+++ /dev/null
-FU540-C000 RISC-V SoC
-=====================
-The FU540-C000 is the world’s first 4+1 64-bit RISC‑V SoC from SiFive.
-
-The HiFive Unleashed development platform is based on FU540-C000 and capable
-of running Linux.
-
-Mainline support
-================
-The support for following drivers are already enabled:
-1. SiFive UART Driver.
-2. SiFive PRCI Driver for clock.
-3. Cadence MACB ethernet driver for networking support.
-
-TODO:
-1. U-Boot expects the serial console device entry to be present under /chosen
- DT node. Example:
- chosen {
- stdout-path = "/soc/serial@10010000:115200";
- };
-
- Without a serial console U-Boot will panic.
-
-Building
-========
-1. Add the RISC-V toolchain to your PATH.
-2. Setup ARCH & cross compilation enviornment variable.
- a. export ARCH=riscv
- b. export CROSS_COMPILE=<riscv64 toolchain prefix>
-3. make sifive_fu540_defconfig
-4. make
-
-Flashing
-========
-The current U-Boot port is supported in S-mode only and loaded directly
-into DRAM.
-
-A prior stage (M-mode) firmware/bootloader (e.g OpenSBI) is required to
-boot the u-boot.bin in S-mode and provide M-mode runtime services.
-
-Currently, the u-boot.bin is used as a payload of the OpenSBI FW_PAYLOAD
-firmware. We need to compile OpenSBI with below command:
-make PLATFORM=sifive/fu540 FW_PAYLOAD_PATH=<path to u-boot.bin> FW_PAYLOAD_FDT_PATH=<path to hifive-unleashed-a00.dtb from Linux>
-(Note: Prefer hifive-unleashed-a00.dtb from Linux-5.3 or higher)
-(Note: Linux-5.2 is also fine but it does not have ethernet DT node)
-
-More detailed description of steps required to build FW_PAYLOAD firmware
-is beyond the scope of this document. Please refer OpenSBI documenation.
-(Note: OpenSBI git repo is at https://github.com/riscv/opensbi.git)
-
-Once the prior stage firmware/bootloader binary is generated, it should be
-copied to the first partition of the sdcard.
-
-sudo dd if=<prior_stage_firmware_binary> of=/dev/disk2s1 bs=1024
-
-Booting
-=======
-Once you plugin the sdcard and power up, you should see the U-Boot prompt.
-
-Sample boot log from HiFive Unleashed board
-===========================================
-U-Boot 2019.07-rc4-00013-g1837f893b0 (Jun 20 2019 - 11:08:48 +0530)
-
-CPU: rv64imafdc
-Model: SiFive HiFive Unleashed A00
-DRAM: 8 GiB
-In: serial@10010000
-Out: serial@10010000
-Err: serial@10010000
-Net: eth0: ethernet@10090000
-Hit any key to stop autoboot: 0
-=> version
-U-Boot 2019.07-rc4-00013-g1837f893b0 (Jun 20 2019 - 11:08:48 +0530)
-
-riscv64-linux-gcc.br_real (Buildroot 2018.11-rc2-00003-ga0787e9) 8.2.0
-GNU ld (GNU Binutils) 2.31.1
-=>
-===============================================================================
-
-Now you can configure your networking, tftp server and use tftp boot method to
-load uImage.
-
-==========================================================================
-=> setenv ipaddr 10.206.5.241
-=> setenv netmask 255.255.252.0
-=> setenv serverip 10.206.4.143
-=> setenv gateway 10.206.4.1
-=> tftpboot ${kernel_addr_r} /sifive/fu540/uImage
-ethernet@10090000: PHY present at 0
-ethernet@10090000: Starting autonegotiation...
-ethernet@10090000: Autonegotiation complete
-ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x7c00)
-Using ethernet@10090000 device
-TFTP from server 10.206.4.143; our IP address is 10.206.5.241
-Filename '/sifive/fu540/uImage'.
