avr32: delete non generic board mimc200
authorAndreas Bießmann <andreas.devel@googlemail.com>
Mon, 11 May 2015 11:07:26 +0000 (13:07 +0200)
committerAndreas Bießmann <andreas.devel@googlemail.com>
Wed, 10 Jun 2015 12:03:22 +0000 (14:03 +0200)
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
arch/avr32/Kconfig
board/mimc/mimc200/Kconfig [deleted file]
board/mimc/mimc200/MAINTAINERS [deleted file]
board/mimc/mimc200/Makefile [deleted file]
board/mimc/mimc200/mimc200.c [deleted file]
configs/mimc200_defconfig [deleted file]
include/configs/mimc200.h [deleted file]

index cfcdbe7565d7a470da521784891e2401eb615ecc..0c7b1ba11af48dc100a0b17f594cf8dbbd8c2a3b 100644 (file)
@@ -29,15 +29,11 @@ config TARGET_ATSTK1006
 config TARGET_GRASSHOPPER
        bool "Support grasshopper"
 
-config TARGET_MIMC200
-       bool "Support mimc200"
-
 endchoice
 
 source "board/atmel/atngw100/Kconfig"
 source "board/atmel/atngw100mkii/Kconfig"
 source "board/atmel/atstk1000/Kconfig"
 source "board/in-circuit/grasshopper/Kconfig"
-source "board/mimc/mimc200/Kconfig"
 
 endmenu
diff --git a/board/mimc/mimc200/Kconfig b/board/mimc/mimc200/Kconfig
deleted file mode 100644 (file)
index 18736d7..0000000
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_MIMC200
-
-config SYS_BOARD
-       default "mimc200"
-
-config SYS_VENDOR
-       default "mimc"
-
-config SYS_SOC
-       default "at32ap700x"
-
-config SYS_CONFIG_NAME
-       default "mimc200"
-
-endif
diff --git a/board/mimc/mimc200/MAINTAINERS b/board/mimc/mimc200/MAINTAINERS
deleted file mode 100644 (file)
index 6cb51dd..0000000
+++ /dev/null
@@ -1,6 +0,0 @@
-MIMC200 BOARD
-M:     Mark Jackson <mpfj@mimc.co.uk>
-S:     Maintained
-F:     board/mimc/mimc200/
-F:     include/configs/mimc200.h
-F:     configs/mimc200_defconfig
diff --git a/board/mimc/mimc200/Makefile b/board/mimc/mimc200/Makefile
deleted file mode 100644 (file)
index 5c30c0d..0000000
+++ /dev/null
@@ -1,6 +0,0 @@
-#
-# Copyright (C) 2005-2006 Atmel Corporation
-#
-# SPDX-License-Identifier:     GPL-2.0+
-
-obj-y  := mimc200.o
diff --git a/board/mimc/mimc200/mimc200.c b/board/mimc/mimc200/mimc200.c
deleted file mode 100644 (file)
index f078295..0000000
+++ /dev/null
@@ -1,197 +0,0 @@
-/*
- * Copyright (C) 2006 Atmel Corporation
- *
- * SPDX-License-Identifier:    GPL-2.0+
- */
-#include <common.h>
-#include <netdev.h>
-
-#include <asm/io.h>
-#include <asm/sdram.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/hmatrix.h>
-#include <asm/arch/mmu.h>
-#include <asm/arch/portmux.h>
-#include <atmel_lcdc.h>
-#include <lcd.h>
-
-#include "../../../arch/avr32/cpu/hsmc3.h"
-
-struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = {
-       {
-               .virt_pgno      = CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT,
-               .nr_pages       = CONFIG_SYS_FLASH_SIZE >> MMU_PAGE_SHIFT,
-               .phys           = (CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT)
-                                       | MMU_VMR_CACHE_NONE,
-       }, {
-               .virt_pgno      = EBI_SRAM_CS2_BASE >> MMU_PAGE_SHIFT,
-               .nr_pages       = EBI_SRAM_CS2_SIZE >> MMU_PAGE_SHIFT,
-               .phys           = (EBI_SRAM_CS2_BASE >> MMU_PAGE_SHIFT)
-                                       | MMU_VMR_CACHE_NONE,
-       }, {
-               .virt_pgno      = CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT,
-               .nr_pages       = EBI_SDRAM_SIZE >> MMU_PAGE_SHIFT,
-               .phys           = (CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT)
-                                       | MMU_VMR_CACHE_WRBACK,
-       },
-};
-
-#if defined(CONFIG_LCD)
-/* 480x272x16 @ 72 Hz */
-vidinfo_t panel_info = {
-       .vl_col                 = 480,          /* Number of columns */
