--- /dev/null
+#
+# Copyright (C) 2006 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+include $(TOPDIR)/rules.mk
+
+ARCH:=mips
+BOARD:=easygate
+BOARDNAME:=9Cegetel Easygate
+FEATURES:=squashfs jffs2 usb atm
+
+define Target/Description
+ Build firmware images for 9Cegetel EasyGate
+endef
+
+include $(INCLUDE_DIR)/kernel-build.mk
+
+# include the profiles
+-include profiles/*.mk
+
+$(eval $(call BuildKernel))
--- /dev/null
+CONFIG_32BIT=y
+# CONFIG_64BIT is not set
+# CONFIG_64BIT_PHYS_ADDR is not set
+# CONFIG_8139TOO is not set
+CONFIG_AUDIT=y
+CONFIG_AUDIT_GENERIC=y
+# CONFIG_B44 is not set
+CONFIG_BASE_SMALL=0
+CONFIG_BCM963XX=y
+CONFIG_BINFMT_MISC=m
+# CONFIG_BLK_DEV_INITRD is not set
+CONFIG_BLK_DEV_IO_TRACE=y
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BSD_DISKLABEL is not set
+CONFIG_BSD_PROCESS_ACCT_V3=y
+# CONFIG_BT_CMTP is not set
+CONFIG_CFE=y
+CONFIG_CICADA_PHY=m
+# CONFIG_CIFS is not set
+# CONFIG_CLS_U32_MARK is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_CPU_BIG_ENDIAN=y
+CONFIG_CPU_HAS_LLSC=y
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_CPU_HAS_SYNC=y
+# CONFIG_CPU_LITTLE_ENDIAN is not set
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPS32_R1=y
+# CONFIG_CPU_MIPS32_R2 is not set
+# CONFIG_CPU_MIPS64_R1 is not set
+# CONFIG_CPU_MIPS64_R2 is not set
+CONFIG_CPU_MIPSR1=y
+# CONFIG_CPU_NEVADA is not set
+# CONFIG_CPU_R10000 is not set
+# CONFIG_CPU_R3000 is not set
+# CONFIG_CPU_R4300 is not set
+# CONFIG_CPU_R4X00 is not set
+# CONFIG_CPU_R5000 is not set
+# CONFIG_CPU_R5432 is not set
+# CONFIG_CPU_R6000 is not set
+# CONFIG_CPU_R8000 is not set
+# CONFIG_CPU_RM7000 is not set
+# CONFIG_CPU_RM9000 is not set
+# CONFIG_CPU_SB1 is not set
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+# CONFIG_CPU_TX39XX is not set
+# CONFIG_CPU_TX49XX is not set
+# CONFIG_CPU_VR41XX is not set
+CONFIG_CRAMFS=y
+CONFIG_CRYPTO_AES=y
+# CONFIG_CRYPTO_ANUBIS is not set
+CONFIG_CRYPTO_BLKCIPHER=m
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+CONFIG_CRYPTO_CBC=m
+# CONFIG_CRYPTO_CRC32C is not set
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HMAC=y
+# CONFIG_CRYPTO_KHAZAD is not set
+CONFIG_CRYPTO_MD4=y
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_SERPENT is not set
+CONFIG_CRYPTO_SHA1=y
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TEST is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_WP512 is not set
+CONFIG_DAVICOM_PHY=m
+# CONFIG_DDB5477 is not set
+# CONFIG_DEBUG_DRIVER is not set
+CONFIG_DEBUG_FS=y
+# CONFIG_DEBUG_INFO is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_DEBUG_RWSEMS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_VM is not set
+CONFIG_DEFAULT_BIC=y
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+CONFIG_DEFAULT_TCP_CONG="bic"
+# CONFIG_DEFAULT_VEGAS is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_DLM is not set
+# CONFIG_DM9000 is not set
+CONFIG_DMA_NEED_PCI_MAP_STATE=y
+CONFIG_DMA_NONCOHERENT=y
+CONFIG_DNOTIFY=y
+CONFIG_DUMMY=m
+CONFIG_ELF_CORE=y
+CONFIG_EQUALIZER=m
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+CONFIG_FIRMWARE_EDID=y
+# CONFIG_FIXED_PHY is not set
+CONFIG_FORCED_INLINING=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_FW_LOADER=m
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_GEN_RTC is not set
+# CONFIG_HAMRADIO is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_DEBUG_CHIP is not set
+CONFIG_HW_HAS_PCI=y
+CONFIG_HW_RANDOM=y
+CONFIG_HZ=250
+# CONFIG_HZ_100 is not set
+# CONFIG_HZ_1024 is not set
+# CONFIG_HZ_128 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_256 is not set
+# CONFIG_HZ_48 is not set
+# CONFIG_I2C is not set
+# CONFIG_IDE is not set
+CONFIG_INITRAMFS_ROOT_GID=0
+CONFIG_INITRAMFS_ROOT_UID=0
+CONFIG_INITRAMFS_SOURCE="../../root"
+CONFIG_INPUT=m
+# CONFIG_INPUT_EVDEV is not set
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_INPUT_MOUSE=y
+CONFIG_INPUT_MOUSEDEV=m
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_IPV6_PRIVACY=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_IPV6_TUNNEL=m
+# CONFIG_IP_DCCP_DEBUG is not set
+CONFIG_IP_MROUTE=y
+CONFIG_IP_NF_NAT_SNMP_BASIC=m
+CONFIG_IP_NF_NAT_TFTP=y
+CONFIG_IP_NF_NETBIOS_NS=m
+CONFIG_IP_NF_TARGET_CLUSTERIP=m
+CONFIG_IP_NF_TFTP=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+# CONFIG_IP_ROUTE_FWMARK is not set
+CONFIG_IP_SCTP=m
+CONFIG_IRQ_CPU=y
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_SUMMARY=y
+# CONFIG_JFS_FS is not set
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_KALLSYMS_EXTRA_PASS=y
+CONFIG_KEYBOARD_ATKBD=m
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KGDB is not set
+CONFIG_KMOD=y
+# CONFIG_LAN_SAA9730 is not set
+CONFIG_LBD=y
+# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
+# CONFIG_LLC2 is not set
+CONFIG_LXT_PHY=m
+# CONFIG_MACH_DECSTATION is not set
+# CONFIG_MACH_JAZZ is not set
+# CONFIG_MACH_VR41XX is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_MARVELL_PHY=m
+CONFIG_MII=m
+# CONFIG_MINIX_FS is not set
+CONFIG_MINI_FO=y
+CONFIG_MIPS=y
+# CONFIG_MIPS_ATLAS is not set
+# CONFIG_MIPS_BOSPORUS is not set
+# CONFIG_MIPS_COBALT is not set
+# CONFIG_MIPS_DB1000 is not set
+# CONFIG_MIPS_DB1100 is not set
+# CONFIG_MIPS_DB1200 is not set
+# CONFIG_MIPS_DB1500 is not set
+# CONFIG_MIPS_DB1550 is not set
+# CONFIG_MIPS_EV64120 is not set
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+# CONFIG_MIPS_MALTA is not set
+# CONFIG_MIPS_MIRAGE is not set
+# CONFIG_MIPS_MTX1 is not set
+CONFIG_MIPS_MT_DISABLED=y
+# CONFIG_MIPS_MT_SMP is not set
+# CONFIG_MIPS_MT_SMTC is not set
+# CONFIG_MIPS_PB1000 is not set
+# CONFIG_MIPS_PB1100 is not set
+# CONFIG_MIPS_PB1200 is not set
+# CONFIG_MIPS_PB1500 is not set
+# CONFIG_MIPS_PB1550 is not set
+# CONFIG_MIPS_SEAD is not set
+# CONFIG_MIPS_SIM is not set
+# CONFIG_MIPS_UNCACHED is not set
+# CONFIG_MIPS_VPE_LOADER is not set
+# CONFIG_MIPS_XXS1500 is not set
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+# CONFIG_MOMENCO_JAGUAR_ATX is not set
+# CONFIG_MOMENCO_OCELOT is not set
+# CONFIG_MOMENCO_OCELOT_3 is not set
+# CONFIG_MOMENCO_OCELOT_C is not set
+# CONFIG_MOMENCO_OCELOT_G is not set
+CONFIG_MOUSE_PS2=m
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+CONFIG_MTD=y
+# CONFIG_MTD_ABSENT is not set
+# CONFIG_MTD_BCM963XX is not set
+CONFIG_MTD_BLOCK=y
+# CONFIG_MTD_BLOCK2MTD is not set
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_STAA=y
+CONFIG_MTD_CFI_UTIL=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_DEBUG=y
+CONFIG_MTD_DEBUG_VERBOSE=1
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_OBSOLETE_CHIPS is not set
+# CONFIG_MTD_ONENAND is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_PHRAM is not set
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_BANKWIDTH=2
+CONFIG_MTD_PHYSMAP_LEN=0x800000
+CONFIG_MTD_PHYSMAP_START=0x1f000000
+# CONFIG_MTD_PLATRAM is not set
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_RAM is not set
+CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
+CONFIG_MTD_REDBOOT_PARTS=y
+CONFIG_MTD_REDBOOT_PARTS_READONLY=y
+CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_NATSEMI is not set
+# CONFIG_NE2K_PCI is not set
+CONFIG_NETFILTER_NETLINK=m
+CONFIG_NETFILTER_NETLINK_LOG=m
+CONFIG_NETFILTER_NETLINK_QUEUE=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+# CONFIG_NET_ACT_IPT is not set
+CONFIG_NET_ACT_SIMP=m
+CONFIG_NET_KEY=y
+CONFIG_NET_SCH_CLK_GETTIMEOFDAY=y
+# CONFIG_NET_SCH_CLK_JIFFIES is not set
+# CONFIG_NET_VENDOR_3COM is not set
+CONFIG_NLS=y
+CONFIG_NLS_ASCII=m
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NTFS_FS is not set
+# CONFIG_PAGE_SIZE_16KB is not set
+CONFIG_PAGE_SIZE_4KB=y
+# CONFIG_PAGE_SIZE_64KB is not set
+# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PCI_DEBUG is not set
+CONFIG_PHYLIB=m
+# CONFIG_PMC_YOSEMITE is not set
+# CONFIG_PNX8550_JBS is not set
+# CONFIG_PNX8550_V2PCI is not set
+CONFIG_POSIX_MQUEUE=y
+# CONFIG_PROVE_LOCKING is not set
+CONFIG_QSEMI_PHY=m
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_REISERFS_FS is not set
+CONFIG_RELAY=y
+# CONFIG_ROMFS_FS is not set
+# CONFIG_RTC is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_RUNTIME_DEBUG is not set
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_SCHEDSTATS is not set
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCTP_DBG_MSG is not set
+# CONFIG_SCTP_DBG_OBJCNT is not set
+CONFIG_SCTP_HMAC_MD5=y
+# CONFIG_SCTP_HMAC_NONE is not set
+# CONFIG_SCTP_HMAC_SHA1 is not set
+# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SERIAL_8250 is not set
+CONFIG_SERIO=m
+CONFIG_SERIO_I8042=m
+CONFIG_SERIO_LIBPS2=m
+# CONFIG_SERIO_PCIPS2 is not set
+# CONFIG_SERIO_RAW is not set
+CONFIG_SERIO_SERPORT=m
+# CONFIG_SGI_IP22 is not set
+# CONFIG_SGI_IP27 is not set
+# CONFIG_SGI_IP32 is not set
+CONFIG_SHAPER=m
+# CONFIG_SIBYTE_BIGSUR is not set
+# CONFIG_SIBYTE_CARMEL is not set
+# CONFIG_SIBYTE_CRHINE is not set
+# CONFIG_SIBYTE_CRHONE is not set
+# CONFIG_SIBYTE_LITTLESUR is not set
+# CONFIG_SIBYTE_PTSWARM is not set
+# CONFIG_SIBYTE_RHONE is not set
+# CONFIG_SIBYTE_SENTOSA is not set
+# CONFIG_SIBYTE_SWARM is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_SOUND is not set
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SQUASHFS_EMBEDDED=y
+CONFIG_SQUASHFS_VMALLOC=y
+CONFIG_SYN_COOKIES=y
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
+CONFIG_TCP_CONG_BIC=y
+# CONFIG_TCP_CONG_HSTCP is not set
+# CONFIG_TCP_CONG_HYBLA is not set
+# CONFIG_TCP_CONG_LP is not set
+# CONFIG_TCP_CONG_SCALABLE is not set
+# CONFIG_TCP_CONG_VEGAS is not set
+# CONFIG_TCP_CONG_VENO is not set
+CONFIG_TIPC=m
+# CONFIG_TIPC_ADVANCED is not set
+# CONFIG_TIPC_DEBUG is not set
+# CONFIG_TOSHIBA_JMR3927 is not set
+# CONFIG_TOSHIBA_RBTX4927 is not set
+# CONFIG_TOSHIBA_RBTX4938 is not set
+CONFIG_TRAD_SIGNALS=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_USB_EHCI_HCD is not set
+# CONFIG_USB_UHCI_HCD is not set
+# CONFIG_VIA_RHINE is not set
+CONFIG_VLAN_8021Q=m
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_WAN_ROUTER=m
+# CONFIG_WATCHDOG is not set
+# CONFIG_XFS_FS is not set
--- /dev/null
+#
+# Makefile for the Broadcom BCM963xx SoC specific parts of the kernel
+#
+# Copyright (C) 2004 Broadcom Corporation
+#
+obj-y := irq.o prom.o setup.o time.o ser_init.o int-handler.o info.o
+
+SRCBASE := $(TOPDIR)
+EXTRA_CFLAGS += -I$(SRCBASE)/include
--- /dev/null
+/*
+ * CFE environment variable access
+ *
+ * Copyright 2001-2003, Broadcom Corporation
+ * Copyright 2006, Felix Fietkau <nbd@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <asm/io.h>
+#include <asm/uaccess.h>
+
+#define NVRAM_SIZE (0x1ff0)
+static char _nvdata[NVRAM_SIZE];
+static char _valuestr[256];
+
+/*
+ * TLV types. These codes are used in the "type-length-value"
+ * encoding of the items stored in the NVRAM device (flash or EEPROM)
+ *
+ * The layout of the flash/nvram is as follows:
+ *
+ * <type> <length> <data ...> <type> <length> <data ...> <type_end>
+ *
+ * The type code of "ENV_TLV_TYPE_END" marks the end of the list.
+ * The "length" field marks the length of the data section, not
+ * including the type and length fields.
+ *
+ * Environment variables are stored as follows:
+ *
+ * <type_env> <length> <flags> <name> = <value>
+ *
+ * If bit 0 (low bit) is set, the length is an 8-bit value.
+ * If bit 0 (low bit) is clear, the length is a 16-bit value
+ *
+ * Bit 7 set indicates "user" TLVs. In this case, bit 0 still
+ * indicates the size of the length field.
+ *
+ * Flags are from the constants below:
+ *
+ */
+#define ENV_LENGTH_16BITS 0x00 /* for low bit */
+#define ENV_LENGTH_8BITS 0x01
+
+#define ENV_TYPE_USER 0x80
+
+#define ENV_CODE_SYS(n,l) (((n)<<1)|(l))
+#define ENV_CODE_USER(n,l) ((((n)<<1)|(l)) | ENV_TYPE_USER)
+
+/*
+ * The actual TLV types we support
+ */
+
+#define ENV_TLV_TYPE_END 0x00
+#define ENV_TLV_TYPE_ENV ENV_CODE_SYS(0,ENV_LENGTH_8BITS)
+
+/*
+ * Environment variable flags
+ */
+
+#define ENV_FLG_NORMAL 0x00 /* normal read/write */
+#define ENV_FLG_BUILTIN 0x01 /* builtin - not stored in flash */
+#define ENV_FLG_READONLY 0x02 /* read-only - cannot be changed */
+
+#define ENV_FLG_MASK 0xFF /* mask of attributes we keep */
+#define ENV_FLG_ADMIN 0x100 /* lets us internally override permissions */
+
+
+/* *********************************************************************
+ * _nvram_read(buffer,offset,length)
+ *
+ * Read data from the NVRAM device
+ *
+ * Input parameters:
+ * buffer - destination buffer
+ * offset - offset of data to read
+ * length - number of bytes to read
+ *
+ * Return value:
+ * number of bytes read, or <0 if error occured
+ ********************************************************************* */
+static int
+_nvram_read(unsigned char *nv_buf, unsigned char *buffer, int offset, int length)
+{
+ int i;
+ if (offset > NVRAM_SIZE)
+ return -1;
+
+ for ( i = 0; i < length; i++) {
+ buffer[i] = ((volatile unsigned char*)nv_buf)[offset + i];
+ }
+ return length;
+}
+
+
+static char*
+_strnchr(const char *dest,int c,size_t cnt)
+{
+ while (*dest && (cnt > 0)) {
+ if (*dest == c) return (char *) dest;
+ dest++;
+ cnt--;
+ }
+ return NULL;
+}
+
+
+
+/*
+ * Core support API: Externally visible.
+ */
+
+/*
+ * Get the value of an NVRAM variable
+ * @param name name of variable to get
+ * @return value of variable or NULL if undefined
+ */
+
+char*
+cfe_env_get(unsigned char *nv_buf, char* name)
+{
+ int size;
+ unsigned char *buffer;
+ unsigned char *ptr;
+ unsigned char *envval;
+ unsigned int reclen;
+ unsigned int rectype;
+ int offset;
+ int flg;
+
+ if (!strcmp(name, "nvram_type"))
+ return "cfe";
+
+ size = NVRAM_SIZE;
+ buffer = &_nvdata[0];
+
+ ptr = buffer;
+ offset = 0;
+
+ /* Read the record type and length */
+ if (_nvram_read(nv_buf, ptr,offset,1) != 1) {
+ goto error;
+ }
+
+ while ((*ptr != ENV_TLV_TYPE_END) && (size > 1)) {
+
+ /* Adjust pointer for TLV type */
+ rectype = *(ptr);
+ offset++;
+ size--;
+
+ /*
+ * Read the length. It can be either 1 or 2 bytes
+ * depending on the code
+ */
+ if (rectype & ENV_LENGTH_8BITS) {
+ /* Read the record type and length - 8 bits */
+ if (_nvram_read(nv_buf, ptr,offset,1) != 1) {
+ goto error;
+ }
+ reclen = *(ptr);
+ size--;
+ offset++;
+ }
+ else {
+ /* Read the record type and length - 16 bits, MSB first */
+ if (_nvram_read(nv_buf, ptr,offset,2) != 2) {
+ goto error;
+ }
+ reclen = (((unsigned int) *(ptr)) << 8) + (unsigned int) *(ptr+1);
+ size -= 2;
+ offset += 2;
+ }
+
+ if (reclen > size)
+ break; /* should not happen, bad NVRAM */
+
+ switch (rectype) {
+ case ENV_TLV_TYPE_ENV:
+ /* Read the TLV data */
+ if (_nvram_read(nv_buf, ptr,offset,reclen) != reclen)
+ goto error;
+ flg = *ptr++;
+ envval = (unsigned char *) _strnchr(ptr,'=',(reclen-1));
+ if (envval) {
+ *envval++ = '\0';
+ memcpy(_valuestr,envval,(reclen-1)-(envval-ptr));
+ _valuestr[(reclen-1)-(envval-ptr)] = '\0';
+#if 0
+ printk(KERN_INFO "NVRAM:%s=%s\n", ptr, _valuestr);
+#endif
+ if(!strcmp(ptr, name)){
+ return _valuestr;
+ }
+ if((strlen(ptr) > 1) && !strcmp(&ptr[1], name))
+ return _valuestr;
+ }
+ break;
+
+ default:
+ /* Unknown TLV type, skip it. */
+ break;
+ }
+
+ /*
+ * Advance to next TLV
+ */
+
+ size -= (int)reclen;
+ offset += reclen;
+
+ /* Read the next record type */
+ ptr = buffer;
+ if (_nvram_read(nv_buf, ptr,offset,1) != 1)
+ goto error;
+ }
+
+error:
+ return NULL;
+
+}
+
--- /dev/null
+/*
+ * $Id$
+ *
+ * Copyright (C) 2007 OpenWrt.org
+ * Copyright (C) 2007 Gabor Juhos <juhosg@freemail.hu>
+ * Copyright (C) 2007 Florian Fainelli <florian@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/types.h>
+#include <linux/autoconf.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/module.h>
+
+#include <asm/bootinfo.h>
+#include <asm/addrspace.h>
+#include <asm/string.h>
+#include <asm/mach-bcm963xx/bootloaders.h>
+
+static char *boot_loader_names[BOOT_LOADER_LAST+1] = {
+ [BOOT_LOADER_UNKNOWN] = "Unknown",
+ [BOOT_LOADER_CFE] = "CFE",
+ [BOOT_LOADER_REDBOOT] = "RedBoot",
+ [BOOT_LOADER_CFE2] = "CFEv2"
+};
+
+/* boot loaders specific definitions */
+#define CFE_EPTSEAL 0x43464531 /* CFE1 is the magic number to recognize CFE from other bootloaders */
+
+int boot_loader_type;
+/*
+ * Boot loader detection routines
+ */
+static int __init detect_cfe(void)
+{
+ /*
+ * This method only works, when we are booted directly from the CFE.
+ */
+ uint32_t cfe_handle = (uint32_t) fw_arg0;
+ uint32_t cfe_a1_val = (uint32_t) fw_arg1;
+ uint32_t cfe_entry = (uint32_t) fw_arg2;
+ uint32_t cfe_seal = (uint32_t) fw_arg3;
+
+ /* Check for CFE by finding the CFE magic number */
+ if (cfe_seal != CFE_EPTSEAL)
+ /* We are not booted from CFE */
+ return 0;
+
+ /* cfe_a1_val must be 0, because only one CPU present in the ADM5120 SoC */
+ if (cfe_a1_val != 0)
+ return 0;
+
+ /* The cfe_handle, and the cfe_entry must be kernel mode addresses */
+ if ((cfe_handle < KSEG0) || (cfe_entry < KSEG0))
+ return 0;
+
+ return 1;
+}
+
+static int __init detect_redboot(void)
+{
+ /* On Inventel Livebox, the boot loader is passed as a command line argument, check for it */
+ if (!strncmp(arcs_cmdline, "boot_loader=RedBoot", 19))
+ return 1;
+ return 0;
+}
+
+void __init detect_bootloader(void)
+{
+ if (detect_cfe()) {
+ boot_loader_type = BOOT_LOADER_CFE;
+ }
+
+ if (detect_redboot()) {
+ boot_loader_type = BOOT_LOADER_REDBOOT;
+ }
+ else {
+ /* Some devices are using CFE, but it is not detected as is */
+ boot_loader_type = BOOT_LOADER_CFE2;
+ }
+ printk("Boot loader is : %s\n", boot_loader_names[boot_loader_type]);
+}
+
+void __init detect_board(void)
+{
+ switch (boot_loader_type)
+ {
+ case BOOT_LOADER_CFE:
+ break;
+ case BOOT_LOADER_REDBOOT:
+ break;
+ default:
+ break;
+ }
+}
+
+EXPORT_SYMBOL(boot_loader_type);
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2002 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+/*
+ * Generic interrupt handler for Broadcom MIPS boards
+ */
+
+#include <linux/autoconf.h>
+
+#include <asm/asm.h>
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+
+/*
+ * MIPS IRQ Source
+ * -------- ------
+ * 0 Software (ignored)
+ * 1 Software (ignored)
+ * 2 Combined hardware interrupt (hw0)
+ * 3 Hardware
+ * 4 Hardware
+ * 5 Hardware
+ * 6 Hardware
+ * 7 R4k timer
+ */
+
+ .text
+ .set noreorder
+ .set noat
+ .align 5
+ NESTED(brcmIRQ, PT_SIZE, sp)
+ SAVE_ALL
+ CLI
+ .set noreorder
+ .set at
+
+ jal plat_irq_dispatch
+ move a0, sp
+
+ j ret_from_irq
+ nop
+
+ END(brcmIRQ)
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2002 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+/*
+ * Interrupt control functions for Broadcom 963xx MIPS boards
+ */
+
+#include <asm/atomic.h>
+
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+
+#include <asm/irq.h>
+#include <asm/mipsregs.h>
+#include <asm/addrspace.h>
+#include <asm/signal.h>
+#include <6348_map_part.h>
+#include <6348_intr.h>
+#include <bcm_map_part.h>
+#include <bcm_intr.h>
+
+static void irq_dispatch_int(struct pt_regs *regs)
+{
+ unsigned int pendingIrqs;
+ static unsigned int irqBit;
+ static unsigned int isrNumber = 31;
+
+ pendingIrqs = PERF->IrqStatus & PERF->IrqMask;
+ if (!pendingIrqs) {
+ return;
+ }
+
+ while (1) {
+ irqBit <<= 1;
+ isrNumber++;
+ if (isrNumber == 32) {
+ isrNumber = 0;
+ irqBit = 0x1;
+ }
+ if (pendingIrqs & irqBit) {
+ PERF->IrqMask &= ~irqBit; // mask
+ do_IRQ(isrNumber + INTERNAL_ISR_TABLE_OFFSET);
+ break;
+ }
+ }
+}
+
+static void irq_dispatch_ext(uint32 irq)
+{
+ if (!(PERF->ExtIrqCfg & (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT)))) {
+ printk("**** Ext IRQ mask. Should not dispatch ****\n");
+ }
+ /* disable and clear interrupt in the controller */
+ PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_CLEAR_SHFT));
+ PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT));
+ do_IRQ(irq);
+}
+
+
+extern void brcm_timer_interrupt(struct pt_regs *regs);
+
+asmlinkage void plat_irq_dispatch(struct pt_regs *regs)
+{
+ u32 cause;
+ while((cause = (read_c0_cause()& CAUSEF_IP))) {
+ if (cause & CAUSEF_IP7)
+ brcm_timer_interrupt(regs);
+ else if (cause & CAUSEF_IP2)
+ irq_dispatch_int(regs);
+ else if (cause & CAUSEF_IP3)
+ irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_0);
+ else if (cause & CAUSEF_IP4)
+ irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_1);
+ else if (cause & CAUSEF_IP5)
+ irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_2);
+ else if (cause & CAUSEF_IP6)
+ irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_3);
+ local_irq_disable();
+ }
+}
+
+
+void enable_brcm_irq(unsigned int irq)
+{
+ unsigned long flags;
+
+ local_irq_save(flags);
+ if( irq >= INTERNAL_ISR_TABLE_OFFSET ) {
+ PERF->IrqMask |= (1 << (irq - INTERNAL_ISR_TABLE_OFFSET));
+ }
+ else if (irq >= INTERRUPT_ID_EXTERNAL_0 && irq <= INTERRUPT_ID_EXTERNAL_3) {
+ /* enable and clear interrupt in the controller */
+ PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_CLEAR_SHFT));
+ PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT));
+ }
+ local_irq_restore(flags);
+}
+
+void disable_brcm_irq(unsigned int irq)
+{
+ unsigned long flags;
+
+ local_irq_save(flags);
+ if( irq >= INTERNAL_ISR_TABLE_OFFSET ) {
+ PERF->IrqMask &= ~(1 << (irq - INTERNAL_ISR_TABLE_OFFSET));
+ }
+ else if (irq >= INTERRUPT_ID_EXTERNAL_0 && irq <= INTERRUPT_ID_EXTERNAL_3) {
+ /* disable interrupt in the controller */
+ PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT));
+ }
+ local_irq_restore(flags);
+}
+
+void ack_brcm_irq(unsigned int irq)
+{
+ /* Already done in brcm_irq_dispatch */
+}
+
+unsigned int startup_brcm_irq(unsigned int irq)
+{
+ enable_brcm_irq(irq);
+
+ return 0; /* never anything pending */
+}
+
+unsigned int startup_brcm_none(unsigned int irq)
+{
+ return 0;
+}
+
+void end_brcm_irq(unsigned int irq)
+{
+ if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
+ enable_brcm_irq(irq);
+}
+
+void end_brcm_none(unsigned int irq)
+{
+}
+
+static struct hw_interrupt_type brcm_irq_type = {
+ .typename = "MIPS",
+ .startup = startup_brcm_irq,
+ .shutdown = disable_brcm_irq,
+ .enable = enable_brcm_irq,
+ .disable = disable_brcm_irq,
+ .ack = ack_brcm_irq,
+ .end = end_brcm_irq,
+ .set_affinity = NULL
+};
+
+static struct hw_interrupt_type brcm_irq_no_end_type = {
+ .typename = "MIPS",
+ .startup = startup_brcm_none,
+ .shutdown = disable_brcm_irq,
+ .enable = enable_brcm_irq,
+ .disable = disable_brcm_irq,
+ .ack = ack_brcm_irq,
+ .end = end_brcm_none,
+ .set_affinity = NULL
+};
+
+void __init arch_init_irq(void)
+{
+ int i;
+
+ clear_c0_status(ST0_BEV);
+ change_c0_status(ST0_IM, (IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3 | IE_IRQ4));
+
+ for (i = 0; i < NR_IRQS; i++) {
+ irq_desc[i].status = IRQ_DISABLED;
+ irq_desc[i].action = 0;
+ irq_desc[i].depth = 1;
+ irq_desc[i].chip = &brcm_irq_type;
+ }
+}
+
+int request_external_irq(unsigned int irq,
+ FN_HANDLER handler,
+ unsigned long irqflags,
+ const char * devname,
+ void *dev_id)
+{
+ unsigned long flags;
+
+ local_irq_save(flags);
+
+ PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_CLEAR_SHFT)); // Clear
+ PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT)); // Mask
+ PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_INSENS_SHFT)); // Edge insesnsitive
+ PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_LEVEL_SHFT)); // Level triggered
+ PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_SENSE_SHFT)); // Low level
+
+ local_irq_restore(flags);
+
+ return( request_irq(irq, handler, irqflags, devname, dev_id) );
+}
+
+/* VxWorks compatibility function(s). */
+
+unsigned int BcmHalMapInterrupt(FN_HANDLER pfunc, unsigned int param,
+ unsigned int interruptId)
+{
+ int nRet = -1;
+ char *devname;
+
+ devname = kmalloc(16, GFP_KERNEL);
+ if (devname)
+ sprintf( devname, "brcm_%d", interruptId );
+
+ /* Set the IRQ description to not automatically enable the interrupt at
+ * the end of an ISR. The driver that handles the interrupt must
+ * explicitly call BcmHalInterruptEnable or enable_brcm_irq. This behavior
+ * is consistent with interrupt handling on VxWorks.
+ */
+ irq_desc[interruptId].chip = &brcm_irq_no_end_type;
+
+ if( interruptId >= INTERNAL_ISR_TABLE_OFFSET )
+ {
+ printk("BcmHalMapInterrupt : internal IRQ\n");
+ nRet = request_irq( interruptId, pfunc, SA_SAMPLE_RANDOM | SA_INTERRUPT, devname, (void *) param );
+ }
+ else if (interruptId >= INTERRUPT_ID_EXTERNAL_0 && interruptId <= INTERRUPT_ID_EXTERNAL_3)
+ {
+ printk("BcmHalMapInterrupt : external IRQ\n");
+ nRet = request_external_irq( interruptId, pfunc, SA_SAMPLE_RANDOM | SA_INTERRUPT, devname, (void *) param );
+ }
+
+ return( nRet );
+}
+
+
+EXPORT_SYMBOL(enable_brcm_irq);
+EXPORT_SYMBOL(disable_brcm_irq);
+EXPORT_SYMBOL(request_external_irq);
+EXPORT_SYMBOL(BcmHalMapInterrupt);
+
--- /dev/null
+/*
+ * BCM947xx nvram variable access
+ *
+ * Copyright 2005, Broadcom Corporation
+ * Copyright 2006, Felix Fietkau <nbd@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+#include <linux/slab.h>
+#include <asm/byteorder.h>
+#include <asm/bootinfo.h>
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/uaccess.h>
+
+#include <nvram.h>
+
+#define MB * 1048576
+
+#define WINDOW_ADDR 0x1F000000
+#define WINDOW_SIZE 0x800000
+
+static char nvram_buf[NVRAM_SPACE];
+static int cfe_env;
+extern char *cfe_env_get(char *nv_buf, const char *name);
+
+/* Probe for NVRAM header */
+void __init early_nvram_init(void)
+{
+ struct nvram_header *header;
+ int i;
+ u32 base, lim, off;
+ u32 *src, *dst;
+
+ base = WINDOW_ADDR;
+ lim = WINDOW_SIZE;
+ cfe_env = 0;
+
+
+ /* XXX: hack for supporting the CFE environment stuff on WGT634U */
+ if (lim >= 8 MB) {
+ src = (u32 *) KSEG1ADDR(base + 8 MB - 0x20000);
+ dst = (u32 *) nvram_buf;
+
+ /* We are looking for the String gOGoBrCm */
+ if ((*src) == 0x674f476f && (*(src + 1)) == 0x4272436d) {
+ printk("early_nvram_init: EasyGate NVRAM found.\n");
+
+ for (i = 0; i < 0x1ff0; i++) {
+ if (*src == 0xFFFFFFFF)
+ break;
+ *dst++ = *src++;
+ }
+ cfe_env = 1;
+ return;
+ }
+ }
+
+ off = 0x20000;
+ while (off <= lim) {
+ /* Windowed flash access */
+ header = (struct nvram_header *) KSEG1ADDR(base + off - NVRAM_SPACE);
+ if (header->magic == NVRAM_HEADER)
+ goto found;
+ off <<= 1;
+ }
+
+ /* Try embedded NVRAM at 4 KB and 1 KB as last resorts */
+ header = (struct nvram_header *) KSEG1ADDR(base + 4096);
+ if (header->magic == NVRAM_HEADER)
+ goto found;
+
+ header = (struct nvram_header *) KSEG1ADDR(base + 1024);
+ if (header->magic == NVRAM_HEADER)
+ goto found;
+
+ printk("Found no CFE environnment\n");
+ return;
+
+found:
+ printk("Found CFE environnment\n");
+ src = (u32 *) header;
+ dst = (u32 *) nvram_buf;
+ for (i = 0; i < sizeof(struct nvram_header); i += 4)
+ *dst++ = *src++;
+ for (; i < header->len && i < NVRAM_SPACE; i += 4)
+ //*dst++ = le32_to_cpu(*src++);
+ *dst++ = be32_to_cpu(*src++);
+}
+
+char *nvram_get(const char *name)
+{
+ char *var, *value, *end, *eq;
+
+ if (!name)
+ return NULL;
+
+ if (!nvram_buf[0])
+ early_nvram_init();
+
+ if (cfe_env)
+ return cfe_env_get(nvram_buf, name);
+
+ /* Look for name=value and return value */
+ var = &nvram_buf[sizeof(struct nvram_header)];
+ end = nvram_buf + sizeof(nvram_buf) - 2;
+ end[0] = end[1] = '\0';
+ for (; *var; var = value + strlen(value) + 1) {
+ if (!(eq = strchr(var, '=')))
+ break;
+ value = eq + 1;
+ if ((eq - var) == strlen(name) && strncmp(var, name, (eq - var)) == 0)
+ return value;
+ }
+
+ return NULL;
+}
+
+EXPORT_SYMBOL(nvram_get);
--- /dev/null
+/*
+ Copyright 2004 Broadcom Corp. All Rights Reserved.
+ Copyright 2007 OpenWrt,org, Florian Fainelli <florian@openwrt.org>
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+*/
+/*
+ * prom.c: PROM library initialization code.
+ *
+ */
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/sched.h>
+#include <linux/bootmem.h>
+#include <linux/blkdev.h>
+
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+#include <asm/cpu.h>
+#include <asm/time.h>
+#include <asm/mach-bcm963xx/bootloaders.h>
+#include <asm/mach-bcm963xx/6348_map_part.h>
+
+#include "../cfe/cfe_private.h"
+
+extern void __init detect_bootloader(void);
+extern void serial_init(void);
+extern int boot_loader_type;
+
+#define MACH_BCM MACH_BCM96348
+
+const char *get_system_type(void)
+{
+ return "Broadcom BCM963xx";
+}
+
+void __init prom_init(void)
+{
+ serial_init();
+
+ printk("%s prom init\n", get_system_type() );
+
+ PERF->IrqMask = 0;
+
+ /* Detect the bootloader */
+ detect_bootloader();
+
+ /* Do further initialisations depending on the bootloader */
+ if (boot_loader_type == BOOT_LOADER_CFE || boot_loader_type == BOOT_LOADER_CFE2) {
+ cfe_setup(fw_arg0, fw_arg1, fw_arg2, fw_arg3);
+ }
+ /* Register 16MB RAM minus the ADSL SDRAM by default */
+ add_memory_region(0, (0x01000000 - ADSL_SDRAM_IMAGE_SIZE), BOOT_MEM_RAM);
+
+ mips_machgroup = MACH_GROUP_BRCM;
+ mips_machtype = MACH_BCM;
+}
+
+unsigned long __init prom_free_prom_memory(void)
+{
+ /* We do not have any memory to free */
+ return 0;
+}
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2004 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+/*
+ * Broadcom bcm63xx serial port initialization, also prepare for printk
+ * by registering with console_init
+ *
+ */
+
+#include <linux/autoconf.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/console.h>
+#include <linux/sched.h>
+
+#include <asm/addrspace.h>
+#include <asm/irq.h>
+#include <asm/reboot.h>
+#include <asm/gdb-stub.h>
+#include <asm/mc146818rtc.h>
+
+#include <bcm_map_part.h>
+#include <6348_map_part.h>
+#include <board.h>
+
+#define SER63XX_DEFAULT_BAUD 115200
+#define BD_BCM63XX_TIMER_CLOCK_INPUT (FPERIPH)
+#define stUart ((volatile Uart * const) UART_BASE)
+
+// Transmit interrupts
+#define TXINT (TXFIFOEMT | TXUNDERR | TXOVFERR)
+// Receive interrupts
+#define RXINT (RXFIFONE | RXOVFERR)
+
+/* --------------------------------------------------------------------------
+ Name: serial_init
+ Purpose: Initalize the UART
+-------------------------------------------------------------------------- */
+void __init serial_init(void)
+{
+ u32 tmpVal = SER63XX_DEFAULT_BAUD;
+ ULONG clockFreqHz;
+
+#if defined(CONFIG_BCM96345)
+ // Make sure clock is ticking
+ PERF->blkEnables |= UART_CLK_EN;
+#endif
+
+ /* Dissable channel's receiver and transmitter. */
+ stUart->control &= ~(BRGEN|TXEN|RXEN);
+
+ /*--------------------------------------------------------------------*/
+ /* Write the table value to the clock select register. */
+ /* DPullen - this is the equation to use: */
+ /* value = clockFreqHz / baud / 32-1; */
+ /* (snmod) Actually you should also take into account any necessary */
+ /* rounding. Divide by 16, look at lsb, if 0, divide by 2 */
+ /* and subtract 1. If 1, just divide by 2 */
+ /*--------------------------------------------------------------------*/
+ clockFreqHz = BD_BCM63XX_TIMER_CLOCK_INPUT;
+ tmpVal = (clockFreqHz / tmpVal) / 16;
+ if( tmpVal & 0x01 )
+ tmpVal /= 2; //Rounding up, so sub is already accounted for
+ else
+ tmpVal = (tmpVal / 2) - 1; // Rounding down so we must sub 1
+ stUart->baudword = tmpVal;
+
+ /* Finally, re-enable the transmitter and receiver. */
+ stUart->control |= (BRGEN|TXEN|RXEN);
+
+ stUart->config = (BITS8SYM | ONESTOP);
+ // Set the FIFO interrupt depth ... stUart->fifocfg = 0xAA;
+ stUart->fifoctl = RSTTXFIFOS | RSTRXFIFOS;
+ stUart->intMask = 0;
+ stUart->intMask = RXINT | TXINT;
+}
+
+
+/* prom_putc()
+ * Output a character to the UART
+ */
+void prom_putc(char c)
+{
+ /* Wait for Tx uffer to empty */
+ while (! (READ16(stUart->intStatus) & TXFIFOEMT));
+ /* Send character */
+ stUart->Data = c;
+}
+
+/* prom_puts()
+ * Write a string to the UART
+ */
+void prom_puts(const char *s)
+{
+ while (*s) {
+ if (*s == '\n') {
+ prom_putc('\r');
+ }
+ prom_putc(*s++);
+ }
+}
+
+
+/* prom_getc_nowait()
+ * Returns a character from the UART
+ * Returns -1 if no characters available or corrupted
+ */
+int prom_getc_nowait(void)
+{
+ uint16 uStatus;
+ int cData = -1;
+
+ uStatus = READ16(stUart->intStatus);
+
+ if (uStatus & RXFIFONE) { /* Do we have a character? */
+ cData = READ16(stUart->Data) & 0xff; /* Read character */
+ if (uStatus & (RXFRAMERR | RXPARERR)) { /* If we got an error, throw it away */
+ cData = -1;
+ }
+ }
+
+ return cData;
+}
+
+/* prom_getc()
+ * Returns a charcter from the serial port
+ * Will block until it receives a valid character
+*/
+char prom_getc(void)
+{
+ int cData = -1;
+
+ /* Loop until we get a valid character */
+ while(cData == -1) {
+ cData = prom_getc_nowait();
+ }
+ return (char) cData;
+}
+
+/* prom_testc()
+ * Returns 0 if no characters available
+ */
+int prom_testc(void)
+{
+ uint16 uStatus;
+
+ uStatus = READ16(stUart->intStatus);
+
+ return (uStatus & RXFIFONE);
+}
+
+#if defined (CONFIG_REMOTE_DEBUG)
+/* Prevent other code from writing to the serial port */
+void _putc(char c) { }
+void _puts(const char *ptr) { }
+#else
+/* Low level outputs call prom routines */
+void _putc(char c) {
+ prom_putc(c);
+}
+void _puts(const char *ptr) {
+ prom_puts(ptr);
+}
+#endif
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2002 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+/*
+ * Generic setup routines for Broadcom 963xx MIPS boards
+ */
+
+#include <linux/autoconf.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/kdev_t.h>
+#include <linux/types.h>
+#include <linux/console.h>
+#include <linux/sched.h>
+#include <linux/mm.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/pm.h>
+#include <linux/bootmem.h>
+
+#include <asm/addrspace.h>
+#include <asm/bcache.h>
+#include <asm/irq.h>
+#include <asm/time.h>
+#include <asm/reboot.h>
+#include <asm/gdb-stub.h>
+#include <asm/bootinfo.h>
+#include <asm/cpu.h>
+#include <asm/mach-bcm963xx/bootloaders.h>
+
+extern void brcm_time_init(void);
+extern int boot_loader_type;
+
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <bcm_map_part.h>
+#include <6348_map_part.h>
+#include <bcmpci.h>
+
+static volatile MpiRegisters * mpi = (MpiRegisters *)(MPI_BASE);
+
+/* This function should be in a board specific directory. For now,
+ * assume that all boards that include this file use a Broadcom chip
+ * with a soft reset bit in the PLL control register.
