--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk3399-u-boot.dtsi"
+
+#ifdef CONFIG_TARGET_PUMA_RK3399_RAM_DDR3_1333
+#include "rk3399-sdram-ddr3-1333.dtsi"
+#endif
+#ifdef CONFIG_TARGET_PUMA_RK3399_RAM_DDR3_1600
+#include "rk3399-sdram-ddr3-1600.dtsi"
+#endif
+#ifdef CONFIG_TARGET_PUMA_RK3399_RAM_DDR3_1866
+#include "rk3399-sdram-ddr3-1866.dtsi"
+#endif
+
+/ {
+ config {
+ u-boot,spl-payload-offset = <0x40000>; /* @ 256KB */
+ u-boot,mmc-env-offset = <0x4000>; /* @ 16KB */
+ u-boot,efi-partition-entries-offset = <0x200000>; /* 2MB */
+ u-boot,boot-led = "module_led";
+ sysreset-gpio = <&gpio1 RK_PA6 GPIO_ACTIVE_HIGH>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ u-boot,spl-boot-order = \
+ "same-as-spl", &norflash, &sdhci, &sdmmc;
+ };
+
+ aliases {
+ spi0 = &spi1;
+ spi1 = &spi5;
+ };
+
+ /*
+ * The Qseven BIOS_DISABLE signal on the RK3399-Q7 keeps the on-module
+ * eMMC and SPI flash powered-down initially (in fact it keeps the
+ * reset signal asserted). Even though it is an enable signal, we
+ * model this as a regulator.
+ */
+ bios_enable: bios_enable {
+ compatible = "regulator-fixed";
+ u-boot,dm-pre-reloc;
+ regulator-name = "bios_enable";
+ enable-active-high;
+ gpio = <&gpio3 RK_PD5 GPIO_ACTIVE_LOW>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+};
+
+&gpio1 {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio3 {
+ u-boot,dm-pre-reloc;
+};
+
+&norflash {
+ u-boot,dm-pre-reloc;
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Theobroma Systems Design und Consulting GmbH
+ */
+
+/dts-v1/;
+#include "rk3399-puma.dtsi"
+
+/ {
+ model = "Theobroma Systems RK3399-Q7 SoM";
+ compatible = "tsd,rk3399-puma-haikou", "rockchip,rk3399";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ pinctrl-0 = <&led_pin_module>, <&led_sd_haikou>;
+
+ sd-card-led {
+ label = "sd_card_led";
+ gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ };
+ };
+
+ i2s0-sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "Haikou,I2S-codec";
+ simple-audio-card,mclk-fs = <512>;
+
+ simple-audio-card,codec {
+ clocks = <&sgtl5000_clk>;
+ sound-dai = <&sgtl5000>;
+ };
+
+ simple-audio-card,cpu {
+ bitclock-master;
+ frame-master;
+ sound-dai = <&i2s0>;
+ };
+ };
+
+ sgtl5000_clk: sgtl5000-oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ };
+
+ dc_12v: dc-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc3v3_baseboard: vcc3v3-baseboard {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_baseboard";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vcc5v0_baseboard: vcc5v0-baseboard {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_baseboard";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vcc5v0_otg: vcc5v0-otg-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_vbus_drv>;
+ regulator-name = "vcc5v0_otg";
+ regulator-always-on;
+ };
+
+ vdda_codec: vdda-codec {
+ compatible = "regulator-fixed";
+ regulator-name = "vdda_codec";
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_baseboard>;
+ };
+
+ vddd_codec: vddd-codec {
+ compatible = "regulator-fixed";
+ regulator-name = "vddd_codec";
+ regulator-boot-on;
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <1600000>;
+ vin-supply = <&vcc5v0_baseboard>;
+ };
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c3>;
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+};
+
+&i2c2 {
+ status = "okay";
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ i2c-scl-rising-time-ns = <450>;
+ i2c-scl-falling-time-ns = <15>;
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&sgtl5000_clk>;
+ #sound-dai-cells = <0>;
+ VDDA-supply = <&vdda_codec>;
+ VDDIO-supply = <&vdda_codec>;
+ VDDD-supply = <&vddd_codec>;
+ status = "okay";
+ };
+};
+
+&i2c6 {
+ status = "okay";
+ clock-frequency = <400000>;
+};
+
+&pcie_phy {
+ status = "okay";
+};
+
+&pcie0 {
+ ep-gpios = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
+ num-lanes = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_clkreqn_cpm>;
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&haikou_pin_hog>;
+
+ hog {
+ haikou_pin_hog: haikou-pin-hog {
+ rockchip,pins =
+ /* LID_BTN */
+ <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* BATLOW# */
+ <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* SLP_BTN# */
+ <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* BIOS_DISABLE# */
+ <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ leds {
+ led_sd_haikou: led-sd-gpio {
+ rockchip,pins =
+ <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb2 {
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins =
+ <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ max-frequency = <150000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+ vmmc-supply = <&vcc3v3_baseboard>;
+ status = "okay";
+};
+
+&spi5 {
+ status = "okay";
+};
+
+&tcphy0 {
+ status = "okay";
+};
+
+&u2phy0 {
+ status = "okay";
+};
+
+&usbdrd3_0 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&u2phy0_host {
+ phy-supply = <&vcc5v0_otg>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-
-#include "rk3399-u-boot.dtsi"
-/ {
- config {
- u-boot,spl-payload-offset = <0x40000>; /* @ 256KB */
- u-boot,mmc-env-offset = <0x4000>; /* @ 16KB */
- u-boot,efi-partition-entries-offset = <0x200000>; /* 2MB */
- u-boot,boot-led = "module_led";
- sysreset-gpio = <&gpio1 RK_PA6 GPIO_ACTIVE_HIGH>;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- u-boot,spl-boot-order = \
- "same-as-spl", &norflash, &sdhci, &sdmmc;
- };
-
- aliases {
- spi0 = &spi1;
- spi1 = &spi5;
- };
-
- /*
- * The Qseven BIOS_DISABLE signal on the RK3399-Q7 keeps the on-module
- * eMMC and SPI flash powered-down initially (in fact it keeps the
- * reset signal asserted). Even though it is an enable signal, we
- * model this as a regulator.
- */
- bios_enable: bios_enable {
- compatible = "regulator-fixed";
- u-boot,dm-pre-reloc;
- regulator-name = "bios_enable";
- enable-active-high;
- gpio = <&gpio3 RK_PD5 GPIO_ACTIVE_LOW>;
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-};
-
-&gpio1 {
- u-boot,dm-pre-reloc;
-};
-
-&gpio3 {
- u-boot,dm-pre-reloc;
-};
-
-&norflash {
- u-boot,dm-pre-reloc;
-};
projects / oweals / u-boot.git / commitdiff