#define PLLC_PLLDIV8 0x170
#define PLLC_PLLDIV9 0x174
-/* SOC-specific pll info */
-#ifdef CONFIG_SOC_DM355
-#define ARM_PLLDIV PLLC_PLLDIV1
-#define DDR_PLLDIV PLLC_PLLDIV1
-#endif
-
-#ifdef CONFIG_SOC_DM644X
-#define ARM_PLLDIV PLLC_PLLDIV2
-#define DSP_PLLDIV PLLC_PLLDIV1
-#define DDR_PLLDIV PLLC_PLLDIV2
-#endif
-
-#ifdef CONFIG_SOC_DM646X
-#define DSP_PLLDIV PLLC_PLLDIV1
-#define ARM_PLLDIV PLLC_PLLDIV2
-#define DDR_PLLDIV PLLC_PLLDIV1
-#endif
-
-#ifdef CONFIG_SOC_DA8XX
unsigned int sysdiv[9] = {
PLLC_PLLDIV1, PLLC_PLLDIV2, PLLC_PLLDIV3, PLLC_PLLDIV4, PLLC_PLLDIV5,
PLLC_PLLDIV6, PLLC_PLLDIV7, PLLC_PLLDIV8, PLLC_PLLDIV9
return 0;
}
-#else /* CONFIG_SOC_DA8XX */
-
-static unsigned pll_div(volatile void *pllbase, unsigned offset)
-{
- u32 div;
-
- div = REG(pllbase + offset);
- return (div & BIT(15)) ? (1 + (div & 0x1f)) : 1;
-}
-
-static inline unsigned pll_prediv(volatile void *pllbase)
-{
-#ifdef CONFIG_SOC_DM355
- /* this register read seems to fail on pll0 */
- if (pllbase == (volatile void *)DAVINCI_PLL_CNTRL0_BASE)
- return 8;
- else
- return pll_div(pllbase, PLLC_PREDIV);
-#elif defined(CONFIG_SOC_DM365)
- return pll_div(pllbase, PLLC_PREDIV);
-#endif
- return 1;
-}
-
-static inline unsigned pll_postdiv(volatile void *pllbase)
-{
-#if defined(CONFIG_SOC_DM355) || defined(CONFIG_SOC_DM365)
- return pll_div(pllbase, PLLC_POSTDIV);
-#elif defined(CONFIG_SOC_DM6446)
- if (pllbase == (volatile void *)DAVINCI_PLL_CNTRL0_BASE)
- return pll_div(pllbase, PLLC_POSTDIV);
-#endif
- return 1;
-}
-
-static unsigned pll_sysclk_mhz(unsigned pll_addr, unsigned div)
-{
- volatile void *pllbase = (volatile void *) pll_addr;
-#ifdef CONFIG_SOC_DM646X
- unsigned base = CONFIG_REFCLK_FREQ / 1000;
-#else
- unsigned base = CONFIG_SYS_HZ_CLOCK / 1000;
-#endif
-
- /* the PLL might be bypassed */
- if (readl(pllbase + PLLC_PLLCTL) & BIT(0)) {
- base /= pll_prediv(pllbase);
-#if defined(CONFIG_SOC_DM365)
- base *= 2 * (readl(pllbase + PLLC_PLLM) & 0x0ff);
-#else
- base *= 1 + (REG(pllbase + PLLC_PLLM) & 0x0ff);
-#endif
- base /= pll_postdiv(pllbase);
- }
- return DIV_ROUND_UP(base, 1000 * pll_div(pllbase, div));
-}
-
-#ifdef DAVINCI_DM6467EVM
-unsigned int davinci_arm_clk_get()
-{
- return pll_sysclk_mhz(DAVINCI_PLL_CNTRL0_BASE, ARM_PLLDIV) * 1000000;
-}
-#endif
-
-#if defined(CONFIG_SOC_DM365)
-unsigned int davinci_clk_get(unsigned int div)
-{
- return pll_sysclk_mhz(DAVINCI_PLL_CNTRL0_BASE, div) * 1000000;
-}
-#endif
-
-int set_cpu_clk_info(void)
-{
- unsigned int pllbase = DAVINCI_PLL_CNTRL0_BASE;
-#if defined(CONFIG_SOC_DM365)
- pllbase = DAVINCI_PLL_CNTRL1_BASE;
-#endif
- gd->bd->bi_arm_freq = pll_sysclk_mhz(pllbase, ARM_PLLDIV);
-
-#ifdef DSP_PLLDIV
- gd->bd->bi_dsp_freq =
- pll_sysclk_mhz(DAVINCI_PLL_CNTRL0_BASE, DSP_PLLDIV);
-#else
- gd->bd->bi_dsp_freq = 0;
-#endif
-
- pllbase = DAVINCI_PLL_CNTRL1_BASE;
-#if defined(CONFIG_SOC_DM365)
- pllbase = DAVINCI_PLL_CNTRL0_BASE;
-#endif
- gd->bd->bi_ddr_freq = pll_sysclk_mhz(pllbase, DDR_PLLDIV) / 2;
-
- return 0;
-}
-
-#endif /* !CONFIG_SOC_DA8XX */
-
/*
* Initializes on-chip ethernet controllers.
* to override, implement board_eth_init()
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * SoC-specific code for tms320dm355 and similar chips
- *
- * Copyright (C) 2009 David Brownell
- */
-
-#include <common.h>
-#include <asm/arch/hardware.h>
-
-
-void davinci_enable_uart0(void)
-{
- lpsc_on(DAVINCI_LPSC_UART0);
-
- /* Bringup UART0 out of reset */
- REG(UART0_PWREMU_MGMT) = 0x00006001;
-}
-
-
-#ifdef CONFIG_SYS_I2C_DAVINCI
-void davinci_enable_i2c(void)
-{
- lpsc_on(DAVINCI_LPSC_I2C);
-
- /* Enable I2C pin Mux */
- REG(PINMUX3) |= (1 << 20) | (1 << 19);
-}
-#endif
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * SoC-specific code for tms320dm365 and similar chips
- */
-
-#include <common.h>
-#include <asm/arch/hardware.h>
-
-void davinci_enable_uart0(void)
-{
- lpsc_on(DAVINCI_LPSC_UART0);
-}
-
-#ifdef CONFIG_SYS_I2C_DAVINCI
-void davinci_enable_i2c(void)
-{
- lpsc_on(DAVINCI_LPSC_I2C);
-}
-#endif
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * SoC-specific lowlevel code for tms320dm365 and similar chips
- * Actually used for booting from NAND with nand_spl.
