016 PHYTEC Messtechnik GmbH
- * Author: Christian Hemp <c.hemp@phytec.de>
- */
-
-/ {
- model = "Phytec phyCORE-i.MX6 Ultra Lite SOM";
- compatible = "phytec,imx6ul-pcl063", "fsl,imx6ul";
-
- memory {
- reg = <0x80000000 0x20000000>;
- };
-
- chosen {
- stdout-path = &uart1;
- };
-};
-
-&fec1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet1>;
- phy-mode = "rmii";
- phy-handle = <ðphy0>;
- status = "okay";
-
- mdio: mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy0: ethernet-phy@1 {
- reg = <1>;
- micrel,led-mode = <1>;
- };
- };
-};
-
-&gpmi {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpmi_nand>;
- nand-on-flash-bbt;
- fsl,no-blockmark-swap;
- status = "disabled";
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "uboot";
- reg = <0x0 0x400000>;
- };
-
- partition@400000 {
- label = "uboot-env";
- reg = <0x400000 0x100000>;
- };
-
- partition@500000 {
- label = "root";
- reg = <0x500000 0x0>;
- };
-};
-
-&i2c1 {
- clock-frequency = <100000>;
- pinctrl-names = "default", "gpio";
- pinctrl-0 = <&pinctrl_i2c1>;
- pinctrl-1 = <&pinctrl_i2c1_gpio>;
- scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
- sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
- status = "okay";
-
- eeprom@52 {
- compatible = "cat,24c32";
- reg = <0x52>;
- };
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&usdhc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc1>;
- cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
- bus-width = <0x4>;
- pinctrl-0 = <&pinctrl_usdhc1>;
- no-1-8-v;
- status = "okay";
-};
-
-&usdhc2 {
- u-boot,dm-spl;
- u-boot,dm-pre-reloc;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc2>;
- bus-width = <8>;
- no-1-8-v;
- non-removable;
- keep-power-in-suspend;
- status = "disabled";
-};
-
-&iomuxc {
- pinctrl-names = "default";
-
- pinctrl_enet1: enet1grp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
- MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
- MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
- MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
- MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
- MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
- MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
- MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
- MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
- MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
- >;
- };
-
- pinctrl_gpmi_nand: gpminandgrp {
- fsl,pins = <
- MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1
- MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1
- MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1
- MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000
- MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1
- MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1
- MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1
- MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1
- MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1
- MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1
- MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1
- MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1
- MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1
- MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1
- MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1
- >;
- };
-
- pinctrl_i2c1: i2cgrp {
- fsl,pins = <
- MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
- MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
- >;
- };
-
- pinctrl_i2c1_gpio: i2c1grp_gpio {
- fsl,pins = <
- MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0
- MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0
- >;
- };
-
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
- MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
- >;
- };
-
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
- MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
- MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
- MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
- MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
- MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
- MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059
-
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
- MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
- MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
- MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
- MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
- MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
- MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9
- MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9
- MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9
- MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9
- MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170f9
- >;
- };
-};
extern struct dram_timing_info dram_timing;
void ddr_load_train_firmware(enum fw_type type);
-void ddr_init(struct dram_timing_info *timing_info);
-void ddr_cfg_phy(struct dram_timing_info *timing_info);
+int ddr_init(struct dram_timing_info *timing_info);
+int ddr_cfg_phy(struct dram_timing_info *timing_info);
void load_lpddr4_phy_pie(void);
void ddrphy_trained_csr_save(struct dram_cfg_param *param, unsigned int num);
void dram_config_save(struct dram_timing_info *info, unsigned long base);
/* utils function for ddr phy training */
-void wait_ddrphy_training_complete(void);
+int wait_ddrphy_training_complete(void);
void ddrphy_init_set_dfi_clk(unsigned int drate);
void ddrphy_init_read_msg_block(enum fw_type type);
mxs_reg_32(hw_clkctrl_xbus) /* 0x40 */
mxs_reg_32(hw_clkctrl_xtal) /* 0x50 */
mxs_reg_32(hw_clkctrl_pix) /* 0x60 */
- mxs_reg_32(hw_clkctrl_ssp0) /* 0x70 */
- mxs_reg_32(hw_clkctrl_gpmi) /* 0x80 */
+ uint32_t hw_clkctrl_ssp0; /* 0x70 */
+ uint32_t reserved_ssp0[3]; /* 0x74-0x7c */
+ uint32_t hw_clkctrl_gpmi; /* 0x80 */
+ uint32_t reserved_gpmi[3]; /* 0x84-0x8c */
mxs_reg_32(hw_clkctrl_spdif) /* 0x90 */
mxs_reg_32(hw_clkctrl_emi) /* 0xa0 */
mxs_reg_32(hw_clkctrl_hbus) /* 0x60 */
mxs_reg_32(hw_clkctrl_xbus) /* 0x70 */
mxs_reg_32(hw_clkctrl_xtal) /* 0x80 */
- mxs_reg_32(hw_clkctrl_ssp0) /* 0x90 */
- mxs_reg_32(hw_clkctrl_ssp1) /* 0xa0 */
- mxs_reg_32(hw_clkctrl_ssp2) /* 0xb0 */
- mxs_reg_32(hw_clkctrl_ssp3) /* 0xc0 */
- mxs_reg_32(hw_clkctrl_gpmi) /* 0xd0 */
+ uint32_t hw_clkctrl_ssp0; /* 0x90 */
+ uint32_t reserved_ssp0[3]; /* 0x94-0x9c */
+ uint32_t hw_clkctrl_ssp1; /* 0xa0 */
+ uint32_t reserved_ssp1[3]; /* 0xa4-0xac */
+ uint32_t hw_clkctrl_ssp2; /* 0xb0 */
+ uint32_t reserved_ssp2[3]; /* 0xb4-0xbc */
+ uint32_t hw_clkctrl_ssp3; /* 0xc0 */
+ uint32_t reserved_ssp3[3]; /* 0xc4-0xcc */
+ uint32_t hw_clkctrl_gpmi; /* 0xd0 */
+ uint32_t reserved_gpmi[3]; /* 0xd4-0xdc */
mxs_reg_32(hw_clkctrl_spdif) /* 0xe0 */
mxs_reg_32(hw_clkctrl_emi) /* 0xf0 */
mxs_reg_32(hw_clkctrl_saif0) /* 0x100 */
#endif /* CONFIG_MX6 */
+/* address translation table */
+struct rproc_att {
+ u32 da; /* device address (From Cortex M4 view) */
+ u32 sa; /* system bus address */
+ u32 size; /* size of reg range */
+};
+
#ifdef CONFIG_IMX8M
struct rom_api {
u16 ver;
"update addr off|partition len - update 'len' bytes starting at\n"
" 'off|part' to memory address 'addr', skipping bad blocks\n"
"bcbonly fw-size fw1-off [fw2-off] - write only BCB (FCB and DBBT)\n"
- " where `fw-size` is fw sizes in bytes, `fw1-off` and\n"
- " and `fw2-off` - firmware offsets ";
+ " where `fw-size` is fw sizes in bytes, `fw1-off`\n"
+ " and `fw2-off` - firmware offsets\n"
+ " FIY, BCB isn't erased automatically, so mtd erase should\n"
+ " be called in advance before writing new BCB:\n"
+ " > mtd erase mx7-bcb";
#endif
U_BOOT_CMD(nandbcb, 5, 1, do_nandbcb,
- "i.MX6 Nand BCB",
+ "i.MX6/i.MX7 NAND Boot Control Blocks write",
nandbcb_help_text
);
#include <asm/io.h>
#include <asm/mach-imx/sys_proto.h>
#include <command.h>
+#include <elf.h>
#include <imx_sip.h>
#include <linux/compiler.h>
+#include <cpu_func.h>
-int arch_auxiliary_core_up(u32 core_id, ulong boot_private_data)
+#ifndef CONFIG_IMX8M
+const __weak struct rproc_att hostmap[] = { };
+
+static const struct rproc_att *get_host_mapping(unsigned long auxcore)
+{
+ const struct rproc_att *mmap = hostmap;
+
+ while (mmap && mmap->size) {
+ if (mmap->da <= auxcore &&
+ mmap->da + mmap->size > auxcore)
+ return mmap;
+ mmap++;
+ }
+
+ return NULL;
+}
+
+/*
+ * A very simple elf loader, assumes the image is valid, returns the
+ * entry point address.
+ */
+static unsigned long load_elf_image_phdr(unsigned long addr)
+{
+ Elf32_Ehdr *ehdr; /* ELF header structure pointer */
+ Elf32_Phdr *phdr; /* Program header structure pointer */
+ int i;
+
+ ehdr = (Elf32_Ehdr *)addr;
+ phdr = (Elf32_Phdr *)(addr + ehdr->e_phoff);
+
+ /* Load each program header */
+ for (i = 0; i < ehdr->e_phnum; ++i, ++phdr) {
+ const struct rproc_att *mmap = get_host_mapping(phdr->p_paddr);
+ void *dst, *src;
+
+ if (phdr->p_type != PT_LOAD)
+ continue;
+
+ if (!mmap) {
+ printf("Invalid aux core address: %08x",
+ phdr->p_paddr);
+ return 0;
+ }
+
+ dst = (void *)(phdr->p_paddr - mmap->da) + mmap->sa;
+ src = (void *)addr + phdr->p_offset;
+
+ debug("Loading phdr %i to 0x%p (%i bytes)\n",
+ i, dst, phdr->p_filesz);
+
+ if (phdr->p_filesz)
+ memcpy(dst, src, phdr->p_filesz);
+ if (phdr->p_filesz != phdr->p_memsz)
+ memset(dst + phdr->p_filesz, 0x00,
+ phdr->p_memsz - phdr->p_filesz);
+ flush_cache((unsigned long)dst &
+ ~(CONFIG_SYS_CACHELINE_SIZE - 1),
+ ALIGN(phdr->p_filesz, CONFIG_SYS_CACHELINE_SIZE));
+ }
+
+ return ehdr->e_entry;
+}
+#endif
+
+int arch_auxiliary_core_up(u32 core_id, ulong addr)
{
ulong stack, pc;
- if (!boot_private_data)
+ if (!addr)
return -EINVAL;
- stack = *(u32 *)boot_private_data;
- pc = *(u32 *)(boot_private_data + 4);
+#ifdef CONFIG_IMX8M
+ stack = *(u32 *)addr;
+ pc = *(u32 *)(addr + 4);
+#else
+ /*
+ * handling ELF64 binaries
+ * isn't supported yet.
+ */
+ if (valid_elf_image(addr)) {
+ stack = 0x0;
+ pc = load_elf_image_phdr(addr);
+ if (!pc)
+ return CMD_RET_FAILURE;
+
+ } else {
+ /*
+ * Assume binary file with vector table at the beginning.
+ * Cortex-M4 vector tables start with the stack pointer (SP)
+ * and reset vector (initial PC).
+ */
+ stack = *(u32 *)addr;
+ pc = *(u32 *)(addr + 4);
+ }
+#endif
+ printf("## Starting auxiliary core stack = 0x%08lX, pc = 0x%08lX...\n",
+ stack, pc);
/* Set the stack and pc to M4 bootROM */
writel(stack, M4_BOOTROM_BASE_ADDR);
writel(pc, M4_BOOTROM_BASE_ADDR + 4);
+ flush_dcache_all();
+
/* Enable M4 */
#ifdef CONFIG_IMX8M
call_imx_sip(IMX_SIP_SRC, IMX_SIP_SRC_M4_START, 0, 0, 0);
addr = simple_strtoul(argv[1], NULL, 16);
- printf("## Starting auxiliary core at 0x%08lX ...\n", addr);
+ if (!addr)
+ return CMD_RET_FAILURE;
ret = arch_auxiliary_core_up(0, addr);
if (ret)
imply CMD_DM
imply CMD_SATA
-config TARGET_ARISTAINETOS
- bool "aristainetos"
-
config TARGET_ARISTAINETOS2
bool "aristainetos2"
select BOARD_LATE_INIT
+ select MX6DL
+ select SYS_I2C_MXC
+ select MXC_UART
+ select FEC_MXC
+ select DM
+ imply CMD_SATA
+ imply CMD_DM
config TARGET_ARISTAINETOS2B
bool "Support aristainetos2-revB"
select BOARD_LATE_INIT
+ select MX6DL
+ select SYS_I2C_MXC
+ select MXC_UART
+ select FEC_MXC
+ select DM
+ imply CMD_SATA
+ imply CMD_DM
+
+config TARGET_ARISTAINETOS2BCSL
+ bool "Support aristainetos2-revB CSL"
+ select BOARD_LATE_INIT
+ select MX6DL
+ select SYS_I2C_MXC
+ select MXC_UART
+ select FEC_MXC
+ select DM
+ imply CMD_SATA
+ imply CMD_DM
+
+config TARGET_ARISTAINETOS2C
+ bool "Support aristainetos2-revC"
+ select BOARD_LATE_INIT
+ select MX6DL
+ select SYS_I2C_MXC
+ select MXC_UART
+ select FEC_MXC
+ select DM
+ imply CMD_SATA
+ imply CMD_DM
config TARGET_CGTQMX6EVAL
bool "cgtqmx6eval"
writel(esdmisc_val, &mmdc0->mdref);
writel(zq_val, &mmdc0->mpzqhwctrl);
- debug("\tMMDC_MPWLDECTRL0 after write level cal: 0x%08X\n",
+ debug("\tMMDC_MPWLDECTRL0 after write level cal: 0x%08x\n",
readl(&mmdc0->mpwldectrl0));
- debug("\tMMDC_MPWLDECTRL1 after write level cal: 0x%08X\n",
+ debug("\tMMDC_MPWLDECTRL1 after write level cal: 0x%08x\n",
readl(&mmdc0->mpwldectrl1));
if (sysinfo->dsize == 2) {
- debug("\tMMDC_MPWLDECTRL0 after write level cal: 0x%08X\n",
+ debug("\tMMDC_MPWLDECTRL0 after write level cal: 0x%08x\n",
readl(&mmdc1->mpwldectrl0));
- debug("\tMMDC_MPWLDECTRL1 after write level cal: 0x%08X\n",
+ debug("\tMMDC_MPWLDECTRL1 after write level cal: 0x%08x\n",
readl(&mmdc1->mpwldectrl1));
}
return errors;
}
+static void mmdc_set_sdqs(bool set)
+{
+ struct mx6dq_iomux_ddr_regs *mx6dq_ddr_iomux =
+ (struct mx6dq_iomux_ddr_regs *)MX6DQ_IOM_DDR_BASE;
+ struct mx6sx_iomux_ddr_regs *mx6sx_ddr_iomux =
+ (struct mx6sx_iomux_ddr_regs *)MX6SX_IOM_DDR_BASE;
+ int i, sdqs_cnt;
+ u32 sdqs;
+
+ if (is_mx6sx()) {
+ sdqs = (u32)(&mx6sx_ddr_iomux->dram_sdqs0);
+ sdqs_cnt = 2;
+ } else { /* MX6DQ */
+ sdqs = (u32)(&mx6dq_ddr_iomux->dram_sdqs0);
+ sdqs_cnt = 8;
+ }
+
+ for (i = 0; i < sdqs_cnt; i++) {
+ if (set)
+ setbits_le32(sdqs + (4 * i), 0x7000);
+ else
+ clrbits_le32(sdqs + (4 * i), 0x7000);
+ }
+}
+
int mmdc_do_dqs_calibration(struct mx6_ddr_sysinfo const *sysinfo)
{
struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
struct mmdc_p_regs *mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR;
- struct mx6dq_iomux_ddr_regs *mx6_ddr_iomux =
- (struct mx6dq_iomux_ddr_regs *)MX6DQ_IOM_DDR_BASE;
bool cs0_enable;
bool cs1_enable;
bool cs0_enable_initial;
setbits_le32(&mmdc0->mapsr, 0x1);
/* set DQS pull ups */
- setbits_le32(&mx6_ddr_iomux->dram_sdqs0, 0x7000);
- setbits_le32(&mx6_ddr_iomux->dram_sdqs1, 0x7000);
- setbits_le32(&mx6_ddr_iomux->dram_sdqs2, 0x7000);
- setbits_le32(&mx6_ddr_iomux->dram_sdqs3, 0x7000);
- setbits_le32(&mx6_ddr_iomux->dram_sdqs4, 0x7000);
- setbits_le32(&mx6_ddr_iomux->dram_sdqs5, 0x7000);
- setbits_le32(&mx6_ddr_iomux->dram_sdqs6, 0x7000);
- setbits_le32(&mx6_ddr_iomux->dram_sdqs7, 0x7000);
+ mmdc_set_sdqs(true);
/* Save old RALAT and WALAT values */
esdmisc_val = readl(&mmdc0->mdmisc);
writel(esdmisc_val, &mmdc0->mdmisc);
/* Clear DQS pull ups */
- clrbits_le32(&mx6_ddr_iomux->dram_sdqs0, 0x7000);
- clrbits_le32(&mx6_ddr_iomux->dram_sdqs1, 0x7000);
- clrbits_le32(&mx6_ddr_iomux->dram_sdqs2, 0x7000);
- clrbits_le32(&mx6_ddr_iomux->dram_sdqs3, 0x7000);
- clrbits_le32(&mx6_ddr_iomux->dram_sdqs4, 0x7000);
- clrbits_le32(&mx6_ddr_iomux->dram_sdqs5, 0x7000);
- clrbits_le32(&mx6_ddr_iomux->dram_sdqs6, 0x7000);
- clrbits_le32(&mx6_ddr_iomux->dram_sdqs7, 0x7000);
+ mmdc_set_sdqs(false);
/* Re-enable SDE (chip selects) if they were set initially */
if (cs1_enable_initial)
*/
debug("MMDC registers updated from calibration\n");
debug("Read DQS gating calibration:\n");
- debug("\tMPDGCTRL0 PHY0 = 0x%08X\n", readl(&mmdc0->mpdgctrl0));
- debug("\tMPDGCTRL1 PHY0 = 0x%08X\n", readl(&mmdc0->mpdgctrl1));
+ debug("\tMPDGCTRL0 PHY0 = 0x%08x\n", readl(&mmdc0->mpdgctrl0));
+ debug("\tMPDGCTRL1 PHY0 = 0x%08x\n", readl(&mmdc0->mpdgctrl1));
if (sysinfo->dsize == 2) {
- debug("\tMPDGCTRL0 PHY1 = 0x%08X\n", readl(&mmdc1->mpdgctrl0));
- debug("\tMPDGCTRL1 PHY1 = 0x%08X\n", readl(&mmdc1->mpdgctrl1));
+ debug("\tMPDGCTRL0 PHY1 = 0x%08x\n", readl(&mmdc1->mpdgctrl0));
+ debug("\tMPDGCTRL1 PHY1 = 0x%08x\n", readl(&mmdc1->mpdgctrl1));
}
debug("Read calibration:\n");
- debug("\tMPRDDLCTL PHY0 = 0x%08X\n", readl(&mmdc0->mprddlctl));
+ debug("\tMPRDDLCTL PHY0 = 0x%08x\n", readl(&mmdc0->mprddlctl));
if (sysinfo->dsize == 2)
- debug("\tMPRDDLCTL PHY1 = 0x%08X\n", readl(&mmdc1->mprddlctl));
+ debug("\tMPRDDLCTL PHY1 = 0x%08x\n", readl(&mmdc1->mprddlctl));
debug("Write calibration:\n");
- debug("\tMPWRDLCTL PHY0 = 0x%08X\n", readl(&mmdc0->mpwrdlctl));
+ debug("\tMPWRDLCTL PHY0 = 0x%08x\n", readl(&mmdc0->mpwrdlctl));
if (sysinfo->dsize == 2)
- debug("\tMPWRDLCTL PHY1 = 0x%08X\n", readl(&mmdc1->mpwrdlctl));
+ debug("\tMPWRDLCTL PHY1 = 0x%08x\n", readl(&mmdc1->mpwrdlctl));
/*
* Registers below are for debugging purposes. These print out
#endif
}
+#ifdef CONFIG_IMX_BOOTAUX
+/*
+ * Table of mappings of physical mem regions in both
+ * Cortex-A7 and Cortex-M4 address spaces.
+ *
+ * For additional details check sections 2.1.2 and 2.1.3 in
+ * i.MX7Dual Applications Processor Reference Manual
+ *
+ */
+const struct rproc_att hostmap[] = {
+ /* aux core , host core, size */
+ { 0x00000000, 0x00180000, 0x8000 }, /* OCRAM_S */
+ { 0x00180000, 0x00180000, 0x8000 }, /* OCRAM_S */
+ { 0x20180000, 0x00180000, 0x8000 }, /* OCRAM_S */
+ { 0x1fff8000, 0x007f8000, 0x8000 }, /* TCML */
+ { 0x20000000, 0x00800000, 0x8000 }, /* TCMU */
+ { 0x00900000, 0x00900000, 0x20000 }, /* OCRAM_128KB */
+ { 0x20200000, 0x00900000, 0x20000 }, /* OCRAM_128KB */
+ { 0x00920000, 0x00920000, 0x20000 }, /* OCRAM_EPDC */
+ { 0x20220000, 0x00920000, 0x20000 }, /* OCRAM_EPDC */
+ { 0x00940000, 0x00940000, 0x20000 }, /* OCRAM_PXP */
+ { 0x20240000, 0x00940000, 0x20000 }, /* OCRAM_PXP */
+ { 0x10000000, 0x80000000, 0x0fff0000 }, /* DDR Code alias */
+ { 0x80000000, 0x80000000, 0xe0000000 }, /* DDRC */
+ { /* sentinel */ }
+};
+#endif
+
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
/* enable all periherial can be accessed in nosec mode */
static void init_csu(void)
prompt "MX7ULP board select"
optional
+config TARGET_MX7ULP_COM
+ bool "Support MX7ULP COM board"
+ select MX7ULP
+ select SYS_ARCH_TIMER
+
config TARGET_MX7ULP_EVK
bool "Support mx7ulp EVK board"
select MX7ULP
endchoice
+source "board/ea/mx7ulp_com/Kconfig"
source "board/freescale/mx7ulp_evk/Kconfig"
endif
config TARGET_TS4600
bool "Support TS4600"
+config TARGET_XEA
+ bool "Support XEA"
+
endchoice
config SYS_SOC
source "board/bluegiga/apx4devkit/Kconfig"
source "board/freescale/mx28evk/Kconfig"
+source "board/liebherr/xea/Kconfig"
source "board/ppcag/bg0900/Kconfig"
source "board/schulercontrol/sc_sps_1/Kconfig"
source "board/technologic/ts4600/Kconfig"
-if TARGET_ARISTAINETOS
+if TARGET_ARISTAINETOS2
+
+source "board/aristainetos/common/Kconfig"
config SYS_BOARD
default "aristainetos"
-config SYS_CONFIG_NAME
+config SYS_BOARD_VERSION
+ default 2
+
+endif
+
+if TARGET_ARISTAINETOS2B
+
+source "board/aristainetos/common/Kconfig"
+
+config SYS_BOARD
default "aristainetos"
+config SYS_BOARD_VERSION
+ default 3
+
endif
-if TARGET_ARISTAINETOS2
+if TARGET_ARISTAINETOS2BCSL
+
+source "board/aristainetos/common/Kconfig"
config SYS_BOARD
default "aristainetos"
-config SYS_CONFIG_NAME
- default "aristainetos2"
+config SYS_BOARD_VERSION
+ default 4
endif
-if TARGET_ARISTAINETOS2B
+if TARGET_ARISTAINETOS2C
+
+source "board/aristainetos/common/Kconfig"
config SYS_BOARD
default "aristainetos"
-config SYS_CONFIG_NAME
- default "aristainetos2b"
+config SYS_BOARD_VERSION
+ default 5
endif
M: Heiko Schocher <hs@denx.de>
S: Maintained
F: board/aristainetos/
-F: include/configs/aristainetos.h
-F: configs/aristainetos_defconfig
F: include/configs/aristainetos2.h
F: configs/aristainetos2_defconfig
F: configs/aristainetos2b_defconfig
+F: configs/aristainetos2bcsl_defconfig
+F: configs/aristainetos2c_defconfig
+F: arch/arm/dts/imx6qdl-aristainetos2.dtsi
+F: arch/arm/dts/imx6qdl-aristainetos2-common.dtsi
+F: arch/arm/dts/imx6qdl-aristainetos2-u-boot.dtsi
+F: arch/arm/dts/imx6dl-aristainetos2_7.dts
+F: arch/arm/dts/imx6dl-aristainetos2_7.dtsi
+F: arch/arm/dts/imx6dl-aristainetos2_7-u-boot.dtsi
+F: arch/arm/dts/imx6dl-aristainetos2_4.dts
+F: arch/arm/dts/imx6dl-aristainetos2_4.dtsi
+F: arch/arm/dts/imx6dl-aristainetos2_4-u-boot.dtsi
+F: arch/arm/dts/imx6dl-aristainetos2b_4.dts
+F: arch/arm/dts/imx6dl-aristainetos2b_4-u-boot.dtsi
+F: arch/arm/dts/imx6dl-aristainetos2b_7.dts
+F: arch/arm/dts/imx6dl-aristainetos2b_7-u-boot.dtsi
+F: arch/arm/dts/imx6qdl-aristainetos2b-u-boot.dtsi
+F: arch/arm/dts/imx6qdl-aristainetos2b.dtsi
+F: arch/arm/dts/imx6dl-aristainetos2b_csl_4.dts
+F: arch/arm/dts/imx6dl-aristainetos2b_csl_4-u-boot.dtsi
+F: arch/arm/dts/imx6dl-aristainetos2b_csl_7.dts
+F: arch/arm/dts/imx6dl-aristainetos2b_csl_7-u-boot.dtsi
+F: arch/arm/dts/imx6qdl-aristainetos2b_csl.dtsi
+F: arch/arm/dts/imx6qdl-aristainetos2b_csl-u-boot.dtsi
+F: arch/arm/dts/imx6dl-aristainetos2c_4.dts
+F: arch/arm/dts/imx6dl-aristainetos2c_4-u-boot.dtsi
+F: arch/arm/dts/imx6dl-aristainetos2c_7.dts
+F: arch/arm/dts/imx6dl-aristainetos2c_7-u-boot.dtsi
+F: arch/arm/dts/imx6qdl-aristainetos2c.dtsi
+F: arch/arm/dts/imx6qdl-aristainetos2c-u-boot.dtsi
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2015
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * Based on:
- * Copyright (C) 2012 Freescale Semiconductor, Inc.
- *
- * Author: Fabio Estevam <fabio.estevam@freescale.com>
- */
-
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-pins.h>
-#include <linux/errno.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <asm/mach-imx/video.h>
-#include <mmc.h>
-#include <fsl_esdhc_imx.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <asm/arch/mxc_hdmi.h>
-#include <asm/arch/crm_regs.h>
-#include <linux/fb.h>
-#include <ipu_pixfmt.h>
-#include <asm/io.h>
-#include <asm/arch/sys_proto.h>
-#include <pwm.h>
-
-struct i2c_pads_info i2c_pad_info3 = {
- .scl = {
- .i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC,
- .gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | PC,
- .gp = IMX_GPIO_NR(3, 17)
- },
- .sda = {
- .i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
- .gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
- .gp = IMX_GPIO_NR(3, 18)
- }
-};
-
-iomux_v3_cfg_t const uart1_pads[] = {
- MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const uart5_pads[] = {
- MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT15__UART5_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const gpio_pads[] = {
- /* LED enable */
- MX6_PAD_SD4_DAT5__GPIO2_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* spi flash WP protect */
- MX6_PAD_SD4_DAT7__GPIO2_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* backlight enable */
- MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* LED yellow */
- MX6_PAD_GPIO_3__GPIO1_IO03 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* LED red */
- MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* LED green */
- MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* LED blue */
- MX6_PAD_GPIO_6__GPIO1_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* i2c4 scl */
- MX6_PAD_GPIO_7__GPIO1_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* i2c4 sda */
- MX6_PAD_GPIO_8__GPIO1_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* spi CS 1 */
- MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const misc_pads[] = {
- MX6_PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* OTG Power enable */
- MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const enet_pads[] = {
- MX6_PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(0x4001b0a8),
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_RX_ER__ENET_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
-
-static void setup_iomux_enet(void)
-{
- struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
-
- imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
-
- /* set GPIO_16 as ENET_REF_CLK_OUT */
- setbits_le32(&iomux->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
-}
-
-static iomux_v3_cfg_t const backlight_pads[] = {
- MX6_PAD_GPIO_9__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_SD4_DAT1__PWM3_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const ecspi4_pads[] = {
- MX6_PAD_EIM_D21__ECSPI4_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_EIM_D22__ECSPI4_MISO | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_EIM_D28__ECSPI4_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_EIM_D20__GPIO3_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const display_pads[] = {
- MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK | MUX_PAD_CTRL(DISP_PAD_CTRL),
- MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15,
- MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02,
- MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03,
- MX6_PAD_DI0_PIN4__GPIO4_IO20,
- MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00,
- MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01,
- MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02,
- MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03,
- MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04,
- MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05,
- MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06,
- MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07,
- MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08,
- MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09,
- MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10,
- MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11,
- MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12,
- MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13,
- MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14,
- MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15,
- MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16,
- MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17,
- MX6_PAD_DISP0_DAT18__IPU1_DISP0_DATA18,
- MX6_PAD_DISP0_DAT19__IPU1_DISP0_DATA19,
- MX6_PAD_DISP0_DAT20__IPU1_DISP0_DATA20,
- MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21,
- MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22,
- MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23,
-};
-
-int board_spi_cs_gpio(unsigned bus, unsigned cs)
-{
- return (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS)
- ? (IMX_GPIO_NR(3, 20)) : -1;
-}
-
-static void setup_spi(void)
-{
- int i;
-
- imx_iomux_v3_setup_multiple_pads(ecspi4_pads, ARRAY_SIZE(ecspi4_pads));
- for (i = 0; i < 3; i++)
- enable_spi_clk(true, i);
-
- /* set cs1 to high */
- gpio_direction_output(ECSPI4_CS1, 1);
-}
-
-static void setup_iomux_uart(void)
-{
- imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
-}
-
-int board_eth_init(bd_t *bis)
-{
- struct iomuxc *iomuxc_regs =
- (struct iomuxc *)IOMUXC_BASE_ADDR;
- int ret;
-
- /* clear gpr1[14], gpr1[18:17] to select anatop clock */
- clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC_MASK, 0);
-
- ret = enable_fec_anatop_clock(0, ENET_50MHZ);
- if (ret)
- return ret;
-
- setup_iomux_enet();
- return cpu_eth_init(bis);
-}
-
-static void enable_lvds(struct display_info_t const *dev)
-{
- imx_iomux_v3_setup_multiple_pads(
- display_pads,
- ARRAY_SIZE(display_pads));
- imx_iomux_v3_setup_multiple_pads(
- backlight_pads,
- ARRAY_SIZE(backlight_pads));
-
- /* enable backlight PWM 3 */
- if (pwm_init(2, 0, 0))
- goto error;
- /* duty cycle 500ns, period: 3000ns */
- if (pwm_config(2, 500, 3000))
- goto error;
- if (pwm_enable(2))
- goto error;
- return;
-
-error:
- puts("error init pwm for backlight\n");
- return;
-}
-
-static void setup_display(void)
-{
- struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
- int reg;
-
- enable_ipu_clock();
-
- reg = readl(&mxc_ccm->cs2cdr);
- /* select pll 5 clock */
- reg &= MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK;
- reg &= MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK;
- writel(reg, &mxc_ccm->cs2cdr);
-
- imx_iomux_v3_setup_multiple_pads(backlight_pads,
- ARRAY_SIZE(backlight_pads));
-}
-
-static void setup_iomux_gpio(void)
-{
- imx_iomux_v3_setup_multiple_pads(gpio_pads, ARRAY_SIZE(gpio_pads));
-}
-
-int board_early_init_f(void)
-{
- setup_iomux_uart();
- setup_iomux_gpio();
-
- setup_display();
- return 0;
-}
-
-
-static void setup_i2c4(void)
-{
- /* i2c4 not used, set it to gpio input */
- gpio_request(IMX_GPIO_NR(1, 7), "i2c4_scl");
- gpio_direction_input(IMX_GPIO_NR(1, 7));
- gpio_request(IMX_GPIO_NR(1, 8), "i2c4_sda");
- gpio_direction_input(IMX_GPIO_NR(1, 8));
-}
-
-static void setup_board_gpio(void)
-{
- /* enable LED */
- gpio_request(IMX_GPIO_NR(2, 13), "LED ena");
- gpio_direction_output(IMX_GPIO_NR(2, 13), 0);
-
- gpio_request(IMX_GPIO_NR(1, 3), "LED yellow");
- gpio_direction_output(IMX_GPIO_NR(1, 3), 1);
- gpio_request(IMX_GPIO_NR(1, 4), "LED red");
- gpio_direction_output(IMX_GPIO_NR(1, 4), 1);
- gpio_request(IMX_GPIO_NR(1, 5), "LED green");
- gpio_direction_output(IMX_GPIO_NR(1, 5), 1);
- gpio_request(IMX_GPIO_NR(1, 6), "LED blue");
- gpio_direction_output(IMX_GPIO_NR(1, 6), 1);
-}
-
-static void setup_board_spi(void)
-{
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2015
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * Based on:
- * Copyright (C) 2012 Freescale Semiconductor, Inc.
