+++ /dev/null
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM spi # Boot from SPI flash
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1b1b1b9b
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000a00 # DDR Configuration register
-# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x38543000 # DDR Controller Control Low
-# bit 4: 0=addr/cmd in smame cycle
-# bit 5: 0=clk is driven during self refresh, we don't care for APX
-# bit 6: 0=use recommended falling edge of clk for addr/cmd
-# bit14: 0=input buffer always powered up
-# bit18: 1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31: 0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x2202433D # DDR Timing (Low) (active cycles value +1)
-# bit3-0: TRAS lsbs
-# bit7-4: TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20: TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x0000002A # DDR Timing (High)
-# bit6-0: TRFC
-# bit8-7: TR2R
-# bit10-9: TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x0000000D # DDR Address Control
-# bit1-0: 01, Cs0width=x16
-# bit3-2: 11, Cs0size=1Gb
-# bit5-4: 00, Cs2width=nonexistent
-# bit7-6: 00, Cs1size =nonexistent
-# bit9-8: 00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16: 0, Cs0AddrSel
-# bit17: 0, Cs1AddrSel
-# bit18: 0, Cs2AddrSel
-# bit19: 0, Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
-# bit0: 0, OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000 # DDR Operation
-# bit3-0: 0x0, DDR cmd
-# bit31-4: 0 required
-
-DATA 0xFFD0141C 0x00000C52 # DDR Mode
-# bit2-0: 2, BurstLen=2 required
-# bit3: 0, BurstType=0 required
-# bit6-4: 4, CL=5
-# bit7: 0, TestMode=0 normal
-# bit8: 0, DLL reset=0 normal
-# bit11-9: 6, auto-precharge write recovery ????????????
-# bit12: 0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000046 # DDR Extended Mode
-# bit0: 0, DDR DLL enabled
-# bit1: 1, DDR drive strenght reduced
-# bit2: 1, DDR ODT control lsd enabled
-# bit5-3: 000, required
-# bit6: 1, DDR ODT control msb, enabled
-# bit9-7: 000, required
-# bit10: 0, differential DQS enabled
-# bit11: 0, required
-# bit12: 0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F1FF # DDR Controller Control High
-# bit2-0: 111, required
-# bit3 : 1 , MBUS Burst Chop disabled
-# bit6-4: 111, required
-# bit7 : 1 , D2P Latency enabled
-# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9 : 0 , no half clock cycle addition to dataout
-# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0 required
-
-DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
-# bit0: 1, Window enabled
-# bit1: 0, Write Protect disabled
-# bit3-2: 00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x07, Size (i.e. 128MB)
-
-DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
-DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00010001 # DDR ODT Control (Low)
-# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
-# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
-
-DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
-# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
-# bit3-2: 01, ODT1 active NEVER!
-# bit31-4: zero, required
-
-DATA 0xFFD0149C 0x0000E811 # CPU ODT Control
-# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
-# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
-# bit11-10:1, DQ_ODTSel. ODT select turned on
-
-DATA 0xFFD01480 0x00000001 # DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
+++ /dev/null
-/*
- * Maintainer : Prafulla Wadaskar <prafulla@marvell.com>
- *
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include "mv88f6281gtw_ge.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
- /*
- * default gpio configuration
- * There are maximum 64 gpios controlled through 2 sets of registers
