board: add support for Vision System's Baltos Industrial PC
authorYegor Yefremov <yegorslists@googlemail.com>
Fri, 29 May 2015 17:27:29 +0000 (19:27 +0200)
committerTom Rini <trini@konsulko.com>
Mon, 15 Jun 2015 14:57:28 +0000 (10:57 -0400)
Vision Systems's Baltos is based on AM335x SoC
from Texas Instruments. This patch adds support
such Industrial PCs in mainline u-boot.

[ balbi@ti.com: updated original patch to current u-boot ]

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
arch/arm/Kconfig
board/vscom/baltos/Kconfig [new file with mode: 0644]
board/vscom/baltos/Makefile [new file with mode: 0644]
board/vscom/baltos/README [new file with mode: 0644]
board/vscom/baltos/board.c [new file with mode: 0644]
board/vscom/baltos/board.h [new file with mode: 0644]
board/vscom/baltos/mux.c [new file with mode: 0644]
board/vscom/baltos/u-boot.lds [new file with mode: 0644]
configs/am335x_baltos_defconfig [new file with mode: 0644]
include/configs/baltos.h [new file with mode: 0644]

index fd47e60a909a7450f391ec1ae78e0ff5cc37770a..ac86518eb02d6ae33614956631da8474a3b66cc3 100644 (file)
@@ -369,6 +369,14 @@ config TARGET_PENGWYN
        select DM_SERIAL
        select DM_GPIO
 
+config TARGET_AM335X_BALTOS
+       bool "Support am335x_baltos"
+       select CPU_V7
+       select SUPPORT_SPL
+       select DM
+       select DM_SERIAL
+       select DM_GPIO
+
 config TARGET_AM335X_EVM
        bool "Support am335x_evm"
        select CPU_V7
@@ -964,6 +972,7 @@ source "board/trizepsiv/Kconfig"
 source "board/ttcontrol/vision2/Kconfig"
 source "board/udoo/Kconfig"
 source "board/vpac270/Kconfig"
+source "board/vscom/baltos/Kconfig"
 source "board/wandboard/Kconfig"
 source "board/warp/Kconfig"
 source "board/woodburn/Kconfig"
diff --git a/board/vscom/baltos/Kconfig b/board/vscom/baltos/Kconfig
new file mode 100644 (file)
index 0000000..bc1edcf
--- /dev/null
@@ -0,0 +1,24 @@
+if TARGET_AM335X_BALTOS
+
+config SYS_BOARD
+       default "baltos"
+
+config SYS_VENDOR
+       default "vscom"
+
+config SYS_SOC
+       default "am33xx"
+
+config SYS_CONFIG_NAME
+       default "baltos"
+
+config CONS_INDEX
+       int "UART used for console"
+       range 1 6
+       default 1
+       help
+         The AM335x SoC has a total of 6 UARTs (UART0 to UART5 as referenced
+         in documentation, etc) available to it.  Depending on your specific
+         board you may want something other than UART0.
+
+endif
diff --git a/board/vscom/baltos/Makefile b/board/vscom/baltos/Makefile
new file mode 100644 (file)
index 0000000..804ac37
--- /dev/null
@@ -0,0 +1,13 @@
+#
+# Makefile
+#
+# Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+#
+# SPDX-License-Identifier:     GPL-2.0+
+#
+
+ifeq ($(CONFIG_SKIP_LOWLEVEL_INIT),)
+obj-y  := mux.o
+endif
+
+obj-y  += board.o
diff --git a/board/vscom/baltos/README b/board/vscom/baltos/README
new file mode 100644 (file)
index 0000000..f744ace
--- /dev/null
@@ -0,0 +1 @@
+BSP for VScom OnRISC Balios family devices, like Balios iR 5221.
diff --git a/board/vscom/baltos/board.c b/board/vscom/baltos/board.c
new file mode 100644 (file)
index 0000000..99ca60e
--- /dev/null
@@ -0,0 +1,474 @@
+/*
+ * board.c
+ *
+ * Board functions for TI AM335X based boards
+ *
+ * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <cpsw.h>
+#include <power/tps65217.h>
+#include <power/tps65910.h>
+#include <environment.h>
+#include <watchdog.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* GPIO that controls power to DDR on EVM-SK */
+#define GPIO_DDR_VTT_EN                7
+#define DIP_S1                 44
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+static int baltos_set_console(void)
+{
+       int val, i, dips = 0;
+       char buf[7];
+
+       for (i = 0; i < 4; i++) {
+               sprintf(buf, "dip_s%d", i + 1);
+
+               if (gpio_request(DIP_S1 + i, buf)) {
+                       printf("failed to export GPIO %d\n", DIP_S1 + i);
+                       return 0;
+               }
+
+               if (gpio_direction_input(DIP_S1 + i)) {
+                       printf("failed to set GPIO %d direction\n", DIP_S1 + i);
+                       return 0;
+               }
+
+               val = gpio_get_value(DIP_S1 + i);
+               dips |= val << i;
+       }
+
+       printf("DIPs: 0x%1x\n", (~dips) & 0xf);
+
+       if ((dips & 0xf) == 0xe)
+               setenv("console", "ttyUSB0,115200n8");
+
+       return 0;
+}
+
+static int read_eeprom(BSP_VS_HWPARAM *header)
+{
+       i2c_set_bus_num(1);
+
+       /* Check if baseboard eeprom is available */
+       if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) {
+               puts("Could not probe the EEPROM; something fundamentally "
+                       "wrong on the I2C bus.\n");
+               return -ENODEV;
+       }
+
+       /* read the eeprom using i2c */
+       if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header,
+                    sizeof(BSP_VS_HWPARAM))) {
+               puts("Could not read the EEPROM; something fundamentally"
+                       " wrong on the I2C bus.\n");
+               return -EIO;
+       }
+
+       if (header->Magic != 0xDEADBEEF) {
+