- *
- * Copyright (C) 2011
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- */
-#include <common.h>
-#include <nand.h>
-#include <ns16550.h>
-#include <post.h>
-#include <asm/ti-common/davinci_nand.h>
-#include <asm/arch/dm365_lowlevel.h>
-#include <asm/arch/hardware.h>
-
-void dm365_waitloop(unsigned long loopcnt)
-{
- unsigned long i;
-
- for (i = 0; i < loopcnt; i++)
- asm(" NOP");
-}
-
-int dm365_pll1_init(unsigned long pllmult, unsigned long prediv)
-{
- unsigned int clksrc = 0x0;
-
- /* Power up the PLL */
- clrbits_le32(&dv_pll0_regs->pllctl, PLLCTL_PLLPWRDN);
-
- clrbits_le32(&dv_pll0_regs->pllctl, PLLCTL_RES_9);
- setbits_le32(&dv_pll0_regs->pllctl,
- clksrc << PLLCTL_CLOCK_MODE_SHIFT);
-
- /*
- * Set PLLENSRC '0', PLL Enable(PLLEN) selection is controlled
- * through MMR
- */
- clrbits_le32(&dv_pll0_regs->pllctl, PLLCTL_PLLENSRC);
-
- /* Set PLLEN=0 => PLL BYPASS MODE */
- clrbits_le32(&dv_pll0_regs->pllctl, PLLCTL_PLLEN);
-
- dm365_waitloop(150);
-
- /* PLLRST=1(reset assert) */
- setbits_le32(&dv_pll0_regs->pllctl, PLLCTL_PLLRST);
-
- dm365_waitloop(300);
-
- /*Bring PLL out of Reset*/
- clrbits_le32(&dv_pll0_regs->pllctl, PLLCTL_PLLRST);
-
- /* Program the Multiper and Pre-Divider for PLL1 */
- writel(pllmult, &dv_pll0_regs->pllm);
- writel(prediv, &dv_pll0_regs->prediv);
-
- /* Assert TENABLE = 1, TENABLEDIV = 1, TINITZ = 1 */
- writel(PLLSECCTL_STOPMODE | PLLSECCTL_TENABLEDIV | PLLSECCTL_TENABLE |
- PLLSECCTL_TINITZ, &dv_pll0_regs->secctl);
- /* Assert TENABLE = 1, TENABLEDIV = 1, TINITZ = 0 */
- writel(PLLSECCTL_STOPMODE | PLLSECCTL_TENABLEDIV | PLLSECCTL_TENABLE,
- &dv_pll0_regs->secctl);
- /* Assert TENABLE = 0, TENABLEDIV = 0, TINITZ = 0 */
- writel(PLLSECCTL_STOPMODE, &dv_pll0_regs->secctl);
- /* Assert TENABLE = 0, TENABLEDIV = 0, TINITZ = 1 */
- writel(PLLSECCTL_STOPMODE | PLLSECCTL_TINITZ, &dv_pll0_regs->secctl);
-
- /* Program the PostDiv for PLL1 */
- writel(PLL_POSTDEN, &dv_pll0_regs->postdiv);
-
- /* Post divider setting for PLL1 */
- writel(CONFIG_SYS_DM36x_PLL1_PLLDIV1, &dv_pll0_regs->plldiv1);
- writel(CONFIG_SYS_DM36x_PLL1_PLLDIV2, &dv_pll0_regs->plldiv2);
- writel(CONFIG_SYS_DM36x_PLL1_PLLDIV3, &dv_pll0_regs->plldiv3);
- writel(CONFIG_SYS_DM36x_PLL1_PLLDIV4, &dv_pll0_regs->plldiv4);
- writel(CONFIG_SYS_DM36x_PLL1_PLLDIV5, &dv_pll0_regs->plldiv5);
- writel(CONFIG_SYS_DM36x_PLL1_PLLDIV6, &dv_pll0_regs->plldiv6);
- writel(CONFIG_SYS_DM36x_PLL1_PLLDIV7, &dv_pll0_regs->plldiv7);
- writel(CONFIG_SYS_DM36x_PLL1_PLLDIV8, &dv_pll0_regs->plldiv8);
- writel(CONFIG_SYS_DM36x_PLL1_PLLDIV9, &dv_pll0_regs->plldiv9);
-
- dm365_waitloop(300);
-
- /* Set the GOSET bit */
- writel(PLLCMD_GOSET, &dv_pll0_regs->pllcmd); /* Go */
-
- dm365_waitloop(300);
-
- /* Wait for PLL to LOCK */
- while (!((readl(&dv_sys_module_regs->pll0_config) & PLL0_LOCK)
- == PLL0_LOCK))
- ;
-
- /* Enable the PLL Bit of PLLCTL*/
- setbits_le32(&dv_pll0_regs->pllctl, PLLCTL_PLLEN);
-
- return 0;
-}
-
-int dm365_pll2_init(unsigned long pllm, unsigned long prediv)
-{
- unsigned int clksrc = 0x0;
-
- /* Power up the PLL*/
- clrbits_le32(&dv_pll1_regs->pllctl, PLLCTL_PLLPWRDN);
-
- /*
- * Select the Clock Mode as Onchip Oscilator or External Clock on
- * MXI pin
- * VDB has input on MXI pin
- */
- clrbits_le32(&dv_pll1_regs->pllctl, PLLCTL_RES_9);
- setbits_le32(&dv_pll1_regs->pllctl,
- clksrc << PLLCTL_CLOCK_MODE_SHIFT);
-
- /*
- * Set PLLENSRC '0', PLL Enable(PLLEN) selection is controlled
- * through MMR
- */
- clrbits_le32(&dv_pll1_regs->pllctl, PLLCTL_PLLENSRC);
-
- /* Set PLLEN=0 => PLL BYPASS MODE */
- clrbits_le32(&dv_pll1_regs->pllctl, PLLCTL_PLLEN);
-
- dm365_waitloop(50);
-
- /* PLLRST=1(reset assert) */
- setbits_le32(&dv_pll1_regs->pllctl, PLLCTL_PLLRST);
-
- dm365_waitloop(300);
-
- /* Bring PLL out of Reset */
- clrbits_le32(&dv_pll1_regs->pllctl, PLLCTL_PLLRST);
-
- /* Program the Multiper and Pre-Divider for PLL2 */
- writel(pllm, &dv_pll1_regs->pllm);
- writel(prediv, &dv_pll1_regs->prediv);
-
- writel(PLL_POSTDEN, &dv_pll1_regs->postdiv);
-
- /* Assert TENABLE = 1, TENABLEDIV = 1, TINITZ = 1 */
- writel(PLLSECCTL_STOPMODE | PLLSECCTL_TENABLEDIV | PLLSECCTL_TENABLE |
- PLLSECCTL_TINITZ, &dv_pll1_regs->secctl);
- /* Assert TENABLE = 1, TENABLEDIV = 1, TINITZ = 0 */
- writel(PLLSECCTL_STOPMODE | PLLSECCTL_TENABLEDIV | PLLSECCTL_TENABLE,
- &dv_pll1_regs->secctl);
