These boards have not been converted to generic board by the deadline.
Remove them.
Signed-off-by: Simon Glass <sjg@chromium.org>
bool "Ronetix pm9263 board"
select CPU_ARM926EJS
-config TARGET_STAMP9G20
- bool "Support stamp9g20"
- select CPU_ARM926EJS
-
config TARGET_AT91SAM9M10G45EK
bool "Atmel AT91SAM9M10G45-EK board"
select CPU_ARM926EJS
source "board/siemens/corvus/Kconfig"
source "board/siemens/taurus/Kconfig"
source "board/siemens/smartweb/Kconfig"
-source "board/taskit/stamp9g20/Kconfig"
endif
+++ /dev/null
-if TARGET_STAMP9G20
-
-config SYS_BOARD
- default "stamp9g20"
-
-config SYS_VENDOR
- default "taskit"
-
-config SYS_CONFIG_NAME
- default "stamp9g20"
-
-endif
+++ /dev/null
-STAMP9G20 BOARD
-M: Markus Hubig <mhubig@imko.de>
-S: Maintained
-F: board/taskit/stamp9g20/
-F: include/configs/stamp9g20.h
-F: configs/portuxg20_defconfig
-F: configs/stamp9g20_defconfig
+++ /dev/null
-#
-# (C) Copyright 2003-2008
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# (C) Copyright 2008
-# Stelian Pop <stelian@popies.net>
-# Lead Tech Design <www.leadtechdesign.com>
-#
-# (C) Copyright 2012
-# Markus Hubig <mhubig@imko.de>
-# IMKO GmbH <www.imko.de>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += stamp9g20.o
-obj-y += led.o
+++ /dev/null
-/*
- * Copyright (c) 2009 Wind River Systems, Inc.
- * Tom Rix <Tom.Rix@windriver.com>
- * (C) Copyright 2009
- * Eric Benard <eric@eukrea.com>
- *
- * (C) Copyright 2012
- * Markus Hubig <mhubig@imko.de>
- * IMKO GmbH <www.imko.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91_pmc.h>
-#include <status_led.h>
-
-static unsigned int saved_state[3] = {STATUS_LED_OFF,
- STATUS_LED_OFF, STATUS_LED_OFF};
-
-void coloured_LED_init(void)
-{
- struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
-
- /* Enable the clock */
- writel(ATMEL_ID_PIOC, &pmc->pcer);
-
- at91_set_gpio_output(CONFIG_RED_LED, 1);
- at91_set_gpio_output(CONFIG_GREEN_LED, 1);
- at91_set_gpio_output(CONFIG_YELLOW_LED, 1);
-
- at91_set_gpio_value(CONFIG_RED_LED, 0);
- at91_set_gpio_value(CONFIG_GREEN_LED, 1);
- at91_set_gpio_value(CONFIG_YELLOW_LED, 0);
-}
-
-void red_led_on(void)
-{
- at91_set_gpio_value(CONFIG_RED_LED, 1);
- saved_state[STATUS_LED_RED] = STATUS_LED_ON;
-}
-
-void red_led_off(void)
-{
- at91_set_gpio_value(CONFIG_RED_LED, 0);
- saved_state[STATUS_LED_RED] = STATUS_LED_OFF;
-}
-
-void green_led_on(void)
-{
- at91_set_gpio_value(CONFIG_GREEN_LED, 1);
- saved_state[STATUS_LED_GREEN] = STATUS_LED_ON;
-}
-
-void green_led_off(void)
-{
- at91_set_gpio_value(CONFIG_GREEN_LED, 0);
- saved_state[STATUS_LED_GREEN] = STATUS_LED_OFF;
-}
-
-void yellow_led_on(void)
-{
- at91_set_gpio_value(CONFIG_YELLOW_LED, 1);
- saved_state[STATUS_LED_YELLOW] = STATUS_LED_ON;
-}
-
-void yellow_led_off(void)
-{
- at91_set_gpio_value(CONFIG_YELLOW_LED, 0);
- saved_state[STATUS_LED_YELLOW] = STATUS_LED_OFF;
-}
-
-void __led_init(led_id_t mask, int state)
-{
- __led_set(mask, state);
-}
-
-void __led_toggle(led_id_t mask)
-{
- if (STATUS_LED_RED == mask) {
- if (STATUS_LED_ON == saved_state[STATUS_LED_RED])
- red_led_off();
- else
- red_led_on();
-
- } else if (STATUS_LED_GREEN == mask) {
- if (STATUS_LED_ON == saved_state[STATUS_LED_GREEN])
- green_led_off();
- else
- green_led_on();
-
- } else if (STATUS_LED_YELLOW == mask) {
- if (STATUS_LED_ON == saved_state[STATUS_LED_YELLOW])
- yellow_led_off();
- else
- yellow_led_on();
- }
-}
-
-void __led_set(led_id_t mask, int state)
-{
- if (STATUS_LED_RED == mask) {
- if (STATUS_LED_ON == state)
- red_led_on();
