+++ /dev/null
-/*
- * (C) Copyright 2008
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8260.h>
-#include <ioports.h>
-
-#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
-#include <libfdt.h>
-#endif
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-const iop_conf_t iop_conf_tab[4][32] = {
-
- /* Port A */
- { /* conf ppar psor pdir podr pdat */
- /* PA31 */ { 0, 0, 0, 0, 0, 0 }, /* PA31 */
- /* PA30 */ { 0, 0, 0, 0, 0, 0 }, /* PA30 */
- /* PA29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 TXER */
- /* PA28 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 TXEN */
- /* PA27 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 RXDV */
- /* PA26 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 RXER */
- /* PA25 */ { 1, 0, 0, 1, 0, 0 }, /* ETH_PWRDWN */
- /* PA24 */ { 1, 0, 0, 1, 0, 1 }, /* ETH_RESET */
- /* PA23 */ { 0, 0, 0, 0, 0, 0 }, /* PA23 */
- /* PA22 */ { 0, 0, 0, 0, 0, 0 }, /* PA22 */
- /* PA21 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 TXD3 */
- /* PA20 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 TXD2 */
- /* PA19 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 TXD1 */
- /* PA18 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 TXD0 */
- /* PA17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 RXD0 */
- /* PA16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 RXD1 */
- /* PA15 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 RXD2 */
- /* PA14 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 RXD3 */
- /* PA13 */ { 0, 0, 0, 0, 0, 0 }, /* PA13 */
- /* PA12 */ { 1, 0, 0, 1, 0, 0 }, /* ETH_SLEEP */
- /* PA11 */ { 0, 0, 0, 0, 0, 0 }, /* PA11 */
- /* PA10 */ { 1, 0, 0, 1, 0, 0 }, /* MDIO */
- /* PA9 */ { 1, 0, 0, 1, 0, 0 }, /* MDC */
- /* PA8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC2 RxD */
- /* PA7 */ { 0, 0, 0, 0, 0, 0 }, /* PA7 */
- /* PA6 */ { 0, 0, 0, 0, 0, 0 }, /* PA6 */
- /* PA5 */ { 0, 0, 0, 0, 0, 0 }, /* PA5 */
- /* PA4 */ { 0, 0, 0, 0, 0, 0 }, /* PA4 */
- /* PA3 */ { 0, 0, 0, 0, 0, 0 }, /* PA3 */
- /* PA2 */ { 0, 0, 0, 0, 0, 0 }, /* PA2 */
- /* PA1 */ { 0, 0, 0, 0, 0, 0 }, /* PA1 */
- /* PA0 */ { 0, 0, 0, 0, 0, 0 } /* PA0 */
- },
-
- /* Port B */
- { /* conf ppar psor pdir podr pdat */
- /* PB31 */ { 0, 0, 0, 0, 0, 0 }, /* PB31 */
- /* PB30 */ { 0, 0, 0, 0, 0, 0 }, /* PB30 */
- /* PB29 */ { 0, 0, 0, 0, 0, 0 }, /* PB29 */
- /* PB28 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 TxD */
- /* PB27 */ { 0, 0, 0, 0, 0, 0 }, /* PB27 */
- /* PB26 */ { 0, 0, 0, 0, 0, 0 }, /* PB26 */
- /* PB25 */ { 0, 0, 0, 0, 0, 0 }, /* PB25 */
- /* PB24 */ { 0, 0, 0, 0, 0, 0 }, /* PB24 */
- /* PB23 */ { 0, 0, 0, 0, 0, 0 }, /* PB23 */
- /* PB22 */ { 0, 0, 0, 0, 0, 0 }, /* PB22 */
- /* PB21 */ { 0, 0, 0, 0, 0, 0 }, /* PB21 */
- /* PB20 */ { 0, 0, 0, 0, 0, 0 }, /* PB20 */
- /* PB19 */ { 0, 0, 0, 0, 0, 0 }, /* PB19 */
- /* PB18 */ { 0, 0, 0, 0, 0, 0 }, /* PB18 */
