add experimental support for 2.6.30
authorGabor Juhos <juhosg@openwrt.org>
Fri, 22 May 2009 08:38:10 +0000 (08:38 +0000)
committerGabor Juhos <juhosg@openwrt.org>
Fri, 22 May 2009 08:38:10 +0000 (08:38 +0000)
SVN-Revision: 15979

21 files changed:
target/linux/adm5120/patches-2.6.30/001-adm5120.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/002-adm5120_flash.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/003-adm5120_switch.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/005-adm5120_usb.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/007-adm5120_pci.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/009-adm5120_leds_switch_trigger.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/101-cfi_fixup_macronix_bootloc.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/102-jedec_pmc_39lvxxx_chips.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/103-mtd_trxsplit.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/120-rb153_cf_driver.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/140-cmdline_hack.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/200-amba_pl010_hacks.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/201-amba_bus_hacks.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/202-pci_disable_common_quirks.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/203-gpio_leds_brightness.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/310-adm5120_wdt.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/800-adm5120-remove-amba-bus-id.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/801-adm5120-flash-remove-bus-id.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.30/802-adm5120-switch-remove-redundant-napi-functions.patch [new file with mode: 0644]
target/linux/adm5120/router_be/config-2.6.30 [new file with mode: 0644]
target/linux/adm5120/router_le/config-2.6.30 [new file with mode: 0644]

diff --git a/target/linux/adm5120/patches-2.6.30/001-adm5120.patch b/target/linux/adm5120/patches-2.6.30/001-adm5120.patch
new file mode 100644 (file)
index 0000000..6b59bc7
--- /dev/null
@@ -0,0 +1,56 @@
+--- a/arch/mips/Kconfig
++++ b/arch/mips/Kconfig
+@@ -19,6 +19,21 @@ choice
+       prompt "System type"
+       default SGI_IP22
++config ADM5120
++      bool "Infineon/ADMtek ADM5120 SoC based machines"
++      select CEVT_R4K
++      select CSRC_R4K
++      select SYS_HAS_CPU_MIPS32_R1
++      select SYS_HAS_EARLY_PRINTK
++      select DMA_NONCOHERENT
++      select IRQ_CPU
++      select SYS_SUPPORTS_LITTLE_ENDIAN
++      select SYS_SUPPORTS_BIG_ENDIAN
++      select SYS_SUPPORTS_32BIT_KERNEL
++      select ARCH_REQUIRE_GPIOLIB
++      select SWAP_IO_SPACE if CPU_BIG_ENDIAN
++      select MIPS_MACHINE
++
+ config MACH_ALCHEMY
+       bool "Alchemy processor based machines"
+@@ -632,6 +647,7 @@ config CAVIUM_OCTEON_REFERENCE_BOARD
+ endchoice
++source "arch/mips/adm5120/Kconfig"
+ source "arch/mips/alchemy/Kconfig"
+ source "arch/mips/basler/excite/Kconfig"
+ source "arch/mips/jazz/Kconfig"
+--- a/arch/mips/Makefile
++++ b/arch/mips/Makefile
+@@ -181,6 +181,21 @@ cflags-$(CONFIG_MACH_JAZZ)        += -I$(srctre
+ load-$(CONFIG_MACH_JAZZ)      += 0xffffffff80080000
+ #
++# Infineon/ADMtek ADM5120
++#
++libs-$(CONFIG_ADM5120)                        += arch/mips/adm5120/prom/
++core-$(CONFIG_ADM5120)                        += arch/mips/adm5120/common/
++core-$(CONFIG_ADM5120_OEM_CELLVISION) += arch/mips/adm5120/cellvision/
++core-$(CONFIG_ADM5120_OEM_COMPEX)     += arch/mips/adm5120/compex/
++core-$(CONFIG_ADM5120_OEM_EDIMAX)     += arch/mips/adm5120/edimax/
++core-$(CONFIG_ADM5120_OEM_INFINEON)   += arch/mips/adm5120/infineon/
++core-$(CONFIG_ADM5120_OEM_MIKROTIK)   += arch/mips/adm5120/mikrotik/
++core-$(CONFIG_ADM5120_OEM_MOTOROLA)   += arch/mips/adm5120/motorola/
++core-$(CONFIG_ADM5120_OEM_ZYXEL)      += arch/mips/adm5120/zyxel/
++cflags-$(CONFIG_ADM5120)              += -I$(srctree)/arch/mips/include/asm/mach-adm5120
++load-$(CONFIG_ADM5120)                        += 0xffffffff80001000
++
++#
+ # Common Alchemy Au1x00 stuff
+ #
+ core-$(CONFIG_SOC_AU1X00)     += arch/mips/alchemy/common/
diff --git a/target/linux/adm5120/patches-2.6.30/002-adm5120_flash.patch b/target/linux/adm5120/patches-2.6.30/002-adm5120_flash.patch
new file mode 100644 (file)
index 0000000..97f5b96
--- /dev/null
@@ -0,0 +1,21 @@
+--- a/drivers/mtd/maps/Kconfig
++++ b/drivers/mtd/maps/Kconfig
+@@ -562,4 +562,8 @@ config MTD_VMU
+         To build this as a module select M here, the module will be called
+         vmu-flash.
++config MTD_ADM5120
++      tristate "Map driver for ADM5120 based boards"
++      depends on ADM5120
++
+ endmenu
+--- a/drivers/mtd/maps/Makefile
++++ b/drivers/mtd/maps/Makefile
+@@ -42,6 +42,7 @@ obj-$(CONFIG_MTD_DBOX2)              += dbox2-flash.
+ obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
+ obj-$(CONFIG_MTD_PCI)         += pci.o
+ obj-$(CONFIG_MTD_ALCHEMY)       += alchemy-flash.o
++obj-$(CONFIG_MTD_ADM5120)             += adm5120-flash.o
+ obj-$(CONFIG_MTD_AUTCPU12)    += autcpu12-nvram.o
+ obj-$(CONFIG_MTD_EDB7312)     += edb7312.o
+ obj-$(CONFIG_MTD_IMPA7)               += impa7.o
diff --git a/target/linux/adm5120/patches-2.6.30/003-adm5120_switch.patch b/target/linux/adm5120/patches-2.6.30/003-adm5120_switch.patch
new file mode 100644 (file)
index 0000000..771dd5f
--- /dev/null
@@ -0,0 +1,23 @@
+--- a/drivers/net/Kconfig
++++ b/drivers/net/Kconfig
+@@ -612,6 +612,10 @@ config MIPS_AU1X00_ENET
+         If you have an Alchemy Semi AU1X00 based system
+         say Y.  Otherwise, say N.
