udoo_neo: Remove USDHC3 support
authorBreno Lima <breno.lima@nxp.com>
Thu, 1 Dec 2016 18:37:36 +0000 (16:37 -0200)
committerStefano Babic <sbabic@denx.de>
Fri, 16 Dec 2016 09:09:24 +0000 (10:09 +0100)
It's not necessary to support USDHC3 in U-Boot as it's being used for
the WLAN.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
board/udoo/neo/neo.c
include/configs/udoo_neo.h

index 7f17469d9af20faa96d2a551dd9fbd63dea81729..efe86055408ddc41a8643a778b19e2fa4c76d62e 100644 (file)
@@ -81,16 +81,6 @@ static iomux_v3_cfg_t const board_recognition_pads[] = {
        MX6_PAD_NAND_ALE__GPIO4_IO_0 | BOARD_DETECT_PAD_CFG,
 };
 
-static iomux_v3_cfg_t const usdhc3_pads[] = {
-    /* Configured for WLAN */
-       MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-};
-
 static iomux_v3_cfg_t const wdog_b_pad = {
        MX6_PAD_GPIO1_IO13__GPIO1_IO_13 | MUX_PAD_CTRL(WDOG_PAD_CTRL),
 };
@@ -171,91 +161,19 @@ static struct fsl_esdhc_cfg usdhc_cfg[2] = {
 
 int board_mmc_getcd(struct mmc *mmc)
 {
-       struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-       int ret = 0;
-
-       switch (cfg->esdhc_base) {
-       case USDHC2_BASE_ADDR:
-               ret = !gpio_get_value(USDHC2_CD_GPIO);
-               break;
-       }
-
-       return ret;
+       return !gpio_get_value(USDHC2_CD_GPIO);
 }
 
 int board_mmc_init(bd_t *bis)
 {
-#ifndef CONFIG_SPL_BUILD
-       int i, ret;
-
-       /*
-        * According to the board_mmc_init() the following map is done:
-        * (U-boot device node)    (Physical Port)
-        * mmc0                    USDHC2
-        */
-       for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
-               switch (i) {
-               case 0:
-                       imx_iomux_v3_setup_multiple_pads(
-                               usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
-                       usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-                       gpio_direction_input(USDHC2_CD_GPIO);
-                       gpio_direction_output(USDHC2_PWR_GPIO, 1);
-                       break;
-               case 1:
-                       imx_iomux_v3_setup_multiple_pads(
-                               usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
-                       usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
-                       break;
-               default:
-                       printf("Warning: you configured more USDHC controllers\
-                               (%d) than supported by the board\n", i + 1);
-                       return -EINVAL;
-                       }
-
-                       ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
-                       if (ret) {
-                               printf("Warning:\
-                                       failed to initialize mmc dev %d\n", i);
-                               return ret;
-                       }
-       }
-
-       return 0;
-#else
-       struct src *src_regs = (struct src *)SRC_BASE_ADDR;
-       u32 val;
-       u32 port;
-
-       val = readl(&src_regs->sbmr1);
-
-       if ((val & 0xc0) != 0x40) {
-               printf("Not boot from USDHC!\n");
-               return -EINVAL;
-       }
-
-       port = (val >> 11) & 0x3;
-       printf("port %d\n", port);
-       switch (port) {
-       case 1:
-               imx_iomux_v3_setup_multiple_pads(
-                       usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
-               usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-               usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
-               gpio_direction_input(USDHC2_CD_GPIO);
-               gpio_direction_output(USDHC2_PWR_GPIO, 1);
-               break;
-       case 2:
-               imx_iomux_v3_setup_multiple_pads(
-                       usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
-               usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
-               usdhc_cfg[1].esdhc_base = USDHC3_BASE_ADDR;
-               break;
-       }
+       imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+       usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+       usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
+       gpio_direction_input(USDHC2_CD_GPIO);
+       gpio_direction_output(USDHC2_PWR_GPIO, 1);
 
        gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
        return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-#endif
 }
 
 char *board_string(void)
index 81e04810eb5754a37f568ef4e5b872ad78b3ec45..cf75186b5274bbf54ade67a725f060527ed1d849 100644 (file)
@@ -27,7 +27,6 @@
 
 /* Command definition */
 #define CONFIG_MXC_UART_BASE           UART1_BASE
-#define CONFIG_SYS_FSL_USDHC_NUM       2
 #define CONFIG_SYS_MMC_ENV_DEV         0  /*USDHC2*/
 
 /* Linux only */