#include <watchdog.h>
#include <stdio_dev.h>
#include <asm/u-boot-x86.h>
-#include <asm/processor.h>
+#include <asm/relocate.h>
#include <asm/init_helpers.h>
#include <asm/init_wrappers.h>
/*
* Breath some life into the board...
*
- * Initialize an SMC for serial comms, and carry out some hardware
- * tests.
+ * Getting the board up and running is a three-stage process:
+ * 1) Execute from Flash, SDRAM Uninitialised
+ * At this point, there is a limited amount of non-SDRAM memory
+ * (typically the CPU cache, but can also be SRAM or even a buffer of
+ * of some peripheral). This limited memory is used to hold:
+ * - The initial copy of the Global Data Structure
+ * - A temporary stack
+ * - A temporary x86 Global Descriptor Table
+ * - The pre-console buffer (if enabled)
*
- * The first part of initialization is running from Flash memory;
- * its main purpose is to initialize the RAM so that we
- * can relocate the monitor code to RAM.
+ * The following is performed during this phase of execution:
+ * - Core low-level CPU initialisation
+ * - Console initialisation
+ * - SDRAM initialisation
+ *
+ * 2) Execute from Flash, SDRAM Initialised
+ * At this point we copy Global Data from the initial non-SDRAM
+ * memory and set up the permanent stack in SDRAM. The CPU cache is no
+ * longer being used as temporary memory, so we can now fully enable
+ * it.
+ *
+ * The following is performed during this phase of execution:
+ * - Create final stack in SDRAM
+ * - Copy Global Data from temporary memory to SDRAM
+ * - Enabling of CPU cache(s),
+ * - Copying of U-Boot code and data from Flash to RAM
+ * - Clearing of the BSS
+ * - ELF relocation adjustments
+ *
+ * 3) Execute from SDRAM
+ * The following is performed during this phase of execution:
+ * - All remaining initialisation
*/
/*
- * All attempts to come up with a "common" initialization sequence
- * that works for all boards and architectures failed: some of the
- * requirements are just _too_ different. To get rid of the resulting
- * mess of board dependend #ifdef'ed code we now make the whole
- * initialization sequence configurable to the user.
- *
- * The requirements for any new initalization function is simple: it
- * receives a pointer to the "global data" structure as it's only
- * argument, and returns an integer return code, where 0 means
- * "continue" and != 0 means "fatal error, hang the system".
+ * The requirements for any new initalization function is simple: it is
+ * a function with no parameters which returns an integer return code,
+ * where 0 means "continue" and != 0 means "fatal error, hang the system"
*/
typedef int (init_fnc_t) (void);
-static int calculate_relocation_address(void);
-static int copy_gd_to_ram(void);
-
+/*
+ * init_sequence_f is the list of init functions which are run when U-Boot
+ * is executing from Flash with a limited 'C' environment. The following
+ * limitations must be considered when implementing an '_f' function:
+ * - 'static' variables are read-only
+ * - Global Data (gd->xxx) is read/write
+ * - Stack space is limited
+ *
+ * The '_f' sequence must, as a minimum, initialise SDRAM. It _should_
+ * also initialise the console (to provide early debug output)
+ */
init_fnc_t *init_sequence_f[] = {
cpu_init_f,
board_early_init_f,
NULL,
};
+/*
+ * init_sequence_f_r is the list of init functions which are run when
+ * U-Boot is executing from Flash with a semi-limited 'C' environment.
+ * The following limitations must be considered when implementing an
+ * '_f_r' function:
+ * - 'static' variables are read-only
+ * - Global Data (gd->xxx) is read/write
+ *
+ * The '_f_r' sequence must, as a minimum, copy U-Boot to RAM (if
+ * supported). It _should_, if possible, copy global data to RAM and
+ * initialise the CPU caches (to speed up the relocation process)
+ */
+init_fnc_t *init_sequence_f_r[] = {
+ copy_gd_to_ram_f_r,
+ init_cache_f_r,
+ copy_uboot_to_ram,
+ clear_bss,
+ do_elf_reloc_fixups,
+
+ NULL,
+};
+
+/*
+ * init_sequence_r is the list of init functions which are run when U-Boot
+ * is executing from RAM with a full 'C' environment. There are no longer
+ * any limitations which must be considered when implementing an '_r'
+ * function, (i.e.'static' variables are read/write)
+ *
+ * If not already done, the '_r' sequence must copy global data to RAM and
+ * (should) initialise the CPU caches.