++config ADM5120_ENET
++      tristate "ADM5120 Ethernet switch support"
++      depends on ADM5120
++
+ config SGI_IOC3_ETH
+       bool "SGI IOC3 Ethernet"
+       depends on PCI && SGI_IP27
+--- a/drivers/net/Makefile
++++ b/drivers/net/Makefile
+@@ -195,6 +195,7 @@ obj-$(CONFIG_SC92031) += sc92031.o
+ # This is also a 82596 and should probably be merged
+ obj-$(CONFIG_LP486E) += lp486e.o
++obj-$(CONFIG_ADM5120_ENET) += adm5120sw.o
+ obj-$(CONFIG_ETH16I) += eth16i.o
+ obj-$(CONFIG_ZORRO8390) += zorro8390.o 8390.o
+ obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
diff --git a/target/linux/adm5120/patches-2.6.30/005-adm5120_usb.patch b/target/linux/adm5120/patches-2.6.30/005-adm5120_usb.patch
new file mode 100644 (file)
index 0000000..1e4bf00
--- /dev/null
@@ -0,0 +1,33 @@
+--- a/drivers/usb/Makefile
++++ b/drivers/usb/Makefile
+@@ -9,6 +9,7 @@ obj-$(CONFIG_USB)              += core/
+ obj-$(CONFIG_USB_MON)         += mon/
+ obj-$(CONFIG_PCI)             += host/
++obj-$(CONFIG_USB_ADM5120_HCD) += host/
+ obj-$(CONFIG_USB_EHCI_HCD)    += host/
+ obj-$(CONFIG_USB_ISP116X_HCD) += host/
+ obj-$(CONFIG_USB_ISP1760_HCD) += host/
+--- a/drivers/usb/host/Kconfig
++++ b/drivers/usb/host/Kconfig
+@@ -4,6 +4,10 @@
+ comment "USB Host Controller Drivers"
+       depends on USB
++config USB_ADM5120_HCD
++      tristate "ADM5120 HCD support (EXPERIMENTAL)"
++      depends on USB && ADM5120 && EXPERIMENTAL
++
+ config USB_C67X00_HCD
+       tristate "Cypress C67x00 HCD support"
+       depends on USB
+--- a/drivers/usb/host/Makefile
++++ b/drivers/usb/host/Makefile
+@@ -17,6 +17,7 @@ obj-$(CONFIG_USB_WHCI_HCD)   += whci/
+ obj-$(CONFIG_PCI)             += pci-quirks.o
++obj-$(CONFIG_USB_ADM5120_HCD) += adm5120-hcd.o
+ obj-$(CONFIG_USB_EHCI_HCD)    += ehci-hcd.o
+ obj-$(CONFIG_USB_OXU210HP_HCD)        += oxu210hp-hcd.o
+ obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
diff --git a/target/linux/adm5120/patches-2.6.30/007-adm5120_pci.patch b/target/linux/adm5120/patches-2.6.30/007-adm5120_pci.patch
new file mode 100644 (file)
index 0000000..7869c97
--- /dev/null
@@ -0,0 +1,19 @@
+--- a/arch/mips/pci/Makefile
++++ b/arch/mips/pci/Makefile
+@@ -52,3 +52,4 @@ obj-$(CONFIG_VICTOR_MPC30X)  += fixup-mpc
+ obj-$(CONFIG_ZAO_CAPCELLA)    += fixup-capcella.o
+ obj-$(CONFIG_WR_PPMC)         += fixup-wrppmc.o
+ obj-$(CONFIG_MIKROTIK_RB532)  += pci-rc32434.o ops-rc32434.o fixup-rc32434.o
++obj-$(CONFIG_ADM5120)         += pci-adm5120.o
+--- a/include/linux/pci_ids.h
++++ b/include/linux/pci_ids.h
+@@ -1764,6 +1764,9 @@
+ #define PCI_VENDOR_ID_ESDGMBH         0x12fe
+ #define PCI_DEVICE_ID_ESDGMBH_CPCIASIO4 0x0111
++#define PCI_VENDOR_ID_ADMTEK          0x1317
++#define PCI_DEVICE_ID_ADMTEK_ADM5120  0x5120
++
+ #define PCI_VENDOR_ID_SIIG            0x131f
+ #define PCI_SUBVENDOR_ID_SIIG         0x131f
+ #define PCI_DEVICE_ID_SIIG_1S_10x_550 0x1000
diff --git a/target/linux/adm5120/patches-2.6.30/009-adm5120_leds_switch_trigger.patch b/target/linux/adm5120/patches-2.6.30/009-adm5120_leds_switch_trigger.patch
new file mode 100644 (file)
index 0000000..4778dea
--- /dev/null
@@ -0,0 +1,22 @@
+--- a/drivers/leds/Kconfig
++++ b/drivers/leds/Kconfig
+@@ -306,4 +306,12 @@ config LEDS_TRIGGER_NETDEV
+         This allows LEDs to be controlled by network device activity.
+         If unsure, say Y.
++config LEDS_TRIGGER_ADM5120_SWITCH
++      tristate "LED ADM5120 Switch Port Status Trigger"
++      depends on LEDS_TRIGGERS && ADM5120
++      help
++        This allows LEDs to be controlled by the port states of
++        the ADM5120 built-in Ethernet Switch
++        If unsure, say N.
++
+ endif # NEW_LEDS
+--- a/drivers/leds/Makefile
++++ b/drivers/leds/Makefile
+@@ -40,3 +40,4 @@ obj-$(CONFIG_LEDS_TRIGGER_GPIO)              += ledt
+ obj-$(CONFIG_LEDS_TRIGGER_DEFAULT_ON) += ledtrig-default-on.o
+ obj-$(CONFIG_LEDS_TRIGGER_MORSE)      += ledtrig-morse.o
+ obj-$(CONFIG_LEDS_TRIGGER_NETDEV)      += ledtrig-netdev.o
++obj-$(CONFIG_LEDS_TRIGGER_ADM5120_SWITCH) += ledtrig-adm5120-switch.o
diff --git a/target/linux/adm5120/patches-2.6.30/101-cfi_fixup_macronix_bootloc.patch b/target/linux/adm5120/patches-2.6.30/101-cfi_fixup_macronix_bootloc.patch
new file mode 100644 (file)
index 0000000..60c3ab9
--- /dev/null
@@ -0,0 +1,84 @@
+--- a/drivers/mtd/chips/cfi_cmdset_0002.c
++++ b/drivers/mtd/chips/cfi_cmdset_0002.c
+@@ -53,6 +53,12 @@
+ #define AT49BV6416            0x00d6
+ #define MANUFACTURER_SAMSUNG  0x00ec
++/* Macronix */
++#define MX29LV160B    0x2249  /* MX29LV160 Bottom-boot chip */
++#define MX29LV160T    0x22C4  /* MX29LV160 Top-boot chip */
++#define MX29LV320B    0x22A8  /* MX29LV320 Bottom-boot chip */
++#define MX29LV320T    0x22A7  /* MX29LV320 Top-boot chip */
++
+ static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
+ static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
+ static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
+@@ -293,6 +299,41 @@ static void fixup_M29W128G_write_buffer(
+       }
+ }
++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++/*
++ * Some Macronix chips has no/bad bootblock information in the CFI table
++ */
++static void fixup_macronix_bootloc(struct mtd_info *mtd, void* param)
++{
++      struct map_info *map = mtd->priv;
++      struct cfi_private *cfi = map->fldrv_priv;
++      struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
++      __u8 t;
++
++      switch (cfi->id) {
++      /* TODO: put affected chip ids here */
++      case MX29LV160B:
++      case MX29LV320B:
++              t = 2;  /* Bottom boot */
++              break;
++      case MX29LV160T:
++      case MX29LV320T:
++              t = 3;  /* Top boot */
++              break;
++      default:
++              return;
++      }
++
++      if (extp->TopBottom == t)
++              /* boot location detected by the CFI layer is correct */
++              return;
++
++      extp->TopBottom = t;
++      printk("%s: Macronix chip detected, id:0x%04X, boot location forced "
++              "to %s\n", map->name, cfi->id, (t == 2) ? "bottom" : "top");
++}
++#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */
++
+ static struct cfi_fixup cfi_fixup_table[] = {
+       { CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri, NULL },
+ #ifdef AMD_BOOTLOC_BUG
+@@ -330,6 +371,9 @@ static struct cfi_fixup fixup_table[] = 
+        */
+       { CFI_MFR_ANY, CFI_ID_ANY, fixup_use_erase_chip, NULL },
+       { CFI_MFR_ATMEL, AT49BV6416, fixup_use_atmel_lock, NULL },
++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++      { MANUFACTURER_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc, NULL, },
++#endif
+       { 0, 0, NULL, NULL }
+ };
+--- a/drivers/mtd/chips/Kconfig
++++ b/drivers/mtd/chips/Kconfig
+@@ -198,6 +198,14 @@ config MTD_CFI_AMDSTD
+         provides support for one of those command sets, used on chips
+         including the AMD Am29LV320.
++config MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++      bool "Fix boot-block location for Macronix flash chips"
++      depends on MTD_CFI_AMDSTD
++      help
++        Some Macronix flash chips have no/wrong boot-block location in the
++        CFI table, and the driver may detect the type incorrectly. Select
++        this if your board has such chip.
