#define CONFIG_ACADIA 1 /* Board is Acadia */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_405EZ 1 /* Specifc 405EZ support*/
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME acadia
+#include "amcc-common.h"
+
/* Detect Acadia PLL input clock automatically via CPLD bit */
#define CONFIG_SYS_CLK_FREQ ((in8(CFG_CPLD_BASE + 0) == 0x0c) ? \
66666666 : 33333000)
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xfe000000
#define CFG_CPLD_BASE 0x80000000
#define CFG_NAND_ADDR 0xd0000000
#define CFG_USB_HOST 0xef603000 /* USB OHCI 1.1 controller */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1)
-#define CFG_MALLOC_LEN (512 * 1024)/* Reserve 512 kB for malloc() */
-
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer
*----------------------------------------------------------------------*/
*----------------------------------------------------------------------*/
#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
#define CFG_BASE_BAUD 691200
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
-
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
/*-----------------------------------------------------------------------
* Environment
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
-#if 0 /* test-only... */
-/*-----------------------------------------------------------------------
- * SPI stuff - Define to include SPI control
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SPI
-#endif
-
/*-----------------------------------------------------------------------
* Ethernet
*----------------------------------------------------------------------*/
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
-#define CONFIG_NET_MULTI 1
-#define CFG_RX_ETH_BUFFER 16 /* # of rx buffers & descriptors*/
#define CONFIG_HAS_ETH0 1
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define xstr(s) str(s)
-#define str(s) #s
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=acadia\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=acadia/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"kernel_addr=fff10000\0" \
"ramdisk_addr=fff20000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 acadia/u-boot.bin\0" \
- "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
- "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
- "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "nload=tftp 200000 acadia/u-boot-nand.bin\0" \
- "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \
- "setenv filesize;saveenv\0" \
- "nupd=run nload nupdate\0" \
"kozio=bootm ffc60000\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_USB_OHCI
#define CONFIG_USB_STORAGE
#define CONFIG_SUPPORT_VFAT
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_USB
/*
#undef CONFIG_CMD_IMLS
#endif
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*-----------------------------------------------------------------------
* NAND FLASH
*----------------------------------------------------------------------*/
#define CFG_GPIO1_TSRL 0x00000000
#define CFG_GPIO1_TSRH 0x00000000
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
- #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME bamboo
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */
#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/
#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
* Serial Port
*----------------------------------------------------------------------*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* NVRAM/RTC
*
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_ENV_OFFSET 0x0
#endif /* CFG_ENV_IS_IN_EEPROM */
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=bamboo\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/bamboo/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"kernel_addr=fff00000\0" \
"ramdisk_addr=fff10000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/bamboo/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b 100000 fffa0000 60000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_HAS_ETH0
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
#define CONFIG_PHY1_ADDR 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#endif /* CONFIG_BAMBOO_NAND */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI 1 /* required for netconsole */
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
#ifdef CONFIG_440EP
/* USB */
#define CONFIG_USB_OHCI
#define USB_2_0_DEVICE
#endif /*CONFIG_440EP*/
-
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT2
#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
#ifdef CONFIG_BAMBOO_NAND
#define CONFIG_CMD_NAND
#endif
-
#define CONFIG_SUPPORT_VFAT
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CONFIG_LYNXKDI 1 /* support kdi files */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
/*-----------------------------------------------------------------------
* PCI stuff
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_BUBINGA 1 /* ...on a BUBINGA board */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME bubinga
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
#endif
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=bubinga\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/bubinga/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fff80000\0" \
"ramdisk_addr=fff90000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/bubinga/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */
-#define CONFIG_NET_MULTI 1
-#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Bubinga */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
/*
* If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
* If CFG_405_UART_ERRATA_59, then UART divisor is 31.