- *
- * Author: Fabio Estevam <fabio.estevam@freescale.com>
- */
-
-#include <init.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-pins.h>
-#include <env.h>
-#include <linux/errno.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <asm/mach-imx/video.h>
-#include <mmc.h>
-#include <fsl_esdhc_imx.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <asm/arch/mxc_hdmi.h>
-#include <asm/arch/crm_regs.h>
-#include <linux/fb.h>
-#include <ipu_pixfmt.h>
-#include <asm/io.h>
-#include <asm/arch/sys_proto.h>
-#include <pwm.h>
-#include <micrel.h>
-#include <spi.h>
-#include <video.h>
-#include <../drivers/video/imx/ipu.h>
-#if defined(CONFIG_VIDEO_BMP_LOGO)
- #include <bmp_logo.h>
-#endif
-
-#define USDHC2_PAD_CTRL (PAD_CTL_SPEED_LOW | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#if (CONFIG_SYS_BOARD_VERSION == 2)
- /* 4.3 display controller */
- #define ECSPI1_CS0 IMX_GPIO_NR(4, 9)
- #define ECSPI4_CS0 IMX_GPIO_NR(3, 29)
-#elif (CONFIG_SYS_BOARD_VERSION == 3)
- #define ECSPI1_CS0 IMX_GPIO_NR(2, 30) /* NOR flash */
- /* 4.3 display controller */
- #define ECSPI1_CS1 IMX_GPIO_NR(4, 10)
-#endif
-
-#define SOFT_RESET_GPIO IMX_GPIO_NR(7, 13)
-#define SD2_DRIVER_ENABLE IMX_GPIO_NR(7, 8)
-
-struct i2c_pads_info i2c_pad_info3 = {
- .scl = {
- .i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | PC,
- .gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | PC,
- .gp = IMX_GPIO_NR(1, 5)
- },
- .sda = {
- .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC,
- .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | PC,
- .gp = IMX_GPIO_NR(1, 6)
- }
-};
-
-struct i2c_pads_info i2c_pad_info4 = {
- .scl = {
- .i2c_mode = MX6_PAD_GPIO_7__I2C4_SCL | PC,
- .gpio_mode = MX6_PAD_GPIO_7__GPIO1_IO07 | PC,
- .gp = IMX_GPIO_NR(1, 7)
- },
- .sda = {
- .i2c_mode = MX6_PAD_GPIO_8__I2C4_SDA | PC,
- .gpio_mode = MX6_PAD_GPIO_8__GPIO1_IO08 | PC,
- .gp = IMX_GPIO_NR(1, 8)
- }
-};
-
-iomux_v3_cfg_t const uart1_pads[] = {
- MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D19__UART1_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D20__UART1_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const uart2_pads[] = {
- MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const uart3_pads[] = {
- MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const uart4_pads[] = {
- MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const gpio_pads[] = {
- /* LED enable*/
- MX6_PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* LED yellow */
- MX6_PAD_NANDF_CS3__GPIO6_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* LED red */
-#if (CONFIG_SYS_BOARD_VERSION == 2)
- MX6_PAD_EIM_EB0__GPIO2_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
-#elif (CONFIG_SYS_BOARD_VERSION == 3)
- MX6_PAD_EIM_WAIT__GPIO5_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
-#endif
- /* LED green */
- MX6_PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* LED blue */
- MX6_PAD_EIM_EB1__GPIO2_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* spi flash WP protect */
- MX6_PAD_SD4_DAT7__GPIO2_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* spi CS 0 */
- MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* spi bus #2 SS driver enable */
- MX6_PAD_EIM_A23__GPIO6_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* RST_LOC# PHY reset input (has pull-down!)*/
- MX6_PAD_GPIO_18__GPIO7_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* SD 2 level shifter output enable */
- MX6_PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* SD1 card detect input */
- MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* SD1 write protect input */
- MX6_PAD_DI0_PIN4__GPIO4_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* SD2 card detect input */
- MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* SD2 write protect input */
- MX6_PAD_SD4_DAT2__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* Touchscreen IRQ */
- MX6_PAD_SD4_DAT1__GPIO2_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const misc_pads[] = {
- /* USB_OTG_ID = GPIO1_24*/
- MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* H1 Power enable = GPIO1_0*/
- MX6_PAD_GPIO_0__USB_H1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* OTG Power enable = GPIO4_15*/
- MX6_PAD_KEY_ROW4__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const enet_pads[] = {
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const backlight_pads[] = {
- /* backlight PWM brightness control */
- MX6_PAD_GPIO_9__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* backlight enable */
- MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* LCD power enable */
- MX6_PAD_NANDF_CS2__GPIO6_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const ecspi1_pads[] = {
- MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
-#if (CONFIG_SYS_BOARD_VERSION == 2)
- MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(SPI_PAD_CTRL),
-#elif (CONFIG_SYS_BOARD_VERSION == 3)
- MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_KEY_COL2__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
-#endif
-};
-
-static void setup_iomux_enet(void)
-{
- imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
-}
-
-#if (CONFIG_SYS_BOARD_VERSION == 2)
-iomux_v3_cfg_t const ecspi4_pads[] = {
- MX6_PAD_EIM_D21__ECSPI4_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_EIM_D22__ECSPI4_MISO | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_EIM_D28__ECSPI4_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-#endif
-
-static iomux_v3_cfg_t const display_pads[] = {
- MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK | MUX_PAD_CTRL(DISP_PAD_CTRL),
- MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15,
- MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02,
- MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03,
- MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00,
- MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01,
- MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02,
- MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03,
- MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04,
- MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05,
- MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06,
- MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07,
- MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08,
- MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09,
- MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10,
- MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11,
- MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12,
- MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13,
- MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14,
- MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15,
- MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16,
- MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17,
- MX6_PAD_DISP0_DAT18__IPU1_DISP0_DATA18,
- MX6_PAD_DISP0_DAT19__IPU1_DISP0_DATA19,
- MX6_PAD_DISP0_DAT20__IPU1_DISP0_DATA20,
- MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21,
- MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22,
- MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23,
-};
-
-int board_spi_cs_gpio(unsigned bus, unsigned cs)
-{
- if (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS)
-#if (CONFIG_SYS_BOARD_VERSION == 2)
- return IMX_GPIO_NR(5, 2);
-
- if (bus == 0 && cs == 0)
- return IMX_GPIO_NR(4, 9);
-#elif (CONFIG_SYS_BOARD_VERSION == 3)
- return ECSPI1_CS0;
-
- if (bus == 0 && cs == 1)
- return ECSPI1_CS1;
-#endif
- return -1;
-}
-
-static void setup_spi(void)
-{
- int i;
-
- imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
-
-#if (CONFIG_SYS_BOARD_VERSION == 2)
- imx_iomux_v3_setup_multiple_pads(ecspi4_pads, ARRAY_SIZE(ecspi4_pads));
-#endif
-
- for (i = 0; i < 4; i++)
- enable_spi_clk(true, i);
-
- gpio_direction_output(ECSPI1_CS0, 1);
-#if (CONFIG_SYS_BOARD_VERSION == 2)
- gpio_direction_output(ECSPI4_CS1, 0);
- /* set cs0 to high (second device on spi bus #4) */
- gpio_direction_output(ECSPI4_CS0, 1);
-#elif (CONFIG_SYS_BOARD_VERSION == 3)
- gpio_direction_output(ECSPI1_CS1, 1);
-#endif
-}
-
-static void setup_iomux_uart(void)
-{
- switch (CONFIG_MXC_UART_BASE) {
- case UART1_BASE:
- imx_iomux_v3_setup_multiple_pads(uart1_pads,
- ARRAY_SIZE(uart1_pads));
- break;
- case UART2_BASE:
- imx_iomux_v3_setup_multiple_pads(uart2_pads,
- ARRAY_SIZE(uart2_pads));
- break;
- case UART3_BASE:
- imx_iomux_v3_setup_multiple_pads(uart3_pads,
- ARRAY_SIZE(uart3_pads));
- break;
- case UART4_BASE:
- imx_iomux_v3_setup_multiple_pads(uart4_pads,
- ARRAY_SIZE(uart4_pads));
- break;
- }
-}
-
-int board_phy_config(struct phy_device *phydev)
-{
- /* control data pad skew - devaddr = 0x02, register = 0x04 */
- ksz9031_phy_extended_write(phydev, 0x02,
- MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
- MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
- /* rx data pad skew - devaddr = 0x02, register = 0x05 */
- ksz9031_phy_extended_write(phydev, 0x02,
- MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
- MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
- /* tx data pad skew - devaddr = 0x02, register = 0x06 */
- ksz9031_phy_extended_write(phydev, 0x02,
- MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
- MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
- /* gtx and rx clock pad skew - devaddr = 0x02, register = 0x08 */
- ksz9031_phy_extended_write(phydev, 0x02,
- MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
- MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x03FF);
-
- if (phydev->drv->config)
- phydev->drv->config(phydev);
-
- return 0;
-}
-
-int board_eth_init(bd_t *bis)
-{
- setup_iomux_enet();
- return cpu_eth_init(bis);
-}
-
-static int rotate_logo_one(unsigned char *out, unsigned char *in)
-{
- int i, j;
-
- for (i = 0; i < BMP_LOGO_WIDTH; i++)
- for (j = 0; j < BMP_LOGO_HEIGHT; j++)
- out[j * BMP_LOGO_WIDTH + BMP_LOGO_HEIGHT - 1 - i] =
- in[i * BMP_LOGO_WIDTH + j];
- return 0;
-}
-
-/*
- * Rotate the BMP_LOGO (only)
- * Will only work, if the logo is square, as
- * BMP_LOGO_HEIGHT and BMP_LOGO_WIDTH are defines, not variables
- */
-void rotate_logo(int rotations)
-{
- unsigned char out_logo[BMP_LOGO_WIDTH * BMP_LOGO_HEIGHT];
- unsigned char *in_logo;
- int i, j;
-
- if (BMP_LOGO_WIDTH != BMP_LOGO_HEIGHT)
- return;
-
- in_logo = bmp_logo_bitmap;
-
- /* one 90 degree rotation */
- if (rotations == 1 || rotations == 2 || rotations == 3)
- rotate_logo_one(out_logo, in_logo);
-
- /* second 90 degree rotation */
- if (rotations == 2 || rotations == 3)
- rotate_logo_one(in_logo, out_logo);
-
- /* third 90 degree rotation */
- if (rotations == 3)
- rotate_logo_one(out_logo, in_logo);
-
- /* copy result back to original array */
- if (rotations == 1 || rotations == 3)
- for (i = 0; i < BMP_LOGO_WIDTH; i++)
- for (j = 0; j < BMP_LOGO_HEIGHT; j++)
- in_logo[i * BMP_LOGO_WIDTH + j] =
- out_logo[i * BMP_LOGO_WIDTH + j];
-}
-
-static void enable_display_power(void)
-{
- imx_iomux_v3_setup_multiple_pads(backlight_pads,
- ARRAY_SIZE(backlight_pads));
-
- /* backlight enable */
- gpio_direction_output(IMX_GPIO_NR(6, 31), 1);
- /* LCD power enable */
- gpio_direction_output(IMX_GPIO_NR(6, 15), 1);
-
- /* enable backlight PWM 1 */
- if (pwm_init(0, 0, 0))
- goto error;
- /* duty cycle 500ns, period: 3000ns */
- if (pwm_config(0, 50000, 300000))
- goto error;
- if (pwm_enable(0))
- goto error;
- return;
-
-error:
- puts("error init pwm for backlight\n");
- return;
-}
-
-static void enable_lvds(struct display_info_t const *dev)
-{
- struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
- struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
- int reg;
- s32 timeout = 100000;
-
- /* set PLL5 clock */
- reg = readl(&ccm->analog_pll_video);
- reg |= BM_ANADIG_PLL_VIDEO_POWERDOWN;
- writel(reg, &ccm->analog_pll_video);
-
- /* set PLL5 to 232720000Hz */
- reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
- reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x26);
- reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
- reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0);
- writel(reg, &ccm->analog_pll_video);
-
- writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xC0238),
- &ccm->analog_pll_video_num);
- writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xF4240),
- &ccm->analog_pll_video_denom);
-
- reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
- writel(reg, &ccm->analog_pll_video);
-
- while (timeout--)
- if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
- break;
- if (timeout < 0)
- printf("Warning: video pll lock timeout!\n");
-
- reg = readl(&ccm->analog_pll_video);
- reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
- reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
- writel(reg, &ccm->analog_pll_video);
-
- /* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */
- reg = readl(&ccm->cs2cdr);
- reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
- | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
- reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
- | (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
- writel(reg, &ccm->cs2cdr);
-
- reg = readl(&ccm->cscmr2);
- reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
- writel(reg, &ccm->cscmr2);
-
- reg = readl(&ccm->chsccdr);
- reg |= (CHSCCDR_CLK_SEL_LDB_DI0
- << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
- writel(reg, &ccm->chsccdr);
-
- reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
- | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
- | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH
- | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
- | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
- | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
- | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
- writel(reg, &iomux->gpr[2]);
-
- reg = readl(&iomux->gpr[3]);
- reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
- | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
- << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
- writel(reg, &iomux->gpr[3]);
-
- return;
-}
-
-static void enable_spi_display(struct display_info_t const *dev)
-{
- struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
- struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
- int reg;
- s32 timeout = 100000;
-
-#if defined(CONFIG_VIDEO_BMP_LOGO)
- rotate_logo(3); /* portrait display in landscape mode */
-#endif
-
- /*
- * set ldb clock to 28341000 Hz calculated through the formula:
- * (XRES + LEFT_M + RIGHT_M + HSYNC_LEN) *
- * (YRES + UPPER_M + LOWER_M + VSYNC_LEN) * REFRESH)
- * see:
- * https://community.freescale.com/thread/308170
- */
- ipu_set_ldb_clock(28341000);
-
- reg = readl(&ccm->cs2cdr);
-
- /* select pll 5 clock */
- reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
- | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
- writel(reg, &ccm->cs2cdr);
-
- /* set PLL5 to 197994996Hz */
- reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
- reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x21);
- reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
- reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0);
- writel(reg, &ccm->analog_pll_video);
-
- writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xfbf4),
- &ccm->analog_pll_video_num);
- writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xf4240),
- &ccm->analog_pll_video_denom);
-
- reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
- writel(reg, &ccm->analog_pll_video);
-
- while (timeout--)
- if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
- break;
- if (timeout < 0)
- printf("Warning: video pll lock timeout!\n");
-
- reg = readl(&ccm->analog_pll_video);
- reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
- reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
- writel(reg, &ccm->analog_pll_video);
-
- /* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */
- reg = readl(&ccm->cs2cdr);
- reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
- | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
- reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
- | (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
- writel(reg, &ccm->cs2cdr);
-
- reg = readl(&ccm->cscmr2);
- reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
- writel(reg, &ccm->cscmr2);
-
- reg = readl(&ccm->chsccdr);
- reg |= (CHSCCDR_CLK_SEL_LDB_DI0
- << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
- reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK;
- reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET);
- reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK;
- reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
- writel(reg, &ccm->chsccdr);
-
- reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
- | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
- | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH
- | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
- | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
- | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
- | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
- writel(reg, &iomux->gpr[2]);
-
- reg = readl(&iomux->gpr[3]);
- reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
- | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
- << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
- writel(reg, &iomux->gpr[3]);
-
- imx_iomux_v3_setup_multiple_pads(
- display_pads,
- ARRAY_SIZE(display_pads));
-
- return;
-}
-static void setup_display(void)
-{
- enable_ipu_clock();
- enable_display_power();
-}
-
-static void setup_iomux_gpio(void)
-{
- imx_iomux_v3_setup_multiple_pads(gpio_pads, ARRAY_SIZE(gpio_pads));
-}
-
-static void set_gpr_register(void)
-{
- struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
-
- writel(IOMUXC_GPR1_APP_CLK_REQ_N | IOMUXC_GPR1_PCIE_RDY_L23 |
- IOMUXC_GPR1_EXC_MON_SLVE |
- (2 << IOMUXC_GPR1_ADDRS0_OFFSET) |
- IOMUXC_GPR1_ACT_CS0,
- &iomuxc_regs->gpr[1]);
- writel(0x0, &iomuxc_regs->gpr[8]);
- writel(IOMUXC_GPR12_ARMP_IPG_CLK_EN | IOMUXC_GPR12_ARMP_AHB_CLK_EN |
- IOMUXC_GPR12_ARMP_ATB_CLK_EN | IOMUXC_GPR12_ARMP_APB_CLK_EN,
- &iomuxc_regs->gpr[12]);
-}
-
-int board_early_init_f(void)
-{
- setup_iomux_uart();
- setup_iomux_gpio();
-
- gpio_direction_output(SOFT_RESET_GPIO, 1);
- gpio_direction_output(SD2_DRIVER_ENABLE, 1);
- setup_display();
- set_gpr_register();
- return 0;
-}
-
-static void setup_i2c4(void)
-{
- setup_i2c(3, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
- &i2c_pad_info4);
-}
-
-static void setup_board_gpio(void)
-{
- /* enable all LEDs */
- gpio_request(IMX_GPIO_NR(2, 13), "LED ena"); /* 25 */
- gpio_direction_output(IMX_GPIO_NR(1, 25), 0);
-
- /* switch off Status LEDs */
-#if (CONFIG_SYS_BOARD_VERSION == 2)
- gpio_request(IMX_GPIO_NR(6, 16), "LED yellow"); /* 176 */
- gpio_direction_output(IMX_GPIO_NR(6, 16), 1);
- gpio_request(IMX_GPIO_NR(2, 28), "LED red"); /* 60 */
- gpio_direction_output(IMX_GPIO_NR(2, 28), 1);
- gpio_request(IMX_GPIO_NR(5, 4), "LED green"); /* 132 */
- gpio_direction_output(IMX_GPIO_NR(5, 4), 1);
- gpio_request(IMX_GPIO_NR(2, 29), "LED blue"); /* 61 */
- gpio_direction_output(IMX_GPIO_NR(2, 29), 1);
-#elif (CONFIG_SYS_BOARD_VERSION == 3)
- gpio_request(IMX_GPIO_NR(6, 16), "LED yellow"); /* 176 */
- gpio_direction_output(IMX_GPIO_NR(6, 16), 0);
- gpio_request(IMX_GPIO_NR(5, 0), "LED red"); /* 128 */
- gpio_direction_output(IMX_GPIO_NR(5, 0), 0);
- gpio_request(IMX_GPIO_NR(5, 4), "LED green"); /* 132 */
- gpio_direction_output(IMX_GPIO_NR(5, 4), 0);
- gpio_request(IMX_GPIO_NR(2, 29), "LED blue"); /* 61 */
- gpio_direction_output(IMX_GPIO_NR(2, 29), 0);
-#endif
-}
-
-static void setup_board_spi(void)
-{
- /* enable spi bus #2 SS drivers (and spi bus #4 SS1 for rev2b) */
- gpio_direction_output(IMX_GPIO_NR(6, 6), 1);
-}
-
-int board_late_init(void)
-{
- char *my_bootdelay;
- char bootmode = 0;
- char const *panel = env_get("panel");
-
- /*
- * Check the boot-source. If booting from NOR Flash,
- * disable bootdelay
- */
- gpio_request(IMX_GPIO_NR(7, 6), "bootsel0");
- gpio_direction_input(IMX_GPIO_NR(7, 6));
- gpio_request(IMX_GPIO_NR(7, 7), "bootsel1");
- gpio_direction_input(IMX_GPIO_NR(7, 7));
- gpio_request(IMX_GPIO_NR(7, 1), "bootsel2");
- gpio_direction_input(IMX_GPIO_NR(7, 1));
- bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 6)) ? 1 : 0) << 0;
- bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 7)) ? 1 : 0) << 1;
- bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 1)) ? 1 : 0) << 2;
-
- if (bootmode == 7) {
- my_bootdelay = env_get("nor_bootdelay");
- if (my_bootdelay != NULL)
- env_set("bootdelay", my_bootdelay);
- else
- env_set("bootdelay", "-2");
- }
-
- /* if we have the lg panel, we can initialze it now */
- if (panel)
- if (!strcmp(panel, displays[1].mode.name))
- lg4573_spi_startup(CONFIG_LG4573_BUS,
- CONFIG_LG4573_CS,
- 10000000, SPI_MODE_0);
-
- return 0;
-}
#include <asm/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/mxc_i2c.h>
#include <asm/mach-imx/video.h>
-#include <mmc.h>
-#include <fsl_esdhc_imx.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <asm/arch/mxc_hdmi.h>
#include <asm/arch/crm_regs.h>
-#include <linux/fb.h>
-#include <ipu_pixfmt.h>
-#include <input.h>
#include <asm/io.h>
#include <asm/arch/sys_proto.h>
-#include <pwm.h>
+#include <bmp_logo.h>
+#include <dm/root.h>
+#include <env.h>
+#include <i2c_eeprom.h>
+#include <i2c.h>
+#include <micrel.h>
+#include <miiphy.h>
+#include <lcd.h>
+#include <led.h>
+#include <splash.h>
+#include <video_fb.h>
DECLARE_GLOBAL_DATA_PTR;
-#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+enum {
+ BOARD_TYPE_4 = 4,
+ BOARD_TYPE_7 = 7,
+};
-#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
- PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+#define ARI_BT_4 "aristainetos2_4@2"
+#define ARI_BT_7 "aristainetos2_7@1"
-#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+int board_phy_config(struct phy_device *phydev)
+{
+ /* control data pad skew - devaddr = 0x02, register = 0x04 */
+ ksz9031_phy_extended_write(phydev, 0x02,
+ MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
+ MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+ /* rx data pad skew - devaddr = 0x02, register = 0x05 */
+ ksz9031_phy_extended_write(phydev, 0x02,
+ MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
+ MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+ /* tx data pad skew - devaddr = 0x02, register = 0x06 */
+ ksz9031_phy_extended_write(phydev, 0x02,
+ MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
+ MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+ /* gtx and rx clock pad skew - devaddr = 0x02, register = 0x08 */
+ ksz9031_phy_extended_write(phydev, 0x02,
+ MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
+ MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x03FF);
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
-#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+static int rotate_logo_one(unsigned char *out, unsigned char *in)
+{
+ int i, j;
-#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+ for (i = 0; i < BMP_LOGO_WIDTH; i++)
+ for (j = 0; j < BMP_LOGO_HEIGHT; j++)
+ out[j * BMP_LOGO_WIDTH + BMP_LOGO_HEIGHT - 1 - i] =
+ in[i * BMP_LOGO_WIDTH + j];
+ return 0;
+}
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/*
+ * Rotate the BMP_LOGO (only)
+ * Will only work, if the logo is square, as
+ * BMP_LOGO_HEIGHT and BMP_LOGO_WIDTH are defines, not variables
+ */
+void rotate_logo(int rotations)
+{
+ unsigned char out_logo[BMP_LOGO_WIDTH * BMP_LOGO_HEIGHT];
+ struct bmp_header *header;
+ unsigned char *in_logo;
+ int i, j;
+
+ if (BMP_LOGO_WIDTH != BMP_LOGO_HEIGHT)
+ return;
+
+ header = (struct bmp_header *)bmp_logo_bitmap;
+ in_logo = bmp_logo_bitmap + header->data_offset;
+
+ /* one 90 degree rotation */
+ if (rotations == 1 || rotations == 2 || rotations == 3)
+ rotate_logo_one(out_logo, in_logo);
+
+ /* second 90 degree rotation */
+ if (rotations == 2 || rotations == 3)
+ rotate_logo_one(in_logo, out_logo);
+
+ /* third 90 degree rotation */
+ if (rotations == 3)
+ rotate_logo_one(out_logo, in_logo);
+
+ /* copy result back to original array */
+ if (rotations == 1 || rotations == 3)
+ for (i = 0; i < BMP_LOGO_WIDTH; i++)
+ for (j = 0; j < BMP_LOGO_HEIGHT; j++)
+ in_logo[i * BMP_LOGO_WIDTH + j] =
+ out_logo[i * BMP_LOGO_WIDTH + j];
+}
-#define DISP_PAD_CTRL (0x10)
+static void enable_lvds(struct display_info_t const *dev)
+{
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ int reg;
+ s32 timeout = 100000;
+
+ /* set PLL5 clock */
+ reg = readl(&ccm->analog_pll_video);
+ reg |= BM_ANADIG_PLL_VIDEO_POWERDOWN;
+ writel(reg, &ccm->analog_pll_video);
+
+ /* set PLL5 to 232720000Hz */
+ reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
+ reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x26);
+ reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
+ reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0);
+ writel(reg, &ccm->analog_pll_video);
+
+ writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xC0238),
+ &ccm->analog_pll_video_num);
+ writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xF4240),
+ &ccm->analog_pll_video_denom);
+
+ reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
+ writel(reg, &ccm->analog_pll_video);
+
+ while (timeout--)
+ if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
+ break;
+ if (timeout < 0)
+ printf("Warning: video pll lock timeout!\n");
+
+ reg = readl(&ccm->analog_pll_video);
+ reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
+ reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
+ writel(reg, &ccm->analog_pll_video);
+
+ /* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */
+ reg = readl(&ccm->cs2cdr);
+ reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+ | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+ reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
+ | (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+ writel(reg, &ccm->cs2cdr);
+
+ reg = readl(&ccm->cscmr2);
+ reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
+ writel(reg, &ccm->cscmr2);
+
+ reg = readl(&ccm->chsccdr);
+ reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+ << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+ writel(reg, &ccm->chsccdr);
+
+ reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+ | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
+ | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH
+ | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+ | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
+ | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
+ | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
+ writel(reg, &iomux->gpr[2]);
+
+ reg = readl(&iomux->gpr[3]);
+ reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
+ | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+ << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
+ writel(reg, &iomux->gpr[3]);
+}
-#define ECSPI4_CS1 IMX_GPIO_NR(5, 2)
+static void enable_spi_display(struct display_info_t const *dev)
+{
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ int reg;
+ s32 timeout = 100000;
-#if (CONFIG_SYS_BOARD_VERSION == 1)
-#include "./aristainetos-v1.c"
-#elif ((CONFIG_SYS_BOARD_VERSION == 2) || (CONFIG_SYS_BOARD_VERSION == 3))
-#include "./aristainetos-v2.c"
+#if defined(CONFIG_VIDEO_BMP_LOGO)
+ rotate_logo(3); /* portrait display in landscape mode */
#endif
+ reg = readl(&ccm->cs2cdr);
+
+ /* select pll 5 clock */
+ reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+ | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+ writel(reg, &ccm->cs2cdr);
+
+ /* set PLL5 to 197994996Hz */
+ reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
+ reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x21);
+ reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
+ reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0);
+ writel(reg, &ccm->analog_pll_video);
+
+ writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xfbf4),
+ &ccm->analog_pll_video_num);
+ writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xf4240),
+ &ccm->analog_pll_video_denom);
+
+ reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
+ writel(reg, &ccm->analog_pll_video);
+
+ while (timeout--)
+ if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
+ break;
+ if (timeout < 0)
+ printf("Warning: video pll lock timeout!\n");
+
+ reg = readl(&ccm->analog_pll_video);
+ reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
+ reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
+ writel(reg, &ccm->analog_pll_video);
+
+ /* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */
+ reg = readl(&ccm->cs2cdr);
+ reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+ | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+ reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
+ | (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+ writel(reg, &ccm->cs2cdr);
+
+ reg = readl(&ccm->cscmr2);
+ reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
+ writel(reg, &ccm->cscmr2);
+
+ reg = readl(&ccm->chsccdr);
+ reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+ << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+ reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK;
+ reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET);
+ reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK;
+ reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
+ writel(reg, &ccm->chsccdr);
+
+ reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+ | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
+ | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH
+ | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+ | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
+ | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
+ | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
+ writel(reg, &iomux->gpr[2]);
+
+ reg = readl(&iomux->gpr[3]);
+ reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
+ | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+ << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
+ writel(reg, &iomux->gpr[3]);
+}
-struct i2c_pads_info i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | PC,
- .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | PC,
- .gp = IMX_GPIO_NR(5, 27)
- },
- .sda = {
- .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | PC,
- .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | PC,
- .gp = IMX_GPIO_NR(5, 26)
- }
-};
-
-struct i2c_pads_info i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | PC,
- .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | PC,
- .gp = IMX_GPIO_NR(4, 12)
- },
- .sda = {
- .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC,
- .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | PC,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
+static void setup_display(void)
+{
+ enable_ipu_clock();
+}
-iomux_v3_cfg_t const usdhc1_pads[] = {
- MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-};
+static void set_gpr_register(void)
+{
+ struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ writel(IOMUXC_GPR1_APP_CLK_REQ_N | IOMUXC_GPR1_PCIE_RDY_L23 |
+ IOMUXC_GPR1_EXC_MON_SLVE |
+ (2 << IOMUXC_GPR1_ADDRS0_OFFSET) |
+ IOMUXC_GPR1_ACT_CS0,
+ &iomuxc_regs->gpr[1]);
+ writel(0x0, &iomuxc_regs->gpr[8]);
+ writel(IOMUXC_GPR12_ARMP_IPG_CLK_EN | IOMUXC_GPR12_ARMP_AHB_CLK_EN |
+ IOMUXC_GPR12_ARMP_ATB_CLK_EN | IOMUXC_GPR12_ARMP_APB_CLK_EN,
+ &iomuxc_regs->gpr[12]);
+}
-int dram_init(void)
+extern char __bss_start[], __bss_end[];
+int board_early_init_f(void)
{
- gd->ram_size = imx_ddr_size();
+ select_ldb_di_clock_source(MXC_PLL5_CLK);
+ set_gpr_register();
+
+ /*
+ * clear bss here, so we can use spi driver
+ * before relocation and read Environment
+ * from spi flash.
