Create board support for GE PPD, based on mx53loco.
Use mx53ppd_defconfig make target to configure for this board.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
select BOARD_LATE_INIT
select MX53
+config TARGET_MX53PPD
+ bool "Support mx53ppd"
+ select MX53
+ help
+ Enable support for the GE Healthcare PPD.
+
config TARGET_MX53SMD
bool "Support mx53smd"
select MX53
source "board/freescale/mx53evk/Kconfig"
source "board/freescale/mx53loco/Kconfig"
source "board/freescale/mx53smd/Kconfig"
+source "board/ge/mx53ppd/Kconfig"
source "board/inversepath/usbarmory/Kconfig"
source "board/technologic/ts4800/Kconfig"
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0+
+
+if TARGET_MX53PPD
+
+config SYS_BOARD
+ default "mx53ppd"
+
+config SYS_VENDOR
+ default "ge"
+
+config SYS_SOC
+ default "mx5"
+
+config SYS_CONFIG_NAME
+ default "mx53ppd"
+
+endif
--- /dev/null
+MX53PPD BOARD
+M: Antti Mäentausta <antti.maentausta@ge.com>
+M: Martyn Welch <martyn.welch@collabora.co.uk>
+S: Maintained
+F: board/freescale/mx53ppd/
+F: include/configs/mx53ppd.h
+F: configs/mx53ppd_defconfig
--- /dev/null
+# Copyright 2017 General Electric Company
+#
+# Based on board/freescale/mx53loco/Makefile:
+#
+# (C) Copyright 2011 Freescale Semiconductor, Inc.
+# Jason Liu <r64343@freescale.com>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += mx53ppd.o
+obj-$(CONFIG_VIDEO) += mx53ppd_video.o
--- /dev/null
+/*
+ * Copyright 2017 General Electric Company
+ *
+ * Based on board/freescale/mx53loco/imximage.cfg:
+ *
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Jason Liu <r64343@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+/* image version */
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi, sd (the board has no nand neither onenand)
+ */
+BOOT_FROM sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+DATA 4 0x53fa8004 0x00194005
+DATA 4 0x53fa8554 0x00300000
+DATA 4 0x53fa8558 0x00300040
+DATA 4 0x53fa8560 0x00300000
+DATA 4 0x53fa8564 0x00300040
+DATA 4 0x53fa8568 0x00300040
+DATA 4 0x53fa8570 0x00300000
+DATA 4 0x53fa8574 0x00300000
+DATA 4 0x53fa8578 0x00300000
+DATA 4 0x53fa857c 0x00300040
+DATA 4 0x53fa8580 0x00300040
+DATA 4 0x53fa8584 0x00300000
+DATA 4 0x53fa8588 0x00300000
+DATA 4 0x53fa8590 0x00300040
+DATA 4 0x53fa8594 0x00300000
+DATA 4 0x53fa86f0 0x00300000
+DATA 4 0x53fa86f4 0x00000000
+DATA 4 0x53fa86fc 0x00000000
+DATA 4 0x53fa8714 0x00000000
+DATA 4 0x53fa8718 0x00300000
+DATA 4 0x53fa871c 0x00300000
+DATA 4 0x53fa8720 0x00300000
+DATA 4 0x53fa8728 0x00300000
+DATA 4 0x53fa872c 0x00300000
+DATA 4 0x63fd9088 0x35343535
+DATA 4 0x63fd9090 0x4d444c44
+DATA 4 0x63fd907c 0x01370138
+DATA 4 0x63fd9080 0x013b013c
+DATA 4 0x63fd9018 0x00111740
+DATA 4 0x63fd9000 0x85190000
+DATA 4 0x63fd900c 0x8b8f52e3
+DATA 4 0x63fd9010 0xb68e8a63
+DATA 4 0x63fd9014 0x01ff00db
+DATA 4 0x63fd902c 0x000026d2
+DATA 4 0x63fd9030 0x008f0e21
+DATA 4 0x63fd9008 0x09333030
+DATA 4 0x63fd9004 0x0002002d
+DATA 4 0x63fd901c 0x00008032
+DATA 4 0x63fd901c 0x00008033
+DATA 4 0x63fd901c 0x00468031
+DATA 4 0x63fd901c 0x052080b0
+DATA 4 0x63fd901c 0x04008040
+DATA 4 0x63fd901c 0x0000803a
+DATA 4 0x63fd901c 0x0000803b
+DATA 4 0x63fd901c 0x00028039
+DATA 4 0x63fd901c 0x05208138
+DATA 4 0x63fd901c 0x04008048
+DATA 4 0x63fd9020 0x00005800
+DATA 4 0x63fd9040 0x05380003
+DATA 4 0x63fd9058 0x00011110
+DATA 4 0x63fd901c 0x00000000
--- /dev/null
+/*
+ * Copyright 2017 General Electric Company
+ *
+ * Based on board/freescale/mx53loco/mx53loco.c:
+ *
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Jason Liu <r64343@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux-mx53.h>
+#include <asm/arch/clock.h>
