control registers. This behavior won't affect the
correctnessof 10/100 link speed update.
- CONFIG_SMC911X
- Support for SMSC's LAN911x and LAN921x chips
-
- CONFIG_SMC911X_BASE
- Define this to hold the physical address
- of the device (I/O space)
-
- CONFIG_SMC911X_32_BIT
- Define this if data bus is 32 bits
-
- CONFIG_SMC911X_16_BIT
- Define this if data bus is 16 bits. If your processor
- automatically converts one 32 bit word to two 16 bit
- words you may also try CONFIG_SMC911X_32_BIT.
-
CONFIG_SH_ETHER
Support for Renesas on-chip Ethernet controller
* Routine: board_eth_init
* Description: initialize module and base-board Ethernet chips
*/
+#define SB_T35_SMC911X_BASE (CONFIG_SMC911X_BASE + SZ_16M)
int board_eth_init(bd_t *bis)
{
int rc = 0, rc1 = 0;
if (rc1)
printf("No MAC address found! ");
- rc1 = cl_omap3_smc911x_init(0, 5, CM_T3X_SMC911X_BASE,
+ rc1 = cl_omap3_smc911x_init(0, 5, CONFIG_SMC911X_BASE,
cm_t3x_reset_net_chip, -EINVAL);
if (rc1 > 0)
rc++;
CONFIG_DOS_PARTITION=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_MTD_NOR_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0xB6080000
+CONFIG_SMC911X_32_BIT=y
CONFIG_BAUDRATE=38400
CONFIG_SCIF_CONSOLE=y
CONFIG_USE_PRIVATE_LIBGCC=y
CONFIG_MMC_DW=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_S5P=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x5000000
CONFIG_SOUND=y
CONFIG_I2S=y
CONFIG_I2S_SAMSUNG=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x18000000
CONFIG_BAUDRATE=38400
CONFIG_SCIF_CONSOLE=y
CONFIG_LED_STATUS_BOOT=0
CONFIG_MMC_OMAP_HS=y
CONFIG_NAND=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x2D000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_USB=y
CONFIG_MMC_OMAP_HS=y
CONFIG_NAND=y
CONFIG_SPL_NAND_SIMPLE=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x2C000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
CONFIG_OF_LIBFDT=y
+CONFIG_NETDEVICES=y
# CONFIG_SPL_EFI_PARTITION is not set
CONFIG_SPL_PARTITION_UUIDS=y
CONFIG_MMC_OMAP_HS=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x2C000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_USB=y
CONFIG_NAND=y
CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
CONFIG_SPL_NAND_SIMPLE=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x2C000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_FAT_WRITE=y
CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
CONFIG_SPL_NAND_SIMPLE=y
CONFIG_MTD_UBI_FASTMAP=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x2C000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_FAT_WRITE=y
CONFIG_ENV_IS_IN_EEPROM=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0xa8000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_ENV_IS_IN_EEPROM=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0xa8000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_ENV_IS_IN_FLASH=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x10000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_SCIF_CONSOLE=y
# CONFIG_FAT_WRITE is not set
CONFIG_OF_LIBFDT=y
# CONFIG_MMC is not set
CONFIG_NAND=y
CONFIG_NAND_MXC=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0xB6000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_NAND=y
CONFIG_NAND_MXC=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0xB6000000
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_NAND=y
CONFIG_NAND_MXC=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0xF4000000
CONFIG_OF_LIBFDT=y
CONFIG_MMC_DW=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_S5P=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x5000000
CONFIG_DM_PMIC=y
CONFIG_PMIC_S2MPS11=y
CONFIG_DM_REGULATOR=y
CONFIG_NAND=y
CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
CONFIG_SPL_NAND_SIMPLE=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x2C000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_DM_SERIAL=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000
CONFIG_SPL_NAND_SIMPLE=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x08000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_USB=y
CONFIG_NAND=y
CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
CONFIG_SPL_NAND_SIMPLE=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x2C000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_USB=y
CONFIG_FAT_WRITE=y
CONFIG_BCH=y
CONFIG_OF_LIBFDT=y
+CONFIG_NETDEVICES=y
CONFIG_MMC_OMAP_HS=y
CONFIG_NAND=y
CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x08000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_FAT_WRITE=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_GIGADEVICE=y
CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x5000000
CONFIG_DM_PMIC=y
CONFIG_PMIC_TPS65090=y
CONFIG_DM_REGULATOR=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_GIGADEVICE=y
CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x5000000
CONFIG_DM_PMIC=y
CONFIG_PMIC_TPS65090=y
CONFIG_DM_REGULATOR=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_GIGADEVICE=y
CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x5000000
CONFIG_DM_PMIC=y
CONFIG_DM_PMIC_MAX77686=y
CONFIG_DM_REGULATOR=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_GIGADEVICE=y
CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x5000000
CONFIG_DM_PMIC=y
CONFIG_DM_REGULATOR=y
CONFIG_EXYNOS_SPI=y
CONFIG_CMD_MTDPARTS=y
CONFIG_ENV_IS_IN_ONENAND=y
# CONFIG_MMC is not set
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x98800300
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_SDMA=y
CONFIG_MMC_SDHCI_S5P=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x5000000
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_GIGADEVICE=y
CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x5000000
CONFIG_DM_PMIC=y
CONFIG_DM_PMIC_MAX77686=y
CONFIG_PMIC_S5M8767=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_GIGADEVICE=y
CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x5000000
CONFIG_DM_PMIC=y
CONFIG_DM_PMIC_MAX77686=y
CONFIG_PMIC_S5M8767=y
CONFIG_NAND_OMAP_GPMC_PREFETCH=y
CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
CONFIG_SPL_NAND_SIMPLE=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x2C000000
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_SYS_NAND_DENALI_64BIT=y
CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES=8
CONFIG_SPL_NAND_DENALI=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_32_BIT=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_GENERIC=y
CONFIG_SYS_NAND_DENALI_64BIT=y
CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES=8
CONFIG_SPL_NAND_DENALI=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x0
+CONFIG_SMC911X_32_BIT=y
CONFIG_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_EHCI_HCD=y
CONFIG_NAND_DENALI_DT=y
CONFIG_SYS_NAND_DENALI_64BIT=y
CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES=8
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x0
+CONFIG_SMC911X_32_BIT=y
CONFIG_SYSRESET=y
CONFIG_SYSRESET_PSCI=y
CONFIG_USB=y
CONFIG_CMD_FAT=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_MTD_NOR_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x00000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_CMD_UBI=y
# CONFIG_CMD_UBIFS is not set
CONFIG_ENV_IS_IN_ONENAND=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x00000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_CMD_FAT=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_MTD_NOR_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x00000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_CMD_UBI=y
# CONFIG_CMD_UBIFS is not set
CONFIG_ENV_IS_IN_ONENAND=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x00000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_DM=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x018000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_DM_SERIAL=y
CONFIG_OF_LIBFDT=y
# CONFIG_CMD_MISC is not set
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_MTD_NOR_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x1a000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_BAUDRATE=38400
CONFIG_OF_LIBFDT=y
# CONFIG_CMD_MISC is not set
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_MTD_NOR_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x1a000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_BAUDRATE=38400
CONFIG_OF_LIBFDT=y
# CONFIG_CMD_MISC is not set
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_MTD_NOR_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_SMC911X=y
+CONFIG_SMC911X_BASE=0x4e000000
+CONFIG_SMC911X_32_BIT=y
CONFIG_BAUDRATE=38400
CONFIG_OF_LIBFDT=y
This driver supports Realtek 8169 series gigabit ethernet family of
PCI/PCIe chipsets/adapters.
+config SMC911X
+ bool "SMSC LAN911x and LAN921x controller driver"
+
+if SMC911X
+
+config SMC911X_BASE
+ hex "SMC911X Base Address"
+ help
+ Define this to hold the physical address
+ of the device (I/O space)
+
+choice
+ prompt "SMC911X bus width"
+ default SMC911X_16_BIT
+
+config SMC911X_32_BIT
+ bool "Enable 32-bit interface"
+
+config SMC911X_16_BIT
+ bool "Enable 16-bit interface"
+ help
+ Define this if data bus is 16 bits. If your processor
+ automatically converts one 32 bit word to two 16 bit
+ words you may also try CONFIG_SMC911X_32_BIT.
