config TARGET_ATSTK1006
bool "Support atstk1006"
-config TARGET_FAVR_32_EZKIT
- bool "Support favr-32-ezkit"
-
config TARGET_GRASSHOPPER
bool "Support grasshopper"
source "board/atmel/atngw100/Kconfig"
source "board/atmel/atngw100mkii/Kconfig"
source "board/atmel/atstk1000/Kconfig"
-source "board/earthlcd/favr-32-ezkit/Kconfig"
source "board/in-circuit/grasshopper/Kconfig"
source "board/mimc/mimc200/Kconfig"
source "board/miromico/hammerhead/Kconfig"
+++ /dev/null
-if TARGET_FAVR_32_EZKIT
-
-config SYS_BOARD
- default "favr-32-ezkit"
-
-config SYS_VENDOR
- default "earthlcd"
-
-config SYS_SOC
- default "at32ap700x"
-
-config SYS_CONFIG_NAME
- default "favr-32-ezkit"
-
-endif
+++ /dev/null
-FAVR-32-EZKIT BOARD
-#M: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
-S: Orphan (since 2014-06)
-F: board/earthlcd/favr-32-ezkit/
-F: include/configs/favr-32-ezkit.h
-F: configs/favr-32-ezkit_defconfig
+++ /dev/null
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# Copyright (C) 2008 Atmel Corporation
-#
-# SPDX-License-Identifier: GPL-2.0+
-
-obj-y := favr-32-ezkit.o flash.o
+++ /dev/null
-/*
- * Copyright (C) 2008 Atmel Corporation
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#include <common.h>
-#include <netdev.h>
-
-#include <asm/io.h>
-#include <asm/sdram.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/hmatrix.h>
-#include <asm/arch/mmu.h>
-#include <asm/arch/portmux.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = {
- {
- .virt_pgno = CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT,
- .nr_pages = CONFIG_SYS_FLASH_SIZE >> MMU_PAGE_SHIFT,
- .phys = (CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT)
- | MMU_VMR_CACHE_NONE,
- }, {
- .virt_pgno = CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT,
- .nr_pages = EBI_SDRAM_SIZE >> MMU_PAGE_SHIFT,
- .phys = (CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT)
- | MMU_VMR_CACHE_WRBACK,
- },
-};
-
-static const struct sdram_config sdram_config = {
- /* MT48LC4M32B2P-6 (16 MB) */
- .data_bits = SDRAM_DATA_32BIT,
- .row_bits = 12,
- .col_bits = 8,
- .bank_bits = 2,
- .cas = 3,
- .twr = 2,
- .trc = 7,
- .trp = 2,
- .trcd = 2,
- .tras = 5,
- .txsr = 5,
- /* 15.6 us */
- .refresh_period = (156 * (SDRAMC_BUS_HZ / 1000)) / 10000,
-};
-
-int board_early_init_f(void)
-{
- /* Enable SDRAM in the EBI mux */
- hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE));
-
- portmux_enable_ebi(32, 23, 0, PORTMUX_DRIVE_HIGH);
-
- sdram_init(uncached(EBI_SDRAM_BASE), &sdram_config);
-
- portmux_enable_usart3(PORTMUX_DRIVE_MIN);
-#if defined(CONFIG_MACB)
- portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
-#endif
-#if defined(CONFIG_MMC)
- portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW);
-#endif
-
- return 0;
-}
-
-int board_early_init_r(void)
-{
- gd->bd->bi_phy_id[0] = 0x01;
- return 0;
-}
-
-#if defined(CONFIG_MACB) && defined(CONFIG_CMD_NET)
-int board_eth_init(bd_t *bi)
-{
- return macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0,
- bi->bi_phy_id[0]);
-}
-#endif
+++ /dev/null
-/*
- * Copyright (C) 2008 Atmel Corporation
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#include <common.h>
-
-#ifdef CONFIG_FAVR32_EZKIT_EXT_FLASH
-#include <asm/arch/cacheflush.h>
-#include <asm/io.h>
-#include <asm/sections.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-flash_info_t flash_info[1];
-
-static void flash_identify(uint16_t *flash, flash_info_t *info)
-{
- unsigned long flags;
-
- flags = disable_interrupts();
-
- dcache_flush_unlocked();
-
- writew(0xaa, flash + 0x555);
- writew(0x55, flash + 0xaaa);
- writew(0x90, flash + 0x555);
- info->flash_id = readl(flash);
- writew(0xff, flash);
-
- readw(flash);
-
- if (flags)
- enable_interrupts();
-}
-
-unsigned long flash_init(void)
-{
- unsigned long addr;
- unsigned int i;
-
- flash_info[0].size = CONFIG_SYS_FLASH_SIZE;
- flash_info[0].sector_count = 135;
-
- flash_identify(uncached((void *)CONFIG_SYS_FLASH_BASE), &flash_info[0]);
-
- for (i = 0, addr = 0; i < 8; i++, addr += 0x2000)
- flash_info[0].start[i] = addr;
- for (; i < flash_info[0].sector_count; i++, addr += 0x10000)
- flash_info[0].start[i] = addr;
-
- return CONFIG_SYS_FLASH_SIZE;
-}
-