#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
#define CFG_BASE_BAUD 691200
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* I2C stuff
*-----------------------------------------------------------------------
*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_SRAM_BASE 0xFFF00000
#define CFG_FLASH_BASE 0xFFF80000
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
#define FPGA_REG1_OFFB_FLASH 0x02 /* Off board flash */
#define FPGA_REG1_SRAM_BOOT 0x01 /* SRAM at 0xFFF80000 not Flash */
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
/* This config file is used for Canyonlands (460EX) and Glacier (460GT) */
#ifndef CONFIG_CANYONLANDS
#define CONFIG_460GT 1 /* Specific PPC460GT */
+#define CONFIG_HOSTNAME glacier
#else
#define CONFIG_460EX 1 /* Specific PPC460EX */
+#define CONFIG_HOSTNAME canyonlands
#endif
#define CONFIG_440 1
#define CONFIG_4xx 1 /* ... PPC4xx family */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
+
#define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-
#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE
#define CFG_AHB_BASE 0xE2000000 /* internal AHB peripherals */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc()*/
-
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in OCM)
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
#undef CONFIG_UART1_CONSOLE /* define this if you want console on UART1 */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_SPEED 400000 /* I2C speed */
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
* Ethernet
*----------------------------------------------------------------------*/
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
#define CONFIG_PHY1_ADDR 1
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH2
#define CONFIG_HAS_ETH3
#endif
-#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_PHY_DYNAMIC_ANEG 1
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
/*-----------------------------------------------------------------------
* USB-OHCI
*----------------------------------------------------------------------*/
#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
#endif
-/*-----------------------------------------------------------------------
- * Default environment
- *----------------------------------------------------------------------*/
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-/* Setup some board specific values for the default environment variables */
-#ifdef CONFIG_CANYONLANDS
-#define CONFIG_HOSTNAME canyonlands
-#define CFG_BOOTFILE "bootfile=canyonlands/uImage\0"
-#define CFG_DTBFILE "fdt_file=canyonlands/canyonlands.dtb\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0"
-#else
-#define CONFIG_HOSTNAME glacier
-#define CFG_BOOTFILE "bootfile=glacier/uImage\0"
-#define CFG_DTBFILE "fdt_file=glacier/glacier.dtb\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0"
-#endif
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- CFG_BOOTFILE \
- CFG_DTBFILE \
- CFG_ROOTPATH \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "run nfsargs addip addtty;" \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "kernel_addr_r=400000\0" \
- "fdt_addr_r=800000\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"kernel_addr=fc000000\0" \
"fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 ${hostname}/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b ${fileaddr} fffa0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "nload=tftp 200000 ${hostname}/u-boot-nand.bin\0" \
- "nupdate=nand erase 0 100000;nand write 200000 0 100000;" \
- "setenv filesize;saveenv\0" \
- "nupd=run nload nupdate\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SNTP
#ifdef CONFIG_460EX
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
-#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#endif
-
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
}
#endif
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME ebony
+#include "amcc-common.h"
+
/*
* Define here the location of the environment variables (FLASH or NVRAM).
* Note: DENX encourages to use redundant environment in FLASH. NVRAM is only
*----------------------------------------------------------------------*/
#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xff800000 /* start of FLASH */
-#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
-
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE 115200
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400}
/*-----------------------------------------------------------------------
* NVRAM/RTC
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_EEPROM_PAGE_WRITE_BITS 3
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=ebony\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/ebony/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=ff800000\0" \
"ramdisk_addr=ff810000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/ebony/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 8 /* PHY address */
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_PHY1_ADDR 9 /* EMAC1 PHY address */
-#define CONFIG_NET_MULTI 1
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_440SPE 1 /* Specifc SPe support */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME katmai
+#include "amcc-common.h"
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xff000000 /* start of FLASH */
#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */
#define CFG_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1)
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */
-
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in internal SRAM)
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#define CONFIG_SERIAL_MULTI 1
#undef CONFIG_UART1_CONSOLE
#undef CFG_EXT_SERIAL_CLOCK
-#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*-----------------------------------------------------------------------
* DDR SDRAM
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_I2C_CMD_TREE
*----------------------------------------------------------------------*/
#define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define xstr(s) str(s)
-#define str(s) #s
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=katmai\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "net_nfs_fdt=tftp 200000 ${bootfile};" \
- "tftp ${fdt_addr} ${fdt_file};" \
- "run nfsargs addip addtty;" \
- "bootm 200000 - ${fdt_addr}\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=katmai/uImage\0" \
- "fdt_file=katmai/katmai.dtb\0" \
- "fdt_addr=400000\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fff10000\0" \
"ramdisk_addr=fff20000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 katmai/u-boot.bin\0" \
- "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
- "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
- "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
"kozio=bootm ffc60000\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
#define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_HAS_ETH0
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_RESET_DELAY 1000
