#include <common.h>
#include <netdev.h>
+#include <ahci.h>
+#include <linux/mbus.h>
#include <asm/io.h>
#include <asm/pl310.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
+#include <sdhci.h>
#define DDR_BASE_CS_OFF(n) (0x0000 + ((n) << 3))
#define DDR_SIZE_CS_OFF(n) (0x0004 + ((n) << 3))
}
#endif
+#ifdef CONFIG_MV_SDHCI
+int board_mmc_init(bd_t *bis)
+{
+ mv_sdh_init(MVEBU_SDIO_BASE, 0, 0,
+ SDHCI_QUIRK_32BIT_DMA_ADDR | SDHCI_QUIRK_WAIT_SEND_CMD);
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_SCSI_AHCI_PLAT
+#define AHCI_VENDOR_SPECIFIC_0_ADDR 0xa0
+#define AHCI_VENDOR_SPECIFIC_0_DATA 0xa4
+
+#define AHCI_WINDOW_CTRL(win) (0x60 + ((win) << 4))
+#define AHCI_WINDOW_BASE(win) (0x64 + ((win) << 4))
+#define AHCI_WINDOW_SIZE(win) (0x68 + ((win) << 4))
+
+static void ahci_mvebu_mbus_config(void __iomem *base)
+{
+ const struct mbus_dram_target_info *dram;
+ int i;
+
+ dram = mvebu_mbus_dram_info();
+
+ for (i = 0; i < 4; i++) {
+ writel(0, base + AHCI_WINDOW_CTRL(i));
+ writel(0, base + AHCI_WINDOW_BASE(i));
+ writel(0, base + AHCI_WINDOW_SIZE(i));
+ }
+
+ for (i = 0; i < dram->num_cs; i++) {
+ const struct mbus_dram_window *cs = dram->cs + i;
+
+ writel((cs->mbus_attr << 8) |
+ (dram->mbus_dram_target_id << 4) | 1,
+ base + AHCI_WINDOW_CTRL(i));
+ writel(cs->base >> 16, base + AHCI_WINDOW_BASE(i));
+ writel(((cs->size - 1) & 0xffff0000),
+ base + AHCI_WINDOW_SIZE(i));
+ }
+}
+
+static void ahci_mvebu_regret_option(void __iomem *base)
+{
+ /*
+ * Enable the regret bit to allow the SATA unit to regret a
+ * request that didn't receive an acknowlegde and avoid a
+ * deadlock
+ */
+ writel(0x4, base + AHCI_VENDOR_SPECIFIC_0_ADDR);
+ writel(0x80, base + AHCI_VENDOR_SPECIFIC_0_DATA);
+}
+
+void scsi_init(void)
+{
+ printf("MVEBU SATA INIT\n");
+ ahci_mvebu_mbus_config((void __iomem *)MVEBU_SATA0_BASE);
+ ahci_mvebu_regret_option((void __iomem *)MVEBU_SATA0_BASE);
+ ahci_init((void __iomem *)MVEBU_SATA0_BASE);
+}
+#endif
+
#ifndef CONFIG_SYS_DCACHE_OFF
void enable_caches(void)
{
int mvebu_mbus_probe(struct mbus_win windows[], int count);
int mvebu_soc_family(void);
+int mv_sdh_init(unsigned long regbase, u32 max_clk, u32 min_clk, u32 quirks);
+
/*
* Highspeed SERDES PHY config init, ported from bin_hdr
* to mainline U-Boot
--- /dev/null
+/*
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __MACH_MVEBU_GPIO_H
+#define __MACH_MVEBU_GPIO_H
+
+/* Empty file - sdhci requires this. */
+
+#endif
#define MVEBU_EGIGA2_BASE (MVEBU_REGISTER(0x30000))
#define MVEBU_EGIGA3_BASE (MVEBU_REGISTER(0x34000))
#define MVEBU_REG_PCIE_BASE (MVEBU_REGISTER(0x40000))
+#define MVEBU_USB20_BASE (MVEBU_REGISTER(0x58000))
#define MVEBU_EGIGA0_BASE (MVEBU_REGISTER(0x70000))
#define MVEBU_EGIGA1_BASE (MVEBU_REGISTER(0x74000))
+#define MVEBU_SATA0_BASE (MVEBU_REGISTER(0xa8000))
+#define MVEBU_SDIO_BASE (MVEBU_REGISTER(0xd8000))
#define SDRAM_MAX_CS 4
#define SDRAM_ADDR_MASK 0xFF000000
--- /dev/null
+DB_88F6820_GP BOARD
+M: Stefan Roese <sr@denx.de>
+S: Maintained
+F: board/Marvell/db-88f6820-gp/
+F: include/configs/db-88f6820-gp.h
+F: configs/db-88f6820-gp_defconfig
writel(1 << i, mmio + HOST_IRQ_STAT);
- /* set irq mask (enables interrupts) */
- writel(DEF_PORT_IRQ, port_mmio + PORT_IRQ_MASK);
-
/* register linkup ports */
tmp = readl(port_mmio + PORT_SCR_STAT);
debug("SATA port %d status: 0x%x\n", i, tmp);
#include <mmc.h>
#include <sdhci.h>
+#if defined(CONFIG_FIXED_SDHCI_ALIGNED_BUFFER)
+void *aligned_buffer = (void *)CONFIG_FIXED_SDHCI_ALIGNED_BUFFER;
+#else
void *aligned_buffer;
+#endif
static void sdhci_reset(struct sdhci_host *host, u8 mask)
