drivers/net/e1000: Introduce CONFIG_E1000_NO_NVM
authorRojhalat Ibrahim <imr@rtschenk.de>
Mon, 7 Oct 2013 16:30:39 +0000 (18:30 +0200)
committerJoe Hershberger <joe.hershberger@ni.com>
Fri, 22 Nov 2013 23:03:19 +0000 (17:03 -0600)
The e1000 driver expects to always have some kind of non-volatile memory
attached directly to the ethernet controller chip. This means that I would
have to add an additional separate flash chip to my custom board just to
store essentially the MAC address. Since I don't want to do that, this patch
introduces a new config option CONFIG_E1000_NO_NVM. If defined it disables
all accesses to the NVM. I have tested the patch with a 82574 controller.

Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
drivers/net/e1000.c
drivers/net/e1000.h

index 57aa53dbae77b06230c160dd7e56f37a4cd21d39..9a66e68ae0debb57373d611d8314646123a11e99 100644 (file)
@@ -114,12 +114,13 @@ static int e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr,
 static int32_t e1000_phy_hw_reset(struct e1000_hw *hw);
 static int e1000_phy_reset(struct e1000_hw *hw);
 static int e1000_detect_gig_phy(struct e1000_hw *hw);
-static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw);
 static void e1000_set_media_type(struct e1000_hw *hw);
 
 static int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask);
 static int32_t e1000_check_phy_reset_block(struct e1000_hw *hw);
 
+#ifndef CONFIG_E1000_NO_NVM
+static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw);
 static int32_t e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset,
                uint16_t words,
                uint16_t *data);
@@ -885,6 +886,7 @@ static int e1000_validate_eeprom_checksum(struct e1000_hw *hw)
 
        return -E1000_ERR_EEPROM;
 }
+#endif /* CONFIG_E1000_NO_NVM */
 
 /*****************************************************************************
  * Set PHY to class A mode
@@ -897,6 +899,7 @@ static int e1000_validate_eeprom_checksum(struct e1000_hw *hw)
 static int32_t
 e1000_set_phy_mode(struct e1000_hw *hw)
 {
+#ifndef CONFIG_E1000_NO_NVM
        int32_t ret_val;
        uint16_t eeprom_data;
 
@@ -923,10 +926,11 @@ e1000_set_phy_mode(struct e1000_hw *hw)
                        hw->phy_reset_disable = false;
                }
        }
-
+#endif
        return E1000_SUCCESS;
 }
 
+#ifndef CONFIG_E1000_NO_NVM
 /***************************************************************************
  *
  * Obtaining software semaphore bit (SMBI) before resetting PHY.
@@ -965,6 +969,7 @@ e1000_get_software_semaphore(struct e1000_hw *hw)
 
        return E1000_SUCCESS;
 }
+#endif
 
 /***************************************************************************
  * This function clears HW semaphore bits.
@@ -977,6 +982,7 @@ e1000_get_software_semaphore(struct e1000_hw *hw)
 static void
 e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw)
 {
+#ifndef CONFIG_E1000_NO_NVM
         uint32_t swsm;
 
        DEBUGFUNC();
@@ -991,6 +997,7 @@ e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw)
        } else
                swsm &= ~(E1000_SWSM_SWESMBI);
        E1000_WRITE_REG(hw, SWSM, swsm);
+#endif
 }
 
 /***************************************************************************
@@ -1007,6 +1014,7 @@ e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw)
 static int32_t
 e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw)
 {
+#ifndef CONFIG_E1000_NO_NVM
        int32_t timeout;
        uint32_t swsm;
 
@@ -1043,7 +1051,7 @@ e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw)
                                "SWESMBI bit is set.\n");
                return -E1000_ERR_EEPROM;
        }
-
+#endif
        return E1000_SUCCESS;
 }
 
@@ -1097,6 +1105,7 @@ static bool e1000_is_second_port(struct e1000_hw *hw)
        }
 }
 
+#ifndef CONFIG_E1000_NO_NVM
 /******************************************************************************
  * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
  * second function of dual function devices
@@ -1136,6 +1145,7 @@ e1000_read_mac_addr(struct eth_device *nic)
 #endif
        return 0;
 }
+#endif
 
 /******************************************************************************
  * Initializes receive address filters.
@@ -1764,9 +1774,11 @@ static int
 e1000_setup_link(struct eth_device *nic)
 {
        struct e1000_hw *hw = nic->priv;
-       uint32_t ctrl_ext;
        int32_t ret_val;
+#ifndef CONFIG_E1000_NO_NVM
+       uint32_t ctrl_ext;
        uint16_t eeprom_data;
+#endif
 
        DEBUGFUNC();
 
@@ -1775,6 +1787,7 @@ e1000_setup_link(struct eth_device *nic)
        if (e1000_check_phy_reset_block(hw))
                return E1000_SUCCESS;
 