- * the below configuration configures mainly initial LED status
- */
- mvebu_config_gpio(MV88F6281GTW_GE_OE_VAL_LOW,
- MV88F6281GTW_GE_OE_VAL_HIGH,
- MV88F6281GTW_GE_OE_LOW, MV88F6281GTW_GE_OE_HIGH);
-
- /* Multi-Purpose Pins Functionality configuration */
- static const u32 kwmpp_config[] = {
- MPP0_SPI_SCn,
- MPP1_SPI_MOSI,
- MPP2_SPI_SCK,
- MPP3_SPI_MISO,
- MPP4_GPIO,
- MPP5_GPO,
- MPP6_SYSRST_OUTn,
- MPP7_SPI_SCn,
- MPP8_TW_SDA,
- MPP9_TW_SCK,
- MPP10_UART0_TXD,
- MPP11_UART0_RXD,
- MPP12_GPO,
- MPP13_GPIO,
- MPP14_GPIO,
- MPP15_GPIO,
- MPP16_GPIO,
- MPP17_GPIO,
- MPP18_GPO,
- MPP19_GPO,
- MPP20_GPIO,
- MPP21_GPIO,
- MPP22_GPIO,
- MPP23_GPIO,
- MPP24_GPIO,
- MPP25_GPIO,
- MPP26_GPIO,
- MPP27_GPIO,
- MPP28_GPIO,
- MPP29_GPIO,
- MPP30_GPIO,
- MPP31_GPIO,
- MPP32_GPIO,
- MPP33_GPIO,
- MPP34_GPIO,
- MPP35_GPIO,
- MPP36_GPIO,
- MPP37_GPIO,
- MPP38_GPIO,
- MPP39_GPIO,
- MPP40_GPIO,
- MPP41_GPIO,
- MPP42_GPIO,
- MPP43_GPIO,
- MPP44_GPIO,
- MPP45_GPIO,
- MPP46_GPIO,
- MPP47_GPIO,
- MPP48_GPIO,
- MPP49_GPIO,
- 0
- };
- kirkwood_mpp_conf(kwmpp_config, NULL);
- return 0;
-}
-
-int board_init(void)
-{
- /*
- * arch number of board
- */
- gd->bd->bi_arch_number = MACH_TYPE_MV88F6281GTW_GE;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
-
- return 0;
-}
-
-#ifdef CONFIG_MV88E61XX_SWITCH
-void reset_phy(void)
-{
- /* configure and initialize switch */
- struct mv88e61xx_config swcfg = {
- .name = "egiga0",
- .vlancfg = MV88E61XX_VLANCFG_ROUTER,
- .rgmii_delay = MV88E61XX_RGMII_DELAY_EN,
- .led_init = MV88E61XX_LED_INIT_EN,
- .mdip = MV88E61XX_MDIP_REVERSE,
- .portstate = MV88E61XX_PORTSTT_FORWARDING,
- .cpuport = (1 << 5),
- .ports_enabled = 0x3f
- };
-
- mv88e61xx_switch_initialize(&swcfg);
-}
-#endif /* CONFIG_MV88E61XX_SWITCH */
+++ /dev/null
-/*
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _CONFIG_MV88F6281GTW_GE_H
-#define _CONFIG_MV88F6281GTW_GE_H
-
-/*
- * Version number information
- */
-#define CONFIG_IDENT_STRING "\nMarvell-MV88F6281GTW_GE"
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
-#define CONFIG_KW88F6281 1 /* SOC Name */
-#define CONFIG_MACH_MV88F6281GTW_GE /* Machine type */
-#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-
-/*
- * Commands configuration
- */
-#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_USB
-
-/*
- * mv-common.h should be defined after CMD configs since it used them
- * to enable certain macros
- */
-#include "mv-common.h"
-
-/* Unwanted stuffs from mv-common.h */
-#undef CONFIG_CMD_EXT2
-#undef CONFIG_CMD_JFFS2
-#undef CONFIG_CMD_FAT
-#undef CONFIG_CMD_UBI
-#undef CONFIG_CMD_UBIFS
-#undef CONFIG_RBTREE
-
-/*
- * Environment variables configurations
- */
-#ifdef CONFIG_SPI_FLASH
-#define CONFIG_ENV_IS_IN_SPI_FLASH 1
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K */
-#else
-#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
-#endif
-#define CONFIG_ENV_SIZE 0x1000 /* 4k */
-#define CONFIG_ENV_ADDR 0x30000
-#define CONFIG_ENV_OFFSET 0x30000 /* env starts here */
-
-/*
- * Default environment variables
- */
-#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
- "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
- "${x_bootcmd_usb}; bootm 0x6400000;"
-
-#define CONFIG_MTDPARTS "spi0.0:512k(uboot)," \
- "512k@512k(psm),2m@1m(kernel),13m@3m(rootfs)\0"
-
-#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
- "=ttyS0,115200 mtdparts="CONFIG_MTDPARTS \
- "x_bootcmd_kernel=cp.b 0xE8100000 0x6400000 0x200000\0" \
- "x_bootcmd_usb=usb start\0" \
- "x_bootargs_root=root=/dev/mtdblock3 ro rootfstype=squashfs\0"
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
-#define CONFIG_MV88E61XX_SWITCH /* Enable mv88e61xx switch driver */
-#endif /* CONFIG_CMD_NET */
-
-#endif /* _CONFIG_MV88F6281GTW_GE_H */
projects / oweals / u-boot.git / commitdiff