* LAW(Local Access Window) configuration:
*
* 0x0000_0000 0x7fff_ffff DDR 2G
+ * if PCI
* 0x8000_0000 0x9fff_ffff PCI1 MEM 512M
* 0xa000_0000 0xbfff_ffff PCI2 MEM 512M
- * 0xc000_0000 0xdfff_ffff RapidIO 512M
- * 0xe200_0000 0xe2ff_ffff PCI1 IO 16M
- * 0xe300_0000 0xe3ff_ffff PCI2 IO 16M
- * 0xf800_0000 0xf80f_ffff CCSRBAR 1M
- * 0xf810_0000 0xf81f_ffff PIXIS 1M
- * 0xfe00_0000 0xffff_ffff FLASH (boot bank) 32M
+ * else if RIO
+ * 0x8000_0000 0x9fff_ffff RapidIO 512M
+ * endif
+ * 0xffc0_0000 0xffc0_ffff PCI1 IO 64K
+ * 0xffc1_0000 0xffc1_ffff PCI2 IO 64K
+ * 0xffe0_0000 0xffef_ffff CCSRBAR 1M
+ * 0xffdf_0000 0xffe0_0000 PIXIS, CF 64K
+ * 0xef80_0000 0xefff_ffff FLASH (boot bank) 8M
*
* Notes:
- * CCSRBAR don't need a configured Local Access Window.
+ * CCSRBAR doesn't need a configured Local Access Window.
* If flash is 8M at default position (last 8M), no LAW needed.
*/
#ifdef CONFIG_PCI
SET_LAW(CONFIG_SYS_PCI1_MEM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_PCI_1),
SET_LAW(CONFIG_SYS_PCI2_MEM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_PCI_2),
- SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI_1),
- SET_LAW(CONFIG_SYS_PCI2_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI_2),
+ SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCI_1),
+ SET_LAW(CONFIG_SYS_PCI2_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCI_2),
#elif defined(CONFIG_RIO)
SET_LAW(CONFIG_SYS_RIO_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_RIO),
#endif
- SET_LAW(PIXIS_BASE, LAW_SIZE_2M, LAW_TRGT_IF_LBC),
+ SET_LAW(PIXIS_BASE, LAW_SIZE_64K, LAW_TRGT_IF_LBC),
SET_LAW(CONFIG_SYS_FLASH_BASE, LAW_SIZE_8M, LAW_TRGT_IF_LBC),
};
3. Flash U-Boot
---------------
-The flash range 0xFF800000 to 0xFFFFFFFF can be divided into 2 halves.
+The flash range 0xEF800000 to 0xEFFFFFFF can be divided into 2 halves.
It is possible to use either half to boot using u-boot. Switch 5 bit 2
is used for this purpose.
-0xFF800000 to 0xFFBFFFFF - 4MB
-0xFFC00000 to 0xFFFFFFFF - 4MB
-When this bit is 0, U-Boot is at 0xFFF00000.
-When this bit is 1, U-Boot is at 0xFFB00000.
+0xEF800000 to 0xEFBFFFFF - 4MB
+0xEFC00000 to 0xEFFFFFFF - 4MB
+When this bit is 0, U-Boot is at 0xEFF00000.
+When this bit is 1, U-Boot is at 0xEFB00000.
Use the above mentioned flash commands to program the other half, and
use switch 5, bit 2 to alternate between the halves. Note: The booting
-version of U-Boot will always be at 0xFFF00000.
+version of U-Boot will always be at 0xEFF00000.
-To Flash U-Boot into the booting bank (0xFFC00000 - 0xFFFFFFFF):
+To Flash U-Boot into the booting bank (0xEFC00000 - 0xEFFFFFFF):
tftp 1000000 u-boot.bin
protect off all
- erase fff00000 +$filesize
- cp.b 1000000 fff00000 $filesize
+ erase eff00000 +$filesize
+ cp.b 1000000 eff00000 $filesize
or use tftpflash command:
run tftpflash
-To Flash U-boot into the alternative bank (0xFF800000 - 0xFFBFFFFF):
+To Flash U-boot into the alternative bank (0xEF800000 - 0xEFBFFFFF):
tftp 1000000 u-boot.bin
- erase ffb00000 +$filesize
- cp.b 1000000 ffb00000 $filesize
+ erase efb00000 +$filesize
+ cp.b 1000000 efb00000 $filesize
4. Memory Map
-------------
+NOTE: RIO and PCI are mutually exclusive, so they share an address
Memory Range Device Size
------------ ------ ----
0x0000_0000 0x7fff_ffff DDR 2G
+ 0x8000_0000 0x9fff_ffff RIO MEM 512M
0x8000_0000 0x9fff_ffff PCI1/PEX1 MEM 512M
- 0xa000_0000 0xafff_ffff PCI2/PEX2 MEM 512M
- 0xf800_0000 0xf80f_ffff CCSR 1M
- 0xf810_0000 0xf81f_ffff PIXIS 1M
+ 0xa000_0000 0xbfff_ffff PCI2/PEX2 MEM 512M
+ 0xffe0_0000 0xffef_ffff CCSR 1M
+ 0xffdf_0000 0xffdf_7fff PIXIS 8K
+ 0xffdf_8000 0xffdf_ffff CF 8K
0xf840_0000 0xf840_3fff Stack space 32K
- 0xe200_0000 0xe2ff_ffff PCI1/PEX1 IO 16M
- 0xe300_0000 0xe3ff_ffff PCI2/PEX2 IO 16M
- 0xfe00_0000 0xfeff_ffff Flash(alternate)16M
- 0xff00_0000 0xffff_ffff Flash(boot bank)16M
+ 0xffc0_0000 0xffc0_ffff PCI1/PEX1 IO 64K
+ 0xffc1_0000 0xffc1_ffff PCI2/PEX2 IO 64K
+ 0xef80_0000 0xefff_ffff Flash 8M
5. pixis_reset command
--------------------
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000)
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */
+#define CONFIG_SYS_FLASH_BASE 0xef800000 /* start of FLASH 8M */
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CF_BASE) \
| 0x00001001) /* port size 16bit */
-#define CONFIG_SYS_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/
+#define CONFIG_SYS_OR2_PRELIM 0xffffeff7 /* 32k Compact Flash */
#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE) \
| 0x00000801) /* port size 8bit */
-#define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
+#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32k PIXIS area*/
+/*
+ * The LBC_BASE is the base of the region that contains the PIXIS and the CF.