+#include <linux/errno.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <asm/mach-imx/mx5_video.h>
+#include <netdev.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <asm/gpio.h>
+#include <power/pmic.h>
+#include <dialog_pmic.h>
+#include <fsl_pmic.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+#include <watchdog.h>
+#include "ppd_gpio.h"
+#include <stdlib.h>
+#include "../../ge/common/vpd_reader.h"
+#include <rtc.h>
+
+#define MX53PPD_LCD_POWER IMX_GPIO_NR(3, 24)
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Index of I2C1, SEGMENT 1 (see CONFIG_SYS_I2C_BUSES). */
+#define VPD_EEPROM_BUS 2
+
+/* Address of 24C08 EEPROM. */
+#define VPD_EEPROM_ADDR 0x50
+#define VPD_EEPROM_ADDR_LEN 1
+
+static u32 mx53_dram_size[2];
+
+phys_size_t get_effective_memsize(void)
+{
+ /*
+ * WARNING: We must override get_effective_memsize() function here
+ * to report only the size of the first DRAM bank. This is to make
+ * U-Boot relocator place U-Boot into valid memory, that is, at the
+ * end of the first DRAM bank. If we did not override this function
+ * like so, U-Boot would be placed at the address of the first DRAM
+ * bank + total DRAM size - sizeof(uboot), which in the setup where
+ * each DRAM bank contains 512MiB of DRAM would result in placing
+ * U-Boot into invalid memory area close to the end of the first
+ * DRAM bank.
+ */
+ return mx53_dram_size[0];
+}
+
+int dram_init(void)
+{
+ mx53_dram_size[0] = get_ram_size((void *)PHYS_SDRAM_1, 1 << 30);
+ mx53_dram_size[1] = get_ram_size((void *)PHYS_SDRAM_2, 1 << 30);
+
+ gd->ram_size = mx53_dram_size[0] + mx53_dram_size[1];
+
+ return 0;
+}
+
+int dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = mx53_dram_size[0];
+
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+ gd->bd->bi_dram[1].size = mx53_dram_size[1];
+
+ return 0;
+}
+
+u32 get_board_rev(void)
+{
+ return get_cpu_rev() & ~(0xF << 8);
+}
+
+#define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
+
+#ifdef CONFIG_USB_EHCI_MX5
+int board_ehci_hcd_init(int port)
+{
+ /* request VBUS power enable pin, GPIO7_8 */
+ imx_iomux_v3_setup_pad(MX53_PAD_PATA_DA_2__GPIO7_8);
+ gpio_direction_output(IMX_GPIO_NR(7, 8), 1);
+ return 0;
+}
+#endif
+
+static void setup_iomux_fec(void)
+{
+ static const iomux_v3_cfg_t fec_pads[] = {
+ NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__FEC_MDIO, PAD_CTL_HYS |
+ PAD_CTL_DSE_HIGH | PAD_CTL_PUS_22K_UP |
+ PAD_CTL_ODE),
+ NEW_PAD_CTRL(MX53_PAD_FEC_MDC__FEC_MDC, PAD_CTL_DSE_HIGH),
+ NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__FEC_RDATA_1,
+ PAD_CTL_HYS | PAD_CTL_PKE),
+ NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__FEC_RDATA_0,
+ PAD_CTL_HYS | PAD_CTL_PKE),
+ NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__FEC_TDATA_1, PAD_CTL_DSE_HIGH),
+ NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__FEC_TDATA_0, PAD_CTL_DSE_HIGH),
+ NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__FEC_TX_EN, PAD_CTL_DSE_HIGH),
+ NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__FEC_TX_CLK,
+ PAD_CTL_HYS | PAD_CTL_PKE),
+ NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__FEC_RX_ER,
+ PAD_CTL_HYS | PAD_CTL_PKE),
+ NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__FEC_RX_DV,
+ PAD_CTL_HYS | PAD_CTL_PKE),
+ };
+
+ imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
+}
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg esdhc_cfg[2] = {
+ {MMC_SDHC3_BASE_ADDR},
+ {MMC_SDHC1_BASE_ADDR},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ return 1;
+}
+
+#define SD_CMD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
+ PAD_CTL_PUS_100K_UP)