+ */
+ memset(__bss_start, 0x00, __bss_end - __bss_start);
return 0;
}
-#ifdef CONFIG_FSL_ESDHC_IMX
-struct fsl_esdhc_cfg usdhc_cfg[2] = {
- {USDHC1_BASE_ADDR},
- {USDHC2_BASE_ADDR},
-};
+static void setup_one_led(char *label, int state)
+{
+ struct udevice *dev;
+ int ret;
+
+ ret = led_get_by_label(label, &dev);
+ if (ret == 0)
+ led_set_state(dev, state);
+}
+
+static void setup_board_gpio(void)
+{
+ setup_one_led("led_ena", LEDST_ON);
+ /* switch off Status LEDs */
+ setup_one_led("led_yellow", LEDST_OFF);
+ setup_one_led("led_red", LEDST_OFF);
+ setup_one_led("led_green", LEDST_OFF);
+ setup_one_led("led_blue", LEDST_OFF);
+}
+
+#define ARI_RESC_FMT "setenv rescue_reason setenv bootargs \\${bootargs}" \
+ " rescueReason=%d "
-int board_mmc_getcd(struct mmc *mmc)
+static void aristainetos_run_rescue_command(int reason)
{
- return 1;
+ char rescue_reason_command[80];
+
+ sprintf(rescue_reason_command, ARI_RESC_FMT, reason);
+ run_command(rescue_reason_command, 0);
}
-int board_mmc_init(bd_t *bis)
+static int aristainetos_eeprom(void)
+{
+ struct udevice *dev;
+ int off;
+ int ret;
+ u8 data[0x10];
+ u8 rescue_reason;
+
+ off = fdt_path_offset(gd->fdt_blob, "eeprom0");
+ if (off < 0) {
+ printf("%s: No eeprom0 path offset\n", __func__);
+ return off;
+ }
+
+ ret = uclass_get_device_by_of_offset(UCLASS_I2C_EEPROM, off, &dev);
+ if (ret) {
+ printf("%s: Could not find EEPROM\n", __func__);
+ return ret;
+ }
+
+ ret = i2c_set_chip_offset_len(dev, 2);
+ if (ret)
+ return ret;
+
+ ret = i2c_eeprom_read(dev, 0x1ff0, (uint8_t *)data, 6);
+ if (ret) {
+ printf("%s: Could not read EEPROM\n", __func__);
+ return ret;
+ }
+
+ if (strncmp((char *)&data[3], "ReScUe", 6) == 0) {
+ rescue_reason = *(uint8_t *)&data[9];
+ memset(&data[3], 0xff, 7);
+ i2c_eeprom_write(dev, 0x1ff0, (uint8_t *)&data[3], 7);
+ printf("\nBooting into Rescue System (EEPROM)\n");
+ aristainetos_run_rescue_command(rescue_reason);
+ run_command("run rescue_load_fit rescueboot", 0);
+ } else if (strncmp((char *)data, "DeF", 3) == 0) {
+ memset(data, 0xff, 3);
+ i2c_eeprom_write(dev, 0x1ff0, (uint8_t *)data, 3);
+ printf("\nClear u-boot environment (set back to defaults)\n");
+ run_command("run default_env; saveenv; saveenv", 0);
+ }
+
+ return 0;
+};
+
+static void aristainetos_bootmode_settings(void)
{
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
- imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
-#if (CONFIG_SYS_BOARD_VERSION == 2)
+ struct gpio_desc *desc;
+ struct src *psrc = (struct src *)SRC_BASE_ADDR;
+ unsigned int sbmr1 = readl(&psrc->sbmr1);
+ char *my_bootdelay;
+ char bootmode = 0;
+ int ret;
+
/*
- * usdhc2 has a levelshifter on the carrier board Rev. DV1,
- * that will automatically detect the driving direction.
- * During initialisation this isn't working correctly,
- * which causes DAT3 to be driven low towards the SD-card.
- * This causes a SD-card enetring the SPI-Mode
- * and therefore getting inaccessible until next power cycle.
- * As workaround we drive the DAT3 line as GPIO and set it high.
- * This makes usdhc2 unusable in u-boot, but works for the
- * initialisation in Linux
+ * Check the boot-source. If booting from NOR Flash,
+ * disable bootdelay
*/
- imx_iomux_v3_setup_pad(MX6_PAD_SD2_DAT3__GPIO1_IO12 |
- MUX_PAD_CTRL(NO_PAD_CTRL));
- gpio_direction_output(IMX_GPIO_NR(1, 12) , 1);
-#endif
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+ ret = gpio_hog_lookup_name("bootsel0", &desc);
+ if (!ret)
+ bootmode |= (dm_gpio_get_value(desc) ? 1 : 0) << 0;
+ ret = gpio_hog_lookup_name("bootsel1", &desc);
+ if (!ret)
+ bootmode |= (dm_gpio_get_value(desc) ? 1 : 0) << 1;
+ ret = gpio_hog_lookup_name("bootsel2", &desc);
+ if (!ret)
+ bootmode |= (dm_gpio_get_value(desc) ? 1 : 0) << 2;
+
+ if (bootmode == 7) {
+ my_bootdelay = env_get("nor_bootdelay");
+ if (my_bootdelay)
+ env_set("bootdelay", my_bootdelay);
+ else
+ env_set("bootdelay", "-2");
+ }
+
+ if (sbmr1 & 0x40) {
+ env_set("bootmode", "1");
+ printf("SD bootmode jumper set!\n");
+ } else {
+ env_set("bootmode", "0");
+ }
+
+ /* read out some jumper values*/
+ ret = gpio_hog_lookup_name("env_reset", &desc);
+ if (!ret) {
+ if (dm_gpio_get_value(desc)) {
+ printf("\nClear env (set back to defaults)\n");
+ run_command("run default_env; saveenv; saveenv", 0);
+ }
+ }
+ ret = gpio_hog_lookup_name("boot_rescue", &desc);
+ if (!ret) {
+ if (dm_gpio_get_value(desc)) {
+ aristainetos_run_rescue_command(16);
+ run_command("run rescue_xload_boot", 0);
+ }
+ }
}
-#endif
-/*
- * Do not overwrite the console
- * Use always serial for U-Boot console
- */
-int overwrite_console(void)
+int board_late_init(void)
+{
+ int x, y;
+
+ led_default_state();
+ splash_get_pos(&x, &y);
+ bmp_display((ulong)&bmp_logo_bitmap[0], x, y);
+
+ aristainetos_bootmode_settings();
+
+ /* eeprom work */
+ aristainetos_eeprom();
+
+ /* set board_type */
+ if (gd->board_type == BOARD_TYPE_4)
+ env_set("board_type", ARI_BT_4);
+ else
+ env_set("board_type", ARI_BT_7);
+
+ return 0;
+}
+
+int dram_init(void)
{
- return 1;
+ gd->ram_size = imx_ddr_size();
+
+ return 0;
}
struct display_info_t const displays[] = {
.vmode = FB_VMODE_NONINTERLACED
}
}
-#if ((CONFIG_SYS_BOARD_VERSION == 2) || (CONFIG_SYS_BOARD_VERSION == 3))
+#if ((CONFIG_SYS_BOARD_VERSION == 2) || \
+ (CONFIG_SYS_BOARD_VERSION == 3) || \
+ (CONFIG_SYS_BOARD_VERSION == 4) || \
+ (CONFIG_SYS_BOARD_VERSION == 5))
, {
.bus = -1,
.addr = 0,
};
size_t display_count = ARRAY_SIZE(displays);
-/* no console on this board */
-int board_cfb_skip(void)
-{
- return 1;
-}
-
+#if defined(CONFIG_NAND)
iomux_v3_cfg_t nfc_pads[] = {
MX6_PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NO_PAD_CTRL),
/* enable apbh clock gating */
setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
}
+#else
+static void setup_gpmi_nand(void)
+{
+}
+#endif
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
- setup_spi();
-
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
- &i2c_pad_info1);
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
- &i2c_pad_info2);
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
- &i2c_pad_info3);
- setup_i2c4();
-
- /* SPI NOR Flash read only */
- gpio_request(CONFIG_GPIO_ENABLE_SPI_FLASH, "ena_spi_nor");
- gpio_direction_output(CONFIG_GPIO_ENABLE_SPI_FLASH, 0);
- gpio_free(CONFIG_GPIO_ENABLE_SPI_FLASH);
-
setup_board_gpio();
setup_gpmi_nand();
- setup_board_spi();
+ setup_display();
/* GPIO_1 for USB_OTG_ID */
clrsetbits_le32(&iomux->gpr[1], IOMUXC_GPR1_USB_OTG_ID_SEL_MASK, 0);
- imx_iomux_v3_setup_multiple_pads(misc_pads, ARRAY_SIZE(misc_pads));
return 0;
}
-int checkboard(void)
+int board_fit_config_name_match(const char *name)
{
- printf("Board: %s\n", CONFIG_BOARDNAME);
- return 0;
+ if (gd->board_type == BOARD_TYPE_4 &&
+ strchr(name, 0x34))
+ return 0;
+
+ if (gd->board_type == BOARD_TYPE_7 &&
+ strchr(name, 0x37))
+ return 0;
+
+ return -1;
}
-#ifdef CONFIG_USB_EHCI_MX6
-int board_ehci_hcd_init(int port)
+static void do_board_detect(void)
{
int ret;
+ char s[30];
- ret = gpio_request(ARISTAINETOS_USB_H1_PWR, "usb-h1-pwr");
- if (!ret)
- gpio_direction_output(ARISTAINETOS_USB_H1_PWR, 1);
- ret = gpio_request(ARISTAINETOS_USB_OTG_PWR, "usb-OTG-pwr");
- if (!ret)
- gpio_direction_output(ARISTAINETOS_USB_OTG_PWR, 1);
- return 0;
+ /* default use board type 7 */
+ gd->board_type = BOARD_TYPE_7;
+ if (env_init())
+ return;
+
+ ret = env_get_f("panel", s, sizeof(s));
+ if (ret < 0)
+ return;
+
+ if (!strncmp("lg4573", s, 6))
+ gd->board_type = BOARD_TYPE_4;
}
-int board_ehci_power(int port, int on)
+#ifdef CONFIG_DTB_RESELECT
+int embedded_dtb_select(void)
{
- if (port)
- gpio_set_value(ARISTAINETOS_USB_OTG_PWR, on);
- else
- gpio_set_value(ARISTAINETOS_USB_H1_PWR, on);
+ int rescan;
+
+ do_board_detect();
+ fdtdec_resetup(&rescan);
+
return 0;
}
#endif
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2014
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * Based on:
- * Copyright (C) 2013 Boundary Devices
- *
- * Refer doc/README.imximage for more details about how-to configure
- * and create imximage boot image
- *
- * The syntax is taken as close as possible with the kwbimage
- */
-
-/* image version */
-IMAGE_VERSION 2
-
-/*
- * Boot Device : one of
- * spi, sd
- */
-BOOT_FROM spi
-
-#define __ASSEMBLY__
-#include <config.h>
-#include "asm/arch/mx6-ddr.h"
-#include "asm/arch/iomux.h"
-#include "asm/arch/crm_regs.h"
-
-#include "ddr-setup.cfg"
-#include "mt41j128M.cfg"
-#include "clocks.cfg"
#define __ASSEMBLY__
#include <config.h>
+#ifdef CONFIG_IMX_HAB
+CSF CONFIG_CSF_SIZE
+#endif
#include "asm/arch/mx6-ddr.h"
#include "asm/arch/iomux.h"
#include "asm/arch/crm_regs.h"
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2013 Boundary Devices
- *
- * Device Configuration Data (DCD)
- *
- * Each entry must have the format:
- * Addr-type Address Value
- *
- * where:
- * Addr-type register length (1,2 or 4 bytes)
- * Address absolute address of the register
- * value value to be stored in the register
- */
-
-/* set the default clock gate to save power */
-DATA 4, CCM_CCGR0, 0x00c03f3f
-DATA 4, CCM_CCGR1, 0x0030fcff
-DATA 4, CCM_CCGR2, 0x0fffcfc0
-DATA 4, CCM_CCGR3, 0x3ff0300f
-DATA 4, CCM_CCGR4, 0xfffff30c /* enable NAND/GPMI/BCH clocks */
-DATA 4, CCM_CCGR5, 0x0f0000c3
-DATA 4, CCM_CCGR6, 0x000003ff
--- /dev/null
+config SYS_BOARD_VERSION
+ int "select version of aristainetos board"
+ help
+ version of aristainetos board version
+ 2 version 2
+ 3 version 2b
+ 4 version 2bcsl
+ 5 version 2c
+
+config SYS_I2C_MXC_I2C1
+ default y
+
+config SYS_I2C_MXC_I2C2
+ default y
+
+config SYS_I2C_MXC_I2C3
+ default y
+
+config SYS_I2C_MXC_I2C4
+ default y
+
+config SYS_MALLOC_LEN
+ default 0x4000000
+
+config ENV_SIZE
+ default 0x3000
+
+config ENV_SECT_SIZE
+ default 0x10000
+
+config ENV_OFFSET
+ default 0xd0000
+
+config SYS_CONFIG_NAME
+ default "aristainetos2"
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2013 Boundary Devices
- *
- * Device Configuration Data (DCD)
- *
- * Each entry must have the format:
- * Addr-type Address Value
- *
- * where:
- * Addr-type register length (1,2 or 4 bytes)
- * Address absolute address of the register
- * value value to be stored in the register
- */
-
-/* DDR IO TYPE */
-DATA 4, MX6_IOM_GRP_DDR_TYPE, 0x000C0000
-DATA 4, MX6_IOM_GRP_DDRPKE, 0x00000000
-/* Clock */
-DATA 4, MX6_IOM_DRAM_SDCLK_0, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDCLK_1, 0x00000030
-/* Address */
-DATA 4, MX6_IOM_DRAM_CAS, 0x00000030
-DATA 4, MX6_IOM_DRAM_RAS, 0x00000030
-DATA 4, MX6_IOM_GRP_ADDDS, 0x00000030
-/* Control */
-DATA 4, MX6_IOM_DRAM_RESET, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDCKE0, 0x00003000
-DATA 4, MX6_IOM_DRAM_SDCKE1, 0x00003000
-DATA 4, MX6_IOM_DRAM_SDBA2, 0x00000000
-DATA 4, MX6_IOM_DRAM_SDODT0, 0x00003030
-DATA 4, MX6_IOM_DRAM_SDODT1, 0x00003030
-DATA 4, MX6_IOM_GRP_CTLDS, 0x00000030
-/* Data Strobe */
-DATA 4, MX6_IOM_DDRMODE_CTL, 0x00020000
-DATA 4, MX6_IOM_DRAM_SDQS0, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS1, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS2, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS3, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS4, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS5, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS6, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS7, 0x00000030
-DATA 4, MX6_IOM_GRP_DDRMODE, 0x00020000
-DATA 4, MX6_IOM_GRP_B0DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B1DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B2DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B3DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B4DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B5DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B6DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B7DS, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM0, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM1, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM2, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM3, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM4, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM5, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM6, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM7, 0x00000030
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2013 Boundary Devices
- */
-/* ZQ Calibration */
-DATA 4, MX6_MMDC_P0_MPZQHWCTRL, 0xa1390003
-DATA 4, MX6_MMDC_P1_MPZQHWCTRL, 0xa1390003
-DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x001F001F
-DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x001F001F
-DATA 4, MX6_MMDC_P1_MPWLDECTRL0, 0x001F001F
-DATA 4, MX6_MMDC_P1_MPWLDECTRL1, 0x001F001F
-/*
- * DQS gating, read delay, write delay calibration values
- * based on calibration compare of 0x00ffff00
- */
-DATA 4, MX6_MMDC_P0_MPDGCTRL0, 0x420E020E
-DATA 4, MX6_MMDC_P0_MPDGCTRL1, 0x02000200
-DATA 4, MX6_MMDC_P1_MPDGCTRL0, 0x42020202
-DATA 4, MX6_MMDC_P1_MPDGCTRL1, 0x01720172
-DATA 4, MX6_MMDC_P0_MPRDDLCTL, 0x494C4F4C
-DATA 4, MX6_MMDC_P1_MPRDDLCTL, 0x4A4C4C49
-DATA 4, MX6_MMDC_P0_MPWRDLCTL, 0x3F3F3133
-DATA 4, MX6_MMDC_P1_MPWRDLCTL, 0x39373F2E
-/* read data bit delay */
-DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333
-/* Complete calibration by forced measurment */
-DATA 4, MX6_MMDC_P0_MPMUR0, 0x00000800
-DATA 4, MX6_MMDC_P1_MPMUR0, 0x00000800
-/* in DDR3, 64-bit mode, only MMDC0 is initiated */
-DATA 4, MX6_MMDC_P0_MDPDC, 0x0002002d
-DATA 4, MX6_MMDC_P0_MDOTC, 0x00333030
-DATA 4, MX6_MMDC_P0_MDCFG0, 0x40445323
-DATA 4, MX6_MMDC_P0_MDCFG1, 0xb66e8c63
-DATA 4, MX6_MMDC_P0_MDCFG2, 0x01ff00db
-DATA 4, MX6_MMDC_P0_MDMISC, 0x00081740
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00008000
-DATA 4, MX6_MMDC_P0_MDRWD, 0x000026d2
-DATA 4, MX6_MMDC_P0_MDOR, 0x00440e21
-DATA 4, MX6_MMDC_P0_MDASP, 0x00000027
-DATA 4, MX6_MMDC_P0_MDCTL, 0x84190000
-/* MR2 */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x04008032
-DATA 4, MX6_MMDC_P0_MDSCR, 0x0400803a
-/* MR3 */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00008033
-DATA 4, MX6_MMDC_P0_MDSCR, 0x0000803b
-/* MR1 */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00428031
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00428039
-/* MR0 */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x07208030
-DATA 4, MX6_MMDC_P0_MDSCR, 0x07208038
-/* ZQ calibration */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x04008040
-DATA 4, MX6_MMDC_P0_MDSCR, 0x04008048
-/* final ddr setup */
-DATA 4, MX6_MMDC_P0_MDREF, 0x00005800
-DATA 4, MX6_MMDC_P0_MPODTCTRL, 0x00000007
-DATA 4, MX6_MMDC_P1_MPODTCTRL, 0x00000007
-DATA 4, MX6_MMDC_P0_MDPDC, 0x0002556d
-DATA 4, MX6_MMDC_P1_MAPSR, 0x00011006
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00000000
gpio_direction_output(GPIO_LED_PWR_G, 0);
}
-#ifdef CONFIG_USB_EHCI_MX5
-int board_ehci_hcd_init(int port)
-{
- /* request VBUS power enable pin, GPIO7_8 */
- gpio_direction_output(IMX_GPIO_NR(7, 8), 1);
- return 0;
-}
-#endif
-
-
static int power_init(void)
{
/* nothing to do on CX9020 */
static inline void cm_fx6_setup_display(void) {}
#endif /* CONFIG_VIDEO_IPUV3 */
+int ipu_displays_init(void)
+{
+ return board_video_skip();
+}
+
#ifdef CONFIG_DWC_AHSATA
static int cm_fx6_issd_gpios[] = {
/* The order of the GPIOs in the array is important! */
--- /dev/null
+if TARGET_MX7ULP_COM
+
+config SYS_BOARD
+ default "mx7ulp_com"
+
+config SYS_VENDOR
+ default "ea"
+
+config SYS_CONFIG_NAME
+ default "mx7ulp_com"
+
+endif
--- /dev/null
+MX7ULPCOM BOARD
+M: Fabio Estevam <festevam@gmail.com>
+S: Maintained
+F: board/ea/mx7ulp_com/
+F: include/configs/mx7ulp_com.h
+F: configs/mx7ulp_com_defconfig
--- /dev/null
+# (C) Copyright 2016 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := mx7ulp_com.o
--- /dev/null
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi/sd/nand/onenand, qspi/nor
+ */
+
+BOOT_FROM sd
+
+#ifdef CONFIG_USE_IMXIMG_PLUGIN
+/*PLUGIN plugin-binary-file IRAM_FREE_START_ADDR*/
+PLUGIN board/freescale/mx7ulp_evk/plugin.bin 0x2F020000
+#else
+
+#ifdef CONFIG_SECURE_BOOT
+CSF CONFIG_CSF_SIZE
+#endif
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+DATA 4 0x403f00dc 0x00000000
+DATA 4 0x403e0040 0x01000020
+DATA 4 0x403e0500 0x01000000
+DATA 4 0x403e050c 0x80808080
+DATA 4 0x403e0508 0x00160002
+DATA 4 0x403E0510 0x00000001
+DATA 4 0x403E0514 0x00000014
+DATA 4 0x403e0500 0x00000001
+CHECK_BITS_SET 4 0x403e0500 0x01000000
+/*
+ * Default PFD0 divide is 27, which generates:
+ * PFD0 Freq = A7 APLL (528MHz) * 18 / 27 = 352MHz
+ *
+ * i.MX7ULP COM board can not run DDR at 352MHz, so
+ * use a divider of 30 (0x1E), which gives:
+ *
+ * PFD0 Freq = A7 APLL (528MHz) * 18 / 30 = 316.8MHz
+ */
+DATA 4 0x403e050c 0x8080801E
+CHECK_BITS_SET 4 0x403e050c 0x00000040
+DATA 4 0x403E0030 0x00000001
+DATA 4 0x403e0040 0x11000020
+DATA 4 0x403f00dc 0x42000000
+
+DATA 4 0x40B300AC 0x40000000
+
+DATA 4 0x40AD0128 0x00040000
+DATA 4 0x40AD00F8 0x00000000
+DATA 4 0x40AD00D8 0x00000180
+DATA 4 0x40AD0104 0x00000180
+DATA 4 0x40AD0108 0x00000180
+DATA 4 0x40AD0124 0x00010000
+DATA 4 0x40AD0080 0x0000018C
+DATA 4 0x40AD0084 0x0000018C
+DATA 4 0x40AD0088 0x0000018C
+DATA 4 0x40AD008C 0x0000018C
+
+DATA 4 0x40AD0120 0x00010000
+DATA 4 0x40AD010C 0x00000180
+DATA 4 0x40AD0110 0x00000180
+DATA 4 0x40AD0114 0x00000180
+DATA 4 0x40AD0118 0x00000180
+DATA 4 0x40AD0090 0x00000180
+DATA 4 0x40AD0094 0x00000180
+DATA 4 0x40AD0098 0x00000180
+DATA 4 0x40AD009C 0x00000180
+
+DATA 4 0x40AD00E0 0x00040000
+DATA 4 0x40AD00E4 0x00040000
+
+DATA 4 0x40AB001C 0x00008000
+DATA 4 0x40AB085C 0x0D3900A0
+DATA 4 0x40AB0800 0xA1390003
+DATA 4 0x40AB0890 0x00400000
+DATA 4 0x40AB081C 0x33333333
+DATA 4 0x40AB0820 0x33333333
+DATA 4 0x40AB0824 0x33333333
+DATA 4 0x40AB0828 0x33333333
+DATA 4 0x40AB08C0 0x24922492
+DATA 4 0x40AB0848 0x3A3E3838
+DATA 4 0x40AB0850 0x28282C2A
+DATA 4 0x40AB083C 0x20000000
+DATA 4 0x40AB0840 0x00000000
+DATA 4 0x40AB08B8 0x00000800
+DATA 4 0x40AB000C 0x292C40F5
+DATA 4 0x40AB0004 0x00020064
+DATA 4 0x40AB0010 0xB6AD0A83
+DATA 4 0x40AB0014 0x00C70093
+DATA 4 0x40AB0018 0x00211708
+DATA 4 0x40AB002C 0x0F9F26D2
+DATA 4 0x40AB0030 0x009F0E10
+DATA 4 0x40AB0038 0x00130556
+DATA 4 0x40AB0008 0x12272000
+DATA 4 0x40AB0040 0x0000003F
+DATA 4 0x40AB0000 0xC3110000
+DATA 4 0x40AB001C 0x00008010
+DATA 4 0x40AB001C 0x00008018
+DATA 4 0x40AB001C 0x003F8030
+DATA 4 0x40AB001C 0xFF0A8030
+DATA 4 0x40AB001C 0x82018030
+DATA 4 0x40AB001C 0x06028030
+DATA 4 0x40AB001C 0x01038030
+DATA 4 0x40AB001C 0x003F8038
+DATA 4 0x40AB001C 0xFF0A8038
+DATA 4 0x40AB001C 0x82018038
+DATA 4 0x40AB001C 0x06028038
+DATA 4 0x40AB001C 0x01038038
+DATA 4 0x40AB083C 0xA0000000
+DATA 4 0x40AB083C 0xA0000000
+DATA 4 0x40AB0020 0x00001800
+DATA 4 0x40AB0800 0xA1310003
+DATA 4 0x40AB001C 0x00000000
+#endif
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mx7ulp-pins.h>
+#include <asm/arch/iomux.h>
+#include <asm/gpio.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PUS_UP)
+
+int dram_init(void)
+{
+ gd->ram_size = imx_ddr_size();
+
+ return 0;
+}
+
+static iomux_cfg_t const lpuart4_pads[] = {
+ MX7ULP_PAD_PTC3__LPUART4_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX7ULP_PAD_PTC2__LPUART4_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ mx7ulp_iomux_setup_multiple_pads(lpuart4_pads,
+ ARRAY_SIZE(lpuart4_pads));
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ return 0;
+}
#include <env.h>
#include <init.h>
#include <mmc.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
#include <asm/arch/sys_proto.h>
#include <watchdog.h>
}
#endif
-static void setenv_fdt_file(void)
+enum engicam_boards {
+ IMX6Q_ICORE,
+ IMX6DL_ICORE,
+ IMX6Q_ICORE_MIPI,
+ IMX6DL_ICORE_MIPI,
+ IMX6Q_ICORE_RQS,
+ IMX6DL_ICORE_RQS,
+ IMX6UL_GEAM,
+ IMX6UL_ISIOT_EMMC,
+ IMX6UL_ISIOT_NAND,
+ ENGICAM_BOARDS,
+};
+
+static const char * const board_fdt_file[ENGICAM_BOARDS] = {
+ [IMX6Q_ICORE] = "imx6q-icore.dtb",
+ [IMX6DL_ICORE] = "imx6dl-icore.dtb",
+ [IMX6Q_ICORE_MIPI] = "imx6q-icore-mipi.dtb",
+ [IMX6DL_ICORE_MIPI] = "imx6dl-icore-mipi.dtb",
+ [IMX6Q_ICORE_RQS] = "imx6q-icore-rqs.dtb",
+ [IMX6DL_ICORE_RQS] = "imx6dl-icore-rqs.dtb",
+ [IMX6UL_GEAM] = "imx6ul-geam.dtb",
+ [IMX6UL_ISIOT_EMMC] = "imx6ul-isiot-emmc.dtb",
+ [IMX6UL_ISIOT_NAND] = "imx6ul-isiot-nand.dtb",
+};
+
+static int setenv_fdt_file(int board_detected)
+{
+ if (board_detected < 0 || board_detected >= ENGICAM_BOARDS)
+ return -EINVAL;
+
+ if (!board_fdt_file[board_detected])
+ return -ENODEV;
+
+ env_set("fdt_file", board_fdt_file[board_detected]);
+ return 0;
+}
+
+static enum engicam_boards engicam_board_detect(void)
{
const char *cmp_dtb = CONFIG_DEFAULT_DEVICE_TREE;
if (!strcmp(cmp_dtb, "imx6q-icore")) {
if (is_mx6dq())
- env_set("fdt_file", "imx6q-icore.dtb");
+ return IMX6Q_ICORE;
else if (is_mx6dl() || is_mx6solo())
- env_set("fdt_file", "imx6dl-icore.dtb");
+ return IMX6DL_ICORE;
} else if (!strcmp(cmp_dtb, "imx6q-icore-mipi")) {
if (is_mx6dq())
- env_set("fdt_file", "imx6q-icore-mipi.dtb");
+ return IMX6Q_ICORE_MIPI;
else if (is_mx6dl() || is_mx6solo())
- env_set("fdt_file", "imx6dl-icore-mipi.dtb");
+ return IMX6DL_ICORE_MIPI;
} else if (!strcmp(cmp_dtb, "imx6q-icore-rqs")) {
if (is_mx6dq())
- env_set("fdt_file", "imx6q-icore-rqs.dtb");
+ return IMX6Q_ICORE_RQS;
else if (is_mx6dl() || is_mx6solo())
- env_set("fdt_file", "imx6dl-icore-rqs.dtb");
+ return IMX6DL_ICORE_RQS;
} else if (!strcmp(cmp_dtb, "imx6ul-geam"))
- env_set("fdt_file", "imx6ul-geam.dtb");
+ return IMX6UL_GEAM;
else if (!strcmp(cmp_dtb, "imx6ul-isiot-emmc"))
- env_set("fdt_file", "imx6ul-isiot-emmc.dtb");
+ return IMX6UL_ISIOT_EMMC;
else if (!strcmp(cmp_dtb, "imx6ul-isiot-nand"))
- env_set("fdt_file", "imx6ul-isiot-nand.dtb");
+ return IMX6UL_ISIOT_NAND;
+
+ return -EINVAL;
+}
+
+static int fixup_enet_clock(enum engicam_boards board_detected)
+{
+ struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ int clk_internal = 0;
+
+ switch (board_detected) {
+ case IMX6Q_ICORE_MIPI:
+ case IMX6DL_ICORE_MIPI:
+ clk_internal = 1;
+ break;
+ default:
+ break;
+ }
+
+ /* set gpr1[21] to select anatop clock */
+ debug("fixup_enet_clock %d\n", clk_internal);
+ clrsetbits_le32(&iomuxc_regs->gpr[1], 0x1 << 21, clk_internal << 21);
+
+ if (!clk_internal) {
+ /* clock is external */
+ return 0;
+ }
+
+ return enable_fec_anatop_clock(0, ENET_50MHZ);
}
int board_late_init(void)
{
+ enum engicam_boards board_detected = IMX6Q_ICORE;
+
switch ((imx6_src_get_boot_mode() & IMX6_BMODE_MASK) >>
IMX6_BMODE_SHIFT) {
case IMX6_BMODE_SD:
else
env_set("console", "ttymxc3");
- setenv_fdt_file();
+ board_detected = engicam_board_detect();
+ if (board_detected < 0)
+ hang();
+
+ fixup_enet_clock(board_detected);
+ setenv_fdt_file(board_detected);
#ifdef CONFIG_HW_WATCHDOG
hw_watchdog_init();
Get and Build the ARM Trusted firmware
======================================
-Note: srctree is U-Boot source directory
+Note: builddir is U-Boot build directory (source directory for in-tree builds)
Get ATF from: https://source.codeaurora.org/external/imx/imx-atf
branch: imx_4.19.35_1.0.0
$ make PLAT=imx8mm bl31
-$ cp build/imx8mm/release/bl31.bin $(srctree)
+$ cp build/imx8mm/release/bl31.bin $(builddir)
Get the ddr and hdmi firmware
=============================
$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin
$ chmod +x firmware-imx-8.0.bin
$ ./firmware-imx-8.0
-$ cp firmware-imx-7.9/firmware/ddr/synopsys/lpddr4*.bin $(srctree)
+$ cp firmware-imx-7.9/firmware/ddr/synopsys/lpddr4*.bin $(builddir)
Build U-Boot
============
Get ATF from: https://source.codeaurora.org/external/imx/imx-atf
branch: imx_4.19.35_1.0.0
$ make PLAT=imx8mq bl31
-$ cp build/imx8mq/release/bl31.bin $(srctree)
+$ cp build/imx8mq/release/bl31.bin $(builddir)
Get the ddr and hdmi firmware
=============================
$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-7.9.bin
$ chmod +x firmware-imx-7.9.bin
$ ./firmware-imx-7.9.bin
-$ cp firmware-imx-7.9/firmware/hdmi/cadence/signed_hdmi_imx8m.bin $(srctree)
-$ cp firmware-imx-7.9/firmware/ddr/synopsys/lpddr4*.bin $(srctree)
+$ cp firmware-imx-7.9/firmware/hdmi/cadence/signed_hdmi_imx8m.bin $(builddir)
+$ cp firmware-imx-7.9/firmware/ddr/synopsys/lpddr4*.bin $(builddir)