- /* Assert TENABLE = 0, TENABLEDIV = 0, TINITZ = 0 */
- writel(PLLSECCTL_STOPMODE, &dv_pll1_regs->secctl);
- /* Assert TENABLE = 0, TENABLEDIV = 0, TINITZ = 1 */
- writel(PLLSECCTL_STOPMODE | PLLSECCTL_TINITZ, &dv_pll1_regs->secctl);
-
- /* Post divider setting for PLL2 */
- writel(CONFIG_SYS_DM36x_PLL2_PLLDIV1, &dv_pll1_regs->plldiv1);
- writel(CONFIG_SYS_DM36x_PLL2_PLLDIV2, &dv_pll1_regs->plldiv2);
- writel(CONFIG_SYS_DM36x_PLL2_PLLDIV3, &dv_pll1_regs->plldiv3);
- writel(CONFIG_SYS_DM36x_PLL2_PLLDIV4, &dv_pll1_regs->plldiv4);
- writel(CONFIG_SYS_DM36x_PLL2_PLLDIV5, &dv_pll1_regs->plldiv5);
-
- /* GoCmd for PostDivider to take effect */
- writel(PLLCMD_GOSET, &dv_pll1_regs->pllcmd);
-
- dm365_waitloop(150);
-
- /* Wait for PLL to LOCK */
- while (!((readl(&dv_sys_module_regs->pll1_config) & PLL1_LOCK)
- == PLL1_LOCK))
- ;
-
- dm365_waitloop(4100);
-
- /* Enable the PLL2 */
- setbits_le32(&dv_pll1_regs->pllctl, PLLCTL_PLLEN);
-
- /* do this after PLL's have been set up */
- writel(CONFIG_SYS_DM36x_PERI_CLK_CTRL,
- &dv_sys_module_regs->peri_clkctl);
-
- return 0;
-}
-
-int dm365_ddr_setup(void)
-{
- lpsc_on(DAVINCI_LPSC_DDR_EMIF);
- clrbits_le32(&dv_sys_module_regs->vtpiocr,
- VPTIO_IOPWRDN | VPTIO_CLRZ | VPTIO_LOCK | VPTIO_PWRDN);
-
- /* Set bit CLRZ (bit 13) */
- setbits_le32(&dv_sys_module_regs->vtpiocr, VPTIO_CLRZ);
-
- /* Check VTP READY Status */
- while (!(readl(&dv_sys_module_regs->vtpiocr) & VPTIO_RDY))
- ;
-
- /* Set bit VTP_IOPWRDWN bit 14 for DDR input buffers) */
- setbits_le32(&dv_sys_module_regs->vtpiocr, VPTIO_IOPWRDN);
-
- /* Set bit LOCK(bit7) */
- setbits_le32(&dv_sys_module_regs->vtpiocr, VPTIO_LOCK);
-
- /*
- * Powerdown VTP as it is locked (bit 6)
- * Set bit VTP_IOPWRDWN bit 14 for DDR input buffers)
- */
- setbits_le32(&dv_sys_module_regs->vtpiocr,
- VPTIO_IOPWRDN | VPTIO_PWRDN);
-
- /* Wait for calibration to complete */
- dm365_waitloop(150);
-
- /* Set the DDR2 to synreset, then enable it again */
- lpsc_syncreset(DAVINCI_LPSC_DDR_EMIF);
- lpsc_on(DAVINCI_LPSC_DDR_EMIF);
-
- writel(CONFIG_SYS_DM36x_DDR2_DDRPHYCR, &dv_ddr2_regs_ctrl->ddrphycr);
-
- /* Program SDRAM Bank Config Register */
- writel((CONFIG_SYS_DM36x_DDR2_SDBCR | DV_DDR_BOOTUNLOCK),
- &dv_ddr2_regs_ctrl->sdbcr);
- writel((CONFIG_SYS_DM36x_DDR2_SDBCR | DV_DDR_TIMUNLOCK),
- &dv_ddr2_regs_ctrl->sdbcr);
-
- /* Program SDRAM Timing Control Register1 */
- writel(CONFIG_SYS_DM36x_DDR2_SDTIMR, &dv_ddr2_regs_ctrl->sdtimr);
- /* Program SDRAM Timing Control Register2 */
- writel(CONFIG_SYS_DM36x_DDR2_SDTIMR2, &dv_ddr2_regs_ctrl->sdtimr2);
-
- writel(CONFIG_SYS_DM36x_DDR2_PBBPR, &dv_ddr2_regs_ctrl->pbbpr);
-
- writel(CONFIG_SYS_DM36x_DDR2_SDBCR, &dv_ddr2_regs_ctrl->sdbcr);
-
- /* Program SDRAM Refresh Control Register */
- writel(CONFIG_SYS_DM36x_DDR2_SDRCR, &dv_ddr2_regs_ctrl->sdrcr);
-
- lpsc_syncreset(DAVINCI_LPSC_DDR_EMIF);
- lpsc_on(DAVINCI_LPSC_DDR_EMIF);
-
- return 0;
-}
-
-static void dm365_vpss_sync_reset(void)
-{
- unsigned int PdNum = 0;
-
- /* VPSS_CLKMD 1:1 */
- setbits_le32(&dv_sys_module_regs->vpss_clkctl,
- VPSS_CLK_CTL_VPSS_CLKMD);
-
- /* LPSC SyncReset DDR Clock Enable */
- writel(((readl(&dv_psc_regs->mdctl[DAVINCI_LPSC_VPSSMASTER]) &
- ~PSC_MD_STATE_MSK) | PSC_SYNCRESET),
- &dv_psc_regs->mdctl[DAVINCI_LPSC_VPSSMASTER]);
-
- writel((1 << PdNum), &dv_psc_regs->ptcmd);
-
- while (!(((readl(&dv_psc_regs->ptstat) >> PdNum) & PSC_GOSTAT) == 0))
- ;
- while (!((readl(&dv_psc_regs->mdstat[DAVINCI_LPSC_VPSSMASTER]) &
- PSC_MD_STATE_MSK) == PSC_SYNCRESET))
- ;
-}
-
-static void dm365_por_reset(void)
-{
- struct davinci_timer *wdog =
- (struct davinci_timer *)DAVINCI_WDOG_BASE;
-
- if (readl(&dv_pll0_regs->rstype) &
- (PLL_RSTYPE_POR | PLL_RSTYPE_XWRST)) {
- dm365_vpss_sync_reset();
-
- writel(DV_TMPBUF_VAL, TMPBUF);
- setbits_le32(TMPSTATUS, FLAG_PORRST);
- writel(DV_WDT_ENABLE_SYS_RESET, &wdog->na1);
- writel(DV_WDT_TRIGGER_SYS_RESET, &wdog->na2);
-
- while (1);
- }
-}
-
-static void dm365_wdt_reset(void)
-{
- struct davinci_timer *wdog =
- (struct davinci_timer *)DAVINCI_WDOG_BASE;
-
- if (readl(TMPBUF) != DV_TMPBUF_VAL) {
- writel(DV_TMPBUF_VAL, TMPBUF);
- setbits_le32(TMPSTATUS, FLAG_PORRST);
- setbits_le32(TMPSTATUS, FLAG_FLGOFF);
-
- dm365_waitloop(100);
-
- dm365_vpss_sync_reset();
-
- writel(DV_WDT_ENABLE_SYS_RESET, &wdog->na1);