+#define SD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_DSE_HIGH)
+
+int board_mmc_init(bd_t *bis)
+{
+ static const iomux_v3_cfg_t sd1_pads[] = {
+ NEW_PAD_CTRL(MX53_PAD_PATA_RESET_B__ESDHC3_CMD,
+ SD_CMD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_IORDY__ESDHC3_CLK, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA8__ESDHC3_DAT0, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA9__ESDHC3_DAT1, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA10__ESDHC3_DAT2, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA11__ESDHC3_DAT3, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA0__ESDHC3_DAT4, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA1__ESDHC3_DAT5, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA2__ESDHC3_DAT6, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA3__ESDHC3_DAT7, SD_PAD_CTRL),
+ MX53_PAD_EIM_DA11__GPIO3_11,
+ };
+
+ static const iomux_v3_cfg_t sd2_pads[] = {
+ NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3, SD_PAD_CTRL),
+ MX53_PAD_EIM_DA13__GPIO3_13,
+ };
+
+ u32 index;
+ int ret;
+
+ esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+
+ for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) {
+ switch (index) {
+ case 0:
+ imx_iomux_v3_setup_multiple_pads(sd1_pads,
+ ARRAY_SIZE(sd1_pads));
+ break;
+ case 1:
+ imx_iomux_v3_setup_multiple_pads(sd2_pads,
+ ARRAY_SIZE(sd2_pads));
+ break;
+ default:
+ printf("Warning: you configured more ESDHC controller (%d) as supported by the board(2)\n",
+ CONFIG_SYS_FSL_ESDHC_NUM);
+ return -EINVAL;
+ }
+ ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+#endif
+
+#define I2C_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
+
+static void setup_iomux_i2c(void)
+{
+ static const iomux_v3_cfg_t i2c1_pads[] = {
+ NEW_PAD_CTRL(MX53_PAD_CSI0_DAT8__I2C1_SDA, I2C_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_CSI0_DAT9__I2C1_SCL, I2C_PAD_CTRL),
+ };
+
+ imx_iomux_v3_setup_multiple_pads(i2c1_pads, ARRAY_SIZE(i2c1_pads));
+}
+
+#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+static struct i2c_pads_info i2c_pad_info1 = {
+ .scl = {
+ .i2c_mode = MX53_PAD_EIM_D21__I2C1_SCL | I2C_PAD,
+ .gpio_mode = MX53_PAD_EIM_D28__GPIO3_28 | I2C_PAD,
+ .gp = IMX_GPIO_NR(3, 28)
+ },
+ .sda = {
+ .i2c_mode = MX53_PAD_EIM_D28__I2C1_SDA | I2C_PAD,
+ .gpio_mode = MX53_PAD_EIM_D21__GPIO3_21 | I2C_PAD,
+ .gp = IMX_GPIO_NR(3, 21)
+ }
+};
+
+static int clock_1GHz(void)
+{
+ int ret;
+ u32 ref_clk = MXC_HCLK;
+ /*
+ * After increasing voltage to 1.25V, we can switch
+ * CPU clock to 1GHz and DDR to 400MHz safely
+ */
+ ret = mxc_set_clock(ref_clk, 1000, MXC_ARM_CLK);
+ if (ret) {
+ printf("CPU: Switch CPU clock to 1GHZ failed\n");
+ return -1;
+ }
+
+ ret = mxc_set_clock(ref_clk, 400, MXC_PERIPH_CLK);
+ ret |= mxc_set_clock(ref_clk, 400, MXC_DDR_CLK);
+ if (ret) {
+ printf("CPU: Switch DDR clock to 400MHz failed\n");
+ return -1;
+ }
+
+ return 0;
+}
+
+void ppd_gpio_init(void)
+{
+ int i;
+
+ imx_iomux_v3_setup_multiple_pads(ppd_pads, ARRAY_SIZE(ppd_pads));
+ for (i = 0; i < ARRAY_SIZE(ppd_gpios); ++i)
+ gpio_direction_output(ppd_gpios[i].gpio, ppd_gpios[i].value);
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_fec();
+ setup_iomux_lcd();
+ ppd_gpio_init();
+
+ return 0;
+}
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+ return 1;
+}
+
+#define VPD_TYPE_INVALID 0x00
+#define VPD_BLOCK_NETWORK 0x20
+#define VPD_BLOCK_HWID 0x44
+#define VPD_PRODUCT_PPD 4
+#define VPD_HAS_MAC1 0x1
+#define VPD_MAC_ADDRESS_LENGTH 6
+
+struct vpd_cache {
+ u8 product_id;
+ u8 has;
+ unsigned char mac1[VPD_MAC_ADDRESS_LENGTH];
+};
+
+/*
+ * Extracts MAC and product information from the VPD.