- else
- red_led_off();
-
- } else if (STATUS_LED_GREEN == mask) {
- if (STATUS_LED_ON == state)
- green_led_on();
- else
- green_led_off();
-
- } else if (STATUS_LED_YELLOW == mask) {
- if (STATUS_LED_ON == state)
- yellow_led_on();
- else
- yellow_led_off();
- }
-}
+++ /dev/null
-/*
- * (C) Copyright 2007-2008
- * Stelian Pop <stelian@popies.net>
- * Lead Tech Design <www.leadtechdesign.com>
- *
- * Achim Ehrlich <aehrlich@taskit.de>
- * taskit GmbH <www.taskit.de>
- *
- * (C) Copyright 2012-
- * Markus Hubig <mhubig@imko.de>
- * IMKO GmbH <www.imko.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/at91sam9260_matrix.h>
-#include <asm/arch/at91sam9_smc.h>
-#include <asm/arch/at91_common.h>
-#include <asm/arch/at91_pmc.h>
-#include <asm/arch/gpio.h>
-#include <watchdog.h>
-
-#ifdef CONFIG_MACB
-# include <net.h>
-# include <netdev.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static void stamp9G20_nand_hw_init(void)
-{
- struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
- struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
- unsigned long csa;
-
- /* Assign CS3 to NAND/SmartMedia Interface */
- csa = readl(&matrix->ebicsa);
- csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
- writel(csa, &matrix->ebicsa);
-
- /* Configure SMC CS3 for NAND/SmartMedia */
- writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
- AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
- &smc->cs[3].setup);
- writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
- AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
- &smc->cs[3].pulse);
- writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
- &smc->cs[3].cycle);
- writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
- AT91_SMC_MODE_EXNW_DISABLE |
- AT91_SMC_MODE_DBW_8 |
- AT91_SMC_MODE_TDF_CYCLE(2),
- &smc->cs[3].mode);
-
- /* Configure RDY/BSY */
- at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
-
- /* Enable NandFlash */
- at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
-}
-
-#ifdef CONFIG_MACB
-static void stamp9G20_macb_hw_init(void)
-{
- struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
-
- /* Enable the PHY Chip via PA26 on the Stamp 2 Adaptor */
- at91_set_gpio_output(AT91_PIN_PA26, 0);
-
- /*
- * Disable pull-up on:
- * RXDV (PA17) => PHY normal mode (not Test mode)
- * ERX0 (PA14) => PHY ADDR0
- * ERX1 (PA15) => PHY ADDR1
- * ERX2 (PA25) => PHY ADDR2
- * ERX3 (PA26) => PHY ADDR3
- * ECRS (PA28) => PHY ADDR4 => PHYADDR = 0x0
- *
- * PHY has internal pull-down
- */
- writel(pin_to_mask(AT91_PIN_PA14) |
- pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA17) |
- pin_to_mask(AT91_PIN_PA18) |
- pin_to_mask(AT91_PIN_PA28),
- &pioa->pudr);
-
- at91_phy_reset();
-
- /* Re-enable pull-up */
- writel(pin_to_mask(AT91_PIN_PA14) |
- pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA17) |
- pin_to_mask(AT91_PIN_PA18) |
- pin_to_mask(AT91_PIN_PA28),
- &pioa->puer);
-
- /* Initialize EMAC=MACB hardware */
- at91_macb_hw_init();
-}
-#endif /* CONFIG_MACB */
-
-int board_early_init_f(void)
-{
- struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
-
- /* Enable clocks for all PIOs */
- writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) |
- (1 << ATMEL_ID_PIOC), &pmc->pcer);
-
- return 0;
-}
-
-int board_postclk_init(void)
-{
- /*
- * Initialize the serial interface here, because be need a running
- * timer to set PC9 to high and wait for some time to enable the
- * level converter of the RS232 interface on the PortuxG20 board.
