These boards have not been converted to generic board by the deadline.
Remove them.
Signed-off-by: Simon Glass <sjg@chromium.org>
prompt "Marvell Kirkwood board select"
optional
-config TARGET_OPENRD
- bool "Marvell OpenRD Board"
-
config TARGET_RD6281A
bool "RD6281A Board"
config SYS_SOC
default "kirkwood"
-source "board/Marvell/openrd/Kconfig"
source "board/Marvell/rd6281a/Kconfig"
source "board/Marvell/dreamplug/Kconfig"
source "board/Marvell/guruplug/Kconfig"
+++ /dev/null
-if TARGET_OPENRD
-
-config SYS_BOARD
- default "openrd"
-
-config SYS_VENDOR
- default "Marvell"
-
-config SYS_CONFIG_NAME
- default "openrd"
-
-endif
+++ /dev/null
-OPENRD BOARD
-M: Prafulla Wadaskar <prafulla@marvell.com>
-S: Maintained
-F: board/Marvell/openrd/
-F: include/configs/openrd.h
-F: configs/openrd_base_defconfig
-
-OPENRD_CLIENT BOARD
-#M: -
-S: Maintained
-F: configs/openrd_client_defconfig
-F: configs/openrd_ultimate_defconfig
+++ /dev/null
-#
-# (C) Copyright 2009
-# Net Insight <www.netinsight.net>
-# Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
-#
-# Based on sheevaplug:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := openrd.o
+++ /dev/null
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM nand
-NAND_ECC_MODE default
-NAND_PAGE_SIZE 0x0800
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1b1b1b9b
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000c30 # DDR Configuration register
-# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
-# bit 4: 0=addr/cmd in smame cycle
-# bit 5: 0=clk is driven during self refresh, we don't care for APX
-# bit 6: 0=use recommended falling edge of clk for addr/cmd
-# bit14: 0=input buffer always powered up
-# bit18: 1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31: 0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
-# bit3-0: TRAS lsbs
-# bit7-4: TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20: TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
-# bit6-0: TRFC
-# bit8-7: TR2R
-# bit10-9: TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x000000cc # DDR Address Control
-# bit1-0: 00, Cs0width=x8
-# bit3-2: 11, Cs0size=1Gb
-# bit5-4: 00, Cs1width=x8
-# bit7-6: 11, Cs1size=1Gb
-# bit9-8: 00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16: 0, Cs0AddrSel
-# bit17: 0, Cs1AddrSel
-# bit18: 0, Cs2AddrSel
-# bit19: 0, Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
-# bit0: 0, OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000 # DDR Operation
-# bit3-0: 0x0, DDR cmd
-# bit31-4: 0 required
-
-DATA 0xFFD0141C 0x00000C52 # DDR Mode
-# bit2-0: 2, BurstLen=2 required
-# bit3: 0, BurstType=0 required
-# bit6-4: 4, CL=5
-# bit7: 0, TestMode=0 normal
-# bit8: 0, DLL reset=0 normal
-# bit11-9: 6, auto-precharge write recovery ????????????
-# bit12: 0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000042 # DDR Extended Mode
-# bit0: 0, DDR DLL enabled
-# bit1: 1, DDR drive strength reduced
-# bit2: 0, DDR ODT control lsd (disabled)
-# bit5-3: 000, required
-# bit6: 1, DDR ODT control msb, (disabled)
-# bit9-7: 000, required
-# bit10: 0, differential DQS enabled
-# bit11: 0, required
-# bit12: 0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
-# bit2-0: 111, required
-# bit3 : 1 , MBUS Burst Chop disabled
-# bit6-4: 111, required
-# bit7 : 0
-# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9 : 0 , no half clock cycle addition to dataout
-# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0 required
-
-DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
-# bit0: 1, Window enabled
-# bit1: 0, Write Protect disabled
-# bit3-2: 00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x0F, Size (i.e. 256MB)
-
-DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
-DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
-
-DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
-# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
-# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
-# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
-# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
-DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
-
-DATA 0xFFD0149C 0x0000E40f # CPU ODT Control
-# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
-# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
-# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
-# bit14: 1, M_STARTBURST_IN ODT: Enabled
-# bit15: 1, DDR IO ODT Unit: Use ODT block
-DATA 0xFFD01480 0x00000001 # DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
+++ /dev/null
-/*
- * (C) Copyright 2009
- * Net Insight <www.netinsight.net>
- * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
- *
- * Based on sheevaplug.c:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <miiphy.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include "openrd.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
- /*
- * default gpio configuration
- * There are maximum 64 gpios controlled through 2 sets of registers
- * the below configuration configures mainly initial LED status
- */
- mvebu_config_gpio(OPENRD_OE_VAL_LOW,
- OPENRD_OE_VAL_HIGH,
- OPENRD_OE_LOW, OPENRD_OE_HIGH);
-
- /* Multi-Purpose Pins Functionality configuration */
- static const u32 kwmpp_config[] = {
- MPP0_NF_IO2,
- MPP1_NF_IO3,
- MPP2_NF_IO4,
- MPP3_NF_IO5,
- MPP4_NF_IO6,
- MPP5_NF_IO7,
- MPP6_SYSRST_OUTn,
- MPP7_GPO,
- MPP8_TW_SDA,
- MPP9_TW_SCK,
- MPP10_UART0_TXD,
- MPP11_UART0_RXD,
- MPP12_SD_CLK,
- MPP13_SD_CMD, /* Alt UART1_TXD */
- MPP14_SD_D0, /* Alt UART1_RXD */
- MPP15_SD_D1,
- MPP16_SD_D2,
- MPP17_SD_D3,
- MPP18_NF_IO0,
- MPP19_NF_IO1,
- MPP20_GE1_0,
- MPP21_GE1_1,
- MPP22_GE1_2,
- MPP23_GE1_3,
- MPP24_GE1_4,
- MPP25_GE1_5,
- MPP26_GE1_6,
- MPP27_GE1_7,
- MPP28_GPIO,
- MPP29_TSMP9,
- MPP30_GE1_10,
- MPP31_GE1_11,
- MPP32_GE1_12,
- MPP33_GE1_13,
- MPP34_GPIO, /* UART1 / SD sel */
- MPP35_TDM_CH0_TX_QL,
- MPP36_TDM_SPI_CS1,
- MPP37_TDM_CH2_TX_QL,
- MPP38_TDM_CH2_RX_QL,
- MPP39_AUDIO_I2SBCLK,
- MPP40_AUDIO_I2SDO,
- MPP41_AUDIO_I2SLRC,
- MPP42_AUDIO_I2SMCLK,
- MPP43_AUDIO_I2SDI,
- MPP44_AUDIO_EXTCLK,
- MPP45_TDM_PCLK,
- MPP46_TDM_FS,
- MPP47_TDM_DRX,
- MPP48_TDM_DTX,
- MPP49_TDM_CH0_RX_QL,
- 0
- };
-
- kirkwood_mpp_conf(kwmpp_config, NULL);
- return 0;
-}
-
-int board_init(void)
-{
- /*
- * arch number of board
- */
-#if defined(CONFIG_BOARD_IS_OPENRD_BASE)
- gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
-#elif defined(CONFIG_BOARD_IS_OPENRD_CLIENT)
- gd->bd->bi_arch_number = MACH_TYPE_OPENRD_CLIENT;
-#elif defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE)
- gd->bd->bi_arch_number = MACH_TYPE_OPENRD_ULTIMATE;
-#endif
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
- return 0;
-}
-
-#ifdef CONFIG_RESET_PHY_R
-/* Configure and enable MV88E1116/88E1121 PHY */
-void mv_phy_init(char *name)
-{
- u16 reg;
- u16 devadr;
-
- if (miiphy_set_current_dev(name))
- return;
-
- /* command to read PHY dev address */
- if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
- printf("Err..%s could not read PHY dev address\n",
- __FUNCTION__);
- return;
- }
-
- /*
- * Enable RGMII delay on Tx and Rx for CPU port
- * Ref: sec 4.7.2 of chip datasheet
- */
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
- miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
- reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
- miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
- /* reset the phy */
- miiphy_reset(name, devadr);
-
- printf(PHY_NO" Initialized on %s\n", name);
-}
-
-void reset_phy(void)
-{
- mv_phy_init("egiga0");
-
-#ifdef CONFIG_BOARD_IS_OPENRD_CLIENT
- /* Kirkwood ethernet driver is written with the assumption that in case
- * of multiple PHYs, their addresses are consecutive. But unfortunately
- * in case of OpenRD-Client, PHY addresses are not consecutive.*/
- miiphy_write("egiga1", 0xEE, 0xEE, 24);
-#endif
-
-#if defined(CONFIG_BOARD_IS_OPENRD_CLIENT) || \
- defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE)
- /* configure and initialize both PHY's */
- mv_phy_init("egiga1");
-#endif
-}
-#endif /* CONFIG_RESET_PHY_R */
+++ /dev/null
-/*
- * (C) Copyright 2009
- * Net Insight <www.netinsight.net>
- * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
- *
- * Based on sheevaplug.h:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __OPENRD_BASE_H
-#define __OPENRD_BASE_H
-
-#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */
-#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */
-#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */
-#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */
-
-/* PHY related */
-#define MV88E1116_LED_FCTRL_REG 10
