-commit 467bcee11fe26ad422f2de971aa70866079870f2
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Fri Dec 14 15:36:18 2007 +0100
+commit b2e2142c500c48a57f18f9dd30e66c13caea0971
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Jan 9 10:38:58 2008 +0100
- cfi_flash: Add manufacturer-specific fixups
+ POST: Execute SPR test after relocation
- Run fixups based on the JEDEC manufacturer ID independent of the
- command set ID.
+ On LWMON5 we now use d-cache as init-ram and stack. The SPR POST test uses
+ self modifying code and this doesn't work with stack in d-cache, since
+ I can't move the code from d-cache to i-cache. We move the SPR test to
+ be executed a little later, after relocation. Then stack is located in
+ SDRAM and this self-modifying code is no problem anymore.
- This changes current behaviour: Previously, geometry reversal for AMD
- chips were done based on the command set ID, while they are now done
- based on the JEDEC manufacturer and device ID.
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Also add fixup for top-boot Atmel chips. A fixup is needed for
- AT49BV6416(T) too, but since u-boot currently only reads the low byte
- of the device ID, there's no way to tell it apart from AT49BV642D,
- which should not have this fixup. Since AT49BV642D support is
- necessary to get ATNGW100 board support into mainline, I've commented
- out the fixup for now.
+commit 8f24e0637ae113500d8bd60d80d57afcc0aa8bde
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Jan 9 10:28:20 2008 +0100
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ ppc4xx: Change LWMON5 to not use OCM for init-ram and POST anymore
-commit 0ddf06ddf6b4bd057ad4c5f0dffea7870ba06a2a
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Fri Dec 14 15:36:17 2007 +0100
+ This patch configures the LWMON5 port to use d-cache as init-ram and
+ the unused GPT0_COMP6 as POST WORD storage.
- cfi_flash: Add cmdset-specific init functions
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Move things like reading JEDEC IDs and fixing up geometry reversal
- into separate functions. The geometry reversal fixup is now performed
- by altering the qry structure directly, which makes the sector init
- code slightly cleaner.
+commit 1754f50b710194f886b6f2831803d8960171a14d
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Jan 9 10:25:46 2008 +0100
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ ppc4xx: Add CFG_POST_ALT_WORD_ADDR to support non OCM POST WORD storage
-commit e23741f4a6d8047520ef0d4971762749b3587d32
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Fri Dec 14 15:36:16 2007 +0100
+ The privious 4xx POST implementation only supported storing the POST
+ WORD in OCM. Since we need to reserve the OCM on LWMON5 for the logbuffer
+ we need to store the POST WORD in some other non volatile location.
+ This patch adds CFG_POST_ALT_WORD_ADDR to specify an address for such
+ a location.
- cfi_flash: Read whole QRY structure in one go
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Read out the whole CFI Standard Query structure after successful cfi
- identification. This allows subsequent code to access this information
- directly without having to go through flash_read_uchar() and friends.
+commit e02c521d94b45d7b05aa522e4ccde6b74bf5fe57
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Jan 9 10:23:16 2008 +0100
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ ppc4xx: Add 44x cache locking to better support init-ram in d-cache
-commit df9c25ea04b38a0e05d4f8c73c5cc144cdafa7db
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Mon Dec 17 11:02:44 2007 +0100
+ This patch adds support for locking the init-ram/stack in d-cache,
+ so that other regions may use d-cache as well
- AVR32: Fix logic inversion in disable_interrupts()
+ Note, that this current implementation locks exactly 4k of d-cache,
+ so please make sure that you don't define a bigger init-ram area. Take
+ a look at the lwmon5 440EPx implementation as a reference.
- disable_interrupts() should return nonzero if interrupts were
- _enabled_ before, not disabled.
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+commit 0ddb89601a8d29e808db450366752ffdc6267c53
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed Jan 9 10:16:33 2008 +0100
-commit acac475212cbedb17b321a363a1c878e2b47b37f
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Fri Dec 14 16:51:22 2007 +0100
+ Fix memset bug in ext2fs_read_file()
- AVR32: Enable interrupts at bootup
+ ext2fs_read_file() had the function arguments swapped.
- The timer code depends on the timer interrupt to keep track of the
- upper 32 bits of the cycle counter. This obviously doesn't work when
- interrupts are disabled the whole time.
+ Pointed out by Mike Montour, 19 Dec 2007 22:34:25 -0800
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
-commit 9570bcd87f4db255514f43b6701746c412f8fef0
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Thu Nov 15 10:03:45 2007 +0100
+commit 32d6f1bc09175f3b77469771e839bc7255a9f22e
+Author: Markus Klotzbücher <mk@denx.de>
+Date: Tue Jan 5 08:17:15 1988 +0100
- AVR32: Fix wrong pin setup for USART3
+ Fix problems with usb storage devices on MPC5200 /TQM5200
- As reported by Gerhard Berghofer:
+ The MPC5200 OHCI controller operates in big endian, so
+ CFG_OHCI_BE_CONTROLLER must be defined for it to work properly.
- in "gpio_enable_usart3" the correct pins for USART 3 are PB17 and PB18
- instead of PB18 and PB19.
+ Signed-off-by: Markus Klotzbuecher <mk@denx.de>
- which is obviously correct. There's currently no code that uses
- USART3, but custom boards may run into problems.
+commit 46f6e5019048b103d7693d5310de0f1cfbaf4c19
+Author: Wolfgang Denk <wd@denx.de>
+Date: Tue Jan 8 22:58:27 2008 +0100
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ Fix compile problem with new env code.
-commit 09ea0de03dcc3ee7af045b0b572227bda2c1c918
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Thu Nov 1 12:44:20 2007 +0100
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
- README: Remove ATSTK1000 daughterboard list
+commit 64b3727b9779d86127cd576e392a987de5ebb9fd
+Author: Markus Klotzbücher <mk@denx.de>
+Date: Tue Nov 27 10:23:20 2007 +0100
- As noted by Kim Phillips, these lists tend to become out of date.
+ tools: fix fw_printenv tool to compile again
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ This patch updates the fw_printenv/fw_setenv userspace tool to include
+ the correct MTD header in order to compile against current kernel
+ headers. Backward compatibility is preserved by introducing an option
+ MTD_VERSION which can be set to "old" for compilation using the old MTD
+ headers. Along with this a number of warnings are fixed.
-commit c81cbbad21cb0ae983e2e796211202234cdc8be2
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Tue Oct 30 14:56:36 2007 +0100
+ Signed-off-by: Markus Klotzbuecher <mk@denx.de>
- Add ATSTK100[234] to MAINTAINERS
+commit 1f84021a85abeb837d2ce0dc84297b4f1d45d516
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Tue Jan 8 15:40:09 2008 +0100
- Add all the ATSTK1000 daughterboards to MAINTAINERS along with their
- "mother". Also update the entry for ATSTK1000 to be not only about the
- AP7000 CPU; it's intended to handle all CPUs in the AT32AP family.
+ ppc4xx: assign PCI interrupts on seuqoia boards
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ Some operating systems rely on assigned PCI interrupts.
-commit 64ff2357b1727213803591813dbc779c924bf772
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Mon Oct 29 13:02:54 2007 +0100
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
- AVR32: Add support for the ATSTK1004 board
+commit 6e9233d30afe57cb6e148fbfa4895e7810196fac
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Tue Jan 8 15:50:49 2008 +0100
- ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU,
- which is a derivative of AT32AP7000.
+ ppc4xx: Move cpu/ppc4xx/vecnum.h into include path
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ This patch allows the use of 4xx interrupt vector number defines
+ in board specific code outside cpu/ppc4xx.
-commit 667568db157f374b85abd7e03596ddd1f0b25681
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Mon Oct 29 13:02:54 2007 +0100
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
- AVR32: Add support for the ATSTK1003 board
+commit 580d1d3186a2bc6dbdb626941b716dae1788e51e
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Tue Jan 8 15:39:01 2008 +0100
- ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU,
- which is a derivative of AT32AP7000.
+ ppc4xx: Fix UIC2 vector number base
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
-commit 5fee84a794a51ec830548cda485a770efb018b92
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Mon Oct 29 13:23:33 2007 +0100
+commit ff5fb8a6ccba56e3482d0e297d8cfb7faa040811
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Tue Jan 8 12:49:58 2008 +0100
- AVR32: Make some AT32AP700x peripherals optional
+ ppc4xx: Update PLB/PCI divider for PMC440 board
- Add a chip-features file providing definitions of the form
+ This patch updates the PLB/PCI divider when running at
+ 400MHz CPU frequency from 4 to 3 which results in 44MHz PCI sync clock.
- AT32AP700x_CHIP_HAS_<peripheral>
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
- to indicate the availability of the given peripheral on the currently
- selected chip.
+commit 7d5d75633174867316a0c0f2fca5ceb2cf312cde
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Tue Jan 8 11:13:09 2008 +0100
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ ppc4xx: Disable error message when no NAND chip is installed on PMC440
-commit 36f28f8a9605ee5dcfa330482cfc62171261af97
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Mon Oct 29 13:09:56 2007 +0100
+ Add CFG_NAND_QUIET_TEST option to disable error message when
+ no NAND chip is installed on PMC440 boards.
- AVR32: Rename at32ap7000 -> at32ap700x
+ Disable a couple of config defines that are only used for NAND_U_BOOT.
- The SoC-specific code for all the AT32AP700x CPUs is practically
- identical; the only difference is that some chips have less features
- than others. By doing this rename, we can add support for the AP7000
- derivatives simply by making some features conditional.
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+commit ad3006fe7e84667021753b74247b0bafd97ba35f
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Mon Jan 7 23:47:32 2008 -0500
-commit 4d5fa99c73f354e7cf985efcf417ea55ca2f6a5e
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Fri Jun 29 18:22:34 2007 +0200
+ LIBFDT: use memmove() instead of memcpy()
- atmel_mci: Show SR when block read fails
+ This is partial patch from the DTC/libfdt
+ commit 67b6b33b9b413a450a72135b5dc59c0a1e33e647
+ Author: David Gibson <david@gibson.dropbear.id.au>
+ Date: Wed Nov 21 11:56:14 2007 +1100
- Show controller status as well as card status when an error occurs
- during block read.
+ The patch also fixes one genuine bug caught by valgrind -
+ _packblocks() in fdt_rw.c was using memcpy() where it should have been
+ using memmove().
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
-commit 12d30aa79779c2aa7a998bbae4c075f822a53004
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Thu Dec 13 12:56:34 2007 +0100
+commit aec7135bc300e3340d18f203347ee00c5b5f68c0
+Author: David Gibson <david@gibson.dropbear.id.au>
+Date: Mon Dec 17 14:42:07 2007 +1100
- cfi_flash: Use map_physmem() and unmap_physmem()
+ libfdt: Add more documentation (patch the seventh)
- Use map_physmem() and unmap_physmem() to convert from physical to
- virtual addresses. This gives the arch a chance to provide an uncached
- mapping for flash accesses.
+ This patch adds more documenting comments to libfdt.h. Specifically,
+ these document the read/write functions (not including fdt_open_into()
+ and fdt_pack(), for now).
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
-commit 4d7d6936eb29af7cca330937808312aa5f61454d
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Thu Dec 13 12:56:33 2007 +0100
+commit 9d4450b5adc36623e9c1de1f92539db77ad0c57e
+Author: David Gibson <david@gibson.dropbear.id.au>
+Date: Mon Dec 17 14:41:52 2007 +1100
- Introduce map_physmem() and unmap_physmem()
+ libfdt: Add more documentation (patch the sixth)
- map_physmem() returns a virtual address which can be used to access a
- given physical address without involving the cache. unmap_physmem()
- should be called when the virtual address returned by map_physmem() is
- no longer needed.
+ This patch adds some more documenting comments to libfdt.h.
+ Specifically this documents all the write-in-place functions.
- This patch adds a stub implementation which simply returns the
- physical address cast to a uchar * for all architectures except AVR32,
- which converts the physical address to an uncached virtual mapping.
- unmap_physmem() is a no-op on all architectures, but if any
- architecture needs to do such mappings through the TLB, this is the
- hook where those TLB entries can be invalidated.
+ Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+commit b60af3d4c1680487ee37e11aa1b3db6dec04d8f0
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Sat Dec 29 22:45:27 2007 -0500
-commit cdbaefb5f5f03e54455d0439dcf6dbd97ead1f9d
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Thu Dec 13 12:56:32 2007 +0100
+ Fine grained per property /chosen updating.
- cfi_flash: Introduce read and write accessors
+ Implement a suggestion by Scott Wood to make the /chosen handling fine
+ grained. Don't overwrite pre-existing properties on a per-property basis,
+ so if /chosen exists but a necessary /chosen/property doesn't, it gets
+ created. If a /chosen property exists, it is NOT overwritten unless the
+ "force" flag is true.
- Introduce flash_read{8,16,32,64) and flash_write{8,16,32,64} and use
- them to access the flash memory. This makes it clearer when the flash
- is actually being accessed; merely dereferencing a volatile pointer
- looks just like any other kind of access.
+ Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+commit 238cb7a423c6eaa36496efb788cfb9798cea7f95
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Sat Jan 5 15:33:29 2008 -0500
-commit 812711ce6b3a386125dcf0d6a59588e461abbb87
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Thu Dec 13 12:56:31 2007 +0100
+ Improve the FDT help message.
- Implement __raw_{read,write}[bwl] on all architectures
+ Add a note that "fdt copy" makes the new address active.
+ Remove most of the extra hints at the end of the fdt help.
- This adds implementations of __raw_read[bwl] and __raw_write[bwl] to
- m68k, ppc, nios and nios2. The m68k and ppc implementations were taken
- from Linux.
+ Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+commit ea6d8be153ceaf16958f8009cea6d75f3ff58d92
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Sat Jan 5 14:52:04 2008 -0500
-commit be60a9021c82fc5aecd5b2b1fc96f70a9c81bbcd
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Sat Oct 6 18:55:36 2007 +0200
+ Support setting FDT properties with optional values.
- cfi_flash: Reorder functions and eliminate extra prototypes
+ Fix a bug found and documented by Bartlomiej Sieka where the optional
+ value on "fdt set <path> <prop> [<val>]" wasn't optional.
- Reorder the functions in cfi_flash.c so that each function only uses
- functions that have been defined before it. This allows the static
- prototype declarations near the top to be eliminated and might allow
- gcc to do a better job inlining functions.
+ => fdt mknode / testnode
+ => fdt print /testnode
+ testnode {
+ };
+ => fdt set /testnode testprop
+ => fdt print /testnode
+ testnode {
+ testprop;
+ };
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
-commit 3055793bcbdf24b1f8117f606ffb766d32eb766f
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Thu Dec 13 12:56:29 2007 +0100
+commit 22fb2246df91bfc840d87f0c5910818bad55577a
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Fri Dec 28 11:56:30 2007 +0100
- cfi_flash: Make some needlessly global functions static
+ Add fdt_find_and_setprop() to fdt_support.h
- Make functions not declared in any header file static.
+ fdt_find_and_setprop() is used by several 4xx boards and it's
+ missing in the appropriate header. This patch eliminates a
+ warning when building U-Boot for such boards.
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+ Acked-by: Stefan Roese <sr@denx.de>
-commit 7e5b9b471518c5652febc68ba62b432193d6abf4
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Thu Dec 13 12:56:28 2007 +0100
+commit 802b769bac17b0560d3535a42c502469ee190cd1
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Jan 8 18:39:30 2008 +0100
- cfi_flash: Break long lines
+ ppc4xx: Return 0 on success in 4xx ethernet driver
- This patch tries to keep all lines in the cfi_flash driver below 80
- columns. There are a few lines left which don't fit this requirement
- because I couldn't find any trivial way to break them (i.e. it would
- take some restructuring, which I intend to do in a later patch.)
