--- /dev/null
+/*
+ * Copyright (C) 2015 Altera Corporation
+ *
+ * This file is generated by sopc2dts.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/dts-v1/;
+
+/ {
+ model = "Altera NiosII Max10";
+ compatible = "altr,niosii-max10";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu: cpu@0 {
+ device_type = "cpu";
+ compatible = "altr,nios2-1.1";
+ reg = <0x00000000>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ altr,exception-addr = <0xc8000120>;
+ altr,fast-tlb-miss-addr = <0xc0000100>;
+ altr,has-div = <1>;
+ altr,has-initda = <1>;
+ altr,has-mmu = <1>;
+ altr,has-mul = <1>;
+ altr,implementation = "fast";
+ altr,pid-num-bits = <8>;
+ altr,reset-addr = <0xd4000000>;
+ altr,tlb-num-entries = <256>;
+ altr,tlb-num-ways = <16>;
+ altr,tlb-ptr-sz = <8>;
+ clock-frequency = <75000000>;
+ dcache-line-size = <32>;
+ dcache-size = <32768>;
+ icache-line-size = <32>;
+ icache-size = <32768>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x08000000 0x08000000>,
+ <0x00000000 0x00000400>;
+ };
+
+ sopc0: sopc@0 {
+ device_type = "soc";
+ ranges;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "altr,avalon", "simple-bus";
+ bus-frequency = <75000000>;
+
+ jtag_uart: serial@18001530 {
+ compatible = "altr,juart-1.0";
+ reg = <0x18001530 0x00000008>;
+ interrupt-parent = <&cpu>;
+ interrupts = <7>;
+ };
+
+ a_16550_uart_0: serial@18001600 {
+ compatible = "altr,16550-FIFO32", "ns16550a";
+ reg = <0x18001600 0x00000200>;
+ interrupt-parent = <&cpu>;
+ interrupts = <1>;
+ auto-flow-control = <1>;
+ clock-frequency = <50000000>;
+ fifo-size = <32>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ };
+
+ ext_flash: quadspi@0x180014a0 {
+ compatible = "altr,quadspi-1.0";
+ reg = <0x180014a0 0x00000020>,
+ <0x14000000 0x04000000>;
+ reg-names = "avl_csr", "avl_mem";
+ interrupt-parent = <&cpu>;
+ interrupts = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ flash0: nor0@0 {
+ compatible = "micron,n25q512a";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+ };
+
+ sysid: sysid@18001528 {
+ compatible = "altr,sysid-1.0";
+ reg = <0x18001528 0x00000008>;
+ };
+
+ rgmii_0_eth_tse_0: ethernet@400 {
+ compatible = "altr,tse-msgdma-1.0", "altr,tse-1.0";
+ reg = <0x00000400 0x00000400>,
+ <0x00000820 0x00000020>,
+ <0x00000800 0x00000020>,
+ <0x000008c0 0x00000008>,
+ <0x00000840 0x00000020>,
+ <0x00000860 0x00000020>;
+ reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp",
+ "tx_csr", "tx_desc";
+ interrupt-parent = <&cpu>;
+ interrupts = <2 3>;
+ interrupt-names = "rx_irq", "tx_irq";
+ rx-fifo-depth = <8192>;
+ tx-fifo-depth = <8192>;
+ address-bits = <48>;
+ max-frame-size = <1518>;
+ local-mac-address = [00 00 00 00 00 00];
+ altr,has-supplementary-unicast;
+ altr,enable-sup-addr = <1>;
+ altr,has-hash-multicast-filter;
+ altr,enable-hash = <1>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&phy0>;
+ rgmii_0_eth_tse_0_mdio: mdio {
+ compatible = "altr,tse-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+ };
+ };
+
+ enet_pll: clock@0 {
+ compatible = "altr,pll-1.0";
+ #clock-cells = <1>;
+
+ enet_pll_c0: enet_pll_c0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ clock-output-names = "enet_pll-c0";
+ };
+
+ enet_pll_c1: enet_pll_c1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ clock-output-names = "enet_pll-c1";
+ };
+
+ enet_pll_c2: enet_pll_c2 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <2500000>;
+ clock-output-names = "enet_pll-c2";
+ };
+ };
+
+ sys_pll: clock@1 {
+ compatible = "altr,pll-1.0";
+ #clock-cells = <1>;
+
+ sys_pll_c0: sys_pll_c0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-output-names = "sys_pll-c0";
+ };
+
+ sys_pll_c1: sys_pll_c1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ clock-output-names = "sys_pll-c1";
+ };
+
+ sys_pll_c2: sys_pll_c2 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <75000000>;
+ clock-output-names = "sys_pll-c2";
+ };
+ };
+
+ sys_clk_timer: timer@18001440 {
+ compatible = "altr,timer-1.0";