-       .vl_row                 = 272,          /* Number of rows */
-       .vl_clk                 = 5000000,      /* pixel clock in ps */
-       .vl_sync                = ATMEL_LCDC_INVCLK_INVERTED |
-                                 ATMEL_LCDC_INVLINE_INVERTED |
-                                 ATMEL_LCDC_INVFRAME_INVERTED,
-       .vl_bpix                = LCD_COLOR16,  /* Bits per pixel, BPP = 2^n */
-       .vl_tft                 = 1,            /* 0 = passive, 1 = TFT */
-       .vl_hsync_len           = 42,           /* Length of horizontal sync */
-       .vl_left_margin         = 1,            /* Time from sync to picture */
-       .vl_right_margin        = 1,            /* Time from picture to sync */
-       .vl_vsync_len           = 1,            /* Length of vertical sync */
-       .vl_upper_margin        = 12,           /* Time from sync to picture */
-       .vl_lower_margin        = 1,            /* Time from picture to sync */
-       .mmio                   = LCDC_BASE,    /* Memory mapped registers */
-};
-
-void lcd_enable(void)
-{
-}
-
-void lcd_disable(void)
-{
-}
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static const struct sdram_config sdram_config = {
-       .data_bits      = SDRAM_DATA_16BIT,
-       .row_bits       = 13,
-       .col_bits       = 9,
-       .bank_bits      = 2,
-       .cas            = 3,
-       .twr            = 2,
-       .trc            = 6,
-       .trp            = 2,
-       .trcd           = 2,
-       .tras           = 6,
-       .txsr           = 6,
-       /* 15.6 us */
-       .refresh_period = (156 * (SDRAMC_BUS_HZ / 1000)) / 10000,
-};
-
-int board_early_init_f(void)
-{
-       /* Enable SDRAM in the EBI mux */
-       hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE));
-
-       /* Enable 26 address bits and NCS2 */
-       portmux_enable_ebi(16, 26, PORTMUX_EBI_CS(2), PORTMUX_DRIVE_HIGH);
-       sdram_init(uncached(EBI_SDRAM_BASE), &sdram_config);
-
-       portmux_enable_usart1(PORTMUX_DRIVE_MIN);
-
-       /* de-assert "force sys reset" pin */
-       portmux_select_gpio(PORTMUX_PORT_D, 1 << 15,
-                       PORTMUX_DIR_OUTPUT | PORTMUX_INIT_HIGH);
-
-       /* init custom i/o */
-       /* cpu type inputs */
-       portmux_select_gpio(PORTMUX_PORT_E, (1 << 19) | (1 << 20) | (1 << 23),
-                       PORTMUX_DIR_INPUT);
-       /* main board type inputs */
-       portmux_select_gpio(PORTMUX_PORT_B, (1 << 19) | (1 << 29),
-                       PORTMUX_DIR_INPUT);
-       /* DEBUG input (use weak pullup) */
-       portmux_select_gpio(PORTMUX_PORT_E, 1 << 21,
-                       PORTMUX_DIR_INPUT | PORTMUX_PULL_UP);
-
-       /* are we suppressing the console ? */
-       if (gpio_get_value(GPIO_PIN_PE(21)) == 1)
-               gd->flags |= (GD_FLG_SILENT | GD_FLG_DISABLE_CONSOLE);
-
-       /* reset phys */
-       portmux_select_gpio(PORTMUX_PORT_E, 1 << 24, PORTMUX_DIR_INPUT);
-       portmux_select_gpio(PORTMUX_PORT_C, 1 << 18,
-                       PORTMUX_DIR_OUTPUT | PORTMUX_INIT_HIGH);
-
-       udelay(5000);
-
-       /* release phys reset */
-       gpio_set_value(GPIO_PIN_PC(18), 0);     /* PHY RESET (Release)  */
-
-       /* setup Data Flash chip select (NCS2) */
-       hsmc3_writel(MODE2, 0x20121003);
-       hsmc3_writel(CYCLE2, 0x000a0009);
-       hsmc3_writel(PULSE2, 0x0a060806);
-       hsmc3_writel(SETUP2, 0x00030102);
-
-       /* setup FRAM chip select (NCS3) */
-       hsmc3_writel(MODE3, 0x10120001);
-       hsmc3_writel(CYCLE3, 0x001e001d);
-       hsmc3_writel(PULSE3, 0x08040704);
-       hsmc3_writel(SETUP3, 0x02050204);
-
-#if defined(CONFIG_MACB)
-       /* init macb0 pins */
-       portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