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+commit 6775c68683a53c7abc778774641aac6f833a2cbf
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Tue Jan 8 09:59:49 2008 -0600
-commit 42026c9cb3a76849b41e6e24abfb7b56807a5c1a
-Author: Bartlomiej Sieka <tur@semihalf.com>
-Date: Tue Dec 11 13:59:57 2007 +0100
+ mpc83xx: fix missed pci_hose -> hose conversion for new libfdt code
- CFI: synchronize command offsets with Linux CFI driver
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- Fixes non-working CFI Flash on the Inka4x0 board.
+commit 94fab25f5f1a7d1c0cc63c17e813ea8943fe49c7
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Thu Dec 20 16:28:34 2007 -0600
- Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
+ mpc83xx: rm remaining FLAT_TREE code
-commit 8ff3de61fc5f9b3b21647bce081a3b7f710f0d4d
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Fri Dec 7 12:17:34 2007 -0600
+ ..in board pci.c files
- Handle MPC85xx PCIe reset errata (PCI-Ex 38)
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- On the MPC85xx boards that have PCIe enable the PCIe errata fix.
- (MPC8544DS, MPC8548CDS, MPC8568MDS).
+commit b3458d2cd55d01732e30a76d898afd99e871cd67
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Thu Dec 20 15:57:28 2007 -0600
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ mpc83xx: remove FLAT_TREE code
-commit 82ac8c97145a4c3bf8b3dbfad00fa96e920f9b9c
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Fri Dec 7 12:04:30 2007 -0600
+ need to rm it from pci code, too!
- Update Freescale MPC85xx ADS/CDS/MDS board config
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- * Enabled CONFIG_CMD_ELF
+commit 5b8bc606c61456566af6912f818a153b6b06f242
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Thu Dec 20 14:09:22 2007 -0600
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ mpc83xx: convert to using do_fixup_*()
-commit d435793229ce29a42797c1edc39f5b34f987f91a
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Fri Dec 7 04:59:26 2007 -0600
+ convert to using simpler mpc85xx style fdt update code; streamline by
+ eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm
+ the old school FLAT_TREE code from 83xx (since the sbc8349 was just
+ converted over to using libfdt).
- Handle Asynchronous DDR clock on 85xx
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- The MPC8572 introduces the concept of an asynchronous DDR clock with
- regards to the platform clock.
+commit e496865ecc31a2fe2f9abfe798334bb02aaf05ab
+Author: Paul Gortmaker <paul.gortmaker@windriver.com>
+Date: Thu Dec 20 12:58:51 2007 -0500
- Introduce get_ddr_freq() to report the DDR freq regardless of sync/async
- mode.
+ sbc8349: enable libfdt by default on WRS SBC8349 board.
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ Make libfdt the default for the WRS SBC8349 board.
+ Parallel of commit 35cc4e4823668e8745854899cfaedd4489beb0ef
+ done for the other 83xx based boards. Also fix a typo in CONFIG_PCI.
-commit 22abb2d2eaf7b795a6923c6273ec9cb53fda9a10
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Thu Nov 29 10:34:28 2007 -0600
+ Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
- Update Freescale MPC85xx ADS/CDS/MDS board config
+commit 2408b3f20bcbdd9c6c397cd03ab0d71d54680a40
+Author: Paul Gortmaker <paul.gortmaker@windriver.com>
+Date: Thu Dec 20 12:58:16 2007 -0500
- * Removed some misc environment setup
- * Enabled CONFIG_CMDLINE_EDITING
+ sbc8349: migrate board to libfdt
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ This adds libfdt support code for the Wind River sbc8349 board.
-commit 415a613babb84d5e5d5b42e8e553868c71fc3a64
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Thu Nov 29 10:47:44 2007 -0600
+ Parallel of commit 3fde9e8b22cfbd7af489214758f9839a206576cb for
+ the other Freescale 83xx boards.
- Move the MPC8541/MPC8555/MPC8548 CDS board under board/freescale.
+ Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
- Minor path corrections needed to ensure buildability.
+commit 27a256a90cc86392ac9bf0039a3afe638ec2c18d
+Author: Paul Gortmaker <paul.gortmaker@windriver.com>
+Date: Thu Dec 20 12:56:19 2007 -0500
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ sbc8349: Remove board specific ECC code
-commit c2d943ffbfd3359b3b45d177b437379d2cb86fbf
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Thu Nov 29 10:16:18 2007 -0600
+ ECC code is now shared for all 83xx boards, so remove board specific one.
+ See commit daab8c67d2defef73dc26ab07f0c3afd1b05d019 for reference.
- Move the MPC8540 ADS board under board/freescale.
+ Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
- Minor path corrections needed to ensure buildability.
+commit a1e1ac849249310e5e2e5c7148e9fb353a8317a7
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Thu Dec 20 01:30:48 2007 -0600
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ mpc83xx: Remove CONFIG options related to OF that we dont use (on 837x)
-commit 870ceac5b3a3486c109396e005af81ae762b5710
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Thu Nov 29 10:14:50 2007 -0600
+ continuation of commit 37395fa2b0d9d617f28d44ca11592260ef16105a to 837x
- Move the MPC8560 ADS board under board/freescale.
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- Minor path corrections needed to ensure buildability.
+commit ccf21c311e68d48399eff1e72936052885f6e3f7
+Author: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
+Date: Thu Dec 6 16:43:40 2007 +0100
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ Add support CONFIG_UEC_ETH3 in MPC83xx
-commit acbca876fb3fec25cd9c55b0efc81ff618ff5262
+ Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
+
+commit e6af9932d31171e35db880e7b2f29f903b1b7660
Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Thu Nov 29 10:13:47 2007 -0600
+Date: Mon Nov 26 11:00:54 2007 -0600
- Move the MPC8568 MDS board under board/freescale.
+ Remove CONFIG options related to OF that we dont use
- Minor path corrections needed to ensure buildability.
+ The MPC8360E MDS config defined:
+ CONFIG_OF_HAS_BD_T
+ CONFIG_OF_HAS_UBOOT_ENV
+
+ Which we don't use or ever needed. This seems like copy-paste feature creep.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
-commit a853d56c59b33415304531443633808736acfc6e
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Thu Nov 29 02:18:59 2007 -0600
+commit f602082b4b7ed4ee16432067cc67a0a24fedc715
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Mon Dec 10 14:16:22 2007 -0600
- Use standard LAWAR_TRGT_IF_* defines for LAW setup on 85xx
+ mpc83xx: supress compiler warning
- We already had defines for LAWAR_TRGT_IF_* that we should use
- rather than creating new ones. Also, added some missing defines for
- PCIE targets.
+ mpc8360emds.c: In function ‘ft_board_setup’:
+ mpc8360emds.c:335: warning: assignment discards qualifiers from pointer target type
+ mpc8360emds.c:345: warning: assignment discards qualifiers from pointer target type
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
-commit 04db400892da37b76a585e332a0c137954ad2015
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Thu Nov 29 02:10:09 2007 -0600
+commit c16e44fa835fb9eec982d919863a04e2f78e5ce7
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Tue Nov 27 14:17:29 2007 -0600
- Stop using immap_t on 85xx
+ mpc83xx: fix remaining fdt_find_node_by_path references
- In the future the offsets to various blocks may not be in same location.
- Move to using CFG_MPC85xx_*_ADDR as the base of the registers
- instead of getting it via &immap.
+ rename to fdt_path_offset
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
-commit 2714223f8e04ab3e4133ff65872eef366d90bfea
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Thu Nov 29 01:23:09 2007 -0600
+commit 921d4b19ad1be704df58725485d9292dc0414adf
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Mon Nov 19 12:30:09 2007 -0600
- Remove CONFIG_OF_FLAT_TREE related code from mpc85xx since we now use libfdt
+ mpc83xx: fix CFG_ENV_ADDR and CFG_ENV_SECT_SIZE definitions for 837x
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for 837x.
+ This change guarantees that the environment will be located on the
+ first flash sector after the U-Boot image.
-commit c480861bf000156e6a3e932c258db59ff2212dd3
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Thu Nov 29 01:06:19 2007 -0600
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- Update MPC8568 MDS to use libfdt
+commit 24f868433b50ecbaa88e118aadc7bd254013c6ae
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Fri Nov 9 14:28:08 2007 -0600
- Updated the MPC8568 MDS config to use libfdt and assume use of aliases for
- ethernet, pci, and serial for the various fixups that are done.
+ mpc83xx: mpc8360 rev.2.1 erratum 2: replace rgmii-id with rgmii-rxid
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ u-boot itself uses GMII mode on the 8360. Fix up UCC phy-connection-type
+ properties in the device tree so the PHY gets configured for internal delay on
+ RX only by the OS, as prescribed by mpc8360 rev. 2.1 pb mds erratum #2.
-commit 1563f56e0c68f6920f956382d6d13bee3f01c0f7
-Author: Haiying Wang <Haiying.Wang@freescale.com>
-Date: Wed Nov 14 15:52:06 2007 -0500
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- Add PCI Express support on MPC8568MDS
+commit 22b448dbfbe2a98f01ff4adc3c3979f8c541ad7b
+Author: Dave Liu <r63238@freescale.com>
+Date: Tue Sep 18 12:41:15 2007 +0800
- Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ mpc83xx: update the CREDITS and MAINTAINERS
-commit b90d25497625b90ffa3f2911a0895ca237556ff5
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Thu Nov 29 00:11:44 2007 -0600
+ update the CREDITS and MAINTAINERS.
- Update MPC85xx CDS to use libfdt
+ Signed-off-by: Dave Liu <daveliu@freescale.com>
- Updated the MPC85xx CDS config to use libfdt and assume use of aliases for
- ethernet, pci, and serial for the various fixups that are done.
+commit b21add4b42af7b767448251b599b91066a160e0d
+Author: Dave Liu <r63238@freescale.com>
+Date: Tue Sep 18 12:40:21 2007 +0800
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ mpc83xx: add MAINTAINER and MAKEALL entries for the mpc837xemds
-commit 0fd5ec66b10521a057ad73e69ab5f0f9eafba255
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Wed Nov 28 22:54:27 2007 -0600
+ Add the MAINTAINER and MAKEALL entries for mpc837xemds
- Update MPC8540 ADS to use libfdt
+ Signed-off-by: Dave Liu <daveliu@freescale.com>
- Updated the MPC8540 ADS config to use libfdt and assume use of aliases for
- ethernet, pci, and serial for the various fixups that are done.
+commit f8900ce9094c462355eb792eea264ff16ac8fd16
+Author: Dave Liu <r63238@freescale.com>
+Date: Tue Sep 18 12:38:53 2007 +0800
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ mpc83xx: Add the MPC837xEMDS board readme
-commit 5ce715802f6c50dc78b3405b92f184b1e3710519
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Wed Nov 28 22:40:31 2007 -0600
+ Add the README.mpc837xemds to /doc
- Update MPC8560 ADS to use libfdt
+ Signed-off-by: Dave Liu <daveliu@freescale.com>
- Updated the MPC8560 ADS config to use libfdt and assume use of aliases for
- ethernet, pci, and serial for the various fixups that are done.
+commit 19580e660cc8da49f16536a8bd78c047c7bc12e5
+Author: Dave Liu <r63238@freescale.com>
+Date: Tue Sep 18 12:37:57 2007 +0800
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ mpc83xx: Add the support of MPC837xEMDS board
-commit aafeefbdb8b029f5ca2a195598d0a501a606eea9
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Wed Nov 28 00:36:33 2007 -0600
+ The MPC837xEMDS board support:
+ * DDR2 400MHz hardcoded and SPD init
+ * Local bus NOR Flash
+ * I2C, UART, MII and RTC
+ * eTSEC RGMII
+ * PCI host
- Stop using immap_t for cpm offset on 85xx
+ Signed-off-by: Dave Liu <daveliu@freescale.com>
- In the future the offsets to various blocks may not be in same location.
- Move to using CFG_MPC85xx_CPM_ADDR as the base of the CPM registers
- instead of getting it via &immap->im_cpm.
+commit 555da61702771fe0f76f3de23b4e7590f3704161
+Author: Dave Liu <r63238@freescale.com>
+Date: Tue Sep 18 12:36:58 2007 +0800
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ mpc83xx: Add the support of MPC8315E SoC
-commit f59b55a5b8fcadaa99781ba48e7a38e956afa527
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Tue Nov 27 23:25:02 2007 -0600
+ The MPC8315E SoC including e300c3 core and new IP blocks,
+ such as TDM, PCI Express and SATA controller.
- Stop using immap_t for guts offset on 85xx
+ Signed-off-by: Dave Liu <daveliu@freescale.com>
- In the future the offsets to various blocks may not be in same location.
- Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers
- instead of getting it via &immap->im_gur.
+commit 03051c3d35c9981ceaa059005660e699f3eacf1c
+Author: Dave Liu <r63238@freescale.com>
+Date: Tue Sep 18 12:36:11 2007 +0800
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ mpc83xx: Add the support of MPC837x SoC
-commit 50c03c8cf494d91cdec39670d95337c743e16ec9
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Tue Nov 27 22:42:34 2007 -0600
+ The MPC837x SoC including e300c4 core and new IP blocks,
+ such as SDHC, PCI Express and SATA controller.
- Update MPC8544 DS config
+ Signed-off-by: Dave Liu <daveliu@freescale.com>
- * Removed HAS_ETH2/HAS_ETH3 - MPC8544 only has TSEC1/2
- * Removed some misc environment setup
- * Moved to using fdtfile & fdtaddr as fdt env var names
- * Enabled CONFIG_CMDLINE_EDITING
+commit 651d96f7e4c84adcdb98ef07ec878c20326e3359
+Author: Anton Vorontsov <avorontsov@ru.mvista.com>
+Date: Wed Nov 14 18:54:53 2007 +0300
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ MPC8360E-MDS: configure and enable second UART
-commit addce57e2e4c49e77ffb2020a84690713bb18b47
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Mon Nov 26 17:12:24 2007 -0600
+ Despite user manual, BCSR9.7 is negated (high) on HRST, so
+ UART2 is disabled. Fix that and configure QE pins properly.
- Update MPC8544DS to use libfdt
+ Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
- Updated the MPC8544DS config to use libfdt and assume use of aliases for
- ethernet, pci, and serial for the various fixups that are done.
+commit b2893e1fcb28fad8c8b317104df8cee0142c7631
+Author: Timur Tabi <timur@freescale.com>
+Date: Mon Nov 5 09:34:06 2007 -0600
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ 83xx: fix CFG_ENV_ADDR and CFG_ENV_SECT_SIZE definitions
-commit f852ce72f100cabd1f11c21c085a0ad8eca9fb65
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Thu Nov 29 00:15:30 2007 -0600
+ Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for all of the
+ currently-defined 83xx boards. This change guarantees that the environment
+ will be located on the first flash sector after the U-Boot image.
- Add libfdt based ft_cpu_setup for mpc85xx
+ Signed-off-by: Timur Tabi <timur@freescale.com>
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+commit e05329516a13616b53240cd85b739217c2bf87f1
+Author: Larry Johnson <lrj@acm.org>
+Date: Fri Jan 4 13:27:02 2008 -0500
-commit 9692c2734a47f23b44a0f68042a3e2ca8d1bfb39
+ ppc4xx: Remove weak binding from common Denali data-eye search code
+
+ Now that there are no board-specific versions of
+ "denali_core_search_data_eye()", the weak binding on the common version
+ can be removed.
+
+ Signed-off-by: Larry Johnson <lrj@acm.org>
+
+commit 5ba576c01602fd328800a427964c36a0a05c5dce
Author: Stefan Roese <sr@denx.de>
-Date: Sat Dec 8 08:25:09 2007 +0100
+Date: Sat Jan 5 09:13:46 2008 +0100
- CFI: Coding style cleanup
+ ppc4xx: Remove unused CONFIG_ECC_ERROR_RESET from 44x_spd_ddr2.c
Signed-off-by: Stefan Roese <sr@denx.de>
-commit 81b20ccc2d795ae9a1199db5a50ad9c28d1e4d22
-Author: Michael Schwingen <michael@schwingen.org>
-Date: Fri Dec 7 23:35:02 2007 +0100
+commit 845c6c95dbfe6c915ce68a0a115852fa17932fb4
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Jan 5 09:12:41 2008 +0100
- CFI: support JEDEC flash roms in CFI-flash framework
+ ppc4xx: Update Katmai/44x_spd_ddr2.c code for optimal DDR2 setup
- The following patch adds support for non-CFI flash ROMS, by hooking into the
- CFI flash code and using most of its code, as recently discussed here in the
- thread "Mixing CFI and non-CFI flashs".
