Changes since U-Boot 1.0.0:
======================================================================
+* Make CPU clock on ICA-IP board controllable by a "cpuclk"
+ environment variable which can set to "100", "133", or "150". The
+ CPU clock will be configured accordingly upon next reboot. Other
+ values are ignored. In case of an invalid or undefined "cpuclk"
+ value, the compile-time default CPU clock speed will be used.
+
+* Enable Quad-UART on BMS2003 board (initialize the PCMCIA memory
+ window that is used to access the UART registers by the Linux driver)
+
+* Patch by Reinhard Meyer, 20 Dec 2003:
+ Fix clock calculation for the MPC5200 for higher clock frequencies
+ (above 2**32 / 10 = 429.5 MHz).
+
+* Fix CONFIG_PLL_PCI_TO_MEM_MULTIPLIER divider error in SP8240 configuration
+
* Fix IceCube CLKIN configuration (it's 33.000000MHz)
* Add new configuration for IceCube board with DDR memory
while (learning) {
Read the README file in the top level directory;
- Read http://www.denx.de/re/DPLG.html
+ Read http://www.denx.de/twiki/bin/view/DULG/Manual ;
Read the source, Luke;
}
#define CGU_MUXCR(value) 0x0014(value)
#define CGU_PLL1SR(value) 0x000C(value)
- .globl memsetup
-memsetup:
+ .set noreorder
- /* EBU Initialization for the Flash CS0 and CS2.
- */
- li t0, EBU_MODUL_BASE
- li t1, 0xA0000041
- sw t1, EBU_ADDSEL0(t0)
+/*
+ * void ebu_init(long)
+ *
+ * a0 has the clock value we are going to run at
+ */
+ .globl ebu_init
+ .ent ebu_init
+ebu_init:
+
+ li t1, EBU_MODUL_BASE
+ li t2, 0xA0000041
+ sw t2, EBU_ADDSEL0(t1)
+ li t2, 0xA0800041
+ sw t2, EBU_ADDSEL2(t1)
+ li t2, 0xBE0000F1
+ sw t2, EBU_ADDSEL1(t1)
+
+ li t3, 100000000
+ beq a0, t3, 1f
+ nop
+ li t3, 133000000
+ beq a0, t3, 2f
+ nop
+ li t3, 150000000
+ beq a0, t3, 2f
+ nop
+ b 3f
+ nop
-#if CPU_CLOCK_RATE==100000000 /* 100 MHz clock for the MIPS core */
- lw t1, EBU_BUSCON0(t0) /* value set up by magic flash word */
- sw t1, EBU_BUSCON2(t0)
-#else /* 150 MHz or 133 MHz */
- li t1, 0x8841417E
- sw t1, EBU_BUSCON0(t0)
- sw t1, EBU_BUSCON2(t0)
-#endif
+ /* 100 MHz */
+1:
+ li t2, 0x8841417D
+ sw t2, EBU_BUSCON0(t1)
+ sw t2, EBU_BUSCON2(t1)
+ li t2, 0x684142BD
+ b 3f
+ sw t2, EBU_BUSCON1(t1) /* delay slot */
+
+ /* 133 or 150 MHz */
+2:
+ li t2, 0x8841417E
+ sw t2, EBU_BUSCON0(t1)
+ sw t2, EBU_BUSCON2(t1)
+ li t2, 0x684143FD
+ sw t2, EBU_BUSCON1(t1)
+3:
+ j ra
+ nop
+
+ .end ebu_init
- li t1, 0xA0800041
- sw t1, EBU_ADDSEL2(t0)
- /* Need to initialize CS1 too, so as to to prevent overlapping with
- * Flash bank 1.
+/*
+ * void cgu_init(long)
+ *
+ * a0 has the clock value
+ */
+ .globl cgu_init
+ .ent cgu_init
+cgu_init:
+
+ li t1, CGU_MODUL_BASE
+
+ li t3, 100000000
+ beq a0, t3, 1f
+ nop
+ li t3, 133000000
+ beq a0, t3, 2f
+ nop
+ li t3, 150000000
+ beq a0, t3, 3f
+ nop
+ b 5f
+ nop
+
+ /* 100 MHz clock */
+1:
+ li t2, 0x80000014
+ sw t2, CGU_DIVCR(t1)
+ li t2, 0x80000000
+ sw t2, CGU_MUXCR(t1)
+ li t2, 0x800B0001
+ b 5f
+ sw t2, CGU_PLL1CR(t1) /* delay slot */
+
+ /* 133 MHz clock */
+2:
+ li t2, 0x80000054
+ sw t2, CGU_DIVCR(t1)
+ li t2, 0x80000000
+ sw t2, CGU_MUXCR(t1)
+ li t2, 0x800B0001
+ b 5f
+ sw t2, CGU_PLL1CR(t1) /* delay slot */
+
+ /* 150 MHz clock */
+3:
+ li t2, 0x80000017
+ sw t2, CGU_DIVCR(t1)
+ li t2, 0xC00B0001
+ sw t2, CGU_PLL1CR(t1)
+ li t3, 0x80000000
+4:
+ lw t2, CGU_PLL1SR(t1)
+ and t2, t2, t3
+ beq t2, zero, 4b
+ nop
+ li t2, 0x80000001
+ sw t2, CGU_MUXCR(t1)
+5:
+ j ra
+ nop
+
+ .end cgu_init
+
+
+ .globl memsetup
+ .ent memsetup
+memsetup:
+
+ /* EBU and CGU Initialization.