- writel(DV_WDT_TRIGGER_SYS_RESET, &wdog->na2);
-
- while (1);
- }
-}
-
-static void dm365_wdt_flag_on(void)
-{
- /* VPSS_CLKMD 1:2 */
- clrbits_le32(&dv_sys_module_regs->vpss_clkctl,
- VPSS_CLK_CTL_VPSS_CLKMD);
- writel(0, TMPBUF);
- setbits_le32(TMPSTATUS, FLAG_FLGON);
-}
-
-void dm365_psc_init(void)
-{
- unsigned char i = 0;
- unsigned char lpsc_start;
- unsigned char lpsc_end, lpscgroup, lpscmin, lpscmax;
- unsigned int PdNum = 0;
-
- lpscmin = 0;
- lpscmax = 2;
-
- for (lpscgroup = lpscmin; lpscgroup <= lpscmax; lpscgroup++) {
- if (lpscgroup == 0) {
- /* Enabling LPSC 3 to 28 SCR first */
- lpsc_start = DAVINCI_LPSC_VPSSMSTR;
- lpsc_end = DAVINCI_LPSC_TIMER1;
- } else if (lpscgroup == 1) { /* Skip locked LPSCs [29-37] */
- lpsc_start = DAVINCI_LPSC_CFG5;
- lpsc_end = DAVINCI_LPSC_VPSSMASTER;
- } else {
- lpsc_start = DAVINCI_LPSC_MJCP;
- lpsc_end = DAVINCI_LPSC_HDVICP;
- }
-
- /* NEXT=0x3, Enable LPSC's */
- for (i = lpsc_start; i <= lpsc_end; i++)
- setbits_le32(&dv_psc_regs->mdctl[i], PSC_ENABLE);
-
- /*
- * Program goctl to start transition sequence for LPSCs
- * CSL_PSC_0_REGS->PTCMD = (1<<PdNum); Kick off Power
- * Domain 0 Modules
- */
- writel((1 << PdNum), &dv_psc_regs->ptcmd);
-
- /*
- * Wait for GOSTAT = NO TRANSITION from PSC for Powerdomain 0
- */
- while (!(((readl(&dv_psc_regs->ptstat) >> PdNum) & PSC_GOSTAT)
- == 0))
- ;
-
- /* Wait for MODSTAT = ENABLE from LPSC's */
- for (i = lpsc_start; i <= lpsc_end; i++)
- while (!((readl(&dv_psc_regs->mdstat[i]) &
- PSC_MD_STATE_MSK) == PSC_ENABLE))
- ;
- }
-}
-
-static void dm365_emif_init(void)
-{
- writel(CONFIG_SYS_DM36x_AWCCR, &davinci_emif_regs->awccr);
- writel(CONFIG_SYS_DM36x_AB1CR, &davinci_emif_regs->ab1cr);
-
- setbits_le32(&davinci_emif_regs->nandfcr, DAVINCI_NANDFCR_CS2NAND);
-
- writel(CONFIG_SYS_DM36x_AB2CR, &davinci_emif_regs->ab2cr);
-
- return;
-}
-
-void dm365_pinmux_ctl(unsigned long offset, unsigned long mask,
- unsigned long value)
-{
- clrbits_le32(&dv_sys_module_regs->pinmux[offset], mask);
- setbits_le32(&dv_sys_module_regs->pinmux[offset], (mask & value));
-}
-
-__attribute__((weak))
-void board_gpio_init(void)
-{
- return;
-}
-
-#if defined(CONFIG_POST)
-int post_log(char *format, ...)
-{
- return 0;
-}
-#endif
-
-void dm36x_lowlevel_init(ulong bootflag)
-{
- struct davinci_uart_ctrl_regs *davinci_uart_ctrl_regs =
- (struct davinci_uart_ctrl_regs *)(CONFIG_SYS_NS16550_COM1 +
- DAVINCI_UART_CTRL_BASE);
-
- /* Mask all interrupts */
- writel(DV_AINTC_INTCTL_IDMODE, &dv_aintc_regs->intctl);
- writel(0x0, &dv_aintc_regs->eabase);
- writel(0x0, &dv_aintc_regs->eint0);
- writel(0x0, &dv_aintc_regs->eint1);
-
- /* Clear all interrupts */
- writel(0xffffffff, &dv_aintc_regs->fiq0);
- writel(0xffffffff, &dv_aintc_regs->fiq1);
- writel(0xffffffff, &dv_aintc_regs->irq0);
- writel(0xffffffff, &dv_aintc_regs->irq1);
-
- dm365_por_reset();
- dm365_wdt_reset();
-
- /* System PSC setup - enable all */
- dm365_psc_init();
-
- /* Setup Pinmux */
- dm365_pinmux_ctl(0, 0xFFFFFFFF, CONFIG_SYS_DM36x_PINMUX0);
- dm365_pinmux_ctl(1, 0xFFFFFFFF, CONFIG_SYS_DM36x_PINMUX1);
- dm365_pinmux_ctl(2, 0xFFFFFFFF, CONFIG_SYS_DM36x_PINMUX2);
- dm365_pinmux_ctl(3, 0xFFFFFFFF, CONFIG_SYS_DM36x_PINMUX3);
- dm365_pinmux_ctl(4, 0xFFFFFFFF, CONFIG_SYS_DM36x_PINMUX4);
-
- /* PLL setup */
- dm365_pll1_init(CONFIG_SYS_DM36x_PLL1_PLLM,
- CONFIG_SYS_DM36x_PLL1_PREDIV);
- dm365_pll2_init(CONFIG_SYS_DM36x_PLL2_PLLM,
- CONFIG_SYS_DM36x_PLL2_PREDIV);
-
- /* GPIO setup */
- board_gpio_init();
-
- NS16550_init((NS16550_t)(CONFIG_SYS_NS16550_COM1),
- CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE);
-
- /*
- * Fix Power and Emulation Management Register
- * see sprufh2.pdf page 38 Table 22
- */
- writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST |
- DAVINCI_UART_PWREMU_MGMT_UTRST),
- &davinci_uart_ctrl_regs->pwremu_mgmt);
-
- puts("ddr init\n");
- dm365_ddr_setup();
-
- puts("emif init\n");
- dm365_emif_init();
-
- dm365_wdt_flag_on();
-
-#if defined(CONFIG_POST)
- /*
- * Do memory tests, calls arch_memory_failure_handle()
- * if error detected.
- */
- memory_post_test(0);
-#endif
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * SoC-specific code for tms320dm644x chips
- *
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- * Copyright (C) 2008 Lyrtech <www.lyrtech.com>
- * Copyright (C) 2004 Texas Instruments.