+ On Katmai the complete auto-calibration somehow doesn't seem to
+ produce the best results, meaning optimal values for RQFD/RFFD.
+ This was discovered by GDA using a high bandwidth scope,
+ analyzing the DDR2 signals. GDA provided a fixed value for RQFD,
+ so now on Katmai "only" RFFD is auto-calibrated.
+
+ This patch also adds RDCC calibration as mentioned on page 7 of
+ the AMCC PowerPC440SP/SPe DDR2 application note:
+ "DDR1/DDR2 Initialization Sequence and Dynamic Tuning"
- Signed-off-by: Michael Schwingen <michael@schwingen.org>
Signed-off-by: Stefan Roese <sr@denx.de>
-commit c01b17dd856fa120b2970f50d9598546a4927ec3
-Author: Gerald Van Baren <vanbaren@cideas.com>
-Date: Wed Nov 28 21:24:50 2007 -0500
+commit 49db47b8ae6afff2b898be312948ff501357dc80
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Wed Jan 2 16:48:42 2008 +0100
- Conditionally compile fdt_fixup_ethernet()
+ ppc4xx: Remove sdram.h from PMC440 board
- Fix compiler warnings: On boards that don't have ethernets defined,
- don't compile fdt_fixup_ethernet().
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
-commit 246d4ae6bc282bc1841224e1c5fc49dc925e0bf7
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Tue Nov 27 21:59:46 2007 -0600
+commit 34065a2ce0d8972f2ec6652076014ab243d2ce8a
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Wed Jan 2 16:48:34 2008 +0100
- Convert boards that set memory node to use fdt_fixup_memory()
+ ppc4xx: use common denali core defines and data eye search code for PMC440
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
-commit 151c8b09b35eebe8fd9139cb6c1d91c27b22f058
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Mon Nov 26 17:06:15 2007 -0600
+commit 9ac6b6f3d3f1b072d89268b2efe47e95e6659489
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Wed Jan 2 12:05:14 2008 +0100
- Added fdt_fixup_stdout that uses aliases to set linux,stdout-path
+ ppc4xx: More cleanup for esd's LCD code
- We use a combination of the serialN alias and CONFIG_CONS_INDEX to
- determine which serial alias we should set linux,stdout-path to.
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+commit fe9c26b330a21ce73e52b5bd347d725cb81e3cfb
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Jan 4 12:00:01 2008 +0100
-commit 3c9272813fad84c691d0e4989bb18a3ffebdebfc
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Mon Nov 26 14:57:45 2007 -0600
+ ppc4xx: Fix Sequoia NAND booting target
- Add common memory fixup function
+ The Sequoia NAND booting target now uses the recently extracted
+ cpu/ppc4xx/denali_data_eye.c file too.
- Add the function fdt_fixup_memory() to fixup the /memory node of the fdt
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+commit 0ddd969aec532bd7eae30fc09590488a3aaa629a
+Author: Lawrence R. Johnson <lrj@acm.org>
+Date: Thu Jan 3 15:02:02 2008 -0500
-commit 9c9109e7fcf7ac2ca19c95b8ac54b8d1c773b157
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Mon Nov 26 11:19:12 2007 -0600
+ ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Korat board
- Conditionally compile fdt_support.c
+ Signed-off-by: Larry Johnson <lrj@acm.org>
- Modify common/Makefile to conditionally compile fdt_support.c based
- on CONFIG_OF_LIBFDT.
+commit b05e8bf58be9d8956fdfde3d8c8e87c140414663
+Author: Lawrence R. Johnson <lrj@acm.org>
+Date: Fri Jan 4 02:11:56 2008 -0500
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Sequoia board
-commit d88e7ba0980773479e1a64badb293116071b7ef0
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Mon Nov 26 10:41:40 2007 -0600
+ Note: this patch changes the configuration of some GPIO registers:
- Fix build breakage due to libfdt import
+ Register Old Value New Value
+ --------------- ---------- ----------
+ DCR GPIO0_TCR 0x0000000F 0x0000F0CF
+ DCR GPIO0_TSRH 0x55005000 0x00000000
+ DCR GPIO1_TCR 0xC2000000 0xE2000000
+ DCR GPIO1_TSRL 0x0C000000 0x00200000
+ DCR GPIO1_ISR2L 0x00050000 0x00110000
- The IDS8247 got lost in the update and need an API update
- do to rename of functions in libfdt.
+ Signed-off-by: Larry Johnson <lrj@acm.org>
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+commit 5ab884b254ca2e707ab50545cd705f30108cf491
+Author: Lawrence R. Johnson <lrj@acm.org>
+Date: Thu Jan 3 18:54:00 2008 -0500
+
+ ppc4xx: Add functionality to GPIO support
+
+ This patch makes two additions to GPIO support:
+
+ First, it adds function gpio_read_in_bit() to read the a bit from the
+ GPIO Input Register (GPIOx_IR) in the same way that function
+ gpio_read_out_bit() reads a bit from the GPIO Output Register
+ (GPIOx_OR).
+
+ Second, it modifies function gpio_set_chip_configuration() to provide
+ an additional option for configuring the GPIO from the
+ "CFG_4xx_GPIO_TABLE".
+
+ According to the 440EPx User's Manual, when an alternate output is used,
+ the three-state control is configured in one of two ways, depending on
+ the particular output. The first option is to select the corresponding
+ alternate three-state control in the GPIOx_TRSH/L registers. The second
+ option is to select the GPIO Three-State Control Register (GPIOx_TCR) in
+ the GPIOx_TRSH/L registers, and set the corresponding bit in the
+ GPIOx_TCR register to enable the output. For example, the Manual
+ specifies configuring the GPIO00 Alternate 1 Signal (PreAddr07) to use
+ the alternate three-state control (first option), and specifies
+ configuring the GPIO32 Alternate 1 Signal (USB2OM0) with the output
+ enabled in the GPIOx_TCR register (second option).
+
+ Currently, gpio_set_chip_configuration() configures all alternate signal
+ outputs to use the first option. This patch allow the second option to
+ be selected by setting the "out_val" element in the table entry to
+ "GPIO_OUT_1". The first option is used when the "out_val" element is
+ set to "GPIO_OUT_0". Because "out_val" is not currently used when an
+ alternate signal is selected, and because all current GPIO tables set
+ "out_val" to "GPIO_OUT_0" for all alternate signals, this patch should
+ not change any existing configurations.
-commit 28f384b171bbf1fb2dafb1046e6d259a6b2f8714
-Author: Gerald Van Baren <vanbaren@cideas.com>
-Date: Fri Nov 23 19:43:20 2007 -0500
+ Signed-off-by: Larry Johnson <lrj@acm.org>
- Add spaces around the = in the fdt print format.
+commit 196404cdc1de495d6182e84731c200fc5748df15
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sun Dec 30 01:01:54 2007 -0500
- Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
+ PPC4xx: Remove sdram.h from board/lwmon5
-commit 29592ecba3b932b9b152bcec6c0c0806412db4a3
-Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-Date: Fri Dec 7 01:25:38 2007 +0900
+ These definitions are now in "include/ppc440.h".
- sh: Moved driver of the SuperH dependence
+ Signed-off-by: Larry Johnson <lrj@acm.org>
- The composition of the directory in the drivers/ changed.
- I moved SuperH serial driver and marubun PCMCIA driver.
+commit ef16fccf96e55eab93fe25d03ebe2e9b56e5332b
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sun Dec 30 01:01:32 2007 -0500
- Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ PPC4xx: Use common code for LWMON5 board SDRAM support
-commit 41be969f4957115ed7b1fe8b890bfaee99d7a7a2
-Author: Wolfgang Denk <wd@denx.de>
-Date: Thu Dec 6 10:21:19 2007 +0100
+ This patch also modifies the functionality of the code so that the data-eye
+ search is now done with with the cache disabled.
- Release v1.3.1
+ Signed-off-by: Larry Johnson <lrj@acm.org>
- Signed-off-by: Wolfgang Denk <wd@denx.de>
+commit 62cc3951ab72135d9c101f1845b794e63a0fa189
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sun Dec 30 01:01:14 2007 -0500
-commit cf5933ba1e97a1cd8f5f24070e820f21d976eaeb
-Author: Wolfgang Denk <wd@denx.de>
-Date: Thu Dec 6 10:21:03 2007 +0100
+ PPC4xx: Remove sdram.h from board/amcc/sequoia
- ADS5121 Board: fix compile problem.
+ These definitions are now in "include/ppc440.h".
- Signed-off-by: Wolfgang Denk <wd@denx.de>
+ Signed-off-by: Larry Johnson <lrj@acm.org>
-commit 8d4f040a3c15036a6ea25a9c39e7d89fefa8440d
-Author: Wolfgang Denk <wd@denx.de>
-Date: Mon Dec 3 00:15:28 2007 +0100
+commit ce3902e1765bbfb07cf5bbe98be9a68e3009996a
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sun Dec 30 01:00:50 2007 -0500
- Prepare for 1.3.1-rc1
+ PPC4xx: Use common code for Sequoia board SDRAM support
- Signed-off-by: Wolfgang Denk <wd@denx.de>
+ Signed-off-by: Larry Johnson <lrj@acm.org>
-commit 260eea5676ca46903a335686cc020b29c4ca46fe
-Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-Date: Thu Nov 29 01:21:54 2007 +0900
+commit 8b0c5c127690335758100c25eaec2b84db97c101
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Thu Dec 27 16:58:41 2007 +0100
- sh: Add SuperH boards maintainer to MAINTAINERS file
+ net: Add CONFIG_NET_DO_NOT_TRY_ANOTHER option
- Add MS7750SE and MS7722SE's board maintainer to MAINTAINERS file.
+ When CONFIG_NET_DO_NOT_TRY_ANOTHER is defined U-Boot's
+ networking stack does not automatically switch to
+ another interface. This patch does not touch the default
+ behavior.
- Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+ Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
-commit aa9c4f1d22701a92347c1c81f34d12c8ad3a3747
-Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-Date: Thu Nov 29 00:13:04 2007 +0900
+commit 505be87a65e4f87ad7d8da1d57ea4dcd487d7e32
+Author: Upakul Barkakaty <upakul@gmail.com>
+Date: Thu Nov 29 12:16:13 2007 +0530
- sh: Add ms7750se support in MAKEALL
+ NET: Proper return code handling in eth_init() function in file eth.c
- Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ This patch modifies the return code handling in the eth_init()
+ function, to be compatible with the handling of the return codes in
+ the other network stack files. It now returns a 0 on Success and -1 on
+ error.
-commit c7144373427a178332bf9754131c8c34c52c200a
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Tue Nov 27 09:44:53 2007 +0100
+ Signed-off-by: Upakul Barkakaty <upakul.barkakaty@conexant.com>
+ Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
- sh: Add sh3 and sh4 support in MAKEALL
+commit 5ca2d0953e4579a80810966cca2077e20d912c97
+Author: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
+Date: Mon Nov 19 20:27:04 2007 +0900
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
- Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ net/eth.c: Fix env_enetaddr signed overflow
-commit 130080874a3d28450098481a262c5f7c855e908d
-Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-Date: Sun Nov 25 02:51:17 2007 +0900
+ Assigning the output of simple_strtoul(CB:A9:87:65:43:21) to `char', we are
+ warned as below:
- sh: Add document for SuperH.
+ U-Boot 1.2.0 (Aug 30 2007 - 08:27:37)
- This document is a summary of information concerning SuperH of U-Boot.
+ DRAM: 256 MB
+ Flash: 32 MB
+ In: serial
+ Out: serial
+ Err: serial
+ Net: NEC-Candy
+ Warning: NEC-Candy MAC addresses don't match:
+ Address in SROM is 00:00:4C:80:92:A2
+ Address in environment is FFFFFFCB:FFFFFFA9:FFFFFF87:65:43:21
- Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ This patch changes env_enetaddr type from `char' to `unsigned char'.
-commit 33ecdc2f9d64926e1a6067b28f3a0aefc3b6d23d
-Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-Date: Sun Nov 25 02:39:31 2007 +0900
+ Cc: Masaki Ishikawa <ishikawa-masaki@cnt.mxe.nes.nec.co.jp>
+ Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
+ Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
- sh: Add marubun's pcmcia driver
+commit f85b60710571b37293d2233933b76e2aa3db5635
+Author: Rafal Jaworowski <raj@semihalf.com>
+Date: Thu Dec 27 18:19:02 2007 +0100
- Marubun pcmcia is a chip for PCMCIA used with SuperH.
- Of course, this can be used even by other architectures.
- When use this driver, came to be able to use CompactFlash
- and Ethernet.
+ Introduce new eth_receive routine
- Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ The purpose of this routine is receiving a single network frame, outside of
+ U-Boot's NetLoop(). Exporting it to standalone programs that run on top of
+ U-Boot will let them utilise networking facilities. For sending a raw frame
+ the already existing eth_send() can be used.
-commit febd86b969b975289ed948f1ac0eb9722da41ced
-Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-Date: Sun Nov 25 02:32:13 2007 +0900
+ The direct consumer of this routine is the newly introduced API layer for
+ external applications (enabled with CONFIG_API).
- sh: Update SuperH SCIF driver
+ Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
+ Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
+ Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
- - Changed volatile unsigned to vu_.
- - Changed Makefile for kconfig.
+commit 5c740711f0ea5b51414b341b71597c4a0751be74
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Thu Jan 3 10:41:04 2008 -0600
- Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ 8610: Move include of config.h earlier.
-commit a5f601fd1b1278deae5aa9fc27a232b0d1c1c788
-Author: Wolfgang Denk <wd@denx.de>
-Date: Mon Nov 26 19:18:21 2007 +0100
+ Include config.h earlier in the set of #includes
+ so as to avoid a incidental and duplicate definition
+ of CFG_CACHELINE_SIZE.
- Cleanup coding style; update CHANGELOG
+ Signed-off-by: Jon Loeliger
- Signed-off-by: Wolfgang Denk <wd@denx.de>
+commit 61d3421bdea090bd0399b14c3e10a3bebcc8d5ff
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Tue Dec 4 10:53:34 2007 -0600
-commit 3deca9d44767efd1b83f4b701f0dbf21a7595f7b
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sun Nov 25 22:39:25 2007 +0100
+ Don't slam #undef DEBUG in the 8641HPCN config file.
- MAKEALL: add missing 512x boards in ppc
+ Doing so prevents it from being individually set
+ and useful in other files.
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
-commit a340c325e668ca7386c2276387681720be9c3757
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sun Nov 25 18:45:47 2007 +0100
+commit ea9f7395ec362584e5e4f266bd0b0c4422cf6a4c
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Wed Nov 28 14:47:18 2007 -0600
- Makefile : fix tags ctags etags with new drivers organization
+ Convert MPC8641HPCN to use libfdt.
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ Assumes the presence of the aliases node in the DTS to
+ locate the ethernet, pci and serial nodes for fixups.
-commit 87ddedd6ad804427ce125ceaa076d7a4f74e9d5d
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sun Nov 25 18:45:47 2007 +0100
+ Use consistent fdtaddr and fdtfile in environment variables.
- Makefile : fix tags ctags etags with new drivers organization
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+commit ce37422d0002e10490e268392e0c4e3028e52cec
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Jan 2 14:06:26 2008 +0100
-commit 59829cc189378c142c13d2aa8d9a897d8bef3961
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sat Nov 24 21:26:56 2007 +0100
+ cfi_flash: Fix bug in flash_isset() to use correct 32bit function
- drivers/mtd : move mtd drivers to drivers/mtd
+ This bug was detected on the LWMON5 target which has 2 Intel 16bit wide
+ flash chips connected to a 32bit wide port.