+ */
+static int vpd_callback(void *userdata, u8 id, u8 version, u8 type, size_t size,
+ u8 const *data)
+{
+ struct vpd_cache *vpd = (struct vpd_cache *)userdata;
+
+ if (id == VPD_BLOCK_HWID && version == 1 && type != VPD_TYPE_INVALID &&
+ size >= 1) {
+ vpd->product_id = data[0];
+
+ } else if (id == VPD_BLOCK_NETWORK && version == 1 &&
+ type != VPD_TYPE_INVALID) {
+ if (size >= 6) {
+ vpd->has |= VPD_HAS_MAC1;
+ memcpy(vpd->mac1, data, VPD_MAC_ADDRESS_LENGTH);
+ }
+ }
+
+ return 0;
+}
+
+static void process_vpd(struct vpd_cache *vpd)
+{
+ int fec_index = -1;
+
+ if (vpd->product_id == VPD_PRODUCT_PPD)
+ fec_index = 0;
+
+ if (fec_index >= 0 && (vpd->has & VPD_HAS_MAC1))
+ eth_env_set_enetaddr("ethaddr", vpd->mac1);
+}
+
+static int read_vpd(uint eeprom_bus)
+{
+ struct vpd_cache vpd;
+ int res;
+ int size = 1024;
+ u8 *data;
+ unsigned int current_i2c_bus = i2c_get_bus_num();
+
+ res = i2c_set_bus_num(eeprom_bus);
+ if (res < 0)
+ return res;
+
+ data = malloc(size);
+ if (!data)
+ return -ENOMEM;
+
+ res = i2c_read(VPD_EEPROM_ADDR, 0, VPD_EEPROM_ADDR_LEN, data, size);
+ if (res == 0) {
+ memset(&vpd, 0, sizeof(vpd));
+ vpd_reader(size, data, &vpd, vpd_callback);
+ process_vpd(&vpd);
+ }
+
+ free(data);
+
+ i2c_set_bus_num(current_i2c_bus);
+ return res;
+}
+
+static void check_time(void)
+{
+ int ret, i;
+ struct rtc_time tm;
+ u8 retry = 3;
+
+ unsigned int current_i2c_bus = i2c_get_bus_num();
+
+ ret = i2c_set_bus_num(CONFIG_SYS_RTC_BUS_NUM);
+ if (ret < 0)
+ return;
+
+ rtc_init();
+
+ for (i = 0; i < retry; i++) {
+ ret = rtc_get(&tm);
+ if (!ret || ret == -EINVAL)
+ break;
+ }
+
+ if (ret < 0)
+ env_set("rtc_status", "RTC_ERROR");
+
+ if (tm.tm_year > 2037) {
+ tm.tm_sec = 0;
+ tm.tm_min = 0;
+ tm.tm_hour = 0;
+ tm.tm_mday = 1;
+ tm.tm_wday = 2;
+ tm.tm_mon = 1;
+ tm.tm_year = 2036;
+
+ for (i = 0; i < retry; i++) {
+ ret = rtc_set(&tm);
+ if (!ret)
+ break;
+ }
+
+ if (ret < 0)
+ env_set("rtc_status", "RTC_ERROR");
+ }
+
+ i2c_set_bus_num(current_i2c_bus);
+}
+
+int board_init(void)
+{
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+ mxc_set_sata_internal_clock();
+ setup_iomux_i2c();
+
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ const char *cause;
+
+ /* We care about WDOG only, treating everything else as
+ * a power-on-reset.