- */
-
-#include <common.h>
-#include <asm/arch/hardware.h>
-
-
-#define PINMUX0_EMACEN (1 << 31)
-#define PINMUX0_AECS5 (1 << 11)
-#define PINMUX0_AECS4 (1 << 10)
-
-#define PINMUX1_I2C (1 << 7)
-#define PINMUX1_UART1 (1 << 1)
-#define PINMUX1_UART0 (1 << 0)
-
-
-void davinci_enable_uart0(void)
-{
- lpsc_on(DAVINCI_LPSC_UART0);
-
- /* Bringup UART0 out of reset */
- REG(UART0_PWREMU_MGMT) = 0x00006001;
-
- /* Enable UART0 MUX lines */
- REG(PINMUX1) |= PINMUX1_UART0;
-}
-
-#ifdef CONFIG_DRIVER_TI_EMAC
-void davinci_enable_emac(void)
-{
- lpsc_on(DAVINCI_LPSC_EMAC);
- lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
- lpsc_on(DAVINCI_LPSC_MDIO);
-
- /* Enable GIO3.3V cells used for EMAC */
- REG(VDD3P3V_PWDN) = 0;
-
- /* Enable EMAC. */
- REG(PINMUX0) |= PINMUX0_EMACEN;
-}
-#endif
-
-#ifdef CONFIG_SYS_I2C_DAVINCI
-void davinci_enable_i2c(void)
-{
- lpsc_on(DAVINCI_LPSC_I2C);
-
- /* Enable I2C pin Mux */
- REG(PINMUX1) |= PINMUX1_I2C;
-}
-#endif
-
-void davinci_errata_workarounds(void)
-{
- /*
- * Workaround for TMS320DM6446 errata 1.3.22:
- * PSC: PTSTAT Register Does Not Clear After Warm/Maximum Reset
- * Revision(s) Affected: 1.3 and earlier
- */
- REG(PSC_SILVER_BULLET) = 0;
-
- /*
- * Set the PR_OLD_COUNT bits in the Bus Burst Priority Register (PBBPR)
- * as suggested in TMS320DM6446 errata 2.1.2:
- *
- * On DM6446 Silicon Revision 2.1 and earlier, under certain conditions
- * low priority modules can occupy the bus and prevent high priority
- * modules like the VPSS from getting the required DDR2 throughput.
- * A hex value of 0x20 should provide a good ARM (cache enabled)
- * performance and still allow good utilization by the VPSS or other
- * modules.
- */
- REG(VBPR) = 0x20;
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * SoC-specific code for TMS320DM646x chips
- */
-
-#include <asm/arch/hardware.h>
-
-void davinci_enable_uart0(void)
-{
- lpsc_on(DAVINCI_DM646X_LPSC_UART0);
-}
-
-#ifdef CONFIG_DRIVER_TI_EMAC
-void davinci_enable_emac(void)
-{
- lpsc_on(DAVINCI_DM646X_LPSC_EMAC);
-}
-#endif
-
-#ifdef CONFIG_SYS_I2C_DAVINCI
-void davinci_enable_i2c(void)
-{
- lpsc_on(DAVINCI_DM646X_LPSC_I2C);
-}
-#endif
int davinci_configure_pin_mux(const struct pinmux_config *pins, int n_pins);
int davinci_configure_pin_mux_items(const struct pinmux_resource *item,
int n_items);
-#if defined(CONFIG_DRIVER_TI_EMAC) && defined(CONFIG_SOC_DA8XX)
+#if defined(CONFIG_DRIVER_TI_EMAC)
void davinci_emac_mii_mode_sel(int mode_sel);
#endif
-#if defined(CONFIG_SOC_DA8XX)
void irq_init(void);
int da8xx_configure_lpsc_items(const struct lpsc_resource *item,
const int n_items);
-#endif
#endif /* __MISC_H */
#include <asm/arch/hardware.h>
-#ifdef CONFIG_SOC_DM365
-#define EMAC_BASE_ADDR (0x01d07000)
-#define EMAC_WRAPPER_BASE_ADDR (0x01d0a000)
-#define EMAC_WRAPPER_RAM_ADDR (0x01d08000)
-#define EMAC_MDIO_BASE_ADDR (0x01d0b000)
-#define DAVINCI_EMAC_VERSION2
-#elif defined(CONFIG_SOC_DA8XX)
#define EMAC_BASE_ADDR DAVINCI_EMAC_CNTRL_REGS_BASE
#define EMAC_WRAPPER_BASE_ADDR DAVINCI_EMAC_WRAPPER_CNTRL_REGS_BASE
#define EMAC_WRAPPER_RAM_ADDR DAVINCI_EMAC_WRAPPER_RAM_BASE
#define EMAC_MDIO_BASE_ADDR DAVINCI_MDIO_CNTRL_REGS_BASE
#define DAVINCI_EMAC_VERSION2
-#else
-#define EMAC_BASE_ADDR (0x01c80000)
-#define EMAC_WRAPPER_BASE_ADDR (0x01c81000)
-#define EMAC_WRAPPER_RAM_ADDR (0x01c82000)
-#define EMAC_MDIO_BASE_ADDR (0x01c84000)
-#endif
-
-#ifdef CONFIG_SOC_DM646X
-#define DAVINCI_EMAC_VERSION2
-#define DAVINCI_EMAC_GIG_ENABLE
-#endif
-#ifdef CONFIG_SOC_DM646X
-/* MDIO module input frequency */
-#define EMAC_MDIO_BUS_FREQ 76500000
-/* MDIO clock output frequency */
-#define EMAC_MDIO_CLOCK_FREQ 2500000 /* 2.5 MHz */
-#elif defined(CONFIG_SOC_DM365)
-/* MDIO module input frequency */
-#define EMAC_MDIO_BUS_FREQ 121500000
-/* MDIO clock output frequency */
-#define EMAC_MDIO_CLOCK_FREQ 2200000 /* 2.2 MHz */
-#elif defined(CONFIG_SOC_DA8XX)
/* MDIO module input frequency */
#define EMAC_MDIO_BUS_FREQ clk_get(DAVINCI_MDIO_CLKID)
/* MDIO clock output frequency */
#define EMAC_MDIO_CLOCK_FREQ 2000000 /* 2.0 MHz */
-#else
-/* MDIO module input frequency */
-#define EMAC_MDIO_BUS_FREQ 99000000 /* PLL/6 - 99 MHz */
-/* MDIO clock output frequency */
-#define EMAC_MDIO_CLOCK_FREQ 2000000 /* 2.0 MHz */
-#endif
#endif /* _DM644X_EMAC_H_ */
#ifndef _GPIO_DEFS_H_
#define _GPIO_DEFS_H_
-#ifndef CONFIG_SOC_DA8XX
-#define DAVINCI_GPIO_BINTEN 0x01C67008
-#define DAVINCI_GPIO_BANK01 0x01C67010
-#define DAVINCI_GPIO_BANK23 0x01C67038
-#define DAVINCI_GPIO_BANK45 0x01C67060
-#define DAVINCI_GPIO_BANK67 0x01C67088
-
-#else /* CONFIG_SOC_DA8XX */
#define DAVINCI_GPIO_BINTEN 0x01E26008
#define DAVINCI_GPIO_BANK01 0x01E26010
#define DAVINCI_GPIO_BANK23 0x01E26038
#define DAVINCI_GPIO_BANK45 0x01E26060
#define DAVINCI_GPIO_BANK67 0x01E26088
#define DAVINCI_GPIO_BANK8 0x01E260B0
-#endif /* CONFIG_SOC_DA8XX */
#define davinci_gpio_bank01 ((struct davinci_gpio *)DAVINCI_GPIO_BANK01)
#define davinci_gpio_bank23 ((struct davinci_gpio *)DAVINCI_GPIO_BANK23)
#define gpio_status() gpio_info()
#endif
#define GPIO_NAME_SIZE 20
-#if defined(CONFIG_SOC_DM644X)
-/* GPIO0 to GPIO53, omit the V3.3 volts one */
-#define MAX_NUM_GPIOS 70
-#elif defined(CONFIG_SOC_DA8XX) && !defined(CONFIG_SOC_DA850)
+#if !defined(CONFIG_SOC_DA850)
#define MAX_NUM_GPIOS 128
#else
#define MAX_NUM_GPIOS 144
typedef volatile unsigned int * dv_reg_p;
#endif
-/*
- * Base register addresses
- *
- * NOTE: some of these DM6446-specific addresses DO NOT WORK
- * on other DaVinci chips. Double check them before you try
- * using the addresses ... or PSC module identifiers, etc.