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
-commit 318c0b90431f2648552e5ade78833f42652ce859
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sat Nov 24 21:17:55 2007 +0100
+commit 1182e9f8e3b92fc372d64943293de53daa2e26cf
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed Jan 2 15:58:44 2008 +0100
- drivers/misc : move misc drivers to drivers/misc
+ Fix compile problem introduced by "cleanup" commit 3dfd708c
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
-commit 33daf5b7858807cb4ce4158c2c56524671c14c08
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sat Nov 24 21:13:59 2007 +0100
+commit 1aaab9bfae0b3b2ee2b418c22c651280ee7b65c7
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed Jan 2 15:54:45 2008 +0100
- drivers/block : move block drivers to drivers/block
+ Make scripts and Makefiles POSIX compliant
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ The bash builtin versions of the "test" (resp. "[") command allow
+ using "==" for string comparisons, but POSIX compatible implemen-
+ tations (like /usr/bin/test) insist on using "=" only. On such systems
+ you will see:
-commit 0c698dcaa70275eb8814f665b545547cee013892
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sat Nov 24 20:59:50 2007 +0100
+ $ /usr/bin/test a == a && echo OK
+ /usr/bin/test: ==: binary operator expected
- drivers/rtc : move rtc drivers to drivers/rtc
+ This patch fixes Makefiles and scripts to use POSIX style.
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
-commit f868cc5a50757d94f36c312395481cb0f187d9e6
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sat Nov 24 20:14:44 2007 +0100
+commit 3dfd708cc1b2a966ad454ca9ed125dd17dbadbcc
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed Jan 2 12:38:43 2008 +0100
- drivers/hwmon : move hardware monitor drviers to drivers/hwmon
+ Minor coding style cleanup.
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
-commit 16b195c82a18cbfd164800f17a1ef9db2e48331a
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sat Nov 24 19:46:45 2007 +0100
+commit e174ac34adf5d5653df12bc3cf19c52063a71269
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Dec 28 17:29:56 2007 +0100
- drivers/input : move input drivers to drivers/input
+ ppc4xx: Coding style cleanup
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
-commit e4558666293364fc3af1c1d9381ca933fa0f1275
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sat Nov 24 19:40:11 2007 +0100
+commit 8ba132cab18ae438b6dd5b0214c28a8fc0d976e5
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Fri Dec 28 17:07:24 2007 +0100
- drivers/usb : move usb drivers to drivers/usb
+ ppc4xx: Complete PMC440 board support
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ This patch brings the PMC440 board configuration file.
+ Finally it enables the PMC440 board support.
-commit 1378df792a7ff3abd1bf54a63f5475784f5b083c
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sat Nov 24 19:33:38 2007 +0100
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
- drivers/serial : move serial drivers to drivers/serial
+commit 407843a582560fc5231299561ab3c2b6b6cd3397
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Fri Dec 28 17:07:18 2007 +0100
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ ppc4xx: Add FPGA support and BSP commands for PMC440 boards
-commit 2439e4bfa111babf4bc07ba20efbf3e36036813e
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Wed Nov 21 21:19:24 2007 +0100
+ This patch adds some BSP commands and FPGA booting support
+ for esd's PMC440 boards.
- drivers/net : move net drivers to drivers/net
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+commit 72c5d52aedcce35e4b4fa5895605554825b6a76f
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Fri Dec 28 17:07:14 2007 +0100
-commit 352d259130b349fe9593b8dada641bd78a9659e5
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Tue Nov 20 20:41:48 2007 +0100
+ ppc4xx: Add initial esd PMC440 board files
- drivers/video : move video drivers to drivers/video
+ This patch adds the first files for the new esd PMC440 boards.
+ The next two patches will complete the PMC440 board support.
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
-commit 73646217186aa17afc8e305c5f06f06dd335eaad
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Tue Nov 20 20:33:09 2007 +0100
+commit f6e0f1f61896ce7729ba1bcea2ffbd138d3947f5
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Fri Dec 28 17:10:36 2007 +0100
- drivers/pcmcia : move pcmcia drivers to drivers/pcmcia
+ ppc4xx: Add EEPROM write protection for PLU405 boards + misc. updates
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ - add EEPROM write protection for esd PLU405 boards.
+ - initialize NAND GPIOs
+ - use correct io accessors
+ - cleanup
-commit 93a686ee9c5ddc6fa368c32cfbfde6f6724599fc
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Tue Nov 20 20:28:09 2007 +0100
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
- drivers/pci : move pci drivers to drivers/pci
+commit 77660c4b59055d621d2a8595bd4c18bb277268fc
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Fri Dec 28 17:10:44 2007 +0100
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ ppc4xx: use correct io accessors for esd's LCD code
-commit 9162352817579840d7802da6d85872b3ca003c97
-Author: Gerald Van Baren <vanbaren@cideas.com>
-Date: Thu Nov 22 17:23:23 2007 -0500
+ This patch fixes esd's LCD dectection code to work correctly with
+ newer gcc versions.
- Fix fdt printing for updated libfdt
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
- Also improve printing (adopt dtc v1 "c style" hex format), whitespace cleanup.
+commit b56bd0fcfc1c73db722e3462c8a9bf607ba7775e
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Fri Dec 28 17:10:42 2007 +0100
- Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
+ ppc4xx: Maintenance patch for VOH405 boards
-commit 9eb77cea1fa12d5969eb26a1d1d81da381bd6b1c
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Wed Nov 21 13:30:15 2007 -0600
+ - add EEPROM write protection
+ - initialize NAND GPIOs
+ - use correct io accessors
+ - slow down I2C clock to 100kHz
+ - enable ext. I2C bus
+ - cleanup
- Add additional fdt fixup helper functions
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
- Added the following fdt fixup helpers:
- * do_fixup_by_prop{_u32} - Find matching nodes by property name/value
- * do_fixup_by_compat{_u32} - Find matching nodes by compat
+commit c05569066dbcba3fdf36d4d1943df265dc316a86
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Dec 28 16:08:08 2007 +0100
- The _u32 variants work the same only the property they are setting
- is know to be a 32-bit integer instead of a byte buffer.
+ ppc4xx: Enable 405EP PCI arbiter per default on all boards
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ In an attmemt to clean up the 4xx start.S file, I removed the enabling
+ of the internal 405EP PCI arbiter. This is needed for multiple other
+ 405EP platforms, like most of the esd 405EP. Now the internal PCI
+ arbiter is enabled again per default as it has been before.
-commit ab544633abdd14f4dd5d92e500b73eb59ef57e67
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Wed Nov 21 11:11:03 2007 -0600
+ Signed-off-by: Stefan Roese <sr@denx.de>
+ Acked-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
- Add fdt_fixup_ethernet helper to set mac addresses
+commit bec9264616fb78273a1d93e87ff4b0b67c7bec1b
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Dec 28 15:53:46 2007 +0100
- Added a fixup helper that uses aliases to set mac addresses
- in the device tree based on the bd_t
+ ppc4xx: Fix bug in cpu_init.c (405EP instead of 450EP)
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+ Acked-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
-commit dbaf07ce620aab249e3502b20a986234a6af1d3a
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Wed Nov 21 14:07:46 2007 -0600
+commit fb83a65c60ab5ca12358b75f1257e5eee6cdbf79
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Dec 28 06:06:04 2007 +0100
- Fix warnings from import of libfdt
+ ppc4xx: Fix compilation problem of kilauea/haleakala nand booting target
- cmd_fdt.c: In function fdt_print:
- cmd_fdt.c:586: warning: assignment discards qualifiers from pointer target type
- cmd_fdt.c:613: warning: assignment discards qualifiers from pointer target type
- cmd_fdt.c:635: warning: assignment discards qualifiers from pointer target type
- cmd_fdt.c:636: warning: assignment discards qualifiers from pointer target type
+ Use correct link to nand_ecc now located in drivers/mtd/nand/ for the
+ platforms mentioned above.
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ Signed-off-by: Stefan Roese <sr@denx.de>
-commit 8d04f02f6224e6983f4812ea4da704950ec8539c
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Wed Oct 24 11:04:22 2007 -0500
+commit b568fd25574181a3b12ae3d66b2913903442cb83
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Thu Dec 27 17:03:46 2007 +0100
- Update libfdt from device tree compiler (dtc)
+ Remove CPCI440 board
- Update libfdt to commit 8eaf5e358366017aa2e846c5038d1aa19958314e from
- the device tree compiler (dtc) project.
+ This board never left prototyping state and it
+ became a millstone round my neck. So remove it.
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
-commit e93becf80d732b64aef81b23e8b6ece02c40533d
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Sat Nov 3 19:46:28 2007 -0500
+commit c591dffe0cbacd896ccbad06011fe6d6afa080da
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Thu Dec 27 11:28:51 2007 -0500
- Move do_fixup* for libfdt into common code
+ Add support for Korat PPC440EPx board
- Moved the generic fixup handling code out of cpu/mpc5xxx and cpu/mpc8260
- into common/fdt_support.c and renamed:
+ These patches add support for the PPC440EPx-based "Korat" board to
+ U-Boot. They are based primarily on support for the Sequoia board.
- do_fixup() -> do_fixup_by_path()
- do_fixup_u32() -> do_fixup_by_path_u32()
+ Signed-off-by: Larry Johnson <lrj@acm.org>
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+commit 87dc096829e6a6363f4fdd73653b0093a85adbe0
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sat Dec 22 15:16:25 2007 -0500
-commit f738b4a75998f42a7408defadc9baac7a31c92db
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Thu Oct 25 16:15:07 2007 -0500
+ Add configuration file for Korat board
- Make no options to fdt print default to '/'
+ This patch supplies the configuration file for the Korat PPC440EPx-
+ processor board.
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ Signed-off-by: Larry Johnson <lrj@acm.org>
-commit a3c2933e02503fe36ade2c1b65af46f2b7a168e7
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Wed Oct 24 10:21:57 2007 -0500
+commit 8eb52d5d982b764b39c88d9d1064d56c5397bfa5
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sat Dec 22 15:16:11 2007 -0500
- Removed some nonused fdt functions and moved fdt_find_and_setprop out of libfdt
+ Add denali_data_eye.o and denali_spd_ddr2.o to PPC4xx Makefile
- Removed:
- fdt_node_is_compatible
- fdt_find_node_by_type
- fdt_find_compatible_node
+ Signed-off-by: Larry Johnson <lrj@acm.org>
- To ease merge of newer libfdt as we aren't using them anywhere at this time.
+commit aba19604d848b2838cfb9ebe818909e6a216058e
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Thu Dec 27 10:54:48 2007 -0500
- Also moved fdt_find_and_setprop out of libfdt into fdt_support.c for the same
- reason.
+ Add 440EPx DDR2 SPD DIMM support
- Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+ This patch adds SPD DDR2 support for the 440EPx ("Denali") SDRAM
+ controller. It should also work on the 440GRx. It is based on the DDR2
+ SPD code for the 440EP/440EPx, but makes no provision for DDR1 support.
-commit 98e2867cc85409b919f862e6c16026461ec955df
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Wed Nov 21 09:19:37 2007 -0700
+ This code has been tested on prototype Korat boards with three Kingston
+ DIMMS: 512 MiB ECC (one rank), 512 MiB non-ECC (one rank) and 1 GiB ECC
+ (two ranks). The Korat board has a single DIMM socket, but support has
+ been provided (though not tested) for boards with two DIMM sockets.
- [BUILD] Remove libraries when updating autoconf.mk
+ Signed-off-by: Larry Johnson <lrj@acm.org>
- Fix library problems caused by conditional compilation. Using
- autoconf.mk to decide which files to compile has caused a problem when
- changing configuration from one board to another without clearing out
- the library (*.a) files.
+commit 8a24a6963002cb867d5a6b70e3560f0b1467f55f
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sat Dec 22 15:15:30 2007 -0500
- It used to be that the linker was always passed the same list of .o
- files when building the .a files. However, that is not longer true
- with conditional compilation. Now, a different board config will have
- a different file list passed to the linker. The problem occurs when
- a library has already been built and the board config is changed.
+ Copy 440EPx/GRx SDRAM data-eye search to common directory
- Since the linker will update instead of replace a preexisting library,
- then if the file list changes to remove some object files the old
- objects will still exist in the library.
+ This patch creates a non-board-specific file for performing the SDRAM
+ data-eye search. It also adds ECC error checking to the test of valid
+ data on readback when ECC is enabled.
- The solution is to remove all old library files when autoconf.mk is
- made.
+ Signed-off-by: Larry Johnson <lrj@acm.org>
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+commit c46f53333b22b1f9098676bea8884fc7db820cf3
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sat Dec 22 15:15:13 2007 -0500
-commit ed1353d74b9ce8a7fcd660570b848a184d614b5f
-Author: Kumar Gala <galak@kernel.crashing.org>
-Date: Wed Nov 21 08:49:50 2007 -0600
+ Add definitions for 440EPx/GRx SDRAM controller to ppc440.h
- [BUILD] conditionally compile libfdt/*.c in libfdt/Makefile
+ This patch adds the Denali SDRAM controller definitions to "ppc440.h".
+ It also fixes two typos in the definitions, so the board-specific
+ "sdram.h" files containing these definitions are also fixed to avoid
+ compiler warnings.
- Modify libfdt/Makefile to conditionally compile the *.c files based
- on the board config.
+ Signed-off-by: Larry Johnson <lrj@acm.org>
+
+commit c348578bf612d0c56d8d376d23cae16defbd86af
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Thu Dec 27 10:50:55 2007 -0500
+
+ Add Ethernet 1000BASE-X support for PPC4xx
+
+ This patch adds a new switch: "CONFIG_PHY_DYNAMIC_ANEG". When this symbol
+ is defined, the PHY will advertise it's capabilities for autonegotiation
+ based on the capabilities shown in the PHY's status registers, including
+ 1000BASE-X. When "CONFIG_PHY_DYNAMIC_ANEG" is not defined, the PHY will
+ advertise hard-coded capabilities, as before.
+
+ Signed-off-by: Larry Johnson <lrj@acm.org>
+
+commit 9e2c347151db5ae8acf5f18b99493cd53e6637e3
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Thu Dec 27 09:52:17 2007 -0500
+
+ Add driver for National Semiconductor LM73 temperature sensor
+
+ This driver is based on the driver for the LM75.
+
+ Signed-off-by: Larry Johnson <lrj@acm.org>
+
+commit 12618278688ea9b3d76536960a5ad2e3790fac40
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sat Dec 22 15:14:00 2007 -0500
+
+ Add driver for STMicroelectronics M41T60 RTC
+
+ This driver is based on the driver for the M41T11. In the intended
+ application, the RTC will be powered by a large capacitor, rather than a
+ battery. The driver therefore checks to see whether the RTC has lost
+ power. The chip's OUT bit is normally reset from its power-up state. If
+ the OUT bit is read as set, or if the date and time are not valid, then the
+ RTC is assumed to have lost power, and its date and time are reset to
+ 1900-01-01 00:00:00.
+
+ Support for adjusting the speed of the clock to improve accuracy is
+ provided through an environment variable.