++
+ config MTD_CFI_STAA
+       tristate "Support for ST (Advanced Architecture) flash chips"
+       depends on MTD_GEN_PROBE
diff --git a/target/linux/adm5120/patches-2.6.30/102-jedec_pmc_39lvxxx_chips.patch b/target/linux/adm5120/patches-2.6.30/102-jedec_pmc_39lvxxx_chips.patch
new file mode 100644 (file)
index 0000000..55a201d
--- /dev/null
@@ -0,0 +1,68 @@
+--- a/drivers/mtd/chips/jedec_probe.c
++++ b/drivers/mtd/chips/jedec_probe.c
+@@ -128,6 +128,10 @@
+ #define UPD29F064115  0x221C
+ /* PMC */
++#define PM39LV512     0x001B
++#define PM39LV010     0x001C
++#define PM39LV020     0x003D
++#define PM39LV040     0x003E
+ #define PM49FL002     0x006D
+ #define PM49FL004     0x006E
+ #define PM49FL008     0x006A
+@@ -1249,6 +1253,54 @@ static const struct amd_flash_info jedec
+                       ERASEINFO(0x02000,2),
+                       ERASEINFO(0x04000,1),
+               }
++        }, {
++              .mfr_id         = MANUFACTURER_PMC,
++              .dev_id         = PM39LV512,
++              .name           = "PMC Pm39LV512",
++              .devtypes       = CFI_DEVICETYPE_X8,
++              .uaddr          = MTD_UADDR_0x0555_0x02AA,
++              .dev_size       = SIZE_64KiB,
++              .cmd_set        = P_ID_AMD_STD,
++              .nr_regions     = 1,
++              .regions        = {
++                      ERASEINFO(0x01000,16),
++              }
++        }, {
++              .mfr_id         = MANUFACTURER_PMC,
++              .dev_id         = PM39LV010,
++              .name           = "PMC Pm39LV010",
++              .devtypes       = CFI_DEVICETYPE_X8,
++              .uaddr          = MTD_UADDR_0x0555_0x02AA,
++              .dev_size       = SIZE_128KiB,
++              .cmd_set        = P_ID_AMD_STD,
++              .nr_regions     = 1,
++              .regions        = {
++                      ERASEINFO(0x01000,32),
++              }
++        }, {
++              .mfr_id         = MANUFACTURER_PMC,
++              .dev_id         = PM39LV020,
++              .name           = "PMC Pm39LV020",
++              .devtypes       = CFI_DEVICETYPE_X8,
++              .uaddr          = MTD_UADDR_0x0555_0x02AA,
++              .dev_size       = SIZE_256KiB,
++              .cmd_set        = P_ID_AMD_STD,
++              .nr_regions     = 1,
++              .regions        = {
++                      ERASEINFO(0x01000,64),
++              }
++        }, {
++              .mfr_id         = MANUFACTURER_PMC,
++              .dev_id         = PM39LV040,
++              .name           = "PMC Pm39LV040",
++              .devtypes       = CFI_DEVICETYPE_X8,
++              .uaddr          = MTD_UADDR_0x0555_0x02AA,
++              .dev_size       = SIZE_512KiB,
++              .cmd_set        = P_ID_AMD_STD,
++              .nr_regions     = 1,
++              .regions        = {
++                      ERASEINFO(0x01000,128),
++              }
+       }, {
+               .mfr_id         = MANUFACTURER_PMC,
+               .dev_id         = PM49FL002,
diff --git a/target/linux/adm5120/patches-2.6.30/103-mtd_trxsplit.patch b/target/linux/adm5120/patches-2.6.30/103-mtd_trxsplit.patch
new file mode 100644 (file)
index 0000000..69f1035
--- /dev/null
@@ -0,0 +1,24 @@
+--- a/drivers/mtd/Kconfig
++++ b/drivers/mtd/Kconfig
+@@ -63,6 +63,11 @@ config MTD_ROOTFS_SPLIT
+       depends on MTD_PARTITIONS
+       default y
++config MTD_TRXSPLIT
++      bool "Automatically find and split TRX partitions"
++      depends on MTD_PARTITIONS
++      default n
++
+ config MTD_REDBOOT_PARTS
+       tristate "RedBoot partition table parsing"
+       depends on MTD_PARTITIONS
+--- a/drivers/mtd/Makefile
++++ b/drivers/mtd/Makefile
+@@ -8,6 +8,7 @@ mtd-y                          := mtdcore.o mtdsuper.o mtdbdi.
+ mtd-$(CONFIG_MTD_PARTITIONS)  += mtdpart.o
+ obj-$(CONFIG_MTD_CONCAT)      += mtdconcat.o
++obj-$(CONFIG_MTD_TRXSPLIT)    += trxsplit.o
+ obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o
+ obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
+ obj-$(CONFIG_MTD_AFS_PARTS)   += afs.o
diff --git a/target/linux/adm5120/patches-2.6.30/120-rb153_cf_driver.patch b/target/linux/adm5120/patches-2.6.30/120-rb153_cf_driver.patch
new file mode 100644 (file)
index 0000000..3d9bbdd
--- /dev/null
@@ -0,0 +1,28 @@
+--- a/drivers/ata/Makefile
++++ b/drivers/ata/Makefile
+@@ -73,6 +73,7 @@ obj-$(CONFIG_PATA_OCTEON_CF) += pata_oct
+ obj-$(CONFIG_PATA_PLATFORM)   += pata_platform.o
+ obj-$(CONFIG_PATA_OF_PLATFORM)        += pata_of_platform.o
+ obj-$(CONFIG_PATA_ICSIDE)     += pata_icside.o
++obj-$(CONFIG_PATA_RB153_CF)   += pata_rb153_cf.o
+ # Should be last but two libata driver
+ obj-$(CONFIG_PATA_ACPI)               += pata_acpi.o
+ # Should be last but one libata driver
+--- a/drivers/ata/Kconfig
++++ b/drivers/ata/Kconfig
+@@ -568,6 +568,15 @@ config PATA_RADISYS
+         If unsure, say N.
++config PATA_RB153_CF
++      tristate "RouterBOARD 153 Compact Flash support"
++      depends on ADM5120_MACH_RB_153
++      help
++        This option enables support for a Compact Flash connected on
++        the RouterBOARD 153.
++
++        If unsure, say N.
++
+ config PATA_RB532
+       tristate "RouterBoard 532 PATA CompactFlash support"
+       depends on MIKROTIK_RB532
diff --git a/target/linux/adm5120/patches-2.6.30/140-cmdline_hack.patch b/target/linux/adm5120/patches-2.6.30/140-cmdline_hack.patch
new file mode 100644 (file)
index 0000000..14172fc
--- /dev/null
@@ -0,0 +1,15 @@
+--- a/arch/mips/kernel/head.S
++++ b/arch/mips/kernel/head.S
+@@ -127,7 +127,12 @@
+       /*
+        * Reserved space for exception handlers.
+        * Necessary for machines which link their kernels at KSEG0.
++       * Use as temporary storage for the kernel command line, so that it
++       * can be updated easily without having to relink the kernel.
+        */
++
++EXPORT(_image_cmdline)
++      .ascii "CMDLINE:"
+       .fill   0x400
+ #endif
diff --git a/target/linux/adm5120/patches-2.6.30/200-amba_pl010_hacks.patch b/target/linux/adm5120/patches-2.6.30/200-amba_pl010_hacks.patch
new file mode 100644 (file)
index 0000000..2857644
--- /dev/null
@@ -0,0 +1,378 @@
+--- a/drivers/serial/amba-pl010.c
++++ b/drivers/serial/amba-pl010.c
+@@ -50,11 +50,10 @@
+ #include <asm/io.h>
+-#define UART_NR               8
+-
+ #define SERIAL_AMBA_MAJOR     204
+ #define SERIAL_AMBA_MINOR     16
+-#define SERIAL_AMBA_NR                UART_NR
++#define SERIAL_AMBA_NR                CONFIG_SERIAL_AMBA_PL010_NUMPORTS
++#define SERIAL_AMBA_NAME      CONFIG_SERIAL_AMBA_PL010_PORTNAME
+ #define AMBA_ISR_PASS_LIMIT   256
+@@ -80,9 +79,9 @@ static void pl010_stop_tx(struct uart_po
+       struct uart_amba_port *uap = (struct uart_amba_port *)port;
+       unsigned int cr;
+-      cr = readb(uap->port.membase + UART010_CR);
++      cr = __raw_readl(uap->port.membase + UART010_CR);
+       cr &= ~UART010_CR_TIE;
+-      writel(cr, uap->port.membase + UART010_CR);
++      __raw_writel(cr, uap->port.membase + UART010_CR);
+ }
+ static void pl010_start_tx(struct uart_port *port)
+@@ -90,9 +89,9 @@ static void pl010_start_tx(struct uart_p
+       struct uart_amba_port *uap = (struct uart_amba_port *)port;
+       unsigned int cr;
+-      cr = readb(uap->port.membase + UART010_CR);
++      cr = __raw_readl(uap->port.membase + UART010_CR);
+       cr |= UART010_CR_TIE;
+-      writel(cr, uap->port.membase + UART010_CR);
++      __raw_writel(cr, uap->port.membase + UART010_CR);
+ }
+ static void pl010_stop_rx(struct uart_port *port)
+@@ -100,9 +99,9 @@ static void pl010_stop_rx(struct uart_po
+       struct uart_amba_port *uap = (struct uart_amba_port *)port;
+       unsigned int cr;
+-      cr = readb(uap->port.membase + UART010_CR);
++      cr = __raw_readl(uap->port.membase + UART010_CR);
+       cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
+-      writel(cr, uap->port.membase + UART010_CR);
++      __raw_writel(cr, uap->port.membase + UART010_CR);
+ }
+ static void pl010_enable_ms(struct uart_port *port)
+@@ -110,9 +109,9 @@ static void pl010_enable_ms(struct uart_
+       struct uart_amba_port *uap = (struct uart_amba_port *)port;
+       unsigned int cr;
+-      cr = readb(uap->port.membase + UART010_CR);
++      cr = __raw_readl(uap->port.membase + UART010_CR);
+       cr |= UART010_CR_MSIE;
+-      writel(cr, uap->port.membase + UART010_CR);
++      __raw_writel(cr, uap->port.membase + UART010_CR);
+ }
+ static void pl010_rx_chars(struct uart_amba_port *uap)
+@@ -120,9 +119,9 @@ static void pl010_rx_chars(struct uart_a
+       struct tty_struct *tty = uap->port.info->port.tty;
+       unsigned int status, ch, flag, rsr, max_count = 256;
+-      status = readb(uap->port.membase + UART01x_FR);
++      status = __raw_readl(uap->port.membase + UART01x_FR);
+       while (UART_RX_DATA(status) && max_count--) {
+-              ch = readb(uap->port.membase + UART01x_DR);
++              ch = __raw_readl(uap->port.membase + UART01x_DR);
+               flag = TTY_NORMAL;
+               uap->port.icount.rx++;
+@@ -131,9 +130,9 @@ static void pl010_rx_chars(struct uart_a
+                * Note that the error handling code is
+                * out of the main execution path
+                */
+-              rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
++              rsr = __raw_readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
+               if (unlikely(rsr & UART01x_RSR_ANY)) {
+-                      writel(0, uap->port.membase + UART01x_ECR);
++                      __raw_writel(0, uap->port.membase + UART01x_ECR);
