obj-y += wrap_pll_config_s10.o
endif
ifdef CONFIG_SPL_BUILD
-obj-y += spl.o
ifdef CONFIG_TARGET_SOCFPGA_GEN5
+obj-y += spl_gen5.o
obj-y += freeze_controller.o
obj-y += wrap_iocsr_config.o
obj-y += wrap_pinmux_config.o
obj-y += wrap_sdram_config.o
endif
+ifdef CONFIG_TARGET_SOCFPGA_ARRIA10
+obj-y += spl_a10.o
+endif
endif
ifdef CONFIG_TARGET_SOCFPGA_GEN5
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2012 Altera Corporation <www.altera.com>
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/pl310.h>
-#include <asm/u-boot.h>
-#include <asm/utils.h>
-#include <image.h>
-#include <asm/arch/reset_manager.h>
-#include <spl.h>
-#include <asm/arch/system_manager.h>
-#include <asm/arch/freeze_controller.h>
-#include <asm/arch/clock_manager.h>
-#include <asm/arch/misc.h>
-#include <asm/arch/scan_manager.h>
-#include <asm/arch/sdram.h>
-#include <asm/arch/scu.h>
-#include <asm/arch/nic301.h>
-#include <asm/sections.h>
-#include <fdtdec.h>
-#include <watchdog.h>
-#if defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
-#include <asm/arch/pinmux.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
-static struct pl310_regs *const pl310 =
- (struct pl310_regs *)CONFIG_SYS_PL310_BASE;
-static struct scu_registers *scu_regs =
- (struct scu_registers *)SOCFPGA_MPUSCU_ADDRESS;
-static struct nic301_registers *nic301_regs =
- (struct nic301_registers *)SOCFPGA_L3REGS_ADDRESS;
-#endif
-
-static const struct socfpga_system_manager *sysmgr_regs =
- (struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
-
-u32 spl_boot_device(void)
-{
- const u32 bsel = readl(&sysmgr_regs->bootinfo);
-
- switch (SYSMGR_GET_BOOTINFO_BSEL(bsel)) {
- case 0x1: /* FPGA (HPS2FPGA Bridge) */
- return BOOT_DEVICE_RAM;
- case 0x2: /* NAND Flash (1.8V) */
- case 0x3: /* NAND Flash (3.0V) */
- socfpga_per_reset(SOCFPGA_RESET(NAND), 0);
- return BOOT_DEVICE_NAND;
- case 0x4: /* SD/MMC External Transceiver (1.8V) */
- case 0x5: /* SD/MMC Internal Transceiver (3.0V) */
- socfpga_per_reset(SOCFPGA_RESET(SDMMC), 0);
- socfpga_per_reset(SOCFPGA_RESET(DMA), 0);
- return BOOT_DEVICE_MMC1;
- case 0x6: /* QSPI Flash (1.8V) */
- case 0x7: /* QSPI Flash (3.0V) */
- socfpga_per_reset(SOCFPGA_RESET(QSPI), 0);
- return BOOT_DEVICE_SPI;
- default:
- printf("Invalid boot device (bsel=%08x)!\n", bsel);
- hang();
- }
-}
-
-#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
-static void socfpga_nic301_slave_ns(void)
-{
- writel(0x1, &nic301_regs->lwhps2fpgaregs);
- writel(0x1, &nic301_regs->hps2fpgaregs);
- writel(0x1, &nic301_regs->acp);
- writel(0x1, &nic301_regs->rom);
- writel(0x1, &nic301_regs->ocram);
- writel(0x1, &nic301_regs->sdrdata);
-}
-
-void board_init_f(ulong dummy)
-{
- const struct cm_config *cm_default_cfg = cm_get_default_config();
- unsigned long sdram_size;
- unsigned long reg;
-
- /*
- * First C code to run. Clear fake OCRAM ECC first as SBE
- * and DBE might triggered during power on
- */
- reg = readl(&sysmgr_regs->eccgrp_ocram);
- if (reg & SYSMGR_ECC_OCRAM_SERR)
- writel(SYSMGR_ECC_OCRAM_SERR | SYSMGR_ECC_OCRAM_EN,
- &sysmgr_regs->eccgrp_ocram);
- if (reg & SYSMGR_ECC_OCRAM_DERR)
- writel(SYSMGR_ECC_OCRAM_DERR | SYSMGR_ECC_OCRAM_EN,
- &sysmgr_regs->eccgrp_ocram);
-
- memset(__bss_start, 0, __bss_end - __bss_start);
-
- socfpga_nic301_slave_ns();
-
- /* Configure ARM MPU SNSAC register. */
- setbits_le32(&scu_regs->sacr, 0xfff);
-
- /* Remap SDRAM to 0x0 */
- writel(0x1, &nic301_regs->remap); /* remap.mpuzero */
- writel(0x1, &pl310->pl310_addr_filter_start);