+
+ Signed-off-by: Larry Johnson <lrj@acm.org>
+
+commit d3471173e14b7544bb60339eda8d3d3906694b0a
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sat Dec 22 15:34:39 2007 -0500
+
+ Use out_be32() and friends to access memory-mapped registers in sequoia.c
+
+ Signed-off-by: Larry Johnson <lrj@acm.org>
+
+commit c68f59fe3ec16769f82b5fca7421983c336d3aac
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sat Dec 22 15:34:20 2007 -0500
+
+ Use definitions from "asm-ppc/mmu.h" in init.S for Sequoia
+
+ Signed-off-by: Larry Johnson <lrj@acm.org>
+
+commit 0d9cdeac1d3fa8d62ed7d883acc950c364f5bda8
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sat Dec 22 15:23:50 2007 -0500
+
+ Cosmetic changes to ECC POST for AMCC Denali core
+
+ Signed-off-by: Larry Johnson <lrj@acm.org>
+
+commit 2e583d6c81034f80a267b89fa55498ae063ccef1
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Dec 26 20:20:19 2007 +0100
+
+ ppc4xx: Fix compilation problem in 405 cache POST test
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 42d55ea0bde06e47d5a3b49b0d91002acd8e5708
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Dec 22 12:20:09 2007 +0100
+
+ ppc4xx: Move virtual address of POST cache test to bigger address
+
+ On Sequoia & LWMON5 the virtual address of the POST cache test is now
+ moved to a bigger address. This enables usage of more memory on those
+ boards.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit d91722102cf63f77a0148ed3f3d54a26d87575e9
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Dec 22 12:18:26 2007 +0100
+
+ ppc4xx: Fix problem in 44x cache POST routine
+
+ As repoted by Larry Johnson, running "diag run cache" caused a crash
+ in U-Boot. This problem was introduced by a patch that removed the
+ TLB entry for the cache test after the test has completed. Since this
+ TLB was only setup once, a 2nd attempt to run this cache test
+ failed with a crash. Now this TLB entry is created every time the
+ routine is called.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit b0265b576bb8fa9465f99e99c323768b562fadc2
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Dec 21 07:51:29 2007 +0100
+
+ ppc4xx: Update Makalu fdt support
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit bf8324e4a50758daff8cddd04c6a2ff8ed775bea
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Dec 19 09:05:40 2007 +0100
+
+ ppc4xx: Add fdt support to AMCC Katmai eval board
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 328a340392a5df9aaf00792be989df73e750859e
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Dec 18 08:44:51 2007 +0100
+
+ ppc4xx: fdt: Cleanup setup of cpu node setup
+
+ Now the cpu node setup ("timebase-frequency" and "clock-frequency") is
+ without using the absolute path to the cpu node. This makes it possible
+ to use this U-Boot version with both versions of cpu-node naming
+ "cpu@0" and the former "PowerPC,440EPx@0".
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 7812bc4a2e2436ebbc0ce5b4e99c1dfc2e77eb5b
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Dec 17 17:26:21 2007 +0100
+
+ ppc4xx: Fix lwmon5 compilation problem
+
+ Now that the 440EPx ECC test is not board specific anymore
+ remove this Makefile.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 42ed33ffe135f618680f9d6e9712eb35a85bcb62
+Author: Anatolij Gustschin <agustschin@t-online.de>
+Date: Wed Dec 5 17:43:20 2007 +0100
+
+ Fix ppc4xx clear_bss() code
+
+ ppc4xx clear_bss() fails if BSS segment size is not
+ divisible by 4 without remainder. This patch provides
+ fix for this problem.
+
+ Signed-off-by: Anatolij Gustschin <agust@denx.de>
+
+commit 85dc2a7f82d11e17f0ca2a448118aed7f7a4b85d
+Author: Niklaus Giger <niklausgiger@gmx.ch>
+Date: Fri Nov 30 18:35:11 2007 +0100
+
+ PPC4xx: Minimal changes to add vxWorks support
+
+ Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
+
+commit 052440b022ca8981d39b6f8c10d1aa6326f47480
+Author: Markus Klotzbücher <mk@denx.de>
+Date: Fri Nov 23 13:09:18 2007 +0100
+
+ ppc4xx: Add CONFIG_BOOTP_SUBNETMASK to Sequoia board config
+
+ When using dhcp/bootp the "netmask" environment variable is not
+ set because CONFIG_BOOTP_SUBNETMASK is not defined. But usually this is
+ desireable, so the following patch adds this this option to the board
+ config.
+
+ Signed-off-by: Markus Klotzbuecher <mk@denx.de>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit a724a9b40c7fbeb6ade193ca52321b441eaecb4e
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sat Oct 27 12:48:15 2007 -0400
+
+ Fix/enhance ECC POST for 440EPx/GRx
+
+ This patch allows the ECC POST to be used for different boards with the
+ PPC440 Denali SDRAM controller. Modifications include skipping the test
+ if ECC is not enabled (as for non-ECC DIMMs) and adding synchronization
+ to prevent timing errors.
+
+ Signed-off-by: Larry Johnson <lrj@acm.org>
+
+commit 454a6cf8d498f70d2b3e18f07837603eb24b12d4
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Sat Oct 27 12:48:05 2007 -0400
+
+ PPC4xx: Move/rename ECC POST for 440EPx/GRx
+
+ Signed-off-by: Larry Johnson <lrj@acm.org>
+
+commit c29d2d3680046d430022c55e50fcb27f5866517e
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Fri Dec 14 11:20:33 2007 +0100
+
+ ppc4xx: use correct io accessors for 4xx ethernet POST
+
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+
+commit ba79fde58a48c0a6ff8e2a96caba951594142203
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Fri Dec 14 11:19:56 2007 +0100
+
+ ppc4xx: fix flush + invalidate_dcache_range arguments
+
+ flush + invalidate_dcache_range() expect the start and stop+1 address.
+ So the stop address is the first address behind (!) the range.
+
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+
+commit 871e6ce188a7c6bc7321bcf8372857035d20f1cd
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Dec 14 08:41:29 2007 +0100
+
+ ppc4xx: fdt: use fdt_fixup_ethernet()
+
+ By using aliases in the dts file, the ethernet node fixup is
+ much easier with the recently added functions.
+
+ Please note that the dts file needs the aliases for this to work.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 136288847e3b04f2ff357a067ad45e10afa0a24c
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Dec 13 14:52:53 2007 +0100
+
+ ppc4xx: Bring 4xx fdt support up-to-date
+
+ This patch update the 4xx fdt support. It enabled fdt booting
+ on the AMCC Kilauea and Sequoia for now. More can follow later
+ quite easily.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 0dc80e2759fba859ccc4cdadc633577ca2971f3e
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Dec 27 07:50:54 2007 +0100
+
+ cfi_flash: Add missing check for erased dest to flash_write_cfibuffer()
+
+ The check for an sufficiently erased destination was missing in the
+ buffered write function of the cfi flash driver (when
+ CFG_FLASH_USE_BUFFER_WRITE is defined). This patch adds this check to that
+ writing to such a region will fail with the currect error message.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 33ed73bc0e38d0f2b5c183d4629d8f207e5b9994
+Author: Martin Krause <martin.krause@tqs.de>
+Date: Mon Nov 12 10:56:17 2007 +0100
+
+ Some configuration updates for the TQM5200 based TB5200 board:
+
+ - enable command line history
+ - increase malloc space (because of bigger flash sectors)
+
+ Signed-off-by: Martin Krause <martin.krause@tqs.de>
+
+commit e318d9e9021a0af7508171f84ed09d0e79f0284e
+Author: Martin Krause <martin.krause@tqs.de>
+Date: Thu Sep 27 11:10:08 2007 +0200
+
+ TQM8xx: use the CFI flash driver on all TQM8xx boards
+
+ Signed-off-by: Martin Krause <martin.krause@tqs.de>
+
+commit 11d9eec479b470eab9242ab937fca70a876d9376
+Author: Martin Krause <martin.krause@tqs.de>
+Date: Wed Sep 26 17:55:56 2007 +0200
+
+ TQM885D: adjust for doubled flash sector size + some minor fixes
+
+ Signed-off-by: Martin Krause <martin.krause@tqs.de>
+
+commit 22d1a56cbfb0bff34f477b4db6a55d076d829b83
+Author: Jens Gehrlein <jens.gehrlein@tqs.de>
+Date: Wed Sep 26 17:55:54 2007 +0200
+
+ TQM885D: Exchanged SDRAM timing by a more relaxed timing.
+
+ CAS-Latency=2, Write Recovery Time tWR=2
+ The max. supported bus frequency is 66 MHz. Therefore, changed
+ threshold to switch from 1:1 mode to 2:1 from 80 MHz to 66 MHz.
+
+ Signed-off-by: Martin Krause <martin.krause@tqs.de>
+
+commit b988b8cd443989be65161888eea0127ad03f846f
+Author: Martin Krause <martin.krause@tqs.de>
+Date: Wed Sep 26 17:55:56 2007 +0200
+
+ TQM885D: use calculated cpuclk instead of measuring it
+
+ On the TQM885D the measurement of cpuclk with the PIT reference
+ timer ist not necessary. Since all module variants use the same
+ external 10 MHz oscillator, the cpuclk only depends on the PLL
+ configuration - which is readable by software.
+
+ Signed-off-by: Martin Krause <martin.krause@tqs.de>
+
+commit 492c7049869348d31168de8dad89651315e468e0
+Author: Jens Gehrlein <jens.gehrlein@tqs.de>
+Date: Thu Sep 27 14:54:46 2007 +0200
+
+ TQM885D: fix SDRAM refresh
+
+ At 133 MHz the current SDRAM refresh rate is too fast
+ (measured 4 * 1.17 us).
+ CFG_MAMR_PTA changes from 39 to 128. This result
+ in a refresh rate of 4 * 7.8 us at the default clock
+ 66 MHz. At 133 MHz the value will be then 4 * 3.8 us.
+ This is a compromise until a new method is found to
+ adjust the refresh rate.
+
+ Signed-off-by: Martin Krause <martin.krause@tqs.de>
+
+commit dabad4b9bc46908e301f73ce76b38b23626a96e9
+Author: Jens Gehrlein <jens.gehrlein@tqs.de>
+Date: Thu Sep 27 14:54:46 2007 +0200
+
+ TQM860M: Support for 10col SDRAMs, max. 128 MiB
+
+ Signed-off-by: Martin Krause <martin.krause@tqs.de>
+
+commit 61fb15c516fef5631e305f1976d7b3a679725856
+Author: Wolfgang Denk <wd@denx.de>
+Date: Thu Dec 27 01:52:50 2007 +0100
+
+ Fix coding style issues; update CHANGELOG.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 467bcee11fe26ad422f2de971aa70866079870f2
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Fri Dec 14 15:36:18 2007 +0100
+
+ cfi_flash: Add manufacturer-specific fixups
+
+ Run fixups based on the JEDEC manufacturer ID independent of the
+ command set ID.
+
+ This changes current behaviour: Previously, geometry reversal for AMD
+ chips were done based on the command set ID, while they are now done
+ based on the JEDEC manufacturer and device ID.
+
+ Also add fixup for top-boot Atmel chips. A fixup is needed for
+ AT49BV6416(T) too, but since u-boot currently only reads the low byte
+ of the device ID, there's no way to tell it apart from AT49BV642D,
+ which should not have this fixup. Since AT49BV642D support is
+ necessary to get ATNGW100 board support into mainline, I've commented
+ out the fixup for now.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 0ddf06ddf6b4bd057ad4c5f0dffea7870ba06a2a
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Fri Dec 14 15:36:17 2007 +0100
+
+ cfi_flash: Add cmdset-specific init functions
+
+ Move things like reading JEDEC IDs and fixing up geometry reversal
+ into separate functions. The geometry reversal fixup is now performed
+ by altering the qry structure directly, which makes the sector init
+ code slightly cleaner.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit e23741f4a6d8047520ef0d4971762749b3587d32
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Fri Dec 14 15:36:16 2007 +0100
+
+ cfi_flash: Read whole QRY structure in one go
+
+ Read out the whole CFI Standard Query structure after successful cfi
+ identification. This allows subsequent code to access this information
+ directly without having to go through flash_read_uchar() and friends.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit df9c25ea04b38a0e05d4f8c73c5cc144cdafa7db
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Mon Dec 17 11:02:44 2007 +0100
+
+ AVR32: Fix logic inversion in disable_interrupts()
+
+ disable_interrupts() should return nonzero if interrupts were
+ _enabled_ before, not disabled.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit acac475212cbedb17b321a363a1c878e2b47b37f
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Fri Dec 14 16:51:22 2007 +0100
+
+ AVR32: Enable interrupts at bootup
+
+ The timer code depends on the timer interrupt to keep track of the
+ upper 32 bits of the cycle counter. This obviously doesn't work when
+ interrupts are disabled the whole time.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 9570bcd87f4db255514f43b6701746c412f8fef0
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Thu Nov 15 10:03:45 2007 +0100
+
+ AVR32: Fix wrong pin setup for USART3
+
+ As reported by Gerhard Berghofer:
+
+ in "gpio_enable_usart3" the correct pins for USART 3 are PB17 and PB18
+ instead of PB18 and PB19.
+
+ which is obviously correct. There's currently no code that uses
+ USART3, but custom boards may run into problems.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 09ea0de03dcc3ee7af045b0b572227bda2c1c918
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Thu Nov 1 12:44:20 2007 +0100
+
+ README: Remove ATSTK1000 daughterboard list
+
+ As noted by Kim Phillips, these lists tend to become out of date.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit c81cbbad21cb0ae983e2e796211202234cdc8be2
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Tue Oct 30 14:56:36 2007 +0100
+
+ Add ATSTK100[234] to MAINTAINERS
+
+ Add all the ATSTK1000 daughterboards to MAINTAINERS along with their
+ "mother". Also update the entry for ATSTK1000 to be not only about the
+ AP7000 CPU; it's intended to handle all CPUs in the AT32AP family.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 64ff2357b1727213803591813dbc779c924bf772
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Mon Oct 29 13:02:54 2007 +0100
+
+ AVR32: Add support for the ATSTK1004 board
+
+ ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU,
+ which is a derivative of AT32AP7000.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 667568db157f374b85abd7e03596ddd1f0b25681
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Mon Oct 29 13:02:54 2007 +0100
+
+ AVR32: Add support for the ATSTK1003 board
+
+ ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU,
+ which is a derivative of AT32AP7000.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 5fee84a794a51ec830548cda485a770efb018b92
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Mon Oct 29 13:23:33 2007 +0100
+
+ AVR32: Make some AT32AP700x peripherals optional
+
+ Add a chip-features file providing definitions of the form
+
+ AT32AP700x_CHIP_HAS_<peripheral>
+
+ to indicate the availability of the given peripheral on the currently
+ selected chip.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 36f28f8a9605ee5dcfa330482cfc62171261af97
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Mon Oct 29 13:09:56 2007 +0100
+
+ AVR32: Rename at32ap7000 -> at32ap700x
+
+ The SoC-specific code for all the AT32AP700x CPUs is practically
+ identical; the only difference is that some chips have less features
+ than others. By doing this rename, we can add support for the AP7000
+ derivatives simply by making some features conditional.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 4d5fa99c73f354e7cf985efcf417ea55ca2f6a5e
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Fri Jun 29 18:22:34 2007 +0200
+
+ atmel_mci: Show SR when block read fails
+
+ Show controller status as well as card status when an error occurs
+ during block read.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 8697e6a19b10f514511b6a9c86de88bd108c4f8d
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Dec 13 14:52:53 2007 +0100
+
+ ppc4xx: Bring 4xx fdt support up-to-date
+
+ This patch update the 4xx fdt support. It enabled fdt booting
+ on the AMCC Kilauea and Sequoia for now. More can follow later
+ quite easily.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 12d30aa79779c2aa7a998bbae4c075f822a53004
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Thu Dec 13 12:56:34 2007 +0100
+
+ cfi_flash: Use map_physmem() and unmap_physmem()
+
+ Use map_physmem() and unmap_physmem() to convert from physical to
+ virtual addresses. This gives the arch a chance to provide an uncached
+ mapping for flash accesses.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 4d7d6936eb29af7cca330937808312aa5f61454d
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Thu Dec 13 12:56:33 2007 +0100
+
+ Introduce map_physmem() and unmap_physmem()
+
+ map_physmem() returns a virtual address which can be used to access a
+ given physical address without involving the cache. unmap_physmem()
+ should be called when the virtual address returned by map_physmem() is
+ no longer needed.