+                       if (rsr & UART01x_RSR_BE) {
+                               rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE);
+@@ -163,7 +162,7 @@ static void pl010_rx_chars(struct uart_a
+               uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
+       ignore_char:
+-              status = readb(uap->port.membase + UART01x_FR);
++              status = __raw_readl(uap->port.membase + UART01x_FR);
+       }
+       spin_unlock(&uap->port.lock);
+       tty_flip_buffer_push(tty);
+@@ -176,7 +175,7 @@ static void pl010_tx_chars(struct uart_a
+       int count;
+       if (uap->port.x_char) {
+-              writel(uap->port.x_char, uap->port.membase + UART01x_DR);
++              __raw_writel(uap->port.x_char, uap->port.membase + UART01x_DR);
+               uap->port.icount.tx++;
+               uap->port.x_char = 0;
+               return;
+@@ -188,7 +187,7 @@ static void pl010_tx_chars(struct uart_a
+       count = uap->port.fifosize >> 1;
+       do {
+-              writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
++              __raw_writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
+               xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+               uap->port.icount.tx++;
+               if (uart_circ_empty(xmit))
+@@ -206,9 +205,9 @@ static void pl010_modem_status(struct ua
+ {
+       unsigned int status, delta;
+-      writel(0, uap->port.membase + UART010_ICR);
++      __raw_writel(0, uap->port.membase + UART010_ICR);
+-      status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
++      status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+       delta = status ^ uap->old_status;
+       uap->old_status = status;
+@@ -236,7 +235,7 @@ static irqreturn_t pl010_int(int irq, vo
+       spin_lock(&uap->port.lock);
+-      status = readb(uap->port.membase + UART010_IIR);
++      status = __raw_readl(uap->port.membase + UART010_IIR);
+       if (status) {
+               do {
+                       if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
+@@ -249,7 +248,7 @@ static irqreturn_t pl010_int(int irq, vo
+                       if (pass_counter-- == 0)
+                               break;
+-                      status = readb(uap->port.membase + UART010_IIR);
++                      status = __raw_readl(uap->port.membase + UART010_IIR);
+               } while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
+                                  UART010_IIR_TIS));
+               handled = 1;
+@@ -263,7 +262,7 @@ static irqreturn_t pl010_int(int irq, vo
+ static unsigned int pl010_tx_empty(struct uart_port *port)
+ {
+       struct uart_amba_port *uap = (struct uart_amba_port *)port;
+-      unsigned int status = readb(uap->port.membase + UART01x_FR);
++      unsigned int status = __raw_readl(uap->port.membase + UART01x_FR);
+       return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
+ }
+@@ -273,7 +272,7 @@ static unsigned int pl010_get_mctrl(stru
+       unsigned int result = 0;
+       unsigned int status;
+-      status = readb(uap->port.membase + UART01x_FR);
++      status = __raw_readl(uap->port.membase + UART01x_FR);
+       if (status & UART01x_FR_DCD)
+               result |= TIOCM_CAR;
+       if (status & UART01x_FR_DSR)
+@@ -299,12 +298,12 @@ static void pl010_break_ctl(struct uart_
+       unsigned int lcr_h;
+       spin_lock_irqsave(&uap->port.lock, flags);
+-      lcr_h = readb(uap->port.membase + UART010_LCRH);
++      lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
+       if (break_state == -1)
+               lcr_h |= UART01x_LCRH_BRK;
+       else
+               lcr_h &= ~UART01x_LCRH_BRK;
+-      writel(lcr_h, uap->port.membase + UART010_LCRH);
++      __raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
+       spin_unlock_irqrestore(&uap->port.lock, flags);
+ }
+@@ -332,12 +331,12 @@ static int pl010_startup(struct uart_por
+       /*
+        * initialise the old status of the modem signals
+        */
+-      uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
++      uap->old_status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+       /*
+        * Finally, enable interrupts
+        */
+-      writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
++      __raw_writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
+              uap->port.membase + UART010_CR);
+       return 0;
+@@ -360,10 +359,10 @@ static void pl010_shutdown(struct uart_p
+       /*
+        * disable all interrupts, disable the port
+        */
+-      writel(0, uap->port.membase + UART010_CR);
++      __raw_writel(0, uap->port.membase + UART010_CR);
+       /* disable break condition and fifos */
+-      writel(readb(uap->port.membase + UART010_LCRH) &
++      __raw_writel(__raw_readl(uap->port.membase + UART010_LCRH) &
+               ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
+              uap->port.membase + UART010_LCRH);
+@@ -385,7 +384,7 @@ pl010_set_termios(struct uart_port *port
+       /*
+        * Ask the core to calculate the divisor for us.
+        */
+-      baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16); 
++      baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
+       quot = uart_get_divisor(port, baud);
+       switch (termios->c_cflag & CSIZE) {
+@@ -448,25 +447,25 @@ pl010_set_termios(struct uart_port *port
+               uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
+       /* first, disable everything */
+-      old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
++      old_cr = __raw_readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
+       if (UART_ENABLE_MS(port, termios->c_cflag))
+               old_cr |= UART010_CR_MSIE;
+-      writel(0, uap->port.membase + UART010_CR);
++      __raw_writel(0, uap->port.membase + UART010_CR);
+       /* Set baud rate */
+       quot -= 1;
+-      writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
+-      writel(quot & 0xff, uap->port.membase + UART010_LCRL);
++      __raw_writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
++      __raw_writel(quot & 0xff, uap->port.membase + UART010_LCRL);
+       /*
+        * ----------v----------v----------v----------v-----
+        * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
+        * ----------^----------^----------^----------^-----
+        */
+-      writel(lcr_h, uap->port.membase + UART010_LCRH);
+-      writel(old_cr, uap->port.membase + UART010_CR);
++      __raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
++      __raw_writel(old_cr, uap->port.membase + UART010_CR);
+       spin_unlock_irqrestore(&uap->port.lock, flags);
+ }
+@@ -538,7 +537,7 @@ static struct uart_ops amba_pl010_pops =
+       .verify_port    = pl010_verify_port,
+ };
+-static struct uart_amba_port *amba_ports[UART_NR];
++static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR];
+ #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE
+@@ -548,10 +547,10 @@ static void pl010_console_putchar(struct
+       unsigned int status;
+       do {
+-              status = readb(uap->port.membase + UART01x_FR);
++              status = __raw_readl(uap->port.membase + UART01x_FR);
+               barrier();
+       } while (!UART_TX_READY(status));
+-      writel(ch, uap->port.membase + UART01x_DR);
++      __raw_writel(ch, uap->port.membase + UART01x_DR);
+ }
+ static void
+@@ -565,8 +564,8 @@ pl010_console_write(struct console *co, 
+       /*
+        *      First save the CR then disable the interrupts
+        */
+-      old_cr = readb(uap->port.membase + UART010_CR);
+-      writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
++      old_cr = __raw_readl(uap->port.membase + UART010_CR);
++      __raw_writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
+       uart_console_write(&uap->port, s, count, pl010_console_putchar);
+@@ -575,10 +574,10 @@ pl010_console_write(struct console *co, 
+        *      and restore the TCR
+        */
+       do {
+-              status = readb(uap->port.membase + UART01x_FR);
++              status = __raw_readl(uap->port.membase + UART01x_FR);
+               barrier();
+       } while (status & UART01x_FR_BUSY);
+-      writel(old_cr, uap->port.membase + UART010_CR);
++      __raw_writel(old_cr, uap->port.membase + UART010_CR);
+       clk_disable(uap->clk);
+ }
+@@ -587,9 +586,9 @@ static void __init
+ pl010_console_get_options(struct uart_amba_port *uap, int *baud,
+                            int *parity, int *bits)
+ {
+-      if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
++      if (__raw_readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
+               unsigned int lcr_h, quot;
+-              lcr_h = readb(uap->port.membase + UART010_LCRH);
++              lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
+               *parity = 'n';
+               if (lcr_h & UART01x_LCRH_PEN) {
+@@ -604,8 +603,8 @@ pl010_console_get_options(struct uart_am
+               else
+                       *bits = 8;
+-              quot = readb(uap->port.membase + UART010_LCRL) |
+-                     readb(uap->port.membase + UART010_LCRM) << 8;
++              quot = __raw_readl(uap->port.membase + UART010_LCRL) |
++                     __raw_readl(uap->port.membase + UART010_LCRM) << 8;
+               *baud = uap->port.uartclk / (16 * (quot + 1));
+       }
+ }
+@@ -623,7 +622,7 @@ static int __init pl010_console_setup(st
+        * if so, search for the first available port that does have
+        * console support.