{
int trans_bytes = 0, is_aligned = 1;
u32 mask, flags, mode;
unsigned int time = 0, start_addr = 0;
- unsigned int retry = 10000;
int mmc_dev = mmc->block_dev.dev;
+ unsigned start = get_timer(0);
/* Timeout unit - ms */
static unsigned int cmd_timeout = CONFIG_SDHCI_CMD_DEFAULT_TIMEOUT;
memcpy(aligned_buffer, data->src, trans_bytes);
}
+#if defined(CONFIG_FIXED_SDHCI_ALIGNED_BUFFER)
+ /*
+ * Always use this bounce-buffer when
+ * CONFIG_FIXED_SDHCI_ALIGNED_BUFFER is defined
+ */
+ is_aligned = 0;
+ start_addr = (unsigned long)aligned_buffer;
+ if (data->flags != MMC_DATA_READ)
+ memcpy(aligned_buffer, data->src, trans_bytes);
+#endif
+
sdhci_writel(host, start_addr, SDHCI_DMA_ADDRESS);
mode |= SDHCI_TRNS_DMA;
#endif
flush_cache(start_addr, trans_bytes);
#endif
sdhci_writew(host, SDHCI_MAKE_CMD(cmd->cmdidx, flags), SDHCI_COMMAND);
+ start = get_timer(0);
do {
stat = sdhci_readl(host, SDHCI_INT_STATUS);
if (stat & SDHCI_INT_ERROR)
break;
- if (--retry == 0)
- break;
- } while ((stat & mask) != mask);
+ } while (((stat & mask) != mask) &&
+ (get_timer(start) < CONFIG_SDHCI_CMD_DEFAULT_TIMEOUT));
- if (retry == 0) {
+ if (get_timer(start) >= CONFIG_SDHCI_CMD_DEFAULT_TIMEOUT) {
if (host->quirks & SDHCI_QUIRK_BROKEN_R1B)
return 0;
else {
#include <asm/io.h>
#include <usb.h>
#include "ehci.h"
+#include <linux/mbus.h>
#include <asm/arch/cpu.h>
#if defined(CONFIG_KIRKWOOD)
/*
* USB 2.0 Bridge Address Decoding registers setup
*/
+#ifdef CONFIG_ARMADA_XP
+
+#define MVUSB0_BASE MVEBU_USB20_BASE
+
+/*
+ * Once all the older Marvell SoC's (Orion, Kirkwood) are converted
+ * to the common mvebu archticture including the mbus setup, this
+ * will be the only function needed to configure the access windows
+ */
+static void usb_brg_adrdec_setup(void)
+{
+ const struct mbus_dram_target_info *dram;
+ int i;
+
+ dram = mvebu_mbus_dram_info();
+
+ for (i = 0; i < 4; i++) {
+ wrl(USB_WINDOW_CTRL(i), 0);
+ wrl(USB_WINDOW_BASE(i), 0);
+ }
+
+ for (i = 0; i < dram->num_cs; i++) {
+ const struct mbus_dram_window *cs = dram->cs + i;
+
+ /* Write size, attributes and target id to control register */
+ wrl(USB_WINDOW_CTRL(i),
+ ((cs->size - 1) & 0xffff0000) | (cs->mbus_attr << 8) |
+ (dram->mbus_dram_target_id << 4) | 1);
+
+ /* Write base address to base register */
+ wrl(USB_WINDOW_BASE(i), cs->base);
+ }
+}
+#else
static void usb_brg_adrdec_setup(void)
{
int i;
wrl(USB_WINDOW_BASE(i), base);
}
}
+#endif
/*
* Create the appropriate control structures to manage
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ENV
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MMC
#define CONFIG_CMD_PING
+#define CONFIG_CMD_SCSI
#define CONFIG_CMD_SF
#define CONFIG_CMD_SPI
#define CONFIG_CMD_TFTPPUT
#define CONFIG_CMD_TIME
+#define CONFIG_CMD_USB
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
#define CONFIG_SPI_FLASH_STMICRO
+/*
+ * SDIO/MMC Card Configuration
+ */
+#define CONFIG_MMC
+#define CONFIG_MMC_SDMA
+#define CONFIG_GENERIC_MMC
+#define CONFIG_SDHCI
+#define CONFIG_MV_SDHCI
+#define CONFIG_SYS_MMC_BASE MVEBU_SDIO_BASE
+
+/*
+ * SATA/SCSI/AHCI configuration
+ */
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+
+/* Partition support */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+
+/* Additional FS support/configuration */
+#define CONFIG_SUPPORT_VFAT
+
+/* USB/EHCI configuration */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_MARVELL
+#define CONFIG_EHCI_IS_TDI
+
/* Environment in SPI NOR flash */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */
projects / oweals / u-boot.git / commitdiff