Build U-Boot
============
u32 switch_num = 6;
u32 offset = PFUZE100_SW1CMODE;
- ret = pmic_get("pfuze100", &dev);
+ ret = pmic_get("pfuze100@08", &dev);
if (ret == -ENODEV)
return 0;
u32 switch_num = 6;
u32 offset = PFUZE100_SW1CMODE;
- ret = pmic_get("pfuze100", &dev);
+ ret = pmic_get("pfuze100@08", &dev);
if (ret == -ENODEV)
return 0;
#include <fsl_esdhc_imx.h>
#include <mmc.h>
#include <miiphy.h>
-#include <netdev.h>
#include <power/pmic.h>
#include <power/pfuze3000_pmic.h>
#include "../common/pfuze.h"
#define UART_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | \
PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS)
-#define ENET_PAD_CTRL (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
-#define ENET_PAD_CTRL_MII (PAD_CTL_DSE_3P3V_32OHM)
-
-#define ENET_RX_PAD_CTRL (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
-
#define LCD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_PU100KOHM | \
PAD_CTL_DSE_3P3V_49OHM)
}
#endif
-#ifdef CONFIG_FEC_MXC
-static iomux_v3_cfg_t const fec1_pads[] = {
- MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX7D_PAD_GPIO1_IO10__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
- MX7D_PAD_GPIO1_IO11__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
-};
-
-static void setup_iomux_fec(void)
-{
- imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
-}
-#endif
-
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
}
#ifdef CONFIG_FEC_MXC
-int board_eth_init(bd_t *bis)
-{
- int ret;
- unsigned int gpio;
-
- ret = gpio_lookup_name("gpio_spi@0_5", NULL, NULL, &gpio);
- if (ret) {
- printf("GPIO: 'gpio_spi@0_5' not found\n");
- return -ENODEV;
- }
-
- ret = gpio_request(gpio, "fec_rst");
- if (ret && ret != -EBUSY) {
- printf("gpio: requesting pin %u failed\n", gpio);
- return ret;
- }
-
- gpio_direction_output(gpio, 0);
- udelay(500);
- gpio_direction_output(gpio, 1);
-
- setup_iomux_fec();
-
- ret = fecmxc_initialize_multi(bis, 0,
- CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
- if (ret)
- printf("FEC1 MXC: %s:failed\n", __func__);
-
- return ret;
-}
-
static int setup_fec(void)
{
struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
return set_clk_enet(ENET_125MHZ);
}
-
int board_phy_config(struct phy_device *phydev)
{
/* enable rgmii rxc skew and phy mode select to RGMII copper */
struct udevice *dev;
int ret, dev_id, rev_id;
- ret = pmic_get("pfuze3000", &dev);
+ ret = pmic_get("pfuze3000@08", &dev);
if (ret == -ENODEV)
return 0;
if (ret != 0)
#include <pwm.h>
#include <version.h>
#include <stdlib.h>
+#include <dm/root.h>
#include "../common/ge_common.h"
#include "../common/vpd_reader.h"
#include "../../../drivers/net/e1000.h"
+#include <pci.h>
+
DECLARE_GLOBAL_DATA_PTR;
-static int confidx = 3; /* Default to b850v3. */
+static int confidx; /* Default to generic. */
static struct vpd_cache vpd;
#define NC_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
};
-static iomux_v3_cfg_t const enet_pads[] = {
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
- MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- /* AR8033 PHY Reset */
- MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static void setup_iomux_enet(void)
-{
- imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
-
- /* Reset AR8033 PHY */
- gpio_request(IMX_GPIO_NR(1, 28), "fec_rst");
- gpio_direction_output(IMX_GPIO_NR(1, 28), 0);
- mdelay(10);
- gpio_set_value(IMX_GPIO_NR(1, 28), 1);
- mdelay(1);
-}
-
static struct i2c_pads_info i2c_pad_info1 = {
.scl = {
.i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD,
}
};
-static iomux_v3_cfg_t const pcie_pads[] = {
- MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static void setup_pcie(void)
-{
- imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
-}
-
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
imx_enable_hdmi_phy();
}
-int board_cfb_skip(void)
-{
- gpio_direction_output(LVDS_POWER_GP, 1);
-
- return 0;
-}
-
static int is_b850v3(void)
{
return confidx == 3;
static void process_vpd(struct vpd_cache *vpd)
{
- int fec_index = -1;
+ int fec_index = 0;
int i210_index = -1;
if (!vpd->is_read) {
return;
}
+ if (vpd->has & VPD_HAS_MAC1)
+ eth_env_set_enetaddr_by_index("eth", fec_index, vpd->mac1);
+
+ env_set("ethact", "eth0");
+
switch (vpd->product_id) {
case VPD_PRODUCT_B450:
env_set("confidx", "1");
- i210_index = 0;
- fec_index = 1;
+ i210_index = 1;
break;
case VPD_PRODUCT_B650:
env_set("confidx", "2");
- i210_index = 0;
- fec_index = 1;
+ i210_index = 1;
break;
case VPD_PRODUCT_B850:
env_set("confidx", "3");
- i210_index = 1;
- fec_index = 2;
+ i210_index = 2;
break;
}
- if (fec_index >= 0 && (vpd->has & VPD_HAS_MAC1))
- eth_env_set_enetaddr_by_index("eth", fec_index, vpd->mac1);
-
if (i210_index >= 0 && (vpd->has & VPD_HAS_MAC2))
eth_env_set_enetaddr_by_index("eth", i210_index, vpd->mac2);
}
-int board_eth_init(bd_t *bis)
-{
- setup_iomux_enet();
- setup_pcie();
-
- e1000_initialize(bis);
-
- return cpu_eth_init(bis);
-}
-
static iomux_v3_cfg_t const misc_pads[] = {
MX6_PAD_KEY_ROW2__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NC_PAD_CTRL),
setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
if (!read_vpd(&vpd, vpd_callback)) {
+ int ret, rescan;
+
vpd.is_read = true;
set_confidx(&vpd);
+
+ ret = fdtdec_resetup(&rescan);
+ if (!ret && rescan) {
+ dm_uninit();
+ dm_init_and_scan(false);
+ }
}
gpio_request(SUS_S3_OUT, "sus_s3_out");
check_time();
+ pci_init();
+
return 0;
}
#ifdef CONFIG_OF_BOARD_SETUP
int ft_board_setup(void *blob, bd_t *bd)
{
+ char *rtc_status = env_get("rtc_status");
+
fdt_setprop(blob, 0, "ge,boot-ver", version_string,
- strlen(version_string) + 1);
+ strlen(version_string) + 1);
+
+ fdt_setprop(blob, 0, "ge,rtc-status", rtc_status,
+ strlen(rtc_status) + 1);
return 0;
}
#endif
static int do_backlight_enable(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
+#if CONFIG_IS_ENABLED(DM_VIDEO)
+ int ret;
+ struct udevice *dev;
+
#ifdef CONFIG_VIDEO_IPUV3
- /* We need at least 200ms between power on and backlight on
- * as per specifications from CHI MEI */
- mdelay(250);
+ if (!is_b850v3()) {
+ gpio_direction_output(LVDS_POWER_GP, 1);
- /* enable backlight PWM 1 */
- pwm_init(0, 0, 0);
+ /* We need at least 200ms between power on and backlight on
+ * as per specifications from CHI MEI
+ */
+ mdelay(250);
- /* duty cycle 5000000ns, period: 5000000ns */
- pwm_config(0, 5000000, 5000000);
+ /* enable backlight PWM 1 */
+ pwm_init(0, 0, 0);
- /* Backlight Power */
- gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
+ /* duty cycle 5000000ns, period: 5000000ns */
+ pwm_config(0, 5000000, 5000000);
+
+ /* Backlight Power */
+ gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
+
+ pwm_enable(0);
+ }
+#endif
- pwm_enable(0);
+ /* Probe, to find a video device to be used to show a message on
+ * the vidconsole.
+ */
+ ret = uclass_get_device(UCLASS_VIDEO, 0, &dev);
+ if (ret)
+ return ret;
#endif
return 0;
"enable Bx50 backlight",
""
);
+
+int board_fit_config_name_match(const char *name)
+{
+ if (!vpd.is_read)
+ return strcmp(name, "imx6q-bx50v3");
+
+ switch (vpd.product_id) {
+ case VPD_PRODUCT_B450:
+ return strcmp(name, "imx6q-b450v3");
+ case VPD_PRODUCT_B650:
+ return strcmp(name, "imx6q-b650v3");
+ case VPD_PRODUCT_B850:
+ return strcmp(name, "imx6q-b850v3");
+ default:
+ return -1;
+ }
+}
+
+int embedded_dtb_select(void)
+{
+ vpd.is_read = false;
+ return fdtdec_setup();
+}
unsigned int current_i2c_bus = i2c_get_bus_num();
ret = i2c_set_bus_num(CONFIG_SYS_RTC_BUS_NUM);
- if (ret < 0)
+ if (ret < 0) {
+ env_set("rtc_status", "FAIL");
return;
+ }
rtc_init();
break;
}
- if (ret < 0)
- env_set("rtc_status", "RTC_ERROR");
-
- if (tm.tm_year > 2037) {
+ if (!ret && tm.tm_year > 2037) {
tm.tm_sec = 0;
tm.tm_min = 0;
tm.tm_hour = 0;
break;
}
- if (ret < 0)
- env_set("rtc_status", "RTC_ERROR");
+ if (ret >= 0)
+ ret = 2038;
}
+ if (ret < 0)
+ env_set("rtc_status", "FAIL");
+ else if (ret == 2038)
+ env_set("rtc_status", "2038");
+ else
+ env_set("rtc_status", "OK");
+
i2c_set_bus_num(current_i2c_bus);
}
return res;
print_cpuinfo();
- hw_watchdog_init();
check_time();
#ifdef CONFIG_OF_BOARD_SETUP
int ft_board_setup(void *blob, bd_t *bd)
{
+ char *rtc_status = env_get("rtc_status");
+
fdt_setprop(blob, 0, "ge,boot-ver", version_string,
- strlen(version_string) + 1);
+ strlen(version_string) + 1);
+
+ fdt_setprop(blob, 0, "ge,rtc-status", rtc_status,
+ strlen(rtc_status) + 1);
return 0;
}
#endif
--- /dev/null
+if TARGET_XEA
+
+config SYS_BOARD
+ default "xea"
+
+config SYS_VENDOR
+ default "liebherr"
+
+config SYS_SOC
+ default "mxs"
+
+config SYS_CONFIG_NAME
+ default "xea"
+
+config ENV_SIZE
+ default 0x2000
+
+config ENV_SECT_SIZE
+ default 0x10000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET
+ default 0x80000 if ENV_IS_IN_SPI_FLASH
+
+endif
--- /dev/null
+XEA BOARD
+M: Lukasz Majewski <lukma@denx.de>
+S: Maintained
+F: board/liebherr/xea/
+F: include/configs/xea.h
+F: configs/imx28_xea_defconfig
--- /dev/null
+#
+# (C) Copyright 2019
+# Lukasz Majewski, DENX Software Engineering, lukma@denx.de.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := xea.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl_xea.o
+endif
--- /dev/null
+Building SPL/U-Boot for xea board
+=================================
+
+Setup environment, configure and build, e.g. by:
+
+ $ make imx28_xea_defconfig
+ $ make -j4 u-boot.sb u-boot.img
+
+Now you should see u-boot.sb and u-boot.img files in the build directory.
+
+
+Booting
+=======
+
+The boot ROM loads SPL from SPI NOR flash into SRAM. SPL configures
+DRAM and loads either a Linux kernel (falcon mode) or, if the rescue
+pin is asserted, the main U-Boot. Both kernel and U-Boot reside in
+eMMC boot partition 0. For redundancy, a copy of U-Boot is also
+stored in SPI flash. If a valid kernel image is not found, U-Boot is
+loaded from eMMC or, if this fails, SPI flash.
+
+Boot area layout
+----------------
+
+SPI NOR
+Offset Function File
+------------------------------------------
+0x00000000 SPL u-boot.sb
+0x00010000 U-Boot u-boot.img
+0x00080000 Environment
+
+eMMC
+Offset Function File
+------------------------------------------
+0x00000000 U-Boot u-boot.img
+0x00080000 Devicetree imx28-bttc.dtb
+0x00100000 Kernel uImage
+
+
+Falcon mode
+===========
+
+In falcon mode, the default, SPL loads the kernel and devicetree
+directly. For this to work, the stored devicetree must include
+correct "memory" and "chosen" nodes as these are not updated by SPL
+before booting the kernel.
+
+
+Updating from U-Boot
+====================
+
+The default U-Boot environment includes command sequences to update
+SPL, U-Boot, and kernel over TFTP. These are as follows:
+
+- update_spl: writes u-boot.sb to SPI NOR
+- update_uboot: writes u-boot.img to eMMC and SPI NOR
+- update_kernel: writes kernel and devicetree to eMMC
+
+They can be invoked at the U-Boot prompt using the "run" command,
+e.g. "run update_spl" to update the SPL.
+
+These update commands download the above-named files from the
+${hostname} directory on the server provided by DHCP.
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * DENX M28 Boot setup
+ *
+ * Copyright (C) 2019 DENX Software Engineering
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ *
+ * Copyright (C) 2018 DENX Software Engineering
+ * Måns Rullgård, DENX Software Engineering, mans@mansr.com
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+
+#define MUX_CONFIG_LCD (MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_NOPULL)
+#define MUX_CONFIG_BOOT (MXS_PAD_3V3 | MXS_PAD_PULLUP)
+#define MUX_CONFIG_TSC (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define MUX_CONFIG_SSP0 (MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_PULLUP)
+#define MUX_CONFIG_SSP2 (MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_PULLUP)
+#define MUX_CONFIG_ENET (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_NOPULL)
+#define MUX_CONFIG_EMI (MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
+
+const iomux_cfg_t iomux_setup[] = {
+ /* AUART0 IRDA */
+ MX28_PAD_AUART0_RX__AUART0_RX,
+ MX28_PAD_AUART0_TX__AUART0_TX,
+
+ /* AUART 4 RS422 */
+ MX28_PAD_AUART0_CTS__AUART4_RX,
+ MX28_PAD_AUART0_RTS__AUART4_TX,
+
+ /* USB0 */
+ MX28_PAD_AUART1_CTS__USB0_OVERCURRENT,
+ MX28_PAD_AUART1_RTS__USB0_ID,
+ MX28_PAD_LCD_VSYNC__GPIO_1_28, /* PRW_On */
+
+ /* USB1 */
+ MX28_PAD_PWM2__USB1_OVERCURRENT,
+
+ /* eMMC */
+ MX28_PAD_SSP0_CMD__SSP0_CMD | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA0__SSP0_D0 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA1__SSP0_D1 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA2__SSP0_D2 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA3__SSP0_D3 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA4__SSP0_D4 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA5__SSP0_D5 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA6__SSP0_D6 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA7__SSP0_D7 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DETECT__GPIO_2_9, /* Reset for eMMC */
+ MX28_PAD_SSP0_SCK__SSP0_SCK | MUX_CONFIG_SSP0,
+
+ /* DIG Keys */
+ MX28_PAD_GPMI_D00__GPIO_0_0,
+ MX28_PAD_GPMI_D01__GPIO_0_1,
+ MX28_PAD_GPMI_D02__GPIO_0_2,
+ MX28_PAD_GPMI_D03__GPIO_0_3,
+ MX28_PAD_GPMI_D04__GPIO_0_4,
+ MX28_PAD_GPMI_D05__GPIO_0_5,
+ MX28_PAD_GPMI_D06__GPIO_0_6,
+ MX28_PAD_GPMI_D07__GPIO_0_7,
+
+ /* ADR_0-2 */
+ MX28_PAD_GPMI_CE1N__GPIO_0_17,
+ MX28_PAD_GPMI_CE2N__GPIO_0_18,
+ MX28_PAD_GPMI_CE3N__GPIO_0_19,
+
+ /* Read Keys */
+ MX28_PAD_GPMI_RDY0__GPIO_0_20,
+
+ /* LATCH_EN */
+ MX28_PAD_GPMI_RDY1__GPIO_0_21,
+
+ /* Power off */
+ MX28_PAD_GPMI_RDN__GPIO_0_24,
+
+ /* I2C1 Touch */
+ MX28_PAD_AUART2_CTS__GPIO_3_10,
+ MX28_PAD_AUART2_RTS__GPIO_3_11,
+ MX28_PAD_GPMI_RDY2__GPIO_0_22, /* Touch Reset */
+
+ /* TIVA */
+ MX28_PAD_AUART1_RX__SSP2_CARD_DETECT,
+ MX28_PAD_SSP2_MISO__SSP2_D0,
+ MX28_PAD_SSP2_MOSI__SSP2_CMD,
+ MX28_PAD_SSP2_SCK__SSP2_SCK,
+ MX28_PAD_SSP2_SS0__SSP2_D3,
+ MX28_PAD_SSP2_SS1__GPIO_2_20,
+ MX28_PAD_SSP2_SS2__GPIO_2_21,
+
+ /* SPI3 NOR-Flash */
+ MX28_PAD_AUART1_TX__SSP3_CARD_DETECT,
+ MX28_PAD_AUART2_RX__SSP3_D1,
+ MX28_PAD_AUART2_TX__SSP3_D2,
+ MX28_PAD_SSP3_MISO__SSP3_D0,
+ MX28_PAD_SSP3_MOSI__SSP3_CMD,
+ MX28_PAD_SSP3_SCK__SSP3_SCK,
+ MX28_PAD_SSP3_SS0__SSP3_D3,
+
+ /* NOR-Flash CMD */
+ MX28_PAD_LCD_RS__GPIO_1_26, /* Hold */
+ MX28_PAD_LCD_WR_RWN__GPIO_1_25, /* write protect */
+
+ /* I2C0 Codec */
+ MX28_PAD_I2C0_SCL__I2C0_SCL,
+ MX28_PAD_I2C0_SDA__I2C0_SDA,
+
+ /* I2S Codec */
+ MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK,
+ MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK,
+ MX28_PAD_SAIF0_MCLK__SAIF0_MCLK,
+ MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0,
+ MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0,
+
+ /* PWR-Hold */
+ MX28_PAD_SPDIF__GPIO_3_27,
+
+ /* EMI */
+ MX28_PAD_EMI_D00__EMI_DATA0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D01__EMI_DATA1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D02__EMI_DATA2 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D03__EMI_DATA3 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D04__EMI_DATA4 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D05__EMI_DATA5 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D06__EMI_DATA6 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D07__EMI_DATA7 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D08__EMI_DATA8 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D09__EMI_DATA9 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D10__EMI_DATA10 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D11__EMI_DATA11 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D12__EMI_DATA12 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D13__EMI_DATA13 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D14__EMI_DATA14 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D15__EMI_DATA15 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_ODT0__EMI_ODT0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQM0__EMI_DQM0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_ODT1__EMI_ODT1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQM1__EMI_DQM1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CLK__EMI_CLK | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQS0__EMI_DQS0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQS1__EMI_DQS1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN | MUX_CONFIG_EMI,
+
+ MX28_PAD_EMI_A00__EMI_ADDR0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A01__EMI_ADDR1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A02__EMI_ADDR2 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A03__EMI_ADDR3 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A04__EMI_ADDR4 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A05__EMI_ADDR5 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A06__EMI_ADDR6 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A07__EMI_ADDR7 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A08__EMI_ADDR8 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A09__EMI_ADDR9 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A10__EMI_ADDR10 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A11__EMI_ADDR11 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A12__EMI_ADDR12 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A13__EMI_ADDR13 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A14__EMI_ADDR14 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_BA0__EMI_BA0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_BA1__EMI_BA1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_BA2__EMI_BA2 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CASN__EMI_CASN | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_RASN__EMI_RASN | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_WEN__EMI_WEN | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
+
+ /* Uart3 Bluetooth-Interface */
+ MX28_PAD_AUART3_CTS__AUART3_CTS,
+ MX28_PAD_AUART3_RTS__AUART3_RTS,
+ MX28_PAD_AUART3_RX__AUART3_RX,
+ MX28_PAD_AUART3_TX__AUART3_TX,
+
+ /* framebuffer */
+ MX28_PAD_LCD_CS__LCD_CS | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D00__LCD_D0 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D01__LCD_D1 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D02__LCD_D2 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D03__LCD_D3 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D04__LCD_D4 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D05__LCD_D5 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D06__LCD_D6 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D07__LCD_D7 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D08__LCD_D8 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D09__LCD_D9 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D10__LCD_D10 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D11__LCD_D11 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D12__LCD_D12 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D13__LCD_D13 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D14__LCD_D14 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D15__LCD_D15 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D16__LCD_D16 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D17__LCD_D17 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D18__LCD_D18 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D19__LCD_D19 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D20__LCD_D20 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D21__LCD_D21 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D22__LCD_D22 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D23__LCD_D23 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_DOTCLK__LCD_DOTCLK | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_ENABLE__LCD_ENABLE | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_HSYNC__LCD_HSYNC | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_RD_E__LCD_VSYNC | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_RESET__LCD_RESET | MUX_CONFIG_LCD,
+
+ /* DUART RS232 */
+ MX28_PAD_PWM0__DUART_RX,
+ MX28_PAD_PWM1__DUART_TX,
+
+ /* FEC Ethernet */
+ MX28_PAD_ENET_CLK__CLKCTRL_ENET | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_COL__ENET1_TX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_CRS__ENET1_RX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_MDC__ENET0_MDC | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_MDIO__ENET0_MDIO | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13, /* Phy Interrupt */
+ MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RXD3__ENET1_RXD1 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TX_CLK__GPIO_4_5, /* n.c. */
+ MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TXD3__ENET1_TXD1 | MUX_CONFIG_ENET,
+ MX28_PAD_SSP1_CMD__GPIO_2_13, /* PHY reset */
+
+ /* TIVA boot control */
+ MX28_PAD_GPMI_RDY3__GPIO_0_23 | MUX_CONFIG_BOOT, /* TIVA0 */
+ MX28_PAD_GPMI_WRN__GPIO_0_25 | MUX_CONFIG_BOOT, /* TIVA1 */
+};
+
+u32 mxs_dram_vals[] = {
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000100, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00010101, 0x01010101,
+ 0x000f0f01, 0x0f02010a, 0x00000000, 0x00010101,
+ 0x00000100, 0x00000100, 0x00000000, 0x00000002,
+ 0x01010000, 0x07080403, 0x07005303, 0x0b0000c8,
+ 0x0200a0c1, 0x0002040c, 0x0038430a, 0x04290322,
+ 0x02040203, 0x00c8002b, 0x00000000, 0x00000000,
+ 0x00012100, 0xffff0303, 0x00012100, 0xffff0303,
+ 0x00012100, 0xffff0303, 0x00012100, 0xffff0303,
+ 0x00000003, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000612, 0x01000102,
+ 0x06120612, 0x00000200, 0x00020007, 0xf4004a27,
+ 0xf4004a27, 0xf4004a27, 0xf4004a27, 0x07400300,
+ 0x07400300, 0x07400300, 0x07400300, 0x00000005,
+ 0x00000000, 0x00000000, 0x01000000, 0x00000000,
+ 0x00000001, 0x000f1133, 0x00000000, 0x00001f04,
+ 0x00001f04, 0x00001f04, 0x00001f04, 0x00001f04,
+ 0x00001f04, 0x00001f04, 0x00001f04, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00010000, 0x00030404,
+ 0x00000002, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x01010000,
+ 0x01000000, 0x03030000, 0x00010303, 0x01020202,
+ 0x00000000, 0x02040101, 0x21002103, 0x00061200,
+ 0x06120612, 0x00000642, 0x00000000, 0x00000004,
+ 0x00000000, 0x00000080, 0x00000000, 0x00000000,
+ 0x00000000, 0xffffffff
+};
+
+void lowlevel_init(void)
+{
+ struct mxs_pinctrl_regs *pinctrl_regs =
+ (struct mxs_pinctrl_regs *)MXS_PINCTRL_BASE;
+
+ /* Set EMI drive strength */
+ writel(0x00003fff, &pinctrl_regs->hw_pinctrl_emi_ds_ctrl_clr);
+ writel(0x00002aaa, &pinctrl_regs->hw_pinctrl_emi_ds_ctrl_set);
+
+ mxs_common_spl_init(0, NULL, iomux_setup, ARRAY_SIZE(iomux_setup));
+}
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * XEA iMX28 board
+ *
+ * Copyright (C) 2019 DENX Software Engineering
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ *
+ * Copyright (C) 2018 DENX Software Engineering
+ * Måns Rullgård, DENX Software Engineering, mans@mansr.com
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <linux/mii.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <errno.h>
+#include <usb.h>
+#include <serial.h>
+
+#ifdef CONFIG_SPL_BUILD
+#include <spl.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Functions
+ */
+
+static void init_clocks(void)
+{
+ /* IO0 clock at 480MHz */
+ mxs_set_ioclk(MXC_IOCLK0, 480000);
+ /* IO1 clock at 480MHz */
+ mxs_set_ioclk(MXC_IOCLK1, 480000);
+
+ /* SSP0 clock at 96MHz */
+ mxs_set_sspclk(MXC_SSPCLK0, 96000, 0);
+ /* SSP2 clock at 160MHz */
+ mxs_set_sspclk(MXC_SSPCLK2, 160000, 0);
+ /* SSP3 clock at 96MHz */
+ mxs_set_sspclk(MXC_SSPCLK3, 96000, 0);
+}
+
+#ifdef CONFIG_SPL_BUILD
+void board_init_f(ulong arg)
+{
+ init_clocks();
+ preloader_console_init();
+}
+
+static int boot_tiva0, boot_tiva1;
+
+/* Check if TIVAs request booting via U-Boot proper */
+void spl_board_init(void)
+{
+ struct gpio_desc btiva0, btiva1;
+ int ret;
+
+ ret = dm_gpio_lookup_name("GPIO0_23", &btiva0);
+ if (ret)
+ printf("Cannot get GPIO0_23\n");
+
+ ret = dm_gpio_lookup_name("GPIO0_25", &btiva1);
+ if (ret)
+ printf("Cannot get GPIO0_25\n");
+
+ ret = dm_gpio_request(&btiva0, "boot-tiva0");
+ if (ret)
+ printf("Cannot request GPIO0_23\n");