+ */
+static void brcm_machine_restart(char *command)
+{
+ const unsigned long ulSoftReset = 0x00000001;
+ unsigned long *pulPllCtrl = (unsigned long *) 0xfffe0008;
+ *pulPllCtrl |= ulSoftReset;
+}
+
+static void brcm_machine_halt(void)
+{
+ printk("System halted\n");
+ while (1);
+}
+
+static void mpi_SetLocalPciConfigReg(uint32 reg, uint32 value)
+{
+ /* write index then value */
+ mpi->pcicfgcntrl = PCI_CFG_REG_WRITE_EN + reg;;
+ mpi->pcicfgdata = value;
+}
+
+static uint32 mpi_GetLocalPciConfigReg(uint32 reg)
+{
+ /* write index then get value */
+ mpi->pcicfgcntrl = PCI_CFG_REG_WRITE_EN + reg;;
+ return mpi->pcicfgdata;
+}
+
+/*
+ * mpi_ResetPcCard: Set/Reset the PcCard
+ */
+static void mpi_ResetPcCard(int cardtype, BOOL bReset)
+{
+ if (cardtype == MPI_CARDTYPE_NONE) {
+ return;
+ }
+
+ if (cardtype == MPI_CARDTYPE_CARDBUS) {
+ bReset = ! bReset;
+ }
+
+ if (bReset) {
+ mpi->pcmcia_cntl1 = (mpi->pcmcia_cntl1 & ~PCCARD_CARD_RESET);
+ } else {
+ mpi->pcmcia_cntl1 = (mpi->pcmcia_cntl1 | PCCARD_CARD_RESET);
+ }
+}
+
+/*
+ * mpi_ConfigCs: Configure an MPI/EBI chip select
+ */
+static void mpi_ConfigCs(uint32 cs, uint32 base, uint32 size, uint32 flags)
+{
+ mpi->cs[cs].base = ((base & 0x1FFFFFFF) | size);
+ mpi->cs[cs].config = flags;
+}
+
+/*
+ * mpi_InitPcmciaSpace
+ */
+static void mpi_InitPcmciaSpace(void)
+{
+ // ChipSelect 4 controls PCMCIA Memory accesses
+ mpi_ConfigCs(PCMCIA_COMMON_BASE, pcmciaMem, EBI_SIZE_1M, (EBI_WORD_WIDE|EBI_ENABLE));
+ // ChipSelect 5 controls PCMCIA Attribute accesses
+ mpi_ConfigCs(PCMCIA_ATTRIBUTE_BASE, pcmciaAttr, EBI_SIZE_1M, (EBI_WORD_WIDE|EBI_ENABLE));
+ // ChipSelect 6 controls PCMCIA I/O accesses
+ mpi_ConfigCs(PCMCIA_IO_BASE, pcmciaIo, EBI_SIZE_64K, (EBI_WORD_WIDE|EBI_ENABLE));
+
+ mpi->pcmcia_cntl2 = ((PCMCIA_ATTR_ACTIVE << RW_ACTIVE_CNT_BIT) |
+ (PCMCIA_ATTR_INACTIVE << INACTIVE_CNT_BIT) |
+ (PCMCIA_ATTR_CE_SETUP << CE_SETUP_CNT_BIT) |
+ (PCMCIA_ATTR_CE_HOLD << CE_HOLD_CNT_BIT));
+
+ mpi->pcmcia_cntl2 |= (PCMCIA_HALFWORD_EN | PCMCIA_BYTESWAP_DIS);
+}
+
+/*
+ * cardtype_vcc_detect: PC Card's card detect and voltage sense connection
+ *
+ * CD1#/ CD2#/ VS1#/ VS2#/ Card Initial Vcc
+ * CCD1# CCD2# CVS1 CVS2 Type
+ *
+ * GND GND open open 16-bit 5 vdc
+ *
+ * GND GND GND open 16-bit 3.3 vdc
+ *
+ * GND GND open GND 16-bit x.x vdc
+ *
+ * GND GND GND GND 16-bit 3.3 & x.x vdc
+ *
+ *====================================================================
+ *
+ * CVS1 GND CCD1# open CardBus 3.3 vdc
+ *
+ * GND CVS2 open CCD2# CardBus x.x vdc
+ *
+ * GND CVS1 CCD2# open CardBus y.y vdc
+ *
+ * GND CVS2 GND CCD2# CardBus 3.3 & x.x vdc
+ *
+ * CVS2 GND open CCD1# CardBus x.x & y.y vdc
+ *
+ * GND CVS1 CCD2# open CardBus 3.3, x.x & y.y vdc
+ *
+ */
+static int cardtype_vcc_detect(void)
+{
+ uint32 data32;
+ int cardtype;
+
+ cardtype = MPI_CARDTYPE_NONE;
+ mpi->pcmcia_cntl1 = 0x0000A000; // Turn on the output enables and drive
+ // the CVS pins to 0.
+ data32 = mpi->pcmcia_cntl1;
+ switch (data32 & 0x00000003) // Test CD1# and CD2#, see if card is plugged in.
+ {
+ case 0x00000003: // No Card is in the slot.
+ printk("mpi: No Card is in the PCMCIA slot\n");
+ break;
+
+ case 0x00000002: // Partial insertion, No CD2#.
+ printk("mpi: Card in the PCMCIA slot partial insertion, no CD2 signal\n");
+ break;
+
+ case 0x00000001: // Partial insertion, No CD1#.
+ printk("mpi: Card in the PCMCIA slot partial insertion, no CD1 signal\n");
+ break;
+
+ case 0x00000000:
+ mpi->pcmcia_cntl1 = 0x0000A0C0; // Turn off the CVS output enables and
+ // float the CVS pins.
+ mdelay(1);
+ data32 = mpi->pcmcia_cntl1;
+ // Read the Register.
+ switch (data32 & 0x0000000C) // See what is on the CVS pins.
+ {
+ case 0x00000000: // CVS1 and CVS2 are tied to ground, only 1 option.
+ printk("mpi: Detected 3.3 & x.x 16-bit PCMCIA card\n");
+ cardtype = MPI_CARDTYPE_PCMCIA;
+ break;
+
+ case 0x00000004: // CVS1 is open or tied to CCD1/CCD2 and CVS2 is tied to ground.
+ // 2 valid voltage options.
+ switch (data32 & 0x00000003) // Test the values of CCD1 and CCD2.
+ {
+ case 0x00000003: // CCD1 and CCD2 are tied to 1 of the CVS pins.
+ // This is not a valid combination.
+ printk("mpi: Unknown card plugged into slot\n");
+ break;
+
+ case 0x00000002: // CCD2 is tied to either CVS1 or CVS2.
+ mpi->pcmcia_cntl1 = 0x0000A080; // Drive CVS1 to a 0.
+ mdelay(1);
+ data32 = mpi->pcmcia_cntl1;
+ if (data32 & 0x00000002) { // CCD2 is tied to CVS2, not valid.
+ printk("mpi: Unknown card plugged into slot\n");
+ } else { // CCD2 is tied to CVS1.
+ printk("mpi: Detected 3.3, x.x and y.y Cardbus card\n");
+ cardtype = MPI_CARDTYPE_CARDBUS;
+ }
+ break;
+
+ case 0x00000001: // CCD1 is tied to either CVS1 or CVS2.
+ // This is not a valid combination.
+ printk("mpi: Unknown card plugged into slot\n");
+ break;
+
+ case 0x00000000: // CCD1 and CCD2 are tied to ground.
+ printk("mpi: Detected x.x vdc 16-bit PCMCIA card\n");
+ cardtype = MPI_CARDTYPE_PCMCIA;
+ break;
+ }
+ break;
+
+ case 0x00000008: // CVS2 is open or tied to CCD1/CCD2 and CVS1 is tied to ground.
+ // 2 valid voltage options.
+ switch (data32 & 0x00000003) // Test the values of CCD1 and CCD2.
+ {
+ case 0x00000003: // CCD1 and CCD2 are tied to 1 of the CVS pins.
+ // This is not a valid combination.
+ printk("mpi: Unknown card plugged into slot\n");
+ break;
+
+ case 0x00000002: // CCD2 is tied to either CVS1 or CVS2.
+ mpi->pcmcia_cntl1 = 0x0000A040; // Drive CVS2 to a 0.
+ mdelay(1);
+ data32 = mpi->pcmcia_cntl1;
+ if (data32 & 0x00000002) { // CCD2 is tied to CVS1, not valid.
+ printk("mpi: Unknown card plugged into slot\n");
+ } else {// CCD2 is tied to CVS2.
+ printk("mpi: Detected 3.3 and x.x Cardbus card\n");
+ cardtype = MPI_CARDTYPE_CARDBUS;
+ }
+ break;
+
+ case 0x00000001: // CCD1 is tied to either CVS1 or CVS2.
+ // This is not a valid combination.
+ printk("mpi: Unknown card plugged into slot\n");
+ break;
+
+ case 0x00000000: // CCD1 and CCD2 are tied to ground.
+ cardtype = MPI_CARDTYPE_PCMCIA;
+ printk("mpi: Detected 3.3 vdc 16-bit PCMCIA card\n");
+ break;
+ }
+ break;
+
+ case 0x0000000C: // CVS1 and CVS2 are open or tied to CCD1/CCD2.
+ // 5 valid voltage options.
+
+ switch (data32 & 0x00000003) // Test the values of CCD1 and CCD2.
+ {
+ case 0x00000003: // CCD1 and CCD2 are tied to 1 of the CVS pins.
+ // This is not a valid combination.
+ printk("mpi: Unknown card plugged into slot\n");
+ break;
+
+ case 0x00000002: // CCD2 is tied to either CVS1 or CVS2.
+ // CCD1 is tied to ground.
+ mpi->pcmcia_cntl1 = 0x0000A040; // Drive CVS2 to a 0.
+ mdelay(1);
+ data32 = mpi->pcmcia_cntl1;
+ if (data32 & 0x00000002) { // CCD2 is tied to CVS1.
+ printk("mpi: Detected y.y vdc Cardbus card\n");
+ } else { // CCD2 is tied to CVS2.
+ printk("mpi: Detected x.x vdc Cardbus card\n");
+ }
+ cardtype = MPI_CARDTYPE_CARDBUS;
+ break;
+
+ case 0x00000001: // CCD1 is tied to either CVS1 or CVS2.
+ // CCD2 is tied to ground.
+
+ mpi->pcmcia_cntl1 = 0x0000A040; // Drive CVS2 to a 0.
+ mdelay(1);
+ data32 = mpi->pcmcia_cntl1;
+ if (data32 & 0x00000001) {// CCD1 is tied to CVS1.
+ printk("mpi: Detected 3.3 vdc Cardbus card\n");
+ } else { // CCD1 is tied to CVS2.
+ printk("mpi: Detected x.x and y.y Cardbus card\n");
+ }
+ cardtype = MPI_CARDTYPE_CARDBUS;
+ break;
+
+ case 0x00000000: // CCD1 and CCD2 are tied to ground.
+ cardtype = MPI_CARDTYPE_PCMCIA;
+ printk("mpi: Detected 5 vdc 16-bit PCMCIA card\n");
+ break;
+ }
+ break;
+
+ default:
+ printk("mpi: Unknown card plugged into slot\n");
+ break;
+
+ }
+ }
+ return cardtype;
+}
+
+/*
+ * mpi_DetectPcCard: Detect the plugged in PC-Card
+ * Return: < 0 => Unknown card detected
+ * 0 => No card detected
+ * 1 => 16-bit card detected
+ * 2 => 32-bit CardBus card detected
+ */
+static int mpi_DetectPcCard(void)
+{
+ int cardtype;
+
+ cardtype = cardtype_vcc_detect();
+ switch(cardtype) {
+ case MPI_CARDTYPE_PCMCIA:
+ mpi->pcmcia_cntl1 &= ~0x0000e000; // disable enable bits
+ //mpi->pcmcia_cntl1 = (mpi->pcmcia_cntl1 & ~PCCARD_CARD_RESET);
+ mpi->pcmcia_cntl1 |= (PCMCIA_ENABLE | PCMCIA_GPIO_ENABLE);
+ mpi_InitPcmciaSpace();
+ mpi_ResetPcCard(cardtype, FALSE);
+ // Hold card in reset for 10ms
+ mdelay(10);
+ mpi_ResetPcCard(cardtype, TRUE);
+ // Let card come out of reset
+ mdelay(100);
+ break;
+ case MPI_CARDTYPE_CARDBUS:
+ // 8 => CardBus Enable
+ // 1 => PCI Slot Number
+ // C => Float VS1 & VS2
+ mpi->pcmcia_cntl1 = (mpi->pcmcia_cntl1 & 0xFFFF0000) |
+ CARDBUS_ENABLE |
+ (CARDBUS_SLOT << 8)|
+ VS2_OEN |
+ VS1_OEN;
+ /* access to this memory window will be to/from CardBus */
+ mpi->l2pmremap1 |= CARDBUS_MEM;
+
+ // Need to reset the Cardbus Card. There's no CardManager to do this,
+ // and we need to be ready for PCI configuration.
+ mpi_ResetPcCard(cardtype, FALSE);
+ // Hold card in reset for 10ms
+ mdelay(10);
+ mpi_ResetPcCard(cardtype, TRUE);
+ // Let card come out of reset
+ mdelay(100);
+ break;
+ default:
+ break;
+ }
+ return cardtype;
+}
+
+static int mpi_init(void)
+{
+ unsigned long data;
+ unsigned int chipid, chiprev, sdramsize;
+
+ printk("Broadcom BCM963xx MPI\n");
+ chipid = (PERF->RevID & 0xFFFF0000) >> 16;
+ chiprev = (PERF->RevID & 0xFF);
+
+ if (boot_loader_type == BOOT_LOADER_CFE)
+ sdramsize = boot_mem_map.map[0].size;
+ else
+ sdramsize = 0x01000000;
+ /*
+ * Init the pci interface
+ */
+ data = GPIO->GPIOMode; // GPIO mode register
+ data |= GROUP2_PCI | GROUP1_MII_PCCARD; // PCI internal arbiter + Cardbus
+ GPIO->GPIOMode = data; // PCI internal arbiter
+
+ /*
+ * In the BCM6348 CardBus support is defaulted to Slot 0
+ * because there is no external IDSEL for CardBus. To disable
+ * the CardBus and allow a standard PCI card in Slot 0
+ * set the cbus_idsel field to 0x1f.
+ */
+ /*
+ uData = mpi->pcmcia_cntl1;
+ uData |= CARDBUS_IDSEL;
+ mpi->pcmcia_cntl1 = uData;
+ */
+ // Setup PCI I/O Window range. Give 64K to PCI I/O
+ mpi->l2piorange = ~(BCM_PCI_IO_SIZE_64KB-1);
+ // UBUS to PCI I/O base address
+ mpi->l2piobase = BCM_PCI_IO_BASE & BCM_PCI_ADDR_MASK;
+ // UBUS to PCI I/O Window remap
+ mpi->l2pioremap = (BCM_PCI_IO_BASE | MEM_WINDOW_EN);
+
+ // enable PCI related GPIO pins and data swap between system and PCI bus
+ mpi->locbuscntrl = (EN_PCI_GPIO | DIR_U2P_NOSWAP);
+
+ /* Enable 6348 BusMaster and Memory access mode */
+ data = mpi_GetLocalPciConfigReg(PCI_COMMAND);
+ data |= (PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+ mpi_SetLocalPciConfigReg(PCI_COMMAND, data);
+
+ /* Configure two 16 MByte PCI to System memory regions. */
+ /* These memory regions are used when PCI device is a bus master */
+ /* Accesses to the SDRAM from PCI bus will be "byte swapped" for this region */
+ mpi_SetLocalPciConfigReg(PCI_BASE_ADDRESS_3, BCM_HOST_MEM_SPACE1);
+ mpi->sp0remap = 0x0;
+
+ /* Accesses to the SDRAM from PCI bus will not be "byte swapped" for this region */
+ mpi_SetLocalPciConfigReg(PCI_BASE_ADDRESS_4, BCM_HOST_MEM_SPACE2);
+ mpi->sp1remap = 0x0;
+ mpi->pcimodesel |= (PCI_BAR2_NOSWAP | 0x40);
+
+ if ((chipid == 0x6348) && (chiprev == 0xb0)) {
+ mpi->sp0range = ~(sdramsize-1);
+ mpi->sp1range = ~(sdramsize-1);
+ }
+ /*
+ * Change 6348 PCI Cfg Reg. offset 0x40 to PCI memory read retry count infinity
+ * by set 0 in bit 8~15. This resolve read Bcm4306 srom return 0xffff in
+ * first read.
+ */
+ data = mpi_GetLocalPciConfigReg(BRCM_PCI_CONFIG_TIMER);
+ data &= ~BRCM_PCI_CONFIG_TIMER_RETRY_MASK;
+ data |= 0x00000080;
+ mpi_SetLocalPciConfigReg(BRCM_PCI_CONFIG_TIMER, data);
+
+ /* enable pci interrupt */
+ mpi->locintstat |= (EXT_PCI_INT << 16);
+
+ mpi_DetectPcCard();
+
+ ioport_resource.start = BCM_PCI_IO_BASE;
+ ioport_resource.end = BCM_PCI_IO_BASE + BCM_PCI_IO_SIZE_64KB;
+
+#if defined(CONFIG_USB)
+ PERF->blkEnables |= USBH_CLK_EN;
+ mdelay(100);
+ *USBH_NON_OHCI = NON_OHCI_BYTE_SWAP;
+#endif
+
+ return 0;
+}
+
+void __init plat_mem_setup(void)
+{
+ _machine_restart = brcm_machine_restart;
+ _machine_halt = brcm_machine_halt;
+ pm_power_off = brcm_machine_halt;
+
+ board_time_init = brcm_time_init;
+
+ mpi_init();
+}
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2004 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+/*
+ * Setup time for Broadcom 963xx MIPS boards
+ */
+
+#include <linux/autoconf.h>
+#include <linux/init.h>
+#include <linux/kernel_stat.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/time.h>
+#include <linux/timex.h>
+
+#include <asm/mipsregs.h>
+#include <asm/ptrace.h>
+#include <asm/div64.h>
+#include <asm/time.h>
+
+#include <6348_map_part.h>
+#include <6348_intr.h>
+#include <bcm_map_part.h>
+#include <bcm_intr.h>
+
+static unsigned long r4k_offset; /* Amount to increment compare reg each time */
+static unsigned long r4k_cur; /* What counter should be at next timer irq */
+
+/* *********************************************************************
+ * calculateCpuSpeed()
+ * Calculate the BCM6348 CPU speed by reading the PLL strap register
+ * and applying the following formula:
+ * cpu_clk = (.25 * 64MHz freq) * (N1 + 1) * (N2 + 2) / (M1_CPU + 1)
+ * Input parameters:
+ * none
+ * Return value:
+ * none
+ ********************************************************************* */
+
+static inline unsigned long __init calculateCpuSpeed(void)
+{
+ u32 pllStrap = PERF->PllStrap;
+ int n1 = (pllStrap & PLL_N1_MASK) >> PLL_N1_SHFT;
+ int n2 = (pllStrap & PLL_N2_MASK) >> PLL_N2_SHFT;
+ int m1cpu = (pllStrap & PLL_M1_CPU_MASK) >> PLL_M1_CPU_SHFT;
+
+ return (16 * (n1 + 1) * (n2 + 2) / (m1cpu + 1)) * 1000000;
+}
+
+
+static inline unsigned long __init cal_r4koff(void)
+{
+ mips_hpt_frequency = calculateCpuSpeed() / 2;
+ return (mips_hpt_frequency / HZ);
+}
+
+
+/*
+ * There are a lot of conceptually broken versions of the MIPS timer interrupt
+ * handler floating around. This one is rather different, but the algorithm
+ * is provably more robust.
+ */
+irqreturn_t brcm_timer_interrupt(struct pt_regs *regs)
+{
+ int irq = MIPS_TIMER_INT;
+
+ irq_enter();
+ kstat_this_cpu.irqs[irq]++;
+
+ timer_interrupt(irq, regs);
+ irq_exit();
+ return IRQ_HANDLED;
+}
+
+
+void __init brcm_time_init(void)
+{
+ unsigned int est_freq, flags;
+ local_irq_save(flags);
+
+ printk("calculating r4koff... ");
+ r4k_offset = cal_r4koff();
+ printk("%08lx(%d)\n", r4k_offset, (int)r4k_offset);
+
+ est_freq = 2 * r4k_offset * HZ;
+ est_freq += 5000; /* round */
+ est_freq -= est_freq % 10000;
+ printk("CPU frequency %d.%02d MHz\n", est_freq / 1000000,
+ (est_freq % 1000000) * 100 / 1000000);
+ local_irq_restore(flags);
+}
+
+
+void __init plat_timer_setup(struct irqaction *irq)
+{
+ r4k_cur = (read_c0_count() + r4k_offset);
+ write_c0_compare(r4k_cur);
+ set_c0_status(IE_IRQ5);
+}
--- /dev/null
+/*
+ * Watchdog driver for the BCM963xx devices
+ *
+ * Copyright (C) 2007 OpenWrt.org
+ * Florian Fainelli <florian@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/miscdevice.h>
+#include <linux/fs.h>
+#include <linux/init.h>
+#include <linux/notifier.h>
+#include <linux/watchdog.h>
+#include <linux/timer.h>
+#include <linux/jiffies.h>
+#include <linux/completion.h>
+#include <linux/ioport.h>
+
+typedef struct bcm963xx_timer {
+ unsigned short unused0;
+ unsigned char timer_mask;
+#define TIMER0EN 0x01
+#define TIMER1EN 0x02
+#define TIMER2EN 0x04
+ unsigned char timer_ints;
+#define TIMER0 0x01
+#define TIMER1 0x02
+#define TIMER2 0x04
+#define WATCHDOG 0x08
+ unsigned long timer_ctl0;
+ unsigned long timer_ctl1;
+ unsigned long timer_ctl2;
+#define TIMERENABLE 0x80000000
+#define RSTCNTCLR 0x40000000
+ unsigned long timer_cnt0;
+ unsigned long timer_cnt1;
+ unsigned long timer_cnt2;
+ unsigned long wdt_def_count;
+
+ /* Write 0xff00 0x00ff to Start timer
+ * Write 0xee00 0x00ee to Stop and re-load default count
+ * Read from this register returns current watch dog count
+ */
+ unsigned long wdt_ctl;
+
+ /* Number of 40-MHz ticks for WD Reset pulse to last */
+ unsigned long wdt_rst_count;
+} bcm963xx_timer;
+
+static struct bcm963xx_wdt_device {
+ struct completion stop;
+ volatile int running;
+ struct timer_list timer;
+ volatile int queue;
+ int default_ticks;
+ unsigned long inuse;
+} bcm963xx_wdt_device;
+
+static int ticks = 1000;
+
+#define WDT_BASE 0xfffe0200
+#define WDT ((volatile bcm963xx_timer * const) WDT_BASE)
+
+#define BCM963XX_INTERVAL (HZ/10+1)
+
+static void bcm963xx_wdt_trigger(unsigned long unused)
+{
+ if (bcm963xx_wdt_device.running)
+ ticks--;
+
+ /* Load the default ticking value into the reset counter register */
+ WDT->wdt_rst_count = bcm963xx_wdt_device.default_ticks;
+
+ if (bcm963xx_wdt_device.queue && ticks) {
+ bcm963xx_wdt_device.timer.expires = jiffies + BCM963XX_INTERVAL;
+ add_timer(&bcm963xx_wdt_device.timer);
+ }
+ else {
+ complete(&bcm963xx_wdt_device.stop);
+ }
+}
+
+static void bcm963xx_wdt_reset(void)
+{
+ ticks = bcm963xx_wdt_device.default_ticks;
+}
+
+static void bcm963xx_wdt_start(void)
+{
+ if (!bcm963xx_wdt_device.queue) {
+ bcm963xx_wdt_device.queue;
+ /* Enable the watchdog by writing 0xff00 ,then 0x00ff to the control register */
+ WDT->wdt_ctl = 0xff00;
+ WDT->wdt_ctl = 0x00ff;
+ bcm963xx_wdt_device.timer.expires = jiffies + BCM963XX_INTERVAL;
+ add_timer(&bcm963xx_wdt_device.timer);
+ }
+ bcm963xx_wdt_device.running++;
+}
+
+static int bcm963xx_wdt_stop(void)
+{
+ if (bcm963xx_wdt_device.running)
+ bcm963xx_wdt_device.running = 0;
+
+ ticks = bcm963xx_wdt_device.default_ticks;
+
+ /* Stop the watchdog by writing 0xee00 then 0x00ee to the control register */
+ WDT->wdt_ctl = 0xee00;
+ WDT->wdt_ctl = 0x00ee;
+
+ return -EIO;
+}
+
+static int bcm963xx_wdt_open(struct inode *inode, struct file *file)
+{
+ if (test_and_set_bit(0, &bcm963xx_wdt_device.inuse))
+ return -EBUSY;
+ return nonseekable_open(inode, file);
+}
+
+static int bcm963xx_wdt_release(struct inode *inode, struct file *file)
+{
+ clear_bit(0, &bcm963xx_wdt_device.inuse);
+ return 0;
+}
+
+static int bcm963xx_wdt_ioctl(struct inode *inode, struct file *file,
+ unsigned int cmd, unsigned long arg)
+{
+ void __user *argp = (void __user *)arg;
+ unsigned int value;
+
+ static struct watchdog_info ident = {
+ .options = WDIOF_CARDRESET,
+ .identity = "BCM963xx WDT",
+ };
+
+ switch (cmd) {
+ case WDIOC_KEEPALIVE:
+ bcm963xx_wdt_reset();
+ break;
+ case WDIOC_GETSTATUS:
+ /* Reading from the control register will return the current value */
+ value = WDT->wdt_ctl;
+ if ( copy_to_user(argp, &value, sizeof(int)) )
+ return -EFAULT;
+ break;
+ case WDIOC_GETSUPPORT:
+ if ( copy_to_user(argp, &ident, sizeof(ident)) )
+ return -EFAULT;
+ break;
+ case WDIOC_SETOPTIONS:
+ if ( copy_from_user(&value, argp, sizeof(int)) )
+ return -EFAULT;
+ switch(value) {
+ case WDIOS_ENABLECARD:
+ bcm963xx_wdt_start();
+ break;
+ case WDIOS_DISABLECARD:
+ bcm963xx_wdt_stop();
+ break;
+ default:
+ return -EINVAL;
+ }
+ break;
+ default:
+ return -ENOTTY;
+ }
+ return 0;
+}
+
+static int bcm963xx_wdt_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
+{
+ if (!count)
+ return -EIO;
+ bcm963xx_wdt_reset();
+ return count;
+}
+
+static const struct file_operations bcm963xx_wdt_fops = {
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = bcm963xx_wdt_write,
+ .ioctl = bcm963xx_wdt_ioctl,
+ .open = bcm963xx_wdt_open,
+ .release = bcm963xx_wdt_release,
+};
+
+static struct miscdevice bcm963xx_wdt_miscdev = {
+ .minor = WATCHDOG_MINOR,
+ .name = "watchdog",
+ .fops = &bcm963xx_wdt_fops,
+};
+
+static void __exit bcm963xx_wdt_exit(void)
+{
+ if (bcm963xx_wdt_device.queue ){
+ bcm963xx_wdt_device.queue = 0;
+ wait_for_completion(&bcm963xx_wdt_device.stop);
+ }
+ misc_deregister(&bcm963xx_wdt_miscdev);
+}
+
+static int __init bcm963xx_wdt_init(void)
+{
+ int ret = 0;
+
+ printk("Broadcom BCM963xx Watchdog timer\n");
+
+ ret = misc_register(&bcm963xx_wdt_miscdev);
+ if (ret) {
+ printk(KERN_CRIT "Cannot register miscdev on minor=%d (err=%d)\n", WATCHDOG_MINOR, ret);
+ return ret;
+ }
+ init_completion(&bcm963xx_wdt_device.stop);
+ bcm963xx_wdt_device.queue = 0;
+
+ clear_bit(0, &bcm963xx_wdt_device.inuse);
+
+ init_timer(&bcm963xx_wdt_device.timer);
+ bcm963xx_wdt_device.timer.function = bcm963xx_wdt_trigger;
+ bcm963xx_wdt_device.timer.data = 0;
+
+ bcm963xx_wdt_device.default_ticks = ticks;
+ return ret;
+}
+
+
+module_init(bcm963xx_wdt_init);
+module_exit(bcm963xx_wdt_exit);
+
+MODULE_AUTHOR("Florian Fainelli <florian@openwrt.org>");
+MODULE_DESCRIPTION("Broadcom BCM963xx Watchdog driver");
+MODULE_LICENSE("GPL");
--- /dev/null
+#
+# Makefile for the Broadcom Common Firmware Environment support
+#
+
+obj-y += cfe.o
--- /dev/null
+/*
+ * Broadcom Common Firmware Environment (CFE) support
+ *
+ * Copyright 2000, 2001, 2002
+ * Broadcom Corporation. All rights reserved.
+ *
+ * Copyright (C) 2006 Michael Buesch
+ *
+ * Original Authors: Mitch Lichtenberg, Chris Demetriou
+ *
+ * This software is furnished under license and may be used and copied only
+ * in accordance with the following terms and conditions. Subject to these
+ * conditions, you may download, copy, install, use, modify and distribute
+ * modified or unmodified copies of this software in source and/or binary
+ * form. No title or ownership is transferred hereby.
+ *
+ * 1) Any source code used, modified or distributed must reproduce and
+ * retain this copyright notice and list of conditions as they appear in
+ * the source file.
+ *
+ * 2) No right is granted to use any trade name, trademark, or logo of
+ * Broadcom Corporation. The "Broadcom Corporation" name may not be
+ * used to endorse or promote products derived from this software
+ * without the prior written permission of Broadcom Corporation.
+ *
+ * 3) THIS SOFTWARE IS PROVIDED "AS-IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
+ * NON-INFRINGEMENT ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM BE LIABLE
+ * FOR ANY DAMAGES WHATSOEVER, AND IN PARTICULAR, BROADCOM SHALL NOT BE
+ * LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE), EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <linux/init.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/spinlock.h>
+#include <asm/cfe.h>
+
+#include "cfe_private.h"
+
+
+static cfe_uint_t cfe_handle;
+static int (*cfe_trampoline)(long handle, long iocb);
+
+
+#include <linux/kernel.h>
+
+void __init cfe_setup(unsigned long fwarg0, unsigned long fwarg1,
+ unsigned long fwarg2, unsigned long fwarg3)
+{
+ if (fwarg3 == 0x80300000) {
+ /* WRT54G workaround */
+ fwarg3 = CFE_EPTSEAL;
+ fwarg2 = 0xBFC00500;
+ }
+ if (fwarg3 != CFE_EPTSEAL) {
+ /* We are not booted from CFE */
+ return;
+ }
+ if (fwarg1 == 0) {
+ /* We are on the boot CPU */
+ cfe_handle = (cfe_uint_t)fwarg0;
+ cfe_trampoline = CFE_TO_PTR(fwarg2);
+ }
+}
+
+int cfe_vprintk(const char *fmt, va_list args)
+{
+ static char buffer[1024];
+ static DEFINE_SPINLOCK(lock);
+ static const char pfx[] = "CFE-console: ";
+ static const size_t pfx_len = sizeof(pfx) - 1;
+ unsigned long flags;
+ int len, cnt, pos;
+ int handle;
+ int res;
+
+ if (!cfe_present())
+ return -ENODEV;
+
+ spin_lock_irqsave(&lock, flags);
+ handle = cfe_getstdhandle(CFE_STDHANDLE_CONSOLE);
+ if (CFE_ISERR(handle)) {
+ len = -EIO;
+ goto out;
+ }
+ strcpy(buffer, pfx);
+ len = vscnprintf(buffer + pfx_len,
+ sizeof(buffer) - pfx_len - 2,
+ fmt, args);
+ len += pfx_len;
+ /* The CFE console requires CR-LF line-ends.
+ * Add a CR, if we only terminate lines with a LF.
+ * This does only fix CR-LF at the end of the string.
+ * So for multiple lines, use multiple cfe_vprintk calls.
+ */
+ if (len > 1 &&
+ buffer[len - 1] == '\n' && buffer[len - 2] != '\r') {
+ buffer[len - 1] = '\r';
+ buffer[len] = '\n';
+ len += 1;
+ }
+ cnt = len;
+ pos = 0;
+ while (cnt > 0) {
+ res = cfe_write(handle, buffer + pos, len - pos);
+ if (CFE_ISERR(res)) {
+ len = -EIO;
+ goto out;
+ }
+ cnt -= res;
+ pos += res;
+ }
+out:
+ spin_unlock_irqrestore(&lock, flags);
+
+ return len;
+}
+
+int cfe_printk(const char *fmt, ...)