+               printf("Incorrect magic number (0x%x) in EEPROM\n",
+                               header->Magic);
+
+               /* fill default values */
+               header->SystemId = 211;
+               header->MAC1[0] = 0x00;
+               header->MAC1[1] = 0x00;
+               header->MAC1[2] = 0x00;
+               header->MAC1[3] = 0x00;
+               header->MAC1[4] = 0x00;
+               header->MAC1[5] = 0x01;
+
+               header->MAC2[0] = 0x00;
+               header->MAC2[1] = 0x00;
+               header->MAC2[2] = 0x00;
+               header->MAC2[3] = 0x00;
+               header->MAC2[4] = 0x00;
+               header->MAC2[5] = 0x02;
+
+               header->MAC3[0] = 0x00;
+               header->MAC3[1] = 0x00;
+               header->MAC3[2] = 0x00;
+               header->MAC3[3] = 0x00;
+               header->MAC3[4] = 0x00;
+               header->MAC3[5] = 0x03;
+       }
+
+       return 0;
+}
+
+#if defined(CONFIG_SPL_BUILD) || defined(CONFIG_NOR_BOOT)
+
+static const struct ddr_data ddr3_baltos_data = {
+       .datardsratio0 = MT41K256M16HA125E_RD_DQS,
+       .datawdsratio0 = MT41K256M16HA125E_WR_DQS,
+       .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
+       .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
+};
+
+static const struct cmd_control ddr3_baltos_cmd_ctrl_data = {
+       .cmd0csratio = MT41K256M16HA125E_RATIO,
+       .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+       .cmd1csratio = MT41K256M16HA125E_RATIO,
+       .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+       .cmd2csratio = MT41K256M16HA125E_RATIO,
+       .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_baltos_emif_reg_data = {
+       .sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
+       .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
+       .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
+       .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
+       .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
+       .zq_config = MT41K256M16HA125E_ZQ_CFG,
+       .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
+};
+
+#ifdef CONFIG_SPL_OS_BOOT
+int spl_start_uboot(void)
+{
+       /* break into full u-boot on 'c' */
+       return (serial_tstc() && serial_getc() == 'c');
+}
+#endif
+
+#define OSC    (V_OSCK/1000000)
+const struct dpll_params dpll_ddr = {
+               266, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_evm_sk = {
+               303, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_baltos = {
+               400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+       int mpu_vdd;
+       int sil_rev;
+
+       /* Get the frequency */
+       dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
+
+       /*
+        * The GP EVM, IDK and EVM SK use a TPS65910 PMIC.  For all
+        * MPU frequencies we support we use a CORE voltage of
+        * 1.1375V.  For MPU voltage we need to switch based on
+        * the frequency we are running at.
+        */
+       i2c_set_bus_num(1);
+
+       if (i2c_probe(TPS65910_CTRL_I2C_ADDR)) {
+               puts("i2c: cannot access TPS65910\n");
+               return;
+       }
+
+       /*
+        * Depending on MPU clock and PG we will need a different
+        * VDD to drive at that speed.
+        */
+       sil_rev = readl(&cdev->deviceid) >> 28;
+       mpu_vdd = am335x_get_tps65910_mpu_vdd(sil_rev,
+                                             dpll_mpu_opp100.m);
+
+       /* Tell the TPS65910 to use i2c */
+       tps65910_set_i2c_control();
+
+       /* First update MPU voltage. */
+       if (tps65910_voltage_update(MPU, mpu_vdd))
+               return;
+
+       /* Second, update the CORE voltage. */
+       if (tps65910_voltage_update(CORE, TPS65910_OP_REG_SEL_1_1_3))
+               return;
+
+       /* Set CORE Frequencies to OPP100 */
+       do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+       /* Set MPU Frequency to what we detected now that voltages are set */
+       do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+
+       writel(0x000010ff, PRM_DEVICE_INST + 4);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+       enable_i2c1_pin_mux();
+       i2c_set_bus_num(1);
+
+       return &dpll_ddr_baltos;
+}
+
+void set_uart_mux_conf(void)
+{
+       enable_uart0_pin_mux();
+}
+
+void set_mux_conf_regs(void)
+{
+       enable_board_pin_mux();
+}
+
+const struct ctrl_ioregs ioregs_baltos = {
+       .cm0ioctl               = MT41K256M16HA125E_IOCTRL_VALUE,
+       .cm1ioctl               = MT41K256M16HA125E_IOCTRL_VALUE,
+       .cm2ioctl               = MT41K256M16HA125E_IOCTRL_VALUE,
+       .dt0ioctl               = MT41K256M16HA125E_IOCTRL_VALUE,
+       .dt1ioctl               = MT41K256M16HA125E_IOCTRL_VALUE,
+};
+
+void sdram_init(void)
+{
+       gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en");
+       gpio_direction_output(GPIO_DDR_VTT_EN, 1);
+
+       config_ddr(400, &ioregs_baltos,
+                  &ddr3_baltos_data,
+                  &ddr3_baltos_cmd_ctrl_data,
+                  &ddr3_baltos_emif_reg_data, 0);
+}
+#endif
+
+/*
+ * Basic board specific setup.  Pinmux has been handled already.