+#ifndef CONFIG_E1000_NO_NVM
        /* Read and store word 0x0F of the EEPROM. This word contains bits
         * that determine the hardware's default PAUSE (flow control) mode,
         * a bit that determines whether the HW defaults to enabling or
@@ -1788,7 +1801,7 @@ e1000_setup_link(struct eth_device *nic)
                DEBUGOUT("EEPROM Read Error\n");
                return -E1000_ERR_EEPROM;
        }
-
+#endif
        if (hw->fc == e1000_fc_default) {
                switch (hw->mac_type) {
                case e1000_ich8lan:
@@ -1797,6 +1810,7 @@ e1000_setup_link(struct eth_device *nic)
                        hw->fc = e1000_fc_full;
                        break;
                default:
+#ifndef CONFIG_E1000_NO_NVM
                        ret_val = e1000_read_eeprom(hw,
                                EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data);
                        if (ret_val) {
@@ -1809,6 +1823,7 @@ e1000_setup_link(struct eth_device *nic)
                                    EEPROM_WORD0F_ASM_DIR)
                                hw->fc = e1000_fc_tx_pause;
                        else
+#endif
                                hw->fc = e1000_fc_full;
                        break;
                }
@@ -1828,6 +1843,7 @@ e1000_setup_link(struct eth_device *nic)
 
        DEBUGOUT("After fix-ups FlowControl is now = %x\n", hw->fc);
 
+#ifndef CONFIG_E1000_NO_NVM
        /* Take the 4 bits from EEPROM word 0x0F that determine the initial
         * polarity value for the SW controlled pins, and setup the
         * Extended Device Control reg with that info.
@@ -1840,6 +1856,7 @@ e1000_setup_link(struct eth_device *nic)
                            SWDPIO__EXT_SHIFT);
                E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
        }
+#endif
 
        /* Call the necessary subroutine to configure the link. */
        ret_val = (hw->media_type == e1000_media_type_fiber) ?
@@ -5196,6 +5213,7 @@ e1000_initialize(bd_t * bis)
                e1000_reset_hw(hw);
                list_add_tail(&hw->list_node, &e1000_hw_list);
 
+#ifndef CONFIG_E1000_NO_NVM
                /* Validate the EEPROM and get chipset information */
 #if !defined(CONFIG_MVBC_1G)
                if (e1000_init_eeprom_params(hw)) {
@@ -5206,11 +5224,17 @@ e1000_initialize(bd_t * bis)
                        continue;
 #endif
                e1000_read_mac_addr(nic);
+#endif
                e1000_get_bus_type(hw);
 
+#ifndef CONFIG_E1000_NO_NVM
                printf("e1000: %02x:%02x:%02x:%02x:%02x:%02x\n       ",
                       nic->enetaddr[0], nic->enetaddr[1], nic->enetaddr[2],
                       nic->enetaddr[3], nic->enetaddr[4], nic->enetaddr[5]);
+#else
+               memset(nic->enetaddr, 0, 6);
+               printf("e1000: no NVM\n");
+#endif
 
                /* Set up the function pointers and register the device */
                nic->init = e1000_init;
index 25884f5bc5241cfcd6c65698afb75aa724bd0ba3..ff87af2ef8a4a877a496e3dc58fe005ccaff7580 100644 (file)
@@ -63,11 +63,14 @@ struct e1000_hw_stats;
 
 /* Internal E1000 helper functions */
 struct e1000_hw *e1000_find_card(unsigned int cardnum);
+
+#ifndef CONFIG_E1000_NO_NVM
 int32_t e1000_acquire_eeprom(struct e1000_hw *hw);
 void e1000_standby_eeprom(struct e1000_hw *hw);
 void e1000_release_eeprom(struct e1000_hw *hw);
 void e1000_raise_ee_clk(struct e1000_hw *hw, uint32_t *eecd);
 void e1000_lower_ee_clk(struct e1000_hw *hw, uint32_t *eecd);
+#endif
 
 #ifdef CONFIG_E1000_SPI
 int do_e1000_spi(cmd_tbl_t *cmdtp, struct e1000_hw *hw,
@@ -1019,6 +1022,7 @@ struct e1000_hw_stats {
        uint64_t tsctfc;
 };
 
+#ifndef CONFIG_E1000_NO_NVM
 struct e1000_eeprom_info {
 e1000_eeprom_type type;
        uint16_t word_size;
@@ -1029,6 +1033,7 @@ e1000_eeprom_type type;
        bool use_eerd;
        bool use_eewr;
 };
+#endif
 
 typedef enum {
     e1000_smart_speed_default = 0,
@@ -1081,10 +1086,14 @@ struct e1000_hw {
        uint32_t io_base;
 #endif
        uint32_t                asf_firmware_present;
+#ifndef CONFIG_E1000_NO_NVM
        uint32_t                eeprom_semaphore_present;
+#endif
        uint32_t                swfw_sync_present;
        uint32_t                swfwhw_semaphore_present;
+#ifndef CONFIG_E1000_NO_NVM
        struct e1000_eeprom_info eeprom;
+#endif
        e1000_ms_type           master_slave;
        e1000_ms_type           original_master_slave;
        e1000_ffe_config        ffe_config_state;