+
+ ret = dm_gpio_request(&btiva1, "boot-tiva1");
+ if (ret)
+ printf("Cannot request GPIO0_25\n");
+
+ dm_gpio_set_dir_flags(&btiva0, GPIOD_IS_IN);
+ dm_gpio_set_dir_flags(&btiva1, GPIOD_IS_IN);
+
+ udelay(1000);
+
+ boot_tiva0 = dm_gpio_get_value(&btiva0);
+ boot_tiva1 = dm_gpio_get_value(&btiva1);
+}
+
+void board_boot_order(u32 *spl_boot_list)
+{
+ spl_boot_list[0] = BOOT_DEVICE_MMC1;
+ spl_boot_list[1] = BOOT_DEVICE_SPI;
+}
+
+int spl_start_uboot(void)
+{
+ /* break into full u-boot on 'c' */
+ if (serial_tstc() && serial_getc() == 'c')
+ return 1;
+
+ debug("%s: btiva0: %d btiva1: %d\n", __func__, boot_tiva0, boot_tiva1);
+ return !boot_tiva0 || !boot_tiva1;
+}
+#else
+
+int board_early_init_f(void)
+{
+ init_clocks();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ struct gpio_desc phy_rst;
+ int ret;
+
+ /* Address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+ cpu_eth_init(NULL);
+
+ /* PHY INT#/PWDN# */
+ ret = dm_gpio_lookup_name("GPIO4_13", &phy_rst);
+ if (ret) {
+ printf("Cannot get GPIO4_13\n");
+ return ret;
+ }
+
+ ret = dm_gpio_request(&phy_rst, "phy-rst");
+ if (ret) {
+ printf("Cannot request GPIO4_13\n");
+ return ret;
+ }
+
+ dm_gpio_set_dir_flags(&phy_rst, GPIOD_IS_IN);
+ udelay(1000);
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ return mxs_dram_init();
+}
+
+#endif /* CONFIG_SPL_BUILD */
M: Martyn Welch <martyn.welch@collabora.com>
M: Parthiban Nallathambi <parthitce@gmail.com>
S: Maintained
-F: arch/arm/dts/imx6ul-pcl063.dtsi
-F: arch/arm/dts/imx6ul-phycore-segin.dts
-F: arch/arm/dts/imx6ull-phycore-segin.dts
-F: arch/arm/dts/pcl063-common.dtsi
+F: arch/arm/dts/imx6ul-phytec-phycore-som.dtsi
+F: arch/arm/dts/imx6ul-phytec-segin-peb-eval-01.dtsi
+F: arch/arm/dts/imx6ul-phytec-segin.dtsi
+F: arch/arm/dts/imx6ul-phytec-segin-ff-rdk-nand.dts
+F: arch/arm/dts/imx6ull-phytec-phycore-som.dtsi
+F: arch/arm/dts/imx6ull-phytec-segin-peb-eval-01.dtsi
+F: arch/arm/dts/imx6ull-phytec-segin.dtsi
+F: arch/arm/dts/imx6ull-phytec-segin-ff-rdk-emmc.dts
F: arch/arm/dts/imx6ull-u-boot.dtsi
F: board/phytec/pcl063/
F: configs/phycore_pcl063_defconfig
UNKNOWN = 0x03,
};
+static struct gpio_desc board_detect_desc[5];
+
#define MEM_STRIDE 0x4000000
static u32 get_ram_size_stride_test(u32 *base, u32 maxsize)
{
IOMUX_PADS(PAD_CSI0_DAT18__GPIO6_IO04 | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
-static iomux_v3_cfg_t const usb_pads[] = {
- IOMUX_PADS(PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
static void setup_iomux_uart(void)
{
SETUP_IOMUX_PADS(uart1_pads);
int board_mmc_get_env_dev(int devno)
{
- return devno - 1;
+ return devno;
}
#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4)
return ret;
}
-static int mmc_init_main(bd_t *bis)
-{
- int ret;
-
- /*
- * Following map is done:
- * (U-Boot device node) (Physical Port)
- * mmc0 Carrier board MicroSD
- * mmc1 SOM eMMC
- */
- SETUP_IOMUX_PADS(usdhc2_pads);
- usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg);
- if (ret)
- return ret;
-
- SETUP_IOMUX_PADS(usdhc3_pads);
- emmc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- return fsl_esdhc_initialize(bis, &emmc_cfg);
-}
-
static int mmc_init_spl(bd_t *bis)
{
struct src *psrc = (struct src *)SRC_BASE_ADDR;
if (IS_ENABLED(CONFIG_SPL_BUILD))
return mmc_init_spl(bis);
- return mmc_init_main(bis);
+ return 0;
}
static iomux_v3_cfg_t const enet_pads[] = {
static void setup_iomux_enet(void)
{
+ struct gpio_desc desc;
+ int ret;
+
SETUP_IOMUX_PADS(enet_pads);
+ ret = dm_gpio_lookup_name("GPIO4_15", &desc);
+ if (ret) {
+ printf("%s: phy reset lookup failed\n", __func__);
+ return;
+ }
+
+ ret = dm_gpio_request(&desc, "phy-reset");
+ if (ret) {
+ printf("%s: phy reset request failed\n", __func__);
+ return;
+ }
+
gpio_direction_output(ETH_PHY_RESET, 0);
mdelay(10);
gpio_set_value(ETH_PHY_RESET, 1);
udelay(100);
+
+ gpio_free_list_nodev(&desc, 1);
}
int board_phy_config(struct phy_device *phydev)
}
#endif /* CONFIG_VIDEO_IPUV3 */
-#ifdef CONFIG_USB_EHCI_MX6
-static void setup_usb(void)
-{
- SETUP_IOMUX_PADS(usb_pads);
-}
-
-int board_ehci_hcd_init(int port)
-{
- if (port == 1)
- gpio_direction_output(USB_H1_VBUS, 1);
-
- return 0;
-}
-#endif
-
int board_early_init_f(void)
{
setup_iomux_uart();
#ifdef CONFIG_CMD_SATA
setup_sata();
#endif
-
-#ifdef CONFIG_USB_EHCI_MX6
- setup_usb();
-#endif
return 0;
}
return ret;
}
+static int request_detect_gpios(void)
+{
+ int node;
+ int ret;
+
+ node = fdt_node_offset_by_compatible(gd->fdt_blob, 0,
+ "solidrun,hummingboard-detect");
+ if (node < 0)
+ return -ENODEV;
+
+ ret = gpio_request_list_by_name_nodev(offset_to_ofnode(node),
+ "detect-gpios", board_detect_desc,
+ ARRAY_SIZE(board_detect_desc), GPIOD_IS_IN);
+
+ return ret;
+}
+
+static int free_detect_gpios(void)
+{
+ return gpio_free_list_nodev(board_detect_desc,
+ ARRAY_SIZE(board_detect_desc));
+}
+
static enum board_type board_type(void)
{
int val1, val2, val3;
static bool has_emmc(void)
{
struct mmc *mmc;
- mmc = find_mmc_device(1);
+ mmc = find_mmc_device(2);
if (!mmc)
return 0;
return (mmc_get_op_cond(mmc) < 0) ? 0 : 1;
int checkboard(void)
{
+ request_detect_gpios();
+
switch (board_type()) {
case CUBOXI:
puts("Board: MX6 Cubox-i");
else
puts("\n");
+ free_detect_gpios();
out:
return 0;
}
+/* Override the default implementation, DT model is not accurate */
+int show_board_info(void)
+{
+ return checkboard();
+}
+
int board_late_init(void)
{
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ request_detect_gpios();
+
switch (board_type()) {
case CUBOXI:
env_set("board_name", "CUBOXI");
if (has_emmc())
env_set("has_emmc", "yes");
+ free_detect_gpios();
#endif
return 0;
}
+/*
+ * This is not a perfect match. Avoid dependency on the DM GPIO driver needed
+ * for accurate board detection. Hummingboard2 DT is good enough for U-Boot on
+ * all Hummingboard/Cubox-i platforms.
+ */
+int board_fit_config_name_match(const char *name)
+{
+ char tmp_name[36];
+
+ snprintf(tmp_name, sizeof(tmp_name), "%s-hummingboard2-emmc-som-v15",
+ is_mx6dq() ? "imx6q" : "imx6dl");
+
+ return strcmp(name, tmp_name);
+}
+
#ifdef CONFIG_SPL_BUILD
#include <asm/arch/mx6-ddr.h>
static const struct mx6dq_iomux_ddr_regs mx6q_ddr_ioregs = {
Apalis iMX6
-M: Max Krummenacher <max.krummenacher@toradex.com>
+M: Igor Opaniuk <igor.opaniuk@toradex.com>
W: http://developer.toradex.com/software/linux/linux-software
W: https://www.toradex.com/community
S: Maintained
# define GPIO_ENET_PHY_RESET IMX_GPIO_NR(1, 25)
};
-static void setup_iomux_enet(void)
-{
- imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
-}
-
-static int reset_enet_phy(struct mii_dev *bus)
-{
- /* Reset KSZ9031 PHY */
- gpio_request(GPIO_ENET_PHY_RESET, "ETH_RESET#");
- gpio_direction_output(GPIO_ENET_PHY_RESET, 0);
- mdelay(10);
- gpio_set_value(GPIO_ENET_PHY_RESET, 1);
-
- return 0;
-}
-
/* mux the Apalis GPIO pins, so they can be used from the U-Boot cmdline */
iomux_v3_cfg_t const gpio_pads[] = {
/* Apalis GPIO1 - GPIO8 */
return 0;
}
-int board_eth_init(bd_t *bis)
-{
- uint32_t base = IMX_FEC_BASE;
- struct mii_dev *bus = NULL;
- struct phy_device *phydev = NULL;
- int ret;
-
- setup_iomux_enet();
-
-#ifdef CONFIG_FEC_MXC
- bus = fec_get_miibus(base, -1);
- if (!bus)
- return 0;
-
- bus->reset = reset_enet_phy;
- /* scan PHY 4,5,6,7 */
- phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII);
- if (!phydev) {
- free(bus);
- puts("no PHY found\n");
- return 0;
- }
-
- printf("using PHY at %d\n", phydev->addr);
- ret = fec_probe(bis, -1, base, bus, phydev);
- if (ret) {
- printf("FEC MXC: %s:failed\n", __func__);
- free(phydev);
- free(bus);
- }
-#endif /* CONFIG_FEC_MXC */
-
- return 0;
-}
-
static iomux_v3_cfg_t const pwr_intb_pads[] = {
/*
* the bootrom sets the iomux to vselect, potentially connecting
Colibri iMX6ULL
-M: Stefan Agner <stefan.agner@toradex.com>
+M: Igor Opaniuk <igor.opaniuk@toradex.com>
W: http://developer.toradex.com/software/linux/linux-software
W: https://www.toradex.com/community
S: Maintained
Colibri iMX6
-M: Max Krummenacher <max.krummenacher@toradex.com>
+M: Igor Opaniuk <igor.opaniuk@toradex.com>
W: http://developer.toradex.com/software/linux/linux-software
W: https://www.toradex.com/community
S: Maintained
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
#define WEAK_PULLUP (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
PAD_CTL_SRE_SLOW)
};
#endif /* CONFIG_FSL_ESDHC_IMX & CONFIG_SPL_BUILD */
-iomux_v3_cfg_t const enet_pads[] = {
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_RX_ER__ENET_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
-
-static void setup_iomux_enet(void)
-{
- imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
-}
-
/* mux auxiliary pins to GPIO, so they can be used from the U-Boot cmdline */
iomux_v3_cfg_t const gpio_pads[] = {
/* ADDRESS[17:18] [25] used as GPIO */
return 0;
}
-int board_eth_init(bd_t *bis)
+int setup_fec(void)
{
- struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
- uint32_t base = IMX_FEC_BASE;
- struct mii_dev *bus = NULL;
- struct phy_device *phydev = NULL;
int ret;
/* provide the PHY clock from the i.MX 6 */
if (ret)
return ret;
- /* set gpr1[ENET_CLK_SEL] */
- setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
-
- setup_iomux_enet();
-
-#ifdef CONFIG_FEC_MXC
- bus = fec_get_miibus(base, -1);
- if (!bus)
- return 0;
-
- /* scan PHY 1..7 */
- phydev = phy_find_by_mask(bus, 0xff, PHY_INTERFACE_MODE_RMII);
- if (!phydev) {
- free(bus);
- puts("no PHY found\n");
- return 0;
- }
-
- phy_reset(phydev);
- printf("using PHY at %d\n", phydev->addr);
- ret = fec_probe(bis, -1, base, bus, phydev);
- if (ret) {
- printf("FEC MXC: %s:failed\n", __func__);
- free(phydev);
- free(bus);
- }
-#endif /* CONFIG_FEC_MXC */
-
return 0;
}
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
+#if defined(CONFIG_FEC_MXC)
+ setup_fec();
+#endif
#if defined(CONFIG_VIDEO_IPUV3)
setup_display();
#endif
Colibri iMX7
-M: Stefan Agner <stefan.agner@toradex.com>
+M: Igor Opaniuk <igor.opaniuk@toradex.com>
W: http://developer.toradex.com/software/linux/linux-software
W: https://www.toradex.com/community
S: Maintained
gpio_direction_output(GPIO_BL_ON, 0);
}
-#ifdef CONFIG_FEC_MXC
-static iomux_v3_cfg_t const fec1_pads[] = {
-#ifndef CONFIG_COLIBRI_IMX7_EXT_PHYCLK
- MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1 | MUX_PAD_CTRL(ENET_PAD_CTRL) | MUX_MODE_SION,
-#else
- MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-#endif
- MX7D_PAD_SD2_CD_B__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
- MX7D_PAD_SD2_WP__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
- MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_RXC__ENET1_RX_ER | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
-
-static void setup_iomux_fec(void)
-{
- imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
-}
-#endif
-
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
}
#ifdef CONFIG_FEC_MXC
-int board_eth_init(bd_t *bis)
-{
- int ret;
-
- setup_iomux_fec();
-
- ret = fecmxc_initialize_multi(bis, 0,
- CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
- if (ret)
- printf("FEC1 MXC: %s:failed\n", __func__);
-
- return ret;
-}
-
static int setup_fec(void)
{
struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
return set_clk_enet(ENET_50MHZ);
}
-int board_phy_config(struct phy_device *phydev)
-{
- if (phydev->drv->config)
- phydev->drv->config(phydev);
- return 0;
-}
#endif
int board_early_init_f(void)
Colibri T30
-M: Stefan Agner <stefan.agner@toradex.com>
+M: Igor Opaniuk <igor.opaniuk@toradex.com>
S: Maintained
F: board/toradex/colibri_t30/
F: include/configs/colibri_t30.h
Colibri VFxx
-M: Stefan Agner <stefan.agner@toradex.com>
+M: Igor Opaniuk <igor.opaniuk@toradex.com>
W: http://developer.toradex.com/software/linux/linux-software
W: https://www.toradex.com/community
S: Maintained
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_ARM=y
+CONFIG_SYS_THUMB_BUILD=y
CONFIG_ARCH_MX6=y
CONFIG_SYS_TEXT_BASE=0x17800000
+CONFIG_SYS_MALLOC_F_LEN=0xe000
CONFIG_TARGET_ARISTAINETOS2=y
CONFIG_ENV_SIZE=0x3000
CONFIG_ENV_OFFSET=0xD0000
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_IMX_HAB=y
+# CONFIG_CMD_DEKBLOB is not set
+# CONFIG_CMD_NANDBCB is not set
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/aristainetos/aristainetos2.cfg,MX6DL"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/aristainetos/aristainetos2.cfg"
CONFIG_BOOTDELAY=3
+CONFIG_USE_BOOTCOMMAND=y
+CONFIG_BOOTCOMMAND="run ari_boot"
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
CONFIG_SUPPORT_RAW_INITRD=y
+CONFIG_VERSION_VARIABLE=y
CONFIG_BOUNCE_BUFFER=y
+CONFIG_BOARD_TYPES=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_ENCRYPTION=y
+CONFIG_AUTOBOOT_STOP_STR_SHA256="30bb0bce5f77da71a6e8e436fe40af54bc823db9501ae170f77e9992499d88fb"
CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_BOOTM_VXWORKS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_NAND_TRIMFFS=y
-CONFIG_CMD_SF=y
+# CONFIG_CMD_PINMUX is not set
+# CONFIG_CMD_SATA is not set
CONFIG_CMD_USB=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
+# CONFIG_CMD_HASH is not set
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_CMD_MTDPARTS=y
CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6dl-aristainetos2_4"
+CONFIG_OF_LIST="imx6dl-aristainetos2_4 imx6dl-aristainetos2_7"
+CONFIG_DTB_RESELECT=y
+CONFIG_MULTI_DTB_FIT=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_ENV_SPI_EARLY=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_OFFSET_REDUND=0xE0000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_GPIO=y
+CONFIG_GPIO_HOG=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_MISC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_DM_MMC=y
CONFIG_FSL_USDHC=y
CONFIG_MTD=y
CONFIG_MTD_RAW_NAND=y
CONFIG_NAND_MXS=y
-CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SF_DEFAULT_BUS=3
CONFIG_SF_DEFAULT_CS=1
CONFIG_SF_DEFAULT_MODE=0
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
+CONFIG_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_PWM=y
CONFIG_PWM_IMX=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_DS1307=y
+CONFIG_DM_SERIAL=y
CONFIG_SPI=y
+CONFIG_DM_SPI=y
CONFIG_MXC_SPI=y
+CONFIG_SYSRESET=y
+CONFIG_SYSRESET_WATCHDOG=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
+CONFIG_DM_VIDEO=y
+CONFIG_SYS_WHITE_ON_BLACK=y
+CONFIG_DISPLAY=y
CONFIG_VIDEO_IPUV3=y
-CONFIG_VIDEO=y
-# CONFIG_VIDEO_SW_CURSOR is not set
CONFIG_IMX_WATCHDOG=y
-CONFIG_OF_LIBFDT=y
+# CONFIG_EFI_LOADER is not set
CONFIG_ARM=y
+CONFIG_SYS_THUMB_BUILD=y
CONFIG_ARCH_MX6=y
CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_TARGET_ARISTAINETOS2B=y
+CONFIG_SYS_MALLOC_F_LEN=0xe000
CONFIG_ENV_SIZE=0x3000
CONFIG_ENV_OFFSET=0xD0000
+CONFIG_TARGET_ARISTAINETOS2B=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_IMX_HAB=y
+# CONFIG_CMD_DEKBLOB is not set
+# CONFIG_CMD_NANDBCB is not set
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/aristainetos/aristainetos2.cfg,MX6DL"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/aristainetos/aristainetos2.cfg"
CONFIG_BOOTDELAY=3
+CONFIG_USE_BOOTCOMMAND=y
+CONFIG_BOOTCOMMAND="run ari_boot"
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
CONFIG_SUPPORT_RAW_INITRD=y
+CONFIG_VERSION_VARIABLE=y
CONFIG_BOUNCE_BUFFER=y
+CONFIG_BOARD_TYPES=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_ENCRYPTION=y
+CONFIG_AUTOBOOT_STOP_STR_SHA256="30bb0bce5f77da71a6e8e436fe40af54bc823db9501ae170f77e9992499d88fb"
CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_BOOTM_VXWORKS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_NAND_TRIMFFS=y
-CONFIG_CMD_SF=y
+# CONFIG_CMD_PINMUX is not set
+# CONFIG_CMD_SATA is not set
CONFIG_CMD_USB=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
+# CONFIG_CMD_HASH is not set
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_CMD_MTDPARTS=y
CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6dl-aristainetos2b_4"
+CONFIG_OF_LIST="imx6dl-aristainetos2b_4 imx6dl-aristainetos2b_7"
+CONFIG_DTB_RESELECT=y
+CONFIG_MULTI_DTB_FIT=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_ENV_SPI_EARLY=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_OFFSET_REDUND=0xE0000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_GPIO=y
+CONFIG_GPIO_HOG=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_MISC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_DM_MMC=y
CONFIG_FSL_USDHC=y
CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
+CONFIG_NAND=y
CONFIG_NAND_MXS=y
-CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=20000000
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
+CONFIG_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_PWM=y
CONFIG_PWM_IMX=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_DS1307=y
+CONFIG_DM_SERIAL=y
CONFIG_SPI=y
+CONFIG_DM_SPI=y
CONFIG_MXC_SPI=y
+CONFIG_SYSRESET=y
+CONFIG_SYSRESET_WATCHDOG=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
+CONFIG_DM_VIDEO=y
+CONFIG_SYS_WHITE_ON_BLACK=y
+CONFIG_DISPLAY=y
CONFIG_VIDEO_IPUV3=y
-CONFIG_VIDEO=y
-# CONFIG_VIDEO_SW_CURSOR is not set
CONFIG_IMX_WATCHDOG=y
-CONFIG_OF_LIBFDT=y
+# CONFIG_EFI_LOADER is not set
--- /dev/null
+CONFIG_ARM=y
+CONFIG_SYS_THUMB_BUILD=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x17800000
+CONFIG_SYS_MALLOC_F_LEN=0xe000
+CONFIG_ENV_SIZE=0x3000
+CONFIG_ENV_OFFSET=0xD0000
+CONFIG_TARGET_ARISTAINETOS2BCSL=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_IMX_HAB=y
+# CONFIG_CMD_DEKBLOB is not set
+# CONFIG_CMD_NANDBCB is not set
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/aristainetos/aristainetos2.cfg"
+CONFIG_BOOTDELAY=3
+CONFIG_USE_BOOTCOMMAND=y
+CONFIG_BOOTCOMMAND="run ari_boot"
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_SUPPORT_RAW_INITRD=y
+CONFIG_VERSION_VARIABLE=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_BOARD_TYPES=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_HUSH_PARSER=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_ENCRYPTION=y
+CONFIG_AUTOBOOT_STOP_STR_SHA256="30bb0bce5f77da71a6e8e436fe40af54bc823db9501ae170f77e9992499d88fb"
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_BOOTM_VXWORKS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_NAND_TRIMFFS=y
+# CONFIG_CMD_PINMUX is not set
+# CONFIG_CMD_SATA is not set
+CONFIG_CMD_USB=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_BMP=y
+CONFIG_CMD_CACHE=y
+# CONFIG_CMD_HASH is not set
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6dl-aristainetos2b_csl_4"
+CONFIG_OF_LIST="imx6dl-aristainetos2b_csl_4 imx6dl-aristainetos2b_csl_7"
+CONFIG_DTB_RESELECT=y
+CONFIG_MULTI_DTB_FIT=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_ENV_SPI_EARLY=y
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_ENV_OFFSET_REDUND=0xE0000
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_GPIO=y
+CONFIG_GPIO_HOG=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_MISC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_MTD=y
+CONFIG_NAND=y
+CONFIG_NAND_MXS=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SF_DEFAULT_MODE=0
+CONFIG_SF_DEFAULT_SPEED=20000000
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_MTD_UBI_FASTMAP=y
+CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT=1
+CONFIG_PHYLIB=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
+CONFIG_MII=y
+CONFIG_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_PWM=y
+CONFIG_PWM_IMX=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_DS1307=y
+CONFIG_DM_SERIAL=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_MXC_SPI=y
+CONFIG_SYSRESET=y
+CONFIG_SYSRESET_WATCHDOG=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_DM_VIDEO=y
+CONFIG_SYS_WHITE_ON_BLACK=y
+CONFIG_DISPLAY=y
+CONFIG_VIDEO_IPUV3=y
+CONFIG_IMX_WATCHDOG=y
+# CONFIG_EFI_LOADER is not set
--- /dev/null
+CONFIG_ARM=y
+CONFIG_SYS_THUMB_BUILD=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x17800000
+CONFIG_SYS_MALLOC_F_LEN=0xe000
+CONFIG_ENV_SIZE=0x3000
+CONFIG_ENV_OFFSET=0xD0000
+CONFIG_TARGET_ARISTAINETOS2C=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_IMX_HAB=y
+# CONFIG_CMD_DEKBLOB is not set
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/aristainetos/aristainetos2.cfg"
+CONFIG_BOOTDELAY=3
+CONFIG_USE_BOOTCOMMAND=y
+CONFIG_BOOTCOMMAND="run ari_boot"
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_SUPPORT_RAW_INITRD=y
+CONFIG_VERSION_VARIABLE=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_BOARD_TYPES=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_HUSH_PARSER=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_ENCRYPTION=y
+CONFIG_AUTOBOOT_STOP_STR_SHA256="30bb0bce5f77da71a6e8e436fe40af54bc823db9501ae170f77e9992499d88fb"
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_BOOTM_VXWORKS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+# CONFIG_CMD_PINMUX is not set
+# CONFIG_CMD_SATA is not set
+CONFIG_CMD_USB=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_BMP=y
+CONFIG_CMD_CACHE=y
+# CONFIG_CMD_HASH is not set
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6dl-aristainetos2c_4"
+CONFIG_OF_LIST="imx6dl-aristainetos2c_4 imx6dl-aristainetos2c_7"
+CONFIG_DTB_RESELECT=y
+CONFIG_MULTI_DTB_FIT=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_ENV_SPI_EARLY=y
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_ENV_OFFSET_REDUND=0xE0000
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_APBH_DMA=y
+CONFIG_APBH_DMA_BURST=y
+CONFIG_APBH_DMA_BURST8=y
+CONFIG_DM_GPIO=y
+CONFIG_GPIO_HOG=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_MISC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_MTD=y
+CONFIG_MTD_DEVICE=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SF_DEFAULT_MODE=0
+CONFIG_SF_DEFAULT_SPEED=20000000
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_MTD_UBI_FASTMAP=y
+CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT=1
+CONFIG_PHYLIB=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
+CONFIG_MII=y
+CONFIG_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_PWM=y
+CONFIG_PWM_IMX=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_DS1307=y
+CONFIG_DM_SERIAL=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_MXC_SPI=y
+CONFIG_SYSRESET=y
+CONFIG_SYSRESET_WATCHDOG=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_DM_VIDEO=y
+CONFIG_SYS_WHITE_ON_BLACK=y
+CONFIG_DISPLAY=y
+CONFIG_VIDEO_IPUV3=y
+CONFIG_IMX_WATCHDOG=y
+# CONFIG_EFI_LOADER is not set
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_TARGET_ARISTAINETOS=y
-CONFIG_ENV_SIZE=0x3000
-CONFIG_ENV_OFFSET=0xD0000
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/aristainetos/aristainetos.cfg,MX6DL"
-CONFIG_BOOTDELAY=3
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND_TRIMFFS=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_CMD_UBI=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_ENV_OFFSET_REDUND=0xE0000
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_FSL_USDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_MXS=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_BUS=3
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=20000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_MTD=y
-CONFIG_MTD_UBI_FASTMAP=y
-CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT=1
-CONFIG_PHYLIB=y
-CONFIG_PHY_MICREL=y
-CONFIG_PHY_MICREL_KSZ8XXX=y
-CONFIG_MII=y
-CONFIG_PWM_IMX=y
-CONFIG_SPI=y
-CONFIG_MXC_SPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_VIDEO_IPUV3=y
-CONFIG_VIDEO=y
-# CONFIG_VIDEO_SW_CURSOR is not set
-CONFIG_IMX_WATCHDOG=y
-CONFIG_OF_LIBFDT=y
CONFIG_MTD_RAW_NAND=y
CONFIG_NAND_MXS=y
CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=25000000
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_DM_PMIC=y
CONFIG_DM_REGULATOR=y
CONFIG_SPI=y
+CONFIG_DM_SPI=y
CONFIG_MXC_SPI=y
+CONFIG_DM_ETH=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_KEYBOARD=y
CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
CONFIG_VIDEO_IPUV3=y
CONFIG_VIDEO=y
+CONFIG_DM_VIDEO=y
CONFIG_FDT_FIXUP_PARTITIONS=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ8XXX=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ8XXX=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX7=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ8XXX=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX7=y
CONFIG_CMD_SATA=y