-       portmux_enable_macb1(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
-#endif
-
-#if defined(CONFIG_MMC)
-       portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW);
-#endif
-
-#if defined(CONFIG_LCD)
-       portmux_enable_lcdc(1);
-#endif
-
-       return 0;
-}
-
-int board_early_init_r(void)
-{
-       gd->bd->bi_phy_id[0] = 0x01;
-       gd->bd->bi_phy_id[1] = 0x03;
-       return 0;
-}
-
-int board_postclk_init(void)
-{
-       /* Use GCLK0 as 10MHz output */
-       gclk_enable_output(0, PORTMUX_DRIVE_LOW);
-       gclk_set_rate(0, GCLK_PARENT_OSC0, 10000000);
-       return 0;
-}
-
-/* SPI chip select control */
-#ifdef CONFIG_ATMEL_SPI
-#include <spi.h>
-
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
-       return (bus == 0) && (cs == 0);
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
-}
-#endif /* CONFIG_ATMEL_SPI */
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bi)
-{
-       macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0, bi->bi_phy_id[0]);
-       macb_eth_initialize(1, (void *)ATMEL_BASE_MACB1, bi->bi_phy_id[1]);
-
-       return 0;
-}
-#endif
diff --git a/configs/mimc200_defconfig b/configs/mimc200_defconfig
deleted file mode 100644 (file)
index 85c646e..0000000
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_AVR32=y
-CONFIG_TARGET_MIMC200=y
-CONFIG_CMD_NET=y
diff --git a/include/configs/mimc200.h b/include/configs/mimc200.h
deleted file mode 100644 (file)
index e8e5ae7..0000000
+++ /dev/null
@@ -1,176 +0,0 @@
-/*
- * Copyright (C) 2006 Atmel Corporation
- *
- * Configuration settings for the AVR32 Network Gateway
- *
- * SPDX-License-Identifier:    GPL-2.0+
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/hardware.h>
-
-#define CONFIG_AT32AP
-#define CONFIG_AT32AP7000
-#define CONFIG_MIMC200
-
-#define CONFIG_MIMC200_EXT_FLASH
-
-/*
- * Set up the PLL to run at 140 MHz, the CPU to run at the PLL
- * frequency, the HSB and PBB busses to run at 1/2 the PLL frequency
- * and the PBA bus to run at 1/4 the PLL frequency.
- */
-#define CONFIG_PLL
-#define CONFIG_SYS_POWER_MANAGER
-#define CONFIG_SYS_OSC0_HZ                     10000000
-#define CONFIG_SYS_PLL0_DIV                    1
-#define CONFIG_SYS_PLL0_MUL                    15
-#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES        16
-#define CONFIG_SYS_CLKDIV_CPU                  0
-#define CONFIG_SYS_CLKDIV_HSB                  1
-#define CONFIG_SYS_CLKDIV_PBA                  2
-#define CONFIG_SYS_CLKDIV_PBB                  1
-
-/* Reserve VM regions for SDRAM, NOR flash and FRAM */
-#define CONFIG_SYS_NR_VM_REGIONS               3
-
-/*
- * The PLLOPT register controls the PLL like this:
- *   icp = PLLOPT<2>
- *   ivco = PLLOPT<1:0>
- *
- * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
- */
-#define CONFIG_SYS_PLL0_OPT                    0x04
-
-#define CONFIG_USART_BASE                      ATMEL_BASE_USART1
-#define CONFIG_USART_ID                                1
-
-#define CONFIG_MIMC200_DBGLINK         1
-
-/* User serviceable stuff */
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_STACKSIZE               (2048)
-
-#define CONFIG_BAUDRATE                        115200
-#define CONFIG_BOOTARGS                                                        \
-       "root=/dev/mtdblock1 rootfstype=jffs2 fbmem=512k console=ttyS1"
-#define CONFIG_BOOTCOMMAND                                             \
-       "fsload boot/uImage; bootm"
-
-#define CONFIG_SILENT_CONSOLE       /* enable silent startup */
-#define CONFIG_DISABLE_CONSOLE      /* disable console */
-#define CONFIG_SYS_DEVICE_NULLDEV   /* include nulldev device */
-
-#define CONFIG_LCD                     1
-
-/*
- * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
- * data on the serial line may interrupt the boot sequence.