-Load address: 0x80600000
-Loading: #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- ########################################
- 1.5 MiB/s
-done
-Bytes transferred = 9162364 (8bce7c hex)
-=> tftpboot ${ramdisk_addr_r} /sifive/fu540/uRamdisk
-ethernet@10090000: PHY present at 0
-ethernet@10090000: Starting autonegotiation...
-ethernet@10090000: Autonegotiation complete
-ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x7c00)
-Using ethernet@10090000 device
-TFTP from server 10.206.4.143; our IP address is 10.206.5.241
-Filename '/sifive/fu540/uRamdisk'.
-Load address: 0x82500000
-Loading: #################################################################
- #################################################################
- ##################################
- 448.2 KiB/s
-done
-Bytes transferred = 2398272 (249840 hex)
-=> setenv bootargs "root=/dev/ram rw console=ttySIF0 earlycon=sbi"
-=> bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdtcontroladdr}
-## Booting kernel from Legacy Image at 80600000 ...
- Image Name: Linux
- Image Type: RISC-V Linux Kernel Image (uncompressed)
- Data Size: 9162300 Bytes = 8.7 MiB
- Load Address: 80200000
- Entry Point: 80200000
- Verifying Checksum ... OK
-## Loading init Ramdisk from Legacy Image at 82500000 ...
- Image Name: Linux RootFS
- Image Type: RISC-V Linux RAMDisk Image (uncompressed)
- Data Size: 2398208 Bytes = 2.3 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
-## Flattened Device Tree blob at ff795730
- Booting using the fdt blob at 0xff795730
- Loading Kernel Image ... OK
- Using Device Tree in place at 00000000ff795730, end 00000000ff799dac
-
-Starting kernel ...
-
-[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
-[ 0.000000] Linux version 5.2.0-rc1-00003-gb9543e66e700 (anup@anup-lab-machine) (gcc version 8.2.0 (Buildroot 2018.11-rc2-00003-ga0787e9)) #1 SMP Thu Jun 20 11:41:26 IST 2019
-[ 0.000000] earlycon: sbi0 at I/O port 0x0 (options '')
-[ 0.000000] printk: bootconsole [sbi0] enabled
-[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (2398208 bytes)
-[ 0.000000] Zone ranges:
-[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000ffffffff]
-[ 0.000000] Normal [mem 0x0000000100000000-0x000000027fffffff]
-[ 0.000000] Movable zone start for each node
-[ 0.000000] Early memory node ranges
-[ 0.000000] node 0: [mem 0x0000000080200000-0x000000027fffffff]
-[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000027fffffff]
-[ 0.000000] software IO TLB: mapped [mem 0xfb795000-0xff795000] (64MB)
-[ 0.000000] CPU with hartid=0 is not available
-[ 0.000000] CPU with hartid=0 is not available
-[ 0.000000] elf_hwcap is 0x112d
-[ 0.000000] percpu: Embedded 17 pages/cpu s29592 r8192 d31848 u69632
-[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975
-[ 0.000000] Kernel command line: root=/dev/ram rw console=ttySIF0 earlycon=sbi
-[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
-[ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
-[ 0.000000] Sorting __ex_table...
-[ 0.000000] Memory: 8182056K/8386560K available (5753K kernel code, 357K rwdata, 1804K rodata, 204K init, 808K bss, 204504K reserved, 0K cma-reserved)
-[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
-[ 0.000000] rcu: Hierarchical RCU implementation.
-[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
-[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
-[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
-[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
-[ 0.000000] plic: mapped 53 interrupts with 4 handlers for 9 contexts.
-[ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [2]
-[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
-[ 0.000007] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns
-[ 0.008553] Console: colour dummy device 80x25
-[ 0.012990] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=4000)
-[ 0.023103] pid_max: default: 32768 minimum: 301
-[ 0.028269] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
-[ 0.035068] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
-[ 0.042770] *** VALIDATE proc ***
-[ 0.045610] *** VALIDATE cgroup1 ***
-[ 0.049157] *** VALIDATE cgroup2 ***
-[ 0.053743] rcu: Hierarchical SRCU implementation.