+{
+ va_list args;
+ int res;
+
+ va_start(args, fmt);
+ res = cfe_vprintk(fmt, args);
+ va_end(args);
+
+ return res;
+}
+
+static int cfe_iocb_dispatch(struct cfe_iocb *iocb)
+{
+ if (!cfe_present())
+ return CFE_ERR_UNSUPPORTED;
+ return cfe_trampoline((long)cfe_handle, (long)iocb);
+}
+
+int cfe_present(void)
+{
+ return (cfe_trampoline != NULL);
+}
+
+int cfe_close(int handle)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_DEV_CLOSE;
+ iocb.handle = handle;
+
+ err = cfe_iocb_dispatch(&iocb);
+
+ return (CFE_ISERR(err)) ? err : iocb.status;
+}
+
+int cfe_cpu_start(int cpu, void (*fn)(void), long sp, long gp, long a1)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_FW_CPUCTL;
+ iocb.psize = sizeof(struct cfe_iocb_cpuctl);
+ iocb.cpuctl.number = cpu;
+ iocb.cpuctl.command = CFE_CPU_CMD_START;
+ iocb.cpuctl.gp = gp;
+ iocb.cpuctl.sp = sp;
+ iocb.cpuctl.a1 = a1;
+ iocb.cpuctl.start_addr = (long)fn;
+
+ err = cfe_iocb_dispatch(&iocb);
+
+ return (CFE_ISERR(err)) ? err : iocb.status;
+}
+
+int cfe_cpu_stop(int cpu)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_FW_CPUCTL;
+ iocb.psize = sizeof(struct cfe_iocb_cpuctl);
+ iocb.cpuctl.number = cpu;
+ iocb.cpuctl.command = CFE_CPU_CMD_STOP;
+
+ err = cfe_iocb_dispatch(&iocb);
+
+ return (CFE_ISERR(err)) ? err : iocb.status;
+}
+
+int cfe_enumenv(int idx, char *name, int namelen, char *val, int vallen)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_ENV_ENUM;
+ iocb.psize = sizeof(struct cfe_iocb_envbuf);
+ iocb.envbuf.index = idx;
+ iocb.envbuf.name = PTR_TO_CFE(name);
+ iocb.envbuf.name_len = namelen;
+ iocb.envbuf.val = PTR_TO_CFE(val);
+ iocb.envbuf.val_len = vallen;
+
+ err = cfe_iocb_dispatch(&iocb);
+
+ return (CFE_ISERR(err)) ? err : iocb.status;
+}
+
+int cfe_enumdev(int idx, char *name, int namelen)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+
+ iocb.fcode = CFE_CMD_DEV_ENUM;
+ iocb.psize = sizeof(struct cfe_iocb_envbuf);
+ iocb.envbuf.index = idx;
+ iocb.envbuf.name = PTR_TO_CFE(name);
+ iocb.envbuf.name_len = namelen;
+
+ err = cfe_iocb_dispatch(&iocb);
+
+ return (CFE_ISERR(err)) ? err : iocb.status;
+}
+
+int cfe_enummem(int idx, int flags, u64 *start, u64 *length,
+ u64 *type)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+
+ iocb.fcode = CFE_CMD_FW_MEMENUM;
+ iocb.flags = flags;
+ iocb.psize = sizeof(struct cfe_iocb_meminfo);
+ iocb.meminfo.index = idx;
+
+ err = cfe_iocb_dispatch(&iocb);
+ if (CFE_ISERR(err))
+ return err;
+ if (!CFE_ISERR(iocb.status)) {
+ *start = iocb.meminfo.addr;
+ *length = iocb.meminfo.size;
+ *type = iocb.meminfo.type;
+ }
+
+ return iocb.status;
+}
+
+int cfe_exit(int warm, int status)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+printk("CFE REBOOT\n");
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_FW_RESTART;
+ if (warm)
+ iocb.flags = CFE_FLG_WARMSTART;
+ iocb.psize = sizeof(struct cfe_iocb_exitstat);
+ iocb.exitstat.status = status;
+
+printk("CALL\n");
+ err = cfe_iocb_dispatch(&iocb);
+printk("DONE\n");
+
+ return (CFE_ISERR(err)) ? err : iocb.status;
+}
+
+int cfe_flushcache(int flags)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_FW_FLUSHCACHE;
+ iocb.flags = flags;
+
+ err = cfe_iocb_dispatch(&iocb);
+
+ return (CFE_ISERR(err)) ? err : iocb.status;
+}
+
+int cfe_getdevinfo(char *name)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_DEV_GETINFO;
+ iocb.psize = sizeof(struct cfe_iocb_buf);
+ iocb.buffer.ptr = PTR_TO_CFE(name);
+ iocb.buffer.length = strlen(name);
+
+ err = cfe_iocb_dispatch(&iocb);
+ if (CFE_ISERR(err))
+ return err;
+ if (CFE_ISERR(iocb.status))
+ return iocb.status;
+
+ return iocb.buffer.devflags;
+}
+
+int cfe_getenv(char *name, char *dest, int destlen)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ dest[0] = '\0';
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_ENV_GET;
+ iocb.psize = sizeof(struct cfe_iocb_envbuf);
+ iocb.envbuf.name = PTR_TO_CFE(name);
+ iocb.envbuf.name_len = strlen(name);
+ iocb.envbuf.val = PTR_TO_CFE(dest);
+ iocb.envbuf.val_len = destlen;
+
+ err = cfe_iocb_dispatch(&iocb);
+
+ return (CFE_ISERR(err)) ? err : iocb.status;
+}
+
+int cfe_getfwinfo(struct cfe_fwinfo *info)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_FW_GETINFO;
+ iocb.psize = sizeof(struct cfe_iocb_fwinfo);
+
+ err = cfe_iocb_dispatch(&iocb);
+ if (CFE_ISERR(err))
+ return err;
+ if (CFE_ISERR(iocb.status))
+ return err;
+
+ info->version = iocb.fwinfo.version;
+ info->totalmem = iocb.fwinfo.totalmem;
+ info->flags = iocb.fwinfo.flags;
+ info->boardid = iocb.fwinfo.boardid;
+ info->bootarea_va = iocb.fwinfo.bootarea_va;
+ info->bootarea_pa = iocb.fwinfo.bootarea_pa;
+ info->bootarea_size = iocb.fwinfo.bootarea_size;
+
+ return iocb.status;
+}
+
+int cfe_getstdhandle(int handletype)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_DEV_GETHANDLE;
+ iocb.flags = handletype;
+
+ err = cfe_iocb_dispatch(&iocb);
+ if (CFE_ISERR(err))
+ return err;
+ if (CFE_ISERR(iocb.status))
+ return iocb.status;
+
+ return iocb.handle;
+}
+
+int cfe_getticks(s64 *ticks)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_FW_GETTIME;
+ iocb.psize = sizeof(struct cfe_iocb_time);
+
+ err = cfe_iocb_dispatch(&iocb);
+ if (CFE_ISERR(err))
+ return err;
+ if (!CFE_ISERR(iocb.status))
+ *ticks = iocb.time.ticks;
+
+ return iocb.status;
+}
+
+int cfe_inpstat(int handle)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_DEV_INPSTAT;
+ iocb.handle = handle;
+ iocb.psize = sizeof(struct cfe_iocb_inpstat);
+
+ err = cfe_iocb_dispatch(&iocb);
+ if (CFE_ISERR(err))
+ return err;
+ if (CFE_ISERR(iocb.status))
+ return iocb.status;
+
+ return iocb.inpstat.status;
+}
+
+int cfe_ioctl(int handle, unsigned int ioctlnum,
+ unsigned char *buffer, int length,
+ int *retlen, u64 offset)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_DEV_IOCTL;
+ iocb.handle = handle;
+ iocb.psize = sizeof(struct cfe_iocb_buf);
+ iocb.buffer.offset = offset;
+ iocb.buffer.ioctlcmd = ioctlnum;
+ iocb.buffer.ptr = PTR_TO_CFE(buffer);
+ iocb.buffer.length = length;
+
+ err = cfe_iocb_dispatch(&iocb);
+ if (CFE_ISERR(err))
+ return err;
+ if (CFE_ISERR(iocb.status))
+ return iocb.status;
+ if (retlen)
+ *retlen = iocb.buffer.retlen;
+
+ return iocb.status;
+}
+
+int cfe_open(char *name)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_DEV_OPEN;
+ iocb.psize = sizeof(struct cfe_iocb_buf);
+ iocb.buffer.ptr = PTR_TO_CFE(name);
+ iocb.buffer.length = strlen(name);
+
+ err = cfe_iocb_dispatch(&iocb);
+ if (CFE_ISERR(err))
+ return err;
+ if (CFE_ISERR(iocb.status))
+ return iocb.status;
+
+ return iocb.handle;
+}
+
+int cfe_read(int handle, unsigned char *buffer, int length)
+{
+ return cfe_readblk(handle, 0, buffer, length);
+}
+
+int cfe_readblk(int handle, s64 offset, unsigned char *buffer, int length)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_DEV_READ;
+ iocb.handle = handle;
+ iocb.psize = sizeof(struct cfe_iocb_buf);
+ iocb.buffer.offset = offset;
+ iocb.buffer.ptr = PTR_TO_CFE(buffer);
+ iocb.buffer.length = length;
+
+ err = cfe_iocb_dispatch(&iocb);
+ if (CFE_ISERR(err))
+ return err;
+ if (CFE_ISERR(iocb.status))
+ return iocb.status;
+
+ return iocb.buffer.retlen;
+}
+
+int cfe_setenv(char *name, char *val)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_ENV_SET;
+ iocb.psize = sizeof(struct cfe_iocb_envbuf);
+ iocb.envbuf.name = PTR_TO_CFE(name);
+ iocb.envbuf.name_len = strlen(name);
+ iocb.envbuf.val = PTR_TO_CFE(val);
+ iocb.envbuf.val_len = strlen(val);
+
+ err = cfe_iocb_dispatch(&iocb);
+
+ return (CFE_ISERR(err)) ? err : iocb.status;
+}
+
+int cfe_write(int handle, unsigned char *buffer, int length)
+{
+ return cfe_writeblk(handle, 0, buffer, length);
+}
+
+int cfe_writeblk(int handle, s64 offset, unsigned char *buffer, int length)
+{
+ struct cfe_iocb iocb;
+ int err;
+
+ memset(&iocb, 0, sizeof(iocb));
+ iocb.fcode = CFE_CMD_DEV_WRITE;
+ iocb.handle = handle;
+ iocb.psize = sizeof(struct cfe_iocb_buf);
+ iocb.buffer.offset = offset;
+ iocb.buffer.ptr = PTR_TO_CFE(buffer);
+ iocb.buffer.length = length;
+
+ err = cfe_iocb_dispatch(&iocb);
+ if (CFE_ISERR(err))
+ return err;
+ if (CFE_ISERR(iocb.status))
+ return iocb.status;
+
+ return iocb.buffer.retlen;
+}
--- /dev/null
+/*
+ * Broadcom Common Firmware Environment (CFE) support
+ *
+ * Copyright 2000, 2001, 2002
+ * Broadcom Corporation. All rights reserved.
+ *
+ * Copyright (C) 2006 Michael Buesch
+ *
+ * Original Authors: Mitch Lichtenberg, Chris Demetriou
+ *
+ * This software is furnished under license and may be used and copied only
+ * in accordance with the following terms and conditions. Subject to these
+ * conditions, you may download, copy, install, use, modify and distribute
+ * modified or unmodified copies of this software in source and/or binary
+ * form. No title or ownership is transferred hereby.
+ *
+ * 1) Any source code used, modified or distributed must reproduce and
+ * retain this copyright notice and list of conditions as they appear in
+ * the source file.
+ *
+ * 2) No right is granted to use any trade name, trademark, or logo of
+ * Broadcom Corporation. The "Broadcom Corporation" name may not be
+ * used to endorse or promote products derived from this software
+ * without the prior written permission of Broadcom Corporation.
+ *
+ * 3) THIS SOFTWARE IS PROVIDED "AS-IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
+ * NON-INFRINGEMENT ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM BE LIABLE
+ * FOR ANY DAMAGES WHATSOEVER, AND IN PARTICULAR, BROADCOM SHALL NOT BE
+ * LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE), EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#ifndef LINUX_CFE_PRIVATE_H_
+#define LINUX_CFE_PRIVATE_H_
+
+#ifndef __ASSEMBLY__
+
+/* Seal indicating CFE's presence, passed to the kernel. */
+#define CFE_EPTSEAL 0x43464531
+
+#define CFE_CMD_FW_GETINFO 0
+#define CFE_CMD_FW_RESTART 1
+#define CFE_CMD_FW_BOOT 2
+#define CFE_CMD_FW_CPUCTL 3
+#define CFE_CMD_FW_GETTIME 4
+#define CFE_CMD_FW_MEMENUM 5
+#define CFE_CMD_FW_FLUSHCACHE 6
+
+#define CFE_CMD_DEV_GETHANDLE 9
+#define CFE_CMD_DEV_ENUM 10
+#define CFE_CMD_DEV_OPEN 11
+#define CFE_CMD_DEV_INPSTAT 12
+#define CFE_CMD_DEV_READ 13
+#define CFE_CMD_DEV_WRITE 14
+#define CFE_CMD_DEV_IOCTL 15
+#define CFE_CMD_DEV_CLOSE 16
+#define CFE_CMD_DEV_GETINFO 17
+
+#define CFE_CMD_ENV_ENUM 20
+#define CFE_CMD_ENV_GET 22
+#define CFE_CMD_ENV_SET 23
+#define CFE_CMD_ENV_DEL 24
+
+#define CFE_CMD_MAX 32
+
+#define CFE_CMD_VENDOR_USE 0x8000 /* codes above this are for customer use */
+
+typedef u64 cfe_uint_t;
+typedef s64 cfe_int_t;
+typedef s64 cfe_ptr_t;
+
+/* Cast a pointer from native to CFE-API pointer and back */
+#define CFE_TO_PTR(p) ((void *)(unsigned long)(p))
+#define PTR_TO_CFE(p) ((cfe_ptr_t)(unsigned long)(p))
+
+struct cfe_iocb_buf {
+ cfe_uint_t offset; /* offset on device (bytes) */
+ cfe_ptr_t ptr; /* pointer to a buffer */
+ cfe_uint_t length; /* length of this buffer */
+ cfe_uint_t retlen; /* returned length (for read ops) */
+ union {
+ cfe_uint_t ioctlcmd; /* IOCTL command (used only for IOCTLs) */
+ cfe_uint_t devflags; /* Returned device info flags */
+ };
+};
+
+struct cfe_iocb_inpstat {
+ cfe_uint_t status; /* 1 means input available */
+};
+
+struct cfe_iocb_envbuf {
+ cfe_int_t index; /* 0-based enumeration index */
+ cfe_ptr_t name; /* name string buffer */
+ cfe_int_t name_len; /* size of name buffer */
+ cfe_ptr_t val; /* value string buffer */
+ cfe_int_t val_len; /* size of value string buffer */
+};
+
+struct cfe_iocb_cpuctl {
+ cfe_uint_t number; /* cpu number to control */
+ cfe_uint_t command; /* command to issue to CPU */
+ cfe_uint_t start_addr; /* CPU start address */
+ cfe_uint_t gp; /* starting GP value */
+ cfe_uint_t sp; /* starting SP value */
+ cfe_uint_t a1; /* starting A1 value */
+};
+
+struct cfe_iocb_time {
+ cfe_int_t ticks; /* current time in ticks */
+};
+
+struct cfe_iocb_exitstat {
+ cfe_int_t status;
+};
+
+struct cfe_iocb_meminfo {
+ cfe_int_t index; /* 0-based enumeration index */
+ cfe_int_t type; /* type of memory block */
+ cfe_uint_t addr; /* physical start address */
+ cfe_uint_t size; /* block size */
+};
+
+struct cfe_iocb_fwinfo {
+ cfe_int_t version; /* major, minor, eco version */
+ cfe_int_t totalmem; /* total installed mem */
+ cfe_int_t flags; /* various flags */
+ cfe_int_t boardid; /* board ID */
+ cfe_int_t bootarea_va; /* VA of boot area */
+ cfe_int_t bootarea_pa; /* PA of boot area */
+ cfe_int_t bootarea_size; /* size of boot area */
+ cfe_int_t reserved1;
+ cfe_int_t reserved2;
+ cfe_int_t reserved3;
+};
+
+/* CFE I/O Control Block */
+struct cfe_iocb {
+ cfe_uint_t fcode; /* IOCB function code */
+ cfe_int_t status; /* return status */
+ cfe_int_t handle; /* file/device handle */
+ cfe_uint_t flags; /* flags for this IOCB */
+ cfe_uint_t psize; /* size of parameter list */
+ union {
+ struct cfe_iocb_buf buffer; /* buffer parameters */
+ struct cfe_iocb_inpstat inpstat; /* input status parameters */
+ struct cfe_iocb_envbuf envbuf; /* environment function parameters */
+ struct cfe_iocb_cpuctl cpuctl; /* CPU control parameters */
+ struct cfe_iocb_time time; /* timer parameters */
+ struct cfe_iocb_meminfo meminfo; /* memory arena info parameters */
+ struct cfe_iocb_fwinfo fwinfo; /* firmware information */
+ struct cfe_iocb_exitstat exitstat; /* Exit Status */
+ };
+};
+
+
+#include <linux/init.h>
+
+void __init cfe_setup(unsigned long fwarg0, unsigned long fwarg1,
+ unsigned long fwarg2, unsigned long fwarg3);
+
+#else /* __ASSEMBLY__ */
+
+ .macro cfe_early_init
+#ifdef CONFIG_CFE
+ jal cfe_setup
+#endif
+ .endm
+
+#endif /* __ASSEMBLY__ */
+#endif /* LINUX_CFE_PRIVATE_H_ */
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2002 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/pci.h>
+
+#include <bcmpci.h>
+#include <bcm_intr.h>
+#include <bcm_map_part.h>
+#include <6348_intr.h>
+#include <6348_map_part.h>
+
+static volatile MpiRegisters * mpi = (MpiRegisters *)(MPI_BASE);
+
+static char irq_tab_bcm96348[] __initdata = {
+ [0] = INTERRUPT_ID_MPI,
+ [1] = INTERRUPT_ID_MPI,
+#if defined(CONFIG_USB)
+ [USB_HOST_SLOT] = INTERRUPT_ID_USBH
+#endif
+};
+
+int __init pcibios_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ return irq_tab_bcm96348[slot];
+}
+
+static void bcm96348_fixup(struct pci_dev *dev)
+{
+ uint32 memaddr;
+ uint32 size;
+
+ memaddr = pci_resource_start(dev, 0);
+ size = pci_resource_len(dev, 0);
+
+ switch (PCI_SLOT(dev->devfn)) {
+ case 0:
+ // UBUS to PCI address range
+ // Memory Window 1. Mask determines which bits are decoded.
+ mpi->l2pmrange1 = ~(size-1);
+ // UBUS to PCI Memory base address. This is akin to the ChipSelect base
+ // register.
+ mpi->l2pmbase1 = memaddr & BCM_PCI_ADDR_MASK;
+ // UBUS to PCI Remap Address. Replaces the masked address bits in the
+ // range register with this setting.
+ // Also, enable direct I/O and direct Memory accesses
+ mpi->l2pmremap1 = (memaddr | MEM_WINDOW_EN);
+ break;
+
+ case 1:
+ // Memory Window 2
+ mpi->l2pmrange2 = ~(size-1);
+ // UBUS to PCI Memory base address.
+ mpi->l2pmbase2 = memaddr & BCM_PCI_ADDR_MASK;
+ // UBUS to PCI Remap Address
+ mpi->l2pmremap2 = (memaddr | MEM_WINDOW_EN);
+ break;
+
+#if defined(CONFIG_USB)
+ case USB_HOST_SLOT:
+ dev->resource[0].start = USB_HOST_BASE;
+ dev->resource[0].end = USB_HOST_BASE+USB_BAR0_MEM_SIZE-1;
+ break;
+#endif
+ }
+}
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+ return 0;
+}
+
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_ANY_ID,
+ bcm96348_fixup);
+
+/*struct pci_fixup pcibios_fixups[] = {
+ { PCI_FIXUP_FINAL, PCI_ANY_ID, PCI_ANY_ID, bcm96348_fixup },
+ {0}
+};*/
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2002 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <asm/addrspace.h>
+
+#include <bcm_intr.h>
+#include <bcm_map_part.h>
+#include <6348_intr.h>
+#include <6348_map_part.h>
+#include <bcmpci.h>
+
+#include <linux/delay.h>
+
+#if defined(CONFIG_USB)
+#if 0
+#define DPRINT(x...) printk(x)
+#else
+#define DPRINT(x...)
+#endif
+
+static int
+pci63xx_int_read(unsigned int devfn, int where, u32 * value, int size);
+static int
+pci63xx_int_write(unsigned int devfn, int where, u32 * value, int size);
+
+static bool usb_mem_size_rd = FALSE;
+static uint32 usb_mem_base = 0;
+static uint32 usb_cfg_space_cmd_reg = 0;
+#endif
+static bool pci_mem_size_rd = FALSE;
+
+static volatile MpiRegisters * mpi = (MpiRegisters *)(MPI_BASE);
+
+static void mpi_SetupPciConfigAccess(uint32 addr)
+{
+ mpi->l2pcfgctl = (DIR_CFG_SEL | DIR_CFG_USEREG | addr) & ~CONFIG_TYPE;
+}
+
+static void mpi_ClearPciConfigAccess(void)
+{
+ mpi->l2pcfgctl = 0x00000000;
+}
+
+#if defined(CONFIG_USB)
+/* --------------------------------------------------------------------------
+ Name: pci63xx_int_write
+Abstract: PCI Config write on internal device(s)
+ -------------------------------------------------------------------------- */
+static int
+pci63xx_int_write(unsigned int devfn, int where, u32 * value, int size)
+{
+ if (PCI_SLOT(devfn) != USB_HOST_SLOT) {
+ return PCIBIOS_SUCCESSFUL;
+ }
+
+ switch (size) {
+ case 1:
+ DPRINT("W => Slot: %d Where: %2X Len: %d Data: %02X\n",
+ PCI_SLOT(devfn), where, size, *value);
+ break;
+ case 2:
+ DPRINT("W => Slot: %d Where: %2X Len: %d Data: %04X\n",
+ PCI_SLOT(devfn), where, size, *value);
+ switch (where) {
+ case PCI_COMMAND:
+ usb_cfg_space_cmd_reg = *value;
+ break;
+ default:
+ break;
+ }
+ break;
+ case 4:
+ DPRINT("W => Slot: %d Where: %2X Len: %d Data: %08lX\n",
+ PCI_SLOT(devfn), where, size, *value);
+ switch (where) {
+ case PCI_BASE_ADDRESS_0:
+ if (*value == 0xffffffff) {
+ usb_mem_size_rd = TRUE;
+ } else {
+ usb_mem_base = *value;
+ }
+ break;
+ default:
+ break;
+ }
+ break;
+ default:
+ break;
+ }
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+/* --------------------------------------------------------------------------
+ Name: pci63xx_int_read
+Abstract: PCI Config read on internal device(s)
+ -------------------------------------------------------------------------- */
+static int
+pci63xx_int_read(unsigned int devfn, int where, u32 * value, int size)
+{
+ uint32 retValue = 0xFFFFFFFF;
+
+ if (PCI_SLOT(devfn) != USB_HOST_SLOT) {
+ return PCIBIOS_SUCCESSFUL;
+ }
+
+ // For now, this is specific to the USB Host controller. We can
+ // make it more general if we have to...
+ // Emulate PCI Config accesses
+ switch (where) {
+ case PCI_VENDOR_ID:
+ case PCI_DEVICE_ID:
+ retValue = PCI_VENDOR_ID_BROADCOM | 0x63000000;
+ break;
+ case PCI_COMMAND:
+ case PCI_STATUS:
+ retValue = (0x0006 << 16) | usb_cfg_space_cmd_reg;
+ break;
+ case PCI_CLASS_REVISION:
+ case PCI_CLASS_DEVICE:
+ retValue = (PCI_CLASS_SERIAL_USB << 16) | (0x10 << 8) | 0x01;
+ break;
+ case PCI_BASE_ADDRESS_0:
+ if (usb_mem_size_rd) {
+ retValue = USB_BAR0_MEM_SIZE;
+ } else {
+ if (usb_mem_base != 0)
+ retValue = usb_mem_base;
+ else
+ retValue = USB_HOST_BASE;
+ }
+ usb_mem_size_rd = FALSE;
+ break;
+ case PCI_CACHE_LINE_SIZE:
+ case PCI_LATENCY_TIMER:
+ retValue = 0;
+ break;
+ case PCI_HEADER_TYPE:
+ retValue = PCI_HEADER_TYPE_NORMAL;
+ break;
+ case PCI_SUBSYSTEM_VENDOR_ID:
+ retValue = PCI_VENDOR_ID_BROADCOM;
+ break;
+ case PCI_SUBSYSTEM_ID:
+ retValue = 0x6300;
+ break;
+ case PCI_INTERRUPT_LINE:
+ retValue = INTERRUPT_ID_USBH;
+ break;
+ default:
+ break;
+ }
+
+ switch (size) {
+ case 1:
+ *value = (retValue >> ((where & 3) << 3)) & 0xff;
+ DPRINT("R <= Slot: %d Where: %2X Len: %d Data: %02X\n",
+ PCI_SLOT(devfn), where, size, *value);
+ break;
+ case 2:
+ *value = (retValue >> ((where & 3) << 3)) & 0xffff;
+ DPRINT("R <= Slot: %d Where: %2X Len: %d Data: %04X\n",
+ PCI_SLOT(devfn), where, size, *value);
+ break;
+ case 4:
+ *value = retValue;
+ DPRINT("R <= Slot: %d Where: %2X Len: %d Data: %08lX\n",
+ PCI_SLOT(devfn), where, size, *value);
+ break;
+ default:
+ break;
+ }
+
+ return PCIBIOS_SUCCESSFUL;
+}
+#endif
+
+static int bcm96348_pcibios_read(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 * val)
+{
+ volatile unsigned char *ioBase = (unsigned char *)(mpi->l2piobase | KSEG1);
+ uint32 data;
+
+#if defined(CONFIG_USB)
+ if (PCI_SLOT(devfn) == USB_HOST_SLOT)
+ return pci63xx_int_read(devfn, where, val, size);
+#endif
+
+ mpi_SetupPciConfigAccess(BCM_PCI_CFG(PCI_SLOT(devfn), PCI_FUNC(devfn), where));
+ data = *(uint32 *)ioBase;
+ switch(size) {
+ case 1:
+ *val = (data >> ((where & 3) << 3)) & 0xff;
+ break;
+ case 2:
+ *val = (data >> ((where & 3) << 3)) & 0xffff;
+ break;
+ case 4:
+ *val = data;
+ /* Special case for reading PCI device range */
+ if ((where >= PCI_BASE_ADDRESS_0) && (where <= PCI_BASE_ADDRESS_5)) {
+ if (pci_mem_size_rd) {
+ /* bcm6348 PCI memory window minimum size is 64K */
+ *val &= PCI_SIZE_64K;
+ }
+ }
+ break;
+ default:
+ break;
+ }
+ pci_mem_size_rd = FALSE;
+ mpi_ClearPciConfigAccess();
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+static int bcm96348_pcibios_write(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 val)
+{
+ volatile unsigned char *ioBase = (unsigned char *)(mpi->l2piobase | KSEG1);
+ uint32 data;
+
+#if defined(CONFIG_USB)
+ if (PCI_SLOT(devfn) == USB_HOST_SLOT)
+ return pci63xx_int_write(devfn, where, &val, size);
+#endif
+ mpi_SetupPciConfigAccess(BCM_PCI_CFG(PCI_SLOT(devfn), PCI_FUNC(devfn), where));
+ data = *(uint32 *)ioBase;
+ switch(size) {
+ case 1:
+ data = (data & ~(0xff << ((where & 3) << 3))) |
+ (val << ((where & 3) << 3));
+ break;
+ case 2:
+ data = (data & ~(0xffff << ((where & 3) << 3))) |
+ (val << ((where & 3) << 3));
+ break;
+ case 4:
+ data = val;
+ /* Special case for reading PCI device range */
+ if ((where >= PCI_BASE_ADDRESS_0) && (where <= PCI_BASE_ADDRESS_5)) {
+ if (val == 0xffffffff)
+ pci_mem_size_rd = TRUE;
+ }
+ break;
+ default:
+ break;
+ }
+ *(uint32 *)ioBase = data;
+ udelay(500);
+ mpi_ClearPciConfigAccess();
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+struct pci_ops bcm96348_pci_ops = {
+ .read = bcm96348_pcibios_read,
+ .write = bcm96348_pcibios_write
+};
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2002 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+#include <bcmpci.h>
+
+static struct resource bcm_pci_io_resource = {
+ .name = "bcm96348 pci IO space",
+ .start = BCM_PCI_IO_BASE,
+ .end = BCM_PCI_IO_BASE + BCM_PCI_IO_SIZE_64KB - 1,
+ .flags = IORESOURCE_IO
+};
+
+static struct resource bcm_pci_mem_resource = {
+ .name = "bcm96348 pci memory space",
+ .start = BCM_PCI_MEM_BASE,
+ .end = BCM_PCI_MEM_BASE + BCM_PCI_MEM_SIZE_16MB - 1,
+ .flags = IORESOURCE_MEM
+};
+
+extern struct pci_ops bcm96348_pci_ops;
+
+struct pci_controller bcm96348_controller = {
+ .pci_ops = &bcm96348_pci_ops,
+ .io_resource = &bcm_pci_io_resource,
+ .mem_resource = &bcm_pci_mem_resource,
+};
+
+static __init int bcm96348_pci_init(void)
+{
+ /* Avoid ISA compat ranges. */
+ PCIBIOS_MIN_IO = 0x00000000;
+ PCIBIOS_MIN_MEM = 0x00000000;
+
+ /* Set I/O resource limits. */
+ ioport_resource.end = 0x1fffffff;
+ iomem_resource.end = 0xffffffff;
+
+ register_pci_controller(&bcm96348_controller);
+ return 0;
+}
+
+subsys_initcall(bcm96348_pci_init);
--- /dev/null
+/*
+ * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2005 Waldemar Brodkorb <wbx@openwrt.org>
+ * Copyright (C) 2004 Florian Schirmer (jolt@tuxbox.org)
+ *
+ * original functions for finding root filesystem from Mike Baker
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ * Copyright 2001-2003, Broadcom Corporation
+ * All Rights Reserved.
+ *
+ * THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
+ * KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
+ * SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
+ *
+ * Flash mapping for BCM963XX boards
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/wait.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#ifdef CONFIG_MTD_PARTITIONS
+#include <linux/mtd/partitions.h>
+#endif
+#include <linux/squashfs_fs.h>
+#include <linux/jffs2.h>
+#include <linux/crc32.h>
+#include <asm/io.h>
+
+#include <asm/mach-bcm963xx/bootloaders.h>
+
+extern int boot_loader_type;
+extern int parse_redboot_partitions(struct mtd_info *master, struct mtd_partition **pparts, unsigned long fis_origin);
+static struct mtd_partition *parsed_parts;
+
+
+#define TRX_MAGIC 0x30524448 /* "HDR0" */
+#define TRX_VERSION 1
+#define TRX_MAX_LEN 0x3A0000
+#define TRX_NO_HEADER 1 /* Do not write TRX header */
+#define TRX_GZ_FILES 0x2 /* Contains up to TRX_MAX_OFFSET individual gzip files */
+#define TRX_MAX_OFFSET 3
+
+struct trx_header {
+ u32 magic; /* "HDR0" */
+ u32 len; /* Length of file including header */
+ u32 crc32; /* 32-bit CRC from flag_version to end of file */
+ u32 flag_version; /* 0:15 flags, 16:31 version */
+ u32 offsets[TRX_MAX_OFFSET]; /* Offsets of partitions from start of header */
+};
+
+#define ROUNDUP(x, y) ((((x)+((y)-1))/(y))*(y))
+#define NVRAM_SPACE 0x8000
+#define WINDOW_ADDR 0x1f000000
+#define WINDOW_SIZE 0x800000
+#define BUSWIDTH 2
+
+#define EXTENDED_SIZE 0xBFC00000 /* Extended flash address */
+
+static struct mtd_info *bcm963xx_mtd;
+
+static struct map_info bcm963xx_map = {
+ .name = "Physically mapped flash",
+ .size = WINDOW_SIZE,
+ .bankwidth = BUSWIDTH,
+ .phys = WINDOW_ADDR,
+};
+
+#ifdef CONFIG_MTD_PARTITIONS
+
+static struct mtd_partition bcm963xx_parts[] = {
+ { name: "cfe", offset: 0, size: 0, mask_flags: MTD_WRITEABLE, },
+ { name: "linux", offset: 0, size: 0, },
+ { name: "rootfs", offset: 0, size: 0, },
+ { name: "nvram", offset: 0, size: 0, },
+ { name: "OpenWrt", offset: 0, size: 0, },
+ { name: NULL, },
+};
+
+static int __init
+find_cfe_size(struct mtd_info *mtd, size_t size)
+{
+ struct trx_header *trx;
+ unsigned char buf[512];
+ int off;
+ size_t len;
+ int blocksize;
+
+ trx = (struct trx_header *) buf;
+
+ blocksize = mtd->erasesize;
+ if (blocksize < 0x10000)
+ blocksize = 0x10000;
+
+ for (off = (128*1024); off < size; off += blocksize) {
+ memset(buf, 0xe5, sizeof(buf));
+
+ /*
+ * Read into buffer
+ */
+ if (mtd->read(mtd, off, sizeof(buf), &len, buf) ||
+ len != sizeof(buf))
+ continue;
+
+ /* found a TRX header */
+ if (le32_to_cpu(trx->magic) == TRX_MAGIC) {
+ goto found;
+ }
+ }
+
+ printk(KERN_NOTICE
+ "%s: Couldn't find bootloader size\n",
+ mtd->name);
+ return -1;
+
+ found:
+ printk(KERN_NOTICE "bootloader size: %d\n", off);
+ return off;
+
+}
+
+/*
+ * Copied from mtdblock.c
+ *
+ * Cache stuff...
+ *
+ * Since typical flash erasable sectors are much larger than what Linux's
+ * buffer cache can handle, we must implement read-modify-write on flash
+ * sectors for each block write requests. To avoid over-erasing flash sectors
+ * and to speed things up, we locally cache a whole flash sector while it is
+ * being written to until a different sector is required.
+ */
+
+static void erase_callback(struct erase_info *done)
+{
+ wait_queue_head_t *wait_q = (wait_queue_head_t *)done->priv;
+ wake_up(wait_q);
+}
+
+static int erase_write (struct mtd_info *mtd, unsigned long pos,
+ int len, const char *buf)
+{
+ struct erase_info erase;
+ DECLARE_WAITQUEUE(wait, current);
+ wait_queue_head_t wait_q;
+ size_t retlen;
+ int ret;
+
+ /*
+ * First, let's erase the flash block.
+ */
+
+ init_waitqueue_head(&wait_q);
+ erase.mtd = mtd;
+ erase.callback = erase_callback;
+ erase.addr = pos;
+ erase.len = len;
+ erase.priv = (u_long)&wait_q;
+
+ set_current_state(TASK_INTERRUPTIBLE);
+ add_wait_queue(&wait_q, &wait);
+
+ ret = mtd->erase(mtd, &erase);
+ if (ret) {
+ set_current_state(TASK_RUNNING);
+ remove_wait_queue(&wait_q, &wait);
+ printk (KERN_WARNING "erase of region [0x%lx, 0x%x] "
+ "on \"%s\" failed\n",
+ pos, len, mtd->name);
+ return ret;
+ }
+
+ schedule(); /* Wait for erase to finish. */
+ remove_wait_queue(&wait_q, &wait);
+
+ /*
+ * Next, writhe data to flash.