- /* PB17 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB16 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB15 */ { 1, 1, 0, 0, 0, 0 }, /* SCC2 RxD */
- /* PB14 */ { 1, 1, 0, 0, 0, 0 }, /* SCC3 RxD */
- /* PB13 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB12 */ { 1, 1, 1, 1, 0, 0 }, /* SCC2 TxD */
- /* PB11 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB10 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB9 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB8 */ { 1, 1, 1, 1, 0, 0 }, /* SCC3 TxD */
- /* PB7 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB6 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB5 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB4 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* non-existent */
- },
-
- /* Port C */
- { /* conf ppar psor pdir podr pdat */
- /* PC31 */ { 0, 0, 0, 0, 0, 0 }, /* PC31 */
- /* PC30 */ { 1, 1, 1, 1, 0, 0 }, /* Timer1 OUT */
- /* PC29 */ { 0, 0, 0, 0, 0, 0 }, /* PC29 */
- /* PC28 */ { 0, 0, 0, 0, 0, 0 }, /* PC28 */
- /* PC27 */ { 0, 0, 0, 0, 0, 0 }, /* PC27 */
- /* PC26 */ { 0, 0, 0, 0, 0, 0 }, /* PC26 */
- /* PC25 */ { 0, 0, 0, 0, 0, 0 }, /* PC25 */
- /* PC24 */ { 0, 0, 0, 0, 0, 0 }, /* PC24 */
- /* PC23 */ { 0, 0, 0, 0, 0, 0 }, /* PC23 */
- /* PC22 */ { 0, 0, 0, 0, 0, 0 }, /* PC22 */
- /* PC21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC RxCLK 11 */
- /* PC20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC TxCLK 12 */
- /* PC19 */ { 0, 0, 0, 0, 0, 0 }, /* PC19 */
- /* PC18 */ { 0, 0, 0, 0, 0, 0 }, /* PC18 */
- /* PC17 */ { 0, 0, 0, 0, 0, 0 }, /* PC17 */
- /* PC16 */ { 0, 0, 0, 0, 0, 0 }, /* PC16 */
- /* PC15 */ { 1, 1, 0, 1, 0, 0 }, /* SMC2 TxD */
- /* PC14 */ { 0, 0, 0, 0, 0, 0 }, /* PC14 */
- /* PC13 */ { 0, 0, 0, 0, 0, 0 }, /* PC13 */
- /* PC12 */ { 1, 0, 0, 1, 0, 0 }, /* TX OUTPUT SLEW1 */
- /* PC11 */ { 1, 0, 0, 1, 0, 0 }, /* TX OUTPUT SLEW0 */
- /* PC10 */ { 0, 0, 0, 0, 0, 0 }, /* PC10 */
- /* PC9 */ { 1, 0, 0, 1, 0, 1 }, /* SPA_TX_EN */
- /* PC8 */ { 0, 0, 0, 0, 0, 0 }, /* PC8 */
- /* PC7 */ { 0, 0, 0, 0, 0, 0 }, /* PC7 */
- /* PC6 */ { 0, 0, 0, 0, 0, 0 }, /* PC6 */
- /* PC5 */ { 0, 0, 0, 0, 0, 0 }, /* PC5 */
- /* PC4 */ { 0, 0, 0, 0, 0, 0 }, /* PC4 */
- /* PC3 */ { 0, 0, 0, 0, 0, 0 }, /* PC3 */
- /* PC2 */ { 0, 0, 0, 0, 0, 0 }, /* PC2 */
- /* PC1 */ { 0, 0, 0, 0, 0, 0 }, /* PC1 */
- /* PC0 */ { 0, 0, 0, 0, 0, 0 }, /* PC0 */
- },
-
- /* Port D */
- { /* conf ppar psor pdir podr pdat */
- /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 RxD */
- /* PD30 */ { 0, 0, 0, 0, 0, 0 }, /* PD30 */
- /* PD29 */ { 0, 0, 0, 0, 0, 0 }, /* PD29 */
- /* PD28 */ { 0, 0, 0, 0, 0, 0 }, /* PD28 */
- /* PD27 */ { 0, 0, 0, 0, 0, 0 }, /* PD27 */
- /* PD26 */ { 0, 0, 0, 0, 0, 0 }, /* PD26 */
- /* PD25 */ { 0, 0, 0, 0, 0, 0 }, /* PD25 */
- /* PD24 */ { 0, 0, 0, 0, 0, 0 }, /* PD24 */
- /* PD23 */ { 0, 0, 0, 0, 0, 0 }, /* PD23 */