CONFIG_CMD_USB=y
CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_WDT=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_TIME=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_MXC_SPI=y
+CONFIG_SYSRESET=y
+CONFIG_SYSRESET_WATCHDOG=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_GADGET=y
CONFIG_BOOTDELAY=1
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
CONFIG_SUPPORT_RAW_INITRD=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_LAST_STAGE_INIT=y
CONFIG_DOS_PARTITION=y
CONFIG_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="imx6q-bx50v3"
+CONFIG_OF_LIST="imx6q-bx50v3 imx6q-b850v3 imx6q-b650v3 imx6q-b450v3"
+CONFIG_DTB_RESELECT=y
+CONFIG_MULTI_DTB_FIT=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
CONFIG_VIDEO_IPUV3=y
CONFIG_WATCHDOG_TIMEOUT_MSECS=6000
CONFIG_IMX_WATCHDOG=y
+CONFIG_WDT=y
+CONFIG_SYSRESET=y
+CONFIG_SYSRESET_WATCHDOG=y
# CONFIG_EFI_LOADER is not set
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_SYS_WHITE_ON_BLACK=y
+CONFIG_PCI=y
+CONFIG_DM_PCI=y
+CONFIG_PCI_PNP=y
+CONFIG_DM_ETH=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_FEC_MXC=y
+CONFIG_ETHPRIME="FEC"
--- /dev/null
+CONFIG_ARM=y
+CONFIG_SPL_SYS_THUMB_BUILD=y
+CONFIG_ARCH_MX28=y
+CONFIG_SYS_TEXT_BASE=0x40002000
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x800
+CONFIG_SPL_DM_SPI=y
+CONFIG_TARGET_XEA=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_SYS_MALLOC_F_LEN=0x1000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_SPL=y
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_SPL_TEXT_BASE=0x1000
+CONFIG_FIT=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_BOARD_INIT=y
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0
+CONFIG_SUPPORT_EMMC_BOOT_OVERRIDE_PART_CONFIG=y
+CONFIG_SPL_DMA_SUPPORT=y
+CONFIG_SPL_DM_GPIO=y
+CONFIG_SPL_FORCE_MMC_BOOT=y
+CONFIG_SPL_MMC_TINY=y
+CONFIG_SPL_OS_BOOT=y
+CONFIG_SPL_PAYLOAD="u-boot.img"
+CONFIG_SPL_SPI_LOAD=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_SPL=y
+CONFIG_CMD_ASKENV=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+# CONFIG_CMD_PINMUX is not set
+CONFIG_CMD_SPI=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nor0=spi3.0"
+CONFIG_MTDPARTS_DEFAULT="spi3.0:64k(SPL),448k(uboot),128k(envs),384k(unused1),4096k(kernel),8192k(swupdate),-(unused2)"
+CONFIG_DOS_PARTITION=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx28-xea"
+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent interrupts"
+CONFIG_SPL_OF_PLATDATA=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_USE_ENV_SPI_BUS=y
+CONFIG_ENV_SPI_BUS=3
+CONFIG_USE_ENV_SPI_CS=y
+CONFIG_ENV_SPI_CS=0
+CONFIG_USE_ENV_SPI_MAX_HZ=y
+CONFIG_ENV_SPI_MAX_HZ=40000000
+CONFIG_USE_ENV_SPI_MODE=y
+CONFIG_ENV_SPI_MODE=0x0
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_SPL_DM=y
+CONFIG_DEVRES=y
+CONFIG_DM_GPIO=y
+CONFIG_MXS_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_MMC_MXS=y
+CONFIG_MTD=y
+CONFIG_MTD_DEVICE=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SF_DEFAULT_BUS=3
+CONFIG_SF_DEFAULT_MODE=0x0
+CONFIG_SF_DEFAULT_SPEED=40000000
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_ISSI=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHYLIB=y
+CONFIG_PHY_ADDR_ENABLE=y
+CONFIG_PHY_ADDR=1
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MXS=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_CONS_INDEX=0
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_MXS_SPI=y
+CONFIG_FS_FAT=y
+# CONFIG_SPL_OF_LIBFDT is not set
+# CONFIG_EFI_LOADER is not set
CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
CONFIG_OF_SYSTEM_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/imx8m/imximage-8mm-lpddr4.cfg"
-CONFIG_DEFAULT_FDT_FILE="fsl-imx8mm-evk.dtb"
CONFIG_BOARD_LATE_INIT=y
CONFIG_SPL_BOARD_INIT=y
CONFIG_SPL_SEPARATE_BSS=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/beckhoff/mx53cx9020/imximage.cfg"
CONFIG_BOOTDELAY=1
CONFIG_USE_PREBOOT=y
+CONFIG_DISTRO_DEFAULTS=y
CONFIG_SUPPORT_RAW_INITRD=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
+CONFIG_CMD_USB=y
CONFIG_CMD_FS_GENERIC=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_MX5=y
+CONFIG_USB_STORAGE=y
+CONFIG_DM_REGULATOR=y
CONFIG_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="imx53-cx9020"
CONFIG_ENV_IS_IN_MMC=y
CONFIG_DM_GPIO=y
CONFIG_DM_MMC=y
CONFIG_FSL_ESDHC_IMX=y
+CONFIG_DM_ETH=y
CONFIG_MTD=y
CONFIG_FEC_MXC=y
+CONFIG_PHYLIB=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX5=y
CONFIG_DM_VIDEO=y
CONFIG_VIDEO_BPP16=y
CONFIG_VIDEO_IPUV3=y
+CONFIG_SYS_WHITE_ON_BLACK=y
# CONFIG_VIDEO_SW_CURSOR is not set
CONFIG_WATCHDOG_TIMEOUT_MSECS=8000
CONFIG_IMX_WATCHDOG=y
+CONFIG_WDT=y
+CONFIG_SYSRESET=y
+CONFIG_SYSRESET_WATCHDOG=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_USB=y
CONFIG_SPL_LIBDISK_SUPPORT=y
# CONFIG_CMD_BMODE is not set
CONFIG_CMD_HDMIDETECT=y
+CONFIG_AHCI=y
CONFIG_SPL_TEXT_BASE=0x00908000
CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
CONFIG_BOOTCOMMAND="run findfdt; run finduuid; run distro_bootcmd"
CONFIG_USE_PREBOOT=y
CONFIG_SPL_WATCHDOG_SUPPORT=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_MMC=y
+# CONFIG_CMD_PINMUX is not set
CONFIG_CMD_SATA=y
CONFIG_CMD_USB=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_EXT4_WRITE=y
# CONFIG_SPL_PARTITION_UUIDS is not set
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6dl-hummingboard2-emmc-som-v15"
+CONFIG_OF_LIST="imx6dl-hummingboard2-emmc-som-v15 imx6q-hummingboard2-emmc-som-v15"
+CONFIG_MULTI_DTB_FIT=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_DWC_AHSATA=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_MMC=y
CONFIG_FSL_USDHC=y
CONFIG_PHYLIB=y
CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_THERMAL=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_KEYBOARD=y
CONFIG_VIDEO_IPUV3=y
CONFIG_VIDEO=y
# CONFIG_VIDEO_SW_CURSOR is not set
-CONFIG_OF_LIBFDT=y
# CONFIG_ARMV7_VIRT is not set
CONFIG_IMX_RDC=y
CONFIG_IMX_BOOTAUX=y
+CONFIG_DISTRO_DEFAULTS=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7dsabresd/imximage.cfg"
+CONFIG_BOOTCOMMAND="run finduuid; run distro_bootcmd"
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_BOUNCE_BUFFER=y
-CONFIG_HUSH_PARSER=y
# CONFIG_CMD_BOOTD is not set
-CONFIG_CMD_BOOTZ=y
# CONFIG_BOOTM_NETBSD is not set
# CONFIG_BOOTM_PLAN9 is not set
# CONFIG_BOOTM_RTEMS is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_USB=y
CONFIG_CMD_USB_MASS_STORAGE=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_PMIC=y
CONFIG_CMD_REGULATOR=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
+# CONFIG_ISO_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
CONFIG_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="imx7d-sdb"
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_MMC_UHS_SUPPORT=y
CONFIG_MMC_HS200_SUPPORT=y
CONFIG_FSL_USDHC=y
-CONFIG_MTD=y
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_EON=y
CONFIG_PHYLIB=y
+CONFIG_PHY_BROADCOM=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_DM_MDIO_MUX=y
+CONFIG_FEC_MXC=y
+CONFIG_RGMII=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX7=y
CONFIG_DM_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_MXC_USB_OTG_HACTIVE=y
-CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_MANUFACTURER="FSL"
CONFIG_USB_GADGET_VENDOR_NUM=0x0525
CONFIG_TARGET_MX7DSABRESD=y
CONFIG_ENV_SIZE=0x2000
CONFIG_ENV_OFFSET=0xC0000
+CONFIG_NR_DRAM_BANKS=1
CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
# CONFIG_ARMV7_VIRT is not set
CONFIG_IMX_RDC=y
CONFIG_IMX_BOOTAUX=y
+CONFIG_DISTRO_DEFAULTS=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7dsabresd/imximage.cfg"
+CONFIG_BOOTCOMMAND="run finduuid; run distro_bootcmd"
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_BOUNCE_BUFFER=y
-CONFIG_HUSH_PARSER=y
# CONFIG_CMD_BOOTD is not set
-CONFIG_CMD_BOOTZ=y
# CONFIG_BOOTM_NETBSD is not set
# CONFIG_BOOTM_PLAN9 is not set
# CONFIG_BOOTM_RTEMS is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_USB=y
CONFIG_CMD_USB_MASS_STORAGE=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_PMIC=y
CONFIG_CMD_REGULATOR=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
+# CONFIG_ISO_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
CONFIG_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="imx7d-sdb-qspi"
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SPI_FLASH_EON=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_PHYLIB=y
+CONFIG_PHY_BROADCOM=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_DM_MDIO_MUX=y
+CONFIG_FEC_MXC=y
+CONFIG_RGMII=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX7=y
CONFIG_DM_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_MXC_USB_OTG_HACTIVE=y
-CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_MANUFACTURER="FSL"
CONFIG_USB_GADGET_VENDOR_NUM=0x0525
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MX7ULP=y
+CONFIG_SYS_TEXT_BASE=0x67800000
+CONFIG_LDO_ENABLED_MODE=y
+CONFIG_TARGET_MX7ULP_COM=y
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0xC0000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/ea/mx7ulp_com/imximage.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx7ulp-com"
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_READ=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx7ulp-com"
+CONFIG_ENV_IS_IN_MMC=y
+# CONFIG_NET is not set
+CONFIG_DM=y
+CONFIG_DM_GPIO=y
+CONFIG_IMX_RGPIO2P=y
+# CONFIG_MXC_GPIO is not set
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_IMX_LPI2C=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SF_DEFAULT_MODE=0
+CONFIG_SF_DEFAULT_SPEED=40000000
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX7ULP=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_SERIAL=y
+CONFIG_FSL_LPUART=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_ULP_WATCHDOG=y
CONFIG_CMD_UBI=y
# CONFIG_ISO_PARTITION is not set
CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="imx6ul-phycore-segin"
+CONFIG_DEFAULT_DEVICE_TREE="imx6ul-phytec-segin-ff-rdk-nand"
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM_I2C_GPIO=y
CONFIG_SYS_I2C_MXC=y
CONFIG_CMD_CACHE=y
# CONFIG_ISO_PARTITION is not set
CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="imx6ull-phycore-segin"
+CONFIG_DEFAULT_DEVICE_TREE="imx6ull-phytec-segin-ff-rdk-emmc"
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM_I2C_GPIO=y
CONFIG_SYS_I2C_MXC=y
}
}
-void ddr_init(struct dram_timing_info *dram_timing)
+int ddr_init(struct dram_timing_info *dram_timing)
{
unsigned int tmp, initial_drate, target_freq;
+ int ret;
debug("DDRINFO: start DRAM init\n");
* accessing relevant PUB registers
*/
debug("DDRINFO:ddrphy config start\n");
- ddr_cfg_phy(dram_timing);
+
+ ret = ddr_cfg_phy(dram_timing);
+ if (ret)
+ return ret;
+
debug("DDRINFO: ddrphy config done\n");
/*
/* save the dram timing config into memory */
dram_config_save(dram_timing, CONFIG_SAVED_DRAM_TIMING_BASE);
+
+ return 0;
}
#include <asm/arch/ddr.h>
#include <asm/arch/lpddr4_define.h>
-void ddr_cfg_phy(struct dram_timing_info *dram_timing)
+int ddr_cfg_phy(struct dram_timing_info *dram_timing)
{
struct dram_cfg_param *dram_cfg;
struct dram_fsp_msg *fsp_msg;
unsigned int num;
int i = 0;
int j = 0;
+ int ret;
/* initialize PHY configuration */
dram_cfg = dram_timing->ddrphy_cfg;
dwc_ddrphy_apb_wr(0xd0099, 0x0);
/* Wait for the training firmware to complete */
- wait_ddrphy_training_complete();
+ ret = wait_ddrphy_training_complete();
+ if (ret)
+ return ret;
/* Halt the microcontroller. */
dwc_ddrphy_apb_wr(0xd0099, 0x1);
/* save the ddr PHY trained CSR in memory for low power use */
ddrphy_trained_csr_save(ddrphy_trained_csr, ddrphy_trained_csr_num);
+
+ return 0;
}
debug("\n");
}
-void wait_ddrphy_training_complete(void)
+int wait_ddrphy_training_complete(void)
{
unsigned int mail;
decode_streaming_message();
} else if (mail == 0x07) {
debug("Training PASS\n");
- break;
+ return 0;
} else if (mail == 0xff) {
- printf("Training FAILED\n");
- break;
+ debug("Training FAILED\n");
+ return -1;
}
}
}
static const struct udevice_id imx_pcie_ids[] = {
{ .compatible = "fsl,imx6q-pcie" },
+ { .compatible = "fsl,imx6sx-pcie" },
{ }
};
*
*/
#include <common.h>
+#include <backlight.h>
+#include <display.h>
+#include <dm.h>
+#include <dm/read.h>
+#include <dm/uclass-internal.h>
#include <errno.h>
#include <spi.h>
+#include <asm/gpio.h>
#define PWR_ON_DELAY_MSECS 120
-static int lb043wv_spi_write_u16(struct spi_slave *spi, u16 val)
+static int lb043wv_spi_write_u16(struct spi_slave *slave, u16 val)
{
- unsigned long flags = SPI_XFER_BEGIN;
unsigned short buf16 = htons(val);
int ret = 0;
- flags |= SPI_XFER_END;
-
- ret = spi_xfer(spi, 16, &buf16, NULL, flags);
+ ret = spi_xfer(slave, 16, &buf16, NULL,
+ SPI_XFER_BEGIN | SPI_XFER_END);
if (ret)
debug("%s: Failed to send: %d\n", __func__, ret);
return ret;
}
-static void lb043wv_spi_write_u16_array(struct spi_slave *spi, u16 *buff,
+static void lb043wv_spi_write_u16_array(struct spi_slave *slave, u16 *buff,
int size)
{
int i;
for (i = 0; i < size; i++)
- lb043wv_spi_write_u16(spi, buff[i]);
+ lb043wv_spi_write_u16(slave, buff[i]);
}
-static void lb043wv_display_mode_settings(struct spi_slave *spi)
+static void lb043wv_display_mode_settings(struct spi_slave *slave)
{
static u16 display_mode_settings[] = {
0x703A,
};
debug("transfer display mode settings\n");
- lb043wv_spi_write_u16_array(spi, display_mode_settings,
+ lb043wv_spi_write_u16_array(slave, display_mode_settings,
ARRAY_SIZE(display_mode_settings));
}
-static void lb043wv_power_settings(struct spi_slave *spi)
+static void lb043wv_power_settings(struct spi_slave *slave)
{
static u16 power_settings[] = {
0x70C0,
};
debug("transfer power settings\n");
- lb043wv_spi_write_u16_array(spi, power_settings,
+ lb043wv_spi_write_u16_array(slave, power_settings,
ARRAY_SIZE(power_settings));
}
-static void lb043wv_gamma_settings(struct spi_slave *spi)
+static void lb043wv_gamma_settings(struct spi_slave *slave)
{
static u16 gamma_settings[] = {
0x70D0,
};
debug("transfer gamma settings\n");
- lb043wv_spi_write_u16_array(spi, gamma_settings,
+ lb043wv_spi_write_u16_array(slave, gamma_settings,
ARRAY_SIZE(gamma_settings));
}
-static void lb043wv_display_on(struct spi_slave *spi)
+static void lb043wv_display_on(struct spi_slave *slave)
{
static u16 sleep_out = 0x7011;
static u16 display_on = 0x7029;
- lb043wv_spi_write_u16(spi, sleep_out);
+ lb043wv_spi_write_u16(slave, sleep_out);
mdelay(PWR_ON_DELAY_MSECS);
- lb043wv_spi_write_u16(spi, display_on);
+ lb043wv_spi_write_u16(slave, display_on);
}
-int lg4573_spi_startup(unsigned int bus, unsigned int cs,
- unsigned int max_hz, unsigned int spi_mode)
+static int lg4573_spi_startup(struct spi_slave *slave)
{
- struct spi_slave *spi;
int ret;
- spi = spi_setup_slave(bus, cs, max_hz, spi_mode);
- if (!spi) {
- debug("%s: Failed to set up slave\n", __func__);
- return -1;
- }
-
- ret = spi_claim_bus(spi);
- if (ret) {
- debug("%s: Failed to claim SPI bus: %d\n", __func__, ret);
- goto err_claim_bus;
- }
+ ret = spi_claim_bus(slave);
+ if (ret)
+ return ret;
- lb043wv_display_mode_settings(spi);
- lb043wv_power_settings(spi);
- lb043wv_gamma_settings(spi);
+ lb043wv_display_mode_settings(slave);
+ lb043wv_power_settings(slave);
+ lb043wv_gamma_settings(slave);
+ lb043wv_display_on(slave);
- lb043wv_display_on(spi);
+ spi_release_bus(slave);
return 0;
-err_claim_bus:
- spi_free_slave(spi);
- return -1;
}
static int do_lgset(cmd_tbl_t *cmdtp, int flag, int argc,
char * const argv[])
{
- lg4573_spi_startup(CONFIG_LG4573_BUS, CONFIG_LG4573_CS, 10000000,
- SPI_MODE_0);
+ struct spi_slave *slave;
+ struct udevice *dev;
+ int ret;
+
+ ret = uclass_get_device_by_driver(UCLASS_DISPLAY,
+ DM_GET_DRIVER(lg4573_lcd), &dev);
+ if (ret) {
+ printf("%s: Could not get lg4573 device\n", __func__);
+ return ret;
+ }
+ slave = dev_get_parent_priv(dev);
+ if (!slave) {
+ printf("%s: No slave data\n", __func__);
+ return -ENODEV;
+ }
+ lg4573_spi_startup(slave);
+
return 0;
}
"set lgdisplay",
""
);
+
+static int lg4573_bind(struct udevice *dev)
+{
+ return 0;
+}
+
+static int lg4573_probe(struct udevice *dev)
+{
+ return 0;
+}
+
+static const struct udevice_id lg4573_ids[] = {
+ { .compatible = "lg,lg4573" },
+ { }
+};
+
+struct lg4573_lcd_priv {
+ struct display_timing timing;
+ struct udevice *backlight;
+ struct gpio_desc enable;
+ int panel_bpp;
+ u32 power_on_delay;
+};
+
+static int lg4573_lcd_read_timing(struct udevice *dev,
+ struct display_timing *timing)
+{
+ struct lg4573_lcd_priv *priv = dev_get_priv(dev);
+
+ memcpy(timing, &priv->timing, sizeof(struct display_timing));
+
+ return 0;
+}
+
+static int lg4573_lcd_enable(struct udevice *dev, int bpp,
+ const struct display_timing *edid)
+{
+ struct spi_slave *slave = dev_get_parent_priv(dev);
+ struct lg4573_lcd_priv *priv = dev_get_priv(dev);
+ int ret = 0;
+
+ dm_gpio_set_value(&priv->enable, 1);
+ ret = backlight_enable(priv->backlight);
+
+ mdelay(priv->power_on_delay);
+ lg4573_spi_startup(slave);
+
+ return ret;
+};
+
+static const struct dm_display_ops lg4573_lcd_ops = {
+ .read_timing = lg4573_lcd_read_timing,
+ .enable = lg4573_lcd_enable,
+};
+
+static int lg4573_ofdata_to_platdata(struct udevice *dev)
+{
+ struct lg4573_lcd_priv *priv = dev_get_priv(dev);
+ int ret;
+
+ ret = uclass_get_device_by_phandle(UCLASS_PANEL_BACKLIGHT, dev,
+ "backlight", &priv->backlight);
+ if (ret) {
+ debug("%s: Cannot get backlight: ret=%d\n", __func__, ret);
+ return log_ret(ret);
+ }
+ ret = gpio_request_by_name(dev, "enable-gpios", 0, &priv->enable,
+ GPIOD_IS_OUT);
+ if (ret) {
+ debug("%s: Warning: cannot get enable GPIO: ret=%d\n",
+ __func__, ret);
+ if (ret != -ENOENT)
+ return log_ret(ret);
+ }
+
+ priv->power_on_delay = dev_read_u32_default(dev, "power-on-delay", 10);
+
+ return 0;
+}
+
+U_BOOT_DRIVER(lg4573_lcd) = {
+ .name = "lg4573",
+ .id = UCLASS_DISPLAY,
+ .ops = &lg4573_lcd_ops,
+ .ofdata_to_platdata = lg4573_ofdata_to_platdata,
+ .of_match = lg4573_ids,
+ .bind = lg4573_bind,
+ .probe = lg4573_probe,
+ .priv_auto_alloc_size = sizeof(struct lg4573_lcd_priv),
+};
#endif
/* Network */
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
#define PHY_ANEG_TIMEOUT 15000 /* PHY needs longer aneg time */
-#define CONFIG_FEC_MXC_PHYADDR 6
-#define CONFIG_TFTP_TSIZE
/* USB Configs */
/* Host */
"imx6q-apalis-eval.dtb fat 0 1;" \
"imx6q-apalis-cam-eval.dtb fat 0 1"
+#define UBOOT_UPDATE \
+ "uboot_hwpart=1\0" \
+ "uboot_blk=8a\0" \
+ "uboot_spl_blk=2\0" \
+ "set_blkcnt=setexpr blkcnt ${filesize} + 0x1ff && " \
+ "setexpr blkcnt ${blkcnt} / 0x200\0" \
+ "update_uboot=run set_blkcnt && mmc dev 0 ${uboot_hwpart} && " \
+ "mmc write ${loadaddr} ${uboot_blk} ${blkcnt}\0" \
+ "update_spl=run set_blkcnt && mmc dev 0 ${uboot_hwpart} && " \
+ "mmc write ${loadaddr} ${uboot_spl_blk} ${blkcnt}\0"
+
#define EMMC_BOOTCMD \
"set_emmcargs=setenv emmcargs ip=off root=PARTUUID=${uuid} " \
"ro,noatime rootfstype=ext4 rootwait\0" \
"fdt_fixup=;\0" \
MEM_LAYOUT_ENV_SETTINGS \
NFS_BOOTCMD \
+ UBOOT_UPDATE \
"setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
"00:14:2d:00:00:00; fi; tftpboot ${loadaddr} " \
"flash_eth.img && source ${loadaddr}\0" \
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2015
- * (C) Copyright 2014
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * Based on:
- * Copyright (C) 2012 Freescale Semiconductor, Inc.
- *
- * Configuration settings for the Freescale i.MX6Q SabreSD board.
- */
-#ifndef __ARISTAINETOS_COMMON_CONFIG_H
-#define __ARISTAINETOS_COMMON_CONFIG_H
-
-#include "mx6_common.h"
-
-#define CONFIG_MACH_TYPE 4501
-#define CONFIG_MMCROOT "/dev/mmcblk0p1"
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (64 * SZ_1M)
-
-#define CONFIG_MXC_UART
-
-/* MMC Configs */
-#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_MXC_PHYADDR 0
-
-#define CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "script=u-boot.scr\0" \
- "fit_file=/boot/system.itb\0" \
- "loadaddr=0x12000000\0" \
- "fit_addr_r=0x14000000\0" \
- "uboot=/boot/u-boot.imx\0" \
- "uboot_sz=d0000\0" \
- "rescue_sys_addr=f0000\0" \
- "rescue_sys_length=f10000\0" \
- "panel=lb07wv8\0" \
- "splashpos=m,m\0" \
- "console=" CONSOLE_DEV "\0" \
- "fdt_high=0xffffffff\0" \
- "initrd_high=0xffffffff\0" \
- "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "set_fit_default=fdt addr ${fit_addr_r};fdt set /configurations " \
- "default ${board_type}\0" \
- "get_env=mw ${loadaddr} 0 0x20000;" \
- "mmc rescan;" \
- "ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} env.txt;" \
- "env import -t ${loadaddr}\0" \
- "default_env=mw ${loadaddr} 0 0x20000;" \
- "env export -t ${loadaddr} serial# ethaddr eth1addr " \
- "board_type panel;" \
- "env default -a;" \
- "env import -t ${loadaddr}\0" \
- "loadbootscript=" \
- "ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source\0" \
- "mmcpart=1\0" \
- "mmcdev=0\0" \
- "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
- "mmcargs=setenv bootargs console=${console},${baudrate} " \
- "root=${mmcroot}\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs addmtd addmisc set_fit_default;" \
- "bootm ${fit_addr_r}\0" \
- "mmc_load_fit=ext2load mmc ${mmcdev}:${mmcpart} ${fit_addr_r} " \
- "${fit_file}\0" \
- "mmc_load_uboot=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
- "${uboot}\0" \
- "mmc_upd_uboot=mw.b ${loadaddr} 0xff ${uboot_sz};" \
- "setexpr cmp_buf ${loadaddr} + ${uboot_sz};" \
- "setexpr uboot_maxsize ${uboot_sz} - 400;" \
- "mw.b ${cmp_buf} 0x00 ${uboot_sz};" \
- "run mmc_load_uboot;sf probe;sf erase 0 ${uboot_sz};" \
- "sf write ${loadaddr} 400 ${filesize};" \
- "sf read ${cmp_buf} 400 ${uboot_sz};" \
- "cmp.b ${loadaddr} ${cmp_buf} ${uboot_maxsize}\0" \
- "ubiboot=echo Booting from ubi ...; " \
- "run ubiargs addmtd addmisc set_fit_default;" \
- "bootm ${fit_addr_r}\0" \
- "rescueargs=setenv bootargs console=${console},${baudrate} " \
- "root=/dev/ram rw\0 " \
- "rescueboot=echo Booting rescue system from NOR ...; " \
- "run rescueargs addmtd addmisc set_fit_default;" \
- "bootm ${fit_addr_r}\0" \
- "rescue_load_fit=sf probe;sf read ${fit_addr_r} ${rescue_sys_addr} " \
- "${rescue_sys_length}; imi ${fit_addr_r}\0" \
- CONFIG_EXTRA_ENV_BOARD_SETTINGS
-
-#define CONFIG_BOOTCOMMAND \
- "mmc dev ${mmcdev};" \
- "if mmc rescan; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run mmc_load_fit; then " \
- "run mmcboot; " \
- "else " \
- "if run ubifs_load_fit; then " \
- "run ubiboot; " \
- "else " \
- "if run rescue_load_fit; then " \
- "run rescueboot; " \
- "else " \
- "echo RESCUE SYSTEM BOOT " \
- "FAILURE;" \
- "fi; " \
- "fi; " \
- "fi; " \
- "fi; " \
- "else " \
- "if run ubifs_load_fit; then " \
- "run ubiboot; " \
- "else " \
- "if run rescue_load_fit; then " \
- "run rescueboot; " \
- "else " \
- "echo RESCUE SYSTEM BOOT FAILURE;" \
- "fi; " \
- "fi; " \
- "fi"
-
-#define CONFIG_ARP_TIMEOUT 200UL
-
-#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x100000)
-#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
-
-/* Physical Memory Map */
-#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/* Environment organization */
-
-#define CONFIG_SYS_FSL_USDHC_NUM 2
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0x7f
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x00} }
-
-/* NAND stuff */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x40000000
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* DMA stuff, needed for GPMI/MXS NAND support */
-
-/* RTC */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_SYS_RTC_BUS_NUM 2
-#define CONFIG_RTC_M41T11
-
-/* USB Configs */
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
-#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS 0
-
-/* UBI support */
-
-/* Framebuffer */
-/* check this console not needed, after test remove it */
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_BMP_16BPP
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_IMX_VIDEO_SKIP
-
-#define CONFIG_IMX6_PWM_PER_CLK 66000000
-
-#endif /* __ARISTAINETOS_COMMON_CONFIG_H */
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2015
- * (C) Copyright 2014
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * Based on:
- * Copyright (C) 2012 Freescale Semiconductor, Inc.
- *
- * Configuration settings for the Freescale i.MX6Q SabreSD board.