+ */
+
+ ret = mtd->write (mtd, pos, len, &retlen, buf);
+ if (ret)
+ return ret;
+ if (retlen != len)
+ return -EIO;
+ return 0;
+}
+
+
+
+
+static int __init
+find_root(struct mtd_info *mtd, size_t size, struct mtd_partition *part)
+{
+ struct trx_header trx, *trx2;
+ unsigned char buf[512], *block;
+ int off, blocksize;
+ u32 i, crc = ~0;
+ size_t len;
+ struct squashfs_super_block *sb = (struct squashfs_super_block *) buf;
+
+ blocksize = mtd->erasesize;
+ if (blocksize < 0x10000)
+ blocksize = 0x10000;
+
+ for (off = (128*1024); off < size; off += blocksize) {
+ memset(&trx, 0xe5, sizeof(trx));
+
+ /*
+ * Read into buffer
+ */
+ if (mtd->read(mtd, off, sizeof(trx), &len, (char *) &trx) ||
+ len != sizeof(trx))
+ continue;
+
+ /* found a TRX header */
+ if (le32_to_cpu(trx.magic) == TRX_MAGIC) {
+ part->offset = le32_to_cpu(trx.offsets[2]) ? :
+ le32_to_cpu(trx.offsets[1]);
+ part->size = le32_to_cpu(trx.len);
+
+ part->size -= part->offset;
+ part->offset += off;
+
+ goto found;
+ }
+ }
+
+ printk(KERN_NOTICE
+ "%s: Couldn't find root filesystem\n",
+ mtd->name);
+ return -1;
+
+ found:
+ if (part->size == 0)
+ return 0;
+
+ if (mtd->read(mtd, part->offset, sizeof(buf), &len, buf) || len != sizeof(buf))
+ return 0;
+
+ if (*((__u32 *) buf) == SQUASHFS_MAGIC) {
+ printk(KERN_INFO "%s: Filesystem type: squashfs, size=0x%x\n", mtd->name, (u32) sb->bytes_used);
+
+ /* Update the squashfs partition size based on the superblock info */
+ part->size = sb->bytes_used;
+ len = part->offset + part->size;
+ len += (mtd->erasesize - 1);
+ len &= ~(mtd->erasesize - 1);
+ part->size = len - part->offset;
+ } else if (*((__u16 *) buf) == JFFS2_MAGIC_BITMASK) {
+ printk(KERN_INFO "%s: Filesystem type: jffs2\n", mtd->name);
+
+ /* Move the squashfs outside of the trx */
+ part->size = 0;
+ } else {
+ printk(KERN_INFO "%s: Filesystem type: unknown\n", mtd->name);
+ return 0;
+ }
+
+ if (trx.len != part->offset + part->size - off) {
+ /* Update the trx offsets and length */
+ trx.len = part->offset + part->size - off;
+
+ /* Update the trx crc32 */
+ for (i = (u32) &(((struct trx_header *)NULL)->flag_version); i <= trx.len; i += sizeof(buf)) {
+ if (mtd->read(mtd, off + i, sizeof(buf), &len, buf) || len != sizeof(buf))
+ return 0;
+ crc = crc32_le(crc, buf, min(sizeof(buf), trx.len - i));
+ }
+ trx.crc32 = crc;
+
+ /* read first eraseblock from the trx */
+ block = kmalloc(mtd->erasesize, GFP_KERNEL);
+ trx2 = (struct trx_header *) block;
+ if (mtd->read(mtd, off, mtd->erasesize, &len, block) || len != mtd->erasesize) {
+ printk("Error accessing the first trx eraseblock\n");
+ return 0;
+ }
+
+ printk("Updating TRX offsets and length:\n");
+ printk("old trx = [0x%08x, 0x%08x, 0x%08x], len=0x%08x crc32=0x%08x\n", trx2->offsets[0], trx2->offsets[1], trx2->offsets[2], trx2->len, trx2->crc32);
+ printk("new trx = [0x%08x, 0x%08x, 0x%08x], len=0x%08x crc32=0x%08x\n", trx.offsets[0], trx.offsets[1], trx.offsets[2], trx.len, trx.crc32);
+
+ /* Write updated trx header to the flash */
+ memcpy(block, &trx, sizeof(trx));
+ if (mtd->unlock)
+ mtd->unlock(mtd, off, mtd->erasesize);
+ erase_write(mtd, off, mtd->erasesize, block);
+ if (mtd->sync)
+ mtd->sync(mtd);
+ kfree(block);
+ printk("Done\n");
+ }
+
+ return part->size;
+}
+
+struct mtd_partition * __init
+init_mtd_partitions(struct mtd_info *mtd, size_t size)
+{
+ int cfe_size;
+
+ if ((cfe_size = find_cfe_size(mtd,size)) < 0)
+ return NULL;
+
+ /* boot loader */
+ bcm963xx_parts[0].offset = 0;
+ bcm963xx_parts[0].size = cfe_size;
+
+ /* nvram */
+ if (cfe_size != 384 * 1024) {
+ bcm963xx_parts[3].offset = size - ROUNDUP(NVRAM_SPACE, mtd->erasesize);
+ bcm963xx_parts[3].size = ROUNDUP(NVRAM_SPACE, mtd->erasesize);
+ } else {
+ /* nvram (old 128kb config partition on netgear wgt634u) */
+ bcm963xx_parts[3].offset = bcm963xx_parts[0].size;
+ bcm963xx_parts[3].size = ROUNDUP(NVRAM_SPACE, mtd->erasesize);
+ }
+
+ /* linux (kernel and rootfs) */
+ if (cfe_size != 384 * 1024) {
+ bcm963xx_parts[1].offset = bcm963xx_parts[0].size;
+ bcm963xx_parts[1].size = bcm963xx_parts[3].offset -
+ bcm963xx_parts[1].offset;
+ } else {
+ /* do not count the elf loader, which is on one block */
+ bcm963xx_parts[1].offset = bcm963xx_parts[0].size +
+ bcm963xx_parts[3].size + mtd->erasesize;
+ bcm963xx_parts[1].size = size -
+ bcm963xx_parts[0].size -
+ (2*bcm963xx_parts[3].size) -
+ mtd->erasesize;
+ }
+
+ /* find and size rootfs */
+ if (find_root(mtd,size,&bcm963xx_parts[2])==0) {
+ /* entirely jffs2 */
+ bcm963xx_parts[4].name = NULL;
+ bcm963xx_parts[2].size = size - bcm963xx_parts[2].offset -
+ bcm963xx_parts[3].size;
+ } else {
+ /* legacy setup */
+ /* calculate leftover flash, and assign it to the jffs2 partition */
+ if (cfe_size != 384 * 1024) {
+ bcm963xx_parts[4].offset = bcm963xx_parts[2].offset +
+ bcm963xx_parts[2].size;
+ if ((bcm963xx_parts[4].offset % mtd->erasesize) > 0) {
+ bcm963xx_parts[4].offset += mtd->erasesize -
+ (bcm963xx_parts[4].offset % mtd->erasesize);
+ }
+ bcm963xx_parts[4].size = bcm963xx_parts[3].offset -
+ bcm963xx_parts[4].offset;
+ } else {
+ bcm963xx_parts[4].offset = bcm963xx_parts[2].offset +
+ bcm963xx_parts[2].size;
+ if ((bcm963xx_parts[4].offset % mtd->erasesize) > 0) {
+ bcm963xx_parts[4].offset += mtd->erasesize -
+ (bcm963xx_parts[4].offset % mtd->erasesize);
+ }
+ bcm963xx_parts[4].size = size - bcm963xx_parts[3].size -
+ bcm963xx_parts[4].offset;
+ }
+ }
+
+ return bcm963xx_parts;
+}
+#endif
+
+int __init init_bcm963xx_map(void)
+{
+ size_t size;
+ int ret = 0;
+ struct mtd_partition *parts;
+ int i;
+
+ printk("BCM963xx flash init: 0x%08x 0x%08x\n", WINDOW_ADDR, WINDOW_SIZE);
+ bcm963xx_map.virt = ioremap_nocache(WINDOW_ADDR, WINDOW_SIZE);
+
+ if (!bcm963xx_map.virt) {
+ printk("Failed to ioremap\n");
+ return -EIO;
+ }
+
+ simple_map_init(&bcm963xx_map);
+
+ if (!(bcm963xx_mtd = do_map_probe("jedec_probe", &bcm963xx_map))) {
+ printk("Failed to jedec_probe\n");
+ iounmap((void *)bcm963xx_map.virt);
+ return -ENXIO;
+ }
+
+ bcm963xx_mtd->owner = THIS_MODULE;
+
+ size = bcm963xx_mtd->size;
+
+ printk(KERN_NOTICE "Flash device: 0x%x at 0x%x\n", size, WINDOW_ADDR);
+
+ if (boot_loader_type == BOOT_LOADER_REDBOOT) {
+ int parsed_nr_parts = 0;
+ char * part_type;
+
+ if (bcm963xx_mtd->size > 0x00400000) {
+ printk("Support for extended flash memory size : 0x%08X ; ONLY 64MBIT SUPPORT\n", bcm963xx_mtd->size);
+ bcm963xx_map.virt = (unsigned long)EXTENDED_SIZE;
+ }
+
+ if (parsed_nr_parts == 0) {
+ int ret = parse_redboot_partitions(bcm963xx_mtd, &parsed_parts, 0);
+ if (ret > 0) {
+ part_type = "RedBoot";
+ parsed_nr_parts = ret;
+ }
+ }
+ add_mtd_partitions(bcm963xx_mtd, parsed_parts, parsed_nr_parts);
+ }
+ else {
+ parts = init_mtd_partitions(bcm963xx_mtd, size);
+ for (i = 0; parts[i].name; i++);
+ ret = add_mtd_partitions(bcm963xx_mtd, parts, i);
+ if (ret) {
+ printk(KERN_ERR "Flash: add_mtd_partitions failed\n");
+ goto fail;
+ }
+ }
+ return 0;
+
+ fail:
+ if (bcm963xx_mtd)
+ map_destroy(bcm963xx_mtd);
+ if (bcm963xx_map.virt)
+ iounmap((void *)bcm963xx_map.virt);
+ bcm963xx_map.virt = 0;
+ return ret;
+}
+
+void __exit cleanup_bcm963xx_map(void)
+{
+ del_mtd_partitions(bcm963xx_mtd);
+ map_destroy(bcm963xx_mtd);
+ iounmap((void *)bcm963xx_map.virt);
+}
+
+module_init(init_bcm963xx_map);
+module_exit(cleanup_bcm963xx_map);
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2002 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+
+/* Description: Serial port driver for the BCM963XX. */
+
+#define CARDNAME "bcm963xx_serial driver"
+#define VERSION "2.0"
+#define VER_STR CARDNAME " v" VERSION "\n"
+
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+
+/* for definition of struct console */
+#include <linux/console.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial.h>
+#include <linux/serialP.h>
+#include <asm/uaccess.h>
+
+#include <bcmtypes.h>
+#include <board.h>
+#include <bcm_map_part.h>
+#include <bcm_intr.h>
+#include <6348_map_part.h>
+#include <6348_intr.h>
+
+static DEFINE_SPINLOCK(bcm963xx_serial_lock);
+
+extern void _putc(char);
+extern void _puts(const char *);
+
+typedef struct bcm_serial {
+ volatile Uart *port;
+ int type;
+ int flags;
+ int irq;
+ int baud_base;
+ int blocked_open;
+ unsigned short close_delay;
+ unsigned short closing_wait;
+ unsigned short line; /* port/line number */
+ unsigned short cflags; /* line configuration flag */
+ unsigned short x_char; /* xon/xoff character */
+ unsigned short read_status_mask; /* mask for read condition */
+ unsigned short ignore_status_mask; /* mask for ignore condition */
+ unsigned long event; /* mask used in BH */
+ int xmit_head; /* Position of the head */
+ int xmit_tail; /* Position of the tail */
+ int xmit_cnt; /* Count of the chars in the buffer */
+ int count; /* indicates how many times it has been opened */
+ int magic;
+
+ struct async_icount icount; /* keep track of things ... */
+ struct tty_struct *tty; /* tty associated */
+ struct termios normal_termios;
+
+ wait_queue_head_t open_wait;
+ wait_queue_head_t close_wait;
+
+ long session; /* Session of opening process */
+ long pgrp; /* pgrp of opening process */
+
+ unsigned char is_initialized;
+} Context;
+
+
+/*---------------------------------------------------------------------*/
+/* Define bits in the Interrupt Enable register */
+/*---------------------------------------------------------------------*/
+/* Enable receive interrupt */
+#define RXINT (RXFIFONE|RXOVFERR)
+
+/* Enable transmit interrupt */
+#define TXINT (TXFIFOEMT|TXUNDERR|TXOVFERR)
+
+/* Enable receiver line status interrupt */
+#define LSINT (RXBRK|RXPARERR|RXFRAMERR)
+
+#define BCM_NUM_UARTS 1
+
+#define BD_BCM63XX_TIMER_CLOCK_INPUT (FPERIPH)
+
+
+static struct bcm_serial multi[BCM_NUM_UARTS];
+static struct bcm_serial *lines[BCM_NUM_UARTS];
+static struct tty_driver *serial_driver;
+static struct termios *serial_termios[BCM_NUM_UARTS];
+static struct termios *serial_termios_locked[BCM_NUM_UARTS];
+
+
+static void bcm_stop(struct tty_struct *tty);
+static void bcm_start(struct tty_struct *tty);
+static inline void receive_chars(struct bcm_serial *info);
+static int startup(struct bcm_serial *info);
+static void shutdown(struct bcm_serial *info);
+static void change_speed(volatile Uart * pUart, tcflag_t cFlag);
+static void bcm63xx_cons_flush_chars(struct tty_struct *tty);
+static int bcm63xx_cons_write(struct tty_struct *tty,
+ const unsigned char *buf, int count);
+static int bcm63xx_cons_write_room(struct tty_struct *tty);
+static int bcm_chars_in_buffer(struct tty_struct *tty);
+static void bcm_flush_buffer(struct tty_struct *tty);
+static void bcm_throttle(struct tty_struct *tty);
+static void bcm_unthrottle(struct tty_struct *tty);
+static void bcm_send_xchar(struct tty_struct *tty, char ch);
+static int get_serial_info(struct bcm_serial *info,
+ struct serial_struct *retinfo);
+static int set_serial_info(struct bcm_serial *info,
+ struct serial_struct *new_info);
+static int get_lsr_info(struct bcm_serial *info, unsigned int *value);
+static void send_break(struct bcm_serial *info, int duration);
+static int bcm_ioctl(struct tty_struct *tty, struct file *file,
+ unsigned int cmd, unsigned long arg);
+static void bcm_set_termios(struct tty_struct *tty,
+ struct termios *old_termios);
+static void bcm63xx_cons_close(struct tty_struct *tty, struct file *filp);
+static void bcm_hangup(struct tty_struct *tty);
+static int block_til_ready(struct tty_struct *tty, struct file *filp,
+ struct bcm_serial *info);
+static int bcm63xx_cons_open(struct tty_struct *tty, struct file *filp);
+static int __init bcm63xx_serialinit(void);
+
+
+/*
+ * ------------------------------------------------------------
+ * rs_stop () and rs_start ()
+ *
+ * These routines are called before setting or resetting
+ * tty->stopped. They enable or disable transmitter interrupts,
+ * as necessary.
+ * ------------------------------------------------------------
+ */
+static void bcm_stop(struct tty_struct *tty)
+{
+}
+
+static void bcm_start(struct tty_struct *tty)
+{
+ _puts(CARDNAME " Start\n");
+}
+
+/*
+ * ------------------------------------------------------------
+ * receive_char ()
+ *
+ * This routine deals with inputs from any lines.
+ * ------------------------------------------------------------
+ */
+static inline void receive_chars(struct bcm_serial *info)
+{
+ struct tty_struct *tty = 0;
+ struct async_icount *icount;
+ int ignore = 0;
+ unsigned short status, tmp;
+ UCHAR ch = 0;
+ while ((status = info->port->intStatus) & RXINT) {
+ char flag_char = TTY_NORMAL;
+
+ if (status & RXFIFONE)
+ ch = info->port->Data; // Read the character
+ tty = info->tty; /* now tty points to the proper dev */
+ icount = &info->icount;
+ if (!tty)
+ break;
+ if (!tty_buffer_request_room(tty, 1))
+ break;
+ icount->rx++;
+ if (status & RXBRK) {
+ flag_char = TTY_BREAK;
+ icount->brk++;
+ }
+ // keep track of the statistics
+ if (status & (RXFRAMERR | RXPARERR | RXOVFERR)) {
+ if (status & RXPARERR) /* parity error */
+ icount->parity++;
+ else if (status & RXFRAMERR) /* frame error */
+ icount->frame++;
+ if (status & RXOVFERR) {
+ // Overflow. Reset the RX FIFO
+ info->port->fifoctl |= RSTRXFIFOS;
+ icount->overrun++;
+ }
+ // check to see if we should ignore the character
+ // and mask off conditions that should be ignored
+ if (status & info->ignore_status_mask) {
+ if (++ignore > 100)
+ break;
+ goto ignore_char;
+ }
+ // Mask off the error conditions we want to ignore
+ tmp = status & info->read_status_mask;
+ if (tmp & RXPARERR) {
+ flag_char = TTY_PARITY;
+ } else if (tmp & RXFRAMERR) {
+ flag_char = TTY_FRAME;
+ }
+ if (tmp & RXOVFERR) {
+ tty_insert_flip_char(tty, ch, flag_char);
+ ch = 0;
+ flag_char = TTY_OVERRUN;
+ if (!tty_buffer_request_room(tty, 1))
+ break;
+ }
+ }
+ tty_insert_flip_char(tty, ch, flag_char);
+ }
+ ignore_char:;
+ tty_flip_buffer_push(tty);
+ tty_schedule_flip(tty);
+
+}
+
+
+/*
+ * ------------------------------------------------------------
+ * bcm_interrupt ()
+ *
+ * this is the main interrupt routine for the chip.
+ * It deals with the multiple ports.
+ * ------------------------------------------------------------
+ */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
+static irqreturn_t bcm_interrupt(int irq, void *dev)
+#else
+static void bcm_interrupt(int irq, void *dev, struct pt_regs *regs)
+#endif
+{
+ struct bcm_serial *info = lines[0];
+ UINT16 intStat;
+
+ /* get pending interrupt flags from UART */
+
+ /* Mask with only the serial interrupts that are enabled */
+ intStat = info->port->intStatus & info->port->intMask;
+ while (intStat) {
+ if (intStat & RXINT)
+ receive_chars(info);
+ else if (intStat & TXINT)
+ info->port->intStatus = TXINT;
+ else /* don't know what it was, so let's mask it */
+ info->port->intMask &= ~intStat;
+
+ intStat = info->port->intStatus & info->port->intMask;
+ }
+
+ // Clear the interrupt
+ enable_brcm_irq(INTERRUPT_ID_UART);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
+ return IRQ_HANDLED;
+#endif
+}
+
+/*
+ * -------------------------------------------------------------------
+ * startup ()
+ *
+ * various initialization tasks
+ * -------------------------------------------------------------------
+ */
+static int startup(struct bcm_serial *info)
+{
+ // Port is already started...
+ return 0;
+}
+
+/*
+ * -------------------------------------------------------------------
+ * shutdown ()
+ *
+ * This routine will shutdown a serial port; interrupts are disabled, and
+ * DTR is dropped if the hangup on close termio flag is on.
+ * -------------------------------------------------------------------
+ */
+static void shutdown(struct bcm_serial *info)
+{
+ unsigned long flags;
+ if (!info->is_initialized)
+ return;
+
+ spin_lock_irqsave(&bcm963xx_serial_lock, flags);
+
+ info->port->control &= ~(BRGEN | TXEN | RXEN);
+ if (info->tty)
+ set_bit(TTY_IO_ERROR, &info->tty->flags);
+ info->is_initialized = 0;
+
+ spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
+}
+
+/*
+ * -------------------------------------------------------------------
+ * change_speed ()
+ *
+ * Set the baud rate, character size, parity and stop bits.
+ * -------------------------------------------------------------------
+ */
+static void change_speed(volatile Uart * pUart, tcflag_t cFlag)
+{
+ unsigned long ulFlags, ulBaud, ulClockFreqHz, ulTmp;
+
+ spin_lock_irqsave(&bcm963xx_serial_lock, ulFlags);
+ switch (cFlag & (CBAUD | CBAUDEX)) {
+ case B115200:
+ ulBaud = 115200;
+ break;
+ case B57600:
+ ulBaud = 57600;
+ break;
+ case B38400:
+ ulBaud = 38400;
+ break;
+ case B19200:
+ ulBaud = 19200;
+ break;
+ case B9600:
+ ulBaud = 9600;
+ break;
+ case B4800:
+ ulBaud = 4800;
+ break;
+ case B2400:
+ ulBaud = 2400;
+ break;
+ case B1800:
+ ulBaud = 1800;
+ break;
+ case B1200:
+ ulBaud = 1200;
+ break;
+ case B600:
+ ulBaud = 600;
+ break;
+ case B300:
+ ulBaud = 300;
+ break;
+ case B200:
+ ulBaud = 200;
+ break;
+ case B150:
+ ulBaud = 150;
+ break;
+ case B134:
+ ulBaud = 134;
+ break;
+ case B110:
+ ulBaud = 110;
+ break;
+ case B75:
+ ulBaud = 75;
+ break;
+ case B50:
+ ulBaud = 50;
+ break;
+ default:
+ ulBaud = 115200;
+ break;
+ }
+
+ /* Calculate buad rate. */
+ ulClockFreqHz = BD_BCM63XX_TIMER_CLOCK_INPUT;
+ ulTmp = (ulClockFreqHz / ulBaud) / 16;
+ if (ulTmp & 0x01)
+ ulTmp /= 2; /* Rounding up, so sub is already accounted for */
+ else
+ ulTmp = (ulTmp / 2) - 1; /* Rounding down so we must sub 1 */
+ pUart->baudword = ulTmp;
+
+ /* Set character size, stop bits and parity. */
+ switch (cFlag & CSIZE) {
+ case CS5:
+ ulTmp = BITS5SYM; /* select transmit 5 bit data size */
+ break;
+ case CS6:
+ ulTmp = BITS6SYM; /* select transmit 6 bit data size */
+ break;
+ case CS7:
+ ulTmp = BITS7SYM; /* select transmit 7 bit data size */
+ break;
+ default:
+ ulTmp = BITS8SYM; /* select transmit 8 bit data size */
+ break;
+ }
+ if (cFlag & CSTOPB)
+ ulTmp |= TWOSTOP; /* select 2 stop bits */
+ else
+ ulTmp |= ONESTOP; /* select one stop bit */
+
+ /* Write these values into the config reg. */
+ pUart->config = ulTmp;
+ pUart->control &=
+ ~(RXPARITYEN | TXPARITYEN | RXPARITYEVEN | TXPARITYEVEN);
+ switch (cFlag & (PARENB | PARODD)) {
+ case PARENB | PARODD:
+ pUart->control |= RXPARITYEN | TXPARITYEN;
+ break;
+ case PARENB:
+ pUart->control |=
+ RXPARITYEN | TXPARITYEN | RXPARITYEVEN | TXPARITYEVEN;
+ break;
+ default:
+ pUart->control |= 0;
+ break;
+ }
+
+ /* Reset and flush uart */
+ pUart->fifoctl = RSTTXFIFOS | RSTRXFIFOS;
+ spin_unlock_irqrestore(&bcm963xx_serial_lock, ulFlags);
+}
+
+
+/*
+ * -------------------------------------------------------------------
+ * bcm_flush_char ()
+ *
+ * Nothing to flush. Polled I/O is used.
+ * -------------------------------------------------------------------
+ */
+static void bcm63xx_cons_flush_chars(struct tty_struct *tty)
+{
+}
+
+
+/*
+ * -------------------------------------------------------------------
+ * bcm63xx_cons_write ()
+ *
+ * Main output routine using polled I/O.
+ * -------------------------------------------------------------------
+ */
+static int bcm63xx_cons_write(struct tty_struct *tty,
+ const unsigned char *buf, int count)
+{
+ int c;
+
+ for (c = 0; c < count; c++)
+ _putc(buf[c]);
+ return count;
+}
+
+/*
+ * -------------------------------------------------------------------
+ * bcm63xx_cons_write_room ()
+ *
+ * Compute the amount of space available for writing.
+ * -------------------------------------------------------------------
+ */
+static int bcm63xx_cons_write_room(struct tty_struct *tty)
+{
+ /* Pick a number. Any number. Polled I/O is used. */
+ return 1024;
+}
+
+/*
+ * -------------------------------------------------------------------
+ * bcm_chars_in_buffer ()
+ *
+ * compute the amount of char left to be transmitted
+ * -------------------------------------------------------------------
+ */
+static int bcm_chars_in_buffer(struct tty_struct *tty)
+{
+ return 0;
+}
+
+/*
+ * -------------------------------------------------------------------
+ * bcm_flush_buffer ()
+ *
+ * Empty the output buffer
+ * -------------------------------------------------------------------
+ */
+static void bcm_flush_buffer(struct tty_struct *tty)
+{
+ tty_wakeup(tty);
+}
+
+/*
+ * ------------------------------------------------------------
+ * bcm_throttle () and bcm_unthrottle ()
+ *
+ * This routine is called by the upper-layer tty layer to signal that
+ * incoming characters should be throttled (or not).
+ * ------------------------------------------------------------
+ */
+static void bcm_throttle(struct tty_struct *tty)
+{
+ struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
+ if (I_IXOFF(tty))
+ info->x_char = STOP_CHAR(tty);
+}
+
+static void bcm_unthrottle(struct tty_struct *tty)
+{
+ struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
+ if (I_IXOFF(tty)) {
+ if (info->x_char)
+ info->x_char = 0;
+ else
+ info->x_char = START_CHAR(tty);
+ }
+}
+
+static void bcm_send_xchar(struct tty_struct *tty, char ch)
+{
+ struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
+ info->x_char = ch;
+ if (ch)
+ bcm_start(info->tty);
+}
+
+/*
+ * ------------------------------------------------------------
+ * rs_ioctl () and friends
+ * ------------------------------------------------------------
+ */
+static int get_serial_info(struct bcm_serial *info,
+ struct serial_struct *retinfo)
+{
+ struct serial_struct tmp;
+
+ if (!retinfo)
+ return -EFAULT;
+
+ memset(&tmp, 0, sizeof(tmp));
+ tmp.type = info->type;
+ tmp.line = info->line;
+ tmp.port = (int) info->port;
+ tmp.irq = info->irq;
+ tmp.flags = 0;
+ tmp.baud_base = info->baud_base;
+ tmp.close_delay = info->close_delay;
+ tmp.closing_wait = info->closing_wait;
+
+ return copy_to_user(retinfo, &tmp, sizeof(*retinfo));
+}
+
+static int set_serial_info(struct bcm_serial *info,
+ struct serial_struct *new_info)
+{
+ struct serial_struct new_serial;
+ struct bcm_serial old_info;
+ int retval = 0;
+
+ if (!new_info)
+ return -EFAULT;
+
+ copy_from_user(&new_serial, new_info, sizeof(new_serial));
+ old_info = *info;
+
+ if (!capable(CAP_SYS_ADMIN))
+ return -EPERM;
+
+
+ if (info->count > 1)
+ return -EBUSY;
+
+ /* OK, past this point, all the error checking has been done.
+ * At this point, we start making changes.....
+ */
+ info->baud_base = new_serial.baud_base;
+ info->type = new_serial.type;
+ info->close_delay = new_serial.close_delay;
+ info->closing_wait = new_serial.closing_wait;
+ retval = startup(info);
+ return retval;
+}
+
+/*
+ * get_lsr_info - get line status register info
+ *
+ * Purpose: Let user call ioctl() to get info when the UART physically
+ * is emptied. On bus types like RS485, the transmitter must
+ * release the bus after transmitting. This must be done when
+ * the transmit shift register is empty, not be done when the
+ * transmit holding register is empty. This functionality
+ * allows an RS485 driver to be written in user space.
+ */
+static int get_lsr_info(struct bcm_serial *info, unsigned int *value)
+{
+ return (0);
+}
+
+/*
+ * This routine sends a break character out the serial port.
+ */
+static void send_break(struct bcm_serial *info, int duration)
+{
+ unsigned long flags;
+
+ if (!info->port)
+ return;
+
+ current->state = TASK_INTERRUPTIBLE;
+
+ /*save_flags (flags);
+ cli(); */
+ spin_lock_irqsave(&bcm963xx_serial_lock, flags);
+
+ info->port->control |= XMITBREAK;
+ schedule_timeout(duration);
+ info->port->control &= ~XMITBREAK;
+
+ spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
+ //restore_flags (flags);
+}
+
+static int bcm_ioctl(struct tty_struct *tty, struct file *file,
+ unsigned int cmd, unsigned long arg)
+{
+ int error;
+ struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
+ int retval;
+
+ if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
+ (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD) &&
+ (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT)) {
+ if (tty->flags & (1 << TTY_IO_ERROR))
+ return -EIO;
+ }
+ switch (cmd) {
+
+ case TCSBRK: /* SVID version: non-zero arg --> no break */
+ retval = tty_check_change(tty);
+ if (retval)
+ return retval;
+ tty_wait_until_sent(tty, 0);
+ if (!arg)
+ send_break(info, HZ / 4); /* 1/4 second */
+ return 0;
+
+ case TCSBRKP: /* support for POSIX tcsendbreak() */
+ retval = tty_check_change(tty);
+ if (retval)
+ return retval;
+ tty_wait_until_sent(tty, 0);
+ send_break(info, arg ? arg * (HZ / 10) : HZ / 4);
+ return 0;
+
+ case TIOCGSOFTCAR:
+ error =
+ access_ok(VERIFY_WRITE, (void *) arg, sizeof(long));
+ if (!error)
+ return -EFAULT;
+ else {
+ put_user(C_CLOCAL(tty) ? 1 : 0,
+ (unsigned long *) arg);
+ return 0;
+ }
+
+ case TIOCSSOFTCAR:
+ error = get_user(arg, (unsigned long *) arg);
+ if (error)
+ return error;
+ tty->termios->c_cflag =
+ ((tty->termios->
+ c_cflag & ~CLOCAL) | (arg ? CLOCAL : 0));
+ return 0;
+
+ case TIOCGSERIAL:
+ error =
+ access_ok(VERIFY_WRITE, (void *) arg,
+ sizeof(struct serial_struct));
+ if (!error)
+ return -EFAULT;
+ else
+ return get_serial_info(info,
+ (struct serial_struct *)
+ arg);
+
+ case TIOCSSERIAL:
+ return set_serial_info(info, (struct serial_struct *) arg);
+
+ case TIOCSERGETLSR: /* Get line status register */
+ error =
+ access_ok(VERIFY_WRITE, (void *) arg,
+ sizeof(unsigned int));
+ if (!error)
+ return -EFAULT;
+ else
+ return get_lsr_info(info, (unsigned int *) arg);
+
+ case TIOCSERGSTRUCT:
+ error =
+ access_ok(VERIFY_WRITE, (void *) arg,
+ sizeof(struct bcm_serial));
+ if (!error)
+ return -EFAULT;
+ else {
+ copy_to_user((struct bcm_serial *) arg, info,
+ sizeof(struct bcm_serial));
+ return 0;
+ }
+
+ default:
+ return -ENOIOCTLCMD;
+ }
+ return 0;
+}
+
+static void bcm_set_termios(struct tty_struct *tty,
+ struct termios *old_termios)
+{
+ struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
+
+ if (tty->termios->c_cflag != old_termios->c_cflag)
+ change_speed(info->port, tty->termios->c_cflag);
+}
+
+/*
+ * ------------------------------------------------------------
+ * bcm63xx_cons_close()
+ *
+ * This routine is called when the serial port gets closed. First, we
+ * wait for the last remaining data to be sent. Then, we turn off
+ * the transmit enable and receive enable flags.
+ * ------------------------------------------------------------
+ */
+static void bcm63xx_cons_close(struct tty_struct *tty, struct file *filp)
+{
+ struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
+ unsigned long flags;
+
+ if (!info)
+ return;
+
+ /*save_flags (flags);
+ cli(); */
+ spin_lock_irqsave(&bcm963xx_serial_lock, flags);
+
+ if (tty_hung_up_p(filp)) {
+ spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
+ //restore_flags (flags);
+ return;
+ }
+
+ if ((tty->count == 1) && (info->count != 1)) {
+
+ /* Uh, oh. tty->count is 1, which means that the tty
+ * structure will be freed. Info->count should always
+ * be one in these conditions. If it's greater than
+ * one, we've got real problems, since it means the
+ * serial port won't be shutdown.
+ */
+ printk
+ ("bcm63xx_cons_close: bad serial port count; tty->count is 1, "
+ "info->count is %d\n", info->count);
+ info->count = 1;
+ }
+
+ if (--info->count < 0) {
+ printk("ds_close: bad serial port count for ttys%d: %d\n",
+ info->line, info->count);
+ info->count = 0;
+ }
+
+ if (info->count) {
+ //restore_flags (flags);
+ spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
+ return;
+ }
+
+ /* Now we wait for the transmit buffer to clear; and we notify
+ * the line discipline to only process XON/XOFF characters.
+ */
+ tty->closing = 1;
+
+ /* At this point we stop accepting input. To do this, we
+ * disable the receive line status interrupts.
+ */
+ shutdown(info);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
+ if (tty->driver->flush_buffer)
+ tty->driver->flush_buffer(tty);
+#else
+ if (tty->driver.flush_buffer)
+ tty->driver.flush_buffer(tty);
+#endif
+ if (tty->ldisc.flush_buffer)
+ tty->ldisc.flush_buffer(tty);
+
+ tty->closing = 0;
+ info->event = 0;
+ info->tty = 0;
+ if (tty->ldisc.num != tty_ldisc_get(N_TTY)->num) {
+ if (tty->ldisc.close)
+ (tty->ldisc.close) (tty);
+ tty->ldisc = *tty_ldisc_get(N_TTY);
+ tty->termios->c_line = N_TTY;
+ if (tty->ldisc.open)
+ (tty->ldisc.open) (tty);
+ }
+ if (info->blocked_open) {
+ if (info->close_delay) {
+ current->state = TASK_INTERRUPTIBLE;
+ schedule_timeout(info->close_delay);
+ }
+ wake_up_interruptible(&info->open_wait);
+ }
+ wake_up_interruptible(&info->close_wait);
+
+ //restore_flags (flags);
+ spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
+}
+
+/*
+ * bcm_hangup () --- called by tty_hangup() when a hangup is signaled.
+ */
+static void bcm_hangup(struct tty_struct *tty)
+{
+
+ struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
+
+ shutdown(info);
+ info->event = 0;
+ info->count = 0;
+ info->tty = 0;
+ wake_up_interruptible(&info->open_wait);
+}
+
+/*
+ * ------------------------------------------------------------
+ * rs_open() and friends
+ * ------------------------------------------------------------
+ */
+static int block_til_ready(struct tty_struct *tty, struct file *filp,
+ struct bcm_serial *info)
+{
+ return 0;
+}
+
+/*
+ * This routine is called whenever a serial port is opened. It
+ * enables interrupts for a serial port. It also performs the
+ * serial-specific initialization for the tty structure.
+ */
+static int bcm63xx_cons_open(struct tty_struct *tty, struct file *filp)
+{
+ struct bcm_serial *info;
+ int retval, line;
+
+ // Make sure we're only opening on of the ports we support
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
+ line = MINOR(tty->driver->cdev.dev) - tty->driver->minor_start;
+#else
+ line = MINOR(tty->device) - tty->driver.minor_start;
+#endif
+
+ if ((line < 0) || (line >= BCM_NUM_UARTS))
+ return -ENODEV;
+
+ info = lines[line];
+
+ tty->low_latency = 1;
+ info->port->intMask = 0; /* Clear any pending interrupts */
+ info->port->intMask = RXINT; /* Enable RX */
+
+ info->count++;
+ tty->driver_data = info;
+ info->tty = tty;
+ enable_brcm_irq(INTERRUPT_ID_UART);
+
+ // Start up serial port
+ retval = startup(info);
+ if (retval)
+ return retval;
+
+ retval = block_til_ready(tty, filp, info);
+ if (retval)
+ return retval;
+
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
+ info->pgrp = process_group(current);
+ info->session = current->signal->session;
+#else
+ info->session = current->session;
+ info->pgrp = current->pgrp;
+#endif
+
+ return 0;
+}
+
+
+static struct tty_operations rs_ops = {
+ .open = bcm63xx_cons_open,
+ .close = bcm63xx_cons_close,
+ .write = bcm63xx_cons_write,
+ .flush_chars = bcm63xx_cons_flush_chars,
+ .write_room = bcm63xx_cons_write_room,
+ .chars_in_buffer = bcm_chars_in_buffer,
+ .flush_buffer = bcm_flush_buffer,
+ .ioctl = bcm_ioctl,
+ .throttle = bcm_throttle,
+ .unthrottle = bcm_unthrottle,
+ .send_xchar = bcm_send_xchar,
+ .set_termios = bcm_set_termios,
+ .stop = bcm_stop,
+ .start = bcm_start,
+ .hangup = bcm_hangup,
+};
+
+/* --------------------------------------------------------------------------
+ Name: bcm63xx_serialinit
+ Purpose: Initialize our BCM63xx serial driver
+-------------------------------------------------------------------------- */
+static int __init bcm63xx_serialinit(void)
+{
+ int i, flags;
+ struct bcm_serial *info;
+
+ // Print the driver version information
+ printk(VER_STR);
+ serial_driver = alloc_tty_driver(BCM_NUM_UARTS);
+ if (!serial_driver)
+ return -ENOMEM;
+
+ serial_driver->owner = THIS_MODULE;
+ serial_driver->name = "ttyS";
+ serial_driver->major = TTY_MAJOR;
+ serial_driver->minor_start = 64;
+ serial_driver->num = 1;
+ serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
+ serial_driver->subtype = SERIAL_TYPE_NORMAL;
+ serial_driver->init_termios = tty_std_termios;
+ serial_driver->init_termios.c_cflag = B115200 | CS8 | CREAD | HUPCL | CLOCAL;
+ serial_driver->flags = TTY_DRIVER_REAL_RAW;
+
+ serial_driver->termios = serial_termios;
+ serial_driver->termios_locked = serial_termios_locked;
+
+ tty_set_operations(serial_driver, &rs_ops);
+
+ if (tty_register_driver(serial_driver))
+ panic("Couldn't register serial driver\n");
+
+ //save_flags(flags); cli();
+ spin_lock_irqsave(&bcm963xx_serial_lock, flags);
+
+ for (i = 0; i < 1; i++) {
+ info = &multi[i];
+ lines[i] = info;
+ info->magic = SERIAL_MAGIC;
+ info->port = (Uart *) ((char *) UART_BASE + (i * 0x20));
+ info->tty = 0;
+ info->irq = (2 - i) + 8;
+ info->line = i;
+ info->close_delay = 50;
+ info->closing_wait = 3000;
+ info->x_char = 0;
+ info->event = 0;
+ info->count = 0;
+ info->blocked_open = 0;
+ info->normal_termios = serial_driver->init_termios;
+ init_waitqueue_head(&info->open_wait);
+ init_waitqueue_head(&info->close_wait);
+
+ /* If we are pointing to address zero then punt - not correctly
+ * set up in setup.c to handle this.
+ */
+ if (!info->port)
+ return 0;
+ BcmHalMapInterrupt(bcm_interrupt, 0, INTERRUPT_ID_UART);
+ }
+
+ /* order matters here... the trick is that flags
+ * is updated... in request_irq - to immediatedly obliterate
+ * it is unwise.
+ */
+ spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
+ return 0;
+}
+
+module_init(bcm63xx_serialinit);
+
+/* --------------------------------------------------------------------------
+ Name: bcm_console_print
+ Purpose: bcm_console_print is registered for printk.
+ The console_lock must be held when we get here.
+-------------------------------------------------------------------------- */
+static void bcm_console_print(struct console *cons, const char *str,
+ unsigned int count)
+{
+ unsigned int i;
+ //_puts(str);
+ for (i = 0; i < count; i++, str++) {
+ _putc(*str);
+ if (*str == 10) {
+ _putc(13);
+ }
+ }
+}
+
+static struct tty_driver *bcm_console_device(struct console *c, int *index)
+{
+ *index = c->index;
+ return serial_driver;
+}
+
+static int __init bcm_console_setup(struct console *co, char *options)
+{
+ return 0;
+}
+
+static struct console bcm_sercons = {
+ .name = "ttyS",
+ .write = bcm_console_print,
+ .device = bcm_console_device,
+ .setup = bcm_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+};
+
+static int __init bcm63xx_console_init(void)
+{
+ register_console(&bcm_sercons);
+ return 0;
+}
+
+console_initcall(bcm63xx_console_init);
--- /dev/null
+/*
+ * Broadcom Common Firmware Environment (CFE) support
+ *
+ * Copyright 2000, 2001, 2002
+ * Broadcom Corporation. All rights reserved.
+ *
+ * Copyright (C) 2006 Michael Buesch
+ *
+ * Original Authors: Mitch Lichtenberg, Chris Demetriou
+ *
+ * This software is furnished under license and may be used and copied only
+ * in accordance with the following terms and conditions. Subject to these
+ * conditions, you may download, copy, install, use, modify and distribute
+ * modified or unmodified copies of this software in source and/or binary
+ * form. No title or ownership is transferred hereby.
+ *
+ * 1) Any source code used, modified or distributed must reproduce and
+ * retain this copyright notice and list of conditions as they appear in
+ * the source file.
+ *
+ * 2) No right is granted to use any trade name, trademark, or logo of
+ * Broadcom Corporation. The "Broadcom Corporation" name may not be
+ * used to endorse or promote products derived from this software
+ * without the prior written permission of Broadcom Corporation.