+
+endchoice
+endif #SMC911X
+
config SUN7I_GMAC
bool "Enable Allwinner GMAC Ethernet support"
help
#define CONFIG_DISPLAY_BOARDINFO
#undef CONFIG_SHOW_BOOT_PROGRESS
-/* SMC9118 */
-#define CONFIG_SMC911X 1
-#define CONFIG_SMC911X_32_BIT 1
-#define CONFIG_SMC911X_BASE 0xB6080000
-
/* MEMORY */
#define AP325RXA_SDRAM_BASE (0x88000000)
#define AP325RXA_FLASH_BASE_1 (0xA0000000)
#undef CONFIG_CMD_SPI
#endif
-/* BLANCHE on board LANC: SMC89218 (ExCS0) */
#define CONFIG_NET_MULTI
-#define CONFIG_SMC911X 1
-#define CONFIG_SMC911X_16_BIT 1
-#define CONFIG_SMC911X_BASE 0x18000000
/* Board Clock */
#define RMOBILE_XTAL_CLK 20000000u
#define CONFIG_ENV_OFFSET 0x260000
#define CONFIG_ENV_ADDR 0x260000
-#if defined(CONFIG_CMD_NET)
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_32_BIT
-#define CM_T3X_SMC911X_BASE 0x2C000000
-#define SB_T35_SMC911X_BASE (CM_T3X_SMC911X_BASE + (16 << 20))
-#define CONFIG_SMC911X_BASE CM_T3X_SMC911X_BASE
-#endif /* (CONFIG_CMD_NET) */
-
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
#define CONFIG_DRIVER_TI_EMAC
#define CONFIG_DRIVER_TI_EMAC_USE_RMII
#define CONFIG_MII
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_32_BIT
-#define CONFIG_SMC911X_BASE (0x2C000000 + (16 << 20))
#define CONFIG_ARP_TIMEOUT 200UL
#define CONFIG_NET_RETRY_COUNT 5
#endif /* CONFIG_CMD_NET */
#define CONFIG_SYS_ENABLE_PADS_ALL
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_32_BIT
-#define CONFIG_SMC911X_BASE 0x2C000000
-
/* GPIO */
/* ENV related config options */
/* Ethernet Controllor Driver */
#ifdef CONFIG_CMD_NET
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_BASE 0x5000000
-#define CONFIG_SMC911X_16_BIT
#define CONFIG_ENV_SROM_BANK 1
#endif /*CONFIG_CMD_NET*/
"pclk:185925,le:9,ri:17,up:7,lo:10,hs:1,vs:1," \
"sync:1241513985,vmode:0\0"
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_BASE 0xa8000000
-#define CONFIG_SMC911X_32_BIT
-
/*
* Miscellaneous configurable options
*/
#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ
#define TMU_CLK_DIVIDER (4) /* 4 (default), 16, 64, 256 or 1024 */
-/* Ether */
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_BASE (0x10000000)
-#define CONFIG_SMC911X_32_BIT
#define CONFIG_NFS_TIMEOUT 10000UL
/* I2C */
"nand erase 0x0 0x40000; " \
"nand write 0x81000000 0x0 0x40000\0"
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_BASE 0xB6000000
-#define CONFIG_SMC911X_32_BIT
-
/*
* Miscellaneous configurable options
*/
/*
* Ethernet on the debug board (SMC911)
*/
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_16_BIT 1
-#define CONFIG_SMC911X_BASE CS5_BASE_ADDR
-
#define CONFIG_HAS_ETH1
#define CONFIG_ETHPRIME
#define CONFIG_ETHPRIME "smc911x"
-/*Support LAN9217*/
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_16_BIT
-#define CONFIG_SMC911X_BASE CS1_BASE_ADDR
-
#define CONFIG_LOADADDR 0x72000000 /* loadaddr env var */
#define CONFIG_SYS_TEXT_BASE 0x77800000
/* USB EHCI */
#define CONFIG_SYS_USB_FAT_BOOT_PARTITION 1