-[ 0.058297] smp: Bringing up secondary CPUs ...
-[ 0.064134] smp: Brought up 1 node, 4 CPUs
-[ 0.069114] devtmpfs: initialized
-[ 0.073281] random: get_random_u32 called from bucket_table_alloc.isra.10+0x4e/0x160 with crng_init=0
-[ 0.082157] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
-[ 0.091634] futex hash table entries: 1024 (order: 4, 65536 bytes)
-[ 0.098480] NET: Registered protocol family 16
-[ 0.114101] vgaarb: loaded
-[ 0.116397] SCSI subsystem initialized
-[ 0.120358] usbcore: registered new interface driver usbfs
-[ 0.125541] usbcore: registered new interface driver hub
-[ 0.130936] usbcore: registered new device driver usb
-[ 0.136618] clocksource: Switched to clocksource riscv_clocksource
-[ 0.148108] NET: Registered protocol family 2
-[ 0.152358] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes)
-[ 0.159928] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
-[ 0.169027] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
-[ 0.178360] TCP: Hash tables configured (established 65536 bind 65536)
-[ 0.184653] UDP hash table entries: 4096 (order: 5, 131072 bytes)
-[ 0.190819] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
-[ 0.197618] NET: Registered protocol family 1
-[ 0.201892] RPC: Registered named UNIX socket transport module.
-[ 0.207395] RPC: Registered udp transport module.
-[ 0.212159] RPC: Registered tcp transport module.
-[ 0.216940] RPC: Registered tcp NFSv4.1 backchannel transport module.
-[ 0.223445] PCI: CLS 0 bytes, default 64
-[ 0.227726] Unpacking initramfs...
-[ 0.260556] Freeing initrd memory: 2336K
-[ 0.264652] workingset: timestamp_bits=62 max_order=21 bucket_order=0
-[ 0.278452] NFS: Registering the id_resolver key type
-[ 0.282841] Key type id_resolver registered
-[ 0.287067] Key type id_legacy registered
-[ 0.291155] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
-[ 0.298299] NET: Registered protocol family 38
-[ 0.302470] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
-[ 0.309906] io scheduler mq-deadline registered
-[ 0.314501] io scheduler kyber registered
-[ 0.354134] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
-[ 0.360725] 10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 4, base_baud = 0) is a SiFive UART v0
-[ 0.369191] printk: console [ttySIF0] enabled
-[ 0.369191] printk: console [ttySIF0] enabled
-[ 0.377938] printk: bootconsole [sbi0] disabled
-[ 0.377938] printk: bootconsole [sbi0] disabled
-[ 0.387298] 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 1, base_baud = 0) is a SiFive UART v0
-[ 0.396411] [drm] radeon kernel modesetting enabled.
-[ 0.409818] loop: module loaded
-[ 0.412606] libphy: Fixed MDIO Bus: probed
-[ 0.416870] macb 10090000.ethernet: Registered clk switch 'sifive-gemgxl-mgmt'
-[ 0.423570] macb: GEM doesn't support hardware ptp.