+ *
+ * 3) THIS SOFTWARE IS PROVIDED "AS-IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
+ * NON-INFRINGEMENT ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM BE LIABLE
+ * FOR ANY DAMAGES WHATSOEVER, AND IN PARTICULAR, BROADCOM SHALL NOT BE
+ * LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE), EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#ifndef LINUX_CFE_API_H_
+#define LINUX_CFE_API_H_
+
+#include <linux/types.h>
+
+
+#define CFE_MI_RESERVED 0 /* memory is reserved, do not use */
+#define CFE_MI_AVAILABLE 1 /* memory is available */
+
+#define CFE_FLG_WARMSTART 0x00000001
+#define CFE_FLG_FULL_ARENA 0x00000001
+#define CFE_FLG_ENV_PERMANENT 0x00000001
+
+#define CFE_CPU_CMD_START 1
+#define CFE_CPU_CMD_STOP 0
+
+#define CFE_STDHANDLE_CONSOLE 0
+
+#define CFE_DEV_NETWORK 1
+#define CFE_DEV_DISK 2
+#define CFE_DEV_FLASH 3
+#define CFE_DEV_SERIAL 4
+#define CFE_DEV_CPU 5
+#define CFE_DEV_NVRAM 6
+#define CFE_DEV_CLOCK 7
+#define CFE_DEV_OTHER 8
+#define CFE_DEV_MASK 0x0F
+
+#define CFE_CACHE_FLUSH_D 1
+#define CFE_CACHE_INVAL_I 2
+#define CFE_CACHE_INVAL_D 4
+#define CFE_CACHE_INVAL_L2 8
+
+#define CFE_FWI_64BIT 0x00000001
+#define CFE_FWI_32BIT 0x00000002
+#define CFE_FWI_RELOC 0x00000004
+#define CFE_FWI_UNCACHED 0x00000008
+#define CFE_FWI_MULTICPU 0x00000010
+#define CFE_FWI_FUNCSIM 0x00000020
+#define CFE_FWI_RTLSIM 0x00000040
+
+struct cfe_fwinfo {
+ s64 version; /* major, minor, eco version */
+ s64 totalmem; /* total installed mem */
+ s64 flags; /* various flags */
+ s64 boardid; /* board ID */
+ s64 bootarea_va; /* VA of boot area */
+ s64 bootarea_pa; /* PA of boot area */
+ s64 bootarea_size; /* size of boot area */
+};
+
+
+/* The public CFE API */
+
+int cfe_present(void); /* Check if we booted from CFE. Returns bool */
+
+int cfe_getticks(s64 *ticks);
+int cfe_close(int handle);
+int cfe_cpu_start(int cpu, void (*fn)(void), long sp, long gp, long a1);
+int cfe_cpu_stop(int cpu);
+int cfe_enumenv(int idx, char *name, int namelen, char *val, int vallen);
+int cfe_enumdev(int idx, char *name, int namelen);
+int cfe_enummem(int idx, int flags, u64 *start, u64 *length,
+ u64 *type);
+int cfe_exit(int warm, int status);
+int cfe_flushcache(int flags);
+int cfe_getdevinfo(char *name);
+int cfe_getenv(char *name, char *dest, int destlen);
+int cfe_getfwinfo(struct cfe_fwinfo *info);
+int cfe_getstdhandle(int handletype);
+int cfe_inpstat(int handle);
+int cfe_ioctl(int handle, unsigned int ioctlnum, unsigned char *buffer,
+ int length, int *retlen, u64 offset);
+int cfe_open(char *name);
+int cfe_read(int handle, unsigned char *buffer, int length);
+int cfe_readblk(int handle, s64 offset, unsigned char *buffer, int length);
+int cfe_setenv(char *name, char *val);
+int cfe_write(int handle, unsigned char *buffer, int length);
+int cfe_writeblk(int handle, s64 offset, unsigned char *buffer,
+ int length);
+
+
+/* High level API */
+
+/* Print some information to CFE's console (most likely serial line) */
+int cfe_printk(const char *fmt, ...) __attribute__((format(printf, 1, 2)));
+int cfe_vprintk(const char *fmt, va_list args);
+
+
+
+/* Error codes returned by the low API functions */
+
+#define CFE_ISERR(errcode) (errcode < 0)
+
+#define CFE_OK 0
+#define CFE_ERR -1 /* generic error */
+#define CFE_ERR_INV_COMMAND -2
+#define CFE_ERR_EOF -3
+#define CFE_ERR_IOERR -4
+#define CFE_ERR_NOMEM -5
+#define CFE_ERR_DEVNOTFOUND -6
+#define CFE_ERR_DEVOPEN -7
+#define CFE_ERR_INV_PARAM -8
+#define CFE_ERR_ENVNOTFOUND -9
+#define CFE_ERR_ENVREADONLY -10
+
+#define CFE_ERR_NOTELF -11
+#define CFE_ERR_NOT32BIT -12
+#define CFE_ERR_WRONGENDIAN -13
+#define CFE_ERR_BADELFVERS -14
+#define CFE_ERR_NOTMIPS -15
+#define CFE_ERR_BADELFFMT -16
+#define CFE_ERR_BADADDR -17
+
+#define CFE_ERR_FILENOTFOUND -18
+#define CFE_ERR_UNSUPPORTED -19
+
+#define CFE_ERR_HOSTUNKNOWN -20
+
+#define CFE_ERR_TIMEOUT -21
+
+#define CFE_ERR_PROTOCOLERR -22
+
+#define CFE_ERR_NETDOWN -23
+#define CFE_ERR_NONAMESERVER -24
+
+#define CFE_ERR_NOHANDLES -25
+#define CFE_ERR_ALREADYBOUND -26
+
+#define CFE_ERR_CANNOTSET -27
+#define CFE_ERR_NOMORE -28
+#define CFE_ERR_BADFILESYS -29
+#define CFE_ERR_FSNOTAVAIL -30
+
+#define CFE_ERR_INVBOOTBLOCK -31
+#define CFE_ERR_WRONGDEVTYPE -32
+#define CFE_ERR_BBCHECKSUM -33
+#define CFE_ERR_BOOTPROGCHKSUM -34
+
+#define CFE_ERR_LDRNOTAVAIL -35
+
+#define CFE_ERR_NOTREADY -36
+
+#define CFE_ERR_GETMEM -37
+#define CFE_ERR_SETMEM -38
+
+#define CFE_ERR_NOTCONN -39
+#define CFE_ERR_ADDRINUSE -40
+
+
+#endif /* LINUX_CFE_API_H_ */
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2003 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+
+#ifndef __6338_INTR_H
+#define __6338_INTR_H
+
+/*=====================================================================*/
+/* BCM6338 External Interrupt Level Assignments */
+/*=====================================================================*/
+#define INTERRUPT_ID_EXTERNAL_0 3
+#define INTERRUPT_ID_EXTERNAL_1 4
+#define INTERRUPT_ID_EXTERNAL_2 5
+#define INTERRUPT_ID_EXTERNAL_3 6
+
+/*=====================================================================*/
+/* BCM6338 Timer Interrupt Level Assignments */
+/*=====================================================================*/
+#define MIPS_TIMER_INT 7
+
+/*=====================================================================*/
+/* Peripheral ISR Table Offset */
+/*=====================================================================*/
+#define INTERNAL_ISR_TABLE_OFFSET 8
+
+/*=====================================================================*/
+/* Logical Peripheral Interrupt IDs */
+/*=====================================================================*/
+
+#define INTERRUPT_ID_TIMER (INTERNAL_ISR_TABLE_OFFSET + 0)
+#define INTERRUPT_ID_SPI (INTERNAL_ISR_TABLE_OFFSET + 1)
+#define INTERRUPT_ID_UART (INTERNAL_ISR_TABLE_OFFSET + 2)
+#define INTERRUPT_ID_DG (INTERNAL_ISR_TABLE_OFFSET + 4)
+#define INTERRUPT_ID_ADSL (INTERNAL_ISR_TABLE_OFFSET + 5)
+#define INTERRUPT_ID_ATM (INTERNAL_ISR_TABLE_OFFSET + 6)
+#define INTERRUPT_ID_USBS (INTERNAL_ISR_TABLE_OFFSET + 7)
+#define INTERRUPT_ID_EMAC1 (INTERNAL_ISR_TABLE_OFFSET + 8)
+#define INTERRUPT_ID_EPHY (INTERNAL_ISR_TABLE_OFFSET + 9)
+#define INTERRUPT_ID_SDRAM (INTERNAL_ISR_TABLE_OFFSET + 10)
+#define INTERRUPT_ID_USB_CNTL_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 11)
+#define INTERRUPT_ID_USB_CNTL_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 12)
+#define INTERRUPT_ID_USB_BULK_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 13)
+#define INTERRUPT_ID_USB_BULK_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 14)
+#define INTERRUPT_ID_EMAC1_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 15)
+#define INTERRUPT_ID_EMAC1_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 16)
+#define INTERRUPT_ID_SDIO (INTERNAL_ISR_TABLE_OFFSET + 17)
+
+#endif /* __BCM6338_H */
+
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2004 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+
+#ifndef __BCM6338_MAP_H
+#define __BCM6338_MAP_H
+
+#include "bcmtypes.h"
+
+#define PERF_BASE 0xfffe0000
+#define TIMR_BASE 0xfffe0200
+#define UART_BASE 0xfffe0300
+#define GPIO_BASE 0xfffe0400
+#define SPI_BASE 0xfffe0c00
+
+typedef struct PerfControl {
+ uint32 RevID;
+ uint16 testControl;
+ uint16 blkEnables;
+#define EMAC_CLK_EN 0x0010
+#define USBS_CLK_EN 0x0010
+#define SAR_CLK_EN 0x0020
+
+#define SPI_CLK_EN 0x0200
+
+ uint32 pll_control;
+#define SOFT_RESET 0x00000001
+
+ uint32 IrqMask;
+ uint32 IrqStatus;
+
+ uint32 ExtIrqCfg;
+#define EI_SENSE_SHFT 0
+#define EI_STATUS_SHFT 5
+#define EI_CLEAR_SHFT 10
+#define EI_MASK_SHFT 15
+#define EI_INSENS_SHFT 20
+#define EI_LEVEL_SHFT 25
+
+ uint32 unused[4]; /* (18) */
+ uint32 BlockSoftReset; /* (28) */
+#define BSR_SPI 0x00000001
+#define BSR_EMAC 0x00000004
+#define BSR_USBH 0x00000008
+#define BSR_USBS 0x00000010
+#define BSR_ADSL 0x00000020
+#define BSR_DMAMEM 0x00000040
+#define BSR_SAR 0x00000080
+#define BSR_ACLC 0x00000100
+#define BSR_ADSL_MIPS_PLL 0x00000400
+#define BSR_ALL_BLOCKS \
+ (BSR_SPI | BSR_EMAC | BSR_USBH | BSR_USBS | BSR_ADSL | BSR_DMAMEM | \
+ BSR_SAR | BSR_ACLC | BSR_ADSL_MIPS_PLL)
+} PerfControl;
+
+#define PERF ((volatile PerfControl * const) PERF_BASE)
+
+
+typedef struct Timer {
+ uint16 unused0;
+ byte TimerMask;
+#define TIMER0EN 0x01
+#define TIMER1EN 0x02
+#define TIMER2EN 0x04
+ byte TimerInts;
+#define TIMER0 0x01
+#define TIMER1 0x02
+#define TIMER2 0x04
+#define WATCHDOG 0x08
+ uint32 TimerCtl0;
+ uint32 TimerCtl1;
+ uint32 TimerCtl2;
+#define TIMERENABLE 0x80000000
+#define RSTCNTCLR 0x40000000
+ uint32 TimerCnt0;
+ uint32 TimerCnt1;
+ uint32 TimerCnt2;
+ uint32 WatchDogDefCount;
+
+ /* Write 0xff00 0x00ff to Start timer
+ * Write 0xee00 0x00ee to Stop and re-load default count
+ * Read from this register returns current watch dog count
+ */
+ uint32 WatchDogCtl;
+
+ /* Number of 40-MHz ticks for WD Reset pulse to last */
+ uint32 WDResetCount;
+} Timer;
+
+#define TIMER ((volatile Timer * const) TIMR_BASE)
+typedef struct UartChannel {
+ byte unused0;
+ byte control;
+#define BRGEN 0x80 /* Control register bit defs */
+#define TXEN 0x40
+#define RXEN 0x20
+#define LOOPBK 0x10
+#define TXPARITYEN 0x08
+#define TXPARITYEVEN 0x04
+#define RXPARITYEN 0x02
+#define RXPARITYEVEN 0x01
+
+ byte config;
+#define XMITBREAK 0x40
+#define BITS5SYM 0x00
+#define BITS6SYM 0x10
+#define BITS7SYM 0x20
+#define BITS8SYM 0x30
+#define ONESTOP 0x07
+#define TWOSTOP 0x0f
+ /* 4-LSBS represent STOP bits/char
+ * in 1/8 bit-time intervals. Zero
+ * represents 1/8 stop bit interval.
+ * Fifteen represents 2 stop bits.
+ */
+ byte fifoctl;
+#define RSTTXFIFOS 0x80
+#define RSTRXFIFOS 0x40
+ /* 5-bit TimeoutCnt is in low bits of this register.
+ * This count represents the number of characters
+ * idle times before setting receive Irq when below threshold
+ */
+ uint32 baudword;
+ /* When divide SysClk/2/(1+baudword) we should get 32*bit-rate
+ */
+
+ byte txf_levl; /* Read-only fifo depth */
+ byte rxf_levl; /* Read-only fifo depth */
+ byte fifocfg; /* Upper 4-bits are TxThresh, Lower are
+ * RxThreshold. Irq can be asserted
+ * when rx fifo> thresh, txfifo<thresh
+ */
+ byte prog_out; /* Set value of DTR (Bit0), RTS (Bit1)
+ * if these bits are also enabled to GPIO_o
+ */
+#define DTREN 0x01
+#define RTSEN 0x02
+
+ byte unused1;
+ byte DeltaIPEdgeNoSense; /* Low 4-bits, set corr bit to 1 to
+ * detect irq on rising AND falling
+ * edges for corresponding GPIO_i
+ * if enabled (edge insensitive)
+ */
+ byte DeltaIPConfig_Mask; /* Upper 4 bits: 1 for posedge sense
+ * 0 for negedge sense if
+ * not configured for edge
+ * insensitive (see above)
+ * Lower 4 bits: Mask to enable change
+ * detection IRQ for corresponding
+ * GPIO_i
+ */
+ byte DeltaIP_SyncIP; /* Upper 4 bits show which bits
+ * have changed (may set IRQ).
+ * read automatically clears bit
+ * Lower 4 bits are actual status
+ */
+
+ uint16 intMask; /* Same Bit defs for Mask and status */
+ uint16 intStatus;
+#define DELTAIP 0x0001
+#define TXUNDERR 0x0002
+#define TXOVFERR 0x0004
+#define TXFIFOTHOLD 0x0008
+#define TXREADLATCH 0x0010
+#define TXFIFOEMT 0x0020
+#define RXUNDERR 0x0040
+#define RXOVFERR 0x0080
+#define RXTIMEOUT 0x0100
+#define RXFIFOFULL 0x0200
+#define RXFIFOTHOLD 0x0400
+#define RXFIFONE 0x0800
+#define RXFRAMERR 0x1000
+#define RXPARERR 0x2000
+#define RXBRK 0x4000
+
+ uint16 unused2;
+ uint16 Data; /* Write to TX, Read from RX */
+ /* bits 11:8 are BRK,PAR,FRM errors */
+
+ uint32 unused3;
+ uint32 unused4;
+} Uart;
+
+#define UART ((volatile Uart * const) UART_BASE)
+
+typedef struct GpioControl {
+ uint32 unused0;
+ uint32 GPIODir; /* bits 7:0 */
+ uint32 unused1;
+ uint32 GPIOio; /* bits 7:0 */
+ uint32 LEDCtrl;
+#define LED3_STROBE 0x08000000
+#define LED2_STROBE 0x04000000
+#define LED1_STROBE 0x02000000
+#define LED0_STROBE 0x01000000
+#define LED_TEST 0x00010000
+#define LED3_DISABLE_LINK_ACT 0x00008000
+#define LED2_DISABLE_LINK_ACT 0x00004000
+#define LED1_DISABLE_LINK_ACT 0x00002000
+#define LED0_DISABLE_LINK_ACT 0x00001000
+#define LED_INTERVAL_SET_MASK 0x00000f00
+#define LED_INTERVAL_SET_320MS 0x00000500
+#define LED_INTERVAL_SET_160MS 0x00000400
+#define LED_INTERVAL_SET_80MS 0x00000300
+#define LED_INTERVAL_SET_40MS 0x00000200
+#define LED_INTERVAL_SET_20MS 0x00000100
+#define LED3_ON 0x00000080
+#define LED2_ON 0x00000040
+#define LED1_ON 0x00000020
+#define LED0_ON 0x00000010
+#define LED3_ENABLE 0x00000008
+#define LED2_ENABLE 0x00000004
+#define LED1_ENABLE 0x00000002
+#define LED0_ENABLE 0x00000001
+ uint32 SpiSlaveCfg;
+#define SPI_SLAVE_RESET 0x00010000
+#define SPI_RESTRICT 0x00000400
+#define SPI_DELAY_DISABLE 0x00000200
+#define SPI_PROBE_MUX_SEL_MASK 0x000001e0
+#define SPI_SER_ADDR_CFG_MASK 0x0000000c
+#define SPI_MODE 0x00000001
+ uint32 vRegConfig;
+} GpioControl;
+
+#define GPIO ((volatile GpioControl * const) GPIO_BASE)
+
+/* Number to mask conversion macro used for GPIODir and GPIOio */
+#define GPIO_NUM_MAX_BITS_MASK 0x0f
+#define GPIO_NUM_TO_MASK(X) (1 << ((X) & GPIO_NUM_MAX_BITS_MASK))
+
+/*
+** Spi Controller
+*/
+
+typedef struct SpiControl {
+ uint16 spiCmd; /* (0x0): SPI command */
+#define SPI_CMD_START_IMMEDIATE 3
+
+#define SPI_CMD_COMMAND_SHIFT 0
+#define SPI_CMD_DEVICE_ID_SHIFT 4
+#define SPI_CMD_PREPEND_BYTE_CNT_SHIFT 8
+
+ byte spiIntStatus; /* (0x2): SPI interrupt status */
+ byte spiMaskIntStatus; /* (0x3): SPI masked interrupt status */
+
+ byte spiIntMask; /* (0x4): SPI interrupt mask */
+#define SPI_INTR_CMD_DONE 0x01
+#define SPI_INTR_CLEAR_ALL 0x1f
+
+ byte spiStatus; /* (0x5): SPI status */
+
+ byte spiClkCfg; /* (0x6): SPI clock configuration */
+
+ byte spiFillByte; /* (0x7): SPI fill byte */
+
+ byte unused0;
+ byte spiMsgTail; /* (0x9): msgtail */
+ byte unused1;
+ byte spiRxTail; /* (0xB): rxtail */
+
+ uint32 unused2[13]; /* (0x0c - 0x3c) reserved */
+
+ byte spiMsgCtl; /* (0x40) control byte */
+#define HALF_DUPLEX_W 1
+#define HALF_DUPLEX_R 2
+#define SPI_MSG_TYPE_SHIFT 6
+#define SPI_BYTE_CNT_SHIFT 0
+ byte spiMsgData[63]; /* (0x41 - 0x7f) msg data */
+ byte spiRxDataFifo[64]; /* (0x80 - 0xbf) rx data */
+ byte unused3[64]; /* (0xc0 - 0xff) reserved */
+} SpiControl;
+
+#define SPI ((volatile SpiControl * const) SPI_BASE)
+
+/*
+** External Bus Interface
+*/
+typedef struct EbiChipSelect {
+ uint32 base; /* base address in upper 24 bits */
+#define EBI_SIZE_8K 0
+#define EBI_SIZE_16K 1
+#define EBI_SIZE_32K 2
+#define EBI_SIZE_64K 3
+#define EBI_SIZE_128K 4
+#define EBI_SIZE_256K 5
+#define EBI_SIZE_512K 6
+#define EBI_SIZE_1M 7
+#define EBI_SIZE_2M 8
+#define EBI_SIZE_4M 9
+#define EBI_SIZE_8M 10
+#define EBI_SIZE_16M 11
+#define EBI_SIZE_32M 12
+#define EBI_SIZE_64M 13
+#define EBI_SIZE_128M 14
+#define EBI_SIZE_256M 15
+ uint32 config;
+#define EBI_ENABLE 0x00000001 /* .. enable this range */
+#define EBI_WAIT_STATES 0x0000000e /* .. mask for wait states */
+#define EBI_WTST_SHIFT 1 /* .. for shifting wait states */
+#define EBI_WORD_WIDE 0x00000010 /* .. 16-bit peripheral, else 8 */
+#define EBI_WREN 0x00000020 /* enable posted writes */
+#define EBI_POLARITY 0x00000040 /* .. set to invert something,
+ ** don't know what yet */
+#define EBI_TS_TA_MODE 0x00000080 /* .. use TS/TA mode */
+#define EBI_TS_SEL 0x00000100 /* .. drive tsize, not bs_b */
+#define EBI_FIFO 0x00000200 /* .. use fifo */
+#define EBI_RE 0x00000400 /* .. Reverse Endian */
+} EbiChipSelect;
+
+typedef struct MpiRegisters {
+ EbiChipSelect cs[1]; /* size chip select configuration */
+} MpiRegisters;
+
+#define MPI ((volatile MpiRegisters * const) MPI_BASE)
+
+
+#endif
+
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2002 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+
+#ifndef __6345_INTR_H
+#define __6345_INTR_H
+
+
+/*=====================================================================*/
+/* BCM6345 External Interrupt Level Assignments */
+/*=====================================================================*/
+#define INTERRUPT_ID_EXTERNAL_0 3
+#define INTERRUPT_ID_EXTERNAL_1 4
+#define INTERRUPT_ID_EXTERNAL_2 5
+#define INTERRUPT_ID_EXTERNAL_3 6
+
+/*=====================================================================*/
+/* BCM6345 Timer Interrupt Level Assignments */
+/*=====================================================================*/
+#define MIPS_TIMER_INT 7
+
+/*=====================================================================*/
+/* Peripheral ISR Table Offset */
+/*=====================================================================*/
+#define INTERNAL_ISR_TABLE_OFFSET 8
+#define DMA_ISR_TABLE_OFFSET (INTERNAL_ISR_TABLE_OFFSET + 13)
+
+/*=====================================================================*/
+/* Logical Peripheral Interrupt IDs */
+/*=====================================================================*/
+
+/* Internal peripheral interrupt IDs */
+#define INTERRUPT_ID_TIMER (INTERNAL_ISR_TABLE_OFFSET + 0)
+#define INTERRUPT_ID_UART (INTERNAL_ISR_TABLE_OFFSET + 2)
+#define INTERRUPT_ID_ADSL (INTERNAL_ISR_TABLE_OFFSET + 3)
+#define INTERRUPT_ID_ATM (INTERNAL_ISR_TABLE_OFFSET + 4)
+#define INTERRUPT_ID_USB (INTERNAL_ISR_TABLE_OFFSET + 5)
+#define INTERRUPT_ID_EMAC (INTERNAL_ISR_TABLE_OFFSET + 8)
+#define INTERRUPT_ID_EPHY (INTERNAL_ISR_TABLE_OFFSET + 12)
+
+/* DMA channel interrupt IDs */
+#define INTERRUPT_ID_EMAC_RX_CHAN (DMA_ISR_TABLE_OFFSET + EMAC_RX_CHAN)
+#define INTERRUPT_ID_EMAC_TX_CHAN (DMA_ISR_TABLE_OFFSET + EMAC_TX_CHAN)
+#define INTERRUPT_ID_EBI_RX_CHAN (DMA_ISR_TABLE_OFFSET + EBI_RX_CHAN)
+#define INTERRUPT_ID_EBI_TX_CHAN (DMA_ISR_TABLE_OFFSET + EBI_TX_CHAN)
+#define INTERRUPT_ID_RESERVED_RX_CHAN (DMA_ISR_TABLE_OFFSET + RESERVED_RX_CHAN)
+#define INTERRUPT_ID_RESERVED_TX_CHAN (DMA_ISR_TABLE_OFFSET + RESERVED_TX_CHAN)
+#define INTERRUPT_ID_USB_BULK_RX_CHAN (DMA_ISR_TABLE_OFFSET + USB_BULK_RX_CHAN)
+#define INTERRUPT_ID_USB_BULK_TX_CHAN (DMA_ISR_TABLE_OFFSET + USB_BULK_TX_CHAN)
+#define INTERRUPT_ID_USB_CNTL_RX_CHAN (DMA_ISR_TABLE_OFFSET + USB_CNTL_RX_CHAN)
+#define INTERRUPT_ID_USB_CNTL_TX_CHAN (DMA_ISR_TABLE_OFFSET + USB_CNTL_TX_CHAN)
+#define INTERRUPT_ID_USB_ISO_RX_CHAN (DMA_ISR_TABLE_OFFSET + USB_ISO_RX_CHAN)
+#define INTERRUPT_ID_USB_ISO_TX_CHAN (DMA_ISR_TABLE_OFFSET + USB_ISO_TX_CHAN)
+
+
+#endif /* __BCM6345_H */
+
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2002 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+
+#ifndef __BCM6345_MAP_H
+#define __BCM6345_MAP_H
+
+
+#include "bcmtypes.h"
+#include "6345_intr.h"
+
+typedef struct IntControl {
+ uint32 RevID;
+ uint16 testControl;
+ uint16 blkEnables;
+#define USB_CLK_EN 0x0100
+#define EMAC_CLK_EN 0x0080
+#define UART_CLK_EN 0x0008
+#define CPU_CLK_EN 0x0001
+
+ uint32 pll_control;
+#define SOFT_RESET 0x00000001
+
+ uint32 IrqMask;
+ uint32 IrqStatus;
+
+ uint32 ExtIrqCfg;
+#define EI_SENSE_SHFT 0
+#define EI_STATUS_SHFT 4
+#define EI_CLEAR_SHFT 8
+#define EI_MASK_SHFT 12
+#define EI_INSENS_SHFT 16
+#define EI_LEVEL_SHFT 20
+} IntControl;
+
+#define INTC_BASE 0xfffe0000
+#define PERF ((volatile IntControl * const) INTC_BASE)
+
+#define TIMR_BASE 0xfffe0200
+typedef struct Timer {
+ uint16 unused0;
+ byte TimerMask;
+#define TIMER0EN 0x01
+#define TIMER1EN 0x02
+#define TIMER2EN 0x04
+ byte TimerInts;
+#define TIMER0 0x01
+#define TIMER1 0x02
+#define TIMER2 0x04
+#define WATCHDOG 0x08
+ uint32 TimerCtl0;
+ uint32 TimerCtl1;
+ uint32 TimerCtl2;
+#define TIMERENABLE 0x80000000
+#define RSTCNTCLR 0x40000000
+ uint32 TimerCnt0;
+ uint32 TimerCnt1;
+ uint32 TimerCnt2;
+ uint32 WatchDogDefCount;
+
+ /* Write 0xff00 0x00ff to Start timer
+ * Write 0xee00 0x00ee to Stop and re-load default count
+ * Read from this register returns current watch dog count
+ */
+ uint32 WatchDogCtl;
+
+ /* Number of 40-MHz ticks for WD Reset pulse to last */
+ uint32 WDResetCount;
+} Timer;
+
+#define TIMER ((volatile Timer * const) TIMR_BASE)
+
+typedef struct UartChannel {
+ byte unused0;
+ byte control;
+#define BRGEN 0x80 /* Control register bit defs */
+#define TXEN 0x40
+#define RXEN 0x20
+#define TXPARITYEN 0x08
+#define TXPARITYEVEN 0x04
+#define RXPARITYEN 0x02
+#define RXPARITYEVEN 0x01
+ byte config;
+#define BITS5SYM 0x00
+#define BITS6SYM 0x10
+#define BITS7SYM 0x20
+#define BITS8SYM 0x30
+#define XMITBREAK 0x40
+#define ONESTOP 0x07
+#define TWOSTOP 0x0f
+
+ byte fifoctl;
+#define RSTTXFIFOS 0x80
+#define RSTRXFIFOS 0x40
+ uint32 baudword;
+
+ byte txf_levl;
+ byte rxf_levl;
+ byte fifocfg;
+ byte prog_out;
+
+ byte unused1;
+ byte DeltaIPEdgeNoSense;
+ byte DeltaIPConfig_Mask;
+ byte DeltaIP_SyncIP;
+ uint16 intMask;
+ uint16 intStatus;
+#define TXUNDERR 0x0002
+#define TXOVFERR 0x0004
+#define TXFIFOEMT 0x0020
+#define RXOVFERR 0x0080
+#define RXFIFONE 0x0800
+#define RXFRAMERR 0x1000
+#define RXPARERR 0x2000
+#define RXBRK 0x4000
+
+ uint16 unused2;
+ uint16 Data;
+ uint32 unused3;
+ uint32 unused4;
+} Uart;
+
+#define UART_BASE 0xfffe0300
+#define UART ((volatile Uart * const) UART_BASE)
+
+typedef struct GpioControl {
+ uint16 unused0;
+ byte unused1;
+ byte TBusSel;
+
+ uint16 unused2;
+ uint16 GPIODir;
+ byte unused3;
+ byte Leds;
+ uint16 GPIOio;
+
+ uint32 UartCtl;
+} GpioControl;
+
+#define GPIO_BASE 0xfffe0400
+#define GPIO ((volatile GpioControl * const) GPIO_BASE)
+
+#define GPIO_NUM_MAX_BITS_MASK 0x0f
+#define GPIO_NUM_TO_MASK(X) (1 << ((X) & GPIO_NUM_MAX_BITS_MASK))
+
+
+#endif
+
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2003 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+
+#ifndef __6348_INTR_H
+#define __6348_INTR_H
+
+
+/*=====================================================================*/
+/* BCM6348 External Interrupt Level Assignments */
+/*=====================================================================*/
+#define INTERRUPT_ID_EXTERNAL_0 3
+#define INTERRUPT_ID_EXTERNAL_1 4
+#define INTERRUPT_ID_EXTERNAL_2 5
+#define INTERRUPT_ID_EXTERNAL_3 6
+
+/*=====================================================================*/
+/* BCM6348 Timer Interrupt Level Assignments */
+/*=====================================================================*/
+#define MIPS_TIMER_INT 7
+
+/*=====================================================================*/
+/* Peripheral ISR Table Offset */
+/*=====================================================================*/
+#define INTERNAL_ISR_TABLE_OFFSET 8
+
+/*=====================================================================*/
+/* Logical Peripheral Interrupt IDs */
+/*=====================================================================*/
+
+#define INTERRUPT_ID_TIMER (INTERNAL_ISR_TABLE_OFFSET + 0)
+#define INTERRUPT_ID_SPI (INTERNAL_ISR_TABLE_OFFSET + 1)
+#define INTERRUPT_ID_UART (INTERNAL_ISR_TABLE_OFFSET + 2)
+#define INTERRUPT_ID_ADSL (INTERNAL_ISR_TABLE_OFFSET + 4)
+#define INTERRUPT_ID_ATM (INTERNAL_ISR_TABLE_OFFSET + 5)
+#define INTERRUPT_ID_USBS (INTERNAL_ISR_TABLE_OFFSET + 6)
+#define INTERRUPT_ID_EMAC2 (INTERNAL_ISR_TABLE_OFFSET + 7)
+#define INTERRUPT_ID_EMAC1 (INTERNAL_ISR_TABLE_OFFSET + 8)
+#define INTERRUPT_ID_EPHY (INTERNAL_ISR_TABLE_OFFSET + 9)
+#define INTERRUPT_ID_M2M (INTERNAL_ISR_TABLE_OFFSET + 10)
+#define INTERRUPT_ID_ACLC (INTERNAL_ISR_TABLE_OFFSET + 11)
+#define INTERRUPT_ID_USBH (INTERNAL_ISR_TABLE_OFFSET + 12)
+#define INTERRUPT_ID_SDRAM (INTERNAL_ISR_TABLE_OFFSET + 13)
+#define INTERRUPT_ID_USB_CNTL_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 14)
+#define INTERRUPT_ID_USB_CNTL_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 15)
+#define INTERRUPT_ID_USB_BULK_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 16)
+#define INTERRUPT_ID_USB_BULK_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 17)
+#define INTERRUPT_ID_USB_ISO_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 18)
+#define INTERRUPT_ID_USB_ISO_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 19)
+#define INTERRUPT_ID_EMAC1_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 20)
+#define INTERRUPT_ID_EMAC1_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 21)
+#define INTERRUPT_ID_EMAC2_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 22)
+#define INTERRUPT_ID_EMAC2_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 23)
+#define INTERRUPT_ID_MPI (INTERNAL_ISR_TABLE_OFFSET + 24)
+#define INTERRUPT_ID_DG (INTERNAL_ISR_TABLE_OFFSET + 25)
+
+
+#endif /* __BCM6348_H */
+
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2002 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+
+#ifndef __BCM6348_MAP_H
+#define __BCM6348_MAP_H
+
+#include "bcmtypes.h"
+
+#define PERF_BASE 0xfffe0000
+#define TIMR_BASE 0xfffe0200
+#define UART_BASE 0xfffe0300
+#define GPIO_BASE 0xfffe0400
+#define MPI_BASE 0xfffe2000 /* MPI control registers */
+#define USB_HOST_BASE 0xfffe1b00 /* USB host registers */
+#define USB_HOST_NON_OHCI 0xfffe1c00 /* USB host non-OHCI registers */
+
+typedef struct PerfControl {
+ uint32 RevID;
+ uint16 testControl;
+ uint16 blkEnables;
+#define EMAC_CLK_EN 0x0010
+#define SAR_CLK_EN 0x0020
+#define USBS_CLK_EN 0x0040
+#define USBH_CLK_EN 0x0100
+
+ uint32 pll_control;
+#define SOFT_RESET 0x00000001
+
+ uint32 IrqMask;
+ uint32 IrqStatus;
+
+ uint32 ExtIrqCfg;
+#define EI_SENSE_SHFT 0
+#define EI_STATUS_SHFT 5
+#define EI_CLEAR_SHFT 10
+#define EI_MASK_SHFT 15
+#define EI_INSENS_SHFT 20
+#define EI_LEVEL_SHFT 25
+
+ uint32 unused[4]; /* (18) */
+ uint32 BlockSoftReset; /* (28) */
+#define BSR_SPI 0x00000001
+#define BSR_EMAC 0x00000004
+#define BSR_USBH 0x00000008
+#define BSR_USBS 0x00000010
+#define BSR_ADSL 0x00000020
+#define BSR_DMAMEM 0x00000040
+#define BSR_SAR 0x00000080
+#define BSR_ACLC 0x00000100
+#define BSR_ADSL_MIPS_PLL 0x00000400
+#define BSR_ALL_BLOCKS \
+ (BSR_SPI | BSR_EMAC | BSR_USBH | BSR_USBS | BSR_ADSL | BSR_DMAMEM | \
+ BSR_SAR | BSR_ACLC | BSR_ADSL_MIPS_PLL)
+ uint32 unused2[2]; /* (2c) */
+ uint32 PllStrap; /* (34) */
+#define PLL_N1_SHFT 20
+#define PLL_N1_MASK (7<<PLL_N1_SHFT)
+#define PLL_N2_SHFT 15
+#define PLL_N2_MASK (0x1f<<PLL_N2_SHFT)
+#define PLL_M1_REF_SHFT 12
+#define PLL_M1_REF_MASK (7<<PLL_M1_REF_SHFT)
+#define PLL_M2_REF_SHFT 9
+#define PLL_M2_REF_MASK (7<<PLL_M2_REF_SHFT)
+#define PLL_M1_CPU_SHFT 6
+#define PLL_M1_CPU_MASK (7<<PLL_M1_CPU_SHFT)
+#define PLL_M1_BUS_SHFT 3
+#define PLL_M1_BUS_MASK (7<<PLL_M1_BUS_SHFT)
+#define PLL_M2_BUS_SHFT 0
+#define PLL_M2_BUS_MASK (7<<PLL_M2_BUS_SHFT)
+} PerfControl;
+
+#define PERF ((volatile PerfControl * const) PERF_BASE)
+
+typedef struct Timer {
+ uint16 unused0;
+ byte TimerMask;
+#define TIMER0EN 0x01
+#define TIMER1EN 0x02
+#define TIMER2EN 0x04
+ byte TimerInts;
+#define TIMER0 0x01
+#define TIMER1 0x02
+#define TIMER2 0x04
+#define WATCHDOG 0x08
+ uint32 TimerCtl0;
+ uint32 TimerCtl1;
+ uint32 TimerCtl2;
+#define TIMERENABLE 0x80000000
+#define RSTCNTCLR 0x40000000
+ uint32 TimerCnt0;
+ uint32 TimerCnt1;
+ uint32 TimerCnt2;
+ uint32 WatchDogDefCount;
+
+ /* Write 0xff00 0x00ff to Start timer
+ * Write 0xee00 0x00ee to Stop and re-load default count
+ * Read from this register returns current watch dog count
+ */
+ uint32 WatchDogCtl;
+
+ /* Number of 40-MHz ticks for WD Reset pulse to last */
+ uint32 WDResetCount;
+} Timer;
+
+#define TIMER ((volatile Timer * const) TIMR_BASE)
+
+typedef struct UartChannel {
+ byte unused0;
+ byte control;
+#define BRGEN 0x80 /* Control register bit defs */
+#define TXEN 0x40
+#define RXEN 0x20
+#define LOOPBK 0x10
+#define TXPARITYEN 0x08
+#define TXPARITYEVEN 0x04
+#define RXPARITYEN 0x02
+#define RXPARITYEVEN 0x01
+
+ byte config;
+#define XMITBREAK 0x40
+#define BITS5SYM 0x00
+#define BITS6SYM 0x10
+#define BITS7SYM 0x20
+#define BITS8SYM 0x30
+#define ONESTOP 0x07
+#define TWOSTOP 0x0f
+ /* 4-LSBS represent STOP bits/char
+ * in 1/8 bit-time intervals. Zero
+ * represents 1/8 stop bit interval.
+ * Fifteen represents 2 stop bits.
+ */
+ byte fifoctl;
+#define RSTTXFIFOS 0x80
+#define RSTRXFIFOS 0x40
+ /* 5-bit TimeoutCnt is in low bits of this register.
+ * This count represents the number of characters
+ * idle times before setting receive Irq when below threshold
+ */
+ uint32 baudword;
+ /* When divide SysClk/2/(1+baudword) we should get 32*bit-rate
+ */
+
+ byte txf_levl; /* Read-only fifo depth */
+ byte rxf_levl; /* Read-only fifo depth */
+ byte fifocfg; /* Upper 4-bits are TxThresh, Lower are
+ * RxThreshold. Irq can be asserted
+ * when rx fifo> thresh, txfifo<thresh
+ */
+ byte prog_out; /* Set value of DTR (Bit0), RTS (Bit1)
+ * if these bits are also enabled to GPIO_o
+ */
+#define DTREN 0x01
+#define RTSEN 0x02
+
+ byte unused1;
+ byte DeltaIPEdgeNoSense; /* Low 4-bits, set corr bit to 1 to
+ * detect irq on rising AND falling
+ * edges for corresponding GPIO_i
+ * if enabled (edge insensitive)
+ */
+ byte DeltaIPConfig_Mask; /* Upper 4 bits: 1 for posedge sense
+ * 0 for negedge sense if
+ * not configured for edge
+ * insensitive (see above)
+ * Lower 4 bits: Mask to enable change
+ * detection IRQ for corresponding
+ * GPIO_i
+ */
+ byte DeltaIP_SyncIP; /* Upper 4 bits show which bits
+ * have changed (may set IRQ).