-/* SMSC911x Ethernet */
-#if defined(CONFIG_CMD_NET)
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_32_BIT
-#define CONFIG_SMC911X_BASE 0x2C000000
-#endif /* CONFIG_CMD_NET */
-
/* Environment */
#define CONFIG_PREBOOT "usb start"
#endif
-/*
- * SMSC911x Ethernet
- */
-#if defined(CONFIG_CMD_NET)
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_32_BIT
-#define CONFIG_SMC911X_BASE 0x2C000000
-#endif /* (CONFIG_CMD_NET) */
-
#define CONFIG_MTD_PARTITIONS
#define CONFIG_SYS_MTDPARTS_RUNTIME
#define CONFIG_ENV_OFFSET 0x260000
#define CONFIG_ENV_ADDR 0x260000
-/* SMSC922x Ethernet */
-#if defined(CONFIG_CMD_NET)
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_32_BIT
-#define CONFIG_SMC911X_BASE 0x08000000
-#endif /* (CONFIG_CMD_NET) */
-
/* Defines for SPL */
/* NAND: SPL falcon mode configs */
#define CONFIG_ENV_OFFSET 0x240000
#define CONFIG_ENV_ADDR 0x240000
-/* Configure SMSC9211 ethernet */
-#if defined(CONFIG_CMD_NET)
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_32_BIT
-#define CONFIG_SMC911X_BASE 0x2C000000
-#endif /* (CONFIG_CMD_NET) */
-
/* Initial RAM setup */
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
#define CONFIG_ENV_OFFSET 0x260000
#define CONFIG_ENV_ADDR 0x260000
-#ifdef CONFIG_CMD_NET
-/* Ethernet (LAN9211 from SMSC9118 family) */
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_32_BIT
-#define CONFIG_SMC911X_BASE DEBUG_BASE
-
-#endif
-
#endif /* __CONFIG_H */
#define CONFIG_BITBANGMII_MULTI
#define CONFIG_SH_ETHER_SH7734_MII (0x00) /* MII */
#define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_MII
-#ifndef CONFIG_SH_ETHER
-# define CONFIG_SMC911X
-# define CONFIG_SMC911X_16_BIT
-# define CONFIG_SMC911X_BASE (0x84000000)
-#endif
/* undef to save memory */
#define CONFIG_SYS_LONGHELP
#define CMT_CLK_DIVIDER 32 /* 8 (default), 32, 128 or 512 */
#define CONFIG_SH_CMT_CLK_FREQ (CONFIG_SYS_CLK_FREQ / CMT_CLK_DIVIDER)
-/* Network interface */
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_16_BIT
-#define CONFIG_SMC911X_BASE (0x24000000)
-
#endif /* __RSK7203_H */
#define CMT_CLK_DIVIDER 32 /* 8 (default), 32, 128 or 512 */
#define CONFIG_SH_CMT_CLK_FREQ (CONFIG_SYS_CLK_FREQ / CMT_CLK_DIVIDER)
-/* Network interface */
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_16_BIT
-#define CONFIG_SMC911X_BASE 0x28000000
-
#endif /* __RSK7264_H */
#define CMT_CLK_DIVIDER 32 /* 8 (default), 32, 128 or 512 */
#define CONFIG_SH_CMT_CLK_FREQ (CONFIG_SYS_CLK_FREQ / CMT_CLK_DIVIDER)
-/* Network interface */
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_16_BIT
-#define CONFIG_SMC911X_BASE 0x24000000
-
#endif /* __RSK7269_H */
* Ethernet Contoller driver
*/
#ifdef CONFIG_CMD_NET
-#define CONFIG_SMC911X 1 /* we have a SMC9115 on-board */
-#define CONFIG_SMC911X_16_BIT 1 /* SMC911X_16_BIT Mode */
-#define CONFIG_SMC911X_BASE 0x98800300 /* SMC911X Drive Base */
#define CONFIG_ENV_SROM_BANK 3 /* Select SROM Bank-3 for Ethernet*/
#endif /* CONFIG_CMD_NET */