-
- debug("Freezing all I/O banks\n");
- /* freeze all IO banks */
- sys_mgr_frzctrl_freeze_req();
-
- /* Put everything into reset but L4WD0. */
- socfpga_per_reset_all();
- /* Put FPGA bridges into reset too. */
- socfpga_bridges_reset(1);
-
- socfpga_per_reset(SOCFPGA_RESET(SDR), 0);
- socfpga_per_reset(SOCFPGA_RESET(UART0), 0);
- socfpga_per_reset(SOCFPGA_RESET(OSC1TIMER0), 0);
-
- timer_init();
-
- debug("Reconfigure Clock Manager\n");
- /* reconfigure the PLLs */
- if (cm_basic_init(cm_default_cfg))
- hang();
-
- /* Enable bootrom to configure IOs. */
- sysmgr_config_warmrstcfgio(1);
-
- /* configure the IOCSR / IO buffer settings */
- if (scan_mgr_configure_iocsr())
- hang();
-
- sysmgr_config_warmrstcfgio(0);
-
- /* configure the pin muxing through system manager */
- sysmgr_config_warmrstcfgio(1);
- sysmgr_pinmux_init();
- sysmgr_config_warmrstcfgio(0);
-
- /* De-assert reset for peripherals and bridges based on handoff */
- reset_deassert_peripherals_handoff();
- socfpga_bridges_reset(0);
-
- debug("Unfreezing/Thaw all I/O banks\n");
- /* unfreeze / thaw all IO banks */
- sys_mgr_frzctrl_thaw_req();
-
- /* enable console uart printing */
- preloader_console_init();
-
- if (sdram_mmr_init_full(0xffffffff) != 0) {
- puts("SDRAM init failed.\n");
- hang();
- }
-
- debug("SDRAM: Calibrating PHY\n");
- /* SDRAM calibration */
- if (sdram_calibration_full() == 0) {
- puts("SDRAM calibration failed.\n");
- hang();
- }
-
- sdram_size = sdram_calculate_size();
- debug("SDRAM: %ld MiB\n", sdram_size >> 20);
-
- /* Sanity check ensure correct SDRAM size specified */
- if (get_ram_size(0, sdram_size) != sdram_size) {
- puts("SDRAM size check failed!\n");
- hang();
- }
-
- socfpga_bridges_reset(1);
-
- /* Configure simple malloc base pointer into RAM. */
- gd->malloc_base = CONFIG_SYS_TEXT_BASE + (1024 * 1024);
-}
-#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
-void spl_board_init(void)
-{
- /* configuring the clock based on handoff */
- cm_basic_init(gd->fdt_blob);
- WATCHDOG_RESET();
-
- config_dedicated_pins(gd->fdt_blob);
- WATCHDOG_RESET();
-
- /* Release UART from reset */
- socfpga_reset_uart(0);
-
- /* enable console uart printing */
- preloader_console_init();
-
- WATCHDOG_RESET();
-
- /* Add device descriptor to FPGA device table */
- socfpga_fpga_add();
-}
-
-void board_init_f(ulong dummy)
-{
- /*
- * Configure Clock Manager to use intosc clock instead external osc to
- * ensure success watchdog operation. We do it as early as possible.
- */
- cm_use_intosc();
-
- socfpga_watchdog_disable();
-
- arch_early_init_r();
-
-#ifdef CONFIG_HW_WATCHDOG
- /* release osc1 watchdog timer 0 from reset */
- socfpga_reset_deassert_osc1wd0();
-
- /* reconfigure and enable the watchdog */
- hw_watchdog_init();
- WATCHDOG_RESET();
-#endif /* CONFIG_HW_WATCHDOG */
-}
-#endif
--- /dev/null
+/*
+ * Copyright (C) 2012 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/pl310.h>
+#include <asm/u-boot.h>
+#include <asm/utils.h>
+#include <image.h>
+#include <asm/arch/reset_manager.h>
+#include <spl.h>
+#include <asm/arch/system_manager.h>
+#include <asm/arch/freeze_controller.h>
+#include <asm/arch/clock_manager.h>
+#include <asm/arch/scan_manager.h>
+#include <asm/arch/sdram.h>
+#include <asm/arch/scu.h>
+#include <asm/arch/nic301.h>
+#include <asm/sections.h>
+#include <fdtdec.h>
+#include <watchdog.h>
+#include <asm/arch/pinmux.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static const struct socfpga_system_manager *sysmgr_regs =