-void flash_print_info(flash_info_t *info)
-{
- printf("Flash: Vendor ID: 0x%02lx, Product ID: 0x%02lx\n",
- info->flash_id >> 16, info->flash_id & 0xffff);
- printf("Size: %ld MB in %d sectors\n",
- info->size >> 10, info->sector_count);
-}
-
-int flash_erase(flash_info_t *info, int s_first, int s_last)
-{
- unsigned long flags;
- unsigned long start_time;
- uint16_t *fb, *sb;
- unsigned int i;
- int ret;
- uint16_t status;
-
- if ((s_first < 0) || (s_first > s_last)
- || (s_last >= info->sector_count)) {
- puts("Error: first and/or last sector out of range\n");
- return ERR_INVAL;
- }
-
- for (i = s_first; i < s_last; i++)
- if (info->protect[i]) {
- printf("Error: sector %d is protected\n", i);
- return ERR_PROTECTED;
- }
-
- fb = (uint16_t *)uncached(info->start[0]);
-
- dcache_flush_unlocked();
-
- for (i = s_first; (i <= s_last) && !ctrlc(); i++) {
- printf("Erasing sector %3d...", i);
-
- sb = (uint16_t *)uncached(info->start[i]);
-
- flags = disable_interrupts();
-
- start_time = get_timer(0);
-
- /* Unlock sector */
- writew(0xaa, fb + 0x555);
- writew(0x70, sb);
-
- /* Erase sector */
- writew(0xaa, fb + 0x555);
- writew(0x55, fb + 0xaaa);
- writew(0x80, fb + 0x555);
- writew(0xaa, fb + 0x555);
- writew(0x55, fb + 0xaaa);
- writew(0x30, sb);
-
- /* Wait for completion */
- ret = ERR_OK;
- do {
- /* TODO: Timeout */
- status = readw(sb);
- } while ((status != 0xffff) && !(status & 0x28));
-
- writew(0xf0, fb);
-
- /*
- * Make sure the command actually makes it to the bus
- * before we re-enable interrupts.
- */
- readw(fb);
-
- if (flags)
- enable_interrupts();
-
- if (status != 0xffff) {
- printf("Flash erase error at address 0x%p: 0x%02x\n",
- sb, status);
- ret = ERR_PROG_ERROR;
- break;
- }
- }
-
- if (ctrlc())
- printf("User interrupt!\n");
-
- return ERR_OK;
-}
-
-int write_buff(flash_info_t *info, uchar *src,
- ulong addr, ulong count)
-{
- unsigned long flags;
- uint16_t *base, *p, *s, *end;
- uint16_t word, status, status1;
- int ret = ERR_OK;
-
- if (addr < info->start[0]
- || (addr + count) > (info->start[0] + info->size)
- || (addr + count) < addr) {
- puts("Error: invalid address range\n");
- return ERR_INVAL;
- }
-
- if (addr & 1 || count & 1 || (unsigned int)src & 1) {
- puts("Error: misaligned source, destination or count\n");
- return ERR_ALIGN;
- }
-
- base = (uint16_t *)uncached(info->start[0]);
- end = (uint16_t *)uncached(addr + count);
-
- flags = disable_interrupts();
-
- dcache_flush_unlocked();
- sync_write_buffer();
-
- for (p = (uint16_t *)uncached(addr), s = (uint16_t *)src;
- p < end && !ctrlc(); p++, s++) {
- word = *s;
-
- writew(0xaa, base + 0x555);
- writew(0x55, base + 0xaaa);
- writew(0xa0, base + 0x555);
- writew(word, p);
-
- sync_write_buffer();
-
- /* Wait for completion */
- status1 = readw(p);
- do {
- /* TODO: Timeout */
- status = status1;
- status1 = readw(p);
- } while (((status ^ status1) & 0x40) /* toggled */
- && !(status1 & 0x28)); /* error bits */
-
- /*
- * We'll need to check once again for toggle bit
- * because the toggle bit may stop toggling as I/O5
- * changes to "1" (ref at49bv642.pdf p9)
- */
- status1 = readw(p);
- status = readw(p);
- if ((status ^ status1) & 0x40) {
- printf("Flash write error at address 0x%p: "
- "0x%02x != 0x%02x\n",
- p, status,word);
- ret = ERR_PROG_ERROR;
- writew(0xf0, base);
- readw(base);
- break;
- }
-
- writew(0xf0, base);
- readw(base);
- }
-
- if (flags)
- enable_interrupts();
-
- return ret;
-}
-
-#endif /* CONFIG_FAVR32_EZKIT_EXT_FLASH */
+++ /dev/null
-CONFIG_AVR32=y
-CONFIG_CMD_NET=y
-CONFIG_TARGET_FAVR_32_EZKIT=y
-CONFIG_AUTOBOOT_KEYED=y
-CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
-CONFIG_AUTOBOOT_DELAY_STR="d"
-CONFIG_AUTOBOOT_STOP_STR=" "
+++ /dev/null
-/*
- * Copyright (C) 2008 Atmel Corporation
- *
- * Configuration settings for the Favr-32 EarthLCD LCD kit.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/hardware.h>
-
-#define CONFIG_AT32AP
-#define CONFIG_AT32AP7000
-#define CONFIG_FAVR32_EZKIT
-
-#define CONFIG_FAVR32_EZKIT_EXT_FLASH
-
-/*
- * Set up the PLL to run at 140 MHz, the CPU to run at the PLL
- * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the
- * PLL frequency.
