The boot mode pins are latched when the system reset is deasserted
and determine which device the system should load a boot image from.
+config DRAM_INIT
+ bool
+ default SPL_BUILD
+
+choice
+ prompt "DDR3 Frequency select"
+ depends on DRAM_INIT
+
+config DDR_FREQ_1600
+ bool "DDR3 1600"
+ depends on MACH_PH1_PRO4 || MACH_PH1_LD4
+
+config DDR_FREQ_1333
+ bool "DDR3 1333"
+ depends on MACH_PH1_LD4 || MACH_PH1_SLD8
+
+endchoice
+
+config DDR_FREQ
+ int
+ default 1333 if DDR_FREQ_1333
+ default 1600 if DDR_FREQ_1600
+
endmenu
DECLARE_GLOBAL_DATA_PTR;
gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
-#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
+#ifdef CONFIG_DRAM_INIT
led_write(B, 4, , );
{
obj-y += boot-mode.o
obj-$(CONFIG_BOARD_POSTCLK_INIT) += board_postclk_init.o bcu_init.o \
sbc_init.o sg_init.o pll_init.o clkrst_init.o pinctrl.o
-obj-$(CONFIG_SPL_BUILD) += pll_spectrum.o \
- umc_init.o
+obj-$(CONFIG_DRAM_INIT) += pll_spectrum.o umc_init.o
CONFIG_SDRAM1_SIZE / 0x08000000);
}
-#if CONFIG_DDR_FREQ != 1333 && CONFIG_DDR_FREQ != 1600
-#error Unsupported DDR Frequency.
-#endif
-
#if (CONFIG_SDRAM0_SIZE == 0x08000000 || CONFIG_SDRAM0_SIZE == 0x10000000) && \
(CONFIG_SDRAM1_SIZE == 0x08000000 || CONFIG_SDRAM1_SIZE == 0x10000000) && \
CONFIG_DDR_NUM_CH0 == 1 && CONFIG_DDR_NUM_CH1 == 1
obj-y += boot-mode.o
obj-$(CONFIG_BOARD_POSTCLK_INIT) += board_postclk_init.o sbc_init.o \
sg_init.o pll_init.o clkrst_init.o pinctrl.o
-obj-$(CONFIG_SPL_BUILD) += pll_spectrum.o \
- umc_init.o
+obj-$(CONFIG_DRAM_INIT) += pll_spectrum.o umc_init.o
CONFIG_SDRAM1_SIZE / 0x08000000);
}
-#if CONFIG_DDR_FREQ != 1600
-#error Unsupported DDR frequency.
-#endif
-
#if ((CONFIG_SDRAM0_SIZE == 0x20000000 && CONFIG_DDR_NUM_CH0 == 2) || \
(CONFIG_SDRAM0_SIZE == 0x10000000 && CONFIG_DDR_NUM_CH0 == 1)) && \
((CONFIG_SDRAM1_SIZE == 0x20000000 && CONFIG_DDR_NUM_CH1 == 2) || \
obj-y += boot-mode.o
obj-$(CONFIG_BOARD_POSTCLK_INIT) += board_postclk_init.o bcu_init.o \
sbc_init.o sg_init.o pll_init.o clkrst_init.o pinctrl.o
-obj-$(CONFIG_SPL_BUILD) += pll_spectrum.o \
- umc_init.o
+obj-$(CONFIG_DRAM_INIT) += pll_spectrum.o umc_init.o
CONFIG_SDRAM1_SIZE / 0x08000000);
}
-#if CONFIG_DDR_FREQ != 1333
-#error Unsupported DDR frequency.
-#endif
-
#if (CONFIG_SDRAM0_SIZE == 0x08000000 || CONFIG_SDRAM0_SIZE == 0x10000000) && \
(CONFIG_SDRAM1_SIZE == 0x08000000 || CONFIG_SDRAM1_SIZE == 0x10000000) && \
CONFIG_DDR_NUM_CH0 == 1 && CONFIG_DDR_NUM_CH1 == 1
#define CONFIG_DDR_NUM_CH0 1
#define CONFIG_DDR_NUM_CH1 1
-#define CONFIG_DDR_FREQ 1600
-
/*
* Memory Size & Mapping
*/
#define CONFIG_DDR_NUM_CH0 2
#define CONFIG_DDR_NUM_CH1 2
-#define CONFIG_DDR_FREQ 1600
-
#define CONFIG_UNIPHIER_SMP
/*
#define CONFIG_DDR_NUM_CH0 1
#define CONFIG_DDR_NUM_CH1 1
-#define CONFIG_DDR_FREQ 1333
-
/* #define CONFIG_DDR_STANDARD */
/*