/* Ethernet Controllor Driver */
#ifdef CONFIG_CMD_NET
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_BASE 0x5000000
-#define CONFIG_SMC911X_16_BIT
#define CONFIG_ENV_SROM_BANK 1
#endif /*CONFIG_CMD_NET*/
#define CONFIG_HOSTNAME twister
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_16_BIT
-#define CONFIG_SMC911X_BASE 0x2C000000
-#define CONFIG_SMC911X_NO_EEPROM
-
#define CONFIG_EXTRA_ENV_SETTINGS CONFIG_TAM3517_SETTINGS \
"bootcmd=run nandboot\0"
/* FLASH related */
#define CONFIG_MTD_DEVICE
-#define CONFIG_SMC911X_32_BIT
-/* dummy: referenced by examples/standalone/smc911x_eeprom.c */
-#define CONFIG_SMC911X_BASE 0
-
-#ifdef CONFIG_MICRO_SUPPORT_CARD
-#define CONFIG_SMC911X
-#endif
-
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_LOAD_ADDR 0x80400000 /* default load address */
#if defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)
-/*
- * SMSC91C11x Network Card
- */
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_BASE 0x00000000
-#define CONFIG_SMC911X_32_BIT
#define CONFIG_NET_RETRY_COUNT 20
#endif
/*
* Commands
*/
-
-/*
- * Only Premium/Platinum have ethernet support right now
- */
-#if (defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)) && \
- !defined(CONFIG_VCT_SMALL_IMAGE)
-#endif
-
-/*
- * Only Premium/Platinum have USB-EHCI support right now
- */
-#if (defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)) && \
- !defined(CONFIG_VCT_SMALL_IMAGE)
-#endif
-
#if defined(CONFIG_CMD_USB)
#define CONFIG_SUPPORT_VFAT
* (NOR/OneNAND) usage and Linux kernel booting.
*/
#if defined(CONFIG_VCT_SMALL_IMAGE)
-#undef CONFIG_SMC911X
#undef CONFIG_SYS_I2C_SOFT
#undef CONFIG_SOURCE
#undef CONFIG_SYS_LONGHELP
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (8 << 20))
-/* Ethernet Configuration */
-#ifdef CONFIG_TARGET_VEXPRESS64_JUNO
-/* The real hardware Versatile express uses SMSC9118 */
-#define CONFIG_SMC911X 1
-#define CONFIG_SMC911X_32_BIT 1
-#define CONFIG_SMC911X_BASE (0x018000000)
-#else
+#ifndef CONFIG_TARGET_VEXPRESS64_JUNO
/* The Vexpress64 simulators use SMSC91C111 */
#define CONFIG_SMC91111 1
#define CONFIG_SMC91111_BASE (0x01A000000)
#define V2M_NOR1 (V2M_PA_CS1)
#define V2M_SRAM (V2M_PA_CS2)
#define V2M_VIDEO_SRAM (V2M_PA_CS3 + 0x00000000)
-#define V2M_LAN9118 (V2M_PA_CS3 + 0x02000000)
#define V2M_ISP1761 (V2M_PA_CS3 + 0x03000000)
/* Common peripherals relative to CS7. */
#define CONFIG_SYS_TIMER_COUNTER (V2M_TIMER01 + 0x4)
#define CONFIG_SYS_TIMER_COUNTS_DOWN
-/* SMSC9115 Ethernet from SMSC9118 family */
-#define CONFIG_SMC911X 1
-#define CONFIG_SMC911X_32_BIT 1
-#define CONFIG_SMC911X_BASE V2M_LAN9118
-
/* PL011 Serial Configuration */
#define CONFIG_PL011_SERIAL
#define CONFIG_PL011_CLOCK 24000000
CONFIG_SMC91111
CONFIG_SMC91111_BASE
CONFIG_SMC91111_EXT_PHY
-CONFIG_SMC911X
-CONFIG_SMC911X_16_BIT
-CONFIG_SMC911X_32_BIT
-CONFIG_SMC911X_BASE
-CONFIG_SMC911X_NO_EEPROM
CONFIG_SMC_AUTONEG_TIMEOUT
CONFIG_SMC_USE_32_BIT
CONFIG_SMC_USE_IOFUNCS