-[ 0.428469] libphy: MACB_mii_bus: probed
-[ 1.053009] Microsemi VSC8541 SyncE 10090000.ethernet-ffffffff:00: attached PHY driver [Microsemi VSC8541 SyncE] (mii_bus:phy_addr=10090000.ethernet-ffffffff:00, irq=POLL)
-[ 1.067548] macb 10090000.ethernet eth0: Cadence GEM rev 0x10070109 at 0x10090000 irq 7 (70:b3:d5:92:f2:f3)
-[ 1.077330] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
-[ 1.083069] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
-[ 1.089061] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
-[ 1.095485] ehci-pci: EHCI PCI platform driver
-[ 1.099947] ehci-platform: EHCI generic platform driver
-[ 1.105196] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
-[ 1.111286] ohci-pci: OHCI PCI platform driver
-[ 1.115742] ohci-platform: OHCI generic platform driver
-[ 1.121142] usbcore: registered new interface driver uas
-[ 1.126269] usbcore: registered new interface driver usb-storage
-[ 1.132331] mousedev: PS/2 mouse device common for all mice
-[ 1.137978] usbcore: registered new interface driver usbhid
-[ 1.143325] usbhid: USB HID core driver
-[ 1.148022] NET: Registered protocol family 10
-[ 1.152609] Segment Routing with IPv6
-[ 1.155571] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
-[ 1.161927] NET: Registered protocol family 17
-[ 1.165907] Key type dns_resolver registered
-[ 1.171694] Freeing unused kernel memory: 204K
-[ 1.175375] This architecture does not have kernel memory protection.
-[ 1.181792] Run /init as init process
- _ _
- | ||_|
- | | _ ____ _ _ _ _
- | || | _ \| | | |\ \/ /
- | || | | | | |_| |/ \
- |_||_|_| |_|\____|\_/\_/
-
- Busybox Rootfs
-
-Please press Enter to activate this console.
-/ #
--- /dev/null
+.. SPDX-License-Identifier: GPL-2.0+
+
+HiFive Unleashed
+================
+
+FU540-C000 RISC-V SoC
+---------------------
+The FU540-C000 is the world’s first 4+1 64-bit RISC-V SoC from SiFive.
+
+The HiFive Unleashed development platform is based on FU540-C000 and capable
+of running Linux.
+
+Mainline support
+----------------
+The support for following drivers are already enabled:
+
+1. SiFive UART Driver.
+2. SiFive PRCI Driver for clock.
+3. Cadence MACB ethernet driver for networking support.
+
+TODO:
+
+1. U-Boot expects the serial console device entry to be present under /chosen
+ DT node. Without a serial console U-Boot will panic. Example:
+
+.. code-block:: none
+
+ chosen {
+ stdout-path = "/soc/serial@10010000:115200";
+ };
+
+Building
+--------
+
+1. Add the RISC-V toolchain to your PATH.
+2. Setup ARCH & cross compilation enviornment variable:
+
+.. code-block:: none
+
+ export ARCH=riscv
+ export CROSS_COMPILE=<riscv64 toolchain prefix>
+
+3. make sifive_fu540_defconfig
+4. make
+
+Flashing
+--------
+
+The current U-Boot port is supported in S-mode only and loaded from DRAM.
+
+A prior stage (M-mode) firmware/bootloader (e.g OpenSBI or BBL) is required to
+load the u-boot.bin into memory and provide runtime services. The u-boot.bin
+can be given as a payload to the prior stage (M-mode) firmware/bootloader.
+
+The description of steps required to build the firmware is beyond the scope of
+this document. Please refer OpenSBI or BBL documenation.
+(Note: OpenSBI git repo is at https://github.com/riscv/opensbi.git)
+(Note: BBL git repo is at https://github.com/riscv/riscv-pk.git)
+
+Once the prior stage firmware/bootloader binary is generated, it should be
+copied to the first partition of the sdcard.
+
+.. code-block:: none
+
+ sudo dd if=<prior_stage_firmware_binary> of=/dev/disk2s1 bs=1024
+
+Booting
+-------
+Once you plugin the sdcard and power up, you should see the U-Boot prompt.