+ */
+int board_init(void)
+{
+#if defined(CONFIG_HW_WATCHDOG)
+       hw_watchdog_init();
+#endif
+
+       gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+#if defined(CONFIG_NOR) || defined(CONFIG_NAND)
+       gpmc_init();
+#endif
+       return 0;
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+       int node, ret;
+       unsigned char mac_addr[6];
+       BSP_VS_HWPARAM header;
+
+       /* get production data */
+       if (read_eeprom(&header))
+               return 0;
+
+       /* setup MAC1 */
+       mac_addr[0] = header.MAC1[0];
+       mac_addr[1] = header.MAC1[1];
+       mac_addr[2] = header.MAC1[2];
+       mac_addr[3] = header.MAC1[3];
+       mac_addr[4] = header.MAC1[4];
+       mac_addr[5] = header.MAC1[5];
+
+
+       node = fdt_path_offset(blob, "/ocp/ethernet/slave@4a100200");
+       if (node < 0) {
+               printf("no /soc/fman/ethernet path offset\n");
+               return -ENODEV;
+       }
+
+       ret = fdt_setprop(blob, node, "mac-address", &mac_addr, 6);
+       if (ret) {
+               printf("error setting local-mac-address property\n");
+               return -ENODEV;
+       }
+
+       /* setup MAC2 */
+       mac_addr[0] = header.MAC2[0];
+       mac_addr[1] = header.MAC2[1];
+       mac_addr[2] = header.MAC2[2];
+       mac_addr[3] = header.MAC2[3];
+       mac_addr[4] = header.MAC2[4];
+       mac_addr[5] = header.MAC2[5];
+
+       node = fdt_path_offset(blob, "/ocp/ethernet/slave@4a100300");
+       if (node < 0) {
+               printf("no /soc/fman/ethernet path offset\n");
+               return -ENODEV;
+       }
+
+       ret = fdt_setprop(blob, node, "mac-address", &mac_addr, 6);
+       if (ret) {
+               printf("error setting local-mac-address property\n");
+               return -ENODEV;
+       }
+
+       printf("\nFDT was successfully setup\n");
+
+       return 0;
+}
+
+static struct module_pin_mux dip_pin_mux[] = {
+       {OFFSET(gpmc_ad12), (MODE(7) | RXACTIVE )},     /* GPIO1_12 */
+       {OFFSET(gpmc_ad13), (MODE(7)  | RXACTIVE )},    /* GPIO1_13 */
+       {OFFSET(gpmc_ad14), (MODE(7)  | RXACTIVE )},    /* GPIO1_14 */
+       {OFFSET(gpmc_ad15), (MODE(7)  | RXACTIVE )},    /* GPIO1_15 */
+       {-1},
+};
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+       BSP_VS_HWPARAM header;
+       char model[4];
+
+       /* get production data */
+       if (read_eeprom(&header)) {
+               sprintf(model, "211");
+       } else {
+               sprintf(model, "%d", header.SystemId);
+               if (header.SystemId == 215) {
+                       configure_module_pin_mux(dip_pin_mux);
+                       baltos_set_console();
+               }
+       }
+       setenv("board_name", model);
+#endif
+
+       return 0;
+}
+#endif
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+       (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+static void cpsw_control(int enabled)
+{
+       /* VTP can be added here */
+
+       return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+       {
+               .slave_reg_ofs  = 0x208,
+               .sliver_reg_ofs = 0xd80,
+               .phy_addr       = 0,
+       },
+       {
+               .slave_reg_ofs  = 0x308,
+               .sliver_reg_ofs = 0xdc0,
+               .phy_addr       = 7,
+       },
+};
+
+static struct cpsw_platform_data cpsw_data = {
+       .mdio_base              = CPSW_MDIO_BASE,
+       .cpsw_base              = CPSW_BASE,
+       .mdio_div               = 0xff,
+       .channels               = 8,
+       .cpdma_reg_ofs          = 0x800,
+       .slaves                 = 2,
+       .slave_data             = cpsw_slaves,
+       .active_slave           = 1,
+       .ale_reg_ofs            = 0xd00,
+       .ale_entries            = 1024,
+       .host_port_reg_ofs      = 0x108,
+       .hw_stats_reg_ofs       = 0x900,
+       .bd_ram_ofs             = 0x2000,
+       .mac_control            = (1 << 5),
+       .control                = cpsw_control,
+       .host_port_num          = 0,
+       .version                = CPSW_CTRL_VERSION_2,
+};
+#endif
+
+#if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USBETH_SUPPORT)) \
+               && defined(CONFIG_SPL_BUILD)) || \
+       ((defined(CONFIG_DRIVER_TI_CPSW) || \
+         defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)) && \
+        !defined(CONFIG_SPL_BUILD))
+int board_eth_init(bd_t *bis)
+{
+       int rv, n = 0;
+       uint8_t mac_addr[6];
+       uint32_t mac_hi, mac_lo;
+       __maybe_unused struct am335x_baseboard_id header;
+
+       /*
+        * Note here that we're using CPSW1 since that has a 1Gbit PHY while
+        * CSPW0 has a 100Mbit PHY.
+        *
+        * On product, CPSW1 maps to port labeled WAN.
+        */
+
+       /* try reading mac address from efuse */
+       mac_lo = readl(&cdev->macid1l);
+       mac_hi = readl(&cdev->macid1h);
+       mac_addr[0] = mac_hi & 0xFF;
+       mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+       mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+       mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+       mac_addr[4] = mac_lo & 0xFF;
+       mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+       (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+       if (!getenv("ethaddr")) {
+               printf("<ethaddr> not set. Validating first E-fuse MAC\n");
+
+               if (is_valid_ethaddr(mac_addr))
+                       eth_setenv_enetaddr("ethaddr", mac_addr);
+       }
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+       writel((GMII1_SEL_RMII | GMII2_SEL_RGMII | RGMII2_IDMODE), &cdev->miisel);
+       cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_RGMII;
+       rv = cpsw_register(&cpsw_data);
+       if (rv < 0)
+               printf("Error %d registering CPSW switch\n", rv);
+       else
+               n += rv;
+#endif
+
+       /*
+        *
+        * CPSW RGMII Internal Delay Mode is not supported in all PVT
+        * operating points.  So we must set the TX clock delay feature
+        * in the AR8051 PHY.  Since we only support a single ethernet
+        * device in U-Boot, we only do this for the first instance.