- /* PD22 */ { 1, 1, 0, 0, 0, 0 }, /* SCC4: RXD */
- /* PD21 */ { 1, 1, 0, 1, 0, 0 }, /* SCC4: TXD */
- /* PD20 */ { 0, 0, 0, 0, 0, 0 }, /* PD18 */
- /* PD19 */ { 0, 0, 0, 0, 0, 0 }, /* PD19 */
- /* PD18 */ { 0, 0, 0, 0, 0, 0 }, /* PD18 */
- /* PD17 */ { 0, 0, 0, 0, 0, 0 }, /* PD17 */
- /* PD16 */ { 0, 0, 0, 0, 0, 0 }, /* PD16 */
-#if defined(CONFIG_HARD_I2C)
- /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */
- /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */
-#else
- /* PD15 */ { 1, 0, 0, 0, 1, 1 }, /* PD15 */
- /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* PD14 */
-#endif
- /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
- /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
- /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
- /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
- /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TxD */
- /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RxD */
- /* PD7 */ { 0, 0, 0, 0, 0, 0 }, /* PD7 */
- /* PD6 */ { 0, 0, 0, 0, 0, 0 }, /* PD6 */
- /* PD5 */ { 0, 0, 0, 0, 0, 0 }, /* PD5 */
- /* PD4 */ { 0, 0, 0, 0, 0, 0 }, /* PD4 */
- /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* non-existent */
- }
-};
-
-/* Try SDRAM initialization with P/LSDMR=sdmr and ORx=orx
- *
- * This routine performs standard 8260 initialization sequence
- * and calculates the available memory size. It may be called
- * several times to try different SDRAM configurations on both
- * 60x and local buses.
- */
-static long int try_init (volatile memctl8260_t * memctl, ulong sdmr,
- ulong orx, volatile uchar * base)
-{
- volatile uchar c = 0xff;
- volatile uint *sdmr_ptr;
- volatile uint *orx_ptr;
- ulong maxsize, size;
- int i;
-
- /* We must be able to test a location outsize the maximum legal size
- * to find out THAT we are outside; but this address still has to be
- * mapped by the controller. That means, that the initial mapping has
- * to be (at least) twice as large as the maximum expected size.
- */
- maxsize = (1 + (~orx | 0x7fff))/* / 2*/;
-
- sdmr_ptr = &memctl->memc_psdmr;
- orx_ptr = &memctl->memc_or1;
-
- *orx_ptr = orx;
-
- /*
- * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
- *
- * "At system reset, initialization software must set up the
- * programmable parameters in the memory controller banks registers
- * (ORx, BRx, P/LSDMR). After all memory parameters are configured,
- * system software should execute the following initialization sequence
- * for each SDRAM device.
- *
- * 1. Issue a PRECHARGE-ALL-BANKS command
- * 2. Issue eight CBR REFRESH commands
- * 3. Issue a MODE-SET command to initialize the mode register
- *
- * The initial commands are executed by setting P/LSDMR[OP] and
- * accessing the SDRAM with a single-byte transaction."
- *
- * The appropriate BRx/ORx registers have already been set when we
- * get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE.