+
+Sample boot log from HiFive Unleashed board
+-------------------------------------------
+
+.. code-block:: none
+
+ U-Boot 2019.01-00019-gc7953536-dirty (Jan 22 2019 - 11:05:40 -0800)
+
+ CPU: rv64imafdc
+ Model: sifive,hifive-unleashed-a00
+ DRAM: 8 GiB
+ In: serial@10010000
+ Out: serial@10010000
+ Err: serial@10010000
+ Net:
+ Warning: ethernet@10090000 (eth0) using random MAC address - b6:75:4d:48:50:94
+ eth0: ethernet@10090000
+ Hit any key to stop autoboot: 0
+ => version
+ U-Boot 2019.01-00019-gc7953536-dirty (Jan 22 2019 - 11:05:40 -0800)
+
+ riscv64-linux-gcc.br_real (Buildroot 2018.11-rc2-00003-ga0787e9) 8.2.0
+ GNU ld (GNU Binutils) 2.31.1
+
+Now you can configure your networking, tftp server and use tftp boot method to
+load uImage.
+
+.. code-block:: none
+
+ => setenv ethaddr 70:B3:D5:92:F0:C2
+ => setenv ipaddr 10.196.157.189
+ => setenv serverip 10.11.143.218
+ => setenv gatewayip 10.196.156.1
+ => setenv netmask 255.255.252.0
+ => bdinfo
+ boot_params = 0x0000000000000000
+ DRAM bank = 0x0000000000000000
+ -> start = 0x0000000080000000
+ -> size = 0x0000000200000000
+ relocaddr = 0x00000000fff90000
+ reloc off = 0x000000007fd90000
+ ethaddr = 70:B3:D5:92:F0:C2
+ IP addr = 10.196.157.189
+ baudrate = 115200 bps
+ => tftpboot uImage
+ ethernet@10090000: PHY present at 0
+ ethernet@10090000: Starting autonegotiation...
+ ethernet@10090000: Autonegotiation complete
+ ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x3800)
+ Using ethernet@10090000 device
+ TFTP from server 10.11.143.218; our IP address is 10.196.157.189; sending through gateway 10.196.156.1
+ Filename 'uImage'.
+ Load address: 0x80200000
+ Loading: #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ ##########################################################
+ 2.5 MiB/s
+ done
+ Bytes transferred = 14939132 (e3f3fc hex)
+ => bootm 0x80200000 - 0x82200000
+ ## Booting kernel from Legacy Image at 80200000 ...
+ Image Name: Linux
+ Image Type: RISC-V Linux Kernel Image (uncompressed)
+ Data Size: 14939068 Bytes = 14.2 MiB
+ Load Address: 80200000
+ Entry Point: 80200000
+ Verifying Checksum ... OK
+ ## Flattened Device Tree blob at 82200000
+ Booting using the fdt blob at 0x82200000
+ Loading Kernel Image ... OK
+ Using Device Tree in place at 0000000082200000, end 0000000082205c69
+
+ Starting kernel ...
+
+ [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
+ [ 0.000000] Linux version 5.0.0-rc1-00020-g4b51f736 (atish@jedi-01) (gcc version 7.2.0 (GCC)) #262 SMP Mon Jan 21 17:39:27 PST 2019
+ [ 0.000000] initrd not found or empty - disabling initrd
+ [ 0.000000] Zone ranges:
+ [ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000ffffffff]
+ [ 0.000000] Normal [mem 0x0000000100000000-0x000027ffffffffff]
+ [ 0.000000] Movable zone start for each node
+ [ 0.000000] Early memory node ranges
+ [ 0.000000] node 0: [mem 0x0000000080200000-0x000000027fffffff]
+ [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000027fffffff]
+ [ 0.000000] software IO TLB: mapped [mem 0xfbfff000-0xfffff000] (64MB)
+ [ 0.000000] CPU with hartid=0 has a non-okay status of "masked"
+ [ 0.000000] CPU with hartid=0 has a non-okay status of "masked"
+ [ 0.000000] elf_hwcap is 0x112d
+ [ 0.000000] percpu: Embedded 15 pages/cpu @(____ptrval____) s29720 r0 d31720 u61440
+ [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975
+ [ 0.000000] Kernel command line: earlyprintk
+ [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
+ [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
+ [ 0.000000] Sorting __ex_table...