+        */
+-      if (co->index >= UART_NR)
++      if (co->index >= SERIAL_AMBA_NR)
+               co->index = 0;
+       uap = amba_ports[co->index];
+       if (!uap)
+@@ -641,7 +640,7 @@ static int __init pl010_console_setup(st
+ static struct uart_driver amba_reg;
+ static struct console amba_console = {
+-      .name           = "ttyAM",
++      .name           = SERIAL_AMBA_NAME,
+       .write          = pl010_console_write,
+       .device         = uart_console_device,
+       .setup          = pl010_console_setup,
+@@ -657,11 +656,11 @@ static struct console amba_console = {
+ static struct uart_driver amba_reg = {
+       .owner                  = THIS_MODULE,
+-      .driver_name            = "ttyAM",
+-      .dev_name               = "ttyAM",
++      .driver_name            = SERIAL_AMBA_NAME,
++      .dev_name               = SERIAL_AMBA_NAME,
+       .major                  = SERIAL_AMBA_MAJOR,
+       .minor                  = SERIAL_AMBA_MINOR,
+-      .nr                     = UART_NR,
++      .nr                     = SERIAL_AMBA_NR,
+       .cons                   = AMBA_CONSOLE,
+ };
+--- a/drivers/serial/Kconfig
++++ b/drivers/serial/Kconfig
+@@ -284,10 +284,25 @@ config SERIAL_AMBA_PL010
+       help
+         This selects the ARM(R) AMBA(R) PrimeCell PL010 UART.  If you have
+         an Integrator/AP or Integrator/PP2 platform, or if you have a
+-        Cirrus Logic EP93xx CPU, say Y or M here.
++        Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here.
+         If unsure, say N.
++config SERIAL_AMBA_PL010_NUMPORTS
++      int "Maximum number of AMBA PL010 serial ports"
++      depends on SERIAL_AMBA_PL010
++      default "8"
++      ---help---
++        Set this to the number of serial ports you want the AMBA PL010 driver
++        to support.
++
++config SERIAL_AMBA_PL010_PORTNAME
++      string "Name of the AMBA PL010 serial ports"
++      depends on SERIAL_AMBA_PL010
++      default "ttyAM"
++      ---help---
++        ::: To be written :::
++
+ config SERIAL_AMBA_PL010_CONSOLE
+       bool "Support for console on AMBA serial port"
+       depends on SERIAL_AMBA_PL010=y
diff --git a/target/linux/adm5120/patches-2.6.30/201-amba_bus_hacks.patch b/target/linux/adm5120/patches-2.6.30/201-amba_bus_hacks.patch
new file mode 100644 (file)
index 0000000..9db3e55
--- /dev/null
@@ -0,0 +1,13 @@
+--- a/drivers/amba/bus.c
++++ b/drivers/amba/bus.c
+@@ -18,6 +18,10 @@
+ #include <asm/irq.h>
+ #include <asm/sizes.h>
++#ifndef NO_IRQ
++#define NO_IRQ                (-1)
++#endif
++
+ #define to_amba_device(d)     container_of(d, struct amba_device, dev)
+ #define to_amba_driver(d)     container_of(d, struct amba_driver, drv)
diff --git a/target/linux/adm5120/patches-2.6.30/202-pci_disable_common_quirks.patch b/target/linux/adm5120/patches-2.6.30/202-pci_disable_common_quirks.patch
new file mode 100644 (file)
index 0000000..4e63283
--- /dev/null
@@ -0,0 +1,191 @@
+--- a/drivers/pci/Kconfig
++++ b/drivers/pci/Kconfig
+@@ -51,6 +51,12 @@ config PCI_STUB
+         When in doubt, say N.
++config PCI_DISABLE_COMMON_QUIRKS
++      bool "PCI disable common quirks"
++      depends on PCI
++      help
++        If you don't know what to do here, say N.
++
+ config HT_IRQ
+       bool "Interrupts on hypertransport devices"
+       default y
+--- a/drivers/pci/quirks.c
++++ b/drivers/pci/quirks.c
+@@ -98,6 +98,7 @@ static void __devinit quirk_resource_ali
+ }
+ DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_resource_alignment);
++#ifndef CONFIG_PCI_DISABLE_COMMON_QUIRKS
+ /* The Mellanox Tavor device gives false positive parity errors
+  * Mark this device with a broken_parity_status, to allow
+  * PCI scanning code to "skip" this now blacklisted device.
+@@ -132,11 +133,11 @@ DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_I
+ /*  The VIA VP2/VP3/MVP3 seem to have some 'features'. There may be a workaround
+     but VIA don't answer queries. If you happen to have good contacts at VIA
+-    ask them for me please -- Alan 
+-    
+-    This appears to be BIOS not version dependent. So presumably there is a 
++    ask them for me please -- Alan
++
++    This appears to be BIOS not version dependent. So presumably there is a
+     chipset level fix */
+-    
++
+ static void __devinit quirk_isa_dma_hangs(struct pci_dev *dev)
+ {
+       if (!isa_dma_bridge_buggy) {
+@@ -204,7 +205,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_IN
+  *      the info on which Mr Breese based his work.
+  *
+  *    Updated based on further information from the site and also on
+- *    information provided by VIA 
++ *    information provided by VIA
+  */
+ static void quirk_vialatency(struct pci_dev *dev)
+ {
+@@ -212,7 +213,7 @@ static void quirk_vialatency(struct pci_
+       u8 busarb;
+       /* Ok we have a potential problem chipset here. Now see if we have
+          a buggy southbridge */
+-         
++
+       p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, NULL);
+       if (p!=NULL) {
+               /* 0x40 - 0x4f == 686B, 0x10 - 0x2f == 686A; thanks Dan Hollis */
+@@ -227,9 +228,9 @@ static void quirk_vialatency(struct pci_
+               if (p->revision < 0x10 || p->revision > 0x12)
+                       goto exit;
+       }
+-      
++
+       /*
+-       *      Ok we have the problem. Now set the PCI master grant to 
++       *      Ok we have the problem. Now set the PCI master grant to
+        *      occur every master grant. The apparent bug is that under high
+        *      PCI load (quite common in Linux of course) you can get data
+        *      loss when the CPU is held off the bus for 3 bus master requests
+@@ -242,7 +243,7 @@ static void quirk_vialatency(struct pci_
+        */
+       pci_read_config_byte(dev, 0x76, &busarb);
+-      /* Set bit 4 and bi 5 of byte 76 to 0x01 
++      /* Set bit 4 and bi 5 of byte 76 to 0x01
+          "Master priority rotation on every PCI master grant */
+       busarb &= ~(1<<5);
+       busarb |= (1<<4);
+@@ -285,7 +286,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VI
+  *    that DMA to AGP space. Latency must be set to 0xA and triton
+  *    workaround applied too
+  *    [Info kindly provided by ALi]
+- */   
++ */
+ static void __init quirk_alimagik(struct pci_dev *dev)
+ {
+       if ((pci_pci_problems&PCIPCI_ALIMAGIK)==0) {
+@@ -361,7 +362,7 @@ static void __devinit quirk_io_region(st
+               pci_claim_resource(dev, nr);
+               dev_info(&dev->dev, "quirk: region %04x-%04x claimed by %s\n", region, region + size - 1, name);
+       }
+-}     
++}
+ /*
+  *    ATI Northbridge setups MCE the processor if you even
+@@ -418,7 +419,7 @@ static void piix4_io_quirk(struct pci_de
+       /*
+        * For now we only print it out. Eventually we'll want to
+        * reserve it (at least if it's in the 0x1000+ range), but
+-       * let's get enough confirmation reports first. 
++       * let's get enough confirmation reports first.
+        */
+       base &= -size;
+       dev_info(&dev->dev, "%s PIO at %04x-%04x\n", name, base, base + size - 1);
+@@ -443,7 +444,7 @@ static void piix4_mem_quirk(struct pci_d
+       }
+       /*
+        * For now we only print it out. Eventually we'll want to
+-       * reserve it, but let's get enough confirmation reports first. 
++       * reserve it, but let's get enough confirmation reports first.