+ */
init_fnc_t *init_sequence_r[] = {
+ set_reloc_flag_r,
init_bd_struct_r,
mem_malloc_init_r,
cpu_init_r,
}
}
-static int calculate_relocation_address(void)
-{
- ulong text_start = (ulong)&__text_start;
- ulong bss_end = (ulong)&__bss_end;
- ulong dest_addr;
-
- /*
- * NOTE: All destination address are rounded down to 16-byte
- * boundary to satisfy various worst-case alignment
- * requirements
- */
-
- /* Global Data is at top of available memory */
- dest_addr = gd->ram_size;
- dest_addr -= GENERATED_GBL_DATA_SIZE;
- dest_addr &= ~15;
- gd->new_gd_addr = dest_addr;
-
- /* GDT is below Global Data */
- dest_addr -= X86_GDT_SIZE;
- dest_addr &= ~15;
- gd->gdt_addr = dest_addr;
-
- /* Stack is below GDT */
- gd->start_addr_sp = dest_addr;
-
- /* U-Boot is below the stack */
- dest_addr -= CONFIG_SYS_STACK_SIZE;
- dest_addr -= (bss_end - text_start);
- dest_addr &= ~15;
- gd->relocaddr = dest_addr;
- gd->reloc_off = (dest_addr - text_start);
-
- return 0;
-}
-
-/* Perform all steps necessary to get RAM initialised ready for relocation */
void board_init_f(ulong boot_flags)
{
gd->flags = boot_flags;
do_init_loop(init_sequence_f);
/*
- * SDRAM is now initialised, U-Boot has been copied into SDRAM,
- * the BSS has been cleared etc. The final stack can now be setup
- * in SDRAM. Code execution will continue (momentarily) in Flash,
- * but with the stack in SDRAM and Global Data in temporary memory
+ * SDRAM and console are now initialised. The final stack can now
+ * be setup in SDRAM. Code execution will continue in Flash, but
+ * with the stack in SDRAM and Global Data in temporary memory
* (CPU cache)
*/
board_init_f_r_trampoline(gd->start_addr_sp);
void board_init_f_r(void)
{
- if (copy_gd_to_ram() != 0)
- hang();
-
- if (init_cache() != 0)
- hang();
-
- relocate_code(0, gd, 0);
-
- /* NOTREACHED - relocate_code() does not return */
- while (1)
- ;
-}
-
-static int copy_gd_to_ram(void)
-{
- gd_t *ram_gd;
+ do_init_loop(init_sequence_f_r);
/*
- * Global data is still in temporary memory (the CPU cache).
- * calculate_relocation_address() has set gd->new_gd_addr to
- * where the global data lives in RAM but getting it there
- * safely is a bit tricky due to the 'F-Segment Hack' that
- * we need to use for x86
+ * U-Boot has been copied into SDRAM, the BSS has been cleared etc.
+ * Transfer execution from Flash to RAM by calculating the address
+ * of the in-RAM copy of board_init_r() and calling it
*/
- ram_gd = (gd_t *)gd->new_gd_addr;
- memcpy((void *)ram_gd, gd, sizeof(gd_t));
+ (board_init_r + gd->reloc_off)(gd, gd->relocaddr);
- /*
- * Reload the Global Descriptor Table so FS points to the
- * in-RAM copy of Global Data (calculate_relocation_address()
- * has already calculated the in-RAM location of the GDT)
- */
- ram_gd->gd_addr = (ulong)ram_gd;
- init_gd(ram_gd, (u64 *)gd->gdt_addr);
-
- return 0;
+ /* NOTREACHED - board_init_r() does not return */
+ while (1)
+ ;
}
void board_init_r(gd_t *id, ulong dest_addr)
{
- gd->flags |= GD_FLG_RELOC;
-
- /* compiler optimization barrier needed for GCC >= 3.4 */
- __asm__ __volatile__("" : : : "memory");
-
do_init_loop(init_sequence_r);
/* main_loop() can return to retry autoboot, if so just run it again. */
#include <ide.h>
#include <serial.h>
#include <status_led.h>
+#include <asm/processor.h>
#include <asm/u-boot-x86.h>
#include <asm/init_helpers.h>
return 0;
}
+int calculate_relocation_address(void)
+{
+ ulong text_start = (ulong)&__text_start;
+ ulong bss_end = (ulong)&__bss_end;
+ ulong dest_addr;
+
+ /*
+ * NOTE: All destination address are rounded down to 16-byte
+ * boundary to satisfy various worst-case alignment
+ * requirements
+ */
+
+ /* Global Data is at top of available memory */
+ dest_addr = gd->ram_size;
+ dest_addr -= GENERATED_GBL_DATA_SIZE;
+ dest_addr &= ~15;
+ gd->new_gd_addr = dest_addr;
+
+ /* GDT is below Global Data */
+ dest_addr -= X86_GDT_SIZE;
+ dest_addr &= ~15;
+ gd->gdt_addr = dest_addr;
+
+ /* Stack is below GDT */
+ gd->start_addr_sp = dest_addr;
+
+ /* U-Boot is below the stack */
+ dest_addr -= CONFIG_SYS_STACK_SIZE;
+ dest_addr -= (bss_end - text_start);
+ dest_addr &= ~15;
+ gd->relocaddr = dest_addr;
+ gd->reloc_off = (dest_addr - text_start);
+
+ return 0;
+}
+
+int copy_gd_to_ram_f_r(void)
+{
+ gd_t *ram_gd;
+
+ /*
+ * Global data is still in temporary memory (the CPU cache).
+ * calculate_relocation_address() has set gd->new_gd_addr to
+ * where the global data lives in RAM but getting it there
+ * safely is a bit tricky due to the 'F-Segment Hack' that
+ * we need to use for x86
+ */
+ ram_gd = (gd_t *)gd->new_gd_addr;
+ memcpy((void *)ram_gd, gd, sizeof(gd_t));
+
+ /*
+ * Reload the Global Descriptor Table so FS points to the
+ * in-RAM copy of Global Data (calculate_relocation_address()
+ * has already calculated the in-RAM location of the GDT)
+ */
+ ram_gd->gd_addr = (ulong)ram_gd;
+ init_gd(ram_gd, (u64 *)gd->gdt_addr);
+
+ return 0;
+}
+
+int init_cache_f_r(void)
+{
+ /* Initialise the CPU cache(s) */
+ return init_cache();
+}
+
+int set_reloc_flag_r(void)
+{
+ gd->flags = GD_FLG_RELOC;
+
+ return 0;
+}
+
int mem_malloc_init_r(void)
{
mem_malloc_init(((gd->relocaddr - CONFIG_SYS_MALLOC_LEN)+3)&~3,
projects / oweals / u-boot.git / commitdiff