- */
-#ifndef CONFIG_SOC_DA8XX
-
-#define DAVINCI_DMA_3PCC_BASE (0x01c00000)
-#define DAVINCI_DMA_3PTC0_BASE (0x01c10000)
-#define DAVINCI_DMA_3PTC1_BASE (0x01c10400)
-#define DAVINCI_UART0_BASE (0x01c20000)
-#define DAVINCI_UART1_BASE (0x01c20400)
-#define DAVINCI_TIMER3_BASE (0x01c20800)
-#define DAVINCI_I2C_BASE (0x01c21000)
-#define DAVINCI_TIMER0_BASE (0x01c21400)
-#define DAVINCI_TIMER1_BASE (0x01c21800)
-#define DAVINCI_WDOG_BASE (0x01c21c00)
-#define DAVINCI_PWM0_BASE (0x01c22000)
-#define DAVINCI_PWM1_BASE (0x01c22400)
-#define DAVINCI_PWM2_BASE (0x01c22800)
-#define DAVINCI_TIMER4_BASE (0x01c23800)
-#define DAVINCI_SYSTEM_MODULE_BASE (0x01c40000)
-#define DAVINCI_PLL_CNTRL0_BASE (0x01c40800)
-#define DAVINCI_PLL_CNTRL1_BASE (0x01c40c00)
-#define DAVINCI_PWR_SLEEP_CNTRL_BASE (0x01c41000)
-#define DAVINCI_ARM_INTC_BASE (0x01c48000)
-#define DAVINCI_USB_OTG_BASE (0x01c64000)
-#define DAVINCI_CFC_ATA_BASE (0x01c66000)
-#define DAVINCI_SPI_BASE (0x01c66800)
-#define DAVINCI_GPIO_BASE (0x01c67000)
-#define DAVINCI_VPSS_REGS_BASE (0x01c70000)
-#if !defined(CONFIG_SOC_DM646X)
-#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE (0x02000000)
-#define DAVINCI_ASYNC_EMIF_DATA_CE1_BASE (0x04000000)
-#define DAVINCI_ASYNC_EMIF_DATA_CE2_BASE (0x06000000)
-#define DAVINCI_ASYNC_EMIF_DATA_CE3_BASE (0x08000000)
-#endif
-#define DAVINCI_DDR_BASE (0x80000000)
-
-#ifdef CONFIG_SOC_DM644X
-#define DAVINCI_UART2_BASE 0x01c20800
-#define DAVINCI_UHPI_BASE 0x01c67800
-#define DAVINCI_EMAC_CNTRL_REGS_BASE 0x01c80000
-#define DAVINCI_EMAC_WRAPPER_CNTRL_REGS_BASE 0x01c81000
-#define DAVINCI_EMAC_WRAPPER_RAM_BASE 0x01c82000
-#define DAVINCI_MDIO_CNTRL_REGS_BASE 0x01c84000
-#define DAVINCI_IMCOP_BASE 0x01cc0000
-#define DAVINCI_ASYNC_EMIF_CNTRL_BASE 0x01e00000
-#define DAVINCI_VLYNQ_BASE 0x01e01000
-#define DAVINCI_ASP_BASE 0x01e02000
-#define DAVINCI_MMC_SD_BASE 0x01e10000
-#define DAVINCI_MS_BASE 0x01e20000
-#define DAVINCI_VLYNQ_REMOTE_BASE 0x0c000000
-
-#elif defined(CONFIG_SOC_DM355)
-#define DAVINCI_MMC_SD1_BASE 0x01e00000
-#define DAVINCI_ASP0_BASE 0x01e02000
-#define DAVINCI_ASP1_BASE 0x01e04000
-#define DAVINCI_UART2_BASE 0x01e06000
-#define DAVINCI_ASYNC_EMIF_CNTRL_BASE 0x01e10000
-#define DAVINCI_MMC_SD0_BASE 0x01e11000
-
-#elif defined(CONFIG_SOC_DM365)
-#define DAVINCI_MMC_SD1_BASE 0x01d00000
-#define DAVINCI_ASYNC_EMIF_CNTRL_BASE 0x01d10000
-#define DAVINCI_MMC_SD0_BASE 0x01d11000
-#define DAVINCI_DDR_EMIF_CTRL_BASE 0x20000000
-#define DAVINCI_SPI0_BASE 0x01c66000
-#define DAVINCI_SPI1_BASE 0x01c66800
-
-#elif defined(CONFIG_SOC_DM646X)
-#define DAVINCI_ASYNC_EMIF_CNTRL_BASE 0x20008000
-#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x42000000
-#define DAVINCI_ASYNC_EMIF_DATA_CE1_BASE 0x44000000
-#define DAVINCI_ASYNC_EMIF_DATA_CE2_BASE 0x46000000
-#define DAVINCI_ASYNC_EMIF_DATA_CE3_BASE 0x48000000
-
-#endif
-
-#else /* CONFIG_SOC_DA8XX */
-
#define DAVINCI_UART0_BASE 0x01c42000
#define DAVINCI_UART1_BASE 0x01d0c000
#define DAVINCI_UART2_BASE 0x01d0d000
#define GPIO_BANK6_REG_OPDATA_ADDR (DAVINCI_GPIO_BASE + 0x8c)
#define GPIO_BANK6_REG_SET_ADDR (DAVINCI_GPIO_BASE + 0x90)
#define GPIO_BANK6_REG_CLR_ADDR (DAVINCI_GPIO_BASE + 0x94)
-#endif /* CONFIG_SOC_DA8XX */