#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* needed for NetConsole */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */
/*-----------------------------------------------------------------------
* FLASH related
#define CFG_GPIO_TCR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF)
#define CFG_GPIO_ODR 0
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_405EX 1 /* Specifc 405EX support*/
#define CONFIG_SYS_CLK_FREQ 33333333 /* ext frequency to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME kilauea
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_BOARD_EMAC_COUNT
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFC000000
#define CFG_NAND_ADDR 0xF8000000
#define CFG_FPGA_BASE 0xF0000000
#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */
-#define CFG_MONITOR_BASE (TEXT_BASE)
/*-----------------------------------------------------------------------
* Initial RAM & Stack Pointer Configuration Options
* Serial Port
*----------------------------------------------------------------------*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
#define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */
*----------------------------------------------------------------------*/
#define CONFIG_M88E1111_PHY 1
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_HAS_ETH0 1
-#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 2
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"logversion=2\0" \
- "netdev=eth0\0" \
- "hostname=kilauea\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_self_old=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "flash_nfs_old=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \
- "run nfsargs addip addtty;bootm ${kernel_addr_r}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "run nfsargs addip addtty;" \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=kilauea/uImage\0" \
- "fdt_file=kilauea/kilauea.dtb\0" \
- "kernel_addr_r=400000\0" \
- "fdt_addr_r=800000\0" \
"kernel_addr=fc000000\0" \
"fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 kilauea/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b ${fileaddr} fffa0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "nload=tftp 200000 kilauea/u-boot-nand.bin\0" \
- "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \
- "setenv filesize;saveenv\0" \
- "nupd=run nload nupdate\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
#define CONFIG_CMD_LOG
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SNTP
/* POST support */
#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
/* base address of inbound PCIe window */
#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
} \
}
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
/*-----------------------------------------------------------------------
* Some Kilauea stuff..., mainly fpga registers
*/
#define CFG_FPGA_USER_LED0 0x00000200
#define CFG_FPGA_USER_LED1 0x00000100
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_440 1
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME luan
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
-#define CFG_SDRAM_BASE 0x00000000 /* MUST be zero */
-
#define CFG_LARGE_FLASH 0xffc00000 /* 4MB flash address CS0 */
#define CFG_SMALL_FLASH 0xff900000 /* 1MB flash address CS2 */
#define CFG_SRAM_BASE 0xff800000 /* 1MB SRAM address CS2 */
* Serial Port
*----------------------------------------------------------------------*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* external 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#undef CONFIG_SERIAL_MULTI
#undef CONFIG_UART1_CONSOLE /* define if you want console on UART1 */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_EEPROM_PAGE_WRITE_BITS 3
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=luan\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
- "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm $(kernel_addr)\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/luan/uImage\0" \
+/*
+ * Default environment variables
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fc000000\0" \
"ramdisk_addr=fc100000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/luan/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_HAS_ETH0
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1
#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* needed for NetConsole */
-
#ifdef DEBUG
#define CONFIG_PANIC_HANG
#else
#endif
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#undef CONFIG_LYNXKDI /* support kdi files */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
#endif
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_405EX 1 /* Specifc 405EX support*/
#define CONFIG_SYS_CLK_FREQ 33330000 /* ext frequency to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME makalu
+#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0"
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFC000000
#define CFG_FPGA_BASE 0xF0000000
#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */
-#define CFG_MONITOR_BASE (TEXT_BASE)
/*-----------------------------------------------------------------------
* Initial RAM & Stack Pointer Configuration Options
* Serial Port
*----------------------------------------------------------------------*/
#undef CFG_EXT_SERIAL_CLOCK /* no ext. clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
#define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */
*----------------------------------------------------------------------*/
#define CONFIG_M88E1111_PHY 1
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 6 /* PHY address, See schematics */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_HAS_ETH0 1
-#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 0
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "logversion=2\0" \
- "netdev=eth0\0" \
- "hostname=makalu\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0" \
- "flash_self_old=run ramargs addip addtty addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "flash_self=run ramargs addip addtty addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "flash_nfs_old=run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr}\0" \
- "flash_nfs=run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \
- "run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr_r}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=makalu/uImage\0" \
- "fdt_file=makalu/makalu.dtb\0" \
- "kernel_addr_r=400000\0" \
- "fdt_addr_r=800000\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fc000000\0" \
"fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 makalu/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b ${fileaddr} fffa0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
#define CONFIG_CMD_LOG
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SNTP
/* POST support */
#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
/* base address of inbound PCIe window */
#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
#define CFG_GPIO_PCIE_CLKREQ 27
#define CFG_GPIO_PCIE_WAKE 28
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
projects / oweals / u-boot.git / commitdiff