+ reg = <0x18001440 0x00000020>;
+ interrupt-parent = <&cpu>;
+ interrupts = <0>;
+ clock-frequency = <75000000>;
+ };
+
+ led_pio: gpio@180014d0 {
+ compatible = "altr,pio-1.0";
+ reg = <0x180014d0 0x00000010>;
+ altr,gpio-bank-width = <4>;
+ resetvalue = <15>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-bank-name = "led";
+ };
+
+ uart_0: serial@0x18001420 {
+ compatible = "altr,uart-1.0";
+ reg = <0x18001420 0x00000020>;
+ interrupt-parent = <&cpu>;
+ interrupts = <1>;
+ clock-frequency = <75000000>;
+ current-speed = <115200>;
+ };
+
+ button_pio: gpio@180014c0 {
+ compatible = "altr,pio-1.0";
+ reg = <0x180014c0 0x00000010>;
+ interrupt-parent = <&cpu>;
+ interrupts = <6>;
+ altr,gpio-bank-width = <3>;
+ altr,interrupt-type = <2>;
+ edge_type = <1>;
+ level_trigger = <0>;
+ resetvalue = <0>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-bank-name = "button";
+ };
+
+ sys_clk_timer_1: timer@880 {
+ compatible = "altr,timer-1.0";
+ reg = <0x00000880 0x00000020>;
+ interrupt-parent = <&cpu>;
+ interrupts = <5>;
+ clock-frequency = <75000000>;
+ };
+
+ fpga_leds: leds {
+ compatible = "gpio-leds";
+
+ led_fpga0: fpga0 {
+ label = "fpga_led0";
+ gpios = <&led_pio 0 1>;
+ };
+
+ led_fpga1: fpga1 {
+ label = "fpga_led1";
+ gpios = <&led_pio 1 1>;
+ };
+
+ led_fpga2: fpga2 {
+ label = "fpga_led2";
+ gpios = <&led_pio 2 1>;
+ };
+
+ led_fpga3: fpga3 {
+ label = "fpga_led3";
+ gpios = <&led_pio 3 1>;
+ };
+ };
+ };
+
+ chosen {
+ bootargs = "debug console=ttyS0,115200";
+ stdout-path = &uart_0;
+ };
+};
--- /dev/null
+/*
+ * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ * (C) Copyright 2010, Thomas Chou <thomas@wytron.com.tw>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * BOARD/CPU
+ */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+/*
+ * SERIAL
+ */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_CONSOLE_INFO_QUIET /* Suppress console info */
+
+/*
+ * Flash
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 1024
+#define CONFIG_MTD_DEVICE
+
+/*
+ * NET options
+ */
+#define CONFIG_SYS_RX_ETH_BUFFER 0
+#define CONFIG_CMD_MII
+#define CONFIG_PHY_GIGE
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+#define CONFIG_PHY_MARVELL
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * FDT options
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_LMB
+
+/*
+ * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
+ * CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the
+ * reset address, no? This will keep the environment in user region
+ * of flash. NOTE: the monitor length must be multiple of sector size
+ * (which is common practice).
+ */
+#define CONFIG_ENV_IS_IN_FLASH
+
+#define CONFIG_ENV_SIZE 0x10000 /* 64k, 1 sector */
+#define CONFIG_ENV_OVERWRITE /* Serial change Ok */
+#define CONFIG_ENV_ADDR 0xf4040000
+
+/*
+ * MEMORY ORGANIZATION
+ * -Monitor at top of sdram.
+ * -The heap is placed below the monitor
+ * -The stack is placed below the heap (&grows down).
+ */
+#define CONFIG_SYS_SDRAM_BASE 0xc8000000
+#define CONFIG_SYS_SDRAM_SIZE 0x08000000
+#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_MONITOR_IS_IN_RAM
+#define CONFIG_SYS_MONITOR_LEN 0x40000 /* Reserve 256k */
+#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_SDRAM_BASE + \
+ CONFIG_SYS_SDRAM_SIZE - \
+ CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_SYS_MALLOC_LEN 0x20000
+
+/*
+ * MISC
+ */
+#define CONFIG_SYS_LONGHELP /* Provide extended help */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */
+#define CONFIG_SYS_MAXARGS 16 /* Max command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Bootarg buf size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + \
+ 16) /* Print buf size */
+#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MONITOR_BASE - \
+ CONFIG_ENV_SIZE - \
+ CONFIG_SYS_MALLOC_LEN - \
+ 0x10000)
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_CMD_GPIO
+
+#endif /* __CONFIG_H */
projects / oweals / u-boot.git / commitdiff