+ * The PIXIS and CF by themselves aren't large enough to take up the 128k
+ * required for the smallest BAT mapping, so there's a 64k hole.
+ */
+#define CONFIG_SYS_LBC_BASE 0xffde0000
#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
-#define PIXIS_BASE (CONFIG_SYS_CCSRBAR + 0x00100000) /* PIXIS registers */
+#define PIXIS_BASE (CONFIG_SYS_LBC_BASE + 0x00010000)
+#define PIXIS_SIZE 0x00008000 /* 32k */
#define PIXIS_ID 0x0 /* Board ID at offset 0 */
#define PIXIS_VER 0x1 /* Board version at offset 1 */
#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
#define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/
/* Compact flash shares a BAT with PIXIS; make sure they're contiguous */
-#define CF_BASE (PIXIS_BASE + 0x00100000)
+#define CF_BASE (PIXIS_BASE + PIXIS_SIZE)
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
/*
* RapidIO MMU
*/
-#define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 /* base address */
+#define CONFIG_SYS_RIO_MEM_BASE 0x80000000 /* base address */
#define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE
#define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCI1_IO_PHYS 0xffc00000
+#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64K */
/* For RTL8139 */
#define KSEG1ADDR(x) ({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);})
#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
#define CONFIG_SYS_PCI2_IO_PHYS (CONFIG_SYS_PCI1_IO_PHYS \
+ CONFIG_SYS_PCI1_IO_SIZE)
-#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCI2_IO_SIZE CONFIG_SYS_PCI1_IO_SIZE
#if defined(CONFIG_PCI)
#endif /* CONFIG_TSEC_ENET */
/*
- * BAT0 2G Cacheable, non-guarded
- * 0x0000_0000 2G DDR
+ * BAT0 DDR
*/
#define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
#define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U
/*
- * BAT1 unused
+ * BAT1 LBC (PIXIS/CF)
*/
-#define CONFIG_SYS_DBAT1L 0
-#define CONFIG_SYS_DBAT1U 0
-#define CONFIG_SYS_IBAT1L 0
-#define CONFIG_SYS_IBAT1U 0
+#define CONFIG_SYS_DBAT1L (CONFIG_SYS_LBC_BASE | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT1U (CONFIG_SYS_LBC_BASE | BATU_BL_128K \
+ | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_LBC_BASE | BATL_PP_RW \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U
/* if CONFIG_PCI:
- * BAT2 1G Cache-inhibited, guarded
- * 0x8000_0000 512M PCI-Express 1 Memory
- * 0xa000_0000 512M PCI-Express 2 Memory
- * Changed it for operating from 0xd0000000
- *
+ * BAT2 PCI1 and PCI1 MEM
* if CONFIG_RIO
- * BAT2 512M Cache-inhibited, guarded
- * 0xc000_0000 512M RapidIO Memory
+ * BAT2 Rapidio Memory
*/
#ifdef CONFIG_PCI
#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW \
#endif
/*
- * BAT3 4M Cache-inhibited, guarded
- * 0xf800_0000 4M CCSR
+ * BAT3 CCSR Space
*/
#define CONFIG_SYS_DBAT3L ( CONFIG_SYS_CCSRBAR | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \
+ | BATU_VP)
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U
/*
- * BAT4 32M Cache-inhibited, guarded
- * 0xe200_0000 16M PCI-Express 1 I/O
- * 0xe300_0000 16M PCI-Express 2 I/0
- * Note that this is at 0xe0000000
+ * BAT4 PCI1_IO and PCI2_IO
*/
#define CONFIG_SYS_DBAT4L ( CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCI1_IO_PHYS | BATU_BL_128K \
+ | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U
/*
- * BAT5 128K Cacheable, non-guarded
- * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
+ * BAT5 Init RAM for stack in the CPU DCache (no backing memory)
*/
#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U
/*
- * BAT6 8M Cache-inhibited, guarded
- * 0xff80_0000 8M FLASH
+ * BAT6 FLASH
*/
#define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
-/* Leave BAT7 free here - it is used for various things later */
+/*
+ * BAT7 FREE - used later for tmp mappings
+ */
#define CONFIG_SYS_DBAT7L 0x00000000
#define CONFIG_SYS_DBAT7U 0x00000000
#define CONFIG_SYS_IBAT7L 0x00000000
projects / oweals / u-boot.git / commitdiff