- */
-#ifndef __ARISTAINETOS_CONFIG_H
-#define __ARISTAINETOS_CONFIG_H
-
-#define CONFIG_SYS_BOARD_VERSION 1
-#define CONFIG_HOSTNAME "aristainetos"
-#define CONFIG_BOARDNAME "aristainetos"
-
-#define CONFIG_MXC_UART_BASE UART5_BASE
-#define CONSOLE_DEV "ttymxc4"
-
-#define CONFIG_FEC_XCV_TYPE RMII
-
-#define CONFIG_EXTRA_ENV_BOARD_SETTINGS \
- "board_type=aristainetos7@1\0" \
- "mtdids=nand0=gpmi-nand,nor0=spi3.0\0" \
- "mtdparts=mtdparts=spi3.0:832k(u-boot),64k(env),64k(env-red)," \
- "-(rescue-system);gpmi-nand:-(ubi)\0" \
- "addmisc=setenv bootargs ${bootargs} consoleblank=0\0" \
- "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "ubiargs=setenv bootargs console=${console},${baudrate} " \
- "ubi.mtd=0,2048 root=ubi0:rootfs rootfstype=ubifs\0 " \
- "ubifs_load_fit=sf probe;ubi part ubi 2048;ubifsmount ubi:rootfs;" \
- "ubifsload ${fit_addr_r} /boot/system.itb; " \
- "imi ${fit_addr_r}\0 "
-
-#define ARISTAINETOS_USB_OTG_PWR IMX_GPIO_NR(4, 15)
-#define ARISTAINETOS_USB_H1_PWR IMX_GPIO_NR(3, 31)
-#define CONFIG_GPIO_ENABLE_SPI_FLASH IMX_GPIO_NR(2, 15)
-
-#include "aristainetos-common.h"
-
-#endif /* __ARISTAINETOS_CONFIG_H */
#ifndef __ARISTAINETOS2_CONFIG_H
#define __ARISTAINETOS2_CONFIG_H
-#define CONFIG_SYS_BOARD_VERSION 2
#define CONFIG_HOSTNAME "aristainetos2"
-#define CONFIG_BOARDNAME "aristainetos2"
#define CONFIG_MXC_UART_BASE UART2_BASE
#define CONSOLE_DEV "ttymxc1"
#define CONFIG_FEC_XCV_TYPE RGMII
+/* Framebuffer */
+#define CONFIG_SYS_LDB_CLOCK 28341000
+#define CONFIG_LG4573
+
+#include "mx6_common.h"
+
+#define CONFIG_MACH_TYPE 4501
+#define CONFIG_MMCROOT "/dev/mmcblk0p1"
+
+/* MMC Configs */
+#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC1_BASE_ADDR
+
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_ETHPRIME "FEC"
+#define CONFIG_FEC_MXC_PHYADDR 0
+
+#define CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
+
+#ifdef CONFIG_IMX_HAB
+#define HAB_EXTRA_SETTINGS \
+ "hab_check_addr=" \
+ "if hab_auth_img ${check_addr} ${filesize} ; then " \
+ "true;" \
+ "else " \
+ "echo \"HAB checks ${hab_check_filetype} " \
+ "failed!\"; " \
+ "false; " \
+ "fi;\0" \
+ "hab_check_file_fit=" \
+ "if env exists enable_hab_check && test " \
+ "${enable_hab_check} -eq 1 ; then " \
+ "setenv hab_check_filetype \"FIT file on SD card " \
+ "or eMMC\";" \
+ "env set check_addr ${fit_addr_r};" \
+ "run hab_check_addr;" \
+ "else " \
+ "true; "\
+ "fi;\0" \
+ "hab_check_file_bootscript=" \
+ "if env exists enable_hab_check && test " \
+ "${enable_hab_check} -eq 1 ; then " \
+ "setenv hab_check_filetype \"Bootscript file\";" \
+ "env set check_addr ${loadaddr};" \
+ "run hab_check_addr;" \
+ "else " \
+ "true; "\
+ "fi;\0" \
+ "hab_check_flash_fit=" \
+ "if env exists enable_hab_check && test " \
+ "${enable_hab_check} -eq 1 ; then " \
+ "setenv hab_check_filetype \"FIT files on flash\";" \
+ "env set check_addr ${fit_addr_r};" \
+ "run hab_check_addr;" \
+ "else " \
+ "true; "\
+ "fi;\0" \
+ "enable_hab_check=1\0"
+#else
+#define HAB_EXTRA_SETTINGS \
+ "hab_check_file_fit=echo HAB check FIT file always returns " \
+ "true;true\0" \
+ "hab_check_flash_fit=echo HAB check flash FIT always returns " \
+ "true;true\0" \
+ "hab_check_file_bootscript=echo HAB check bootscript always " \
+ "returns true;true\0" \
+ "enable_hab_check=0\0"
+#endif
+
+#if (CONFIG_SYS_BOARD_VERSION == 3)
#define CONFIG_EXTRA_ENV_BOARD_SETTINGS \
- "board_type=aristainetos2_7@1\0" \
- "nor_bootdelay=-2\0" \
+ "dead=led led_red on\0" \
+ "mtdids=nand0=gpmi-nand,nor0=spi0.0\0" \
+ "mtdparts=mtdparts=spi0.0:832k(u-boot),64k(env),64k(env-red)," \
+ "-(ubi-nor);gpmi-nand:-(ubi)\0" \
+ "addmisc=setenv bootargs ${bootargs} net.ifnames=0 consoleblank=0 " \
+ "bootmode=${bootmode} mmcpart=${mmcpart}\0" \
+ "mainboot=echo Booting from SD-card ...; " \
+ "run mainargs addmtd addmisc;" \
+ "if test -n ${addmiscM}; then run addmiscM;fi;" \
+ "if test -n ${addmiscC}; then run addmiscC;fi;" \
+ "if test -n ${addmiscD}; then run addmiscD;fi;" \
+ "run boot_board_type;" \
+ "bootm ${fit_addr_r}\0" \
+ "mainargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "main_load_fit=ext4load mmc ${mmcdev}:${mmcpart} ${fit_addr_r} " \
+ "${fit_file}\0" \
+ "rescue_load_fit=ext4load mmc ${mmcdev}:${mmcrescuepart} " \
+ "${fit_addr_r} ${rescue_fit_file}\0"
+#elif (CONFIG_SYS_BOARD_VERSION == 4)
+#define CONFIG_EXTRA_ENV_BOARD_SETTINGS \
+ "dead=led led_red on;led led_red2 on;\0" \
+ "mtdids=nand0=gpmi-nand,nor0=spi0.0\0" \
+ "mtdparts=mtdparts=spi0.0:832k(u-boot),64k(env),64k(env-red)," \
+ "-(ubi-nor);gpmi-nand:-(ubi)\0" \
+ "addmisc=setenv bootargs ${bootargs} net.ifnames=0 consoleblank=0 " \
+ "bootmode=${bootmode} mmcpart=${mmcpart}\0" \
+ "mainboot=echo Booting from SD-card ...; " \
+ "run mainargs addmtd addmisc;" \
+ "if test -n ${addmiscM}; then run addmiscM;fi;" \
+ "if test -n ${addmiscC}; then run addmiscC;fi;" \
+ "if test -n ${addmiscD}; then run addmiscD;fi;" \
+ "run boot_board_type;" \
+ "bootm ${fit_addr_r}\0" \
+ "mainargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "main_load_fit=ext4load mmc ${mmcdev}:${mmcpart} ${fit_addr_r} " \
+ "${fit_file}\0" \
+ "rescue_load_fit=ext4load mmc ${mmcdev}:${mmcrescuepart} " \
+ "${fit_addr_r} ${rescue_fit_file}\0"
+#elif (CONFIG_SYS_BOARD_VERSION == 5)
+#define CONFIG_EXTRA_ENV_BOARD_SETTINGS \
+ "emmcpart=1\0" \
+ "emmc_rescue_part=3\0" \
+ "emmcdev=1\0" \
+ "emmcroot=/dev/mmcblk1p1 rootwait rw\0" \
+ "dead=led led_red on\0" \
+ "mtdids=nor0=spi0.0\0" \
+ "mtdparts=mtdparts=spi0.0:832k(u-boot),64k(env),64k(env-red)," \
+ "-(ubi-nor)\0" \
+ "addmisc=setenv bootargs ${bootargs} net.ifnames=0 consoleblank=0 " \
+ "bootmode=${bootmode} mmcpart=${mmcpart} " \
+ "emmcpart=${emmcpart}\0" \
+ "mainboot=echo Booting from eMMC ...; " \
+ "run mainargs addmtd addmisc;" \
+ "if test -n ${addmiscM}; then run addmiscM;fi;" \
+ "if test -n ${addmiscC}; then run addmiscC;fi;" \
+ "if test -n ${addmiscD}; then run addmiscD;fi;" \
+ "run boot_board_type;" \
+ "bootm ${fit_addr_r}\0" \
+ "mainargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${emmcroot} rootfstype=ext4\0 " \
+ "main_load_fit=ext4load mmc ${emmcdev}:${emmcpart} ${fit_addr_r} " \
+ "${fit_file}; " \
+ "imi ${fit_addr_r}\0 " \
+ "rescue_load_fit=ext4load mmc ${emmcdev}:${emmc_rescue_part} " \
+ "${fit_addr_r} ${rescue_fit_file};imi ${fit_addr_r}\0"
+#else
+#define CONFIG_EXTRA_ENV_BOARD_SETTINGS \
+ "dead=led led_red on\0" \
"mtdids=nand0=gpmi-nand,nor0=spi3.1\0" \
"mtdparts=mtdparts=spi3.1:832k(u-boot),64k(env),64k(env-red)," \
- "-(rescue-system);gpmi-nand:-(ubi)\0" \
- "addmisc=setenv bootargs ${bootargs} net.ifnames=0 consoleblank=0\0" \
- "ubiargs=setenv bootargs console=${console},${baudrate} " \
- "ubi.mtd=0,4096 root=ubi0:rootfs rootfstype=ubifs\0 " \
- "ubifs_load_fit=sf probe;ubi part ubi 4096;ubifsmount ubi:rootfs;" \
- "ubifsload ${fit_addr_r} /boot/system.itb; " \
- "imi ${fit_addr_r}\0 "
+ "-(ubi-nor);gpmi-nand:-(ubi)\0" \
+ "addmisc=setenv bootargs ${bootargs} net.ifnames=0 consoleblank=0 " \
+ "bootmode=${bootmode} mmcpart=${mmcpart}\0" \
+ "mainboot=echo Booting from SD-card ...; " \
+ "run mainargs addmtd addmisc;" \
+ "if test -n ${addmiscM}; then run addmiscM;fi;" \
+ "if test -n ${addmiscC}; then run addmiscC;fi;" \
+ "if test -n ${addmiscD}; then run addmiscD;fi;" \
+ "run boot_board_type;" \
+ "bootm ${fit_addr_r}\0" \
+ "mainargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "main_load_fit=ext4load mmc ${mmcdev}:${mmcpart} ${fit_addr_r} " \
+ "${fit_file}\0" \
+ "rescue_load_fit=ext4load mmc ${mmcdev}:${mmcrescuepart} " \
+ "${fit_addr_r} ${rescue_fit_file}\0"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "disable_giga=yes\0" \
+ "usb_pgood_delay=2000\0" \
+ "nor_bootdelay=-2\0" \
+ "script=u-boot.scr\0" \
+ "fit_file=/boot/system.itb\0" \
+ "rescue_fit_file=/boot/rescue.itb\0" \
+ "loadaddr=0x12000000\0" \
+ "fit_addr_r=0x14000000\0" \
+ "uboot=/boot/u-boot.imx\0" \
+ "uboot_sz=d0000\0" \
+ "panel=lb07wv8\0" \
+ "splashpos=m,m\0" \
+ "console=" CONSOLE_DEV "\0" \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "boot_board_type=bootm ${fit_addr_r}#${board_type}\0" \
+ "get_env=mw ${loadaddr} 0 0x20000;" \
+ "mmc rescan;" \
+ "ext4load mmc ${mmcdev}:${mmcpart} ${loadaddr} env.txt;" \
+ "env import -t ${loadaddr}\0" \
+ "default_env=gpio set wp_spi_nor.gpio-hog;" \
+ "sf probe;" \
+ "sf protect unlock 0 0x1000000;" \
+ "mw ${loadaddr} 0 0x20000;" \
+ "env export -t ${loadaddr} serial# ethaddr " \
+ "board_type panel addmisc addmiscM addmiscC addmiscD;" \
+ "env default -a;" \
+ "env import -t ${loadaddr}\0" \
+ "loadbootscript=" \
+ "ext4load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
+ "${script};\0" \
+ "loadbootscriptUSB=" \
+ "ext4load usb 0 ${loadaddr} ${script};\0" \
+ "loadbootscriptUSBf=" \
+ "fatload usb 0 ${loadaddr} ${script};\0" \
+ "bootscriptUSB=echo Running bootscript from usb-stick ...; " \
+ "source\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "mmcpart=1\0" \
+ "mmcrescuepart=3\0" \
+ "mmcdev=0\0" \
+ "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs addmtd addmisc;" \
+ "if test -n ${addmiscM}; then run addmiscM;fi;" \
+ "if test -n ${addmiscC}; then run addmiscC;fi;" \
+ "if test -n ${addmiscD}; then run addmiscD;fi;" \
+ "run boot_board_type;" \
+ "bootm ${fit_addr_r}\0" \
+ "mmc_load_fit=ext4load mmc ${mmcdev}:${mmcpart} ${fit_addr_r} " \
+ "${fit_file}\0" \
+ "mmc_load_uboot=ext4load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
+ "${uboot}\0" \
+ "mmc_rescue_load_fit=ext4load mmc ${mmcdev}:${mmcrescuepart} " \
+ "${fit_addr_r} ${rescue_fit_file}\0" \
+ "mmc_upd_uboot=mw.b ${loadaddr} 0xff ${uboot_sz};" \
+ "setexpr cmp_buf ${loadaddr} + ${uboot_sz};" \
+ "setexpr uboot_maxsize ${uboot_sz} - 400;" \
+ "mw.b ${cmp_buf} 0x00 ${uboot_sz};" \
+ "run mmc_load_uboot;sf probe;sf erase 0 ${uboot_sz};" \
+ "sf write ${loadaddr} 400 ${filesize};" \
+ "sf read ${cmp_buf} 400 ${uboot_sz};" \
+ "cmp.b ${loadaddr} ${cmp_buf} ${uboot_maxsize}\0" \
+ "rescueargs=setenv bootargs console=${console},${baudrate} " \
+ "root=/dev/ram rw\0 " \
+ "rescueboot=echo Booting rescue system ...; " \
+ "run rescueargs addmtd addmisc;" \
+ "if test -n ${rescue_reason}; then run rescue_reason;fi;" \
+ "if test -n ${addmiscM}; then run addmiscM;fi;" \
+ "if test -n ${addmiscC}; then run addmiscC;fi;" \
+ "if test -n ${addmiscD}; then run addmiscD;fi;" \
+ "run boot_board_type;" \
+ "if bootm ${fit_addr_r}; then ; " \
+ "else " \
+ "run dead; " \
+ "fi; \0" \
+ "r_reason_syserr=setenv rescue_reason setenv bootargs " \
+ "\\\\${bootargs} " \
+ "rescueReason=18\0 " \
+ "usb_load_fit=ext4load usb 0 ${fit_addr_r} ${fit_file}\0" \
+ "usb_load_fitf=fatload usb 0 ${fit_addr_r} ${fit_file}\0" \
+ "usb_load_rescuefit=ext4load usb 0 ${fit_addr_r} " \
+ "${rescue_fit_file}\0" \
+ "usb_load_rescuefitf=fatload usb 0 ${fit_addr_r} " \
+ "${rescue_fit_file}\0" \
+ "usbroot=/dev/sda1 rootwait rw\0" \
+ "usbboot=echo Booting from usb-stick ...; " \
+ "run usbargs addmtd addmisc;" \
+ "if test -n ${addmiscM}; then run addmiscM;fi;" \
+ "if test -n ${addmiscC}; then run addmiscC;fi;" \
+ "if test -n ${addmiscD}; then run addmiscD;fi;" \
+ "run boot_board_type;" \
+ "bootm ${fit_addr_r}\0" \
+ "usbargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${usbroot}\0" \
+ "mmc_rescue_boot=" \
+ "run r_reason_syserr;" \
+ "if run mmc_rescue_load_fit hab_check_file_fit; then " \
+ "run rescueboot; " \
+ "else " \
+ "run dead; " \
+ "echo RESCUE SYSTEM FROM SD-CARD BOOT FAILURE;" \
+ "fi;\0" \
+ "main_rescue_boot=" \
+ "if run main_load_fit hab_check_flash_fit; then " \
+ "if run mainboot; then ; " \
+ "else " \
+ "run r_reason_syserr;" \
+ "if run rescue_load_fit hab_check_file_fit;" \
+ "then run rescueboot; " \
+ "else " \
+ "run dead; " \
+ "echo RESCUE SYSTEM BOOT FAILURE;" \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "run r_reason_syserr;" \
+ "if run rescue_load_fit hab_check_file_fit; then " \
+ "run rescueboot; " \
+ "else " \
+ "run dead; " \
+ "echo RESCUE SYSTEM BOOT FAILURE;" \
+ "fi; " \
+ "fi;\0" \
+ "usb_mmc_rescue_boot=" \
+ "usb start;" \
+ "if usb storage; then " \
+ "if run loadbootscriptUSB " \
+ "hab_check_file_bootscript;" \
+ "then run bootscriptUSB; " \
+ "fi; " \
+ "if run loadbootscriptUSBf " \
+ "hab_check_file_bootscript;" \
+ "then run bootscriptUSB; " \
+ "fi; " \
+ "if run usb_load_fit hab_check_file_fit; then " \
+ "run usbboot; " \
+ "fi; " \
+ "if run usb_load_fitf hab_check_file_fit; then " \
+ "run usbboot; " \
+ "fi; "\
+ "if run usb_load_rescuefit hab_check_file_fit;" \
+ "then run r_reason_syserr rescueboot;" \
+ "fi; " \
+ "if run usb_load_rescuefitf hab_check_file_fit;" \
+ "then run r_reason_syserr rescueboot;" \
+ "fi; " \
+ "run mmc_rescue_boot;" \
+ "fi; "\
+ "run mmc_rescue_boot;\0" \
+ "rescue_xload_boot=" \
+ "run r_reason_syserr;" \
+ "if test ${bootmode} -ne 0 ; then " \
+ "mmc dev ${mmcdev};" \
+ "if mmc rescan; then " \
+ "if run mmc_rescue_load_fit " \
+ "hab_check_file_fit; then " \
+ "run rescueboot; " \
+ "else " \
+ "usb start;" \
+ "if usb storage; then " \
+ "if run usb_load_rescuefit " \
+ "hab_check_file_fit;"\
+ "then " \
+ "run rescueboot;" \
+ "fi; " \
+ "if run usb_load_rescuefitf "\
+ "hab_check_file_fit;"\
+ "then " \
+ "run rescueboot;" \
+ "fi; " \
+ "fi;" \
+ "fi;" \
+ "run dead; " \
+ "echo RESCUE SYSTEM ON SD OR " \
+ "USB BOOT FAILURE;" \
+ "else " \
+ "usb start;" \
+ "if usb storage; then " \
+ "if run usb_load_rescuefit " \
+ "hab_check_file_fit; then " \
+ "run rescueboot;" \
+ "fi; " \
+ "if run usb_load_rescuefitf " \
+ "hab_check_file_fit; then " \
+ "run rescueboot;" \
+ "fi; " \
+ "fi;" \
+ "run dead; " \
+ "echo RESCUE SYSTEM ON USB BOOT FAILURE;" \
+ "fi; " \
+ "else "\
+ "if run rescue_load_fit hab_check_file_fit; then " \
+ "run rescueboot; " \
+ "else " \
+ "run dead; " \
+ "echo RESCUE SYSTEM ON BOARD BOOT FAILURE;" \
+ "fi; " \
+ "fi;\0" \
+ "ari_boot=if test ${bootmode} -ne 0 ; then " \
+ "mmc dev ${mmcdev};" \
+ "if mmc rescan; then " \
+ "if run loadbootscript hab_check_file_bootscript;" \
+ "then run bootscript; " \
+ "fi; " \
+ "if run mmc_load_fit hab_check_file_fit; then " \
+ "if run mmcboot; then ; " \
+ "else " \
+ "run mmc_rescue_boot;" \
+ "fi; " \
+ "else " \
+ "run usb_mmc_rescue_boot;" \
+ "fi; " \
+ "else " \
+ "run usb_mmc_rescue_boot;" \
+ "fi; " \
+ "else "\
+ "run main_rescue_boot;" \
+ "fi; \0"\
+ HAB_EXTRA_SETTINGS \
+ CONFIG_EXTRA_ENV_BOARD_SETTINGS
+
+#define CONFIG_ARP_TIMEOUT 200UL
+
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x100000)
+#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
+
+/* Physical Memory Map */
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
-#define CONFIG_SYS_I2C_MXC_I2C4 /* enable I2C bus 4 */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-#define ARISTAINETOS_USB_OTG_PWR IMX_GPIO_NR(4, 15)
-#define ARISTAINETOS_USB_H1_PWR IMX_GPIO_NR(1, 0)
-#define CONFIG_GPIO_ENABLE_SPI_FLASH IMX_GPIO_NR(2, 15)
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+
+/* NAND stuff */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x40000000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* DMA stuff, needed for GPMI/MXS NAND support */
+
+/* USB Configs */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+
+/* UBI support */
/* Framebuffer */
-#define CONFIG_SYS_LDB_CLOCK 33246000
-#define CONFIG_LG4573
-#define CONFIG_LG4573_BUS 0
-#define CONFIG_LG4573_CS 0
+/* check this console not needed, after test remove it */
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_IMX_VIDEO_SKIP
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_BMP_RLE8
-#include "aristainetos-common.h"
+#define CONFIG_IMX6_PWM_PER_CLK 66000000
#endif /* __ARISTAINETOS2_CONFIG_H */
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2015
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * Based on:
- * Copyright (C) 2012 Freescale Semiconductor, Inc.
- *
- * Configuration settings for the Freescale i.MX6DL aristainetos2 board.
- */
-#ifndef __ARISTAINETOS2B_CONFIG_H
-#define __ARISTAINETOS2B_CONFIG_H
-
-#define CONFIG_SYS_BOARD_VERSION 3
-#define CONFIG_HOSTNAME "aristainetos2"
-#define CONFIG_BOARDNAME "aristainetos2-revB"
-
-#define CONFIG_MXC_UART_BASE UART2_BASE
-#define CONSOLE_DEV "ttymxc1"
-
-#define CONFIG_FEC_XCV_TYPE RGMII
-
-#define CONFIG_EXTRA_ENV_BOARD_SETTINGS \
- "board_type=aristainetos2_7@1\0" \
- "nor_bootdelay=-2\0" \
- "mtdids=nand0=gpmi-nand,nor0=spi0.0\0" \
- "mtdparts=mtdparts=spi0.0:832k(u-boot),64k(env),64k(env-red)," \
- "-(rescue-system);gpmi-nand:-(ubi)\0" \
- "addmisc=setenv bootargs ${bootargs} net.ifnames=0 consoleblank=0\0" \
- "ubiargs=setenv bootargs console=${console},${baudrate} " \
- "ubi.mtd=0,4096 root=ubi0:rootfs rootfstype=ubifs\0 " \
- "ubifs_load_fit=sf probe;ubi part ubi 4096;ubifsmount ubi:rootfs;" \
- "ubifsload ${fit_addr_r} /boot/system.itb; " \
- "imi ${fit_addr_r}\0 " \
-
-#define CONFIG_SYS_I2C_MXC_I2C4 /* enable I2C bus 4 */
-
-#define ARISTAINETOS_USB_OTG_PWR IMX_GPIO_NR(4, 15)
-#define ARISTAINETOS_USB_H1_PWR IMX_GPIO_NR(1, 0)
-#define CONFIG_GPIO_ENABLE_SPI_FLASH IMX_GPIO_NR(2, 15)
-
-/* Framebuffer */
-#define CONFIG_SYS_LDB_CLOCK 33246000
-#define CONFIG_LG4573
-#define CONFIG_LG4573_BUS 0
-#define CONFIG_LG4573_CS 1
-
-#include "aristainetos-common.h"
-
-#endif /* __ARISTAINETOS2B_CONFIG_H */
/* APBH DMA is required for NAND support */
#endif
+/* SPI Flash Configs */
+#if defined(CONFIG_SPL_BUILD)
+#undef CONFIG_DM_SPI
+#undef CONFIG_DM_SPI_FLASH
+#undef CONFIG_SPI_FLASH_MTD
+#endif
+
/* Ethernet */
#define CONFIG_FEC_MXC
#define CONFIG_FEC_MXC_PHYADDR 0
"ramdisk_addr_r=0x82200000\0" \
"scriptaddr=0x87000000\0"
+#define UBOOT_UPDATE \
+ "update_uboot=nand erase.part u-boot1 && " \
+ "nand write ${loadaddr} u-boot1 ${filesize} && " \
+ "nand erase.part u-boot2 && " \
+ "nand write ${loadaddr} u-boot2 ${filesize}\0"
+
#define NFS_BOOTCMD \
"nfsargs=ip=:::::eth0: root=/dev/nfs\0" \
"nfsboot=run setup; " \
MEM_LAYOUT_ENV_SETTINGS \
NFS_BOOTCMD \
UBI_BOOTCMD \
+ UBOOT_UPDATE \
"console=ttymxc0\0" \
"defargs=user_debug=30\0" \
"dfu_alt_info=" DFU_ALT_NAND_INFO "\0" \
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_SYS_FSL_USDHC_NUM 2
-/* Network */
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_MXC_PHYADDR 1
-#define CONFIG_TFTP_TSIZE
-
/* USB Configs */
/* Host */
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
"imx6dl-colibri-eval-v3.dtb fat 0 1;" \
"imx6dl-colibri-cam-eval-v3.dtb fat 0 1"
+#define UBOOT_UPDATE \
+ "uboot_hwpart=1\0" \
+ "uboot_blk=8a\0" \
+ "uboot_spl_blk=2\0" \
+ "set_blkcnt=setexpr blkcnt ${filesize} + 0x1ff && " \
+ "setexpr blkcnt ${blkcnt} / 0x200\0" \
+ "update_uboot=run set_blkcnt && mmc dev 0 ${uboot_hwpart} && " \
+ "mmc write ${loadaddr} ${uboot_blk} ${blkcnt}\0" \
+ "update_spl=run set_blkcnt && mmc dev 0 ${uboot_hwpart} && " \
+ "mmc write ${loadaddr} ${uboot_spl_blk} ${blkcnt}\0"
+
#define EMMC_BOOTCMD \
"set_emmcargs=setenv emmcargs ip=off root=PARTUUID=${uuid} "\
"rw,noatime rootfstype=ext4 " \
"fdt_fixup=;\0" \
MEM_LAYOUT_ENV_SETTINGS \
NFS_BOOTCMD \
+ UBOOT_UPDATE \
"setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
"00:14:2d:00:00:00; fi; tftpboot ${loadaddr} " \
"flash_eth.img && source ${loadaddr}\0" \
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)
-/* Network */
-#define CONFIG_FEC_MXC
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_MXC_PHYADDR 0
-
-#define CONFIG_TFTP_TSIZE
-
-/* ENET1 */
-#define IMX_FEC_BASE ENET_IPS_BASE_ADDR
-
/* MMC Config*/
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#ifdef CONFIG_TARGET_COLIBRI_IMX7_NAND
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_SERVERIP 192.168.10.1
+#if defined(CONFIG_TARGET_COLIBRI_IMX7_EMMC)
+#define UBOOT_UPDATE \
+ "uboot_hwpart=1\0" \
+ "uboot_blk=2\0" \
+ "set_blkcnt=setexpr blkcnt ${filesize} + 0x1ff && " \
+ "setexpr blkcnt ${blkcnt} / 0x200\0" \
+ "update_uboot=run set_blkcnt && mmc dev 0 ${uboot_hwpart} && " \
+ "mmc write ${loadaddr} ${uboot_blk} ${blkcnt}\0"
+#elif defined(CONFIG_TARGET_COLIBRI_IMX7_NAND)
+#define UBOOT_UPDATE \
+ "update_uboot=nand erase.part u-boot1 && " \
+ "nand write ${loadaddr} u-boot1 ${filesize} && " \
+ "nand erase.part u-boot2 && " \
+ "nand write ${loadaddr} u-boot2 ${filesize}\0"
+#endif
+
#ifndef PARTS_DEFAULT
/* Define the default GPT table for eMMC */
#define PARTS_DEFAULT \
MEM_LAYOUT_ENV_SETTINGS \
NFS_BOOTCMD \
MODULE_EXTRA_ENV_SETTINGS \
+ UBOOT_UPDATE \
"boot_file=zImage\0" \
"console=ttymxc0\0" \
"defargs=\0" \
"ramdisk_addr_r=0x82100000\0" \
"scriptaddr=0x87000000\0"
+#define UBOOT_UPDATE \
+ "update_uboot=nand erase.part u-boot && " \
+ "nand write ${loadaddr} u-boot ${filesize}\0" \
+
#define NFS_BOOTCMD \
"nfsargs=ip=:::::eth0: root=/dev/nfs\0" \
"nfsboot=run setup; " \
NFS_BOOTCMD \
SD_BOOTCMD \
UBI_BOOTCMD \
+ UBOOT_UPDATE \
"console=ttyLP0\0" \
"defargs=user_debug=30\0" \
"dfu_alt_info=" DFU_ALT_NAND_INFO "\0" \
#endif
/* Watchdog */
+#if defined(CONFIG_SPL_BUILD)
+#undef CONFIG_WDT
+#undef CONFIG_WATCHDOG
+#define CONFIG_HW_WATCHDOG
+#endif
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_USB_GADGET_MASS_STORAGE
#endif
-/* Networking Configs */
-#ifdef CONFIG_NET
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_MXC_PHYADDR 4
-#define CONFIG_PHY_ATHEROS
-#endif
-
/* Serial Flash */
/* allow to overwrite serial and ethaddr */
"setargs=setenv bootargs root=/dev/${rootdev}${partnum} " \
"ro rootwait cma=128M " \
"bootcause=${bootcause} " \
- "${quiet} console=${console} ${rtc_status} " \
+ "${quiet} console=${console} " \
"${videoargs}" "\0" \
"doquiet=" \
"if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \
"swappartitions=" \
"setexpr partnum 3 - ${partnum}\0" \
"failbootcmd=" \
+ "echo reached failbootcmd; " \
"bx50_backlight_enable; " \
- "msg=\"Monitor failed to start. Try again, or contact GE Service for support.\"; " \
- "echo $msg; " \
- "setenv stdout vga; " \
- "echo \"\n\n\n\n \" $msg; " \
- "setenv stdout serial; " \
+ "setcurs 5 4; " \
+ "lcdputs \"Monitor failed to start. " \
+ "Try again, or contact GE Service for support.\"; " \
"mw.b 0x7000A000 0xbc; " \