+ * read automatically clears bit
+ * Lower 4 bits are actual status
+ */
+
+ uint16 intMask; /* Same Bit defs for Mask and status */
+ uint16 intStatus;
+#define DELTAIP 0x0001
+#define TXUNDERR 0x0002
+#define TXOVFERR 0x0004
+#define TXFIFOTHOLD 0x0008
+#define TXREADLATCH 0x0010
+#define TXFIFOEMT 0x0020
+#define RXUNDERR 0x0040
+#define RXOVFERR 0x0080
+#define RXTIMEOUT 0x0100
+#define RXFIFOFULL 0x0200
+#define RXFIFOTHOLD 0x0400
+#define RXFIFONE 0x0800
+#define RXFRAMERR 0x1000
+#define RXPARERR 0x2000
+#define RXBRK 0x4000
+
+ uint16 unused2;
+ uint16 Data; /* Write to TX, Read from RX */
+ /* bits 11:8 are BRK,PAR,FRM errors */
+
+ uint32 unused3;
+ uint32 unused4;
+} Uart;
+
+#define UART ((volatile Uart * const) UART_BASE)
+
+typedef struct GpioControl {
+ uint32 GPIODir_high; /* bits 36:32 */
+ uint32 GPIODir; /* bits 31:00 */
+ uint32 GPIOio_high; /* bits 36:32 */
+ uint32 GPIOio; /* bits 31:00 */
+ uint32 LEDCtrl;
+#define LED3_STROBE 0x08000000
+#define LED2_STROBE 0x04000000
+#define LED1_STROBE 0x02000000
+#define LED0_STROBE 0x01000000
+#define LED_TEST 0x00010000
+#define LED3_DISABLE_LINK_ACT 0x00008000
+#define LED2_DISABLE_LINK_ACT 0x00004000
+#define LED1_DISABLE_LINK_ACT 0x00002000
+#define LED0_DISABLE_LINK_ACT 0x00001000
+#define LED_INTERVAL_SET_MASK 0x00000f00
+#define LED_INTERVAL_SET_320MS 0x00000500
+#define LED_INTERVAL_SET_160MS 0x00000400
+#define LED_INTERVAL_SET_80MS 0x00000300
+#define LED_INTERVAL_SET_40MS 0x00000200
+#define LED_INTERVAL_SET_20MS 0x00000100
+#define LED3_ON 0x00000080
+#define LED2_ON 0x00000040
+#define LED1_ON 0x00000020
+#define LED0_ON 0x00000010
+#define LED3_ENABLE 0x00000008
+#define LED2_ENABLE 0x00000004
+#define LED1_ENABLE 0x00000002
+#define LED0_ENABLE 0x00000001
+ uint32 SpiSlaveCfg;
+#define SPI_SLAVE_RESET 0x00010000
+#define SPI_RESTRICT 0x00000400
+#define SPI_DELAY_DISABLE 0x00000200
+#define SPI_PROBE_MUX_SEL_MASK 0x000001e0
+#define SPI_SER_ADDR_CFG_MASK 0x0000000c
+#define SPI_MODE 0x00000001
+ uint32 GPIOMode;
+#define GROUP4_DIAG 0x00090000
+#define GROUP4_UTOPIA 0x00080000
+#define GROUP4_LEGACY_LED 0x00030000
+#define GROUP4_MII_SNOOP 0x00020000
+#define GROUP4_EXT_EPHY 0x00010000
+#define GROUP3_DIAG 0x00009000
+#define GROUP3_UTOPIA 0x00008000
+#define GROUP3_EXT_MII 0x00007000
+#define GROUP2_DIAG 0x00000900
+#define GROUP2_PCI 0x00000500
+#define GROUP1_DIAG 0x00000090
+#define GROUP1_UTOPIA 0x00000080
+#define GROUP1_SPI_UART 0x00000060
+#define GROUP1_SPI_MASTER 0x00000060
+#define GROUP1_MII_PCCARD 0x00000040
+#define GROUP1_MII_SNOOP 0x00000020
+#define GROUP1_EXT_EPHY 0x00000010
+#define GROUP0_DIAG 0x00000009
+#define GROUP0_EXT_MII 0x00000007
+
+} GpioControl;
+
+#define GPIO ((volatile GpioControl * const) GPIO_BASE)
+
+/* Number to mask conversion macro used for GPIODir and GPIOio */
+#define GPIO_NUM_TOTAL_BITS_MASK 0x3f
+#define GPIO_NUM_MAX_BITS_MASK 0x1f
+#define GPIO_NUM_TO_MASK(X) ( (((X) & GPIO_NUM_TOTAL_BITS_MASK) < 32) ? (1 << ((X) & GPIO_NUM_MAX_BITS_MASK)) : (0) )
+
+/* Number to mask conversion macro used for GPIODir_high and GPIOio_high */
+#define GPIO_NUM_MAX_BITS_MASK_HIGH 0x07
+#define GPIO_NUM_TO_MASK_HIGH(X) ( (((X) & GPIO_NUM_TOTAL_BITS_MASK) >= 32) ? (1 << ((X-32) & GPIO_NUM_MAX_BITS_MASK_HIGH)) : (0) )
+
+
+/*
+** External Bus Interface
+*/
+typedef struct EbiChipSelect {
+ uint32 base; /* base address in upper 24 bits */
+#define EBI_SIZE_8K 0
+#define EBI_SIZE_16K 1
+#define EBI_SIZE_32K 2
+#define EBI_SIZE_64K 3
+#define EBI_SIZE_128K 4
+#define EBI_SIZE_256K 5
+#define EBI_SIZE_512K 6
+#define EBI_SIZE_1M 7
+#define EBI_SIZE_2M 8
+#define EBI_SIZE_4M 9
+#define EBI_SIZE_8M 10
+#define EBI_SIZE_16M 11
+#define EBI_SIZE_32M 12
+#define EBI_SIZE_64M 13
+#define EBI_SIZE_128M 14
+#define EBI_SIZE_256M 15
+ uint32 config;
+#define EBI_ENABLE 0x00000001 /* .. enable this range */
+#define EBI_WAIT_STATES 0x0000000e /* .. mask for wait states */
+#define EBI_WTST_SHIFT 1 /* .. for shifting wait states */
+#define EBI_WORD_WIDE 0x00000010 /* .. 16-bit peripheral, else 8 */
+#define EBI_WREN 0x00000020 /* enable posted writes */
+#define EBI_POLARITY 0x00000040 /* .. set to invert something,
+ ** don't know what yet */
+#define EBI_TS_TA_MODE 0x00000080 /* .. use TS/TA mode */
+#define EBI_TS_SEL 0x00000100 /* .. drive tsize, not bs_b */
+#define EBI_FIFO 0x00000200 /* .. use fifo */
+#define EBI_RE 0x00000400 /* .. Reverse Endian */
+} EbiChipSelect;
+
+typedef struct MpiRegisters {
+ EbiChipSelect cs[7]; /* size chip select configuration */
+#define EBI_CS0_BASE 0
+#define EBI_CS1_BASE 1
+#define EBI_CS2_BASE 2
+#define EBI_CS3_BASE 3
+#define PCMCIA_COMMON_BASE 4
+#define PCMCIA_ATTRIBUTE_BASE 5
+#define PCMCIA_IO_BASE 6
+ uint32 unused0[2]; /* reserved */
+ uint32 ebi_control; /* ebi control */
+ uint32 unused1[4]; /* reserved */
+#define EBI_ACCESS_TIMEOUT 0x000007FF
+ uint32 pcmcia_cntl1; /* pcmcia control 1 */
+#define PCCARD_CARD_RESET 0x00040000
+#define CARDBUS_ENABLE 0x00008000
+#define PCMCIA_ENABLE 0x00004000
+#define PCMCIA_GPIO_ENABLE 0x00002000
+#define CARDBUS_IDSEL 0x00001F00
+#define VS2_OEN 0x00000080
+#define VS1_OEN 0x00000040
+#define VS2_OUT 0x00000020
+#define VS1_OUT 0x00000010
+#define VS2_IN 0x00000008
+#define VS1_IN 0x00000004
+#define CD2_IN 0x00000002
+#define CD1_IN 0x00000001
+#define VS_MASK 0x0000000C
+#define CD_MASK 0x00000003
+ uint32 unused2; /* reserved */
+ uint32 pcmcia_cntl2; /* pcmcia control 2 */
+#define PCMCIA_BYTESWAP_DIS 0x00000002
+#define PCMCIA_HALFWORD_EN 0x00000001
+#define RW_ACTIVE_CNT_BIT 2
+#define INACTIVE_CNT_BIT 8
+#define CE_SETUP_CNT_BIT 16
+#define CE_HOLD_CNT_BIT 24
+ uint32 unused3[40]; /* reserved */
+
+ uint32 sp0range; /* PCI to internal system bus address space */
+ uint32 sp0remap;
+ uint32 sp0cfg;
+ uint32 sp1range;
+ uint32 sp1remap;
+ uint32 sp1cfg;
+
+ uint32 EndianCfg;
+
+ uint32 l2pcfgctl; /* internal system bus to PCI IO/Cfg control */
+#define DIR_CFG_SEL 0x80000000 /* change from PCI I/O access to PCI config access */
+#define DIR_CFG_USEREG 0x40000000 /* use this register info for PCI configuration access */
+#define DEVICE_NUMBER 0x00007C00 /* device number for the PCI configuration access */
+#define FUNC_NUMBER 0x00000300 /* function number for the PCI configuration access */
+#define REG_NUMBER 0x000000FC /* register number for the PCI configuration access */
+#define CONFIG_TYPE 0x00000003 /* configuration type for the PCI configuration access */
+
+ uint32 l2pmrange1; /* internal system bus to PCI memory space */
+#define PCI_SIZE_64K 0xFFFF0000
+#define PCI_SIZE_128K 0xFFFE0000
+#define PCI_SIZE_256K 0xFFFC0000
+#define PCI_SIZE_512K 0xFFF80000
+#define PCI_SIZE_1M 0xFFF00000
+#define PCI_SIZE_2M 0xFFE00000
+#define PCI_SIZE_4M 0xFFC00000
+#define PCI_SIZE_8M 0xFF800000
+#define PCI_SIZE_16M 0xFF000000
+#define PCI_SIZE_32M 0xFE000000
+ uint32 l2pmbase1; /* kseg0 or kseg1 address & 0x1FFFFFFF */
+ uint32 l2pmremap1;
+#define CARDBUS_MEM 0x00000004
+#define MEM_WINDOW_EN 0x00000001
+ uint32 l2pmrange2;
+ uint32 l2pmbase2;
+ uint32 l2pmremap2;
+ uint32 l2piorange; /* internal system bus to PCI I/O space */
+ uint32 l2piobase;
+ uint32 l2pioremap;
+
+ uint32 pcimodesel;
+#define PCI2_INT_BUS_RD_PREFECH 0x000000F0
+#define PCI_BAR2_NOSWAP 0x00000002 /* BAR at offset 0x20 */
+#define PCI_BAR1_NOSWAP 0x00000001 /* BAR at affset 0x1c */
+
+ uint32 pciintstat; /* PCI interrupt mask/status */
+#define MAILBOX1_SENT 0x08
+#define MAILBOX0_SENT 0x04
+#define MAILBOX1_MSG_RCV 0x02
+#define MAILBOX0_MSG_RCV 0x01
+ uint32 locbuscntrl; /* internal system bus control */
+#define DIR_U2P_NOSWAP 0x00000002
+#define EN_PCI_GPIO 0x00000001
+ uint32 locintstat; /* internal system bus interrupt mask/status */
+#define CSERR 0x0200
+#define SERR 0x0100
+#define EXT_PCI_INT 0x0080
+#define DIR_FAILED 0x0040
+#define DIR_COMPLETE 0x0020
+#define PCI_CFG 0x0010
+ uint32 unused5[7];
+
+ uint32 mailbox0;
+ uint32 mailbox1;
+
+ uint32 pcicfgcntrl; /* internal system bus PCI configuration control */
+#define PCI_CFG_REG_WRITE_EN 0x00000080
+#define PCI_CFG_ADDR 0x0000003C
+ uint32 pcicfgdata; /* internal system bus PCI configuration data */
+
+ uint32 locch2ctl; /* PCI to interrnal system bus DMA (downstream) local control */
+#define MPI_DMA_HALT 0x00000008 /* idle after finish current memory burst */
+#define MPI_DMA_PKT_HALT 0x00000004 /* idle after an EOP flag is detected */
+#define MPI_DMA_STALL 0x00000002 /* idle after an EOP flag is detected */
+#define MPI_DMA_ENABLE 0x00000001 /* set to enable channel */
+ uint32 locch2intStat;
+#define MPI_DMA_NO_DESC 0x00000004 /* no valid descriptors */
+#define MPI_DMA_DONE 0x00000002 /* packet xfer complete */
+#define MPI_DMA_BUFF_DONE 0x00000001 /* buffer done */
+ uint32 locch2intMask;
+ uint32 unused6;
+ uint32 locch2descaddr;
+ uint32 locch2status1;
+#define LOCAL_DESC_STATE 0xE0000000
+#define PCI_DESC_STATE 0x1C000000
+#define BYTE_DONE 0x03FFC000
+#define RING_ADDR 0x00003FFF
+ uint32 locch2status2;
+#define BUFPTR_OFFSET 0x1FFF0000
+#define PCI_MASTER_STATE 0x000000C0
+#define LOC_MASTER_STATE 0x00000038
+#define CONTROL_STATE 0x00000007
+ uint32 unused7;
+
+ uint32 locch1Ctl; /*internal system bus to PCI DMA (upstream) local control */
+#define DMA_U2P_LE 0x00000200 /* local bus is little endian */
+#define DMA_U2P_NOSWAP 0x00000100 /* lccal bus is little endian but no data swapped */
+ uint32 locch1intstat;
+ uint32 locch1intmask;
+ uint32 unused8;
+ uint32 locch1descaddr;
+ uint32 locch1status1;
+ uint32 locch1status2;
+ uint32 unused9;
+
+ uint32 pcich1ctl; /* internal system bus to PCI DMA PCI control */
+ uint32 pcich1intstat;
+ uint32 pcich1intmask;
+ uint32 pcich1descaddr;
+ uint32 pcich1status1;
+ uint32 pcich1status2;
+
+ uint32 pcich2Ctl; /* PCI to internal system bus DMA PCI control */
+ uint32 pcich2intstat;
+ uint32 pcich2intmask;
+ uint32 pcich2descaddr;
+ uint32 pcich2status1;
+ uint32 pcich2status2;
+
+ uint32 perm_id; /* permanent device and vendor id */
+ uint32 perm_rev; /* permanent revision id */
+} MpiRegisters;
+
+#define MPI ((volatile MpiRegisters * const) MPI_BASE)
+
+/* PCI configuration address space start offset 0x40 */
+#define BRCM_PCI_CONFIG_TIMER 0x40
+#define BRCM_PCI_CONFIG_TIMER_RETRY_MASK 0x0000FF00
+#define BRCM_PCI_CONFIG_TIMER_TRDY_MASK 0x000000FF
+
+/* USB host non-Open HCI register, USB_HOST_NON_OHCI, bit definitions. */
+#define NON_OHCI_ENABLE_PORT1 0x00000001 /* Use USB port 1 for host, not dev */
+#define NON_OHCI_BYTE_SWAP 0x00000008 /* Swap USB host registers */
+
+#define USBH_NON_OHCI ((volatile unsigned long * const) USB_HOST_NON_OHCI)
+
+#endif
+
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2002 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+//**************************************************************************************
+// File Name : bcmTag.h
+//
+// Description: add tag with validation system to the firmware image file to be uploaded
+// via http
+//
+// Created : 02/28/2002 seanl
+//**************************************************************************************
+
+#ifndef _BCMTAG_H_
+#define _BCMTAG_H_
+
+
+#define BCM_SIG_1 "Broadcom Corporation"
+#define BCM_SIG_2 "ver. 2.0" // was "firmware version 2.0" now it is split 6 char out for chip id.
+
+#define BCM_TAG_VER "6"
+#define BCM_TAG_VER_LAST "26"
+
+// file tag (head) structure all is in clear text except validationTokens (crc, md5, sha1, etc). Total: 128 unsigned chars
+#define TAG_LEN 256
+#define TAG_VER_LEN 4
+#define SIG_LEN 20
+#define SIG_LEN_2 14 // Original second SIG = 20 is now devided into 14 for SIG_LEN_2 and 6 for CHIP_ID
+#define CHIP_ID_LEN 6
+#define IMAGE_LEN 10
+#define ADDRESS_LEN 12
+#define FLAG_LEN 2
+#define TOKEN_LEN 20
+#define BOARD_ID_LEN 16
+#define RESERVED_LEN (TAG_LEN - TAG_VER_LEN - SIG_LEN - SIG_LEN_2 - CHIP_ID_LEN - BOARD_ID_LEN - \
+ (4*IMAGE_LEN) - (3*ADDRESS_LEN) - (3*FLAG_LEN) - (2*TOKEN_LEN))
+
+
+// TAG for downloadable image (kernel plus file system)
+typedef struct _FILE_TAG
+{
+ unsigned char tagVersion[TAG_VER_LEN]; // tag version. Will be 2 here.
+ unsigned char signiture_1[SIG_LEN]; // text line for company info
+ unsigned char signiture_2[SIG_LEN_2]; // additional info (can be version number)
+ unsigned char chipId[CHIP_ID_LEN]; // chip id
+ unsigned char boardId[BOARD_ID_LEN]; // board id
+ unsigned char bigEndian[FLAG_LEN]; // if = 1 - big, = 0 - little endia of the host
+ unsigned char totalImageLen[IMAGE_LEN]; // the sum of all the following length
+ unsigned char cfeAddress[ADDRESS_LEN]; // if non zero, cfe starting address
+ unsigned char cfeLen[IMAGE_LEN]; // if non zero, cfe size in clear ASCII text.
+ unsigned char rootfsAddress[ADDRESS_LEN]; // if non zero, filesystem starting address
+ unsigned char rootfsLen[IMAGE_LEN]; // if non zero, filesystem size in clear ASCII text.
+ unsigned char kernelAddress[ADDRESS_LEN]; // if non zero, kernel starting address
+ unsigned char kernelLen[IMAGE_LEN]; // if non zero, kernel size in clear ASCII text.
+ unsigned char dualImage[FLAG_LEN]; // if 1, dual image
+ unsigned char inactiveLen[FLAG_LEN]; // if 1, the image is INACTIVE; if 0, active
+ unsigned char reserved[RESERVED_LEN]; // reserved for later use
+ unsigned char imageValidationToken[TOKEN_LEN];// image validation token - can be crc, md5, sha; for
+ // now will be 4 unsigned char crc
+ unsigned char tagValidationToken[TOKEN_LEN]; // validation token for tag(from signiture_1 to end of // mageValidationToken)
+} FILE_TAG, *PFILE_TAG;
+
+#define CRC32_INIT_VALUE 0xffffffff /* Initial CRC32 checksum value */
+#define CRC_LEN 4
+
+// only included if for bcmTag.exe program
+#ifdef BCMTAG_EXE_USE
+
+static unsigned long Crc32_table[256] = {
+ 0x00000000, 0x77073096, 0xEE0E612C, 0x990951BA,
+ 0x076DC419, 0x706AF48F, 0xE963A535, 0x9E6495A3,
+ 0x0EDB8832, 0x79DCB8A4, 0xE0D5E91E, 0x97D2D988,
+ 0x09B64C2B, 0x7EB17CBD, 0xE7B82D07, 0x90BF1D91,
+ 0x1DB71064, 0x6AB020F2, 0xF3B97148, 0x84BE41DE,
+ 0x1ADAD47D, 0x6DDDE4EB, 0xF4D4B551, 0x83D385C7,
+ 0x136C9856, 0x646BA8C0, 0xFD62F97A, 0x8A65C9EC,
+ 0x14015C4F, 0x63066CD9, 0xFA0F3D63, 0x8D080DF5,
+ 0x3B6E20C8, 0x4C69105E, 0xD56041E4, 0xA2677172,
+ 0x3C03E4D1, 0x4B04D447, 0xD20D85FD, 0xA50AB56B,
+ 0x35B5A8FA, 0x42B2986C, 0xDBBBC9D6, 0xACBCF940,
+ 0x32D86CE3, 0x45DF5C75, 0xDCD60DCF, 0xABD13D59,
+ 0x26D930AC, 0x51DE003A, 0xC8D75180, 0xBFD06116,
+ 0x21B4F4B5, 0x56B3C423, 0xCFBA9599, 0xB8BDA50F,
+ 0x2802B89E, 0x5F058808, 0xC60CD9B2, 0xB10BE924,
+ 0x2F6F7C87, 0x58684C11, 0xC1611DAB, 0xB6662D3D,
+ 0x76DC4190, 0x01DB7106, 0x98D220BC, 0xEFD5102A,
+ 0x71B18589, 0x06B6B51F, 0x9FBFE4A5, 0xE8B8D433,
+ 0x7807C9A2, 0x0F00F934, 0x9609A88E, 0xE10E9818,
+ 0x7F6A0DBB, 0x086D3D2D, 0x91646C97, 0xE6635C01,
+ 0x6B6B51F4, 0x1C6C6162, 0x856530D8, 0xF262004E,
+ 0x6C0695ED, 0x1B01A57B, 0x8208F4C1, 0xF50FC457,
+ 0x65B0D9C6, 0x12B7E950, 0x8BBEB8EA, 0xFCB9887C,
+ 0x62DD1DDF, 0x15DA2D49, 0x8CD37CF3, 0xFBD44C65,
+ 0x4DB26158, 0x3AB551CE, 0xA3BC0074, 0xD4BB30E2,
+ 0x4ADFA541, 0x3DD895D7, 0xA4D1C46D, 0xD3D6F4FB,
+ 0x4369E96A, 0x346ED9FC, 0xAD678846, 0xDA60B8D0,
+ 0x44042D73, 0x33031DE5, 0xAA0A4C5F, 0xDD0D7CC9,
+ 0x5005713C, 0x270241AA, 0xBE0B1010, 0xC90C2086,
+ 0x5768B525, 0x206F85B3, 0xB966D409, 0xCE61E49F,
+ 0x5EDEF90E, 0x29D9C998, 0xB0D09822, 0xC7D7A8B4,
+ 0x59B33D17, 0x2EB40D81, 0xB7BD5C3B, 0xC0BA6CAD,
+ 0xEDB88320, 0x9ABFB3B6, 0x03B6E20C, 0x74B1D29A,
+ 0xEAD54739, 0x9DD277AF, 0x04DB2615, 0x73DC1683,
+ 0xE3630B12, 0x94643B84, 0x0D6D6A3E, 0x7A6A5AA8,
+ 0xE40ECF0B, 0x9309FF9D, 0x0A00AE27, 0x7D079EB1,
+ 0xF00F9344, 0x8708A3D2, 0x1E01F268, 0x6906C2FE,
+ 0xF762575D, 0x806567CB, 0x196C3671, 0x6E6B06E7,
+ 0xFED41B76, 0x89D32BE0, 0x10DA7A5A, 0x67DD4ACC,
+ 0xF9B9DF6F, 0x8EBEEFF9, 0x17B7BE43, 0x60B08ED5,
+ 0xD6D6A3E8, 0xA1D1937E, 0x38D8C2C4, 0x4FDFF252,
+ 0xD1BB67F1, 0xA6BC5767, 0x3FB506DD, 0x48B2364B,
+ 0xD80D2BDA, 0xAF0A1B4C, 0x36034AF6, 0x41047A60,
+ 0xDF60EFC3, 0xA867DF55, 0x316E8EEF, 0x4669BE79,
+ 0xCB61B38C, 0xBC66831A, 0x256FD2A0, 0x5268E236,
+ 0xCC0C7795, 0xBB0B4703, 0x220216B9, 0x5505262F,
+ 0xC5BA3BBE, 0xB2BD0B28, 0x2BB45A92, 0x5CB36A04,
+ 0xC2D7FFA7, 0xB5D0CF31, 0x2CD99E8B, 0x5BDEAE1D,
+ 0x9B64C2B0, 0xEC63F226, 0x756AA39C, 0x026D930A,
+ 0x9C0906A9, 0xEB0E363F, 0x72076785, 0x05005713,
+ 0x95BF4A82, 0xE2B87A14, 0x7BB12BAE, 0x0CB61B38,
+ 0x92D28E9B, 0xE5D5BE0D, 0x7CDCEFB7, 0x0BDBDF21,
+ 0x86D3D2D4, 0xF1D4E242, 0x68DDB3F8, 0x1FDA836E,
+ 0x81BE16CD, 0xF6B9265B, 0x6FB077E1, 0x18B74777,
+ 0x88085AE6, 0xFF0F6A70, 0x66063BCA, 0x11010B5C,
+ 0x8F659EFF, 0xF862AE69, 0x616BFFD3, 0x166CCF45,
+ 0xA00AE278, 0xD70DD2EE, 0x4E048354, 0x3903B3C2,
+ 0xA7672661, 0xD06016F7, 0x4969474D, 0x3E6E77DB,
+ 0xAED16A4A, 0xD9D65ADC, 0x40DF0B66, 0x37D83BF0,
+ 0xA9BCAE53, 0xDEBB9EC5, 0x47B2CF7F, 0x30B5FFE9,
+ 0xBDBDF21C, 0xCABAC28A, 0x53B39330, 0x24B4A3A6,
+ 0xBAD03605, 0xCDD70693, 0x54DE5729, 0x23D967BF,
+ 0xB3667A2E, 0xC4614AB8, 0x5D681B02, 0x2A6F2B94,
+ 0xB40BBE37, 0xC30C8EA1, 0x5A05DF1B, 0x2D02EF8D
+};
+#endif // BCMTAG_USE
+
+
+#endif // _BCMTAG_H_
+
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2003 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+
+#ifndef __BCM_INTR_H
+#define __BCM_INTR_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+#if defined(CONFIG_BCM96338)
+#include <6338_intr.h>
+#endif
+#if defined(CONFIG_BCM96345)
+#include <6345_intr.h>
+#endif
+#if defined(CONFIG_BCM96348)
+#include <6348_intr.h>
+#endif
+
+/* defines */
+struct pt_regs;
+typedef int (*FN_HANDLER) (int, void *);
+
+/* prototypes */
+extern void enable_brcm_irq(unsigned int irq);
+extern void disable_brcm_irq(unsigned int irq);
+extern int request_external_irq(unsigned int irq,
+ FN_HANDLER handler, unsigned long irqflags,
+ const char * devname, void *dev_id);
+extern unsigned int BcmHalMapInterrupt(FN_HANDLER isr, unsigned int param,
+ unsigned int interruptId);
+extern void dump_intr_regs(void);
+
+/* compatibility definitions */
+#define BcmHalInterruptEnable(irq) enable_brcm_irq( irq )
+#define BcmHalInterruptDisable(irq) disable_brcm_irq( irq )
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2004 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+
+#ifndef __BCM_MAP_PART_H
+#define __BCM_MAP_PART_H
+
+#if defined(CONFIG_BCM96338)
+#include <6338_map_part.h>
+#endif
+#if defined(CONFIG_BCM96345)
+#include <6345_map_part.h>
+#endif
+#if defined(CONFIG_BCM96348)
+#include <6348_map_part.h>
+#endif
+
+#endif
+
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2004 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+
+//
+// bcmpci.h - bcm96348 PCI, Cardbus, and PCMCIA definition
+//
+#ifndef BCMPCI_H
+#define BCMPCI_H
+
+/* Memory window in internal system bus address space */
+#define BCM_PCI_MEM_BASE 0x08000000
+/* IO window in internal system bus address space */
+#define BCM_PCI_IO_BASE 0x0C000000
+
+#define BCM_PCI_ADDR_MASK 0x1fffffff
+
+/* Memory window size (range) */
+#define BCM_PCI_MEM_SIZE_16MB 0x01000000
+/* IO window size (range) */
+#define BCM_PCI_IO_SIZE_64KB 0x00010000
+
+/* PCI Configuration and I/O space acesss */
+#define BCM_PCI_CFG(d, f, o) ( (d << 11) | (f << 8) | (o/4 << 2) )
+
+/* fake USB PCI slot */
+#define USB_HOST_SLOT 9
+#define USB_BAR0_MEM_SIZE 0x0800
+
+#define BCM_HOST_MEM_SPACE1 0x10000000
+#define BCM_HOST_MEM_SPACE2 0x00000000
+
+/*
+ * EBI bus clock is 33MHz and share with PCI bus
+ * each clock cycle is 30ns.
+ */
+/* attribute memory access wait cnt for 4306 */
+#define PCMCIA_ATTR_CE_HOLD 3 // data hold time 70ns
+#define PCMCIA_ATTR_CE_SETUP 3 // data setup time 50ns
+#define PCMCIA_ATTR_INACTIVE 6 // time between read/write cycles 180ns. For the total cycle time 600ns (cnt1+cnt2+cnt3+cnt4)
+#define PCMCIA_ATTR_ACTIVE 10 // OE/WE pulse width 300ns
+
+/* common memory access wait cnt for 4306 */
+#define PCMCIA_MEM_CE_HOLD 1 // data hold time 30ns
+#define PCMCIA_MEM_CE_SETUP 1 // data setup time 30ns
+#define PCMCIA_MEM_INACTIVE 2 // time between read/write cycles 40ns. For the total cycle time 250ns (cnt1+cnt2+cnt3+cnt4)
+#define PCMCIA_MEM_ACTIVE 5 // OE/WE pulse width 150ns
+
+#define PCCARD_VCC_MASK 0x00070000 // Mask Reset also
+#define PCCARD_VCC_33V 0x00010000
+#define PCCARD_VCC_50V 0x00020000
+
+typedef enum {
+ MPI_CARDTYPE_NONE, // No Card in slot
+ MPI_CARDTYPE_PCMCIA, // 16-bit PCMCIA card in slot
+ MPI_CARDTYPE_CARDBUS, // 32-bit CardBus card in slot
+} CardType;
+
+#define CARDBUS_SLOT 0 // Slot 0 is default for CardBus
+
+#define pcmciaAttrOffset 0x00200000
+#define pcmciaMemOffset 0x00000000
+// Needs to be right above PCI I/O space. Give 0x8000 (32K) to PCMCIA.
+#define pcmciaIoOffset (BCM_PCI_IO_BASE + 0x80000)
+// Base Address is that mapped into the MPI ChipSelect registers.
+// UBUS bridge MemoryWindow 0 outputs a 0x00 for the base.
+#define pcmciaBase 0xbf000000
+#define pcmciaAttr (pcmciaAttrOffset | pcmciaBase)
+#define pcmciaMem (pcmciaMemOffset | pcmciaBase)
+#define pcmciaIo (pcmciaIoOffset | pcmciaBase)
+
+#endif
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2002 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+
+//
+// bcmtypes.h - misc useful typedefs
+//
+#ifndef BCMTYPES_H
+#define BCMTYPES_H
+
+// These are also defined in typedefs.h in the application area, so I need to
+// protect against re-definition.
+
+#ifndef _TYPEDEFS_H_
+typedef unsigned char uint8;
+typedef unsigned short uint16;
+typedef unsigned long uint32;
+typedef signed char int8;
+typedef signed short int16;
+typedef signed long int32;
+#endif
+
+typedef unsigned char byte;
+// typedef unsigned long sem_t;
+
+typedef unsigned long HANDLE,*PULONG,DWORD,*PDWORD;
+typedef signed long LONG,*PLONG;
+
+typedef unsigned int *PUINT;
+typedef signed int INT;
+
+typedef unsigned short *PUSHORT;
+typedef signed short SHORT,*PSHORT;
+typedef unsigned short WORD,*PWORD;
+
+typedef unsigned char *PUCHAR;
+typedef signed char *PCHAR;
+
+typedef void *PVOID;
+
+typedef unsigned char BOOLEAN, *PBOOL, *PBOOLEAN;
+
+typedef unsigned char BYTE,*PBYTE;
+
+//#ifndef __GNUC__
+//The following has been defined in Vxworks internally: vxTypesOld.h
+//redefine under vxworks will cause error
+typedef signed int *PINT;
+
+typedef signed char INT8;
+typedef signed short INT16;
+typedef signed long INT32;
+
+typedef unsigned char UINT8;
+typedef unsigned short UINT16;
+typedef unsigned long UINT32;
+
+typedef unsigned char UCHAR;
+typedef unsigned short USHORT;
+typedef unsigned int UINT;
+typedef unsigned long ULONG;
+
+typedef void VOID;
+typedef unsigned char BOOL;
+
+//#endif /* __GNUC__ */
+
+
+// These are also defined in typedefs.h in the application area, so I need to
+// protect against re-definition.
+#ifndef TYPEDEFS_H
+
+// Maximum and minimum values for a signed 16 bit integer.
+#define MAX_INT16 32767
+#define MIN_INT16 -32768
+
+// Useful for true/false return values. This uses the
+// Taligent notation (k for constant).
+typedef enum
+{
+ kFalse = 0,
+ kTrue = 1
+} Bool;
+
+#endif
+
+/* macros to protect against unaligned accesses */
+
+#if 0
+/* first arg is an address, second is a value */
+#define PUT16( a, d ) { \
+ *((byte *)a) = (byte)((d)>>8); \
+ *(((byte *)a)+1) = (byte)(d); \
+}
+
+#define PUT32( a, d ) { \
+ *((byte *)a) = (byte)((d)>>24); \
+ *(((byte *)a)+1) = (byte)((d)>>16); \
+ *(((byte *)a)+2) = (byte)((d)>>8); \
+ *(((byte *)a)+3) = (byte)(d); \
+}
+
+/* first arg is an address, returns a value */
+#define GET16( a ) ( \
+ (*((byte *)a) << 8) | \
+ (*(((byte *)a)+1)) \
+)
+
+#define GET32( a ) ( \
+ (*((byte *)a) << 24) | \
+ (*(((byte *)a)+1) << 16) | \
+ (*(((byte *)a)+2) << 8) | \
+ (*(((byte *)a)+3)) \
+)
+#endif
+
+#ifndef YES
+#define YES 1
+#endif
+
+#ifndef NO
+#define NO 0
+#endif
+
+#ifndef IN
+#define IN
+#endif
+
+#ifndef OUT
+#define OUT
+#endif
+
+#ifndef TRUE
+#define TRUE 1
+#endif
+
+#ifndef FALSE
+#define FALSE 0
+#endif
+
+#define READ32(addr) (*(volatile UINT32 *)((ULONG)&addr))
+#define READ16(addr) (*(volatile UINT16 *)((ULONG)&addr))
+#define READ8(addr) (*(volatile UINT8 *)((ULONG)&addr))
+
+#endif
--- /dev/null
+/*
+<:copyright-gpl
+ Copyright 2002 Broadcom Corp. All Rights Reserved.
+
+ This program is free software; you can distribute it and/or modify it
+ under the terms of the GNU General Public License (Version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with this program; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+:>
+*/
+/***********************************************************************/
+/* */
+/* MODULE: board.h */
+/* DATE: 97/02/18 */
+/* PURPOSE: Board specific information. This module should include */
+/* all base device addresses and board specific macros. */
+/* */
+/***********************************************************************/
+#ifndef _BOARD_H
+#define _BOARD_H
+
+/*****************************************************************************/
+/* Misc board definitions */
+/*****************************************************************************/
+
+#define DYING_GASP_API
+
+/*****************************************************************************/
+/* Physical Memory Map */
+/*****************************************************************************/
+
+#define PHYS_DRAM_BASE 0x00000000 /* Dynamic RAM Base */
+#define PHYS_FLASH_BASE 0x1FC00000 /* Flash Memory */
+
+/*****************************************************************************/
+/* Note that the addresses above are physical addresses and that programs */
+/* have to use converted addresses defined below: */
+/*****************************************************************************/
+#define DRAM_BASE (0x80000000 | PHYS_DRAM_BASE) /* cached DRAM */
+#define DRAM_BASE_NOCACHE (0xA0000000 | PHYS_DRAM_BASE) /* uncached DRAM */
+#define FLASH_BASE (0xA0000000 | PHYS_FLASH_BASE) /* uncached Flash */
+
+/*****************************************************************************/
+/* Select the PLL value to get the desired CPU clock frequency. */
+/* */
+/* */
+/*****************************************************************************/
+#define FPERIPH 50000000
+
+#define ONEK 1024
+#define BLK64K (64*ONEK)
+#define FLASH45_BLKS_BOOT_ROM 1
+#define FLASH45_LENGTH_BOOT_ROM (FLASH45_BLKS_BOOT_ROM * BLK64K)
+#define FLASH_RESERVED_AT_END (64*ONEK) /*reserved for PSI, scratch pad*/
+
+/*****************************************************************************/
+/* Note that the addresses above are physical addresses and that programs */
+/* have to use converted addresses defined below: */
+/*****************************************************************************/
+#define DRAM_BASE (0x80000000 | PHYS_DRAM_BASE) /* cached DRAM */
+#define DRAM_BASE_NOCACHE (0xA0000000 | PHYS_DRAM_BASE) /* uncached DRAM */
+#define FLASH_BASE (0xA0000000 | PHYS_FLASH_BASE) /* uncached Flash */
+
+/*****************************************************************************/
+/* Select the PLL value to get the desired CPU clock frequency. */
+/* */
+/* */
+/*****************************************************************************/
+#define FPERIPH 50000000
+
+#define SDRAM_TYPE_ADDRESS_OFFSET 16
+#define NVRAM_DATA_OFFSET 0x0580
+#define NVRAM_DATA_ID 0x0f1e2d3c
+#define BOARD_SDRAM_TYPE *(unsigned long *) \
+ (FLASH_BASE + SDRAM_TYPE_ADDRESS_OFFSET)
+
+#define ONEK 1024
+#define BLK64K (64*ONEK)
+
+// nvram and psi flash definitions for 45
+#define FLASH45_LENGTH_NVRAM ONEK // 1k nvram
+#define NVRAM_PSI_DEFAULT 24 // default psi in K byes
+
+/*****************************************************************************/
+/* NVRAM Offset and definition */
+/*****************************************************************************/
+
+#define NVRAM_VERSION_NUMBER 2
+#define NVRAM_VERSION_NUMBER_ADDRESS 0
+
+#define NVRAM_BOOTLINE_LEN 256
+#define NVRAM_BOARD_ID_STRING_LEN 16
+#define NVRAM_MAC_ADDRESS_LEN 6
+#define NVRAM_MAC_COUNT_MAX 32
+
+/*****************************************************************************/
+/* Misc Offsets */
+/*****************************************************************************/
+
+#define CFE_VERSION_OFFSET 0x0570
+#define CFE_VERSION_MARK_SIZE 5
+#define CFE_VERSION_SIZE 5
+
+typedef struct
+{
+ unsigned long ulVersion;
+ char szBootline[NVRAM_BOOTLINE_LEN];
+ char szBoardId[NVRAM_BOARD_ID_STRING_LEN];
+ unsigned long ulReserved1[2];
+ unsigned long ulNumMacAddrs;
+ unsigned char ucaBaseMacAddr[NVRAM_MAC_ADDRESS_LEN];
+ char chReserved[2];
+ unsigned long ulCheckSum;
+} NVRAM_DATA, *PNVRAM_DATA;
+
+
+/*****************************************************************************/
+/* board ioctl calls for flash, led and some other utilities */
+/*****************************************************************************/
+
+
+/* Defines. for board driver */
+#define BOARD_IOCTL_MAGIC 'B'
+#define BOARD_DRV_MAJOR 206
+
+#define MAC_ADDRESS_ANY (unsigned long) -1
+
+#define BOARD_IOCTL_FLASH_INIT \
+ _IOWR(BOARD_IOCTL_MAGIC, 0, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_FLASH_WRITE \
+ _IOWR(BOARD_IOCTL_MAGIC, 1, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_FLASH_READ \
+ _IOWR(BOARD_IOCTL_MAGIC, 2, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_GET_NR_PAGES \
+ _IOWR(BOARD_IOCTL_MAGIC, 3, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_DUMP_ADDR \
+ _IOWR(BOARD_IOCTL_MAGIC, 4, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_SET_MEMORY \
+ _IOWR(BOARD_IOCTL_MAGIC, 5, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_MIPS_SOFT_RESET \
+ _IOWR(BOARD_IOCTL_MAGIC, 6, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_LED_CTRL \
+ _IOWR(BOARD_IOCTL_MAGIC, 7, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_GET_ID \
+ _IOWR(BOARD_IOCTL_MAGIC, 8, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_GET_MAC_ADDRESS \
+ _IOWR(BOARD_IOCTL_MAGIC, 9, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_RELEASE_MAC_ADDRESS \
+ _IOWR(BOARD_IOCTL_MAGIC, 10, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_GET_PSI_SIZE \
+ _IOWR(BOARD_IOCTL_MAGIC, 11, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_GET_SDRAM_SIZE \
+ _IOWR(BOARD_IOCTL_MAGIC, 12, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_SET_MONITOR_FD \
+ _IOWR(BOARD_IOCTL_MAGIC, 13, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_WAKEUP_MONITOR_TASK \
+ _IOWR(BOARD_IOCTL_MAGIC, 14, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_GET_BOOTLINE \
+ _IOWR(BOARD_IOCTL_MAGIC, 15, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_SET_BOOTLINE \
+ _IOWR(BOARD_IOCTL_MAGIC, 16, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_GET_BASE_MAC_ADDRESS \
+ _IOWR(BOARD_IOCTL_MAGIC, 17, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_GET_CHIP_ID \
+ _IOWR(BOARD_IOCTL_MAGIC, 18, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_GET_NUM_ENET \
+ _IOWR(BOARD_IOCTL_MAGIC, 19, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_GET_CFE_VER \
+ _IOWR(BOARD_IOCTL_MAGIC, 20, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_GET_ENET_CFG \
+ _IOWR(BOARD_IOCTL_MAGIC, 21, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_GET_WLAN_ANT_INUSE \
+ _IOWR(BOARD_IOCTL_MAGIC, 22, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_SET_TRIGGER_EVENT \
+ _IOWR(BOARD_IOCTL_MAGIC, 23, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_GET_TRIGGER_EVENT \
+ _IOWR(BOARD_IOCTL_MAGIC, 24, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_UNSET_TRIGGER_EVENT \
+ _IOWR(BOARD_IOCTL_MAGIC, 25, BOARD_IOCTL_PARMS)
+
+#define BOARD_IOCTL_SET_SES_LED \
+ _IOWR(BOARD_IOCTL_MAGIC, 26, BOARD_IOCTL_PARMS)
+
+//<<JUNHON, 2004/09/15, get reset button status , tim hou , 05/04/12
+#define RESET_BUTTON_UP 1
+#define RESET_BUTTON_PRESSDOWN 0
+#define BOARD_IOCTL_GET_RESETHOLD \
+ _IOWR(BOARD_IOCTL_MAGIC, 27, BOARD_IOCTL_PARMS)
+//>>JUNHON, 2004/09/15
+
+// for the action in BOARD_IOCTL_PARMS for flash operation
+typedef enum
+{
+ PERSISTENT,
+ NVRAM,
+ BCM_IMAGE_CFE,
+ BCM_IMAGE_FS,
+ BCM_IMAGE_KERNEL,
+ BCM_IMAGE_WHOLE,
+ SCRATCH_PAD,
+ FLASH_SIZE,
+} BOARD_IOCTL_ACTION;
+
+
+typedef struct boardIoctParms
+{
+ char *string;
+ char *buf;
+ int strLen;
+ int offset;
+ BOARD_IOCTL_ACTION action; /* flash read/write: nvram, persistent, bcm image */
+ int result;
+} BOARD_IOCTL_PARMS;
+
+
+// LED defines
+typedef enum
+{
+ kLedAdsl,
+ kLedWireless,
+ kLedUsb,
+ kLedHpna,
+ kLedWanData,
+ kLedPPP,
+ kLedVoip,
+ kLedSes,
+ kLedLan,
+ kLedSelfTest,
+ kLedEnd, // NOTE: Insert the new led name before this one. Alway stay at the end.
+} BOARD_LED_NAME;
+
+typedef enum
+{
+ kLedStateOff, /* turn led off */
+ kLedStateOn, /* turn led on */
+ kLedStateFail, /* turn led on red */
+ kLedStateBlinkOnce, /* blink once, ~100ms and ignore the same call during the 100ms period */
+ kLedStateSlowBlinkContinues, /* slow blink continues at ~600ms interval */
+ kLedStateFastBlinkContinues, /* fast blink continues at ~200ms interval */
+} BOARD_LED_STATE;
+
+
+// virtual and physical map pair defined in board.c
+typedef struct ledmappair
+{
+ BOARD_LED_NAME ledName; // virtual led name
+ BOARD_LED_STATE ledInitState; // initial led state when the board boots.