- */
-
- *sdmr_ptr = sdmr | PSDMR_OP_PREA;
- *base = c;
-
- *sdmr_ptr = sdmr | PSDMR_OP_CBRR;
- for (i = 0; i < 8; i++)
- *base = c;
-
- *sdmr_ptr = sdmr | PSDMR_OP_MRW;
- *(base + CONFIG_SYS_MRS_OFFS) = c; /* setting MR on address lines */
-
- *sdmr_ptr = sdmr | PSDMR_OP_NORM | PSDMR_RFEN;
- *base = c;
-
- size = get_ram_size ((long *)base, maxsize);
- *orx_ptr = orx | ~(size - 1);
-
- return (size);
-}
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8260_t *memctl = &immap->im_memctl;
- long psize;
- long sizelittle, sizebig;
-
- memctl->memc_psrt = CONFIG_SYS_PSRT;
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
-
- /* 60x SDRAM setup:
- */
- sizelittle = try_init (memctl, CONFIG_SYS_PSDMR_LITTLE, CONFIG_SYS_OR1_LITTLE,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
- sizebig = try_init (memctl, CONFIG_SYS_PSDMR_BIG, CONFIG_SYS_OR1_BIG,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
- if (sizelittle < sizebig) {
- psize = sizebig;
- } else {
- psize = try_init (memctl, CONFIG_SYS_PSDMR_LITTLE, CONFIG_SYS_OR1_LITTLE,
- (uchar *) CONFIG_SYS_SDRAM_BASE);
- }
-
- icache_enable ();
-
- return (psize);
-}
-
-int checkboard (void)
-{
- puts ("Board: MUAS3001\n");
-
- return 0;
-}
-
-/*
- * Early board initalization.
- */
-int board_early_init_r (void)
-{
- return 0;
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * update "memory" property in the blob
- */
-void ft_blob_update (void *blob, bd_t *bd)
-{
- int ret, nodeoffset = 0;
- ulong flash_data[4] = {0};
- ulong speed = 0;
-
- /* update Flash addr, size */
- flash_data[2] = cpu_to_be32 (CONFIG_SYS_FLASH_BASE);
- flash_data[3] = cpu_to_be32 (CONFIG_SYS_FLASH_SIZE);
- nodeoffset = fdt_path_offset (blob, "/localbus");
- if (nodeoffset >= 0) {
- ret = fdt_setprop (blob, nodeoffset, "ranges", flash_data,
- sizeof (flash_data));
- if (ret < 0)
- printf ("ft_blob_update): cannot set /localbus/ranges "
- "property err:%s\n", fdt_strerror(ret));
- } else {
- /* memory node is required in dts */
- printf ("ft_blob_update(): cannot find /localbus node "
- "err:%s\n", fdt_strerror (nodeoffset));
- }
-
- /* baudrate */
- nodeoffset = fdt_path_offset (blob, "/soc/cpm/serial");
- if (nodeoffset >= 0) {
- speed = cpu_to_be32 (gd->baudrate);
- ret = fdt_setprop (blob, nodeoffset, "current-speed", &speed,
- sizeof (unsigned long));
- if (ret < 0)
- printf ("ft_blob_update): cannot set /soc/cpm/serial/current-speed "
- "property err:%s\n", fdt_strerror (ret));
- } else {
- /* baudrate is required in dts */
- printf ("ft_blob_update(): cannot find /soc/cpm/smc2/current-speed node "
- "err:%s\n", fdt_strerror (nodeoffset));
- }
-}
-
-int ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup (blob, bd);
- ft_blob_update (blob, bd);
-
- return 0;
-}
-#endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */
+++ /dev/null
-/*
- * (C) Copyright 2008
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MUAS3001 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFF000000
-
-#define CONFIG_CPM2 1 /* Has a CPM2 */
-
-/* Do boardspecific init */
-#define CONFIG_BOARD_EARLY_INIT_R 1
-
-/* enable Watchdog */
-#define CONFIG_WATCHDOG 1
-
-/*
- * Select serial console configuration
- *
- * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- */
-#define CONFIG_CONS_ON_SMC /* Console is on SMC */
-#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
-#undef CONFIG_CONS_NONE /* It's not on external UART */
-#if defined(CONFIG_MUAS_DEV_BOARD)
-#define CONFIG_CONS_INDEX 2 /* SMC2 is used for console */
-#else
-#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */
-#endif
-
-/*
- * Select ethernet configuration
- *
- * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
- * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
- * SCC, 1-3 for FCC)
- *
- * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
- * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
- * must be unset.