+        */
+#define AR8051_PHY_DEBUG_ADDR_REG      0x1d
+#define AR8051_PHY_DEBUG_DATA_REG      0x1e
+#define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5
+#define AR8051_RGMII_TX_CLK_DLY                0x100
+       const char *devname;
+       devname = miiphy_get_current_dev();
+
+       miiphy_write(devname, 0x7, AR8051_PHY_DEBUG_ADDR_REG,
+                       AR8051_DEBUG_RGMII_CLK_DLY_REG);
+       miiphy_write(devname, 0x7, AR8051_PHY_DEBUG_DATA_REG,
+                       AR8051_RGMII_TX_CLK_DLY);
+#endif
+       return n;
+}
+#endif
diff --git a/board/vscom/baltos/board.h b/board/vscom/baltos/board.h
new file mode 100644 (file)
index 0000000..bcdb648
--- /dev/null
@@ -0,0 +1,90 @@
+/*
+ * board.h
+ *
+ * TI AM335x boards information header
+ *
+ * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * TI AM335x parts define a system EEPROM that defines certain sub-fields.
+ * We use these fields to in turn see what board we are on, and what
+ * that might require us to set or not set.
+ */
+#define HDR_NO_OF_MAC_ADDR     3
+#define HDR_ETH_ALEN           6
+#define HDR_NAME_LEN           8
+
+struct am335x_baseboard_id {
+       unsigned int  magic;
+       char name[HDR_NAME_LEN];
+       char version[4];
+       char serial[12];
+       char config[32];
+       char mac_addr[HDR_NO_OF_MAC_ADDR][HDR_ETH_ALEN];
+};
+
+typedef struct _BSP_VS_HWPARAM    // v1.0
+{
+       uint32_t Magic;
+       uint32_t HwRev;
+       uint32_t SerialNumber;
+       char PrdDate[11];    // as a string ie. "01.01.2006"
+       uint16_t SystemId;
+       uint8_t MAC1[6];        // internal EMAC
+       uint8_t MAC2[6];        // SMSC9514
+       uint8_t MAC3[6];        // WL1271 WLAN
+} __attribute__ ((packed)) BSP_VS_HWPARAM;
+
+static inline int board_is_bone(struct am335x_baseboard_id *header)
+{
+       return !strncmp(header->name, "A335BONE", HDR_NAME_LEN);
+}
+
+static inline int board_is_bone_lt(struct am335x_baseboard_id *header)
+{
+       return !strncmp(header->name, "A335BNLT", HDR_NAME_LEN);
+}
+
+static inline int board_is_evm_sk(struct am335x_baseboard_id *header)
+{
+       return !strncmp("A335X_SK", header->name, HDR_NAME_LEN);
+}
+
+static inline int board_is_idk(struct am335x_baseboard_id *header)
+{
+       return !strncmp(header->config, "SKU#02", 6);
+}
+
+static inline int board_is_gp_evm(struct am335x_baseboard_id *header)
+{
+       return !strncmp("A33515BB", header->name, HDR_NAME_LEN);
+}
+
+static inline int board_is_evm_15_or_later(struct am335x_baseboard_id *header)
+{
+       return (board_is_gp_evm(header) &&
+               strncmp("1.5", header->version, 3) <= 0);
+}
+
+/*
+ * We have three pin mux functions that must exist.  We must be able to enable
+ * uart0, for initial output and i2c0 to read the main EEPROM.  We then have a
+ * main pinmux function that can be overridden to enable all other pinmux that
+ * is required on the board.
+ */
+void enable_uart0_pin_mux(void);
+void enable_uart1_pin_mux(void);
+void enable_uart2_pin_mux(void);
+void enable_uart3_pin_mux(void);
+void enable_uart4_pin_mux(void);
+void enable_uart5_pin_mux(void);
+void enable_i2c0_pin_mux(void);
+void enable_i2c1_pin_mux(void);
+void enable_board_pin_mux(void);
+#endif
diff --git a/board/vscom/baltos/mux.c b/board/vscom/baltos/mux.c
new file mode 100644 (file)
index 0000000..8783b25
--- /dev/null
@@ -0,0 +1,194 @@
+/*
+ * mux.c
+ *
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <i2c.h>
+#include "board.h"
+
+static struct module_pin_mux uart0_pin_mux[] = {
+       {OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)},  /* UART0_RXD */
+       {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},              /* UART0_TXD */
+       {-1},
+};
+
+static struct module_pin_mux uart1_pin_mux[] = {
+       {OFFSET(uart1_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)},  /* UART1_RXD */
+       {OFFSET(uart1_txd), (MODE(0) | PULLUDEN)},              /* UART1_TXD */
+       {-1},
+};
+
+static struct module_pin_mux uart2_pin_mux[] = {
+       {OFFSET(spi0_sclk), (MODE(1) | PULLUP_EN | RXACTIVE)},  /* UART2_RXD */
+       {OFFSET(spi0_d0), (MODE(1) | PULLUDEN)},                /* UART2_TXD */
+       {-1},
+};
+
+static struct module_pin_mux uart3_pin_mux[] = {
+       {OFFSET(spi0_cs1), (MODE(1) | PULLUP_EN | RXACTIVE)},   /* UART3_RXD */
+       {OFFSET(ecap0_in_pwm0_out), (MODE(1) | PULLUDEN)},      /* UART3_TXD */
+       {-1},
+};
+
+static struct module_pin_mux uart4_pin_mux[] = {
+       {OFFSET(gpmc_wait0), (MODE(6) | PULLUP_EN | RXACTIVE)}, /* UART4_RXD */
+       {OFFSET(gpmc_wpn), (MODE(6) | PULLUDEN)},               /* UART4_TXD */
+       {-1},
+};
+
+static struct module_pin_mux uart5_pin_mux[] = {
+       {OFFSET(lcd_data9), (MODE(4) | PULLUP_EN | RXACTIVE)},  /* UART5_RXD */
+       {OFFSET(lcd_data8), (MODE(4) | PULLUDEN)},              /* UART5_TXD */
+       {-1},
+};
+
+static struct module_pin_mux mmc0_pin_mux[] = {
+       {OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_DAT3 */