+ */
+ if (get_imx_reset_cause() & 0x0010)
+ cause = "WDOG";
+ else
+ cause = "POR";
+
+ env_set("bootcause", cause);
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ int res;
+
+ read_vpd(VPD_EEPROM_BUS);
+
+ res = clock_1GHz();
+ if (res != 0)
+ return res;
+
+ print_cpuinfo();
+ hw_watchdog_init();
+
+ check_time();
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: GE PPD\n");
+
+ return 0;
+}
--- /dev/null
+/*
+ * Copyright 2017 General Electric Company
+ *
+ * Based on board/freescale/mx53loco/mx53loco_video.c:
+ *
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ * Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <linux/list.h>
+#include <asm/gpio.h>
+#include <asm/arch/iomux-mx53.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/io.h>
+#include <pwm.h>
+#include "ppd_gpio.h"
+
+#define MX53PPD_LCD_POWER IMX_GPIO_NR(3, 24)
+
+static struct fb_videomode const nv_spwg = {
+ .name = "NV-SPWGRGB888",
+ .refresh = 60,
+ .xres = 800,
+ .yres = 480,
+ .pixclock = 15384,
+ .left_margin = 16,
+ .right_margin = 210,
+ .upper_margin = 10,
+ .lower_margin = 22,
+ .hsync_len = 30,
+ .vsync_len = 13,
+ .sync = FB_SYNC_EXT,
+ .vmode = FB_VMODE_NONINTERLACED
+};
+
+void setup_iomux_lcd(void)
+{
+ static const iomux_v3_cfg_t lcd_pads[] = {
+ MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK,
+ MX53_PAD_DI0_PIN15__IPU_DI0_PIN15,
+ MX53_PAD_DI0_PIN2__IPU_DI0_PIN2,
+ MX53_PAD_DI0_PIN3__IPU_DI0_PIN3,
+ MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0,
+ MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1,
+ MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2,
+ MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3,
+ MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4,
+ MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5,
+ MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6,
+ MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7,
+ MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8,
+ MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9,
+ MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10,
+ MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11,
+ MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12,
+ MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13,
+ MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14,
+ MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15,
+ MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16,
+ MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17,
+ MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18,
+ MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19,
+ MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20,
+ MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21,
+ MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22,
+ MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23,
+ };
+
+ imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
+}
+
+static void lcd_enable(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ /* Set LDB_DI0 as clock source for IPU_DI0 */
+ clrsetbits_le32(&mxc_ccm->cscmr2,
+ MXC_CCM_CSCMR2_DI0_CLK_SEL_MASK,
+ MXC_CCM_CSCMR2_DI0_CLK_SEL(
+ MXC_CCM_CSCMR2_DI0_CLK_SEL_LDB_DI0_CLK));
+
+ /* Turn on IPU LDB DI0 clocks */
+ setbits_le32(&mxc_ccm->CCGR6, MXC_CCM_CCGR6_LDB_DI0(3));
+
+ /* Turn on IPU DI0 clocks */
+ setbits_le32(&mxc_ccm->CCGR6, MXC_CCM_CCGR6_IPU_DI0(3));
+
+ /* Configure LDB */
+ writel(IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
+ IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
+ IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0,
+ &iomux->gpr[2]);
+
+ /* Enable backlights */
+ pwm_init(1, 0, 0);
+
+ /* duty cycle 5000000ns, period: 5000000ns */
+ pwm_config(1, 5000000, 5000000);
+
+ /* Backlight Power */
+ gpio_direction_output(BACKLIGHT_ENABLE, 1);
+
+ pwm_enable(1);
+}
+
+static int do_lcd_enable(cmd_tbl_t *cmdtp, int flag, int argc,
+ char * const argv[])
+{
+ lcd_enable();
+ return 0;
+}
+
+U_BOOT_CMD(
+ ppd_lcd_enable, 1, 1, do_lcd_enable,
+ "enable PPD LCD",
+ "no parameters"
+);
+
+int board_video_skip(void)
+{
+ int ret;
+
+ ret = ipuv3_fb_init(&nv_spwg, 0, IPU_PIX_FMT_RGB24);
+ if (ret)
+ printf("Display cannot be configured: %d\n", ret);
+
+ return ret;
+}
--- /dev/null
+/*
+ * (C) Copyright 2015 General Electric Company
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __PPD_GPIO_H_
+#define __PPD_GPIO_H_
+
+#include <asm/arch/iomux-mx53.h>
+#include <asm/gpio.h>
+
+#define PPD_UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
+ PAD_CTL_PUS_100K_UP)
+
+static const iomux_v3_cfg_t ppd_pads[] = {
+ /* FEC */
+ MX53_PAD_EIM_A22__GPIO2_16,
+ /* UART */
+ NEW_PAD_CTRL(MX53_PAD_PATA_DMACK__UART1_RXD_MUX, PPD_UART_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DIOW__UART1_TXD_MUX, PPD_UART_PAD_CTRL),
+ /* Video */
+ MX53_PAD_CSI0_DATA_EN__GPIO5_20, /* LR_SCAN_CTRL */
+ MX53_PAD_CSI0_VSYNC__GPIO5_21, /* UD_SCAN_CTRL */
+ MX53_PAD_CSI0_DAT10__GPIO5_28, /* DATA_WIDTH_CTRL */
+ MX53_PAD_CSI0_PIXCLK__GPIO5_18, /* HOST_CONTROLLED_RESET_TO_LCD_N */
+ MX53_PAD_EIM_DA2__GPIO3_2, /* LVDS1_MUX_CTRL */
+ MX53_PAD_EIM_DA3__GPIO3_3, /* LVDS0_MUX_CTRL */
+ MX53_PAD_EIM_A21__GPIO2_17, /* ENABLE_PWR_TO_LCD_AND_UI_INTERFACE */
+ MX53_PAD_CSI0_DAT11__GPIO5_29, /* BACKLIGHT_ENABLE */
+ MX53_PAD_DISP0_DAT9__PWM2_PWMO, /* IMX535_PWM2_TO_LCD_CONNECTOR */
+ /* I2C */
+ MX53_PAD_EIM_A20__GPIO2_18, /* RESET_I2C1_BUS_SEGMENT_MUX_N */
+
+ /* SPI */
+ MX53_PAD_DISP0_DAT23__GPIO5_17,
+ MX53_PAD_KEY_COL2__GPIO4_10,
+ MX53_PAD_KEY_ROW2__GPIO4_11,
+ MX53_PAD_KEY_COL3__GPIO4_12,
+};
+
+struct gpio_cfg {
+ unsigned int gpio;
+ int value;
+};
+
+#define RESET_IMX535_ETHERNET_PHY_N IMX_GPIO_NR(2, 16)
+#define UD_SCAN_CTRL IMX_GPIO_NR(5, 21)
+#define LR_SCAN_CTRL IMX_GPIO_NR(5, 20)
+#define LVDS0_MUX_CTRL IMX_GPIO_NR(3, 3)
+#define LVDS1_MUX_CTRL IMX_GPIO_NR(3, 2)
+#define HOST_CONTROLLED_RESET_TO_LCD_N IMX_GPIO_NR(5, 18)
+#define DATA_WIDTH_CTRL IMX_GPIO_NR(5, 28)
+#define RESET_DP0_TRANSMITTER_N IMX_GPIO_NR(2, 28)
+#define RESET_DP1_TRANSMITTER_N IMX_GPIO_NR(2, 29)
+#define POWER_DOWN_LVDS0_DESERIALIZER_N IMX_GPIO_NR(2, 22)
+#define POWER_DOWN_LVDS1_DESERIALIZER_N IMX_GPIO_NR(2, 27)
+#define ENABLE_PWR_TO_LCD_AND_UI_INTERFACE IMX_GPIO_NR(2, 17)
+#define BACKLIGHT_ENABLE IMX_GPIO_NR(5, 29)
+#define RESET_I2C1_BUS_SEGMENT_MUX_N IMX_GPIO_NR(2, 18)
+#define ECSPI1_CS0 IMX_GPIO_NR(5, 17)
+#define ECSPI1_CS1 IMX_GPIO_NR(4, 10)
+#define ECSPI1_CS2 IMX_GPIO_NR(4, 11)
+#define ECSPI1_CS3 IMX_GPIO_NR(4, 12)
+
+static const struct gpio_cfg ppd_gpios[] = {
+ /* FEC */
+ /* Drive Low as GPIO output for 25ms per Eth Phy IX spec */
+ /* Then Drive High as GPIO output to bring Eth Phy IC out of reset */
+ { RESET_IMX535_ETHERNET_PHY_N, 0 },
+ { RESET_IMX535_ETHERNET_PHY_N, 1 },
+ /* Video */
+ { UD_SCAN_CTRL, 0 },
+ { LR_SCAN_CTRL, 1 },
+#ifdef PROPRIETARY_CHANGES
+ { LVDS0_MUX_CTRL, 1 },
+#else
+ { LVDS0_MUX_CTRL, 0 },
+#endif
+ { LVDS1_MUX_CTRL, 1 },
+ { HOST_CONTROLLED_RESET_TO_LCD_N, 1 },
+ { DATA_WIDTH_CTRL, 0 },
+ { RESET_DP0_TRANSMITTER_N, 1 },