+ (struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
+
+u32 spl_boot_device(void)
+{
+ const u32 bsel = readl(&sysmgr_regs->bootinfo);
+
+ switch (SYSMGR_GET_BOOTINFO_BSEL(bsel)) {
+ case 0x1: /* FPGA (HPS2FPGA Bridge) */
+ return BOOT_DEVICE_RAM;
+ case 0x2: /* NAND Flash (1.8V) */
+ case 0x3: /* NAND Flash (3.0V) */
+ socfpga_per_reset(SOCFPGA_RESET(NAND), 0);
+ return BOOT_DEVICE_NAND;
+ case 0x4: /* SD/MMC External Transceiver (1.8V) */
+ case 0x5: /* SD/MMC Internal Transceiver (3.0V) */
+ socfpga_per_reset(SOCFPGA_RESET(SDMMC), 0);
+ socfpga_per_reset(SOCFPGA_RESET(DMA), 0);
+ return BOOT_DEVICE_MMC1;
+ case 0x6: /* QSPI Flash (1.8V) */
+ case 0x7: /* QSPI Flash (3.0V) */
+ socfpga_per_reset(SOCFPGA_RESET(QSPI), 0);
+ return BOOT_DEVICE_SPI;
+ default:
+ printf("Invalid boot device (bsel=%08x)!\n", bsel);
+ hang();
+ }
+}
+
+#ifdef CONFIG_SPL_MMC_SUPPORT
+u32 spl_boot_mode(const u32 boot_device)
+{
+#if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
+ return MMCSD_MODE_FS;
+#else
+ return MMCSD_MODE_RAW;
+#endif
+}
+#endif
+
+void spl_board_init(void)
+{
+ /* configuring the clock based on handoff */
+ cm_basic_init(gd->fdt_blob);
+ WATCHDOG_RESET();
+
+ config_dedicated_pins(gd->fdt_blob);
+ WATCHDOG_RESET();
+
+ /* Release UART from reset */
+ socfpga_reset_uart(0);
+
+ /* enable console uart printing */
+ preloader_console_init();
+}
+
+void board_init_f(ulong dummy)
+{
+ /*
+ * Configure Clock Manager to use intosc clock instead external osc to
+ * ensure success watchdog operation. We do it as early as possible.
+ */
+ cm_use_intosc();
+
+ socfpga_watchdog_disable();
+
+ arch_early_init_r();
+
+#ifdef CONFIG_HW_WATCHDOG
+ /* release osc1 watchdog timer 0 from reset */
+ socfpga_reset_deassert_osc1wd0();
+
+ /* reconfigure and enable the watchdog */
+ hw_watchdog_init();
+ WATCHDOG_RESET();
+#endif /* CONFIG_HW_WATCHDOG */
+}
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2012 Altera Corporation <www.altera.com>
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/pl310.h>
+#include <asm/u-boot.h>
+#include <asm/utils.h>
+#include <image.h>
+#include <asm/arch/reset_manager.h>
+#include <spl.h>
+#include <asm/arch/system_manager.h>
+#include <asm/arch/freeze_controller.h>
+#include <asm/arch/clock_manager.h>
+#include <asm/arch/misc.h>
+#include <asm/arch/scan_manager.h>
+#include <asm/arch/sdram.h>
+#include <asm/arch/scu.h>
+#include <asm/arch/nic301.h>
+#include <asm/sections.h>
+#include <fdtdec.h>
+#include <watchdog.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct pl310_regs *const pl310 =
+ (struct pl310_regs *)CONFIG_SYS_PL310_BASE;
+static struct scu_registers *scu_regs =
+ (struct scu_registers *)SOCFPGA_MPUSCU_ADDRESS;
+static struct nic301_registers *nic301_regs =
+ (struct nic301_registers *)SOCFPGA_L3REGS_ADDRESS;
+static const struct socfpga_system_manager *sysmgr_regs =
+ (struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
+
+u32 spl_boot_device(void)
+{
+ const u32 bsel = readl(&sysmgr_regs->bootinfo);
+
+ switch (SYSMGR_GET_BOOTINFO_BSEL(bsel)) {
+ case 0x1: /* FPGA (HPS2FPGA Bridge) */
+ return BOOT_DEVICE_RAM;
+ case 0x2: /* NAND Flash (1.8V) */
+ case 0x3: /* NAND Flash (3.0V) */
+ socfpga_per_reset(SOCFPGA_RESET(NAND), 0);
+ return BOOT_DEVICE_NAND;
+ case 0x4: /* SD/MMC External Transceiver (1.8V) */
+ case 0x5: /* SD/MMC Internal Transceiver (3.0V) */
+ socfpga_per_reset(SOCFPGA_RESET(SDMMC), 0);
+ socfpga_per_reset(SOCFPGA_RESET(DMA), 0);