+       {OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_DAT2 */
+       {OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_DAT1 */
+       {OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_DAT0 */
+       {OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)},   /* MMC0_CLK */
+       {OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)},   /* MMC0_CMD */
+       //{OFFSET(spi0_cs1), (MODE(5) | RXACTIVE | PULLUP_EN)}, /* MMC0_CD */
+       {-1},
+};
+
+static struct module_pin_mux i2c0_pin_mux[] = {
+       {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE |
+                       PULLUDEN | SLEWCTRL)}, /* I2C_DATA */
+       {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE |
+                       PULLUDEN | SLEWCTRL)}, /* I2C_SCLK */
+       {-1},
+};
+
+static struct module_pin_mux i2c1_pin_mux[] = {
+       {OFFSET(spi0_d1), (MODE(2) | RXACTIVE |
+                       PULLUDEN | SLEWCTRL)},  /* I2C_DATA */
+       {OFFSET(spi0_cs0), (MODE(2) | RXACTIVE |
+                       PULLUDEN | SLEWCTRL)},  /* I2C_SCLK */
+       {-1},
+};
+
+static struct module_pin_mux gpio0_7_pin_mux[] = {
+       {OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDEN)},      /* GPIO0_7 */
+       {-1},
+};
+
+static struct module_pin_mux rmii1_pin_mux[] = {
+       {OFFSET(mii1_crs), MODE(1) | RXACTIVE},                 /* RGMII1_TCTL */
+       {OFFSET(mii1_txen), MODE(1)},                   /* RGMII1_TCTL */
+       {OFFSET(mii1_txd1), MODE(1)},                   /* RGMII1_TCTL */
+       {OFFSET(mii1_txd0), MODE(1)},                   /* RGMII1_TCTL */
+       {OFFSET(mii1_rxd1), MODE(1) | RXACTIVE},                        /* RGMII1_TCTL */
+       {OFFSET(mii1_rxd0), MODE(1) | RXACTIVE},                        /* RGMII1_TCTL */
+       {OFFSET(rmii1_refclk), MODE(0) | RXACTIVE},                     /* RGMII1_TCTL */
+       {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */
+       {OFFSET(mdio_clk), MODE(0) | PULLUP_EN},        /* MDIO_CLK */
+       {-1},
+};
+
+static struct module_pin_mux rgmii2_pin_mux[] = {
+       {OFFSET(gpmc_a0), MODE(2)},                     /* RGMII1_TCTL */
+       {OFFSET(gpmc_a1), MODE(2) | RXACTIVE},  /* RGMII1_RCTL */
+       {OFFSET(gpmc_a2), MODE(2)},                     /* RGMII1_TD3 */
+       {OFFSET(gpmc_a3), MODE(2)},                     /* RGMII1_TD2 */
+       {OFFSET(gpmc_a4), MODE(2)},                     /* RGMII1_TD1 */
+       {OFFSET(gpmc_a5), MODE(2)},                     /* RGMII1_TD0 */
+       {OFFSET(gpmc_a6), MODE(2)},                     /* RGMII1_TCLK */
+       {OFFSET(gpmc_a7), MODE(2) | RXACTIVE},  /* RGMII1_RCLK */
+       {OFFSET(gpmc_a8), MODE(2) | RXACTIVE},  /* RGMII1_RD3 */
+       {OFFSET(gpmc_a9), MODE(2) | RXACTIVE},  /* RGMII1_RD2 */
+       {OFFSET(gpmc_a10), MODE(2) | RXACTIVE}, /* RGMII1_RD1 */
+       {OFFSET(gpmc_a11), MODE(2) | RXACTIVE}, /* RGMII1_RD0 */
+       {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */
+       {OFFSET(mdio_clk), MODE(0) | PULLUP_EN},        /* MDIO_CLK */
+       {-1},
+};
+
+static struct module_pin_mux nand_pin_mux[] = {
+       {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)},   /* NAND AD0 */
+       {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)},   /* NAND AD1 */
+       {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)},   /* NAND AD2 */
+       {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)},   /* NAND AD3 */
+       {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)},   /* NAND AD4 */
+       {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)},   /* NAND AD5 */
+       {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)},   /* NAND AD6 */
+       {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)},   /* NAND AD7 */
+       {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
+       {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)},   /* NAND_WPN */
+       {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)},      /* NAND_CS0 */
+       {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
+       {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)},   /* NAND_OE */
+       {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)},       /* NAND_WEN */
+       {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)},  /* NAND_BE_CLE */
+       {-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+       configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_uart1_pin_mux(void)
+{
+       configure_module_pin_mux(uart1_pin_mux);
+}
+
+void enable_uart2_pin_mux(void)
+{
+       configure_module_pin_mux(uart2_pin_mux);
+}
+
+void enable_uart3_pin_mux(void)
+{
+       configure_module_pin_mux(uart3_pin_mux);
+}
+
+void enable_uart4_pin_mux(void)
+{
+       configure_module_pin_mux(uart4_pin_mux);
+}
+
+void enable_uart5_pin_mux(void)
+{
+       configure_module_pin_mux(uart5_pin_mux);
+}
+
+void enable_i2c0_pin_mux(void)
+{
+       configure_module_pin_mux(i2c0_pin_mux);
+}
+
+void enable_i2c1_pin_mux(void)
+{
+       configure_module_pin_mux(i2c1_pin_mux);