- */
-
-#ifdef CONFIG_PORTUXG20
- at91_set_gpio_output(AT91_PIN_PC9, 1);
- mdelay(1);
-#endif
- at91_seriald_hw_init();
-
- return 0;
-}
-
-int board_init(void)
-{
- /* Adress of boot parameters */
- gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-
- stamp9G20_nand_hw_init();
-#ifdef CONFIG_MACB
- stamp9G20_macb_hw_init();
-#endif
- return 0;
-}
-
-int dram_init(void)
-{
- gd->ram_size = get_ram_size(
- (void *)CONFIG_SYS_SDRAM_BASE,
- CONFIG_SYS_SDRAM_SIZE);
- return 0;
-}
-
-#ifdef CONFIG_MACB
-int board_eth_init(bd_t *bis)
-{
- return macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x00);
-}
-#endif /* CONFIG_MACB */
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_AT91=y
-CONFIG_TARGET_STAMP9G20=y
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,PORTUXG20"
-# CONFIG_CMD_IMI is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_LOADS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_FPGA is not set
-# CONFIG_CMD_SETEXPR is not set
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_AT91=y
-CONFIG_TARGET_STAMP9G20=y
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20"
-# CONFIG_CMD_IMI is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_LOADS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_FPGA is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_SYS_PROMPT="U-Boot> "
+++ /dev/null
-/*
- * (C) Copyright 2007-2008
- * Stelian Pop <stelian@popies.net>
- * Lead Tech Design <www.leadtechdesign.com>
- *
- * (C) Copyright 2010
- * Achim Ehrlich <aehrlich@taskit.de>
- * taskit GmbH <www.taskit.de>
- *
- * (C) Copyright 2012
- * Markus Hubig <mhubig@imko.de>
- * IMKO GmbH <www.imko.de>
- *
- * Configuation settings for the stamp9g20 CPU module.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * SoC must be defined first, before hardware.h is included.
- * In this case SoC is defined in boards.cfg.
- */
-#include <asm/hardware.h>
-
-/*
- * Warning: changing CONFIG_SYS_TEXT_BASE requires adapting the initial boot
- * program. Since the linker has to swallow that define, we must use a pure
- * hex number here!
- */
-#define CONFIG_SYS_TEXT_BASE 0x23f00000
-
-/* ARM asynchronous clock */
-#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
-#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432MHz crystal */
-
-/* misc settings */
-#define CONFIG_CMDLINE_TAG /* pass commandline to Kernel */
-#define CONFIG_SETUP_MEMORY_TAGS /* pass memory defs to kernel */
-#define CONFIG_INITRD_TAG /* pass initrd param to kernel */
-#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#define CONFIG_BOARD_EARLY_INIT_f /* call board_early_init_f() */
-#define CONFIG_BOARD_POSTCLK_INIT /* call board_postclk_init() */
-#define CONFIG_DISPLAY_CPUINFO /* display CPU Info at startup */
-
-/* setting board specific options */
-#ifdef CONFIG_PORTUXG20
-# define CONFIG_MACH_TYPE MACH_TYPE_PORTUXG20
-# define CONFIG_MACB
-#else
-# define CONFIG_MACH_TYPE MACH_TYPE_STAMP9G20
-#endif
-
-/*
- * SDRAM: 1 bank, 64 MB, base address 0x20000000
- * Already initialized before u-boot gets started.
- */
-#define CONFIG_NR_DRAM_BANKS 1
-#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1
-#define CONFIG_SYS_SDRAM_SIZE (64 << 20)
-
-/*
- * Perform a SDRAM Memtest from the start of SDRAM
- * till the beginning of the U-Boot position in RAM.
- */
-#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE - 0x100000)
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN \
- ROUND(3 * CONFIG_ENV_SIZE + (128 << 10), 0x1000)
-
-/*
- * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM,
- * leaving the correct space for initial global data structure above that
- * address while providing maximum stack area below.