-#define MV88E1116_CPRSP_CR3_REG 21
-#define MV88E1116_MAC_CTRL_REG 21
-#define MV88E1116_PGADR_REG 22
-#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
-
-#endif /* __OPENRD_BASE_H */
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_KIRKWOOD=y
-CONFIG_TARGET_OPENRD=y
-CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_BASE"
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_SETEXPR is not set
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_KIRKWOOD=y
-CONFIG_TARGET_OPENRD=y
-CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_CLIENT"
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_SETEXPR is not set
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_KIRKWOOD=y
-CONFIG_TARGET_OPENRD=y
-CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_ULTIMATE"
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_SETEXPR is not set
+++ /dev/null
-/*
- * (C) Copyright 2009
- * Net Insight <www.netinsight.net>
- * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
- *
- * Based on sheevaplug.h:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _CONFIG_OPENRD_H
-#define _CONFIG_OPENRD_H
-
-/*
- * Version number information
- */
-#ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE
-# define CONFIG_IDENT_STRING "\nOpenRD-Ultimate"
-#else
-# ifdef CONFIG_BOARD_IS_OPENRD_CLIENT
-# define CONFIG_IDENT_STRING "\nOpenRD-Client"
-# else
-# ifdef CONFIG_BOARD_IS_OPENRD_BASE
-# define CONFIG_IDENT_STRING "\nOpenRD-Base"
-# else
-# error Unknown OpenRD board specified
-# endif
-# endif
-#endif
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */
-#define CONFIG_KW88F6281 1 /* SOC Name */
-#define CONFIG_MACH_OPENRD_BASE /* Machine type */
-#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-
-/*
- * Commands configuration
- */
-#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
-#define CONFIG_SYS_MVFS
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_IDE
-
-/*
- * mv-common.h should be defined after CMD configs since it used them
- * to enable certain macros
- */
-#include "mv-common.h"
-
-/*
- * Environment variables configurations
- */
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_ENV_IS_IN_NAND 1
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
-#else
-#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
-#endif
-/*
- * max 4k env size is enough, but in case of nand
- * it has to be rounded to sector size
- */
-#define CONFIG_ENV_SIZE 0x20000 /* 128k */
-#define CONFIG_ENV_ADDR 0x60000
-#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */
-/*
- * Environment is right behind U-Boot in flash. Make sure U-Boot
- * doesn't grow into the environment area.
- */
-#define CONFIG_BOARD_SIZE_LIMIT CONFIG_ENV_OFFSET
-
-/*
- * Default environment variables
- */
-#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
- "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
- "${x_bootcmd_usb}; bootm 0x6400000;"
-
-#define MTDIDS_DEFAULT "nand0=nand_mtd"
-#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000@0x000000(uboot),"\
- "0x400000@0x100000(uImage),"\
- "0x1fb00000@0x500000(rootfs)"
-
-#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
- "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
- "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
- "x_bootcmd_usb=usb start\0" \
- "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \
- "mtdids="MTDIDS_DEFAULT"\0" \
- "mtdparts="MTDPARTS_DEFAULT"\0"
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-# ifdef CONFIG_BOARD_IS_OPENRD_BASE
-# define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
-# else
-# define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */
-# endif
-# ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE
-# define CONFIG_PHY_BASE_ADR 0x0
-# define PHY_NO "88E1121"
-# else
-# define CONFIG_PHY_BASE_ADR 0x8
-# define PHY_NO "88E1116"
-# endif
-#endif /* CONFIG_CMD_NET */
-
-/*
- * SATA Driver configuration
- */
-#ifdef CONFIG_MVSATA_IDE
-#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
-#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
-#endif /*CONFIG_MVSATA_IDE*/
-
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_MVEBU_MMC
-#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE
-#endif /* CONFIG_CMD_MMC */
-
-#endif /* _CONFIG_OPENRD_BASE_H */
projects / oweals / u-boot.git / commitdiff