+}
+
+void enable_board_pin_mux()
+{
+       /* Baltos */
+       configure_module_pin_mux(i2c1_pin_mux);
+       configure_module_pin_mux(gpio0_7_pin_mux);
+       configure_module_pin_mux(rgmii2_pin_mux);
+       configure_module_pin_mux(rmii1_pin_mux);
+       configure_module_pin_mux(mmc0_pin_mux);
+
+#if defined(CONFIG_NAND)
+       configure_module_pin_mux(nand_pin_mux);
+#endif
+}
diff --git a/board/vscom/baltos/u-boot.lds b/board/vscom/baltos/u-boot.lds
new file mode 100644 (file)
index 0000000..315ba5b
--- /dev/null
@@ -0,0 +1,128 @@
+/*
+ * Copyright (c) 2004-2008 Texas Instruments
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+       . = 0x00000000;
+
+       . = ALIGN(4);
+       .text :
+       {
+               *(.__image_copy_start)
+               *(.vectors)
+               CPUDIR/start.o (.text*)
+               board/vscom/baltos/built-in.o (.text*)
+               *(.text*)
+       }
+
+       . = ALIGN(4);
+       .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+       . = ALIGN(4);
+       .data : {
+               *(.data*)
+       }
+
+       . = ALIGN(4);
+
+       . = .;
+
+       . = ALIGN(4);
+       .u_boot_list : {
+               KEEP(*(SORT(.u_boot_list*)));
+       }
+
+       . = ALIGN(4);
+
+       .image_copy_end :
+       {
+               *(.__image_copy_end)
+       }
+
+       .rel_dyn_start :
+       {
+               *(.__rel_dyn_start)
+       }
+
+       .rel.dyn : {
+               *(.rel*)
+       }
+
+       .rel_dyn_end :
+       {
+               *(.__rel_dyn_end)
+       }
+
+       .hash : { *(.hash*) }
+
+       .end :
+       {
+               *(.__end)
+       }
+
+       _image_binary_end = .;
+
+       /*
+        * Deprecated: this MMU section is used by pxa at present but
+        * should not be used by new boards/CPUs.
+        */
+       . = ALIGN(4096);
+       .mmutable : {
+               *(.mmutable)
+       }
+
+/*
+ * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
+ * __bss_base and __bss_limit are for linker only (overlay ordering)
+ */
+
+       .bss_start __rel_dyn_start (OVERLAY) : {
+               KEEP(*(.__bss_start));
+               __bss_base = .;
+       }
+
+       .bss __bss_base (OVERLAY) : {
+               *(.bss*)
+                . = ALIGN(4);
+                __bss_limit = .;
+       }
+
+       .bss_end __bss_limit (OVERLAY) : {
+               KEEP(*(.__bss_end));
+       }
+
+       .dynsym _image_binary_end : { *(.dynsym) }
+       .dynbss : { *(.dynbss) }
+       .dynstr : { *(.dynstr*) }
+       .dynamic : { *(.dynamic*) }
+       .gnu.hash : { *(.gnu.hash) }
+       .plt : { *(.plt*) }
+       .interp : { *(.interp*) }
+       .gnu : { *(.gnu*) }
+       .ARM.exidx : { *(.ARM.exidx*) }
+}
diff --git a/configs/am335x_baltos_defconfig b/configs/am335x_baltos_defconfig
new file mode 100644 (file)
index 0000000..679b04f
--- /dev/null
@@ -0,0 +1,7 @@
+CONFIG_SPL=y
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_STACK_R_ADDR=0x82000000
+CONFIG_SYS_EXTRA_OPTIONS="NAND"
+CONFIG_CONS_INDEX=1
+CONFIG_ARM=y
+CONFIG_TARGET_AM335X_BALTOS=y
diff --git a/include/configs/baltos.h b/include/configs/baltos.h
new file mode 100644 (file)
index 0000000..6242895
--- /dev/null
@@ -0,0 +1,340 @@
+/*
+ * am335x_evm.h
+ *
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __CONFIG_BALTOS_H
+#define __CONFIG_BALTOS_H
+
+#include <configs/ti_am335x_common.h>
+
+#define MACH_TYPE_TIAM335EVM           3589    /* Until the next sync */
+#define CONFIG_MACH_TYPE               MACH_TYPE_TIAM335EVM
+#define CONFIG_BOARD_LATE_INIT
+
+/* Clock Defines */
+#define V_OSCK                         24000000  /* Clock output from T2 */
+#define V_SCLK                         (V_OSCK)
+
+/* Custom script for NOR */
+#define CONFIG_SYS_LDSCRIPT            "board/vscom/baltos/u-boot.lds"
+
+/* Always 128 KiB env size */
+#define CONFIG_ENV_SIZE                        (128 << 10)
+
+/* Enhance our eMMC support / experience. */
+#define CONFIG_CMD_GPT
+#define CONFIG_EFI_PARTITION
+#define CONFIG_PARTITION_UUIDS
+#define CONFIG_CMD_PART
+
+/* FIT support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE     1 /* enable fit_format_{error,warning}() */
+#define CONFIG_OF_BOARD_SETUP
+
+/* UBI Support */
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+
+/* I2C configuration */
+#undef CONFIG_SYS_OMAP24_I2C_SPEED
+#define CONFIG_SYS_OMAP24_I2C_SPEED 10000
+
+#ifdef CONFIG_NAND
+#define CONFIG_SYS_NAND_U_BOOT_OFFS    0x000c0000
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS 0x00080000 /* os parameters */
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00200000 /* kernel offset */
+#define CONFIG_CMD_SPL_WRITE_SIZE      0x2000
+#endif
+#define NANDARGS \
+       "mtdids=" MTDIDS_DEFAULT "\0" \
+       "mtdparts=" MTDPARTS_DEFAULT "\0" \
+       "nandargs=setenv bootargs console=${console} " \
+               "${optargs} " \
+               "${mtdparts} " \
+               "root=${nandroot} " \
+               "rootfstype=${nandrootfstype}\0" \