+
+ This patch adds a stub implementation which simply returns the
+ physical address cast to a uchar * for all architectures except AVR32,
+ which converts the physical address to an uncached virtual mapping.
+ unmap_physmem() is a no-op on all architectures, but if any
+ architecture needs to do such mappings through the TLB, this is the
+ hook where those TLB entries can be invalidated.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit cdbaefb5f5f03e54455d0439dcf6dbd97ead1f9d
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Thu Dec 13 12:56:32 2007 +0100
+
+ cfi_flash: Introduce read and write accessors
+
+ Introduce flash_read{8,16,32,64) and flash_write{8,16,32,64} and use
+ them to access the flash memory. This makes it clearer when the flash
+ is actually being accessed; merely dereferencing a volatile pointer
+ looks just like any other kind of access.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 812711ce6b3a386125dcf0d6a59588e461abbb87
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Thu Dec 13 12:56:31 2007 +0100
+
+ Implement __raw_{read,write}[bwl] on all architectures
+
+ This adds implementations of __raw_read[bwl] and __raw_write[bwl] to
+ m68k, ppc, nios and nios2. The m68k and ppc implementations were taken
+ from Linux.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit be60a9021c82fc5aecd5b2b1fc96f70a9c81bbcd
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sat Oct 6 18:55:36 2007 +0200
+
+ cfi_flash: Reorder functions and eliminate extra prototypes
+
+ Reorder the functions in cfi_flash.c so that each function only uses
+ functions that have been defined before it. This allows the static
+ prototype declarations near the top to be eliminated and might allow
+ gcc to do a better job inlining functions.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 3055793bcbdf24b1f8117f606ffb766d32eb766f
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Thu Dec 13 12:56:29 2007 +0100
+
+ cfi_flash: Make some needlessly global functions static
+
+ Make functions not declared in any header file static.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 7e5b9b471518c5652febc68ba62b432193d6abf4
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Thu Dec 13 12:56:28 2007 +0100
+
+ cfi_flash: Break long lines
+
+ This patch tries to keep all lines in the cfi_flash driver below 80
+ columns. There are a few lines left which don't fit this requirement
+ because I couldn't find any trivial way to break them (i.e. it would
+ take some restructuring, which I intend to do in a later patch.)
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 42026c9cb3a76849b41e6e24abfb7b56807a5c1a
+Author: Bartlomiej Sieka <tur@semihalf.com>
+Date: Tue Dec 11 13:59:57 2007 +0100
+
+ CFI: synchronize command offsets with Linux CFI driver
+
+ Fixes non-working CFI Flash on the Inka4x0 board.
+
+ Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
+
+commit 8ff3de61fc5f9b3b21647bce081a3b7f710f0d4d
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Fri Dec 7 12:17:34 2007 -0600
+
+ Handle MPC85xx PCIe reset errata (PCI-Ex 38)
+
+ On the MPC85xx boards that have PCIe enable the PCIe errata fix.
+ (MPC8544DS, MPC8548CDS, MPC8568MDS).
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 82ac8c97145a4c3bf8b3dbfad00fa96e920f9b9c
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Fri Dec 7 12:04:30 2007 -0600
+
+ Update Freescale MPC85xx ADS/CDS/MDS board config
+
+ * Enabled CONFIG_CMD_ELF
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit d435793229ce29a42797c1edc39f5b34f987f91a
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Fri Dec 7 04:59:26 2007 -0600
+
+ Handle Asynchronous DDR clock on 85xx
+
+ The MPC8572 introduces the concept of an asynchronous DDR clock with
+ regards to the platform clock.
+
+ Introduce get_ddr_freq() to report the DDR freq regardless of sync/async
+ mode.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 22abb2d2eaf7b795a6923c6273ec9cb53fda9a10
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Nov 29 10:34:28 2007 -0600
+
+ Update Freescale MPC85xx ADS/CDS/MDS board config
+
+ * Removed some misc environment setup
+ * Enabled CONFIG_CMDLINE_EDITING
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 415a613babb84d5e5d5b42e8e553868c71fc3a64
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Nov 29 10:47:44 2007 -0600
+
+ Move the MPC8541/MPC8555/MPC8548 CDS board under board/freescale.
+
+ Minor path corrections needed to ensure buildability.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit c2d943ffbfd3359b3b45d177b437379d2cb86fbf
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Nov 29 10:16:18 2007 -0600
+
+ Move the MPC8540 ADS board under board/freescale.
+
+ Minor path corrections needed to ensure buildability.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 870ceac5b3a3486c109396e005af81ae762b5710
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Nov 29 10:14:50 2007 -0600
+
+ Move the MPC8560 ADS board under board/freescale.
+
+ Minor path corrections needed to ensure buildability.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit acbca876fb3fec25cd9c55b0efc81ff618ff5262
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Nov 29 10:13:47 2007 -0600
+
+ Move the MPC8568 MDS board under board/freescale.
+
+ Minor path corrections needed to ensure buildability.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit a853d56c59b33415304531443633808736acfc6e
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Nov 29 02:18:59 2007 -0600
+
+ Use standard LAWAR_TRGT_IF_* defines for LAW setup on 85xx
+
+ We already had defines for LAWAR_TRGT_IF_* that we should use
+ rather than creating new ones. Also, added some missing defines for
+ PCIE targets.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 04db400892da37b76a585e332a0c137954ad2015
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Nov 29 02:10:09 2007 -0600
+
+ Stop using immap_t on 85xx
+
+ In the future the offsets to various blocks may not be in same location.
+ Move to using CFG_MPC85xx_*_ADDR as the base of the registers
+ instead of getting it via &immap.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 2714223f8e04ab3e4133ff65872eef366d90bfea
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Nov 29 01:23:09 2007 -0600
+
+ Remove CONFIG_OF_FLAT_TREE related code from mpc85xx since we now use libfdt
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit c480861bf000156e6a3e932c258db59ff2212dd3
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Nov 29 01:06:19 2007 -0600
+
+ Update MPC8568 MDS to use libfdt
+
+ Updated the MPC8568 MDS config to use libfdt and assume use of aliases for
+ ethernet, pci, and serial for the various fixups that are done.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 1563f56e0c68f6920f956382d6d13bee3f01c0f7
+Author: Haiying Wang <Haiying.Wang@freescale.com>
+Date: Wed Nov 14 15:52:06 2007 -0500
+
+ Add PCI Express support on MPC8568MDS
+
+ Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit b90d25497625b90ffa3f2911a0895ca237556ff5
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Nov 29 00:11:44 2007 -0600
+
+ Update MPC85xx CDS to use libfdt
+
+ Updated the MPC85xx CDS config to use libfdt and assume use of aliases for
+ ethernet, pci, and serial for the various fixups that are done.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 0fd5ec66b10521a057ad73e69ab5f0f9eafba255
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Wed Nov 28 22:54:27 2007 -0600
+
+ Update MPC8540 ADS to use libfdt
+
+ Updated the MPC8540 ADS config to use libfdt and assume use of aliases for
+ ethernet, pci, and serial for the various fixups that are done.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 5ce715802f6c50dc78b3405b92f184b1e3710519
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Wed Nov 28 22:40:31 2007 -0600
+
+ Update MPC8560 ADS to use libfdt
+
+ Updated the MPC8560 ADS config to use libfdt and assume use of aliases for
+ ethernet, pci, and serial for the various fixups that are done.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit aafeefbdb8b029f5ca2a195598d0a501a606eea9
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Wed Nov 28 00:36:33 2007 -0600
+
+ Stop using immap_t for cpm offset on 85xx
+
+ In the future the offsets to various blocks may not be in same location.
+ Move to using CFG_MPC85xx_CPM_ADDR as the base of the CPM registers
+ instead of getting it via &immap->im_cpm.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit f59b55a5b8fcadaa99781ba48e7a38e956afa527
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Tue Nov 27 23:25:02 2007 -0600
+
+ Stop using immap_t for guts offset on 85xx
+
+ In the future the offsets to various blocks may not be in same location.
+ Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers
+ instead of getting it via &immap->im_gur.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 50c03c8cf494d91cdec39670d95337c743e16ec9
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Tue Nov 27 22:42:34 2007 -0600
+
+ Update MPC8544 DS config
+
+ * Removed HAS_ETH2/HAS_ETH3 - MPC8544 only has TSEC1/2
+ * Removed some misc environment setup
+ * Moved to using fdtfile & fdtaddr as fdt env var names
+ * Enabled CONFIG_CMDLINE_EDITING
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit addce57e2e4c49e77ffb2020a84690713bb18b47
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Mon Nov 26 17:12:24 2007 -0600
+
+ Update MPC8544DS to use libfdt
+
+ Updated the MPC8544DS config to use libfdt and assume use of aliases for
+ ethernet, pci, and serial for the various fixups that are done.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit f852ce72f100cabd1f11c21c085a0ad8eca9fb65
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Nov 29 00:15:30 2007 -0600
+
+ Add libfdt based ft_cpu_setup for mpc85xx
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 3b9abdc448a1c2c6a4c2aa292724b4d1a05166a9
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Dec 11 13:38:19 2007 +0100
+
+ ppc4xx: Correct GPIO offset in gpio_config()
+
+ Thanks to Gary Jennejohn for pointing this out.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 8809a2713b1ceaf3da55d9d785470294f15de06a
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Dec 11 11:46:01 2007 +0100
+
+ rtc: Fix merging problem
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 7cfc12a7dcfdb350e2ab76db4dafcc30f7e77c2b
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Dec 8 14:47:34 2007 +0100
+
+ ppc4xx: 405EX: Correctly enable USB pins
+
+ This patch selects the USB data pins in the 405EX GPIO and MFC (multi
+ function control) registers. This is done for the AMCC Kilauea and
+ Makalu eval boards.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 9692c2734a47f23b44a0f68042a3e2ca8d1bfb39
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Dec 8 08:25:09 2007 +0100
+
+ CFI: Coding style cleanup
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 81b20ccc2d795ae9a1199db5a50ad9c28d1e4d22
+Author: Michael Schwingen <michael@schwingen.org>
+Date: Fri Dec 7 23:35:02 2007 +0100
+
+ CFI: support JEDEC flash roms in CFI-flash framework
+
+ The following patch adds support for non-CFI flash ROMS, by hooking into the
+ CFI flash code and using most of its code, as recently discussed here in the
+ thread "Mixing CFI and non-CFI flashs".
+
+ Signed-off-by: Michael Schwingen <michael@schwingen.org>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit c01b17dd856fa120b2970f50d9598546a4927ec3
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Wed Nov 28 21:24:50 2007 -0500
+
+ Conditionally compile fdt_fixup_ethernet()
+
+ Fix compiler warnings: On boards that don't have ethernets defined,
+ don't compile fdt_fixup_ethernet().
+
+commit 246d4ae6bc282bc1841224e1c5fc49dc925e0bf7
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Tue Nov 27 21:59:46 2007 -0600
+
+ Convert boards that set memory node to use fdt_fixup_memory()
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 151c8b09b35eebe8fd9139cb6c1d91c27b22f058
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Mon Nov 26 17:06:15 2007 -0600
+
+ Added fdt_fixup_stdout that uses aliases to set linux,stdout-path
+
+ We use a combination of the serialN alias and CONFIG_CONS_INDEX to
+ determine which serial alias we should set linux,stdout-path to.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 3c9272813fad84c691d0e4989bb18a3ffebdebfc
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Mon Nov 26 14:57:45 2007 -0600
+
+ Add common memory fixup function
+
+ Add the function fdt_fixup_memory() to fixup the /memory node of the fdt
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 9c9109e7fcf7ac2ca19c95b8ac54b8d1c773b157
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Mon Nov 26 11:19:12 2007 -0600
+
+ Conditionally compile fdt_support.c
+
+ Modify common/Makefile to conditionally compile fdt_support.c based
+ on CONFIG_OF_LIBFDT.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit d88e7ba0980773479e1a64badb293116071b7ef0
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Mon Nov 26 10:41:40 2007 -0600
+
+ Fix build breakage due to libfdt import
+
+ The IDS8247 got lost in the update and need an API update
+ do to rename of functions in libfdt.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 28f384b171bbf1fb2dafb1046e6d259a6b2f8714
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Fri Nov 23 19:43:20 2007 -0500
+
+ Add spaces around the = in the fdt print format.
+
+ Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
+
+commit 29592ecba3b932b9b152bcec6c0c0806412db4a3
+Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+Date: Fri Dec 7 01:25:38 2007 +0900
+
+ sh: Moved driver of the SuperH dependence
+
+ The composition of the directory in the drivers/ changed.
+ I moved SuperH serial driver and marubun PCMCIA driver.
+
+ Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+
+commit 41be969f4957115ed7b1fe8b890bfaee99d7a7a2
+Author: Wolfgang Denk <wd@denx.de>
+Date: Thu Dec 6 10:21:19 2007 +0100
+
+ Release v1.3.1
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit cf5933ba1e97a1cd8f5f24070e820f21d976eaeb
+Author: Wolfgang Denk <wd@denx.de>
+Date: Thu Dec 6 10:21:03 2007 +0100
+
+ ADS5121 Board: fix compile problem.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit a27044b14a9e93678a82d7b35f202b93e7687abc
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Dec 6 05:58:43 2007 +0100
+
+ ppc4xx: Enable hardware-fix for PCI/DMA errata on AMCC 440SP/SPe boards
+
+ This patch enables the hardware-fix for the PCI/DMA errata's 19+22 by
+ setting the FIXD bit in the SDR0_MFR register. Here a description of the
+ symptoms:
+
+ Problem Description
+ ------------------------------
+ If a DMA is performed between memory and PCI with the DMA 1 Controller
+ using prefetch, and as a result uses a special purpose buffer selected by
+ the PCIXn Bridge Options 1 Register (PCIXn_BRDGOPT1[RBP7] - bits 31-29),
+ the first part of the transfer sequence is performed twice. The
+ PPC440SPe PCI Controller requests more data than was needed such that in
+ the case of enforce memory protection, a host CPU exception can occur.
+ No data is corrupted, because data transfer is stopped in the PCI
+ Controller. Prefetch enable is specified by setting DMA Configuration
+ Register (I2O0_DMAx_CFG[DXEPD] - bit 31) to 0.
+
+ Behavior that may be observed in a running system
+ ---------------------------------------------------------------------------
+
+ 1. DMA performance is decreased because of the double access on the PCI bus
+ interface.
+ 2. If an illegal access to some address on the PCI bus is detected at the
+ system level, a machine check or similar system error may occur.
+
+ Workarounds Available
+ ----------------------------------
+
+ 1. Do not program prefetch. Note that a prefetch command cannot be programmed
+ without selecting a special purpose buffer.
+ 2. To avoid crossing a physical boundary of the PCI slave device, add 512
+ bytes of address to the PCI address range.
+
+ This patch was originally provided by Pravin M. Bathija <pbathija@amcc.com>
+ from AMCC and slighly changed.
+
+ Signed-off-by: Pravin M. Bathija <pbathija@amcc.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit a90921f71d225bf9e0f0fc7b8beadeb8001bf78a
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Dec 4 16:29:48 2007 +0100
+
+ ppc4xx: Yosemite/Yellowstone: Add DTT AD7414 support
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 8d4f040a3c15036a6ea25a9c39e7d89fefa8440d
+Author: Wolfgang Denk <wd@denx.de>
+Date: Mon Dec 3 00:15:28 2007 +0100
+
+ Prepare for 1.3.1-rc1
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit e15e33433e7c05111968dc9b434a52fd42cbd221
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Nov 30 07:15:41 2007 +0100
+
+ ppc4xx: Kilauea: Add PCIe reset assertion upon power-up
+
+ This manual PCIe reset triggering solves the problem seen with the
+ Intel EPRO/1000 card, which was not detected (link not established)
+ upon power-up reset.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 260eea5676ca46903a335686cc020b29c4ca46fe
+Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+Date: Thu Nov 29 01:21:54 2007 +0900
+
+ sh: Add SuperH boards maintainer to MAINTAINERS file
+
+ Add MS7750SE and MS7722SE's board maintainer to MAINTAINERS file.