- */
-#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */
-#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */
-#undef CONFIG_ETHER_NONE /* No external Ethernet */
-
-#define CONFIG_ETHER_INDEX 1
-#define CONFIG_ETHER_ON_FCC1
-#define CONFIG_HAS_ETH0
-#define FCC_ENET
-
-/*
- * - Rx-CLK is CLK11
- * - Tx-CLK is CLK12
- */
-# define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12)
-# define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
-/*
- * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
- */
-# define CONFIG_SYS_CPMFCR_RAMTYPE (0)
-/* know on local Bus */
-/* define CONFIG_SYS_CPMFCR_RAMTYPE (CPMFCR_DTB | CPMFCR_BDB) */
-/*
- * - Enable Full Duplex in FSMR
- */
-# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
-
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
-# define CONFIG_SYS_PHY_ADDR 1
-/*
- * GPIO pins used for bit-banged MII communications
- */
-#define MDIO_PORT 0 /* Port A */
-#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
- (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
-#define MDC_DECLARE MDIO_DECLARE
-
-
-#define CONFIG_SYS_MDIO_PIN 0x00200000 /* PA10 */
-#define CONFIG_SYS_MDC_PIN 0x00400000 /* PA9 */
-
-#define MDIO_ACTIVE (iop->pdir |= CONFIG_SYS_MDIO_PIN)
-#define MDIO_TRISTATE (iop->pdir &= ~CONFIG_SYS_MDIO_PIN)
-#define MDIO_READ ((iop->pdat & CONFIG_SYS_MDIO_PIN) != 0)
-
-#define MDIO(bit) if(bit) iop->pdat |= CONFIG_SYS_MDIO_PIN; \
- else iop->pdat &= ~CONFIG_SYS_MDIO_PIN
-
-#define MDC(bit) if(bit) iop->pdat |= CONFIG_SYS_MDC_PIN; \
- else iop->pdat &= ~CONFIG_SYS_MDC_PIN
-
-#define MIIDELAY udelay(1)
-
-#ifndef CONFIG_8260_CLKIN
-#define CONFIG_8260_CLKIN 66000000 /* in Hz */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-
-/*
- * Default environment settings
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "u-boot_addr_r=100000\0" \
- "kernel_addr_r=200000\0" \
- "fdt_addr_r=400000\0" \
- "rootpath=/opt/eldk/ppc_6xx\0" \
- "u-boot=muas3001/u-boot.bin\0" \
- "bootfile=muas3001/uImage\0" \
- "fdt_file=muas3001/muas3001.dtb\0" \
- "ramdisk_file=uRamdisk\0" \
- "load=tftp ${u-boot_addr_r} ${u-boot}\0" \
- "update=prot off ff000000 ff03ffff; era ff000000 ff03ffff; " \
- "cp.b ${u-boot_addr_r} ff000000 ${filesize};" \
- "prot on ff000000 ff03ffff\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "addcons=setenv bootargs ${bootargs} console=ttyCPM0,${baudrate}\0" \
- "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:" \
- "${netmask}:${hostname}:${netdev}:off panic=1\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; run nfsargs addip addcons;" \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "net_self=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "tftp ${ramdisk_addr} ${ramdisk_file}; " \
- "run ramargs addip; " \
- "bootm ${kernel_addr_r} ${ramdisk_addr} ${fdt_addr_r}\0" \
- "ramdisk_addr=ff210000\0" \
- "kernel_addr=ff050000\0" \
- "fdt_addr=ff200000\0" \
- "flash_self=run ramargs addip addcons;bootm ${kernel_addr}" \
- " ${ramdisk_addr} ${fdt_addr}\0" \
- "updateramdisk=era ${ramdisk_addr} +1f0000;tftpb ${kernel_addr_r}" \
- " ${ramdisk_file};" \
- "cp.b ${kernel_addr_r} ${ramdisk_addr} ${filesize}\0" \
- "updatekernel=era ${kernel_addr} +1b0000;tftpb ${kernel_addr_r}" \
- " ${bootfile};" \
- "cp.b ${kernel_addr_r} ${kernel_addr} ${filesize}\0" \
- "updatefdt=era ${fdt_addr} +10000;tftpb ${fdt_addr_r} ${fdt_file};" \