*/
- li t1, 0xBE0000F1
- sw t1, EBU_ADDSEL1(t0)
-
-#if CPU_CLOCK_RATE==100000000 /* 100 MHz clock for the MIPS core */
- li t1, 0x684142BD
-#else /* 150 MHz or 133 MHz */
- li t1, 0x684143FD
-#endif
- sw t1, EBU_BUSCON1(t0)
-
-#if CPU_CLOCK_RATE==150000000 /* 150 MHz clock for the MIPS core */
- li t0, CGU_MODUL_BASE
- li t1, 0x80000017
- sw t1, CGU_DIVCR(t0)
- li t1, 0xC00B0001
- sw t1, CGU_PLL1CR(t0)
- lui t2, 0x8000
-b1:
- lw t1, CGU_PLL1SR(t0)
- and t1, t1, t2
- beq t1, zero, b1
- li t1, 0x80000001
- sw t1, CGU_MUXCR(t0)
-#elif CPU_CLOCK_RATE==133000000 /* 133 MHz clock for the MIPS core */
- li t0, CGU_MODUL_BASE
- li t1, 0x80000054
- sw t1, CGU_DIVCR(t0)
- li t1, 0x80000000
- sw t1, CGU_MUXCR(t0)
- li t1, 0x800B0001
- sw t1, CGU_PLL1CR(t0)
-#endif
+ li a0, CPU_CLOCK_RATE
+ move t0, ra
+
+ /* We rely on the fact that neither ebu_init() nor cgu_init()
+ * modify t0 and a0.
+ */
+ bal ebu_init
+ nop
+ bal cgu_init
+ nop
+ move ra, t0
/* SDRAM Initialization.
*/
j ra
nop
+ .end memsetup
+
break;
}
#endif /* CONFIG_IDE_8xx_PCCARD */
+#ifdef CONFIG_BMS2003
+ case 3: { /* map I/O window for 4xUART data/ctrl */
+ win->br += 0x140000;
+ win->or = ( PCMCIA_BSIZE_256K
+ | PCMCIA_PPS_8
+ | PCMCIA_PRS_IO
+ | slotbit
+ | PCMCIA_PV
+ | CFG_PCMCIA_TIMING );
+ break;
+ }
+#endif /* CONFIG_BMS2003 */
default: /* set to not valid */
win->or = 0;
break;
break;
}
}
+
+int incaip_set_cpuclk(void)
+{
+ uchar tmp[64];
+ ulong cpuclk;
+
+ if (getenv_r("cpuclk", tmp, sizeof(tmp)) > 0)
+ {
+ cpuclk = simple_strtoul(tmp, NULL, 10) * 1000000;
+ ebu_init(cpuclk);
+ cgu_init(cpuclk);
+ }
+
+ return 0;
+}
/* Bus-to-Core Multipliers */
static int bus2core[] = {
- 0, 0, 0, 10, 20, 20, 25, 45,
- 30, 55, 40, 50, 0, 60, 35, 0,
- 30, 25, 65, 10, 70, 20, 75, 45,
- 0, 55, 40, 50, 80, 60, 35, 0
+ 3, 2, 2, 2, 4, 4, 5, 9,
+ 6, 11, 8, 10, 3, 12, 7, 0,
+ 6, 5, 13, 2, 14, 4, 15, 9,
+ 0, 11, 8, 10, 16, 12, 7, 0
};
/* ------------------------------------------------------------------------- */
} else {
gd->bus_clk = vco / 4;
}
- gd->cpu_clk = gd->bus_clk * bus2core[val & 0x1f] / 10;
+ gd->cpu_clk = gd->bus_clk * bus2core[val & 0x1f] / 2;
val = *(vu_long *)MPC5XXX_CDM_CFG;
if (val & (1 << 8)) {
ulong get_PCLK (void);
ulong get_UCLK (void);
#endif
+#if defined CONFIG_INCA_IP
+uint incaip_get_cpuclk (void);
+#endif
ulong get_bus_freq (ulong);
#if defined(CONFIG_MPC85xx)
*/
#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
-#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 2
+#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 1
#define CFG_ROMNAL 7 /*rom/flash next access time */
#define CFG_ROMFAL 11 /*rom/flash access time */
#define CPU_CLOCK_RATE 133000000 /* 133 MHz clock for the MIPS core */
#endif
-#if CPU_CLOCK_RATE == 100000000
-#define INFINEON_EBU_BOOTCFG 0x20C4 /* CMULT = 4 for 100 MHz */
-#else
-#define INFINEON_EBU_BOOTCFG 0x40C4 /* CMULT = 8 for 150 MHz */
-#endif
-
+#define INFINEON_EBU_BOOTCFG 0x40C4 /* CMULT = 8 */
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CFG_BOOTPARAMS_LEN 128*1024
-#define CFG_HZ (CPU_CLOCK_RATE/2)
+#define CFG_HZ (incaip_get_cpuclk() / 2)
#define CFG_SDRAM_BASE 0x80000000
extern int timer_init(void);
+extern int incaip_set_cpuclk(void);
+
extern ulong uboot_end_data;
extern ulong uboot_end;
init_fnc_t *init_sequence[] = {
timer_init,
env_init, /* initialize environment */
+#ifdef CONFIG_INCA_IP
+ incaip_set_cpuclk, /* set cpu clock according to environment variable */
+#endif
init_baudrate, /* initialze baudrate settings */
serial_init, /* serial communications setup */
console_init_f,
projects / oweals / u-boot.git / commitdiff