+
+ Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+
+commit aa9c4f1d22701a92347c1c81f34d12c8ad3a3747
+Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+Date: Thu Nov 29 00:13:04 2007 +0900
+
+ sh: Add ms7750se support in MAKEALL
+
+ Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+
+commit c7144373427a178332bf9754131c8c34c52c200a
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Tue Nov 27 09:44:53 2007 +0100
+
+ sh: Add sh3 and sh4 support in MAKEALL
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+
+commit 130080874a3d28450098481a262c5f7c855e908d
+Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+Date: Sun Nov 25 02:51:17 2007 +0900
+
+ sh: Add document for SuperH.
+
+ This document is a summary of information concerning SuperH of U-Boot.
+
+ Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+
+commit 33ecdc2f9d64926e1a6067b28f3a0aefc3b6d23d
+Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+Date: Sun Nov 25 02:39:31 2007 +0900
+
+ sh: Add marubun's pcmcia driver
+
+ Marubun pcmcia is a chip for PCMCIA used with SuperH.
+ Of course, this can be used even by other architectures.
+ When use this driver, came to be able to use CompactFlash
+ and Ethernet.
+
+ Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+
+commit febd86b969b975289ed948f1ac0eb9722da41ced
+Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+Date: Sun Nov 25 02:32:13 2007 +0900
+
+ sh: Update SuperH SCIF driver
+
+ - Changed volatile unsigned to vu_.
+ - Changed Makefile for kconfig.
+
+ Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+
+commit 8be760903645af09871be50ad0a6f9ebb62b311d
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Nov 27 11:57:35 2007 +0100
+
+ ppc4xx: Kilauea & Makalu: Fix ext IRQ pin multiplexing
+
+ After an error in the AMCC 405EX users manual now correctly configure
+ IRQ2 (Kilauea)/IRQ0 (Makalu) as alternate 2 signal for external IRQ
+ usage.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit a5f601fd1b1278deae5aa9fc27a232b0d1c1c788
+Author: Wolfgang Denk <wd@denx.de>
+Date: Mon Nov 26 19:18:21 2007 +0100
+
+ Cleanup coding style; update CHANGELOG
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 3deca9d44767efd1b83f4b701f0dbf21a7595f7b
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sun Nov 25 22:39:25 2007 +0100
+
+ MAKEALL: add missing 512x boards in ppc
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit a340c325e668ca7386c2276387681720be9c3757
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sun Nov 25 18:45:47 2007 +0100
+
+ Makefile : fix tags ctags etags with new drivers organization
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 63362cfc6baa97ae0e37ba2c6ece530fcac9f79e
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Nov 26 15:06:14 2007 +0100
+
+ ppc4xx: Makalu: Change EBC setup for CS0 to enable 400MHz usage
+
+ As suggested by Senao, use a different EBC_PB0AP setup for 400MHz
+ operation.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit ca1ce226287270bb01e25b8e3674c701f12edf19
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Nov 26 15:01:45 2007 +0100
+
+ ppc4xx: Kilauea: Configure pin mux to use ext IRQ2 as interrupt
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 87ddedd6ad804427ce125ceaa076d7a4f74e9d5d
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sun Nov 25 18:45:47 2007 +0100
+
+ Makefile : fix tags ctags etags with new drivers organization
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 59829cc189378c142c13d2aa8d9a897d8bef3961
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sat Nov 24 21:26:56 2007 +0100
+
+ drivers/mtd : move mtd drivers to drivers/mtd
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 318c0b90431f2648552e5ade78833f42652ce859
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sat Nov 24 21:17:55 2007 +0100
+
+ drivers/misc : move misc drivers to drivers/misc
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 33daf5b7858807cb4ce4158c2c56524671c14c08
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sat Nov 24 21:13:59 2007 +0100
+
+ drivers/block : move block drivers to drivers/block
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 0c698dcaa70275eb8814f665b545547cee013892
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sat Nov 24 20:59:50 2007 +0100
+
+ drivers/rtc : move rtc drivers to drivers/rtc
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit f868cc5a50757d94f36c312395481cb0f187d9e6
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sat Nov 24 20:14:44 2007 +0100
+
+ drivers/hwmon : move hardware monitor drviers to drivers/hwmon
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 16b195c82a18cbfd164800f17a1ef9db2e48331a
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sat Nov 24 19:46:45 2007 +0100
+
+ drivers/input : move input drivers to drivers/input
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit e4558666293364fc3af1c1d9381ca933fa0f1275
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sat Nov 24 19:40:11 2007 +0100
+
+ drivers/usb : move usb drivers to drivers/usb
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 1378df792a7ff3abd1bf54a63f5475784f5b083c
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sat Nov 24 19:33:38 2007 +0100
+
+ drivers/serial : move serial drivers to drivers/serial
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 2439e4bfa111babf4bc07ba20efbf3e36036813e
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Wed Nov 21 21:19:24 2007 +0100
+
+ drivers/net : move net drivers to drivers/net
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 352d259130b349fe9593b8dada641bd78a9659e5
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Tue Nov 20 20:41:48 2007 +0100
+
+ drivers/video : move video drivers to drivers/video
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 73646217186aa17afc8e305c5f06f06dd335eaad
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Tue Nov 20 20:33:09 2007 +0100
+
+ drivers/pcmcia : move pcmcia drivers to drivers/pcmcia
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 93a686ee9c5ddc6fa368c32cfbfde6f6724599fc
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Tue Nov 20 20:28:09 2007 +0100
+
+ drivers/pci : move pci drivers to drivers/pci
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 9162352817579840d7802da6d85872b3ca003c97
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Thu Nov 22 17:23:23 2007 -0500
+
+ Fix fdt printing for updated libfdt
+
+ Also improve printing (adopt dtc v1 "c style" hex format), whitespace cleanup.
+
+ Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
+
+commit 9eb77cea1fa12d5969eb26a1d1d81da381bd6b1c
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Wed Nov 21 13:30:15 2007 -0600
+
+ Add additional fdt fixup helper functions
+
+ Added the following fdt fixup helpers:
+ * do_fixup_by_prop{_u32} - Find matching nodes by property name/value
+ * do_fixup_by_compat{_u32} - Find matching nodes by compat
+
+ The _u32 variants work the same only the property they are setting
+ is know to be a 32-bit integer instead of a byte buffer.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit ab544633abdd14f4dd5d92e500b73eb59ef57e67
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Wed Nov 21 11:11:03 2007 -0600
+
+ Add fdt_fixup_ethernet helper to set mac addresses
+
+ Added a fixup helper that uses aliases to set mac addresses
+ in the device tree based on the bd_t
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit dbaf07ce620aab249e3502b20a986234a6af1d3a
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Wed Nov 21 14:07:46 2007 -0600
+
+ Fix warnings from import of libfdt
+
+ cmd_fdt.c: In function fdt_print:
+ cmd_fdt.c:586: warning: assignment discards qualifiers from pointer target type
+ cmd_fdt.c:613: warning: assignment discards qualifiers from pointer target type
+ cmd_fdt.c:635: warning: assignment discards qualifiers from pointer target type
+ cmd_fdt.c:636: warning: assignment discards qualifiers from pointer target type
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 8d04f02f6224e6983f4812ea4da704950ec8539c
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Wed Oct 24 11:04:22 2007 -0500
+
+ Update libfdt from device tree compiler (dtc)
+
+ Update libfdt to commit 8eaf5e358366017aa2e846c5038d1aa19958314e from
+ the device tree compiler (dtc) project.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit e93becf80d732b64aef81b23e8b6ece02c40533d
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Sat Nov 3 19:46:28 2007 -0500
+
+ Move do_fixup* for libfdt into common code
+
+ Moved the generic fixup handling code out of cpu/mpc5xxx and cpu/mpc8260
+ into common/fdt_support.c and renamed:
+
+ do_fixup() -> do_fixup_by_path()
+ do_fixup_u32() -> do_fixup_by_path_u32()
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit f738b4a75998f42a7408defadc9baac7a31c92db
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Oct 25 16:15:07 2007 -0500
+
+ Make no options to fdt print default to '/'
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit a3c2933e02503fe36ade2c1b65af46f2b7a168e7
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Wed Oct 24 10:21:57 2007 -0500
+
+ Removed some nonused fdt functions and moved fdt_find_and_setprop out of libfdt
+
+ Removed:
+ fdt_node_is_compatible
+ fdt_find_node_by_type
+ fdt_find_compatible_node
+
+ To ease merge of newer libfdt as we aren't using them anywhere at this time.
+
+ Also moved fdt_find_and_setprop out of libfdt into fdt_support.c for the same
+ reason.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 98e2867cc85409b919f862e6c16026461ec955df
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Wed Nov 21 09:19:37 2007 -0700
+
+ [BUILD] Remove libraries when updating autoconf.mk
+
+ Fix library problems caused by conditional compilation. Using
+ autoconf.mk to decide which files to compile has caused a problem when
+ changing configuration from one board to another without clearing out
+ the library (*.a) files.
+
+ It used to be that the linker was always passed the same list of .o
+ files when building the .a files. However, that is not longer true
+ with conditional compilation. Now, a different board config will have
+ a different file list passed to the linker. The problem occurs when
+ a library has already been built and the board config is changed.
+
+ Since the linker will update instead of replace a preexisting library,
+ then if the file list changes to remove some object files the old
+ objects will still exist in the library.
+
+ The solution is to remove all old library files when autoconf.mk is
+ made.
+
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit ed1353d74b9ce8a7fcd660570b848a184d614b5f
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Wed Nov 21 08:49:50 2007 -0600
+
+ [BUILD] conditionally compile libfdt/*.c in libfdt/Makefile
+
+ Modify libfdt/Makefile to conditionally compile the *.c files based
+ on the board config.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
-commit 4a43719a7738712811d822ca8125427b27a55cdc
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Mon Sep 24 09:05:31 2007 -0600
+commit 4a43719a7738712811d822ca8125427b27a55cdc
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Mon Sep 24 09:05:31 2007 -0600
+
+ [BUILD] conditionally compile common/cmd_*.c in common/Makefile
+
+ Modify common/Makefile to conditionally compile the cmd_*.c files based
+ on the board config.
+
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 2f155f6c0a1f5e9a306a3f1f4fbe067db7ced3b1
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Mon Sep 24 09:05:31 2007 -0600
+
+ [BUILD] Generate include/autoconf.mk from board config files
+
+ Use cpp and sed to postprocess config.h and import the defined values
+ into include/autoconf.mk. autoconf.mk is then included by config.mk to
+ give 'make' access to the board configuration.
+
+ Doing this enables conditional compilation at the Makefile level instead
+ of by wrapping every .c file with #ifdef/#endif wrappers.
+
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 68b88999da87ab88e71e1306192905be3450198e
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Tue Nov 20 15:02:26 2007 -0600
+
+ 8610HPCD: Enable the 8610 Display Interface Unit
+
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 74f89faa9d1e77ed947e628d3effaa513fe05d05
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Tue Nov 20 15:00:53 2007 -0600
+
+ Move 8610 DIU interface structure definitions to header file.
+
+ These two structures are still needed during the
+ initialization and setup of the DIU hardware.
+ So move them to the fsl_diu_fb.h file for now.
+ Official "blah".
+
+ Noticed-by: York Sun <yorksun@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 080c646dbf474a109c3f85718fb01ce042a38c45
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Tue Nov 20 20:14:18 2007 +0100
+
+ drivers/i2c : move i2c drivers to drivers/i2c
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 9a337ddc154a10a26f117fd147b009abcdeba75a
+Author: Wolfgang Denk <wd@denx.de>
+Date: Mon Nov 19 22:20:24 2007 +0100
+
+ Prepare for 1.3.0 release.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit f30ad49b16bf998b03c1a5228b6c86369d61c258
+Author: Haiying Wang <Haiying.Wang@freescale.com>
+Date: Mon Nov 19 10:02:13 2007 -0500
+
+ Move CONFIG_QE out of CONFIG_PCI wrap for MPC8568MDS
+
+ CONFIG_QE shouldn't be in the wrap of CONFIG_PCI, fix it.
+
+ Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
+
+commit f8c320609366176b31104d9bf5e295232e1c7f1d
+Author: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
+Date: Mon Nov 19 11:14:16 2007 +0900
+
+ [MIPS] board/gth2/lowlevel_init.S: Fix a build warning
+
+ lowlevel_init.S: Assembler messages:
+ lowlevel_init.S:413: Warning: Pretending global symbol used as branch target is local.
+
+ Looking at codes, the `memtest' and `clearmem' are intentional mixed
+ use of `global symbols' and `label' for debugging purpose. To make it
+ build, just disable global-symbols-use for now. As a result `memtest'
+ still remains as unused, but leave it be...
+
+ Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
+
+commit e8da58f2bc092891e8cc92b927ed5c4bd0cb0cab
+Author: Wolfgang Denk <wd@denx.de>
+Date: Mon Nov 19 12:59:14 2007 +0100
+
+ Fix build problems with mp2usb board
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 6bf4c686afca1e86e1c384d59218f914605713bf
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sun Nov 18 18:36:11 2007 +0100
+
+ s3c24x0: Fix usb_ohci.c missing in Makefile
+ and usb_ohci.c warning differ in signedness
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 6073f61e078da5ddb521b56256bcc36508589883
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sun Nov 18 12:55:02 2007 +0100
+
+ pb1x00 board: Fix u16 status declaration when PCMCIA is defined
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 8412d814ce8bf5570a2b747f1e7fd321097fe987
+Author: Wolfgang Denk <wd@denx.de>
+Date: Sun Nov 18 17:11:09 2007 +0100
+
+ Fix compiler warnings for ARM systems.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 409ecdc0bb47dd28b0af6c25ffd658d22cc36b37
+Author: Wolfgang Denk <wd@denx.de>
+Date: Sun Nov 18 16:36:27 2007 +0100
+
+ Fix compiler warnings for PPC systems. Update CHANGELOG.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 653811a3c2b35856bf12e196dcc8c4694e28e420
+Author: Stefan Roese <sr@denx.de>
+Date: Sun Nov 18 14:44:44 2007 +0100
+
+ ppc4xx: Correct 405EX PCIe UTL register mapping
+
+ Map 4k mem space for UTL registers for each port.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 079c2c4fa71c0d1ebef394508df9088df8a308d3
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Sat Nov 17 11:31:10 2007 +0100
+
+ Fix warning differ in signedness in net/net.c and net/nfs.c
+
+commit 7e14fc65368cbd2861b1207453da55a4fc7b3f81
+Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+Date: Sat Nov 17 20:42:45 2007 +0900
+
+ gth2.c: Fix a warning on gth2 build.
+
+ gth2.c: In function 'misc_init_r':
+ gth2.c:434: warning: pointer targets in passing argument 2 of 'setenv' differ in signedness
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+
+commit 2309c130aa4c84b91bd874a41269c923eb61b555
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Nov 17 07:58:25 2007 +0100
+
+ Fix warning differ in signedness in common/cmd_scsi.c
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 9ea61b57968554eaf0f474ec7e088b17d367f474
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Nov 17 14:52:29 2007 +0100
+
+ ppc4xx: Update AMCC Kilauea config file
+
+ - Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE)
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 7e1d884b7cb602007329c517ec1c453e3a6a5d9c
+Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+Date: Sat Nov 17 20:05:26 2007 +0900
+
+ [MIPS] cpu/mips/config.mk: Fix GNU assembler minor version picker
+
+ Current trick to pick up GNU assembler minor version does not work with the
+ latest binutils (2007-03-01 or later) due to ${PKGVERSION} now default to
+ "(GNU Binutils) ".