+        */
+       base &= -size;
+       dev_info(&dev->dev, "%s MMIO at %04x-%04x\n", name, base, base + size - 1);
+@@ -673,7 +674,7 @@ static void __devinit quirk_vt8235_acpi(
+ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA,   PCI_DEVICE_ID_VIA_8235, quirk_vt8235_acpi);
+-#ifdef CONFIG_X86_IO_APIC 
++#ifdef CONFIG_X86_IO_APIC
+ #include <asm/io_apic.h>
+@@ -687,12 +688,12 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_V
+ static void quirk_via_ioapic(struct pci_dev *dev)
+ {
+       u8 tmp;
+-      
++
+       if (nr_ioapics < 1)
+               tmp = 0;    /* nothing routed to external APIC */
+       else
+               tmp = 0x1f; /* all known bits (4-0) routed to external APIC */
+-              
++
+       dev_info(&dev->dev, "%sbling VIA external APIC routing\n",
+              tmp == 0 ? "Disa" : "Ena");
+@@ -977,7 +978,7 @@ DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_C
+ static void quirk_disable_pxb(struct pci_dev *pdev)
+ {
+       u16 config;
+-      
++
+       if (pdev->revision != 0x04)             /* Only C0 requires this */
+               return;
+       pci_read_config_word(pdev, 0x40, &config);
+@@ -1073,11 +1074,11 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_I
+  * On ASUS P4B boards, the SMBus PCI Device within the ICH2/4 southbridge
+  * is not activated. The myth is that Asus said that they do not want the
+  * users to be irritated by just another PCI Device in the Win98 device
+- * manager. (see the file prog/hotplug/README.p4b in the lm_sensors 
++ * manager. (see the file prog/hotplug/README.p4b in the lm_sensors
+  * package 2.7.0 for details)
+  *
+- * The SMBus PCI Device can be activated by setting a bit in the ICH LPC 
+- * bridge. Unfortunately, this device has no subvendor/subdevice ID. So it 
++ * The SMBus PCI Device can be activated by setting a bit in the ICH LPC
++ * bridge. Unfortunately, this device has no subvendor/subdevice ID. So it
+  * becomes necessary to do this tweak in two steps -- the chosen trigger
+  * is either the Host bridge (preferred) or on-board VGA controller.
+  *
+@@ -1229,7 +1230,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_I
+ static void asus_hides_smbus_lpc(struct pci_dev *dev)
+ {
+       u16 val;
+-      
++
+       if (likely(!asus_hides_smbus))
+               return;
+@@ -1859,7 +1860,9 @@ static void __devinit fixup_rev1_53c810(
+       }
+ }
+ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810);
++#endif /* !CONFIG_PCI_DISABLE_COMMON_QUIRKS */
++#ifndef CONFIG_PCI_DISABLE_COMMON_QUIRKS
+ /* Enable 1k I/O space granularity on the Intel P64H2 */
+ static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev)
+ {
+@@ -2463,6 +2466,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_I
+ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x10e7, quirk_i82576_sriov);
+ #endif        /* CONFIG_PCI_IOV */
++#endif /* !CONFIG_PCI_DISABLE_COMMON_QUIRKS */
+ static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f,
+                         struct pci_fixup *end)
diff --git a/target/linux/adm5120/patches-2.6.30/203-gpio_leds_brightness.patch b/target/linux/adm5120/patches-2.6.30/203-gpio_leds_brightness.patch
new file mode 100644 (file)
index 0000000..8bccf39
--- /dev/null
@@ -0,0 +1,27 @@
+--- a/drivers/leds/leds-gpio.c
++++ b/drivers/leds/leds-gpio.c
+@@ -44,13 +44,17 @@ static void gpio_led_set(struct led_clas
+               container_of(led_cdev, struct gpio_led_data, cdev);
+       int level;
+-      if (value == LED_OFF)
+-              level = 0;
+-      else
+-              level = 1;
+-
+-      if (led_dat->active_low)
+-              level = !level;
++      switch (value) {
++      case LED_OFF:
++              level = led_dat->active_low ? 1 : 0;
++              break;
++      case LED_FULL:
++              level = led_dat->active_low ? 0 : 1;
++              break;
++      default:
++              level = value;
++              break;
++      }
+       /* Setting GPIOs with I2C/etc requires a task context, and we don't
+        * seem to have a reliable way to know if we're already in one; so
diff --git a/target/linux/adm5120/patches-2.6.30/310-adm5120_wdt.patch b/target/linux/adm5120/patches-2.6.30/310-adm5120_wdt.patch
new file mode 100644 (file)
index 0000000..bb5e613
--- /dev/null
@@ -0,0 +1,31 @@
+--- a/drivers/watchdog/Kconfig
++++ b/drivers/watchdog/Kconfig
+@@ -713,6 +713,18 @@ config RC32434_WDT
+         To compile this driver as a module, choose M here: the
+         module will be called rc32434_wdt.
++config ADM5120_WDT
++      tristate "Infineon ADM5120 SoC hardware watchdog"
++      depends on WATCHDOG && ADM5120
++      help
++        This is a driver for hardware watchdog integrated in Infineon
++        ADM5120 SoC. This watchdog simply watches your kernel to make sure
++        it doesn't freeze, and if it does, it reboots your computer after a
++        certain amount of time.
++
++        To compile this driver as a module, choose M here: the module will be
++        called adm5120_wdt.
++
+ config INDYDOG
+       tristate "Indy/I2 Hardware Watchdog"
+       depends on SGI_HAS_INDYDOG
+--- a/drivers/watchdog/Makefile
++++ b/drivers/watchdog/Makefile
+@@ -105,6 +105,7 @@ obj-$(CONFIG_WDT_RM9K_GPI) += rm9k_wdt.o
+ obj-$(CONFIG_SIBYTE_WDOG) += sb_wdog.o
+ obj-$(CONFIG_AR7_WDT) += ar7_wdt.o
+ obj-$(CONFIG_TXX9_WDT) += txx9wdt.o
++obj-$(CONFIG_ADM5120_WDT) += adm5120_wdt.o
+ # PARISC Architecture
diff --git a/target/linux/adm5120/patches-2.6.30/800-adm5120-remove-amba-bus-id.patch b/target/linux/adm5120/patches-2.6.30/800-adm5120-remove-amba-bus-id.patch
new file mode 100644 (file)
index 0000000..e2435fb
--- /dev/null
@@ -0,0 +1,18 @@
+--- a/arch/mips/adm5120/common/platform.c
++++ b/arch/mips/adm5120/common/platform.c
+@@ -190,7 +190,6 @@ struct amba_pl010_data adm5120_uart0_dat
+ struct amba_device adm5120_uart0_device = {
+       .dev            = {
+-              .bus_id = "APB:UART0",
+               .platform_data = &adm5120_uart0_data,
+       },
+       .res            = {
+@@ -208,7 +207,6 @@ struct amba_pl010_data adm5120_uart1_dat
+ struct amba_device adm5120_uart1_device = {
+       .dev            = {
+-              .bus_id = "APB:UART1",
+               .platform_data = &adm5120_uart1_data,
+       },
+       .res            = {
diff --git a/target/linux/adm5120/patches-2.6.30/801-adm5120-flash-remove-bus-id.patch b/target/linux/adm5120/patches-2.6.30/801-adm5120-flash-remove-bus-id.patch
new file mode 100644 (file)
index 0000000..d9e72e0
--- /dev/null
@@ -0,0 +1,11 @@
+--- a/drivers/mtd/maps/adm5120-flash.c
++++ b/drivers/mtd/maps/adm5120-flash.c
+@@ -233,7 +233,7 @@ static int adm5120_flash_initinfo(struct
+       struct flash_desc *fdesc;
+       u32 t = 0;
+-      map->name = dev->dev.bus_id;
++      map->name = dev_name(&dev->dev);
+       if (dev->id > 1) {
+               MAP_ERR(map, "invalid flash id\n");
diff --git a/target/linux/adm5120/patches-2.6.30/802-adm5120-switch-remove-redundant-napi-functions.patch b/target/linux/adm5120/patches-2.6.30/802-adm5120-switch-remove-redundant-napi-functions.patch