"mw.b 0x7000A001 0x00; " \
"ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \
#define CONFIG_IMX6_PWM_PER_CLK 66000000
-#define CONFIG_PCI
-#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_PCIE_IMX
#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12)
/* MTD device */
#endif
-/* Ethernet */
-#ifdef CONFIG_FEC_MXC
-# ifdef CONFIG_TARGET_MX6Q_ICORE_RQS
-# define CONFIG_FEC_MXC_PHYADDR 3
-# define CONFIG_FEC_XCV_TYPE RGMII
-# else
-# define CONFIG_FEC_MXC_PHYADDR 0
-# define CONFIG_FEC_XCV_TYPE RMII
-# endif
-#endif
-
/* Falcon Mode */
#ifdef CONFIG_SPL_OS_BOOT
# define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
- "image=Image.itb\0" \
+ "image=Image\0" \
"console=ttymxc1,115200\0" \
"fdt_addr=0x43000000\0" \
"fdt_high=0xffffffffffffffff\0" \
- "boot_fit=try\0" \
- "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
+ "boot_fit=no\0" \
+ "fdt_file=imx8mm-evk.dtb\0" \
"initrd_addr=0x43800000\0" \
"initrd_high=0xffffffffffffffff\0" \
"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SYS_MMC_ENV_DEV 0 /* USDHC2 */
+#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */
#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2 */
/* Size of malloc() pool */
#define CONFIG_SYS_FSL_CLK
/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (32 * 1024 * 1024)
#define CONFIG_REVISION_TAG
/* bootz: zImage/initrd.img support */
-/* Eth Configs */
-#define IMX_FEC_BASE FEC_BASE_ADDR
-#define CONFIG_ETHPRIME "FEC0"
-#define CONFIG_FEC_MXC_PHYADDR 0x1F
/* USB Configs */
#define CONFIG_MXC_USB_PORT 1
#define CONFIG_LOADADDR 0x70010000 /* loadaddr env var */
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(MMC, mmc, 1) \
+ func(USB, usb, 0) \
+ func(PXE, pxe, na)
+
+#include <config_distro_bootcmd.h>
+
#define CONFIG_EXTRA_ENV_SETTINGS \
- "fdt_addr_r=0x71ff0000\0" \
+ "fdt_addr_r=0x75000000\0" \
"pxefile_addr_r=0x73000000\0" \
- "ramdisk_addr_r=0x72000000\0" \
+ "scriptaddr=0x74000000\0" \
+ "ramdisk_addr_r=0x80000000\0" \
+ "kernel_addr_r=0x72000000\0" \
+ "fdt_high=0xffffffff\0" \
"console=ttymxc1,115200\0" \
- "uenv=/boot/uEnv.txt\0" \
- "optargs=\0" \
- "cmdline=\0" \
- "mmcdev=0\0" \
- "mmcpart=1\0" \
- "mmcrootfstype=ext4 rootwait fixrtc\0" \
- "mmcargs=setenv bootargs console=${console} " \
- "${optargs} " \
- "root=/dev/mmcblk${mmcdev}p${mmcpart} ro " \
- "rootfstype=${mmcrootfstype} " \
- "${cmdline}\0" \
- "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
- "loadpxe=dhcp;setenv kernel_addr_r ${loadaddr};pxe get;pxe boot;\0" \
- "loadrd=load mmc ${bootpart} ${ramdisk_addr_r} ${bootdir}/${rdfile};" \
- "setenv rdsize ${filesize}\0" \
- "loadfdt=echo loading ${fdt_path} ...;" \
- "load mmc ${bootpart} ${fdt_addr_r} ${fdt_path}\0" \
- "mmcboot=mmc dev ${mmcdev}; " \
- "if mmc rescan; then " \
- "echo SD/MMC found on device ${mmcdev};" \
- "echo Checking for: ${uenv} ...;" \
- "setenv bootpart ${mmcdev}:${mmcpart};" \
- "if test -e mmc ${bootpart} ${uenv}; then " \
- "load mmc ${bootpart} ${loadaddr} ${uenv};" \
- "env import -t ${loadaddr} ${filesize};" \
- "echo Loaded environment from ${uenv};" \
- "if test -n ${dtb}; then " \
- "setenv fdt_file ${dtb};" \
- "echo Using: dtb=${fdt_file} ...;" \
- "fi;" \
- "echo Checking for uname_r in ${uenv}...;" \
- "if test -n ${uname_r}; then " \
- "echo Running uname_boot ...;" \
- "run uname_boot;" \
- "fi;" \
- "fi;" \
- "fi;\0" \
- "uname_boot="\
- "setenv bootdir /boot; " \
- "setenv bootfile vmlinuz-${uname_r}; " \
- "setenv ccatfile /boot/ccat.rbf; " \
- "echo loading CCAT firmware from ${ccatfile}; " \
- "load mmc ${bootpart} ${loadaddr} ${ccatfile}; " \
- "fpga load 0 ${loadaddr} ${filesize}; " \
- "if test -e mmc ${bootpart} ${bootdir}/${bootfile}; then " \
- "echo loading ${bootdir}/${bootfile} ...; " \
- "run loadimage;" \
- "setenv fdt_path /boot/dtbs/${uname_r}/${fdt_file}; " \
- "if test -e mmc ${bootpart} ${fdt_path}; then " \
- "run loadfdt;" \
- "else " \
- "echo; echo unable to find ${fdt_file} ...;" \
- "echo booting legacy ...;"\
- "run mmcargs;" \
- "echo debug: [${bootargs}] ... ;" \
- "echo debug: [bootz ${loadaddr}] ... ;" \
- "bootz ${loadaddr}; " \
- "fi;" \
- "run mmcargs;" \
- "echo debug: [${bootargs}] ... ;" \
- "echo debug: [bootz ${loadaddr} - ${fdt_addr_r}];" \
- "bootz ${loadaddr} - ${fdt_addr_r}; " \
- "else " \
- "echo loading from dhcp ...; " \
- "run loadpxe; " \
- "fi;\0"
-
-#define CONFIG_BOOTCOMMAND \
- "run mmcboot;"
+ "stdin=serial\0" \
+ "stdout=serial,vidconsole\0" \
+ "stderr=serial,vidconsole\0" \
+ "fdtfile=imx53-cx9020.dtb\0" \
+ BOOTENV
#define CONFIG_ARP_TIMEOUT 200UL
"lvds=ldb\0" \
"setargs=setenv bootargs ${lvds} jtag=on mem=2G " \
"vt.global_cursor_default=0 bootcause=${bootcause} ${quiet} " \
- "console=${console} ${rtc_status}\0" \
+ "console=${console}\0" \
"bootargs_emmc=setenv bootargs root=/dev/${rootdev}${partnum} ro " \
"rootwait ${bootargs}\0" \
"doquiet=if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \
#define CONFIG_IMX_VIDEO_SKIP
/* USB */
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS 0
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
/* Command definition */
BOOTENV
#define BOOT_TARGET_DEVICES(func) \
- func(MMC, mmc, 0) \
+ func(MMC, mmc, 1) \
+ func(MMC, mmc, 2) \
func(SATA, sata, 0) \
func(USB, usb, 0) \
func(PXE, pxe, na) \
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)
-/* Network */
-#define CONFIG_FEC_MXC
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_MXC_PHYADDR 0
-
-#define CONFIG_PHY_BROADCOM
-/* ENET1 */
-#define IMX_FEC_BASE ENET_IPS_BASE_ADDR
-
/* MMC Config*/
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
"image=zImage\0" \
"console=ttymxc0\0" \
"fdt_high=0xffffffff\0" \
+ "finduuid=part uuid mmc 0:1 uuid\0" \
"initrd_high=0xffffffff\0" \
- "fdt_file=imx7d-sdb.dtb\0" \
+ "fdtfile=imx7d-sdb.dtb\0" \
"fdt_addr=0x83000000\0" \
- "boot_fdt=try\0" \
- "ip_dyn=yes\0" \
+ "fdt_addr_r=0x83000000\0" \
+ "kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
+ "pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
+ "ramdisk_addr_r=0x83000000\0" \
+ "ramdiskaddr=0x83000000\0" \
+ "scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
"videomode=video=ctfb:x:480,y:272,depth:24,pclk:108695,le:8,ri:4,up:2,lo:4,hs:41,vs:10,sync:0,vmode:0\0" \
- "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
- "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
- "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
- "mmcautodetect=yes\0" \
- "mmcargs=setenv bootargs console=${console},${baudrate} " \
- "root=${mmcroot}\0" \
- "loadbootscript=" \
- "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source\0" \
- "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
- "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if run loadfdt; then " \
- "bootz ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootz; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootz; " \
- "fi;\0" \
- "netargs=setenv bootargs console=${console},${baudrate} " \
- "root=/dev/nfs " \
- "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
- "netboot=echo Booting from net ...; " \
- "run netargs; " \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "${get_cmd} ${image}; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootz ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootz; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootz; " \
- "fi;\0"
-
-#define CONFIG_BOOTCOMMAND \
- "mmc dev ${mmcdev};" \
- "mmc dev ${mmcdev}; if mmc rescan; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loadimage; then " \
- "run mmcboot; " \
- "else run netboot; " \
- "fi; " \
- "fi; " \
- "else run netboot; fi"
+ BOOTENV
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(DHCP, dhcp, na) \
+ func(PXE, pxe, na)
+
+#include <config_distro_bootcmd.h>
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x20000000)
#define CONFIG_SYS_MMC_ENV_DEV 0 /* USDHC1 */
#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */
-#define CONFIG_MMCROOT "/dev/mmcblk0p2" /* USDHC1 */
/* USB Configs */
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Embedded Artists i.MX7ULP COM board.
+ */
+
+#ifndef __MX7ULP_COM_CONFIG_H
+#define __MX7ULP_COM_CONFIG_H
+
+#include <linux/sizes.h>
+#include <asm/arch/imx-regs.h>
+
+#define CONFIG_BOARD_POSTCLK_INIT
+#define CONFIG_SYS_BOOTM_LEN 0x1000000
+
+#define SRC_BASE_ADDR CMC1_RBASE
+#define IRAM_BASE_ADDR OCRAM_0_BASE
+#define IOMUXC_BASE_ADDR IOMUXC1_RBASE
+
+/*
+ * Detect overlap between U-Boot image and environment area in build-time
+ *
+ * CONFIG_BOARD_SIZE_LIMIT = CONFIG_ENV_OFFSET - u-boot-dtb.imx offset
+ * CONFIG_BOARD_SIZE_LIMIT = 768k - 1k = 767k = 785408
+ *
+ * Currently CONFIG_BOARD_SIZE_LIMIT does not handle expressions, so
+ * write the direct value here
+ */
+#define CONFIG_BOARD_SIZE_LIMIT 785408
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_MMCROOT "/dev/mmcblk0p2"
+#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
+
+/* Using ULP WDOG for reset */
+#define WDOG_BASE_ADDR WDG1_RBASE
+
+#define CONFIG_SYS_HZ_CLOCK 1000000 /* Fixed at 1MHz from TSTMR */
+
+#define CONFIG_INITRD_TAG
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (8 * SZ_1M)
+
+/* UART */
+#define LPUART_BASE LPUART4_RBASE
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Physical Memory Map */
+
+#define PHYS_SDRAM 0x60000000
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+
+#define CONFIG_LOADADDR 0x60800000
+
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + SZ_512M)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "image=zImage\0" \
+ "console=ttyLP0\0" \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "fdt_file=imx7ulp-com.dtb\0" \
+ "fdt_addr=0x63000000\0" \
+ "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+ "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+ "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if run loadfdt; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "fi;\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ "if run loadimage; then " \
+ "run mmcboot; " \
+ "fi; " \
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE SZ_256K
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+#if !CONFIG_IS_ENABLED(SYS_DCACHE_OFF)
+#define CONFIG_CMD_CACHE
+#endif
+
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#endif /* __CONFIG_H */
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2019 DENX Software Engineering
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ *
+ * Copyright (C) 2018 DENX Software Engineering
+ * Måns Rullgård, DENX Software Engineering, mans@mansr.com
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ */
+#ifndef __CONFIGS_XEA_H__
+#define __CONFIGS_XEA_H__
+
+#include <linux/sizes.h>
+
+#define CONFIG_TIMESTAMP /* Print image info with timestamp */
+
+/* SPL */
+#define CONFIG_SPL_STACK 0x20000
+
+#define CONFIG_SYS_SPL_ARGS_ADDR 0x44000000
+
+#define CONFIG_SYS_SPI_KERNEL_OFFS SZ_1M
+#define CONFIG_SYS_SPI_ARGS_OFFS SZ_512K
+#define CONFIG_SYS_SPI_ARGS_SIZE SZ_32K
+
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR (SZ_512K / 0x200)
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (SZ_32K / 0x200)
+#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR (SZ_1M / 0x200)
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SPI_FLASH_MTD
+#endif
+
+/* Memory configuration */
+#define PHYS_SDRAM_1 0x40000000 /* Base address */
+#define PHYS_SDRAM_1_SIZE 0x10000000 /* Max 256 MB RAM */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+
+/* Environment */
+#define CONFIG_ENV_OVERWRITE
+
+/* Booting Linux */
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_BOOTARGS "console=ttyAMA0,115200n8 "
+#define CONFIG_BOOTCOMMAND "run ${bootpri} ; run ${bootsec}"
+#define CONFIG_LOADADDR 0x42000000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+/* Extra Environment */
+#define CONFIG_PREBOOT "run prebootcmd"
+#define CONFIG_HOSTNAME "xea"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "bootmode=update\0" \
+ "bootpri=mmc_mmc\0" \
+ "bootsec=sf_swu\0" \
+ "consdev=ttyAMA0\0" \
+ "baudrate=115200\0" \
+ "dtbaddr=0x44000000\0" \
+ "dtbfile=imx28-xea.dtb\0" \
+ "rootdev=/dev/mmcblk0p2\0" \
+ "netdev=eth0\0" \
+ "rdaddr=0x43000000\0" \
+ "swufile=swupdate.img\0" \
+ "sf_kernel_offset=0x100000\0" \
+ "sf_kernel_size=0x400000\0" \
+ "sf_swu_offset=0x500000\0" \
+ "sf_swu_size=0x800000\0" \
+ "rootpath=/opt/eldk-5.5/armv5te/rootfs-qte-sdk\0" \
+ "do_update_mmc=" \
+ "if mmc rescan ; then " \
+ "mmc dev 0 ${update_mmc_part} ; " \
+ "if dhcp ${hostname}/${update_filename} ; then " \
+ "setexpr fw_sz ${filesize} / 0x200 ; " /* SD block size */ \
+ "setexpr fw_sz ${fw_sz} + 1 ; " \
+ "mmc write ${loadaddr} ${update_offset} ${fw_sz} ; " \
+ "fi ; " \
+ "fi\0" \
+ "do_update_sf=" \
+ "if sf probe ; then " \
+ "if dhcp ${hostname}/${update_filename} ; then " \
+ "sf erase ${update_offset} +${filesize} ; " \
+ "sf write ${loadaddr} ${update_offset} ${filesize} ; " \
+ "fi ; " \
+ "fi\0" \
+ "update_spl_filename=u-boot.sb\0" \
+ "update_spl=" \
+ "setenv update_filename ${update_spl_filename} ; " \
+ "setenv update_offset 0 ; " \
+ "run do_update_sf\0" \
+ "update_uboot_filename=u-boot.img\0" \
+ "update_uboot=" \
+ "setenv update_filename ${update_uboot_filename} ; " \
+ "setenv update_offset 0x10000 ; " \
+ "run do_update_sf ; " \
+ "setenv update_mmc_part 1 ; " \
+ "setenv update_offset 0 ; " \
+ "run do_update_mmc\0" \
+ "update_kernel_filename=uImage\0" \
+ "update_kernel=" \
+ "setenv update_mmc_part 1 ; " \
+ "setenv update_filename ${update_kernel_filename} ; " \
+ "setenv update_offset 0x800 ; " \
+ "run do_update_mmc ; " \
+ "setenv update_filename ${dtbfile} ; " \
+ "setenv update_offset 0x400 ; " \
+ "run do_update_mmc\0" \
+ "update_sfkernel=" \
+ "setenv update_filename fitImage ; " \
+ "setenv update_offset ${sf_kernel_offset} ; " \
+ "run do_update_sf\0" \
+ "update_swu=" \
+ "setenv update_filename ${swufile} ; " \
+ "setenv update_offset ${sf_swu_offset} ; " \
+ "run do_update_sf\0" \
+ "addcons=" \
+ "setenv bootargs ${bootargs} " \
+ "console=${consdev},${baudrate}\0" \
+ "addip=" \
+ "setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:" \
+ "${netmask}:${hostname}:${netdev}:off\0" \
+ "addmisc=" \
+ "setenv bootargs ${bootargs} ${miscargs}\0" \
+ "addargs=run addcons addmisc\0" \
+ "mmcload=" \
+ "mmc rescan ; " \
+ "mmc dev 0 1 ; " \
+ "mmc read ${loadaddr} 0x800 0x2000 ; " \
+ "mmc read ${dtbaddr} 0x400 0x80\0" \
+ "netload=" \
+ "dhcp ${loadaddr} ${hostname}/${bootfile} ; " \
+ "tftp ${dtbaddr} ${hostname}/${dtbfile}\0" \
+ "sfload=" \
+ "sf probe ; " \
+ "sf read ${loadaddr} ${sf_kernel_offset} ${sf_kernel_size}\0" \
+ "usbload=" \
+ "usb start ; " \
+ "load usb 0:1 ${loadaddr} ${bootfile}\0" \
+ "miscargs=panic=1\0" \
+ "mmcargs=setenv bootargs root=${rootdev} rw rootwait\0" \
+ "nfsargs=" \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath},v3,tcp\0" \
+ "mmc_mmc=" \
+ "if run mmcload mmcargs addargs ; then " \
+ "bootm ${loadaddr} - ${dtbaddr} ; " \
+ "fi\0" \
+ "mmc_nfs=" \
+ "if run mmcload nfsargs addip addargs ; then " \
+ "bootm ${loadaddr} - ${dtbaddr} ; " \
+ "fi\0" \
+ "sf_mmc=" \
+ "if run sfload mmcargs addargs ; then " \
+ "bootm ${loadaddr} - ${dtbaddr} ; " \
+ "fi\0" \
+ "sf_swu=" \
+ "if run sfload ; then " \
+ "sf read ${rdaddr} ${sf_swu_offset} ${sf_swu_size} ; " \
+ "setenv bootargs root=/dev/ram0 rw ; " \
+ "run addargs ; " \
+ "bootm ${loadaddr} ${rdaddr} ; " \
+ "fi\0" \
+ "net_mmc=" \
+ "if run netload mmcargs addargs ; then " \
+ "bootm ${loadaddr} - ${dtbaddr} ; " \
+ "fi\0" \
+ "net_nfs=" \
+ "if run netload nfsargs addip addargs ; then " \
+ "bootm ${loadaddr} - ${dtbaddr} ; " \
+ "fi\0" \
+ "prebootcmd=" \
+ "if test \"${envsaved}\" != y ; then ; " \
+ "setenv envsaved y ; " \
+ "saveenv ; " \
+ "fi ; " \
+ "if test \"${bootmode}\" = normal ; then " \
+ "setenv bootdelay 0 ; " \
+ "setenv bootpri mmc_mmc ; " \
+ "elif test \"${bootmode}\" = devel ; then " \
+ "setenv bootdelay 3 ; " \
+ "setenv bootpri net_mmc ; " \
+ "else " \
+ "if test \"${bootmode}\" != update ; then " \
+ "echo Warning: unknown bootmode \"${bootmode}\" ; " \
+ "fi ; " \
+ "setenv bootdelay 1 ; " \
+ "setenv bootpri sf_swu ; " \
+ "fi\0"
+
+/* The rest of the configuration is shared */
+#include <configs/mxs.h>
+
+#endif /* __CONFIGS_XEA_H__ */
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __DT_FSL_IMX_AUDMUX_H
+#define __DT_FSL_IMX_AUDMUX_H
+
+#define MX27_AUDMUX_HPCR1_SSI0 0
+#define MX27_AUDMUX_HPCR2_SSI1 1
+#define MX27_AUDMUX_HPCR3_SSI_PINS_4 2
+#define MX27_AUDMUX_PPCR1_SSI_PINS_1 3
+#define MX27_AUDMUX_PPCR2_SSI_PINS_2 4
+#define MX27_AUDMUX_PPCR3_SSI_PINS_3 5
+
+#define MX31_AUDMUX_PORT1_SSI0 0
+#define MX31_AUDMUX_PORT2_SSI1 1
+#define MX31_AUDMUX_PORT3_SSI_PINS_3 2
+#define MX31_AUDMUX_PORT4_SSI_PINS_4 3
+#define MX31_AUDMUX_PORT5_SSI_PINS_5 4
+#define MX31_AUDMUX_PORT6_SSI_PINS_6 5
+#define MX31_AUDMUX_PORT7_SSI_PINS_7 6
+
+#define MX51_AUDMUX_PORT1_SSI0 0
+#define MX51_AUDMUX_PORT2_SSI1 1
+#define MX51_AUDMUX_PORT3 2
+#define MX51_AUDMUX_PORT4 3
+#define MX51_AUDMUX_PORT5 4
+#define MX51_AUDMUX_PORT6 5
+#define MX51_AUDMUX_PORT7 6
+
+/*
+ * TFCSEL/RFCSEL (i.MX27) or TFSEL/TCSEL/RFSEL/RCSEL (i.MX31/51/53/6Q)
+ * can be sourced from Rx/Tx.
+ */
+#define IMX_AUDMUX_RXFS 0x8
+#define IMX_AUDMUX_RXCLK 0x8
+
+/* Register definitions for the i.MX21/27 Digital Audio Multiplexer */
+#define IMX_AUDMUX_V1_PCR_INMMASK(x) ((x) & 0xff)
+#define IMX_AUDMUX_V1_PCR_INMEN (1 << 8)
+#define IMX_AUDMUX_V1_PCR_TXRXEN (1 << 10)
+#define IMX_AUDMUX_V1_PCR_SYN (1 << 12)
+#define IMX_AUDMUX_V1_PCR_RXDSEL(x) (((x) & 0x7) << 13)
+#define IMX_AUDMUX_V1_PCR_RFCSEL(x) (((x) & 0xf) << 20)
+#define IMX_AUDMUX_V1_PCR_RCLKDIR (1 << 24)
+#define IMX_AUDMUX_V1_PCR_RFSDIR (1 << 25)
+#define IMX_AUDMUX_V1_PCR_TFCSEL(x) (((x) & 0xf) << 26)
+#define IMX_AUDMUX_V1_PCR_TCLKDIR (1 << 30)
+#define IMX_AUDMUX_V1_PCR_TFSDIR (1 << 31)
+
+/* Register definitions for the i.MX25/31/35/51 Digital Audio Multiplexer */
+#define IMX_AUDMUX_V2_PTCR_TFSDIR (1 << 31)
+#define IMX_AUDMUX_V2_PTCR_TFSEL(x) (((x) & 0xf) << 27)
+#define IMX_AUDMUX_V2_PTCR_TCLKDIR (1 << 26)
+#define IMX_AUDMUX_V2_PTCR_TCSEL(x) (((x) & 0xf) << 22)
+#define IMX_AUDMUX_V2_PTCR_RFSDIR (1 << 21)
+#define IMX_AUDMUX_V2_PTCR_RFSEL(x) (((x) & 0xf) << 17)
+#define IMX_AUDMUX_V2_PTCR_RCLKDIR (1 << 16)
+#define IMX_AUDMUX_V2_PTCR_RCSEL(x) (((x) & 0xf) << 12)
+#define IMX_AUDMUX_V2_PTCR_SYN (1 << 11)
+
+#define IMX_AUDMUX_V2_PDCR_RXDSEL(x) (((x) & 0x7) << 13)
+#define IMX_AUDMUX_V2_PDCR_TXRXEN (1 << 12)
+#define IMX_AUDMUX_V2_PDCR_MODE(x) (((x) & 0x3) << 8)
+#define IMX_AUDMUX_V2_PDCR_INMMASK(x) ((x) & 0xff)
+
+#endif /* __DT_FSL_IMX_AUDMUX_H */
CONFIG_GLOBAL_TIMER
CONFIG_GMII
CONFIG_GPCNTRL
-CONFIG_GPIO_ENABLE_SPI_FLASH
CONFIG_GPIO_LED_INVERTED_TABLE
CONFIG_GPIO_LED_STUBS
CONFIG_GREEN_LED
CONFIG_LEGACY
CONFIG_LEGACY_BOOTCMD_ENV
CONFIG_LG4573
-CONFIG_LG4573_BUS
-CONFIG_LG4573_CS
CONFIG_LINUX
CONFIG_LINUX_RESET_VEC
CONFIG_LITTLETON_LCD
blobs=`awk '/^SIGNED_HDMI/ {print $2} /^LOADER/ {print $2} /^SECOND_LOADER/ {print $2} /^DDR_FW/ {print $2}' $file`
for f in $blobs; do
- tmp=$srctree/$f
-
if [ $f = "spl/u-boot-spl-ddr.bin" ] || [ $f = "u-boot.itb" ]; then
continue
fi
if [ -f $f ]; then
continue
- fi
-
- if [ ! -f $tmp ]; then
+ else
echo "WARNING '$tmp' not found, resulting binary is not-functional" >&2
exit 1
fi
-
- sed -in "s;$f;$tmp;" $file
done
if [ $post_process = 1 ]; then
- if [ -f $srctree/lpddr4_pmu_train_1d_imem.bin ]; then
- objcopy -I binary -O binary --pad-to 0x8000 --gap-fill=0x0 $srctree/lpddr4_pmu_train_1d_imem.bin lpddr4_pmu_train_1d_imem_pad.bin
- objcopy -I binary -O binary --pad-to 0x4000 --gap-fill=0x0 $srctree/lpddr4_pmu_train_1d_dmem.bin lpddr4_pmu_train_1d_dmem_pad.bin
- objcopy -I binary -O binary --pad-to 0x8000 --gap-fill=0x0 $srctree/lpddr4_pmu_train_2d_imem.bin lpddr4_pmu_train_2d_imem_pad.bin
+ if [ -f lpddr4_pmu_train_1d_imem.bin ]; then
+ objcopy -I binary -O binary --pad-to 0x8000 --gap-fill=0x0 lpddr4_pmu_train_1d_imem.bin lpddr4_pmu_train_1d_imem_pad.bin
+ objcopy -I binary -O binary --pad-to 0x4000 --gap-fill=0x0 lpddr4_pmu_train_1d_dmem.bin lpddr4_pmu_train_1d_dmem_pad.bin
+ objcopy -I binary -O binary --pad-to 0x8000 --gap-fill=0x0 lpddr4_pmu_train_2d_imem.bin lpddr4_pmu_train_2d_imem_pad.bin
cat lpddr4_pmu_train_1d_imem_pad.bin lpddr4_pmu_train_1d_dmem_pad.bin > lpddr4_pmu_train_1d_fw.bin
- cat lpddr4_pmu_train_2d_imem_pad.bin $srctree/lpddr4_pmu_train_2d_dmem.bin > lpddr4_pmu_train_2d_fw.bin
+ cat lpddr4_pmu_train_2d_imem_pad.bin lpddr4_pmu_train_2d_dmem.bin > lpddr4_pmu_train_2d_fw.bin
dd if=spl/u-boot-spl.bin of=spl/u-boot-spl-pad.bin bs=4 conv=sync
cat spl/u-boot-spl-pad.bin lpddr4_pmu_train_1d_fw.bin lpddr4_pmu_train_2d_fw.bin > spl/u-boot-spl-ddr.bin
rm -f lpddr4_pmu_train_1d_fw.bin lpddr4_pmu_train_2d_fw.bin lpddr4_pmu_train_1d_imem_pad.bin lpddr4_pmu_train_1d_dmem_pad.bin lpddr4_pmu_train_2d_imem_pad.bin spl/u-boot-spl-pad.bin
fi
- if [ -f $srctree/ddr4_imem_1d.bin ]; then
- objcopy -I binary -O binary --pad-to 0x8000 --gap-fill=0x0 $srctree/ddr4_imem_1d.bin ddr4_imem_1d_pad.bin
- objcopy -I binary -O binary --pad-to 0x4000 --gap-fill=0x0 $srctree/ddr4_dmem_1d.bin ddr4_dmem_1d_pad.bin
- objcopy -I binary -O binary --pad-to 0x8000 --gap-fill=0x0 $srctree/ddr4_imem_2d.bin ddr4_imem_2d_pad.bin
+ if [ -f ddr4_imem_1d.bin ]; then
+ objcopy -I binary -O binary --pad-to 0x8000 --gap-fill=0x0 ddr4_imem_1d.bin ddr4_imem_1d_pad.bin
+ objcopy -I binary -O binary --pad-to 0x4000 --gap-fill=0x0 ddr4_dmem_1d.bin ddr4_dmem_1d_pad.bin
+ objcopy -I binary -O binary --pad-to 0x8000 --gap-fill=0x0 ddr4_imem_2d.bin ddr4_imem_2d_pad.bin
cat ddr4_imem_1d_pad.bin ddr4_dmem_1d_pad.bin > ddr4_1d_fw.bin
- cat ddr4_imem_2d_pad.bin $srctree/ddr4_dmem_2d.bin > ddr4_2d_fw.bin
+ cat ddr4_imem_2d_pad.bin ddr4_dmem_2d.bin > ddr4_2d_fw.bin
dd if=spl/u-boot-spl.bin of=spl/u-boot-spl-pad.bin bs=4 conv=sync
cat spl/u-boot-spl-pad.bin ddr4_1d_fw.bin ddr4_2d_fw.bin > spl/u-boot-spl-ddr.bin
rm -f ddr4_1d_fw.bin ddr4_2d_fw.bin ddr4_imem_1d_pad.bin ddr4_dmem_1d_pad.bin ddr4_imem_2d_pad.bin spl/u-boot-spl-pad.bin
projects / oweals / u-boot.git / commitdiff