+ unsigned short ledMask; // physical GPIO pin mask
+ unsigned short ledActiveLow; // reset bit to turn on LED
+ unsigned short ledMaskFail; // physical GPIO pin mask for state failure
+ unsigned short ledActiveLowFail;// reset bit to turn on LED
+} LED_MAP_PAIR, *PLED_MAP_PAIR;
+
+typedef void (*HANDLE_LED_FUNC)(BOARD_LED_NAME ledName, BOARD_LED_STATE ledState);
+
+/* Flash storage address information that is determined by the flash driver. */
+typedef struct flashaddrinfo
+{
+ int flash_persistent_start_blk;
+ int flash_persistent_number_blk;
+ int flash_persistent_length;
+ unsigned long flash_persistent_blk_offset;
+ int flash_scratch_pad_start_blk; // start before psi (SP_BUF_LEN)
+ int flash_scratch_pad_number_blk;
+ int flash_scratch_pad_length;
+ unsigned long flash_scratch_pad_blk_offset;
+ int flash_nvram_start_blk;
+ int flash_nvram_number_blk;
+ int flash_nvram_length;
+ unsigned long flash_nvram_blk_offset;
+} FLASH_ADDR_INFO, *PFLASH_ADDR_INFO;
+
+// scratch pad defines
+/* SP - Persisten Scratch Pad format:
+ sp header : 32 bytes
+ tokenId-1 : 8 bytes
+ tokenId-1 len : 4 bytes
+ tokenId-1 data
+ ....
+ tokenId-n : 8 bytes
+ tokenId-n len : 4 bytes
+ tokenId-n data
+*/
+
+#define MAGIC_NUM_LEN 8
+#define MAGIC_NUMBER "gOGoBrCm"
+#define TOKEN_NAME_LEN 16
+#define SP_VERSION 1
+#define SP_MAX_LEN 8 * 1024 // 8k buf before psi
+#define SP_RESERVERD 16
+
+typedef struct _SP_HEADER
+{
+ char SPMagicNum[MAGIC_NUM_LEN]; // 8 bytes of magic number
+ int SPVersion; // version number
+ int SPUsedLen; // used sp len
+ char SPReserved[SP_RESERVERD]; // reservied, total 32 bytes
+} SP_HEADER, *PSP_HEADER;
+
+typedef struct _TOKEN_DEF
+{
+ char tokenName[TOKEN_NAME_LEN];
+ int tokenLen;
+} SP_TOKEN, *PSP_TOKEN;
+
+
+/*****************************************************************************/
+/* Function Prototypes */
+/*****************************************************************************/
+#if !defined(__ASM_ASM_H)
+void dumpaddr( unsigned char *pAddr, int nLen );
+
+int kerSysNvRamGet(char *string, int strLen, int offset);
+int kerSysNvRamSet(char *string, int strLen, int offset);
+int kerSysPersistentGet(char *string, int strLen, int offset);
+int kerSysPersistentSet(char *string, int strLen, int offset);
+int kerSysScratchPadGet(char *tokName, char *tokBuf, int tokLen);
+int kerSysScratchPadSet(char *tokName, char *tokBuf, int tokLen);
+int kerSysBcmImageSet( int flash_start_addr, char *string, int size);
+int kerSysGetMacAddress( unsigned char *pucaAddr, unsigned long ulId );
+int kerSysReleaseMacAddress( unsigned char *pucaAddr );
+int kerSysGetSdramSize( void );
+void kerSysGetBootline(char *string, int strLen);
+void kerSysSetBootline(char *string, int strLen);
+void kerSysMipsSoftReset(void);
+void kerSysLedCtrl(BOARD_LED_NAME, BOARD_LED_STATE);
+void kerSysLedRegisterHwHandler( BOARD_LED_NAME, HANDLE_LED_FUNC, int );
+int kerSysFlashSizeGet(void);
+void kerSysRegisterDyingGaspHandler(char *devname, void *cbfn, void *context);
+void kerSysDeregisterDyingGaspHandler(char *devname);
+void kerSysWakeupMonitorTask( void );
+#endif
+
+#define BOOT_CFE 0
+#define BOOT_REDBOOT 1
+
+extern int boot_loader_type;
+
+#endif /* _BOARD_H */
+
--- /dev/null
+#define ADSL_SDRAM_IMAGE_SIZE (384*1024)
+
+#define BOOT_LOADER_UNKNOWN 0
+#define BOOT_LOADER_CFE 1
+#define BOOT_LOADER_REDBOOT 2
+#define BOOT_LOADER_CFE2 3
+#define BOOT_LOADER_LAST 3
--- /dev/null
+#ifndef __ASM_MACH_BCM963XX_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_BCM963XX_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_tlb 1
+#define cpu_has_4kex 4
+#define cpu_has_4ktlb 8
+#define cpu_has_fpu 0
+#define cpu_has_32fpr 0
+#define cpu_has_counter 0x40
+#define cpu_has_watch 0
+#define cpu_has_mips16 0
+#define cpu_has_divec 0x200
+#define cpu_has_vce 0
+#define cpu_has_cache_cdex_p 0
+#define cpu_has_cache_cdex_s 0
+#define cpu_has_prefetch 0x40000
+#define cpu_has_mcheck 0x2000
+#define cpu_has_ejtag 0x4000
+#define cpu_has_llsc 0x10000
+#define cpu_has_vtag_icache 0
+#define cpu_has_dc_aliases 0
+#define cpu_has_ic_fills_f_dc 0
+
+#define cpu_has_nofpuex 0
+#define cpu_has_64bits 0
+#define cpu_has_64bit_zero_reg 0
+#define cpu_has_64bit_gp_regs 0
+#define cpu_has_64bit_addresses 0
+
+#define cpu_has_subset_pcaches 0
+
+#define cpu_dcache_line_size() 16
+#define cpu_icache_line_size() 16
+#define cpu_scache_line_size() 0
+
+#endif /* __ASM_MACH_BCM963XX_CPU_FEATURE_OVERRIDES_H */
--- /dev/null
+/*
+ * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __NVRAM_H
+#define __NVRAM_H
+
+struct nvram_header {
+ u32 magic;
+ u32 len;
+ u32 crc_ver_init; /* 0:7 crc, 8:15 ver, 16:31 sdram_init */
+ u32 config_refresh; /* 0:15 sdram_config, 16:31 sdram_refresh */
+ u32 config_ncdl; /* ncdl values for memc */
+};
+
+struct nvram_tuple {
+ char *name;
+ char *value;
+ struct nvram_tuple *next;
+};
+
+#define NVRAM_HEADER 0x48534C46 /* 'FLSH' */
+#define NVRAM_VERSION 1
+#define NVRAM_HEADER_SIZE 20
+#define NVRAM_SPACE 0x8000
+
+#define NVRAM_MAX_VALUE_LEN 255
+#define NVRAM_MAX_PARAM_LEN 64
+
+char *nvram_get(const char *name);
+
+#endif
--- /dev/null
+#ifndef _LINUX_ATMRT2684_H
+#define _LINUX_ATMRT2684_H
+
+#include <linux/atm.h>
+#include <linux/if.h> /* For IFNAMSIZ */
+
+#define RT2684_ENCAPS_NULL (0) /* VC-mux */
+#define RT2684_ENCAPS_LLC (1)
+#define RT2684_ENCAPS_AUTODETECT (2) /* Unsuported */
+
+/*
+ * This is for the ATM_NEWBACKENDIF call - these are like socket families:
+ * the first element of the structure is the backend number and the rest
+ * is per-backend specific
+ */
+struct atm_newif_rt2684 {
+ atm_backend_t backend_num; /* ATM_BACKEND_RT2684 */
+ char ifname[IFNAMSIZ];
+};
+
+/*
+ * This structure is used to specify a rt2684 interface - either by a
+ * positive integer (returned by ATM_NEWBACKENDIF) or the interfaces name
+ */
+#define RT2684_FIND_BYNOTHING (0)
+#define RT2684_FIND_BYNUM (1)
+#define RT2684_FIND_BYIFNAME (2)
+struct rt2684_if_spec {
+ int method; /* RT2684_FIND_* */
+ union {
+ char ifname[IFNAMSIZ];
+ int devnum;
+ } spec;
+};
+
+/*
+ * This is for the ATM_SETBACKEND call - these are like socket families:
+ * the first element of the structure is the backend number and the rest
+ * is per-backend specific
+ */
+struct atm_backend_rt2684 {
+ atm_backend_t backend_num; /* ATM_BACKEND_RT2684 */
+ struct rt2684_if_spec ifspec;
+ unsigned char encaps; /* RT2684_ENCAPS_* */
+};
+
+
+#endif /* _LINUX_ATMRT2684_H */
--- /dev/null
+#
+# Copyright (C) 2006 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+include $(TOPDIR)/rules.mk
+include $(INCLUDE_DIR)/image.mk
+
+LOADADDR = 0x8108c8f4 # RAM start + 16M
+KERNEL_ENTRY = 0x80100000 # Default kernel entry in arch/mips/Makefile
+RAMSIZE = 0x01000000 # 64MB
+
+LOADER_MAKEOPTS= \
+ KDIR=$(KDIR) \
+ LOADADDR=$(LOADADDR) \
+ KERNEL_ENTRY=$(KERNEL_ENTRY) \
+ RAMSIZE=$(RAMSIZE)
+
+define trxalign/jffs2-128k
+-a 0x20000
+endef
+define trxalign/jffs2-64k
+-a 0x10000
+endef
+define trxalign/squashfs
+-a 1024
+endef
+
+define Build/Clean
+ $(MAKE) -C lzma-loader clean
+endef
+
+define Image/Prepare
+ cat $(KDIR)/vmlinux | $(STAGING_DIR)/bin/lzma e -si -so -eos -lc1 -lp2 -pb2 > $(KDIR)/vmlinux.lzma
+ rm -f $(KDIR)/loader.gz
+ $(MAKE) -C lzma-loader \
+ BUILD_DIR="$(KDIR)" \
+ TARGET="$(KDIR)" \
+ clean install
+ echo -ne "\\x00" >> $(KDIR)/loader.gz
+endef
+
+define Image/Build
+ $(STAGING_DIR)/bin/trx -o $(BIN_DIR)/openwrt-$(BOARD)-$(KERNEL)-$(1).trx -f $(KDIR)/loader.gz -f $(KDIR)/vmlinux.lzma $(call trxalign/$(1)) -f $(KDIR)/root.$(1)
+endef
+
+$(eval $(call BuildImage))
--- /dev/null
+#
+# Copyright (C) 2006 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+# $Id: Makefile 6896 2007-04-08 17:20:01Z florian $
+
+include $(TOPDIR)/rules.mk
+
+PKG_NAME := lzma-loader
+PKG_BUILD_DIR := $(BUILD_DIR)/$(PKG_NAME)
+
+$(PKG_BUILD_DIR)/.prepared:
+ mkdir $(PKG_BUILD_DIR)
+ $(CP) ./src/* $(PKG_BUILD_DIR)/
+ touch $@
+
+$(PKG_BUILD_DIR)/loader.gz: $(PKG_BUILD_DIR)/.prepared
+ $(MAKE) -C $(PKG_BUILD_DIR) CC="$(TARGET_CC)" \
+ LD="$(TARGET_CROSS)ld" CROSS_COMPILE="$(TARGET_CROSS)"
+
+download:
+prepare: $(PKG_BUILD_DIR)/.prepared
+compile: $(PKG_BUILD_DIR)/loader.gz
+install:
+
+ifneq ($(TARGET),)
+install: compile
+ $(CP) $(PKG_BUILD_DIR)/loader.gz $(PKG_BUILD_DIR)/loader.elf $(TARGET)/
+endif
+
+clean:
+ rm -rf $(PKG_BUILD_DIR)
--- /dev/null
+/*
+ LzmaDecode.c
+ LZMA Decoder
+
+ LZMA SDK 4.05 Copyright (c) 1999-2004 Igor Pavlov (2004-08-25)
+ http://www.7-zip.org/
+
+ LZMA SDK is licensed under two licenses:
+ 1) GNU Lesser General Public License (GNU LGPL)
+ 2) Common Public License (CPL)
+ It means that you can select one of these two licenses and
+ follow rules of that license.
+
+ SPECIAL EXCEPTION:
+ Igor Pavlov, as the author of this code, expressly permits you to
+ statically or dynamically link your code (or bind by name) to the
+ interfaces of this file without subjecting your linked code to the
+ terms of the CPL or GNU LGPL. Any modifications or additions
+ to this file, however, are subject to the LGPL or CPL terms.
+*/
+
+#include "LzmaDecode.h"
+
+#ifndef Byte
+#define Byte unsigned char
+#endif
+
+#define kNumTopBits 24
+#define kTopValue ((UInt32)1 << kNumTopBits)
+
+#define kNumBitModelTotalBits 11
+#define kBitModelTotal (1 << kNumBitModelTotalBits)
+#define kNumMoveBits 5
+
+typedef struct _CRangeDecoder
+{
+ Byte *Buffer;
+ Byte *BufferLim;
+ UInt32 Range;
+ UInt32 Code;
+ #ifdef _LZMA_IN_CB
+ ILzmaInCallback *InCallback;
+ int Result;
+ #endif
+ int ExtraBytes;
+} CRangeDecoder;
+
+Byte RangeDecoderReadByte(CRangeDecoder *rd)
+{
+ if (rd->Buffer == rd->BufferLim)
+ {
+ #ifdef _LZMA_IN_CB
+ UInt32 size;
+ rd->Result = rd->InCallback->Read(rd->InCallback, &rd->Buffer, &size);
+ rd->BufferLim = rd->Buffer + size;
+ if (size == 0)
+ #endif
+ {
+ rd->ExtraBytes = 1;
+ return 0xFF;
+ }
+ }
+ return (*rd->Buffer++);
+}
+
+/* #define ReadByte (*rd->Buffer++) */
+#define ReadByte (RangeDecoderReadByte(rd))
+
+void RangeDecoderInit(CRangeDecoder *rd,
+ #ifdef _LZMA_IN_CB
+ ILzmaInCallback *inCallback
+ #else
+ Byte *stream, UInt32 bufferSize
+ #endif
+ )
+{
+ int i;
+ #ifdef _LZMA_IN_CB
+ rd->InCallback = inCallback;
+ rd->Buffer = rd->BufferLim = 0;
+ #else
+ rd->Buffer = stream;
+ rd->BufferLim = stream + bufferSize;
+ #endif
+ rd->ExtraBytes = 0;
+ rd->Code = 0;
+ rd->Range = (0xFFFFFFFF);
+ for(i = 0; i < 5; i++)
+ rd->Code = (rd->Code << 8) | ReadByte;
+}
+
+#define RC_INIT_VAR UInt32 range = rd->Range; UInt32 code = rd->Code;
+#define RC_FLUSH_VAR rd->Range = range; rd->Code = code;
+#define RC_NORMALIZE if (range < kTopValue) { range <<= 8; code = (code << 8) | ReadByte; }
+
+UInt32 RangeDecoderDecodeDirectBits(CRangeDecoder *rd, int numTotalBits)
+{
+ RC_INIT_VAR
+ UInt32 result = 0;
+ int i;
+ for (i = numTotalBits; i > 0; i--)
+ {
+ /* UInt32 t; */
+ range >>= 1;
+
+ result <<= 1;
+ if (code >= range)
+ {
+ code -= range;
+ result |= 1;
+ }
+ /*
+ t = (code - range) >> 31;
+ t &= 1;
+ code -= range & (t - 1);
+ result = (result + result) | (1 - t);
+ */
+ RC_NORMALIZE
+ }
+ RC_FLUSH_VAR
+ return result;
+}
+
+int RangeDecoderBitDecode(CProb *prob, CRangeDecoder *rd)
+{
+ UInt32 bound = (rd->Range >> kNumBitModelTotalBits) * *prob;
+ if (rd->Code < bound)
+ {
+ rd->Range = bound;
+ *prob += (kBitModelTotal - *prob) >> kNumMoveBits;
+ if (rd->Range < kTopValue)
+ {
+ rd->Code = (rd->Code << 8) | ReadByte;
+ rd->Range <<= 8;
+ }
+ return 0;
+ }
+ else
+ {
+ rd->Range -= bound;
+ rd->Code -= bound;
+ *prob -= (*prob) >> kNumMoveBits;
+ if (rd->Range < kTopValue)
+ {
+ rd->Code = (rd->Code << 8) | ReadByte;
+ rd->Range <<= 8;
+ }
+ return 1;
+ }
+}
+
+#define RC_GET_BIT2(prob, mi, A0, A1) \
+ UInt32 bound = (range >> kNumBitModelTotalBits) * *prob; \
+ if (code < bound) \
+ { A0; range = bound; *prob += (kBitModelTotal - *prob) >> kNumMoveBits; mi <<= 1; } \
+ else \
+ { A1; range -= bound; code -= bound; *prob -= (*prob) >> kNumMoveBits; mi = (mi + mi) + 1; } \
+ RC_NORMALIZE
+
+#define RC_GET_BIT(prob, mi) RC_GET_BIT2(prob, mi, ; , ;)
+
+int RangeDecoderBitTreeDecode(CProb *probs, int numLevels, CRangeDecoder *rd)
+{
+ int mi = 1;
+ int i;
+ #ifdef _LZMA_LOC_OPT
+ RC_INIT_VAR
+ #endif
+ for(i = numLevels; i > 0; i--)
+ {
+ #ifdef _LZMA_LOC_OPT
+ CProb *prob = probs + mi;
+ RC_GET_BIT(prob, mi)
+ #else
+ mi = (mi + mi) + RangeDecoderBitDecode(probs + mi, rd);
+ #endif
+ }
+ #ifdef _LZMA_LOC_OPT
+ RC_FLUSH_VAR
+ #endif
+ return mi - (1 << numLevels);
+}
+
+int RangeDecoderReverseBitTreeDecode(CProb *probs, int numLevels, CRangeDecoder *rd)
+{
+ int mi = 1;
+ int i;
+ int symbol = 0;
+ #ifdef _LZMA_LOC_OPT
+ RC_INIT_VAR
+ #endif
+ for(i = 0; i < numLevels; i++)
+ {
+ #ifdef _LZMA_LOC_OPT
+ CProb *prob = probs + mi;
+ RC_GET_BIT2(prob, mi, ; , symbol |= (1 << i))
+ #else
+ int bit = RangeDecoderBitDecode(probs + mi, rd);
+ mi = mi + mi + bit;
+ symbol |= (bit << i);
+ #endif
+ }
+ #ifdef _LZMA_LOC_OPT
+ RC_FLUSH_VAR
+ #endif
+ return symbol;
+}
+
+Byte LzmaLiteralDecode(CProb *probs, CRangeDecoder *rd)
+{
+ int symbol = 1;
+ #ifdef _LZMA_LOC_OPT
+ RC_INIT_VAR
+ #endif
+ do
+ {
+ #ifdef _LZMA_LOC_OPT
+ CProb *prob = probs + symbol;
+ RC_GET_BIT(prob, symbol)
+ #else
+ symbol = (symbol + symbol) | RangeDecoderBitDecode(probs + symbol, rd);
+ #endif
+ }
+ while (symbol < 0x100);
+ #ifdef _LZMA_LOC_OPT
+ RC_FLUSH_VAR
+ #endif
+ return symbol;
+}
+
+Byte LzmaLiteralDecodeMatch(CProb *probs, CRangeDecoder *rd, Byte matchByte)
+{
+ int symbol = 1;
+ #ifdef _LZMA_LOC_OPT
+ RC_INIT_VAR
+ #endif
+ do
+ {
+ int bit;
+ int matchBit = (matchByte >> 7) & 1;
+ matchByte <<= 1;
+ #ifdef _LZMA_LOC_OPT
+ {
+ CProb *prob = probs + ((1 + matchBit) << 8) + symbol;
+ RC_GET_BIT2(prob, symbol, bit = 0, bit = 1)
+ }
+ #else
+ bit = RangeDecoderBitDecode(probs + ((1 + matchBit) << 8) + symbol, rd);
+ symbol = (symbol << 1) | bit;
+ #endif
+ if (matchBit != bit)
+ {
+ while (symbol < 0x100)
+ {
+ #ifdef _LZMA_LOC_OPT
+ CProb *prob = probs + symbol;
+ RC_GET_BIT(prob, symbol)
+ #else
+ symbol = (symbol + symbol) | RangeDecoderBitDecode(probs + symbol, rd);
+ #endif
+ }
+ break;
+ }
+ }
+ while (symbol < 0x100);
+ #ifdef _LZMA_LOC_OPT
+ RC_FLUSH_VAR
+ #endif
+ return symbol;
+}
+
+#define kNumPosBitsMax 4
+#define kNumPosStatesMax (1 << kNumPosBitsMax)
+
+#define kLenNumLowBits 3
+#define kLenNumLowSymbols (1 << kLenNumLowBits)
+#define kLenNumMidBits 3
+#define kLenNumMidSymbols (1 << kLenNumMidBits)
+#define kLenNumHighBits 8
+#define kLenNumHighSymbols (1 << kLenNumHighBits)
+
+#define LenChoice 0
+#define LenChoice2 (LenChoice + 1)
+#define LenLow (LenChoice2 + 1)
+#define LenMid (LenLow + (kNumPosStatesMax << kLenNumLowBits))
+#define LenHigh (LenMid + (kNumPosStatesMax << kLenNumMidBits))
+#define kNumLenProbs (LenHigh + kLenNumHighSymbols)
+
+int LzmaLenDecode(CProb *p, CRangeDecoder *rd, int posState)
+{
+ if(RangeDecoderBitDecode(p + LenChoice, rd) == 0)
+ return RangeDecoderBitTreeDecode(p + LenLow +
+ (posState << kLenNumLowBits), kLenNumLowBits, rd);
+ if(RangeDecoderBitDecode(p + LenChoice2, rd) == 0)
+ return kLenNumLowSymbols + RangeDecoderBitTreeDecode(p + LenMid +
+ (posState << kLenNumMidBits), kLenNumMidBits, rd);
+ return kLenNumLowSymbols + kLenNumMidSymbols +
+ RangeDecoderBitTreeDecode(p + LenHigh, kLenNumHighBits, rd);
+}
+
+#define kNumStates 12
+
+#define kStartPosModelIndex 4
+#define kEndPosModelIndex 14
+#define kNumFullDistances (1 << (kEndPosModelIndex >> 1))
+
+#define kNumPosSlotBits 6
+#define kNumLenToPosStates 4
+
+#define kNumAlignBits 4
+#define kAlignTableSize (1 << kNumAlignBits)
+
+#define kMatchMinLen 2
+
+#define IsMatch 0
+#define IsRep (IsMatch + (kNumStates << kNumPosBitsMax))
+#define IsRepG0 (IsRep + kNumStates)
+#define IsRepG1 (IsRepG0 + kNumStates)
+#define IsRepG2 (IsRepG1 + kNumStates)
+#define IsRep0Long (IsRepG2 + kNumStates)
+#define PosSlot (IsRep0Long + (kNumStates << kNumPosBitsMax))
+#define SpecPos (PosSlot + (kNumLenToPosStates << kNumPosSlotBits))
+#define Align (SpecPos + kNumFullDistances - kEndPosModelIndex)
+#define LenCoder (Align + kAlignTableSize)
+#define RepLenCoder (LenCoder + kNumLenProbs)
+#define Literal (RepLenCoder + kNumLenProbs)
+
+#if Literal != LZMA_BASE_SIZE
+StopCompilingDueBUG
+#endif
+
+#ifdef _LZMA_OUT_READ
+
+typedef struct _LzmaVarState
+{
+ CRangeDecoder RangeDecoder;
+ Byte *Dictionary;
+ UInt32 DictionarySize;
+ UInt32 DictionaryPos;
+ UInt32 GlobalPos;
+ UInt32 Reps[4];
+ int lc;
+ int lp;
+ int pb;
+ int State;
+ int PreviousIsMatch;
+ int RemainLen;
+} LzmaVarState;
+
+int LzmaDecoderInit(
+ unsigned char *buffer, UInt32 bufferSize,
+ int lc, int lp, int pb,
+ unsigned char *dictionary, UInt32 dictionarySize,
+ #ifdef _LZMA_IN_CB
+ ILzmaInCallback *inCallback
+ #else
+ unsigned char *inStream, UInt32 inSize
+ #endif
+ )
+{
+ LzmaVarState *vs = (LzmaVarState *)buffer;
+ CProb *p = (CProb *)(buffer + sizeof(LzmaVarState));
+ UInt32 numProbs = Literal + ((UInt32)LZMA_LIT_SIZE << (lc + lp));
+ UInt32 i;
+ if (bufferSize < numProbs * sizeof(CProb) + sizeof(LzmaVarState))
+ return LZMA_RESULT_NOT_ENOUGH_MEM;
+ vs->Dictionary = dictionary;
+ vs->DictionarySize = dictionarySize;
+ vs->DictionaryPos = 0;
+ vs->GlobalPos = 0;
+ vs->Reps[0] = vs->Reps[1] = vs->Reps[2] = vs->Reps[3] = 1;
+ vs->lc = lc;
+ vs->lp = lp;
+ vs->pb = pb;
+ vs->State = 0;
+ vs->PreviousIsMatch = 0;
+ vs->RemainLen = 0;
+ dictionary[dictionarySize - 1] = 0;
+ for (i = 0; i < numProbs; i++)
+ p[i] = kBitModelTotal >> 1;
+ RangeDecoderInit(&vs->RangeDecoder,
+ #ifdef _LZMA_IN_CB
+ inCallback
+ #else
+ inStream, inSize
+ #endif
+ );
+ return LZMA_RESULT_OK;
+}
+
+int LzmaDecode(unsigned char *buffer,
+ unsigned char *outStream, UInt32 outSize,
+ UInt32 *outSizeProcessed)
+{
+ LzmaVarState *vs = (LzmaVarState *)buffer;
+ CProb *p = (CProb *)(buffer + sizeof(LzmaVarState));
+ CRangeDecoder rd = vs->RangeDecoder;
+ int state = vs->State;
+ int previousIsMatch = vs->PreviousIsMatch;
+ Byte previousByte;
+ UInt32 rep0 = vs->Reps[0], rep1 = vs->Reps[1], rep2 = vs->Reps[2], rep3 = vs->Reps[3];
+ UInt32 nowPos = 0;
+ UInt32 posStateMask = (1 << (vs->pb)) - 1;
+ UInt32 literalPosMask = (1 << (vs->lp)) - 1;
+ int lc = vs->lc;
+ int len = vs->RemainLen;
+ UInt32 globalPos = vs->GlobalPos;
+
+ Byte *dictionary = vs->Dictionary;
+ UInt32 dictionarySize = vs->DictionarySize;
+ UInt32 dictionaryPos = vs->DictionaryPos;
+
+ if (len == -1)
+ {
+ *outSizeProcessed = 0;
+ return LZMA_RESULT_OK;
+ }
+
+ while(len > 0 && nowPos < outSize)
+ {
+ UInt32 pos = dictionaryPos - rep0;
+ if (pos >= dictionarySize)
+ pos += dictionarySize;
+ outStream[nowPos++] = dictionary[dictionaryPos] = dictionary[pos];
+ if (++dictionaryPos == dictionarySize)
+ dictionaryPos = 0;
+ len--;
+ }
+ if (dictionaryPos == 0)
+ previousByte = dictionary[dictionarySize - 1];
+ else
+ previousByte = dictionary[dictionaryPos - 1];
+#else
+
+int LzmaDecode(
+ Byte *buffer, UInt32 bufferSize,
+ int lc, int lp, int pb,
+ #ifdef _LZMA_IN_CB
+ ILzmaInCallback *inCallback,
+ #else
+ unsigned char *inStream, UInt32 inSize,
+ #endif
+ unsigned char *outStream, UInt32 outSize,
+ UInt32 *outSizeProcessed)
+{
+ UInt32 numProbs = Literal + ((UInt32)LZMA_LIT_SIZE << (lc + lp));
+ CProb *p = (CProb *)buffer;
+ CRangeDecoder rd;
+ UInt32 i;
+ int state = 0;
+ int previousIsMatch = 0;
+ Byte previousByte = 0;
+ UInt32 rep0 = 1, rep1 = 1, rep2 = 1, rep3 = 1;
+ UInt32 nowPos = 0;
+ UInt32 posStateMask = (1 << pb) - 1;
+ UInt32 literalPosMask = (1 << lp) - 1;
+ int len = 0;
+ if (bufferSize < numProbs * sizeof(CProb))
+ return LZMA_RESULT_NOT_ENOUGH_MEM;
+ for (i = 0; i < numProbs; i++)
+ p[i] = kBitModelTotal >> 1;
+ RangeDecoderInit(&rd,
+ #ifdef _LZMA_IN_CB
+ inCallback
+ #else
+ inStream, inSize
+ #endif
+ );
+#endif
+
+ *outSizeProcessed = 0;
+ while(nowPos < outSize)
+ {
+ int posState = (int)(
+ (nowPos
+ #ifdef _LZMA_OUT_READ
+ + globalPos
+ #endif
+ )
+ & posStateMask);
+ #ifdef _LZMA_IN_CB
+ if (rd.Result != LZMA_RESULT_OK)
+ return rd.Result;
+ #endif
+ if (rd.ExtraBytes != 0)
+ return LZMA_RESULT_DATA_ERROR;
+ if (RangeDecoderBitDecode(p + IsMatch + (state << kNumPosBitsMax) + posState, &rd) == 0)
+ {
+ CProb *probs = p + Literal + (LZMA_LIT_SIZE *
+ (((
+ (nowPos
+ #ifdef _LZMA_OUT_READ
+ + globalPos
+ #endif
+ )
+ & literalPosMask) << lc) + (previousByte >> (8 - lc))));
+
+ if (state < 4) state = 0;
+ else if (state < 10) state -= 3;
+ else state -= 6;
+ if (previousIsMatch)
+ {
+ Byte matchByte;
+ #ifdef _LZMA_OUT_READ
+ UInt32 pos = dictionaryPos - rep0;
+ if (pos >= dictionarySize)
+ pos += dictionarySize;
+ matchByte = dictionary[pos];
+ #else
+ matchByte = outStream[nowPos - rep0];
+ #endif
+ previousByte = LzmaLiteralDecodeMatch(probs, &rd, matchByte);
+ previousIsMatch = 0;
+ }
+ else
+ previousByte = LzmaLiteralDecode(probs, &rd);
+ outStream[nowPos++] = previousByte;
+ #ifdef _LZMA_OUT_READ
+ dictionary[dictionaryPos] = previousByte;
+ if (++dictionaryPos == dictionarySize)
+ dictionaryPos = 0;
+ #endif
+ }
+ else
+ {
+ previousIsMatch = 1;
+ if (RangeDecoderBitDecode(p + IsRep + state, &rd) == 1)
+ {
+ if (RangeDecoderBitDecode(p + IsRepG0 + state, &rd) == 0)
+ {
+ if (RangeDecoderBitDecode(p + IsRep0Long + (state << kNumPosBitsMax) + posState, &rd) == 0)
+ {
+ #ifdef _LZMA_OUT_READ
+ UInt32 pos;
+ #endif
+ if (
+ (nowPos
+ #ifdef _LZMA_OUT_READ
+ + globalPos
+ #endif
+ )
+ == 0)
+ return LZMA_RESULT_DATA_ERROR;
+ state = state < 7 ? 9 : 11;
+ #ifdef _LZMA_OUT_READ
+ pos = dictionaryPos - rep0;
+ if (pos >= dictionarySize)
+ pos += dictionarySize;
+ previousByte = dictionary[pos];
+ dictionary[dictionaryPos] = previousByte;
+ if (++dictionaryPos == dictionarySize)
+ dictionaryPos = 0;
+ #else
+ previousByte = outStream[nowPos - rep0];
+ #endif
+ outStream[nowPos++] = previousByte;
+ continue;
+ }
+ }
+ else
+ {
+ UInt32 distance;
+ if(RangeDecoderBitDecode(p + IsRepG1 + state, &rd) == 0)
+ distance = rep1;
+ else
+ {
+ if(RangeDecoderBitDecode(p + IsRepG2 + state, &rd) == 0)
+ distance = rep2;
+ else
+ {
+ distance = rep3;
+ rep3 = rep2;
+ }
+ rep2 = rep1;
+ }
+ rep1 = rep0;
+ rep0 = distance;
+ }
+ len = LzmaLenDecode(p + RepLenCoder, &rd, posState);
+ state = state < 7 ? 8 : 11;
+ }
+ else
+ {
+ int posSlot;
+ rep3 = rep2;
+ rep2 = rep1;
+ rep1 = rep0;
+ state = state < 7 ? 7 : 10;
+ len = LzmaLenDecode(p + LenCoder, &rd, posState);
+ posSlot = RangeDecoderBitTreeDecode(p + PosSlot +
+ ((len < kNumLenToPosStates ? len : kNumLenToPosStates - 1) <<
+ kNumPosSlotBits), kNumPosSlotBits, &rd);
+ if (posSlot >= kStartPosModelIndex)
+ {
+ int numDirectBits = ((posSlot >> 1) - 1);
+ rep0 = ((2 | ((UInt32)posSlot & 1)) << numDirectBits);
+ if (posSlot < kEndPosModelIndex)
+ {
+ rep0 += RangeDecoderReverseBitTreeDecode(
+ p + SpecPos + rep0 - posSlot - 1, numDirectBits, &rd);
+ }
+ else
+ {
+ rep0 += RangeDecoderDecodeDirectBits(&rd,
+ numDirectBits - kNumAlignBits) << kNumAlignBits;
+ rep0 += RangeDecoderReverseBitTreeDecode(p + Align, kNumAlignBits, &rd);
+ }
+ }
+ else
+ rep0 = posSlot;
+ rep0++;
+ }
+ if (rep0 == (UInt32)(0))
+ {
+ /* it's for stream version */
+ len = -1;
+ break;
+ }
+ if (rep0 > nowPos
+ #ifdef _LZMA_OUT_READ
+ + globalPos
+ #endif
+ )
+ {
+ return LZMA_RESULT_DATA_ERROR;
+ }
+ len += kMatchMinLen;
+ do
+ {
+ #ifdef _LZMA_OUT_READ
+ UInt32 pos = dictionaryPos - rep0;
+ if (pos >= dictionarySize)
+ pos += dictionarySize;
+ previousByte = dictionary[pos];
+ dictionary[dictionaryPos] = previousByte;
+ if (++dictionaryPos == dictionarySize)
+ dictionaryPos = 0;
+ #else
+ previousByte = outStream[nowPos - rep0];
+ #endif
+ outStream[nowPos++] = previousByte;
+ len--;
+ }
+ while(len > 0 && nowPos < outSize);
+ }
+ }
+
+ #ifdef _LZMA_OUT_READ
+ vs->RangeDecoder = rd;
+ vs->DictionaryPos = dictionaryPos;
+ vs->GlobalPos = globalPos + nowPos;
+ vs->Reps[0] = rep0;
+ vs->Reps[1] = rep1;
+ vs->Reps[2] = rep2;
+ vs->Reps[3] = rep3;
+ vs->State = state;
+ vs->PreviousIsMatch = previousIsMatch;
+ vs->RemainLen = len;
+ #endif
+
+ *outSizeProcessed = nowPos;
+ return LZMA_RESULT_OK;
+}
--- /dev/null
+/*
+ LzmaDecode.h
+ LZMA Decoder interface
+
+ LZMA SDK 4.05 Copyright (c) 1999-2004 Igor Pavlov (2004-08-25)
+ http://www.7-zip.org/
+
+ LZMA SDK is licensed under two licenses:
+ 1) GNU Lesser General Public License (GNU LGPL)
+ 2) Common Public License (CPL)
+ It means that you can select one of these two licenses and
+ follow rules of that license.
+
+ SPECIAL EXCEPTION:
+ Igor Pavlov, as the author of this code, expressly permits you to
+ statically or dynamically link your code (or bind by name) to the
+ interfaces of this file without subjecting your linked code to the
+ terms of the CPL or GNU LGPL. Any modifications or additions
+ to this file, however, are subject to the LGPL or CPL terms.
+*/
+
+#ifndef __LZMADECODE_H
+#define __LZMADECODE_H
+
+/* #define _LZMA_IN_CB */
+/* Use callback for input data */
+
+/* #define _LZMA_OUT_READ */
+/* Use read function for output data */
+
+/* #define _LZMA_PROB32 */
+/* It can increase speed on some 32-bit CPUs,
+ but memory usage will be doubled in that case */
+
+/* #define _LZMA_LOC_OPT */
+/* Enable local speed optimizations inside code */
+
+#ifndef UInt32
+#ifdef _LZMA_UINT32_IS_ULONG
+#define UInt32 unsigned long
+#else
+#define UInt32 unsigned int
+#endif
+#endif
+
+#ifdef _LZMA_PROB32
+#define CProb UInt32
+#else
+#define CProb unsigned short
+#endif
+
+#define LZMA_RESULT_OK 0
+#define LZMA_RESULT_DATA_ERROR 1
+#define LZMA_RESULT_NOT_ENOUGH_MEM 2
+
+#ifdef _LZMA_IN_CB
+typedef struct _ILzmaInCallback
+{
+ int (*Read)(void *object, unsigned char **buffer, UInt32 *bufferSize);
+} ILzmaInCallback;
+#endif
+
+#define LZMA_BASE_SIZE 1846
+#define LZMA_LIT_SIZE 768
+
+/*
+bufferSize = (LZMA_BASE_SIZE + (LZMA_LIT_SIZE << (lc + lp)))* sizeof(CProb)
+bufferSize += 100 in case of _LZMA_OUT_READ
+by default CProb is unsigned short,
+but if specify _LZMA_PROB_32, CProb will be UInt32(unsigned int)
+*/
+
+#ifdef _LZMA_OUT_READ
+int LzmaDecoderInit(
+ unsigned char *buffer, UInt32 bufferSize,
+ int lc, int lp, int pb,
+ unsigned char *dictionary, UInt32 dictionarySize,
+ #ifdef _LZMA_IN_CB
+ ILzmaInCallback *inCallback
+ #else
+ unsigned char *inStream, UInt32 inSize
+ #endif
+);
+#endif
+
+int LzmaDecode(
+ unsigned char *buffer,
+ #ifndef _LZMA_OUT_READ
+ UInt32 bufferSize,
+ int lc, int lp, int pb,
+ #ifdef _LZMA_IN_CB
+ ILzmaInCallback *inCallback,
+ #else
+ unsigned char *inStream, UInt32 inSize,
+ #endif
+ #endif
+ unsigned char *outStream, UInt32 outSize,
+ UInt32 *outSizeProcessed);
+
+#endif
--- /dev/null
+#
+# Makefile for Broadcom BCM947XX boards
+#
+# Copyright 2001-2003, Broadcom Corporation
+# All Rights Reserved.
+#
+# THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
+# KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
+# SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
+# FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
+#
+# Copyright 2004 Manuel Novoa III <mjn3@codepoet.org>
+# Modified to support bzip'd kernels.
+# Of course, it would be better to integrate bunzip capability into CFE.
