--- /dev/null
+* Allwinner EMAC ethernet controller
+
+Required properties:
+- compatible: should be "allwinner,sun4i-a10-emac" (Deprecated:
+ "allwinner,sun4i-emac")
+- reg: address and length of the register set for the device.
+- interrupts: interrupt for the device
+- phy: see ethernet.txt file in the same directory.
+- clocks: A phandle to the reference clock for this device
+
+Example:
+
+emac: ethernet@01c0b000 {
+ compatible = "allwinner,sun4i-a10-emac";
+ reg = <0x01c0b000 0x1000>;
+ interrupts = <55>;
+ clocks = <&ahb_gates 17>;
+ phy = <&phy0>;
+};
--- /dev/null
+* Allwinner A10 MDIO Ethernet Controller interface
+
+Required properties:
+- compatible: should be "allwinner,sun4i-a10-mdio"
+ (Deprecated: "allwinner,sun4i-mdio").
+- reg: address and length of the register set for the device.
+
+Optional properties:
+- phy-supply: phandle to a regulator if the PHY needs one
+
+Example at the SoC level:
+mdio@01c0b080 {
+ compatible = "allwinner,sun4i-a10-mdio";
+ reg = <0x01c0b080 0x14>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+};
+
+And at the board level:
+
+mdio@01c0b080 {
+ phy-supply = <®_emac_3v3>;
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
--- /dev/null
+* Allwinner GMAC ethernet controller
+
+This device is a platform glue layer for stmmac.
+Please see stmmac.txt for the other unchanged properties.
+
+Required properties:
+ - compatible: Should be "allwinner,sun7i-a20-gmac"
+ - clocks: Should contain the GMAC main clock, and tx clock
+ The tx clock type should be "allwinner,sun7i-a20-gmac-clk"
+ - clock-names: Should contain the clock names "stmmaceth",
+ and "allwinner_gmac_tx"
+
+Optional properties:
+- phy-supply: phandle to a regulator if the PHY needs one
+
+Examples:
+
+ gmac: ethernet@01c50000 {
+ compatible = "allwinner,sun7i-a20-gmac";
+ reg = <0x01c50000 0x10000>,
+ <0x01c20164 0x4>;
+ interrupts = <0 85 1>;
+ interrupt-names = "macirq";
+ clocks = <&ahb_gates 49>, <&gmac_tx>;
+ clock-names = "stmmaceth", "allwinner_gmac_tx";
+ phy-mode = "mii";
+ };
--- /dev/null
+The following properties are common to the Ethernet controllers:
+
+- local-mac-address: array of 6 bytes, specifies the MAC address that was
+ assigned to the network device;
+- mac-address: array of 6 bytes, specifies the MAC address that was last used by
+ the boot program; should be used in cases where the MAC address assigned to
+ the device by the boot program is different from the "local-mac-address"
+ property;
+- max-speed: number, specifies maximum speed in Mbit/s supported by the device;
+- max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than
+ the maximum frame size (there's contradiction in ePAPR).
+- phy-mode: string, operation mode of the PHY interface; supported values are
+ "mii", "gmii", "sgmii", "qsgmii", "tbi", "rev-mii", "rmii", "rgmii", "rgmii-id",
+ "rgmii-rxid", "rgmii-txid", "rtbi", "smii", "xgmii"; this is now a de-facto
+ standard property;
+- phy-connection-type: the same as "phy-mode" property but described in ePAPR;
+- phy-handle: phandle, specifies a reference to a node representing a PHY
+ device; this property is described in ePAPR and so preferred;
+- phy: the same as "phy-handle" property, not recommended for new bindings.
+- phy-device: the same as "phy-handle" property, not recommended for new
+ bindings.
+
+Child nodes of the Ethernet controller are typically the individual PHY devices
+connected via the MDIO bus (sometimes the MDIO bus controller is separate).
+They are described in the phy.txt file in this same directory.
--- /dev/null
+* STMicroelectronics 10/100/1000 Ethernet driver (GMAC)
+
+Required properties:
+- compatible: Should be "snps,dwmac-<ip_version>" "snps,dwmac"
+ For backwards compatibility: "st,spear600-gmac" is also supported.
+- reg: Address and length of the register set for the device
+- interrupt-parent: Should be the phandle for the interrupt controller
+ that services interrupts for this device
+- interrupts: Should contain the STMMAC interrupts
+- interrupt-names: Should contain the interrupt names "macirq"
+ "eth_wake_irq" if this interrupt is supported in the "interrupts"
+ property
+- phy-mode: See ethernet.txt file in the same directory.
+- snps,reset-gpio gpio number for phy reset.
+- snps,reset-active-low boolean flag to indicate if phy reset is active low.
+- snps,reset-delays-us is triplet of delays
+ The 1st cell is reset pre-delay in micro seconds.
+ The 2nd cell is reset pulse in micro seconds.
+ The 3rd cell is reset post-delay in micro seconds.
+- snps,pbl Programmable Burst Length
+- snps,fixed-burst Program the DMA to use the fixed burst mode
+- snps,mixed-burst Program the DMA to use the mixed burst mode
+- snps,force_thresh_dma_mode Force DMA to use the threshold mode for
+ both tx and rx
+- snps,force_sf_dma_mode Force DMA to use the Store and Forward
+ mode for both tx and rx. This flag is
+ ignored if force_thresh_dma_mode is set.
+- snps,multicast-filter-bins: Number of multicast filter hash bins
+ supported by this device instance
+- snps,perfect-filter-entries: Number of perfect filter entries supported
+ by this device instance
+
+Optional properties:
+- resets: Should contain a phandle to the STMMAC reset signal, if any
+- reset-names: Should contain the reset signal name "stmmaceth", if a
+ reset phandle is given
+- max-frame-size: See ethernet.txt file in the same directory
+- clocks: If present, the first clock should be the GMAC main clock,
+ further clocks may be specified in derived bindings.
+- clock-names: One name for each entry in the clocks property, the
+ first one should be "stmmaceth".
+- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is
+ available this clock is used for programming the Timestamp Addend Register.
+ If not passed then the system clock will be used and this is fine on some
+ platforms.
+- snps,burst_len: The AXI burst lenth value of the AXI BUS MODE register.
+
+Examples:
+
+ gmac0: ethernet@e0800000 {
+ compatible = "st,spear600-gmac";
+ reg = <0xe0800000 0x8000>;
+ interrupt-parent = <&vic1>;
+ interrupts = <24 23>;
+ interrupt-names = "macirq", "eth_wake_irq";
+ mac-address = [000000000000]; /* Filled in by U-Boot */
+ max-frame-size = <3800>;
+ phy-mode = "gmii";
+ snps,multicast-filter-bins = <256>;
+ snps,perfect-filter-entries = <128>;
+ clocks = <&clock>;
+ clock-names = "stmmaceth";
+ };
projects / oweals / u-boot.git / commitdiff