+ [ 0.000000] Memory: 8178760K/8386560K available (3309K kernel code, 248K rwdata, 872K rodata, 9381K init, 763K bss, 207800K reserved, 0K cma-reserved)
+ [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
+ [ 0.000000] rcu: Hierarchical RCU implementation.
+ [ 0.000000] rcu: RCU event tracing is enabled.
+ [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
+ [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
+ [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
+ [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
+ [ 0.000000] plic: mapped 53 interrupts to 4 (out of 9) handlers.
+ [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1]
+ [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
+ [ 0.000008] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns
+ [ 0.000221] Console: colour dummy device 80x25
+ [ 0.000902] printk: console [tty0] enabled
+ [ 0.000963] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
+ [ 0.001034] pid_max: default: 32768 minimum: 301
+ [ 0.001541] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
+ [ 0.001912] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
+ [ 0.003542] rcu: Hierarchical SRCU implementation.
+ [ 0.004347] smp: Bringing up secondary CPUs ...
+ [ 1.040259] CPU1: failed to come online
+ [ 2.080483] CPU2: failed to come online
+ [ 3.120699] CPU3: failed to come online
+ [ 3.120765] smp: Brought up 1 node, 1 CPU
+ [ 3.121923] devtmpfs: initialized
+ [ 3.124649] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
+ [ 3.124727] futex hash table entries: 1024 (order: 4, 65536 bytes)
+ [ 3.125346] random: get_random_u32 called from bucket_table_alloc+0x72/0x172 with crng_init=0
+ [ 3.125578] NET: Registered protocol family 16
+ [ 3.126400] sifive-u54-prci 10000000.prci: Registered U54 core clocks
+ [ 3.126649] sifive-gemgxl-mgmt 100a0000.cadence-gemgxl-mgmt: Registered clock switch 'cadence-gemgxl-mgmt'
+ [ 3.135572] vgaarb: loaded
+ [ 3.135858] SCSI subsystem initialized
+ [ 3.136193] usbcore: registered new interface driver usbfs
+ [ 3.136266] usbcore: registered new interface driver hub
+ [ 3.136348] usbcore: registered new device driver usb
+ [ 3.136446] pps_core: LinuxPPS API ver. 1 registered
+ [ 3.136484] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
+ [ 3.136575] PTP clock support registered
+ [ 3.137256] clocksource: Switched to clocksource riscv_clocksource
+ [ 3.142711] NET: Registered protocol family 2
+ [ 3.143322] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes)
+ [ 3.143634] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
+ [ 3.145799] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
+ [ 3.149121] TCP: Hash tables configured (established 65536 bind 65536)
+ [ 3.149591] UDP hash table entries: 4096 (order: 5, 131072 bytes)
+ [ 3.150094] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
+ [ 3.150781] NET: Registered protocol family 1
+ [ 3.230693] workingset: timestamp_bits=62 max_order=21 bucket_order=0
+ [ 3.241224] io scheduler mq-deadline registered
+ [ 3.241269] io scheduler kyber registered
+ [ 3.242143] sifive_gpio 10060000.gpio: SiFive GPIO chip registered 16 GPIOs
+ [ 3.242357] pwm-sifivem 10020000.pwm: Unable to find controller clock
+ [ 3.242439] pwm-sifivem 10021000.pwm: Unable to find controller clock
+ [ 3.243228] xilinx-pcie 2000000000.pci: PCIe Link is DOWN
+ [ 3.243289] xilinx-pcie 2000000000.pci: host bridge /soc/pci@2000000000 ranges:
+ [ 3.243360] xilinx-pcie 2000000000.pci: No bus range found for /soc/pci@2000000000, using [bus 00-ff]
+ [ 3.243447] xilinx-pcie 2000000000.pci: MEM 0x40000000..0x5fffffff -> 0x40000000
+ [ 3.243591] xilinx-pcie 2000000000.pci: PCI host bridge to bus 0000:00
+ [ 3.243636] pci_bus 0000:00: root bus resource [bus 00-ff]
+ [ 3.243676] pci_bus 0000:00: root bus resource [mem 0x40000000-0x5fffffff]
+ [ 3.276547] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
+ [ 3.277689] 10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 39, base_baud = 0) is a SiFive UART v0
+ [ 3.786963] printk: console [ttySIF0] enabled
+ [ 3.791504] 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 40, base_baud = 0) is a SiFive UART v0
+ [ 3.801251] sifive_spi 10040000.spi: mapped; irq=41, cs=1
+ [ 3.806362] m25p80 spi0.0: unrecognized JEDEC id bytes: 9d, 70, 19
+ [ 3.812084] m25p80: probe of spi0.0 failed with error -2
+ [ 3.817453] sifive_spi 10041000.spi: mapped; irq=42, cs=4
+ [ 3.823027] sifive_spi 10050000.spi: mapped; irq=43, cs=1
+ [ 3.828604] libphy: Fixed MDIO Bus: probed
+ [ 3.832623] macb: GEM doesn't support hardware ptp.