+#
+# Copyright 2005 Oleg I. Vdovikin <oleg@cs.msu.su>
+# Cleaned up, modified for lzma support, removed from kernel
+#
+
+TEXT_START := 0x80001000
+BZ_TEXT_START := 0x80300000
+
+OBJCOPY := $(CROSS_COMPILE)objcopy -O binary -R .reginfo -R .note -R .comment -R .mdebug -S
+
+CFLAGS = -D__KERNEL__ -Wall -Wstrict-prototypes -Wno-trigraphs -Os \
+ -fno-strict-aliasing -fno-common -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic \
+ -ffunction-sections -pipe -mlong-calls -fno-common \
+ -mabi=32 -march=mips32 -Wa,-32 -Wa,-march=mips32 -Wa,-mips32 -Wa,--trap
+CFLAGS += -DLOADADDR=$(TEXT_START) -D_LZMA_IN_CB
+
+ASFLAGS = $(CFLAGS) -D__ASSEMBLY__ -DBZ_TEXT_START=$(BZ_TEXT_START)
+
+SEDFLAGS := s/BZ_TEXT_START/$(BZ_TEXT_START)/;s/TEXT_START/$(TEXT_START)/
+
+OBJECTS := head.o data.o
+
+all: loader.gz loader.elf
+
+# Don't build dependencies, this may die if $(CC) isn't gcc
+dep:
+
+install:
+
+loader.gz: loader
+ gzip -nc9 $< > $@
+
+loader.elf: loader.o
+ cp $< $@
+
+loader: loader.o
+ $(OBJCOPY) $< $@
+
+loader.o: loader.lds $(OBJECTS)
+ $(LD) -static --gc-sections -no-warn-mismatch -T loader.lds -o $@ $(OBJECTS)
+
+loader.lds: loader.lds.in Makefile
+ @sed "$(SEDFLAGS)" < $< > $@
+
+data.o: data.lds decompress.image
+ $(LD) -no-warn-mismatch -T data.lds -r -o $@ -b binary decompress.image -b elf32-tradlittlemips
+
+data.lds:
+ @echo "SECTIONS { .data : { code_start = .; *(.data) code_stop = .; }}" > $@
+
+decompress.image: decompress
+ $(OBJCOPY) $< $@
+
+decompress: decompress.lds decompress.o LzmaDecode.o
+ $(LD) -static --gc-sections -no-warn-mismatch -T decompress.lds -o $@ decompress.o LzmaDecode.o
+
+decompress.lds: decompress.lds.in Makefile
+ @sed "$(SEDFLAGS)" < $< > $@
+
+mrproper: clean
+
+clean:
+ rm -f loader.gz loader decompress *.lds *.o *.image
--- /dev/null
+/*
+ * LZMA compressed kernel decompressor for bcm947xx boards
+ *
+ * Copyright (C) 2005 by Oleg I. Vdovikin <oleg@cs.msu.su>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+The code is intended to decompress kernel, being compressed using lzma utility
+build using 7zip LZMA SDK. This utility is located in the LZMA_Alone directory
+
+decompressor code expects that your .trx file consist of three partitions:
+
+1) decompressor itself (this is gziped code which pmon/cfe will extract and run
+on boot-up instead of real kernel)
+2) LZMA compressed kernel (both streamed and regular modes are supported now)
+3) Root filesystem
+
+Please be sure to apply the following patch for use this new trx layout (it will
+allow using both new and old trx files for root filesystem lookup code)
+
+--- linuz/arch/mips/brcm-boards/bcm947xx/setup.c 2005-01-23 19:24:27.503322896 +0300
++++ linux/arch/mips/brcm-boards/bcm947xx/setup.c 2005-01-23 19:29:05.237100944 +0300
+@@ -221,7 +221,9 @@
+ /* Try looking at TRX header for rootfs offset */
+ if (le32_to_cpu(trx->magic) == TRX_MAGIC) {
+ bcm947xx_parts[1].offset = off;
+- if (le32_to_cpu(trx->offsets[1]) > off)
++ if (le32_to_cpu(trx->offsets[2]) > off)
++ off = le32_to_cpu(trx->offsets[2]);
++ else if (le32_to_cpu(trx->offsets[1]) > off)
+ off = le32_to_cpu(trx->offsets[1]);
+ continue;
+ }
+
+
+Revision history:
+ 0.02 Initial release
+ 0.03 Added Mineharu Takahara <mtakahar@yahoo.com> patch to pass actual
+ output size to decoder (stream mode compressed input is not
+ a requirement anymore)
+ 0.04 Reordered functions using lds script
--- /dev/null
+/*
+ * LZMA compressed kernel decompressor for bcm947xx boards
+ *
+ * Copyright (C) 2005 by Oleg I. Vdovikin <oleg@cs.msu.su>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ *
+ * Please note, this was code based on the bunzip2 decompressor code
+ * by Manuel Novoa III (mjn3@codepoet.org), although the only thing left
+ * is an idea and part of original vendor code
+ *
+ *
+ * 12-Mar-2005 Mineharu Takahara <mtakahar@yahoo.com>
+ * pass actual output size to decoder (stream mode
+ * compressed input is not a requirement anymore)
+ *
+ * 24-Apr-2005 Oleg I. Vdovikin
+ * reordered functions using lds script, removed forward decl
+ *
+ */
+
+#include "LzmaDecode.h"
+
+#define BCM4710_FLASH 0x1fc00000 /* Flash */
+
+#define KSEG0 0x80000000
+#define KSEG1 0xa0000000
+
+#define KSEG1ADDR(a) ((((unsigned)(a)) & 0x1fffffffU) | KSEG1)
+
+#define Index_Invalidate_I 0x00
+#define Index_Writeback_Inv_D 0x01
+
+#define cache_unroll(base,op) \
+ __asm__ __volatile__( \
+ ".set noreorder;\n" \
+ ".set mips3;\n" \
+ "cache %1, (%0);\n" \
+ ".set mips0;\n" \
+ ".set reorder\n" \
+ : \
+ : "r" (base), \
+ "i" (op));
+
+static __inline__ void blast_icache(unsigned long size, unsigned long lsize)
+{
+ unsigned long start = KSEG0;
+ unsigned long end = (start + size);
+
+ while(start < end) {
+ cache_unroll(start,Index_Invalidate_I);
+ start += lsize;
+ }
+}
+
+static __inline__ void blast_dcache(unsigned long size, unsigned long lsize)
+{
+ unsigned long start = KSEG0;
+ unsigned long end = (start + size);
+
+ while(start < end) {
+ cache_unroll(start,Index_Writeback_Inv_D);
+ start += lsize;
+ }
+}
+
+#define TRX_MAGIC 0x30524448 /* "HDR0" */
+
+struct trx_header {
+ unsigned int magic; /* "HDR0" */
+ unsigned int len; /* Length of file including header */
+ unsigned int crc32; /* 32-bit CRC from flag_version to end of file */
+ unsigned int flag_version; /* 0:15 flags, 16:31 version */
+ unsigned int offsets[3]; /* Offsets of partitions from start of header */
+};
+
+/* beyound the image end, size not known in advance */
+extern unsigned char workspace[];
+
+unsigned int offset;
+unsigned char *data;
+
+/* flash access should be aligned, so wrapper is used */
+/* read byte from the flash, all accesses are 32-bit aligned */
+static int read_byte(void *object, unsigned char **buffer, UInt32 *bufferSize)
+{
+ static unsigned int val;
+
+ if (((unsigned int)offset % 4) == 0) {
+ val = *(unsigned int *)data;
+ data += 4;
+ }
+
+ *bufferSize = 1;
+ *buffer = ((unsigned char *)&val) + (offset++ & 3);
+
+ return LZMA_RESULT_OK;
+}
+
+static __inline__ unsigned char get_byte(void)
+{
+ unsigned char *buffer;
+ UInt32 fake;
+
+ return read_byte(0, &buffer, &fake), *buffer;
+}
+
+/* should be the first function */
+void entry(unsigned long icache_size, unsigned long icache_lsize,
+ unsigned long dcache_size, unsigned long dcache_lsize)
+{
+ unsigned int i; /* temp value */
+ unsigned int lc; /* literal context bits */
+ unsigned int lp; /* literal pos state bits */
+ unsigned int pb; /* pos state bits */
+ unsigned int osize; /* uncompressed size */
+
+ ILzmaInCallback callback;
+ callback.Read = read_byte;
+
+ /* look for trx header, 32-bit data access */
+ for (data = ((unsigned char *) KSEG1ADDR(BCM4710_FLASH));
+ ((struct trx_header *)data)->magic != TRX_MAGIC; data += 65536);
+
+ /* compressed kernel is in the partition 0 or 1 */
+ if (((struct trx_header *)data)->offsets[1] > 65536)
+ data += ((struct trx_header *)data)->offsets[0];
+ else
+ data += ((struct trx_header *)data)->offsets[1];
+
+ offset = 0;
+
+ /* lzma args */
+ i = get_byte();
+ lc = i % 9, i = i / 9;
+ lp = i % 5, pb = i / 5;
+
+ /* skip rest of the LZMA coder property */
+ for (i = 0; i < 4; i++)
+ get_byte();
+
+ /* read the lower half of uncompressed size in the header */
+ osize = ((unsigned int)get_byte()) +
+ ((unsigned int)get_byte() << 8) +
+ ((unsigned int)get_byte() << 16) +
+ ((unsigned int)get_byte() << 24);
+
+ /* skip rest of the header (upper half of uncompressed size) */
+ for (i = 0; i < 4; i++)
+ get_byte();
+
+ /* decompress kernel */
+ if (LzmaDecode(workspace, ~0, lc, lp, pb, &callback,
+ (unsigned char*)LOADADDR, osize, &i) == LZMA_RESULT_OK)
+ {
+ blast_dcache(dcache_size, dcache_lsize);
+ blast_icache(icache_size, icache_lsize);
+
+ /* Jump to load address */
+ ((void (*)(void)) LOADADDR)();
+ }
+}
--- /dev/null
+OUTPUT_ARCH(mips)
+ENTRY(entry)
+SECTIONS {
+ . = BZ_TEXT_START;
+ .text : {
+ *(.text.entry)
+ *(.text)
+ *(.rodata)
+ }
+
+ .data : {
+ *(.data)
+ }
+
+ .bss : {
+ *(.bss)
+ }
+
+ workspace = .;
+}
--- /dev/null
+/* Copyright 2005 Oleg I. Vdovikin (oleg@cs.msu.su) */
+/* cache manipulation adapted from Broadcom code */
+/* idea taken from original bunzip2 decompressor code */
+/* Copyright 2004 Manuel Novoa III (mjn3@codepoet.org) */
+/* Licensed under the linux kernel's version of the GPL.*/
+
+#include <asm/asm.h>
+#include <asm/regdef.h>
+
+#define KSEG0 0x80000000
+
+#define C0_CONFIG $16
+#define C0_TAGLO $28
+#define C0_TAGHI $29
+
+#define CONF1_DA_SHIFT 7 /* D$ associativity */
+#define CONF1_DA_MASK 0x00000380
+#define CONF1_DA_BASE 1
+#define CONF1_DL_SHIFT 10 /* D$ line size */
+#define CONF1_DL_MASK 0x00001c00
+#define CONF1_DL_BASE 2
+#define CONF1_DS_SHIFT 13 /* D$ sets/way */
+#define CONF1_DS_MASK 0x0000e000
+#define CONF1_DS_BASE 64
+#define CONF1_IA_SHIFT 16 /* I$ associativity */
+#define CONF1_IA_MASK 0x00070000
+#define CONF1_IA_BASE 1
+#define CONF1_IL_SHIFT 19 /* I$ line size */
+#define CONF1_IL_MASK 0x00380000
+#define CONF1_IL_BASE 2
+#define CONF1_IS_SHIFT 22 /* Instruction cache sets/way */
+#define CONF1_IS_MASK 0x01c00000
+#define CONF1_IS_BASE 64
+
+#define Index_Invalidate_I 0x00
+#define Index_Writeback_Inv_D 0x01
+
+ .text
+ LEAF(startup)
+ .set noreorder
+
+ /* Copy decompressor code to the right place */
+ li t2, BZ_TEXT_START
+ add a0, t2, 0
+ la a1, code_start
+ la a2, code_stop
+$L1:
+ lw t0, 0(a1)
+ sw t0, 0(a0)
+ add a1, 4
+ add a0, 4
+ blt a1, a2, $L1
+ nop
+
+ /* At this point we need to invalidate dcache and */
+ /* icache before jumping to new code */
+
+1: /* Get cache sizes */
+ .set mips32
+ mfc0 s0,C0_CONFIG,1
+ .set mips0
+
+ li s1,CONF1_DL_MASK
+ and s1,s0
+ beq s1,zero,nodc
+ nop
+
+ srl s1,CONF1_DL_SHIFT
+ li t0,CONF1_DL_BASE
+ sll s1,t0,s1 /* s1 has D$ cache line size */
+
+ li s2,CONF1_DA_MASK
+ and s2,s0
+ srl s2,CONF1_DA_SHIFT
+ addiu s2,CONF1_DA_BASE /* s2 now has D$ associativity */
+
+ li t0,CONF1_DS_MASK
+ and t0,s0
+ srl t0,CONF1_DS_SHIFT
+ li s3,CONF1_DS_BASE
+ sll s3,s3,t0 /* s3 has D$ sets per way */
+
+ multu s2,s3 /* sets/way * associativity */
+ mflo t0 /* total cache lines */
+
+ multu s1,t0 /* D$ linesize * lines */
+ mflo s2 /* s2 is now D$ size in bytes */
+
+ /* Initilize the D$: */
+ mtc0 zero,C0_TAGLO
+ mtc0 zero,C0_TAGHI
+
+ li t0,KSEG0 /* Just an address for the first $ line */
+ addu t1,t0,s2 /* + size of cache == end */
+
+ .set mips3
+1: cache Index_Writeback_Inv_D,0(t0)
+ .set mips0
+ bne t0,t1,1b
+ addu t0,s1
+
+nodc:
+ /* Now we get to do it all again for the I$ */
+
+ move s3,zero /* just in case there is no icache */
+ move s4,zero
+
+ li t0,CONF1_IL_MASK
+ and t0,s0
+ beq t0,zero,noic
+ nop
+
+ srl t0,CONF1_IL_SHIFT
+ li s3,CONF1_IL_BASE
+ sll s3,t0 /* s3 has I$ cache line size */
+
+ li t0,CONF1_IA_MASK
+ and t0,s0
+ srl t0,CONF1_IA_SHIFT
+ addiu s4,t0,CONF1_IA_BASE /* s4 now has I$ associativity */
+
+ li t0,CONF1_IS_MASK
+ and t0,s0
+ srl t0,CONF1_IS_SHIFT
+ li s5,CONF1_IS_BASE
+ sll s5,t0 /* s5 has I$ sets per way */
+
+ multu s4,s5 /* sets/way * associativity */
+ mflo t0 /* s4 is now total cache lines */
+
+ multu s3,t0 /* I$ linesize * lines */
+ mflo s4 /* s4 is cache size in bytes */
+
+ /* Initilize the I$: */
+ mtc0 zero,C0_TAGLO
+ mtc0 zero,C0_TAGHI
+
+ li t0,KSEG0 /* Just an address for the first $ line */
+ addu t1,t0,s4 /* + size of cache == end */
+
+ .set mips3
+1: cache Index_Invalidate_I,0(t0)
+ .set mips0
+ bne t0,t1,1b
+ addu t0,s3
+
+noic:
+ move a0,s3 /* icache line size */
+ move a1,s4 /* icache size */
+ move a2,s1 /* dcache line size */
+ jal t2
+ move a3,s2 /* dcache size */
+
+ .set reorder
+ END(startup)
--- /dev/null
+OUTPUT_ARCH(mips)
+ENTRY(startup)
+SECTIONS {
+ . = TEXT_START;
+ .text : {
+ *(.text)
+ *(.rodata)
+ }
+
+ .data : {
+ *(.data)
+ }
+
+ .bss : {
+ *(.bss)
+ }
+}
--- /dev/null
+diff -urN linux-2.6.19/arch/mips/Kconfig linux-2.6.19.new/arch/mips/Kconfig
+--- linux-2.6.19/arch/mips/Kconfig 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/arch/mips/Kconfig 2006-12-16 18:46:31.000000000 +0100
+@@ -4,6 +4,10 @@
+ # Horrible source of confusion. Die, die, die ...
+ select EMBEDDED
+
++config CFE
++ bool
++ # Common Firmware Environment
++
+ mainmenu "Linux/MIPS Kernel Configuration"
+
+ menu "Machine selection"
+@@ -12,6 +12,18 @@
+ prompt "System type"
+ default SGI_IP22
+
++config BCM963XX
++ bool "Support for Broadcom BCM963xx SoC"
++ select SYS_SUPPORTS_32BIT_KERNEL
++ select SYS_SUPPORTS_BIG_ENDIAN
++ select SYS_HAS_CPU_MIPS32_R1
++ select HW_HAS_PCI
++ select DMA_NONCOHERENT
++ select IRQ_CPU
++ select CFE
++ help
++ This is a fmaily of boards based on the Broadcom MIPS32
++
+ config MIPS_MTX1
+ bool "4G Systems MTX-1 board"
+ select DMA_NONCOHERENT
+diff -urN linux-2.6.19/arch/mips/Makefile linux-2.6.19.new/arch/mips/Makefile
+--- linux-2.6.19/arch/mips/Makefile 2006-12-16 17:36:29.000000000 +0100
++++ linux-2.6.19.new/arch/mips/Makefile 2006-12-16 18:46:31.000000000 +0100
+@@ -158,6 +158,19 @@
+ #
+
+ #
++# Broadcom BCM963xx SoC
++#
++core-$(CONFIG_BCM963XX) += arch/mips/bcm963xx/
++cflags-$(CONFIG_BCM963XX) += -Iinclude/asm-mips/mach-bcm963xx
++load-$(CONFIG_BCM963XX) += 0xffffffff80010000
++
++
++#
++# Common Firmware Environment
++#
++core-$(CONFIG_CFE) += arch/mips/cfe/
++
++#
+ # Acer PICA 61, Mips Magnum 4000 and Olivetti M700.
+ #
+ core-$(CONFIG_MACH_JAZZ) += arch/mips/jazz/
+diff -urN linux-2.6.19/arch/mips/kernel/cpu-probe.c linux-2.6.19.new/arch/mips/kernel/cpu-probe.c
+--- linux-2.6.19/arch/mips/kernel/cpu-probe.c 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/arch/mips/kernel/cpu-probe.c 2006-12-16 18:46:31.000000000 +0100
+@@ -602,6 +602,25 @@
+ return;
+ }
+
++static inline void cpu_probe_broadcom(struct cpuinfo_mips *c)
++{
++ decode_configs(c);
++ switch (c->processor_id & 0xff00) {
++ case PRID_IMP_BCM6338:
++ c->cputype = CPU_BCM6338;
++ break;
++ case PRID_IMP_BCM6345:
++ c->cputype = CPU_BCM6345;
++ break;
++ case PRID_IMP_BCM6348:
++ c->cputype = CPU_BCM6348;
++ break;
++ default:
++ c->cputype = CPU_UNKNOWN;
++ break;
++ }
++}
++
+ static inline void cpu_probe_mips(struct cpuinfo_mips *c)
+ {
+ decode_configs(c);
+@@ -736,6 +755,9 @@
+ case PRID_COMP_LEGACY:
+ cpu_probe_legacy(c);
+ break;
++ case PRID_COMP_BROADCOM:
++ cpu_probe_broadcom(c);
++ break;
+ case PRID_COMP_MIPS:
+ cpu_probe_mips(c);
+ break;
+diff -urN linux-2.6.19/arch/mips/kernel/proc.c linux-2.6.19.new/arch/mips/kernel/proc.c
+--- linux-2.6.19/arch/mips/kernel/proc.c 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/arch/mips/kernel/proc.c 2006-12-16 18:46:31.000000000 +0100
+@@ -84,6 +84,9 @@
+ [CPU_VR4181A] = "NEC VR4181A",
+ [CPU_SR71000] = "Sandcraft SR71000",
+ [CPU_PR4450] = "Philips PR4450",
++ [CPU_BCM6338] = "BCM6338",
++ [CPU_BCM6345] = "BCM6345",
++ [CPU_BCM6348] = "BCM6348",
+ };
+
+
+diff -urN linux-2.6.19/arch/mips/mm/c-r4k.c linux-2.6.19.new/arch/mips/mm/c-r4k.c
+--- linux-2.6.19/arch/mips/mm/c-r4k.c 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/arch/mips/mm/c-r4k.c 2006-12-16 18:46:31.000000000 +0100
+@@ -852,6 +852,13 @@
+ if (!(config & MIPS_CONF_M))
+ panic("Don't know how to probe P-caches on this cpu.");
+
++ if (c->cputype == CPU_BCM6338 || c->cputype == CPU_BCM6345 || c->cputype == CPU_BCM6348)
++ {
++ printk("bcm963xx: enabling icache and dcache...\n");
++ /* Enable caches */
++ write_c0_diag(read_c0_diag() | 0xC0000000);
++ }
++
+ /*
+ * So we seem to be a MIPS32 or MIPS64 CPU
+ * So let's probe the I-cache ...
+diff -urN linux-2.6.19/arch/mips/mm/tlbex.c linux-2.6.19.new/arch/mips/mm/tlbex.c
+--- linux-2.6.19/arch/mips/mm/tlbex.c 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/arch/mips/mm/tlbex.c 2006-12-16 18:46:31.000000000 +0100
+@@ -880,6 +880,9 @@
+ case CPU_4KSC:
+ case CPU_20KC:
+ case CPU_25KF:
++ case CPU_BCM6338:
++ case CPU_BCM6345:
++ case CPU_BCM6348:
+ tlbw(p);
+ break;
+
+diff -urN linux-2.6.19/arch/mips/pci/Makefile linux-2.6.19.new/arch/mips/pci/Makefile
+--- linux-2.6.19/arch/mips/pci/Makefile 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/arch/mips/pci/Makefile 2006-12-16 18:48:18.000000000 +0100
+@@ -17,6 +17,7 @@
+ obj-$(CONFIG_PCI_VR41XX) += ops-vr41xx.o pci-vr41xx.o
+ obj-$(CONFIG_NEC_CMBVR4133) += fixup-vr4133.o
+ obj-$(CONFIG_MARKEINS) += ops-emma2rh.o pci-emma2rh.o fixup-emma2rh.o
++obj-$(CONFIG_BCM963XX) += fixup-bcm96348.o pci-bcm96348.o ops-bcm96348.o
+
+ #
+ # These are still pretty much in the old state, watch, go blind.
+diff -urN linux-2.6.19/drivers/serial/Makefile linux-2.6.19.new/drivers/serial/Makefile
+--- linux-2.6.19/drivers/serial/Makefile 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/drivers/serial/Makefile 2006-12-16 18:49:17.000000000 +0100
+@@ -56,3 +56,4 @@
+ obj-$(CONFIG_SERIAL_SGI_IOC3) += ioc3_serial.o
+ obj-$(CONFIG_SERIAL_ATMEL) += atmel_serial.o
+ obj-$(CONFIG_SERIAL_NETX) += netx-serial.o
++obj-$(CONFIG_BCM963XX) += bcm63xx_cons.o
+diff -urN linux-2.6.19/include/asm-mips/bootinfo.h linux-2.6.19.new/include/asm-mips/bootinfo.h
+--- linux-2.6.19/include/asm-mips/bootinfo.h 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/include/asm-mips/bootinfo.h 2006-12-16 18:46:31.000000000 +0100
+@@ -212,6 +212,14 @@
+ #define MACH_GROUP_NEC_EMMA2RH 25 /* NEC EMMA2RH (was 23) */
+ #define MACH_NEC_MARKEINS 0 /* NEC EMMA2RH Mark-eins */
+
++/*
++ * Valid machtype for group BRCM
++ */
++#define MACH_GROUP_BRCM 23 /* Broadcom boards */
++#define MACH_BCM96338 0
++#define MACH_BCM96345 1
++#define MACH_BCM96348 2
++
+ #define CL_SIZE COMMAND_LINE_SIZE
+
+ const char *get_system_type(void);
+diff -urN linux-2.6.19/include/asm-mips/cpu.h linux-2.6.19.new/include/asm-mips/cpu.h
+--- linux-2.6.19/include/asm-mips/cpu.h 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/include/asm-mips/cpu.h 2006-12-16 18:46:31.000000000 +0100
+@@ -103,6 +103,13 @@
+
+ #define PRID_IMP_SR71000 0x0400
+
++/* These are the PRID's for when 23:16 == PRID_COMP_BROADCOM
++ */
++
++#define PRID_IMP_BCM6338 0x9000
++#define PRID_IMP_BCM6345 0x8000
++#define PRID_IMP_BCM6348 0x9100
++
+ /*
+ * Definitions for 7:0 on legacy processors
+ */
+@@ -200,7 +207,10 @@
+ #define CPU_SB1A 62
+ #define CPU_74K 63
+ #define CPU_R14000 64
+-#define CPU_LAST 64
++#define CPU_BCM6338 65
++#define CPU_BCM6345 66
++#define CPU_BCM6348 67
++#define CPU_LAST 67
+
+ /*
+ * ISA Level encodings
+diff -urN linux-2.6.19/include/asm-mips/module.h linux-2.6.19.new/include/asm-mips/module.h
+--- linux-2.6.19/include/asm-mips/module.h 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/include/asm-mips/module.h 2006-12-16 19:03:22.000000000 +0100
+@@ -112,6 +112,12 @@
+ #define MODULE_PROC_FAMILY "RM9000 "
+ #elif defined CONFIG_CPU_SB1
+ #define MODULE_PROC_FAMILY "SB1 "
++#elif defined CONFIG_CPU_BCM6338
++#define MODULE_PROC_FAMILY "BCM6338 "
++#elif defined CONFIG_CPU_BCM6345
++#define MODULE_PROC_FAMILY "BCM6345 "
++#elif defined CONFIG_CPU_BCM6348
++#define MODULE_PROC_FAMILY "BCM6348 "
+ #else
+ #error MODULE_PROC_FAMILY undefined for your processor configuration
+ #endif
--- /dev/null
+diff -urN linux-2.6.19/drivers/mtd/maps/Kconfig linux-2.6.19.new/drivers/mtd/maps/Kconfig
+--- linux-2.6.19/drivers/mtd/maps/Kconfig 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/drivers/mtd/maps/Kconfig 2006-12-18 17:21:07.000000000 +0100
+@@ -224,6 +224,13 @@
+ Flash memory access on 4G Systems MTX-1 Board. If you have one of
+ these boards and would like to use the flash chips on it, say 'Y'.
+
++config MTD_BCM963XX
++ tristate "BCM963xx Flash device"
++ depends on MIPS && BCM963XX
++ help
++ Flash memory access on BCM963xx boards. Currently only works with
++ RedBoot and CFE.
++
+ config MTD_DILNETPC
+ tristate "CFI Flash device mapped on DIL/Net PC"
+ depends on X86 && MTD_CONCAT && MTD_PARTITIONS && MTD_CFI_INTELEXT
+diff -urN linux-2.6.19/drivers/mtd/maps/Makefile linux-2.6.19.new/drivers/mtd/maps/Makefile
+--- linux-2.6.19/drivers/mtd/maps/Makefile 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/drivers/mtd/maps/Makefile 2006-12-18 17:21:07.000000000 +0100
+@@ -70,3 +70,4 @@
+ obj-$(CONFIG_MTD_OMAP_NOR) += omap_nor.o
+ obj-$(CONFIG_MTD_MTX1) += mtx-1_flash.o
+ obj-$(CONFIG_MTD_TQM834x) += tqm834x.o
++obj-$(CONFIG_MTD_BCM963XX) += bcm963xx-flash.o
+diff -urN linux-2.6.19/drivers/mtd/redboot.c linux-2.6.19.new/drivers/mtd/redboot.c
+--- linux-2.6.19/drivers/mtd/redboot.c 2006-12-18 17:09:14.000000000 +0100
++++ linux-2.6.19.new/drivers/mtd/redboot.c 2006-12-18 17:14:26.000000000 +0100
+@@ -39,7 +39,7 @@
+ return 1;
+ }
+
+-static int parse_redboot_partitions(struct mtd_info *master,
++int parse_redboot_partitions(struct mtd_info *master,
+ struct mtd_partition **pparts,
+ unsigned long fis_origin)
+ {
+@@ -132,6 +132,14 @@
+ goto out;
+ }
+
++ if (!fis_origin) {
++ for (i = 0; i < numslots; i++) {
++ if (!strncmp(buf[i].name, "RedBoot", 8)) {
++ fis_origin = (buf[i].flash_base & (master->size << 1) - 1);
++ }
++ }
++ }
++
+ for (i = 0; i < numslots; i++) {
+ struct fis_list *new_fl, **prev;
+
+@@ -154,9 +162,8 @@
+ new_fl->img = &buf[i];
+ if (fis_origin) {
+ buf[i].flash_base -= fis_origin;
+- } else {
+- buf[i].flash_base &= master->size-1;
+ }
++ buf[i].flash_base &= (master->size << 1) - 1;
+
+ /* I'm sure the JFFS2 code has done me permanent damage.
+ * I now think the following is _normal_
--- /dev/null
+diff -urN linux-2.6.19.1/include/linux/atm.h linux-2.6.19.1.new/include/linux/atm.h
+--- linux-2.6.19.1/include/linux/atm.h 2006-12-11 20:32:53.000000000 +0100
++++ linux-2.6.19.1.new/include/linux/atm.h 2007-01-07 18:38:50.000000000 +0100
+@@ -48,6 +48,9 @@
+ #define ATM_AAL2 2 /* AAL2 (VBR) */
+ #define ATM_AAL34 3 /* AAL3/4 (data) */
+ #define ATM_AAL5 5 /* AAL5 (data) */
++#if defined(CONFIG_MIPS_BCM963XX)
++#define ATM_BCM_AAL0 14 /* "raw" ATM cells */
++#endif
+
+ /*
+ * socket option name coding functions
+diff -urN linux-2.6.19.1/include/linux/atmbr2684.h linux-2.6.19.1.new/include/linux/atmbr2684.h
+--- linux-2.6.19.1/include/linux/atmbr2684.h 2006-12-11 20:32:53.000000000 +0100
++++ linux-2.6.19.1.new/include/linux/atmbr2684.h 2007-01-07 18:24:01.000000000 +0100
+@@ -78,6 +78,10 @@
+ __u8 vpn_id[7];
+ int send_padding; /* unsupported */
+ int min_size; /* we will pad smaller packets than this */
++#if defined(CONFIG_MIPS_BCM963XX)
++#define FILTER_PPPOE 1
++ int proto_filter; /* protocol filter flag, current only PPPoE */
++#endif
+ };
+
+ /*
+diff -urN linux-2.6.19.1/include/linux/atmdev.h linux-2.6.19.1.new/include/linux/atmdev.h
+--- linux-2.6.19.1/include/linux/atmdev.h 2006-12-11 20:32:53.000000000 +0100
++++ linux-2.6.19.1.new/include/linux/atmdev.h 2007-01-07 18:37:34.000000000 +0100
+@@ -29,6 +29,10 @@
+ #define ATM_DS3_PCR (8000*12)
+ /* DS3: 12 cells in a 125 usec time slot */
+
++#if defined(CONFIG_MIPS_BCM963XX)
++#define atm_sk(__sk) ((struct atm_vcc *)(__sk)->sk_protinfo)
++#define ATM_SD(s) (atm_sk((s)->sk))
++#endif
+
+ #define __AAL_STAT_ITEMS \
+ __HANDLE_ITEM(tx); /* TX okay */ \
+@@ -111,6 +115,9 @@
+ #define ATM_BACKEND_RAW 0
+ #define ATM_BACKEND_PPP 1 /* PPPoATM - RFC2364 */
+ #define ATM_BACKEND_BR2684 2 /* Bridged RFC1483/2684 */
++#if defined(CONFIG_MIPS_BCM963XX)
++#define ATM_BACKEND_RT2684 3 /* Routed RFC1483/2684 */
++#endif
+
+ /* for ATM_GETTYPE */
+ #define ATM_ITFTYP_LEN 8 /* maximum length of interface type name */
+@@ -274,6 +281,9 @@
+
+
+ enum {
++#if defined(CONFIG_MIPS_BCM963XX)
++ ATM_DF_CLOSE, /* close device when last VCC is closed */
++#endif
+ ATM_DF_REMOVED, /* device was removed from atm_devs list */
+ };
+
+@@ -285,8 +295,10 @@
+ #define ATM_ATMOPT_CLP 1 /* set CLP bit */
+
+ struct atm_vcc {
++#if !defined(CONFIG_MIPS_BCM963XX)
+ /* struct sock has to be the first member of atm_vcc */
+ struct sock sk;
++#endif
+ unsigned long flags; /* VCC flags (ATM_VF_*) */
+ short vpi; /* VPI and VCI (types must be equal */
+ /* with sockaddr) */
+@@ -303,6 +315,9 @@
+ void *dev_data; /* per-device data */
+ void *proto_data; /* per-protocol data */
+ struct k_atm_aal_stats *stats; /* pointer to AAL stats group */
++#if defined(CONFIG_MIPS_BCM963XX)
++ struct sock *sk; /* socket backpointer */
++#endif
+ /* SVC part --- may move later ------------------------------------- */
+ short itf; /* interface number */
+ struct sockaddr_atmsvc local;
+@@ -332,7 +347,11 @@
+
+ struct atm_dev_addr {
+ struct sockaddr_atmsvc addr; /* ATM address */
++#if defined(CONFIG_MIPS_BCM963XX)
++ struct atm_dev_addr *next; /* next address */
++#else
+ struct list_head entry; /* next address */
++#endif
+ };
+
+ enum atm_addr_type_t { ATM_ADDR_LOCAL, ATM_ADDR_LECS };
+@@ -346,8 +365,12 @@
+ void *dev_data; /* per-device data */
+ void *phy_data; /* private PHY date */
+ unsigned long flags; /* device flags (ATM_DF_*) */
++#if defined(CONFIG_MIPS_BCM963XX)
++ struct atm_dev_addr *local; /* local ATM addresses */
++#else
+ struct list_head local; /* local ATM addresses */
+ struct list_head lecs; /* LECS ATM addresses learned via ILMI */
++#endif
+ unsigned char esi[ESI_LEN]; /* ESI ("MAC" addr) */
+ struct atm_cirange ci_range; /* VPI/VCI range */
+ struct k_atm_dev_stats stats; /* statistics */
+@@ -359,7 +382,9 @@
+ struct proc_dir_entry *proc_entry; /* proc entry */
+ char *proc_name; /* proc entry name */
+ #endif
++#if !defined(CONFIG_MIPS_BCM963XX)
+ struct class_device class_dev; /* sysfs class device */
++#endif
+ struct list_head dev_list; /* linkage */
+ };
+
+@@ -416,7 +441,13 @@
+ int number,unsigned long *flags); /* number == -1: pick first available */
+ struct atm_dev *atm_dev_lookup(int number);
+ void atm_dev_deregister(struct atm_dev *dev);
++#if defined(CONFIG_MIPS_BCM963XX)
++void shutdown_atm_dev(struct atm_dev *dev);
++#endif
+ void vcc_insert_socket(struct sock *sk);
++#if defined(CONFIG_MIPS_BCM963XX)
++void vcc_remove_socket(struct sock *sk);
++#endif
+
+
+ /*
+@@ -432,20 +463,33 @@
+
+ static inline void atm_force_charge(struct atm_vcc *vcc,int truesize)
+ {
++#if defined(CONFIG_MIPS_BCM963XX)
++ atomic_add(truesize, &vcc->sk->sk_rmem_alloc);
++#else
+ atomic_add(truesize, &sk_atm(vcc)->sk_rmem_alloc);
++#endif
+ }
+
+
+ static inline void atm_return(struct atm_vcc *vcc,int truesize)
+ {
++#if defined(CONFIG_MIPS_BCM963XX)
++ atomic_sub(truesize, &vcc->sk->sk_rmem_alloc);
++#else
+ atomic_sub(truesize, &sk_atm(vcc)->sk_rmem_alloc);
++#endif
+ }
+
+
+ static inline int atm_may_send(struct atm_vcc *vcc,unsigned int size)
+ {
++#if defined(CONFIG_MIPS_BCM963XX)
++ return (size + atomic_read(&vcc->sk->sk_wmem_alloc)) <
++ vcc->sk->sk_sndbuf;
++#else
+ return (size + atomic_read(&sk_atm(vcc)->sk_wmem_alloc)) <
+ sk_atm(vcc)->sk_sndbuf;
++#endif
+ }
+
+
+@@ -457,12 +501,20 @@
+
+ static inline void atm_dev_put(struct atm_dev *dev)
+ {
++#if defined(CONFIG_MIPS_BCM963XX)
++ atomic_dec(&dev->refcnt);
++
++ if ((atomic_read(&dev->refcnt) == 1) &&
++ test_bit(ATM_DF_CLOSE,&dev->flags))
++ shutdown_atm_dev(dev);
++#else
+ if (atomic_dec_and_test(&dev->refcnt)) {
+ BUG_ON(!test_bit(ATM_DF_REMOVED, &dev->flags));
+ if (dev->ops->dev_close)
+ dev->ops->dev_close(dev);
+ class_device_put(&dev->class_dev);
+ }
++#endif
+ }
+
+
--- /dev/null
+diff -urN linux-2.6.19.2/drivers/mtd/chips/jedec_probe.c linux-2.6.19.2.new/drivers/mtd/chips/jedec_probe.c
+--- linux-2.6.19.2/drivers/mtd/chips/jedec_probe.c 2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2.new/drivers/mtd/chips/jedec_probe.c 2007-04-09 22:33:05.000000000 +0200
+@@ -158,6 +158,7 @@
+ #define SST49LF030A 0x001C
+ #define SST49LF040A 0x0051
+ #define SST49LF080A 0x005B
++#define SST39VF6402B 0x236C
+
+ /* Toshiba */
+ #define TC58FVT160 0x00C2
+@@ -1494,7 +1495,23 @@
+ ERASEINFO(0x1000,256),
+ ERASEINFO(0x1000,256)
+ }
+-
++ }, {
++ .mfr_id = MANUFACTURER_SST,
++ .dev_id = SST39VF6402B,
++ .name = "SST 39VF6402B",
++ .uaddr = {
++ [0] = MTD_UADDR_0x5555_0x2AAA, /* x8 */
++ [1] = MTD_UADDR_0x5555_0x2AAA /* x16 */
++ },
++ .DevSize = SIZE_8MiB,
++ .CmdSet = P_ID_AMD_STD,
++ .NumEraseRegions= 4,
++ .regions = {
++ ERASEINFO(0x2000,256),
++ ERASEINFO(0x2000,256),
++ ERASEINFO(0x2000,256),
++ ERASEINFO(0x2000,256)
++ }
+ }, {
+ .mfr_id = MANUFACTURER_ST, /* FIXME - CFI device? */
+ .dev_id = M29W800DT,
--- /dev/null
+#
+# Copyright (C) 2006 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/Atheros
+ NAME:=Atheros WiFi (default)
+ PACKAGES:=kmod-madwifi
+endef
+
+define Profile/Atheros/Description
+ Package set compatible with hardware using Atheros WiFi cards
+endef
+$(eval $(call Profile,Atheros))
+
--- /dev/null
+#
+# Copyright (C) 2006 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/Broadcom
+ NAME:=Broadcom WiFi (default)
+ PACKAGES:=kmod-net-bcm43xx
+endef
+
+define Profile/Broadcom/Description
+ Package set compatible with hardware using Broadcom WiFi cards
+endef
+$(eval $(call Profile,Broadcom))
+
--- /dev/null
+#
+# Copyright (C) 2006 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/Ralink
+ NAME:=Ralink WiFi
+ PACKAGES:=kmod-rt61
+endef
+$(eval $(call Profile,Ralink))
+
projects / librecmc / librecmc.git / commitdiff