- "cp.b ${fdt_addr_r} ${fdt_addr} ${filesize}\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFF000000
-#define CONFIG_SYS_FLASH_SIZE 32
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */
-
-#define CONFIG_ENV_IS_IN_FLASH
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#endif /* CONFIG_ENV_IS_IN_FLASH */
-
-/*
- * I2C Bus
- */
-#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-
-#define CONFIG_SYS_IMMR 0xF0000000
-#define CONFIG_SYS_DEFAULT_IMMR 0x0F010000
-
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/* Hard reset configuration word */
-#define CONFIG_SYS_HRCW_MASTER 0x0E028200 /* BPS=11 CIP=1 ISB=010 BMS=1 */
-
-/* No slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-#define CONFIG_SYS_HID0_INIT 0
-#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE)
-
-#define CONFIG_SYS_HID2 0
-
-#define CONFIG_SYS_SIUMCR 0x00200000
-#define CONFIG_SYS_BCR 0x004c0000
-#define CONFIG_SYS_SCCR 0x0
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 4-35
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
- SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
- SYPCR_SWRI|SYPCR_SWP)
-#endif /* CONFIG_WATCHDOG */
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register 5-5
- *-----------------------------------------------------------------------
- * turn on Checkstop Reset Enable
- */
-#define CONFIG_SYS_RMR 0
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control 4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration 13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR 0
-
-/*
- * Init Memory Controller:
- *
- * Bank Bus Machine PortSz Device
- * ---- --- ------- ------ ------
- * 0 60x GPCM 32 bit FLASH
- * 1 60x SDRAM 64 bit SDRAM
- * 4 60x GPCM 16 bit I/O Ctrl
- *
- */
-/* Bank 0 - FLASH
- */
-#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
- BRx_PS_32 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM (0xff000020)
-
-/* Bank 1 - 60x bus SDRAM
- */
-#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */
-
-#define CONFIG_SYS_MPTPR 0x2800
-
-/*-----------------------------------------------------------------------------
- * Address for Mode Register Set (MRS) command
- *-----------------------------------------------------------------------------
- */
-#define CONFIG_SYS_MRS_OFFS 0x00000110
-#define CONFIG_SYS_PSRT 0x13
-
-#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1_LITTLE
-
-/* SDRAM initialization values
-*/
-#define CONFIG_SYS_OR1_LITTLE ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI1_A7 |\
- ORxS_NUMR_12)
-
-#define CONFIG_SYS_PSDMR_LITTLE 0x004b36a3
-
-#define CONFIG_SYS_OR1_BIG ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI1_A4 |\
- ORxS_NUMR_12)
-
-#define CONFIG_SYS_PSDMR_BIG 0x014f36a3
-
-/* IO on CS4 initialization values
-*/
-#define CONFIG_SYS_IO_BASE 0xc0000000
-#define CONFIG_SYS_IO_SIZE 1
-
-#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_IO_BASE & BRx_BA_MSK) |\
- BRx_PS_16 | BRx_MS_GPCM_L | BRx_V)
-
-#define CONFIG_SYS_OR4_PRELIM (0xfff80020)
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-#define OF_TBCLK (bd->bi_busfreq / 4)
-#if defined(CONFIG_MUAS_DEV_BOARD)
-#define OF_STDOUT_PATH "/soc/cpm/serial@11a90"
-#else
-#define OF_STDOUT_PATH "/soc/cpm/serial@11a80"
-#endif
-
-#endif /* __CONFIG_H */
projects / oweals / u-boot.git / commitdiff