+ return BOOT_DEVICE_MMC1;
+ case 0x6: /* QSPI Flash (1.8V) */
+ case 0x7: /* QSPI Flash (3.0V) */
+ socfpga_per_reset(SOCFPGA_RESET(QSPI), 0);
+ return BOOT_DEVICE_SPI;
+ default:
+ printf("Invalid boot device (bsel=%08x)!\n", bsel);
+ hang();
+ }
+}
+
+#ifdef CONFIG_SPL_MMC_SUPPORT
+u32 spl_boot_mode(const u32 boot_device)
+{
+#if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
+ return MMCSD_MODE_FS;
+#else
+ return MMCSD_MODE_RAW;
+#endif
+}
+#endif
+
+static void socfpga_nic301_slave_ns(void)
+{
+ writel(0x1, &nic301_regs->lwhps2fpgaregs);
+ writel(0x1, &nic301_regs->hps2fpgaregs);
+ writel(0x1, &nic301_regs->acp);
+ writel(0x1, &nic301_regs->rom);
+ writel(0x1, &nic301_regs->ocram);
+ writel(0x1, &nic301_regs->sdrdata);
+}
+
+void board_init_f(ulong dummy)
+{
+ const struct cm_config *cm_default_cfg = cm_get_default_config();
+ unsigned long sdram_size;
+ unsigned long reg;
+
+ /*
+ * First C code to run. Clear fake OCRAM ECC first as SBE
+ * and DBE might triggered during power on
+ */
+ reg = readl(&sysmgr_regs->eccgrp_ocram);
+ if (reg & SYSMGR_ECC_OCRAM_SERR)
+ writel(SYSMGR_ECC_OCRAM_SERR | SYSMGR_ECC_OCRAM_EN,
+ &sysmgr_regs->eccgrp_ocram);
+ if (reg & SYSMGR_ECC_OCRAM_DERR)
+ writel(SYSMGR_ECC_OCRAM_DERR | SYSMGR_ECC_OCRAM_EN,
+ &sysmgr_regs->eccgrp_ocram);
+
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ socfpga_nic301_slave_ns();
+
+ /* Configure ARM MPU SNSAC register. */
+ setbits_le32(&scu_regs->sacr, 0xfff);
+
+ /* Remap SDRAM to 0x0 */
+ writel(0x1, &nic301_regs->remap); /* remap.mpuzero */
+ writel(0x1, &pl310->pl310_addr_filter_start);
+
+ debug("Freezing all I/O banks\n");
+ /* freeze all IO banks */
+ sys_mgr_frzctrl_freeze_req();
+
+ /* Put everything into reset but L4WD0. */
+ socfpga_per_reset_all();
+ /* Put FPGA bridges into reset too. */
+ socfpga_bridges_reset(1);
+
+ socfpga_per_reset(SOCFPGA_RESET(SDR), 0);
+ socfpga_per_reset(SOCFPGA_RESET(UART0), 0);
+ socfpga_per_reset(SOCFPGA_RESET(OSC1TIMER0), 0);
+
+ timer_init();
+
+ debug("Reconfigure Clock Manager\n");
+ /* reconfigure the PLLs */
+ if (cm_basic_init(cm_default_cfg))
+ hang();
+
+ /* Enable bootrom to configure IOs. */
+ sysmgr_config_warmrstcfgio(1);
+
+ /* configure the IOCSR / IO buffer settings */
+ if (scan_mgr_configure_iocsr())
+ hang();
+
+ sysmgr_config_warmrstcfgio(0);
+
+ /* configure the pin muxing through system manager */
+ sysmgr_config_warmrstcfgio(1);
+ sysmgr_pinmux_init();
+ sysmgr_config_warmrstcfgio(0);
+
+ /* De-assert reset for peripherals and bridges based on handoff */
+ reset_deassert_peripherals_handoff();
+ socfpga_bridges_reset(0);
+
+ debug("Unfreezing/Thaw all I/O banks\n");
+ /* unfreeze / thaw all IO banks */
+ sys_mgr_frzctrl_thaw_req();
+
+ /* enable console uart printing */
+ preloader_console_init();
+
+ if (sdram_mmr_init_full(0xffffffff) != 0) {
+ puts("SDRAM init failed.\n");
+ hang();
+ }
+
+ debug("SDRAM: Calibrating PHY\n");
+ /* SDRAM calibration */
+ if (sdram_calibration_full() == 0) {
+ puts("SDRAM calibration failed.\n");
+ hang();
+ }
+
+ sdram_size = sdram_calculate_size();
+ debug("SDRAM: %ld MiB\n", sdram_size >> 20);
+
+ /* Sanity check ensure correct SDRAM size specified */
+ if (get_ram_size(0, sdram_size) != sdram_size) {
+ puts("SDRAM size check failed!\n");
+ hang();
+ }
+
+ socfpga_bridges_reset(1);
+
+ /* Configure simple malloc base pointer into RAM. */
+ gd->malloc_base = CONFIG_SYS_TEXT_BASE + (1024 * 1024);
+}
projects / oweals / u-boot.git / commitdiff