- * (CONFIG_SYS_OSC0_HZ * CONFIG_SYS_PLL0_MUL) / CONFIG_SYS_PLL0_DIV = PLL MHz
- */
-#define CONFIG_PLL
-#define CONFIG_SYS_POWER_MANAGER
-#define CONFIG_SYS_OSC0_HZ 20000000
-#define CONFIG_SYS_PLL0_DIV 1
-#define CONFIG_SYS_PLL0_MUL 7
-#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16
-/*
- * Set the CPU running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_CPU) = CPU MHz
- */
-#define CONFIG_SYS_CLKDIV_CPU 0
-/*
- * Set the HSB running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_HSB) = HSB MHz
- */
-#define CONFIG_SYS_CLKDIV_HSB 1
-/*
- * Set the PBA running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_PBA) = PBA MHz
- */
-#define CONFIG_SYS_CLKDIV_PBA 2
-/*
- * Set the PBB running at:
- * PLL / (2^CONFIG_SYS_CLKDIV_PBB) = PBB MHz
- */
-#define CONFIG_SYS_CLKDIV_PBB 1
-
-/* Reserve VM regions for SDRAM and NOR flash */
-#define CONFIG_SYS_NR_VM_REGIONS 2
-
-/*
- * The PLLOPT register controls the PLL like this:
- * icp = PLLOPT<2>
- * ivco = PLLOPT<1:0>
- *
- * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
- */
-#define CONFIG_SYS_PLL0_OPT 0x04
-
-#define CONFIG_USART_BASE ATMEL_BASE_USART3
-#define CONFIG_USART_ID 3
-
-/* User serviceable stuff */
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_STACKSIZE (2048)
-
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_BOOTARGS \
- "root=/dev/mtdblock1 rootfstype=jffs fbmem=1800k"
-
-#define CONFIG_BOOTCOMMAND \
- "fsload; bootm $(fileaddr)"
-
-#define CONFIG_BOOTDELAY 1
-
-/*
- * After booting the board for the first time, new ethernet addresses
- * should be generated and assigned to the environment variables
- * "ethaddr" and "eth1addr". This is normally done during production.
- */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MMC
-
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_SOURCE
-#undef CONFIG_CMD_XIMG
-
-#define CONFIG_ATMEL_USART
-#define CONFIG_MACB
-#define CONFIG_PORTMUX_PIO
-#define CONFIG_SYS_NR_PIOS 5
-#define CONFIG_SYS_HSDRAMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#define CONFIG_GENERIC_MMC
-
-#define CONFIG_SYS_DCACHE_LINESZ 32
-#define CONFIG_SYS_ICACHE_LINESZ 32
-
-#define CONFIG_NR_DRAM_BANKS 1
-
-/* External flash on Favr-32 */
-#if 0
-#define CONFIG_SYS_FLASH_CFI 1
-#define CONFIG_FLASH_CFI_DRIVER 1
-#endif
-
-#define CONFIG_SYS_FLASH_BASE 0x00000000
-#define CONFIG_SYS_FLASH_SIZE 0x800000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_MAX_FLASH_SECT 135
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_TEXT_BASE 0x00000000
-
-#define CONFIG_SYS_INTRAM_BASE INTERNAL_SRAM_BASE
-#define CONFIG_SYS_INTRAM_SIZE INTERNAL_SRAM_SIZE
-#define CONFIG_SYS_SDRAM_BASE EBI_SDRAM_BASE
-
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SIZE 65536
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
-
-#define CONFIG_SYS_MALLOC_LEN (256*1024)
-
-/* Allow 4MB for the kernel run-time image */
-#define CONFIG_SYS_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000)
-#define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024)
-
-/* Other configuration settings that shouldn't have to change all that often */
-#define CONFIG_SYS_PROMPT "U-Boot> "
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-
-#define CONFIG_SYS_MEMTEST_START EBI_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x700000)
-#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
-
-#endif /* __CONFIG_H */
projects / oweals / u-boot.git / commitdiff