exynos: Enable the LCD backlight for snow
authorSimon Glass <sjg@chromium.org>
Tue, 20 May 2014 12:01:42 +0000 (06:01 -0600)
committerMinkyu Kang <mk7.kang@samsung.com>
Wed, 28 May 2014 01:58:19 +0000 (10:58 +0900)
The backlight uses FETs on the TPS65090. Enable this so that the display
is visible.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
board/samsung/smdk5250/exynos5-dt.c
include/fdtdec.h
lib/fdtdec.c

index bce7583fd0241d9e4b5c4265814cbcc9531f2e87..d6ce1337b94ba6f06172ea6459c7162396dbc5ea 100644 (file)
@@ -11,9 +11,9 @@
 #include <i2c.h>
 #include <netdev.h>
 #include <spi.h>
+#include <asm/gpio.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/dwmmc.h>
-#include <asm/arch/gpio.h>
 #include <asm/arch/mmc.h>
 #include <asm/arch/pinmux.h>
 #include <asm/arch/power.h>
@@ -180,6 +180,59 @@ int exynos_power_init(void)
 #endif /* CONFIG_POWER */
 
 #ifdef CONFIG_LCD
+static int board_dp_bridge_setup(void)
+{
+       const int max_tries = 10;
+       int num_tries, node;
+
+       /*
+        * TODO(sjg): Use device tree for GPIOs when exynos GPIO
+        * numbering patch is in mainline.
+        */
+       debug("%s\n", __func__);
+       node = fdtdec_next_compatible(gd->fdt_blob, 0, COMPAT_NXP_PTN3460);
+       if (node < 0) {
+               debug("%s: No node for DP bridge in device tree\n", __func__);
+               return -ENODEV;
+       }
+
+       /* Setup the GPIOs */
+
+       /* PD is ACTIVE_LOW, and initially de-asserted */
+       gpio_set_pull(EXYNOS5_GPIO_Y25, S5P_GPIO_PULL_NONE);
+       gpio_direction_output(EXYNOS5_GPIO_Y25, 1);
+
+       /* Reset is ACTIVE_LOW */
+       gpio_set_pull(EXYNOS5_GPIO_X15, S5P_GPIO_PULL_NONE);
+       gpio_direction_output(EXYNOS5_GPIO_X15, 0);
+
+       udelay(10);
+       gpio_set_value(EXYNOS5_GPIO_X15, 1);
+
+       gpio_direction_input(EXYNOS5_GPIO_X07);
+
+       /*
+        * We need to wait for 90ms after bringing up the bridge since there
+        * is a phantom "high" on the HPD chip during its bootup.  The phantom
+        * high comes within 7ms of de-asserting PD and persists for at least
+        * 15ms.  The real high comes roughly 50ms after PD is de-asserted. The
+        * phantom high makes it hard for us to know when the NXP chip is up.
+        */
+       mdelay(90);
+
+       for (num_tries = 0; num_tries < max_tries; num_tries++) {
+               /* Check HPD.  If it's high, we're all good. */
+               if (gpio_get_value(EXYNOS5_GPIO_X07))
+                               return 0;
+
+               debug("%s: eDP bridge failed to come up; try %d of %d\n",
+                     __func__, num_tries, max_tries);
+       }
+
+       /* Immediately go into bridge reset if the hp line is not high */
+       return -ENODEV;
+}
+
 void exynos_cfg_lcd_gpio(void)
 {
        /* For Backlight */
@@ -198,4 +251,49 @@ void exynos_set_dp_phy(unsigned int onoff)
 {
        set_dp_phy_ctrl(onoff);
 }
+
+void exynos_backlight_on(unsigned int on)
+{
+       debug("%s(%u)\n", __func__, on);
+
+       if (!on)
+               return;
+
+#ifdef CONFIG_POWER_TPS65090
+       int ret;
+
+       ret = tps65090_fet_enable(1); /* Enable FET1, backlight */
+       if (ret)
+               return;
+
+       /* T5 in the LCD timing spec (defined as > 10ms) */
+       mdelay(10);
+
+       /* board_dp_backlight_pwm */
+       gpio_direction_output(EXYNOS5_GPIO_B20, 1);
+
+       /* T6 in the LCD timing spec (defined as > 10ms) */
+       mdelay(10);
+
+       /* board_dp_backlight_en */
+       gpio_direction_output(EXYNOS5_GPIO_X30, 1);
+#endif
+}
+
+void exynos_lcd_power_on(void)
+{
+       int ret;
+
+       debug("%s\n", __func__);
+
+#ifdef CONFIG_POWER_TPS65090
+       /* board_dp_lcd_vdd */
+       tps65090_fet_enable(6); /* Enable FET6, lcd panel */
+#endif
+
+       ret = board_dp_bridge_setup();
+       if (ret && ret != -ENODEV)
+               printf("LCD bridge failed to enable: %d\n", ret);
+}
+
 #endif
index 4b029d725887c8cd1231c9e2b8daad30f3ea709d..a7e6ee7fdfd9afc2284e71cbdc8ee423aa695bcc 100644 (file)
@@ -93,6 +93,7 @@ enum fdt_compat_id {
        COMPAT_SANDBOX_HOST_EMULATION,  /* Sandbox emulation of a function */
        COMPAT_SANDBOX_LCD_SDL,         /* Sandbox LCD emulation with SDL */
        COMPAT_TI_TPS65090,             /* Texas Instrument TPS65090 */
+       COMPAT_NXP_PTN3460,             /* NXP PTN3460 DP/LVDS bridge */
 
        COMPAT_COUNT,
 };
index 6cccfe57cd8d84339f4e4faa41a359b4811f556f..13d3d2f522f177fc994e7be91d859858d32e3d9c 100644 (file)
@@ -67,6 +67,7 @@ static const char * const compat_names[COMPAT_COUNT] = {
        COMPAT(SANDBOX_HOST_EMULATION, "sandbox,host-emulation"),
        COMPAT(SANDBOX_LCD_SDL, "sandbox,lcd-sdl"),
        COMPAT(TI_TPS65090, "ti,tps65090"),
+       COMPAT(COMPAT_NXP_PTN3460, "nxp,ptn3460"),
 };
 
 const char *fdtdec_get_compatible(enum fdt_compat_id id)