/* Power and Sleep Controller (PSC) Domains */
#define DAVINCI_GPSC_ARMDOMAIN 0
#define DAVINCI_GPSC_DSPDOMAIN 1
-#ifndef CONFIG_SOC_DA8XX
-
-#define DAVINCI_LPSC_VPSSMSTR 0
-#define DAVINCI_LPSC_VPSSSLV 1
-#define DAVINCI_LPSC_TPCC 2
-#define DAVINCI_LPSC_TPTC0 3
-#define DAVINCI_LPSC_TPTC1 4
-#define DAVINCI_LPSC_EMAC 5
-#define DAVINCI_LPSC_EMAC_WRAPPER 6
-#define DAVINCI_LPSC_MDIO 7
-#define DAVINCI_LPSC_IEEE1394 8
-#define DAVINCI_LPSC_USB 9
-#define DAVINCI_LPSC_ATA 10
-#define DAVINCI_LPSC_VLYNQ 11
-#define DAVINCI_LPSC_UHPI 12
-#define DAVINCI_LPSC_DDR_EMIF 13
-#define DAVINCI_LPSC_AEMIF 14
-#define DAVINCI_LPSC_MMC_SD 15
-#define DAVINCI_LPSC_MEMSTICK 16
-#define DAVINCI_LPSC_McBSP 17
-#define DAVINCI_LPSC_I2C 18
-#define DAVINCI_LPSC_UART0 19
-#define DAVINCI_LPSC_UART1 20
-#define DAVINCI_LPSC_UART2 21
-#define DAVINCI_LPSC_SPI 22
-#define DAVINCI_LPSC_PWM0 23
-#define DAVINCI_LPSC_PWM1 24
-#define DAVINCI_LPSC_PWM2 25
-#define DAVINCI_LPSC_GPIO 26
-#define DAVINCI_LPSC_TIMER0 27
-#define DAVINCI_LPSC_TIMER1 28
-#define DAVINCI_LPSC_TIMER2 29
-#define DAVINCI_LPSC_SYSTEM_SUBSYS 30
-#define DAVINCI_LPSC_ARM 31
-#define DAVINCI_LPSC_SCR2 32
-#define DAVINCI_LPSC_SCR3 33
-#define DAVINCI_LPSC_SCR4 34
-#define DAVINCI_LPSC_CROSSBAR 35
-#define DAVINCI_LPSC_CFG27 36
-#define DAVINCI_LPSC_CFG3 37
-#define DAVINCI_LPSC_CFG5 38
-#define DAVINCI_LPSC_GEM 39
-#define DAVINCI_LPSC_IMCOP 40
-#define DAVINCI_LPSC_VPSSMASTER 47
-#define DAVINCI_LPSC_MJCP 50
-#define DAVINCI_LPSC_HDVICP 51
-
-#define DAVINCI_DM646X_LPSC_EMAC 14
-#define DAVINCI_DM646X_LPSC_UART0 26
-#define DAVINCI_DM646X_LPSC_I2C 31
-#define DAVINCI_DM646X_LPSC_TIMER0 34
-
-#else /* CONFIG_SOC_DA8XX */
-
#define DAVINCI_LPSC_TPCC 0
#define DAVINCI_LPSC_TPTC0 1
#define DAVINCI_LPSC_TPTC1 2
#define DAVINCI_LPSC_SCR_F8 (DAVINCI_LPSC_PSC1_BASE + 29)
#define DAVINCI_LPSC_BR_F7 (DAVINCI_LPSC_PSC1_BASE + 30)
-#endif /* CONFIG_SOC_DA8XX */
-
#ifndef __ASSEMBLY__
void lpsc_on(unsigned int id);
void lpsc_syncreset(unsigned int id);
void davinci_enable_i2c(void);
void davinci_errata_workarounds(void);
-#ifndef CONFIG_SOC_DA8XX
-
-/* Some PSC defines */
-#define PSC_CHP_SHRTSW (0x01c40038)
-#define PSC_GBLCTL (0x01c41010)
-#define PSC_EPCPR (0x01c41070)
-#define PSC_EPCCR (0x01c41078)
-#define PSC_PTCMD (0x01c41120)
-#define PSC_PTSTAT (0x01c41128)
-#define PSC_PDSTAT (0x01c41200)
-#define PSC_PDSTAT1 (0x01c41204)
-#define PSC_PDCTL (0x01c41300)
-#define PSC_PDCTL1 (0x01c41304)
-
-#define PSC_MDCTL_BASE (0x01c41a00)
-#define PSC_MDSTAT_BASE (0x01c41800)
-
-#define VDD3P3V_PWDN (0x01c40048)
-#define UART0_PWREMU_MGMT (0x01c20030)
-
-#define PSC_SILVER_BULLET (0x01c41a20)
-
-#else /* CONFIG_SOC_DA8XX */
-
#define PSC_ENABLE 0x3
#define PSC_DISABLE 0x2
#define PSC_SYNCRESET 0x1
#define davinci_psc0_regs ((struct davinci_psc_regs *)DAVINCI_PSC0_BASE)
#define davinci_psc1_regs ((struct davinci_psc_regs *)DAVINCI_PSC1_BASE)
-#endif /* CONFIG_SOC_DA8XX */
-
#define PSC_MDSTAT_STATE 0x3f
#define PSC_MDCTL_NEXT 0x07
-#ifndef CONFIG_SOC_DA8XX
-
-/* Miscellania... */
-#define VBPR (0x20000020)
-
-/* NOTE: system control modules are *highly* chip-specific, both
- * as to register content (e.g. for muxing) and which registers exist.