- */
-#define CONFIG_BOOTDELAY               0
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_AUTOBOOT
-
-/*
- * After booting the board for the first time, new ethernet addresses
- * should be generated and assigned to the environment variables
- * "ethaddr" and "eth1addr". This is normally done during production.
- */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-
-/*
- * BOOTP/DHCP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MMC
-
-#define CONFIG_ATMEL_USART
-#define CONFIG_MACB
-#define CONFIG_PORTMUX_PIO
-#define CONFIG_SYS_NR_PIOS                     5
-#define CONFIG_SYS_HSDRAMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#define CONFIG_GENERIC_MMC
-
-#if defined(CONFIG_LCD)
-#define CONFIG_CMD_BMP
-#define CONFIG_ATMEL_LCD               1
-#define LCD_BPP                                LCD_COLOR16
-#define CONFIG_BMP_16BPP               1
-#define CONFIG_FB_ADDR                 0x10600000
-#define CONFIG_WHITE_ON_BLACK          1
-#define CONFIG_VIDEO_BMP_GZIP          1
-#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE         262144
-#define CONFIG_ATMEL_LCD_BGR555                1
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV   1
-#define CONFIG_SPLASH_SCREEN           1
-#endif
-
-#define CONFIG_SYS_DCACHE_LINESZ               32
-#define CONFIG_SYS_ICACHE_LINESZ               32
-
-#define CONFIG_NR_DRAM_BANKS           1
-
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-
-#define CONFIG_SYS_FLASH_BASE                  0x00000000
-#define CONFIG_SYS_FLASH_SIZE                  0x800000
-#define CONFIG_SYS_MAX_FLASH_BANKS             1
-#define CONFIG_SYS_MAX_FLASH_SECT              135
-
-#define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_TEXT_BASE           0x00000000
-
-#define CONFIG_SYS_INTRAM_BASE                 INTERNAL_SRAM_BASE
-#define CONFIG_SYS_INTRAM_SIZE                 INTERNAL_SRAM_SIZE
-#define CONFIG_SYS_SDRAM_BASE                  EBI_SDRAM_BASE
-
-#define CONFIG_SYS_FRAM_BASE                   0x08000000
-#define CONFIG_SYS_FRAM_SIZE                   0x20000
-
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SIZE                        65536
-#define CONFIG_ENV_ADDR                        (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_INIT_SP_ADDR                (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
-
-#define CONFIG_SYS_MALLOC_LEN                  (1024*1024)
-
-/* Allow 4MB for the kernel run-time image */
-#define CONFIG_SYS_LOAD_ADDR                   (EBI_SDRAM_BASE + 0x00400000)
-#define CONFIG_SYS_BOOTPARAMS_LEN              (16 * 1024)
-
-/* Other configuration settings that shouldn't have to change all that often */
-#define CONFIG_SYS_PROMPT                      "U-Boot> "
-#define CONFIG_SYS_CBSIZE                      256
-#define CONFIG_SYS_MAXARGS                     16
-#define CONFIG_SYS_PBSIZE                      (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-
-#define CONFIG_SYS_MEMTEST_START               EBI_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END                 (CONFIG_SYS_MEMTEST_START + 0x1f00000)
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
-
-#endif /* __CONFIG_H */