+       "nandroot=ubi0:rootfs rw ubi.mtd=5\0" \
+       "nandrootfstype=ubifs rootwait=1\0" \
+       "nandboot=echo Booting from nand ...; " \
+               "run nandargs; " \
+               "setenv loadaddr 0x84000000; " \
+               "ubi part UBI; " \
+               "ubifsmount ubi0:kernel; " \
+               "ubifsload $loadaddr kernel-fit.itb;" \
+               "ubifsumount; " \
+               "bootm ${loadaddr}#conf${board_name}\0"
+#else
+#define NANDARGS ""
+#endif
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_EXTRA_ENV_SETTINGS \
+       DEFAULT_LINUX_BOOT_ENV \
+       "boot_fdt=try\0" \
+       "bootpart=0:2\0" \
+       "bootdir=/boot\0" \
+       "bootfile=zImage\0" \
+       "fdtfile=undefined\0" \
+       "console=ttyO0,115200n8\0" \
+       "partitions=" \
+               "uuid_disk=${uuid_gpt_disk};" \
+               "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}\0" \
+       "optargs=\0" \
+       "mmcdev=0\0" \
+       "mmcroot=/dev/mmcblk0p2 ro\0" \
+       "mmcrootfstype=ext4 rootwait\0" \
+       "rootpath=/export/rootfs\0" \
+       "nfsopts=nolock\0" \
+       "static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
+               "::off\0" \
+       "ramroot=/dev/ram0 rw\0" \
+       "ramrootfstype=ext2\0" \
+       "mmcargs=setenv bootargs console=${console} " \
+               "${optargs} " \
+               "${mtdparts} " \
+               "root=${mmcroot} " \
+               "rootfstype=${mmcrootfstype}\0" \
+       "spiroot=/dev/mtdblock4 rw\0" \
+       "spirootfstype=jffs2\0" \
+       "spisrcaddr=0xe0000\0" \
+       "spiimgsize=0x362000\0" \
+       "spibusno=0\0" \
+       "spiargs=setenv bootargs console=${console} " \
+               "${optargs} " \
+               "root=${spiroot} " \
+               "rootfstype=${spirootfstype}\0" \
+       "netargs=setenv bootargs console=${console} " \
+               "${optargs} " \
+               "root=/dev/nfs " \
+               "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
+               "ip=dhcp\0" \
+       "bootenv=uEnv.txt\0" \
+       "loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
+       "importbootenv=echo Importing environment from mmc ...; " \
+               "env import -t $loadaddr $filesize\0" \
+       "ramargs=setenv bootargs console=${console} " \
+               "${optargs} " \
+               "root=${ramroot} " \
+               "rootfstype=${ramrootfstype}\0" \
+       "loadramdisk=load mmc ${mmcdev} ${rdaddr} ramdisk.gz\0" \
+       "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
+       "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
+       "mmcloados=run mmcargs; " \
+               "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+                       "if run loadfdt; then " \
+                               "bootz ${loadaddr} - ${fdtaddr}; " \
+                       "else " \
+                               "if test ${boot_fdt} = try; then " \
+                                       "bootz; " \
+                               "else " \
+                                       "echo WARN: Cannot load the DT; " \
+                               "fi; " \
+                       "fi; " \
+               "else " \
+                       "bootz; " \
+               "fi;\0" \
+       "mmcboot=mmc dev ${mmcdev}; " \
+               "if mmc rescan; then " \
+                       "echo SD/MMC found on device ${mmcdev};" \
+                       "if run loadbootenv; then " \
+                               "echo Loaded environment from ${bootenv};" \
+                               "run importbootenv;" \
+                       "fi;" \
+                       "if test -n $uenvcmd; then " \
+                               "echo Running uenvcmd ...;" \
+                               "run uenvcmd;" \
+                       "fi;" \
+                       "if run loadimage; then " \
+                               "run mmcloados;" \
+                       "fi;" \
+               "fi;\0" \
+       "spiboot=echo Booting from spi ...; " \
+               "run spiargs; " \
+               "sf probe ${spibusno}:0; " \
+               "sf read ${loadaddr} ${spisrcaddr} ${spiimgsize}; " \
+               "bootz ${loadaddr}\0" \
+       "netboot=echo Booting from network ...; " \
+               "setenv autoload no; " \
+               "dhcp; " \
+               "tftp ${loadaddr} ${bootfile}; " \
+               "tftp ${fdtaddr} ${fdtfile}; " \
+               "run netargs; " \
+               "bootz ${loadaddr} - ${fdtaddr}\0" \
+       "ramboot=echo Booting from ramdisk ...; " \
+               "run ramargs; " \
+               "bootz ${loadaddr} ${rdaddr} ${fdtaddr}\0" \
+       "findfdt=setenv fdtfile am335x-baltos.dtb\0" \
+       NANDARGS
+       /*DFUARGS*/
+#endif
+
+#define CONFIG_BOOTCOMMAND \
+       "run findfdt; " \
+       "run mmcboot;" \
+       "setenv mmcdev 1; " \
+       "setenv bootpart 1:2; " \
+       "run mmcboot;" \
+       "run nandboot;"
+
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_NFS