new file mode 100644 (file)
index 0000000..5c5873b
--- /dev/null
@@ -0,0 +1,20 @@
+--- a/drivers/net/adm5120sw.c
++++ b/drivers/net/adm5120sw.c
+@@ -517,7 +517,7 @@ static int adm5120_if_poll(struct napi_s
+       status = sw_int_status() & SWITCH_INTS_POLL;
+       if ((done < limit) && (!status)) {
+               SW_DBG("disable polling mode for %s\n", dev->name);
+-              netif_rx_complete(dev, napi);
++              napi_complete(napi);
+               sw_int_unmask(SWITCH_INTS_POLL);
+               return 0;
+       }
+@@ -548,7 +548,7 @@ static irqreturn_t adm5120_switch_irq(in
+               sw_dump_intr_mask("poll ints", status);
+               SW_DBG("enable polling mode for %s\n", dev->name);
+               sw_int_mask(SWITCH_INTS_POLL);
+-              netif_rx_schedule(dev, &priv->napi);
++              napi_schedule(&priv->napi);
+       }
+ #else
+       sw_int_ack(status);
diff --git a/target/linux/adm5120/router_be/config-2.6.30 b/target/linux/adm5120/router_be/config-2.6.30
new file mode 100644 (file)
index 0000000..a4a511f
--- /dev/null
@@ -0,0 +1,216 @@
+CONFIG_32BIT=y
+# CONFIG_64BIT is not set
+CONFIG_ADM5120=y
+CONFIG_ADM5120_ENET=y
+CONFIG_ADM5120_MACH_P_334WT=y
+CONFIG_ADM5120_MACH_P_335=y
+# CONFIG_ADM5120_OEM_CELLVISION is not set
+# CONFIG_ADM5120_OEM_COMPEX is not set
+# CONFIG_ADM5120_OEM_EDIMAX is not set
+# CONFIG_ADM5120_OEM_INFINEON is not set
+# CONFIG_ADM5120_OEM_MIKROTIK is not set
+# CONFIG_ADM5120_OEM_MOTOROLA is not set
+CONFIG_ADM5120_OEM_ZYXEL=y
+CONFIG_ADM5120_SOC_BGA=y
+CONFIG_ADM5120_WDT=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_ARCH_SUPPORTS_OPROFILE=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARM_AMBA=y
+CONFIG_BASE_SMALL=0
+# CONFIG_BCM47XX is not set
+# CONFIG_BINARY_PRINTF is not set
+CONFIG_BINFMT_MISC=m
+CONFIG_BITREVERSE=y
+# CONFIG_CAVIUM_OCTEON_REFERENCE_BOARD is not set
+# CONFIG_CAVIUM_OCTEON_SIMULATOR is not set
+CONFIG_CEVT_R4K=y
+CONFIG_CEVT_R4K_LIB=y
+CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,jffs2"
+CONFIG_CPU_BIG_ENDIAN=y
+# CONFIG_CPU_CAVIUM_OCTEON is not set
+CONFIG_CPU_HAS_LLSC=y
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_CPU_HAS_SYNC=y
+# CONFIG_CPU_LITTLE_ENDIAN is not set
+# CONFIG_CPU_LOONGSON2 is not set
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPS32_R1=y
+# CONFIG_CPU_MIPS32_R2 is not set
+# CONFIG_CPU_MIPS64_R1 is not set
+# CONFIG_CPU_MIPS64_R2 is not set
+CONFIG_CPU_MIPSR1=y
+# CONFIG_CPU_NEVADA is not set
+# CONFIG_CPU_R10000 is not set
+# CONFIG_CPU_R3000 is not set
+# CONFIG_CPU_R4300 is not set
+# CONFIG_CPU_R4X00 is not set
+# CONFIG_CPU_R5000 is not set
+# CONFIG_CPU_R5432 is not set
+# CONFIG_CPU_R5500 is not set
+# CONFIG_CPU_R6000 is not set
+# CONFIG_CPU_R8000 is not set
+# CONFIG_CPU_RM7000 is not set
+# CONFIG_CPU_RM9000 is not set
+# CONFIG_CPU_SB1 is not set
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+# CONFIG_CPU_TX39XX is not set
+# CONFIG_CPU_TX49XX is not set
+# CONFIG_CPU_VR41XX is not set
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_CSRC_R4K=y
+CONFIG_CSRC_R4K_LIB=y
+CONFIG_DECOMPRESS_LZMA=y
+CONFIG_DEVPORT=y
+# CONFIG_DM9000 is not set
+CONFIG_DMA_NEED_PCI_MAP_STATE=y
+CONFIG_DMA_NONCOHERENT=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_ELF_CORE=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_GENERIC_ACL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_HARDWARE_WATCHPOINTS=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HID=m
+CONFIG_HID_SUPPORT=y
+CONFIG_HW_HAS_PCI=y
+CONFIG_HW_RANDOM=y
+CONFIG_HZ=250
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_I2C is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+CONFIG_INPUT=m
+# CONFIG_INPUT_GPIO_BUTTONS is not set
+# CONFIG_INPUT_YEALINK is not set
+CONFIG_IRQ_CPU=y
+# CONFIG_ISDN is not set
+CONFIG_LEDS_GPIO=m
+CONFIG_LEDS_TRIGGER_ADM5120_SWITCH=m
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_LEMOTE_FULONG is not set
+# CONFIG_LIB80211 is not set
+# CONFIG_MACH_ALCHEMY is not set
+# CONFIG_MACH_DECSTATION is not set
+# CONFIG_MACH_JAZZ is not set
+# CONFIG_MACH_TX39XX is not set
+# CONFIG_MACH_TX49XX is not set
+# CONFIG_MACH_VR41XX is not set
+CONFIG_MII=m
+# CONFIG_MIKROTIK_RB532 is not set
+CONFIG_MIPS=y
+# CONFIG_MIPS_COBALT is not set
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+CONFIG_MIPS_MACHINE=y
+# CONFIG_MIPS_MALTA is not set
+CONFIG_MIPS_MT_DISABLED=y
+# CONFIG_MIPS_MT_SMP is not set
+# CONFIG_MIPS_MT_SMTC is not set
+# CONFIG_MIPS_SIM is not set
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MTD_ADM5120=y
+CONFIG_MTD_BLOCK2MTD=y
+CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_TRXSPLIT=y
+# CONFIG_NET_PCI is not set
+# CONFIG_NO_IOPORT is not set
+# CONFIG_NXP_STB220 is not set
+# CONFIG_NXP_STB225 is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_PCI=y
+CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_PCI_STUB is not set
+# CONFIG_PCSPKR_PLATFORM is not set
+# CONFIG_PMC_MSP is not set
+# CONFIG_PMC_YOSEMITE is not set
+# CONFIG_PNX8550_JBS is not set
+# CONFIG_PNX8550_STB810 is not set
+# CONFIG_PROBE_INITRD_HEADER is not set
+# CONFIG_PROM_EMU is not set
+CONFIG_SCHED_OMIT_FRAME_POINTER=y
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SERIAL_8250 is not set
+CONFIG_SERIAL_AMBA_PL010=y
+CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
+CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2
+CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS"
+# CONFIG_SERIAL_AMBA_PL011 is not set
+CONFIG_SERIO=y
+# CONFIG_SERIO_AMBAKMI is not set
+# CONFIG_SERIO_I8042 is not set
+# CONFIG_SERIO_LIBPS2 is not set
+# CONFIG_SERIO_PCIPS2 is not set
+# CONFIG_SERIO_RAW is not set
+CONFIG_SERIO_SERPORT=y
+# CONFIG_SGI_IP22 is not set
+# CONFIG_SGI_IP27 is not set
+# CONFIG_SGI_IP28 is not set
+# CONFIG_SGI_IP32 is not set
+# CONFIG_SIBYTE_BIGSUR is not set
+# CONFIG_SIBYTE_CARMEL is not set
+# CONFIG_SIBYTE_CRHINE is not set
+# CONFIG_SIBYTE_CRHONE is not set
+# CONFIG_SIBYTE_LITTLESUR is not set
+# CONFIG_SIBYTE_RHONE is not set
+# CONFIG_SIBYTE_SENTOSA is not set
+# CONFIG_SIBYTE_SWARM is not set
+# CONFIG_SLAB is not set
+# CONFIG_SLOW_WORK is not set
+CONFIG_SLUB=y
+CONFIG_SOFT_WATCHDOG=m
+CONFIG_SWAP_IO_SPACE=y
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_SYS_HAS_EARLY_PRINTK=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
+CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
+CONFIG_TICK_ONESHOT=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_TRACING_SUPPORT=y
+CONFIG_TRAD_SIGNALS=y
+CONFIG_USB=m
+CONFIG_USB_ADM5120_HCD=m
+CONFIG_USB_DEBUG=y
+CONFIG_USB_EHCI_HCD=m
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_HCD=m
+CONFIG_USB_SUPPORT=y
+# CONFIG_USB_UHCI_HCD is not set
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/adm5120/router_le/config-2.6.30 b/target/linux/adm5120/router_le/config-2.6.30
new file mode 100644 (file)
index 0000000..6d65d79
--- /dev/null
@@ -0,0 +1,263 @@
+CONFIG_32BIT=y