- */
-#define CONFIG_SYS_INIT_SP_ADDR \
- (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE)
-
-/* NAND flash settings */
-#define CONFIG_NAND_ATMEL
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
-#define CONFIG_SYS_NAND_DBW_8
-#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
-#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
-#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
-#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13
-
-/* general purpose I/O */
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-#define CONFIG_AT91_GPIO /* enable the GPIO features */
-#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
-
-/* serial console */
-#define CONFIG_ATMEL_USART
-#define CONFIG_USART_BASE ATMEL_BASE_DBGU
-#define CONFIG_USART_ID ATMEL_ID_SYS
-#define CONFIG_BAUDRATE 115200
-
-/* LED configuration */
-#define CONFIG_STATUS_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-
-/* The LED PINs */
-#define CONFIG_RED_LED AT91_PIN_PC5
-#define CONFIG_GREEN_LED AT91_PIN_PC4
-#define CONFIG_YELLOW_LED AT91_PIN_PC10
-
-#define STATUS_LED_RED 0
-#define STATUS_LED_GREEN 1
-#define STATUS_LED_YELLOW 2
-
-/* Red LED */
-#define STATUS_LED_BIT STATUS_LED_RED
-#define STATUS_LED_STATE STATUS_LED_OFF
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-
-/* Green LED */
-#define STATUS_LED_BIT1 STATUS_LED_GREEN
-#define STATUS_LED_STATE1 STATUS_LED_ON
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
-
-/* Yellow LED */
-#define STATUS_LED_BIT2 STATUS_LED_YELLOW
-#define STATUS_LED_STATE2 STATUS_LED_OFF
-#define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 2)
-
-/* Boot status LED */
-#define STATUS_LED_BOOT STATUS_LED_GREEN
-
-/*
- * Ethernet configuration
- *
- * PortuxG20 has always ethernet but for Stamp9G20 you
- * can enable it here if your baseboard features ethernet.
- */
-
-#define CONFIG_MACB
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_ASIX
-#define CONFIG_USB_ETHER_MCS7830
-
-#ifdef CONFIG_MACB
-# define CONFIG_RMII /* use reduced MII inteface */
-# define CONFIG_NET_RETRY_COUNT 20 /* # of DHCP/BOOTP retries */
-#define CONFIG_AT91_WANTS_COMMON_PHY
-
-/* BOOTP and DHCP options */
-# define CONFIG_BOOTP_BOOTFILESIZE
-# define CONFIG_BOOTP_BOOTPATH
-# define CONFIG_BOOTP_GATEWAY
-# define CONFIG_BOOTP_HOSTNAME
-# define CONFIG_NFSBOOTCOMMAND \
- "setenv autoload yes; setenv autoboot yes; " \
- "setenv bootargs ${basicargs} ${mtdparts} " \
- "root=/dev/nfs ip=dhcp nfsroot=${serverip}:/srv/nfs/rootfs; " \
- "dhcp"
-#endif /* CONFIG_MACB */
-
-/* Enable the watchdog */
-#define CONFIG_AT91SAM9_WATCHDOG
-#define CONFIG_HW_WATCHDOG
-
-/* USB configuration */
-#define CONFIG_USB_ATMEL
-#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SYS_USB_OHCI_CPU_INIT
-#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_UHP_BASE
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
-
-/* General Boot Parameter */
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_BOOTCOMMAND "run flashboot"
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_PBSIZE \
- (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING
-
-/*
- * RAM Memory address where to put the
- * Linux Kernel befor starting.
- */
-#define CONFIG_SYS_LOAD_ADDR 0x22000000
-
-/*
- * The NAND Flash partitions:
- * ==========================================
- * 0x0000000-0x001ffff -> 128k, bootstrap
- * 0x0020000-0x005ffff -> 256k, u-boot
- * 0x0060000-0x007ffff -> 128k, env1
- * 0x0080000-0x009ffff -> 128k, env2 (backup)
- * 0x0100000-0x06fffff -> 6M, kernel
- * 0x0700000-0x8000000 -> 121M, RootFS
- */
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET ((128 + 256) << 10)
-#define CONFIG_ENV_OFFSET_REDUND ((128 + 256 + 128) << 10)
-#define CONFIG_ENV_SIZE (128 << 10)
-
-/*
- * Predefined environment variables.
- * Usefull to define some easy to use boot commands.
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- \
- "basicargs=console=ttyS0,115200\0" \
- \
- "mtdparts=mtdparts=atmel_nand:128k(bootstrap)ro," \
- "256k(uboot)ro,128k(env1)ro," \
- "128k(env2)ro,6M(linux),-(root)rw\0" \
- \
- "flashboot=setenv bootargs ${basicargs} ${mtdparts} " \
- "root=/dev/mtdblock5 rootfstype=jffs2; " \
- "nand read 0x22000000 0x100000 0x600000; " \
- "bootm 22000000\0" \
- \
- "sdboot=setenv bootargs ${basicargs} ${mtdparts} " \
- "root=/dev/mmcblk0p1 rootwait; " \
- "nand read 0x22000000 0x100000 0x600000; " \
- "bootm 22000000"
-
-/* Command line & features configuration */
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_LED
-
-#ifdef CONFIG_MACB
-# define CONFIG_CMD_PING
-# define CONFIG_CMD_DHCP
-#endif /* CONFIG_MACB */
-
-#endif /* __CONFIG_H */
projects / oweals / u-boot.git / commitdiff