+
+/* NS16550 Configuration */
+#define CONFIG_SYS_NS16550_COM1                0x44e09000      /* Base EVM has UART0 */
+#define CONFIG_SYS_NS16550_COM2                0x48022000      /* UART1 */
+#define CONFIG_SYS_NS16550_COM3                0x48024000      /* UART2 */
+#define CONFIG_SYS_NS16550_COM4                0x481a6000      /* UART3 */
+#define CONFIG_SYS_NS16550_COM5                0x481a8000      /* UART4 */
+#define CONFIG_SYS_NS16550_COM6                0x481aa000      /* UART5 */
+#define CONFIG_BAUDRATE                        115200
+
+#define CONFIG_CMD_EEPROM
+#define CONFIG_ENV_EEPROM_IS_ON_I2C
+#define CONFIG_SYS_I2C_EEPROM_ADDR     0x50    /* Main EEPROM */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+
+/* PMIC support */
+#define CONFIG_POWER_TPS65910
+
+/* SPL */
+#ifndef CONFIG_NOR_BOOT
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_YMODEM_SUPPORT
+
+/* Bootcount using the RTC block */
+#define CONFIG_BOOTCOUNT_LIMIT
+#define CONFIG_BOOTCOUNT_AM33XX
+
+/* USB gadget RNDIS */
+/*#define CONFIG_SPL_MUSB_NEW_SUPPORT*/
+
+/* General network SPL, both CPSW and USB gadget RNDIS */
+/*#define CONFIG_SPL_NET_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_NET_VCI_STRING      "AM335x U-Boot SPL"*/
+
+#define CONFIG_SPL_LDSCRIPT            "$(CPUDIR)/am33xx/u-boot-spl.lds"
+
+#ifdef CONFIG_NAND
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT     (CONFIG_SYS_NAND_BLOCK_SIZE / \
+                                        CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_PAGE_SIZE      2048
+#define CONFIG_SYS_NAND_OOBSIZE                64
+#define CONFIG_SYS_NAND_BLOCK_SIZE     (128*1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS  NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS         { 2, 3, 4, 5, 6, 7, 8, 9, \
+                                        10, 11, 12, 13, 14, 15, 16, 17, \
+                                        18, 19, 20, 21, 22, 23, 24, 25, \
+                                        26, 27, 28, 29, 30, 31, 32, 33, \
+                                        34, 35, 36, 37, 38, 39, 40, 41, \
+                                        42, 43, 44, 45, 46, 47, 48, 49, \
+                                        50, 51, 52, 53, 54, 55, 56, 57, }
+
+#define CONFIG_SYS_NAND_ECCSIZE                512
+#define CONFIG_SYS_NAND_ECCBYTES       14
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_NAND_OMAP_ECCSCHEME     OMAP_ECC_BCH8_CODE_HW
+#define CONFIG_SYS_NAND_U_BOOT_START   CONFIG_SYS_TEXT_BASE
+#endif
+#endif
+
+/*
+ * USB configuration.  We enable MUSB support, both for host and for
+ * gadget.  We set USB0 as peripheral and USB1 as host, based on the
+ * board schematic and physical port wired to each.  Then for host we
+ * add mass storage support and for gadget we add both RNDIS ethernet
+ * and DFU.
+ */
+#define CONFIG_USB_MUSB_DSPS
+#define CONFIG_ARCH_MISC_INIT
+#define CONFIG_MUSB_GADGET
+#define CONFIG_MUSB_PIO_ONLY
+#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT
+#define CONFIG_USB_GADGET
+#define CONFIG_USBDOWNLOAD_GADGET
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_VBUS_DRAW    2
+#define CONFIG_MUSB_HOST
+#define CONFIG_AM335X_USB0
+#define CONFIG_AM335X_USB0_MODE        MUSB_PERIPHERAL
+#define CONFIG_AM335X_USB1
+#define CONFIG_AM335X_USB1_MODE MUSB_HOST
+
+#ifdef CONFIG_MUSB_HOST
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#endif
+
+#ifdef CONFIG_MUSB_GADGET
+#define CONFIG_USB_ETHER
+#define CONFIG_USB_ETH_RNDIS
+#define CONFIG_USBNET_HOST_ADDR        "de:ad:be:af:00:00"
+
+/* USB TI's IDs */
+#define CONFIG_G_DNL_VENDOR_NUM 0x0403
+#define CONFIG_G_DNL_PRODUCT_NUM 0xBD00
+#define CONFIG_G_DNL_MANUFACTURER "Texas Instruments"
+#endif /* CONFIG_MUSB_GADGET */
+
+#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_USBETH_SUPPORT)
+/* disable host part of MUSB in SPL */
+#undef CONFIG_MUSB_HOST
+/* disable EFI partitions and partition UUID support */
+#undef CONFIG_PARTITION_UUIDS
+#undef CONFIG_EFI_PARTITION
+/*
+ * Disable CPSW SPL support so we fit within the 101KiB limit.
+ */
+#undef CONFIG_SPL_ETH_SUPPORT
+#endif
+
+/* Network. */
+#define CONFIG_PHY_GIGE
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR                        0
+#define CONFIG_PHY_SMSC
+#define CONFIG_MII
+#define CONFIG_CMD_MII
+#define CONFIG_PHY_ATHEROS
+
+/* NAND support */
+#ifdef CONFIG_NAND
+#define CONFIG_CMD_NAND
+#define GPMC_NAND_ECC_LP_x8_LAYOUT     1
+#if !defined(CONFIG_SPI_BOOT) && !defined(CONFIG_NOR_BOOT)
+#define MTDIDS_DEFAULT                 "nand0=omap2-nand.0"
+#define MTDPARTS_DEFAULT               "mtdparts=omap2-nand.0:128k(SPL)," \
+                                       "128k(SPL.backup1)," \
+                                       "128k(SPL.backup2)," \
+                                       "128k(SPL.backup3)," \
+                                       "1920k(u-boot)," \
+                                       "-(UBI)"
+#define CONFIG_ENV_IS_NOWHERE
+#endif
+#endif
+
+#endif /* ! __CONFIG_BALTOS_H */