+ { RESET_DP1_TRANSMITTER_N, 1 },
+ { POWER_DOWN_LVDS0_DESERIALIZER_N, 1 },
+ { POWER_DOWN_LVDS1_DESERIALIZER_N, 1 },
+ { ENABLE_PWR_TO_LCD_AND_UI_INTERFACE, 1 },
+ { BACKLIGHT_ENABLE, 0 },
+ { RESET_I2C1_BUS_SEGMENT_MUX_N, 1 },
+ { ECSPI1_CS0, 1 },
+ { ECSPI1_CS1, 1 },
+ { ECSPI1_CS2, 1 },
+ { ECSPI1_CS3, 1 },
+};
+
+#endif /* __PPD_GPIO_H_ */
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MX5=y
+CONFIG_TARGET_MX53PPD=y
+CONFIG_FIT=y
+CONFIG_BOOTCOUNT=y
+CONFIG_BOOTCOUNT_EXT=y
+CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE="mmc"
+CONFIG_SYS_BOOTCOUNT_EXT_DEVPART="0:5"
+CONFIG_SYS_BOOTCOUNT_EXT_NAME="/boot/failures"
+CONFIG_SYS_BOOTCOUNT_ADDR=0x7000A000
+CONFIG_NETDEVICES=y
+CONFIG_VIDEO=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/ge/mx53ppd/imximage.cfg"
+CONFIG_BOOTDELAY=1
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
+CONFIG_DISPLAY_CPUINFO=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_I2C=y
+CONFIG_RTC_S35392A=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_USB=y
+CONFIG_USB_STORAGE=y
+# CONFIG_VIDEO_SW_CURSOR is not set
+CONFIG_OF_LIBFDT=y
+
+CONFIG_MMC=y
--- /dev/null
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Jason Liu <r64343@freescale.com>
+ *
+ * Configuration settings for Freescale MX53 low cost board.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+
+#define CONSOLE_DEV "ttymxc0"
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+#define CONFIG_SYS_FSL_CLK
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
+
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_IMX_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT_MSECS 8000
+
+#define CONFIG_MISC_INIT_R
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_MXC_GPIO
+#define CONFIG_REVISION_TAG
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+#define CONFIG_SYS_FSL_ESDHC_NUM 2
+
+#define CONFIG_SUPPORT_RAW_INITRD /* bootz raw initrd support */
+
+/* Eth Configs */
+#define CONFIG_MII
+
+#define CONFIG_FEC_MXC
+#define IMX_FEC_BASE FEC_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR 0x1F
+
+/* USB Configs */
+#define CONFIG_USB_EHCI_MX5
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_ETHER_MCS7830
+#define CONFIG_USB_ETHER_SMSC95XX
+#define CONFIG_MXC_USB_PORT 1
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+
+#define CONFIG_SYS_RTC_BUS_NUM 2
+#define CONFIG_SYS_I2C_RTC_ADDR 0x30
+
+/* I2C Configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
+
+/* PMIC Controller */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_DIALOG_POWER
+#define CONFIG_POWER_FSL
+#define CONFIG_POWER_FSL_MC13892
+#define CONFIG_SYS_DIALOG_PMIC_I2C_ADDR 0x48
+#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+
+/* Command definition */
+#define CONFIG_SUPPORT_RAW_INITRD
+
+#define CONFIG_ETHPRIME "FEC0"
+
+#define CONFIG_LOADADDR 0x72000000 /* loadaddr env var */
+#define CONFIG_SYS_TEXT_BASE 0x77800000
+
+#define PPD_CONFIG_NFS \
+ "nfsserver=192.168.252.95\0" \
+ "gatewayip=192.168.252.95\0" \
+ "netmask=255.255.255.0\0" \
+ "ipaddr=192.168.252.99\0" \
+ "kernsize=0x2000\0" \
+ "use_dhcp=0\0" \
+ "nfsroot=/opt/springdale/rd\0" \
+ "bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs " \
+ "${kern_ipconf} nfsroot=${nfsserver}:${nfsroot},v3,tcp rw\0" \
+ "choose_ip=if test $use_dhcp = 1; then set kern_ipconf ip=dhcp; " \
+ "set getcmd dhcp; else set kern_ipconf " \
+ "ip=${ipaddr}:${nfsserver}:${gatewayip}:${netmask}::eth0:off; " \
+ "set getcmd tftp; fi\0" \
+ "nfs=run choose_ip setargs bootargs_nfs; ${getcmd} ${loadaddr} " \