+# CONFIG_64BIT is not set
+CONFIG_ADM5120=y
+CONFIG_ADM5120_ENET=y
+CONFIG_ADM5120_MACH_BR_6104K=y
+CONFIG_ADM5120_MACH_BR_6104KP=y
+CONFIG_ADM5120_MACH_BR_61X4WG=y
+CONFIG_ADM5120_MACH_CAS_771=y
+CONFIG_ADM5120_MACH_EASY5120P_ATA=y
+CONFIG_ADM5120_MACH_EASY5120_RT=y
+CONFIG_ADM5120_MACH_EASY5120_WVOIP=y
+CONFIG_ADM5120_MACH_EASY83000=y
+CONFIG_ADM5120_MACH_NFS_101=y
+CONFIG_ADM5120_MACH_NP27G=y
+CONFIG_ADM5120_MACH_NP28G=y
+CONFIG_ADM5120_MACH_PMUGW=y
+CONFIG_ADM5120_MACH_RB_11X=y
+CONFIG_ADM5120_MACH_RB_133=y
+CONFIG_ADM5120_MACH_RB_133C=y
+CONFIG_ADM5120_MACH_RB_150=y
+CONFIG_ADM5120_MACH_RB_153=y
+CONFIG_ADM5120_MACH_RB_192=y
+CONFIG_ADM5120_MACH_WP54=y
+CONFIG_ADM5120_OEM_CELLVISION=y
+CONFIG_ADM5120_OEM_COMPEX=y
+CONFIG_ADM5120_OEM_EDIMAX=y
+CONFIG_ADM5120_OEM_INFINEON=y
+CONFIG_ADM5120_OEM_MIKROTIK=y
+CONFIG_ADM5120_OEM_MOTOROLA=y
+# CONFIG_ADM5120_OEM_ZYXEL is not set
+CONFIG_ADM5120_SOC_BGA=y
+CONFIG_ADM5120_WDT=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_ARCH_SUPPORTS_OPROFILE=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARM_AMBA=y
+CONFIG_ATA=m
+# CONFIG_ATA_NONSTANDARD is not set
+# CONFIG_ATA_PIIX is not set
+CONFIG_ATA_SFF=y
+CONFIG_BASE_SMALL=0
+# CONFIG_BCM47XX is not set
+# CONFIG_BINARY_PRINTF is not set
+CONFIG_BITREVERSE=y
+# CONFIG_CAVIUM_OCTEON_REFERENCE_BOARD is not set
+# CONFIG_CAVIUM_OCTEON_SIMULATOR is not set
+CONFIG_CEVT_R4K=y
+CONFIG_CEVT_R4K_LIB=y
+CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,yaffs2,jffs2"
+# CONFIG_CPU_BIG_ENDIAN is not set
+# CONFIG_CPU_CAVIUM_OCTEON is not set
+CONFIG_CPU_HAS_LLSC=y
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_CPU_HAS_SYNC=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+# CONFIG_CPU_LOONGSON2 is not set
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPS32_R1=y
+# CONFIG_CPU_MIPS32_R2 is not set
+# CONFIG_CPU_MIPS64_R1 is not set
+# CONFIG_CPU_MIPS64_R2 is not set
+CONFIG_CPU_MIPSR1=y
+# CONFIG_CPU_NEVADA is not set
+# CONFIG_CPU_R10000 is not set
+# CONFIG_CPU_R3000 is not set
+# CONFIG_CPU_R4300 is not set
+# CONFIG_CPU_R4X00 is not set
+# CONFIG_CPU_R5000 is not set
+# CONFIG_CPU_R5432 is not set
+# CONFIG_CPU_R5500 is not set
+# CONFIG_CPU_R6000 is not set
+# CONFIG_CPU_R8000 is not set
+# CONFIG_CPU_RM7000 is not set
+# CONFIG_CPU_RM9000 is not set
+# CONFIG_CPU_SB1 is not set
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+# CONFIG_CPU_TX39XX is not set
+# CONFIG_CPU_TX49XX is not set
+# CONFIG_CPU_VR41XX is not set
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=m
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_CSRC_R4K=y
+CONFIG_CSRC_R4K_LIB=y
+CONFIG_DECOMPRESS_LZMA=y
+CONFIG_DEVPORT=y
+# CONFIG_DM9000 is not set
+CONFIG_DMA_NEED_PCI_MAP_STATE=y
+CONFIG_DMA_NONCOHERENT=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_ELF_CORE=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_GENERIC_ACL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HAMRADIO is not set
+CONFIG_HARDWARE_WATCHPOINTS=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HID=m
+CONFIG_HID_SUPPORT=y
+CONFIG_HOSTAP=m
+CONFIG_HOSTAP_FIRMWARE=y
+CONFIG_HOSTAP_PCI=m
+CONFIG_HW_HAS_PCI=y
+CONFIG_HW_RANDOM=y
+CONFIG_HZ=250
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_I2C is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+CONFIG_INPUT=m
+# CONFIG_INPUT_GPIO_BUTTONS is not set
+# CONFIG_INPUT_YEALINK is not set
+CONFIG_IRQ_CPU=y
+# CONFIG_ISDN is not set
+CONFIG_KEXEC=y
+CONFIG_LEDS_GPIO=m
+CONFIG_LEDS_TRIGGER_ADM5120_SWITCH=m
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_LEMOTE_FULONG is not set
+CONFIG_LIB80211=m
+CONFIG_LIB80211_CRYPT_CCMP=m
+CONFIG_LIB80211_CRYPT_TKIP=m
+CONFIG_LIB80211_CRYPT_WEP=m
+# CONFIG_MACH_ALCHEMY is not set
+# CONFIG_MACH_DECSTATION is not set
+# CONFIG_MACH_JAZZ is not set
+# CONFIG_MACH_TX39XX is not set
+# CONFIG_MACH_TX49XX is not set
+# CONFIG_MACH_VR41XX is not set
+CONFIG_MII=m
+# CONFIG_MIKROTIK_RB532 is not set
+CONFIG_MIPS=y
+# CONFIG_MIPS_COBALT is not set
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+CONFIG_MIPS_MACHINE=y
+# CONFIG_MIPS_MALTA is not set
+CONFIG_MIPS_MT_DISABLED=y
+# CONFIG_MIPS_MT_SMP is not set
+# CONFIG_MIPS_MT_SMTC is not set
+# CONFIG_MIPS_SIM is not set
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MTD_ADM5120=y
+CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_MYLOADER_PARTS=y
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_CAFE is not set
+CONFIG_MTD_NAND_PLATFORM=y
+CONFIG_MTD_TRXSPLIT=y
+# CONFIG_NATSEMI is not set
+CONFIG_NO_HZ=y
+# CONFIG_NO_IOPORT is not set
+# CONFIG_NXP_STB220 is not set
+# CONFIG_NXP_STB225 is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_PATA_RB153_CF=m
+# CONFIG_PATA_SCH is not set
+CONFIG_PCI=y
+CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_PCI_STUB is not set
+# CONFIG_PCSPKR_PLATFORM is not set
+# CONFIG_PMC_MSP is not set
+# CONFIG_PMC_YOSEMITE is not set
+# CONFIG_PNX8550_JBS is not set
+# CONFIG_PNX8550_STB810 is not set
+# CONFIG_PROBE_INITRD_HEADER is not set
+# CONFIG_PROM_EMU is not set
+CONFIG_SCHED_OMIT_FRAME_POINTER=y
+CONFIG_SCSI=m
+# CONFIG_SERIAL_8250 is not set
+CONFIG_SERIAL_AMBA_PL010=y
+CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
+CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2
+CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS"
+# CONFIG_SERIAL_AMBA_PL011 is not set
+CONFIG_SERIO=y
+# CONFIG_SERIO_AMBAKMI is not set
+# CONFIG_SERIO_I8042 is not set
+# CONFIG_SERIO_LIBPS2 is not set
+# CONFIG_SERIO_PCIPS2 is not set
+# CONFIG_SERIO_RAW is not set
+CONFIG_SERIO_SERPORT=y
+# CONFIG_SGI_IP22 is not set
+# CONFIG_SGI_IP27 is not set
+# CONFIG_SGI_IP28 is not set
+# CONFIG_SGI_IP32 is not set
+# CONFIG_SIBYTE_BIGSUR is not set
+# CONFIG_SIBYTE_CARMEL is not set
+# CONFIG_SIBYTE_CRHINE is not set
+# CONFIG_SIBYTE_CRHONE is not set
+# CONFIG_SIBYTE_LITTLESUR is not set
+# CONFIG_SIBYTE_RHONE is not set
+# CONFIG_SIBYTE_SENTOSA is not set
+# CONFIG_SIBYTE_SWARM is not set
+# CONFIG_SLAB is not set
+# CONFIG_SLOW_WORK is not set
+CONFIG_SLUB=y
+CONFIG_SOFT_WATCHDOG=m
+# CONFIG_SWAP is not set
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_SYS_HAS_EARLY_PRINTK=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
+CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
+# CONFIG_TC35815 is not set
+CONFIG_TICK_ONESHOT=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_TRACING_SUPPORT=y
+CONFIG_TRAD_SIGNALS=y
+CONFIG_USB=m
+CONFIG_USB_ADM5120_HCD=m
+CONFIG_USB_EHCI_HCD=m
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_HCD=m
+CONFIG_USB_SUPPORT=y
+# CONFIG_USB_UHCI_HCD is not set
+CONFIG_VLAN_8021Q=m
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_YAFFS_9BYTE_TAGS=y
+# CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED is not set
+CONFIG_YAFFS_AUTO_YAFFS2=y
+# CONFIG_YAFFS_DISABLE_LAZY_LOAD is not set
+# CONFIG_YAFFS_DISABLE_WIDE_TNODES is not set
+CONFIG_YAFFS_FS=y
+CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y
+CONFIG_YAFFS_YAFFS1=y
+CONFIG_YAFFS_YAFFS2=y
+CONFIG_ZONE_DMA_FLAG=0