+ [ 3.837196] libphy: MACB_mii_bus: probed
+ [ 4.041156] Microsemi VSC8541 SyncE 10090000.ethernet-ffffffff:00: attached PHY driver [Microsemi VSC8541 SyncE] (mii_bus:phy_addr=10090000.ethernet-ffffffff:00, irq=POLL)
+ [ 4.055779] macb 10090000.ethernet eth0: Cadence GEM rev 0x10070109 at 0x10090000 irq 12 (70:b3:d5:92:f0:c2)
+ [ 4.065780] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
+ [ 4.072033] ehci-pci: EHCI PCI platform driver
+ [ 4.076521] usbcore: registered new interface driver usb-storage
+ [ 4.082843] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
+ [ 4.127465] mmc_spi spi2.0: SD/MMC host mmc0, no DMA, no WP, no poweroff
+ [ 4.133645] usbcore: registered new interface driver usbhid
+ [ 4.138980] usbhid: USB HID core driver
+ [ 4.143017] NET: Registered protocol family 17
+ [ 4.147885] pwm-sifivem 10020000.pwm: SiFive PWM chip registered 4 PWMs
+ [ 4.153945] pwm-sifivem 10021000.pwm: SiFive PWM chip registered 4 PWMs
+ [ 4.186407] Freeing unused kernel memory: 9380K
+ [ 4.190224] This architecture does not have kernel memory protection.
+ [ 4.196609] Run /init as init process
+ Starting logging: OK
+ Starting mdev...
+ [ 4.303785] mmc0: host does not support reading read-only switch, assuming write-enable
+ [ 4.311109] mmc0: new SDHC card on SPI
+ [ 4.317103] mmcblk0: mmc0:0000 SS08G 7.40 GiB
+ [ 4.386471] mmcblk0: p1 p2
+ sort: /sys/devices/platform/Fixed: No such file or directory
+ modprobe: can't change directory to '/lib/modules': No such file or directory
+ Initializing random[ 4.759075] random: dd: uninitialized urandom read (512 bytes read)
+ number generator... done.
+ Starting network...
+ udhcpc (v1.24.2) started
+ Sending discover...
+ Sending discover...
+ [ 7.927510] macb 10090000.ethernet eth0: link up (1000/Full)
+ Sending discover...
+ Sending select for 10.196.157.190...
+ Lease of 10.196.157.190 obtained, lease time 499743
+ deleting routers
+ adding dns 10.86.1.1
+ adding dns 10.86.2.1
+ /etc/init.d/S50dropbear
+ Starting dropbear sshd: [ 12.772393] random: dropbear: uninitialized urandom read (32 bytes read)
+ OK
+
+ Welcome to Buildroot
+ buildroot login:
projects / oweals / u-boot.git / commitdiff