- */
-#define PINMUX0 0x01c40000
-#define PINMUX1 0x01c40004
-#define PINMUX2 0x01c40008
-#define PINMUX3 0x01c4000c
-#define PINMUX4 0x01c40010
-
-struct davinci_uart_ctrl_regs {
- dv_reg revid1;
- dv_reg res;
- dv_reg pwremu_mgmt;
- dv_reg mdr;
-};
-
-#define DAVINCI_UART_CTRL_BASE 0x28
-
-/* UART PWREMU_MGMT definitions */
-#define DAVINCI_UART_PWREMU_MGMT_FREE (1 << 0)
-#define DAVINCI_UART_PWREMU_MGMT_URRST (1 << 13)
-#define DAVINCI_UART_PWREMU_MGMT_UTRST (1 << 14)
-
-#else /* CONFIG_SOC_DA8XX */
-
struct davinci_pllc_regs {
dv_reg revid;
dv_reg rsvd1[56];
DAVINCI_PLL1_SYSCLK2 : DAVINCI_PLL0_SYSCLK2;
}
-#endif /* CONFIG_SOC_DA8XX */
-
-#if defined(CONFIG_SOC_DM365)
-#include <asm/arch/aintc_defs.h>
-#include <asm/arch/ddr2_defs.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/pll_defs.h>
-#include <asm/arch/psc_defs.h>
-#include <asm/arch/syscfg_defs.h>
-#include <asm/arch/timer_defs.h>
-
-#define TMPBUF 0x00017ff8
-#define TMPSTATUS 0x00017ff0
-#define DV_TMPBUF_VAL 0x591b3ed7
-#define FLAG_PORRST 0x00000001
-#define FLAG_WDTRST 0x00000002
-#define FLAG_FLGON 0x00000004
-#define FLAG_FLGOFF 0x00000010
-
-#endif
#endif /* !__ASSEMBLY__ */
#endif /* __ASM_ARCH_HARDWARE_H */
#ifndef _I2C_DEFS_H_
#define _I2C_DEFS_H_
-#ifndef CONFIG_SOC_DA8XX
-#define I2C_BASE 0x01c21000
-#else
#define I2C_BASE 0x01c22000
-#endif
#endif
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2011
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- */
-#ifndef _DV_SYSCFG_DEFS_H_
-#define _DV_SYSCFG_DEFS_H_
-
-#ifndef CONFIG_SOC_DA8XX
-/* System Control Module register structure for DM365 */
-struct dv_sys_module_regs {
- unsigned int pinmux[5]; /* 0x00 */
- unsigned int bootcfg; /* 0x14 */
- unsigned int arm_intmux; /* 0x18 */
- unsigned int edma_evtmux; /* 0x1C */
- unsigned int ddr_slew; /* 0x20 */
- unsigned int clkout; /* 0x24 */
- unsigned int device_id; /* 0x28 */
- unsigned int vdac_config; /* 0x2C */
- unsigned int timer64_ctl; /* 0x30 */
- unsigned int usbbphy_ctl; /* 0x34 */
- unsigned int misc; /* 0x38 */
- unsigned int mstpri[2]; /* 0x3C */
- unsigned int vpss_clkctl; /* 0x44 */
- unsigned int peri_clkctl; /* 0x48 */
- unsigned int deepsleep; /* 0x4C */
- unsigned int dft_enable; /* 0x50 */
- unsigned int debounce[8]; /* 0x54 */
- unsigned int vtpiocr; /* 0x74 */
- unsigned int pupdctl0; /* 0x78 */
- unsigned int pupdctl1; /* 0x7C */
- unsigned int hdimcopbt; /* 0x80 */
- unsigned int pll0_config; /* 0x84 */
- unsigned int pll1_config; /* 0x88 */
-};
-
-#define VPTIO_RDY (1 << 15)
-#define VPTIO_IOPWRDN (1 << 14)
-#define VPTIO_CLRZ (1 << 13)
-#define VPTIO_LOCK (1 << 7)
-#define VPTIO_PWRDN (1 << 6)
-
-#define VPSS_CLK_CTL_VPSS_CLKMD (1 << 7)
-
-#define dv_sys_module_regs \
- ((struct dv_sys_module_regs *)DAVINCI_SYSTEM_MODULE_BASE)
-
-#endif /* !CONFIG_SOC_DA8XX */
-#endif /* _DV_SYSCFG_DEFS_H_ */
/*
* Set the mii mode as MII or RMII
*/
-#if defined(CONFIG_SOC_DA8XX)
void davinci_emac_mii_mode_sel(int mode_sel)
{
int val;
val |= (1 << 8);
writel(val, &davinci_syscfg_regs->cfgchip3);
}
-#endif
+
/*
* If there is no MAC address in the environment, then it will be initialized
* (silently) from the value in the EEPROM.
}
#endif /* CONFIG_DRIVER_TI_EMAC */
-#if defined(CONFIG_SOC_DA8XX)
void irq_init(void)
{
/*
return 0;
}
-#endif
static void lpsc_transition(unsigned int id, unsigned int state)
{
dv_reg_p mdstat, mdctl, ptstat, ptcmd;
-#ifdef CONFIG_SOC_DA8XX
struct davinci_psc_regs *psc_regs;
-#endif
-#ifndef CONFIG_SOC_DA8XX
- if (id >= DAVINCI_LPSC_GEM)
- return; /* Don't work on DSP Power Domain */
-
- mdstat = REG_P(PSC_MDSTAT_BASE + (id * 4));
- mdctl = REG_P(PSC_MDCTL_BASE + (id * 4));
- ptstat = REG_P(PSC_PTSTAT);
- ptcmd = REG_P(PSC_PTCMD);
-#else
if (id < DAVINCI_LPSC_PSC1_BASE) {
if (id >= PSC_PSC0_MODULE_ID_CNT)
return;
}
ptstat = &psc_regs->ptstat;
ptcmd = &psc_regs->ptcmd;
-#endif
while (readl(ptstat) & 0x01)
continue;
return; /* Already in that state */
writel((readl(mdctl) & ~PSC_MDCTL_NEXT) | state, mdctl);
-
- switch (id) {
-#ifdef CONFIG_SOC_DM644X
- /* Special treatment for some modules as for sprue14 p.7.4.2 */
- case DAVINCI_LPSC_VPSSSLV:
- case DAVINCI_LPSC_EMAC:
- case DAVINCI_LPSC_EMAC_WRAPPER:
- case DAVINCI_LPSC_MDIO:
- case DAVINCI_LPSC_USB:
- case DAVINCI_LPSC_ATA:
- case DAVINCI_LPSC_VLYNQ:
- case DAVINCI_LPSC_UHPI:
- case DAVINCI_LPSC_DDR_EMIF:
- case DAVINCI_LPSC_AEMIF:
- case DAVINCI_LPSC_MMC_SD:
- case DAVINCI_LPSC_MEMSTICK:
- case DAVINCI_LPSC_McBSP:
- case DAVINCI_LPSC_GPIO:
- writel(readl(mdctl) | 0x200, mdctl);
- break;
-#endif
- }
-
writel(0x01, ptcmd);
while (readl(ptstat) & 0x01)
{
lpsc_transition(id, 0x0);
}
-
-/* Not all DaVinci chips have a DSP power domain. */
-#ifdef CONFIG_SOC_DM644X
-
-/* If DSPLINK is used, we don't want U-Boot to power on the DSP. */
-#if !defined(CONFIG_SYS_USE_DSPLINK)
-void dsp_on(void)
-{
- int i;
-
- if (REG(PSC_PDSTAT1) & 0x1f)
- return; /* Already on */
-
- REG(PSC_GBLCTL) |= 0x01;
- REG(PSC_PDCTL1) |= 0x01;
- REG(PSC_PDCTL1) &= ~0x100;
- REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) |= 0x03;
- REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) &= 0xfffffeff;
- REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) |= 0x03;
- REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) &= 0xfffffeff;
- REG(PSC_PTCMD) = 0x02;
-
- for (i = 0; i < 100; i++) {
- if (REG(PSC_EPCPR) & 0x02)
- break;
- }
-
- REG(PSC_CHP_SHRTSW) = 0x01;
- REG(PSC_PDCTL1) |= 0x100;
- REG(PSC_EPCCR) = 0x02;
-
- for (i = 0; i < 100; i++) {
- if (!(REG(PSC_PTSTAT) & 0x02))
- break;
- }
-
- REG(PSC_GBLCTL) &= ~0x1f;
-}
-#endif /* CONFIG_SYS_USE_DSPLINK */
-
-#endif /* have a DSP */
void spl_board_init(void)
{
-#ifdef CONFIG_SOC_DM365
- dm36x_lowlevel_init(0);
-#endif
-#ifdef CONFIG_SOC_DA8XX
arch_cpu_init();
-#endif
preloader_console_init();
}
projects / oweals / u-boot.git / commitdiff