+ "${nfsserver}:${image}; bootm ${loadaddr}\0" \
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ PPD_CONFIG_NFS \
+ "bootlimit=10\0" \
+ "image=/boot/fitImage\0" \
+ "fdt_high=0xffffffff\0" \
+ "dev=mmc\0" \
+ "devnum=0\0" \
+ "rootdev=mmcblk0p\0" \
+ "quiet=quiet loglevel=0\0" \
+ "console=" CONSOLE_DEV "\0" \
+ "lvds=ldb\0" \
+ "setargs=setenv bootargs ${lvds} jtag=on mem=2G " \
+ "vt.global_cursor_default=0 bootcause=${bootcause} ${quiet} " \
+ "console=${console} ${rtc_status}\0" \
+ "bootargs_emmc=setenv bootargs root=/dev/${rootdev}${partnum} ro " \
+ "rootwait ${bootargs}\0" \
+ "doquiet=if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \
+ "then setenv quiet; fi\0" \
+ "hasfirstboot=ext2load ${dev} ${devnum}:${partnum} 0x7000A000 " \
+ "/boot/bootcause/firstboot\0" \
+ "swappartitions=setexpr partnum 3 - ${partnum}\0" \
+ "failbootcmd=" \
+ "ppd_lcd_enable; " \
+ "msg=\"Monitor failed to start. " \
+ "Try again, or contact GE Service for support.\"; " \
+ "echo $msg; " \
+ "setenv stdout vga; " \
+ "echo \"\n\n\n\n \" $msg; " \
+ "setenv stdout serial; " \
+ "mw.b 0x7000A000 0xbc; " \
+ "mw.b 0x7000A001 0x00; " \
+ "ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \
+ "altbootcmd=" \
+ "run doquiet; " \
+ "setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
+ "run hasfirstboot || setenv partnum 0; " \
+ "if test ${partnum} != 0; then " \
+ "setenv bootcause REVERT; " \
+ "run swappartitions loadimage doboot; " \
+ "fi; " \
+ "run failbootcmd\0" \
+ "loadimage=" \
+ "ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
+ "doboot=" \
+ "echo Booting from ${dev}:${devnum}:${partnum} ...; " \
+ "run setargs; " \
+ "run bootargs_emmc; " \
+ "bootm ${loadaddr}\0" \
+ "tryboot=" \
+ "setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
+ "run loadimage || run swappartitions && run loadimage || " \
+ "setenv partnum 0 && echo MISSING IMAGE;" \
+ "run doboot; " \
+ "run failbootcmd\0" \
+ "video-mode=" \
+ "lcd:800x480-24@60,monitor=lcd\0" \
+
+#define CONFIG_MMCBOOTCOMMAND \
+ "if mmc dev ${devnum}; then " \
+ "run doquiet; " \
+ "run tryboot; " \
+ "fi; " \
+
+#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
+
+#define CONFIG_ARP_TIMEOUT 200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+
+#define CONFIG_SYS_MAXARGS 48 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x70000000
+#define CONFIG_SYS_MEMTEST_END 0x70010000
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 2
+#define PHYS_SDRAM_1 CSD0_BASE_ADDR
+#define PHYS_SDRAM_1_SIZE (gd->bd->bi_dram[0].size)
+#define PHYS_SDRAM_2 CSD1_BASE_ADDR
+#define PHYS_SDRAM_2_SIZE (gd->bd->bi_dram[1].size)
+#define PHYS_SDRAM_SIZE (gd->ram_size)
+
+#define CONFIG_SYS_SDRAM_BASE (PHYS_SDRAM_1)
+#define CONFIG_SYS_INIT_RAM_ADDR (IRAM_BASE_ADDR)
+#define CONFIG_SYS_INIT_RAM_SIZE (IRAM_SIZE)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
+#define CONFIG_ENV_SIZE (8 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#define CONFIG_CMD_FUSE
+#define CONFIG_FSL_IIM
+
+#define CONFIG_SYS_I2C_SPEED 100000
+
+/* I2C1 */
+#define CONFIG_SYS_NUM_I2C_BUSES 9
+#define CONFIG_SYS_I2C_MAX_HOPS 1
+#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \
+ }
+
+#define CONFIG_BCH
+
+#define CONFIG_BOOTCOUNT_LIMIT
+
+/* Backlight Control */
+#define CONFIG_PWM_IMX
+#define CONFIG_IMX6_PWM_PER_CLK 66666000
+
+/* Framebuffer and LCD */
+#ifdef CONFIG_VIDEO
+ #define CONFIG_VIDEO_IPUV3
+#endif
+
+#endif /* __CONFIG_H */
projects / oweals / u-boot.git / commitdiff