+
+ $ sde-as --version |grep "GNU assembler"
+ GNU assembler 2.15.94 mipssde-6.02.02-20050602
+ $ sde-as --version |grep "GNU assembler" |awk '{print $3}'
+ 2.15.94
+ $ sde-as --version |grep "GNU assembler" |awk '{print $3}' |awk -F. '{print $2}'
+ 15
+ $
+
+ $ mips-linux-as --version |grep "GNU assembler"
+ GNU assembler (GNU Binutils) 2.18
+ $ mips-linux-as --version |grep "GNU assembler" |awk '{print $3}'
+ (GNU
+ $ mips-linux-as --version |grep "GNU assembler" |awk '{print $3}' |awk -F. '{print $2}'
+ (no output)
+ $
+
+ As a result of above, you'll see many noises with such binutils:
+
+ make -C cpu/mips/
+ /bin/sh: line 0: [: : integer expression expected
+ /bin/sh: line 0: [: : integer expression expected
+ make[1]: Entering directory `/home/skuribay/devel/u-boot.git/cpu/mips'
+ mips-linux-gcc -D__ASSEMBLY__ -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -c -o incaip_wdt.o incaip_wdt.S
+ /bin/sh: line 0: [: : integer expression expected
+ mips-linux-gcc -D__ASSEMBLY__ -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -c -o cache.o cache.S
+ /bin/sh: line 0: [: : integer expression expected
+ mips-linux-gcc -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -Wall -Wstrict-prototypes -c -o asc_serial.o asc_serial.c
+ /bin/sh: line 0: [: : integer expression expected
+
+ This patch simplifies the trick and makes it work with both versions of gas.
+ I also replace an expensive `awk (or gawk)' with `cut'.
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+
+commit 16664f72850846e645616da1c0fa5afcd6d15f15
+Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+Date: Sat Nov 17 20:05:26 2007 +0900
+
+ [MIPS] Remove useless instructions for initializing $gp.
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+
+commit 03c031d5660ea946c39af6e2e16267da857c609f
+Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+Date: Sat Oct 27 15:27:06 2007 +0900
+
+ [MIPS] MIPS 4K core: Coding style cleanups
+
+ No logical changes.
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+
+commit f5e429d3860bba4c6ae8bead8f78349fa24491b2
+Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+Date: Sat Nov 17 20:05:20 2007 +0900
+
+ [MIPS] gth2.c: Fix a warning on gth2 build.
+
+ gth2.c: In function 'misc_init_r':
+ gth2.c:434: warning: pointer targets in passing argument 2 of 'setenv' differ in signedness
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+
+commit 4fbd0741b2b6441da10be93e10267122581b7079
+Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+Date: Sat Oct 27 15:22:33 2007 +0900
+
+ [MIPS] au1x00_eth.c: Fixed a warning on pb1000 build.
+
+ au1x00_eth.c: In function 'au1x00_miiphy_write':
+ au1x00_eth.c:139: warning: 'return' with no value, in function returning non-void
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+
+commit f01320459736f156707425cf8112f98606301aa4
+Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+Date: Sat Oct 27 15:00:25 2007 +0900
+
+ [MIPS] au1x00_eth.c: Fix au1x00_miiphy_{read,write} build error
+
+ au1x00_eth.c: In function 'au1x00_enet_initialize':
+ au1x00_eth.c:246: error: 'au1x00_miiphy_read' undeclared (first use in this function)
+ au1x00_eth.c:246: error: (Each undeclared identifier is reported only once
+ au1x00_eth.c:246: error: for each function it appears in.)
+ au1x00_eth.c:246: error: 'au1x00_miiphy_write' undeclared (first use in this function)
+ au1x00_eth.c: In function 'au1x00_miiphy_write':
+ au1x00_eth.c:298: warning: 'return' with no value, in function returning non-void
+ make[1]: *** [au1x00_eth.o] Error 1
+
+ Fixed by moving these two functions forward.
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+
+commit b09258c5393edd1087c5f39ae68338f16b49f8b3
+Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+Date: Sat Oct 27 15:00:25 2007 +0900
+
+ MAKEALL: Added missing pb1000 board
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+
+commit 2e4a6e3667a1e39c0e6e99498686b15d2718b369
+Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+Date: Sat Oct 27 15:00:24 2007 +0900
+
+ [MIPS] pb1000: Replace obsolete memsetup.S with lowlevel_init.S
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+
+commit 662e5cb397249c3ea88a4c3255e9ccfc40b98d82
+Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+Date: Sat Oct 27 15:00:24 2007 +0900
+
+ [MIPS] u-boot.lds: Cleanup __u_boot_cmd_{start,end}
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+
+commit 5947f6999aafa7c54c1390983d264a8463dfea8e
+Author: Wolfgang Denk <wd@denx.de>
+Date: Sat Nov 17 02:34:38 2007 +0100
+
+ Update CHANGELOIG, prepare for -rc4
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit fd329e6f05bbdfe6bd71b0e09f0c76d3b0a025a5
+Author: Luotao Fu <l.fu@pengutronix.de>
+Date: Wed Nov 14 18:58:33 2007 +0100
+
+ Fix the i2c frequency and default address in rsdproto board
+
+ rsdproto board support has wrong I2C frequency and wrong return value
+ handling.
+
+ Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
+
+commit 429c180edad038f91c989cb14b478228092e7054
+Author: Wolfgang Denk <wd@denx.de>
+Date: Sat Nov 17 01:45:38 2007 +0100
+
+ powerpc: Backout relocation changes for MPC5121, too.
+
+ Apply Grant Likely's backout to MPC5121 code, too.
+
+ Pointed out by Rafal Jaworowski <raj@semihalf.com>
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 1c3dd43338a077165e7e0309cb3994e65d2bdbf8
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Tue Nov 13 22:18:33 2007 -0700
+
+ powerpc: Backout relocation changes.
+
+ Ugh. I *hate* to back this change out, but these compiler flags don't
+ work for relocation on all versions of GCC. I've not been able to
+ reproduce the environment in my setup (and hence, not been able to
+ find a combination that *does* work), so I've got no choice but to go
+ back to the old gcc flags and linker script.
+
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 5c15010efad980ad5498cc565fc1ed70df2f52b4
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Tue Nov 13 09:11:05 2007 +0100
+
+ Fixed mips_io_port_base build errors.
+
+ This patch has been sent on:
+ - 29 Sep 2007
+
+ Although mips_io_port_base is currently a part of IDE command, it is quite
+ fundamental for MIPS I/O port access such as in[bwl] and out[bwl]. So move
+ it to MIPS general part, and introduce `set_io_port_base()' from Linux.
+
+ This patch is triggered by multiple definition of `mips_io_port_base' build
+ error on gth2 (and tb0229 also needs this fix.)
+
+ board/gth2/libgth2.a(gth2.o): In function `log_serial_char':
+ /home/skuribay/devel/u-boot.git/board/gth2/gth2.c:47: multiple definition of `mips_io_port_base'
+ common/libcommon.a(cmd_ide.o):/home/skuribay/devel/u-boot.git/common/cmd_ide.c:712: first defined here
+ make: *** [u-boot] Error 1
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 6ecbb7a3fa9b0940ed33e490d195d4b6830b2422
+Author: Wolfgang Denk <wd@denx.de>
+Date: Sat Nov 17 01:30:40 2007 +0100
+
+ Fix a bug in the slave serial programming mode for the Xilinx
+ Spartan2/3 FPGAs. The old code used "< 0" on a "char" type to test if
+ the most significant bit was set, which did not work on any
+ architecture where "char" defaulted to be an unsigned type.
+
+ Based on a patch by Angelos Manousaridis <amanous@inaccessnetworks.com>
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit d08b7233bc252faad8339e7ca0ddfd62fa79903c
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Thu Nov 1 12:23:29 2007 -0500
+
+ 86xx: Fix broken variable reference when #def DEBUGing.
+
+ Sometimes you can't reference the DDR2 controller variables.
+
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit f9d9164d9c6b5a7f0393fd8d7e246b8a0326bc19
+Author: Jason Jin <Jason.jin@freescale.com>
+Date: Fri Oct 26 18:32:00 2007 +0800
+
+ make 8610 board use pixis reset
+
+ Signed-off-by: Jason Jin <Jason.jin@freescale.com>
+
+commit db74b3c1c9481a6bffbf8cd445e5bcbf6908e836
+Author: Jason Jin <Jason.jin@freescale.com>
+Date: Mon Oct 29 19:26:21 2007 +0800
+
+ Unify pixis_reset altbank across board families
+
+ Basically, refactor the CFG_PIXIS_VBOOT_MASK values
+ into the separate board config files.
+
+ Signed-off-by: Jason Jin <Jason.jin@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 64bf555465c7926be13e1046ac0d0f05ac72829c
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Wed Nov 7 08:19:21 2007 +0100
+
+ Fix warning: pointer targets in assignment differ in signedness
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 7a60ee7c6248a958c5757d3660a1702723a2786d
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Wed Nov 7 08:19:19 2007 +0100
+
+ Fix warning differ in signedness in common/cmd_ide.c
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit f31d38b9eea9b32f6a1ac848a298cc71ca4c9a03
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Nov 16 14:16:54 2007 +0100
+
+ ppc4xx: Enable 405EX PCIe UTL register configuration
+
+ Till now the UTL registers on 405EX were not initialized but left with
+ their default values. This patch new initializes some of the UTL
+ registers on 405EX.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit ecdcbd4f8c1f8cefd785752f4e7536aae2a4ecf9
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Nov 16 14:00:59 2007 +0100
+
+ ppc4xx: Update AMCC Makalu for board rev 1.1
+
+ This patch adds changes needed for Makalu rev 1.1:
+
+ - Enable 2nd DDR2 bank resulting in 256MByte of SDRAM
+ - Enable 2nd ethernet port EMAC1
+ - Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE)
+ - Reset PCIe ports via GPIO upon bootup
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 4d4faae65e115e327425cd514c1a35146a85166b
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Mon Sep 24 09:05:31 2007 -0600
+
+ Group PCI and PCMCIA drivers in drivers/Makefile
+
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 5798f87dc10a496d79d3177b9f5a76488987fd35
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Mon Sep 24 09:05:31 2007 -0600
+
+ Group block/flash drivers in drivers/Makefile
+
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit df58c81551700f058b44cacf55a7997fa63bfe0a
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Mon Sep 24 09:05:31 2007 -0600
+
+ Group USB drivers in drivers/Makefile
+
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 5dbb6ed622e539b0c8493ef7e578d3a533181d29
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Mon Sep 24 09:05:30 2007 -0600
+
+ Group i2c drivers in drivers/Makefile
+
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit ec00c76de0e5971273905998d62d6bb119324218
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Mon Sep 24 09:05:30 2007 -0600
+
+ Group console drivers in drivers/Makefile
+
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 754f230aa01b8c789fc31f8013c2487954073300
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Mon Sep 24 09:05:30 2007 -0600
+
+ Group network drivers in drivers/Makefile
+
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit f0037c56b0d12cd46215124667b9f83d60ef9391
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Mon Sep 24 09:05:30 2007 -0600
+
+ Build: split COBJS value into multiple lines
+
+ This change is in preparation for condtitionial compile support in the
+ build system. By spliting them all into seperate lines now, subsequent
+ patches that change 'COBJS-y += ' into 'COBJS-$(CONFIG_<blah>) += ' will
+ be less invasive and easier to review
+
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 1b4aaffe4fb2a5e95d9111a5d94fd1f89215dce4
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Mon Sep 24 09:05:30 2007 -0600
+
+ Add .gitignore files
+
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+ Acked-by: Kim Phillips <kim.phillips@freescale.com>
+
+commit 955413f35f054a82e40042f1dbcf501c6a05719b
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Thu Nov 15 08:27:52 2007 -0700
+
+ Revert "Correct relocation fixup for mpc5xx"
+
+ This reverts commit 3649cd99ba815b6601868735765602f00ef3692b.
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit e15633888a058aacb31a62d2cf1278e1e4c236ab
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Thu Nov 15 08:24:32 2007 -0700
+
+ Revert "Correct fixup relocation for MPC5xxx"
+
+ This reverts commit 6f7576b20ecf0d040c3ac3b032b5cbc860e38a90.
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 139365fbe566d0fc619a1ed04452ec5388f0cef8
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Thu Nov 15 08:21:04 2007 -0700
+
+ Revert "Correct fixup relocation for mpc8220"
+
+ This reverts commit a85dd254c0577fca13627c46e93fc2ad4c4f1f00.
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 70922342369e5e39b286fe21e768a239ca07a514
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Thu Nov 15 08:20:57 2007 -0700
+
+ Revert "Correct fixup relocation for mpc824x"
+
+ This reverts commit f3a52fe05923935db86985daf9438e2f70ac39aa.
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 96279ab4cad60cb5972aa934fbe4845ac02cc75a
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Thu Nov 15 08:20:50 2007 -0700
+
+ Revert "Correct fixup relocation for mpc8260"
+
+ This reverts commit 5af61b2f4b838a05f79be274f3e5a66edd2d9c96.
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 928fe33b24cdf382a8dc8687fed24b1961cdb5d6
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Thu Nov 15 08:20:43 2007 -0700
+
+ Revert "Correct fixup relocation for mpc83xx"
+
+ This reverts commit 057004f4a4863554d56cc56268bfa7c7d9738e27.
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit c93945e8f9e300860d2bf73a2549ce5794f8bd00
+Author: Grant Likely <grant.likely@secretlab.ca>
+Date: Thu Nov 15 08:20:25 2007 -0700
+
+ Revert "[MPC512x] Correct fixup relocation"
+
+ This reverts commit 8d17979d0359492a822a0a409d26e3a3549b4cd4.
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit c9672f81f1bdb4e8ddf62aa72ca0206e8b72aa1c
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Nov 15 14:25:09 2007 +0100
+
+ ppc4xx: Small AMCC Kilauea cleanup
+
+ Remove not needed pci_target_init() function.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit aee747f19b460a0e9da20ff21e90fdaac1cec359
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Nov 15 14:23:55 2007 +0100
+
+ ppc4xx: Enable 440 GPIO init table CFG_440_GPIO_TABLE for 405 platforms
+
+ - Rename CFG_440_GPIO_TABLE to CFG_4xx_GPIO_TABLE
+ - Cleanup of the 4xx GPIO functions
+ - Move some GPIO defines from the cpu headers ppc405.h/ppc440.h into gpio.h
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 8ada0ebf38e4073beea0309188b25d82a112a2ae
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Nov 15 14:20:08 2007 +0100
+
+ ppc4xx: AMCC Taihu board config file cleanup
+
+ This patch makes the AMCC Taihu a little more compatible to the other
+ AMCC eval boards.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 5e71c51d74c963d3174060c078dcacf13bdd02ef
+Author: Marian Balakowicz <m8@semihalf.com>
+Date: Thu Nov 15 13:37:28 2007 +0100
+
+ [INKA4x0] NG hardware: flash support
+
+ Disabled and remove inka4x0 custom flash driver, use CFI flash
+ driver instead.
+
+ Signed-off-by: Marian Balakowicz <m8@semihalf.com>
+
+commit 5fb6d7191e206cdde0e23140fd8111caed93a595
+Author: Marian Balakowicz <m8@semihalf.com>
+Date: Thu Nov 15 13:29:55 2007 +0100
+
+ [INKA4x0] NG hardware: SDRAM support
+
+ Add support for three new DDR chips that may be present on a NG
+ INKA4x0 hardware: HYB25D512160BF-5, K4H511638C-7CB3, T46V32M16BN-6IT.
+
+ Cleanup board/inka4x0/mt48lc16m16a2-75.h file.
+
+ Signed-off-by: Marian Balakowicz <m8@semihalf.com>
+
+commit f23cb34c367bb27585a4fdb8a75277370e7d0596
+Author: Marian Balakowicz <m8@semihalf.com>
+Date: Thu Nov 15 13:24:43 2007 +0100
+
+ [INKA4x0] NG hardware: platform code update
+
+ - Cleanup compile warnings.
+ - Add missing '\0' in default environment.
+ - Increase CFG_MONITOR_LEN to 256 KiB.
+ - Add required CFG_USE_PPCENV.
+
+ Signed-off-by: Marian Balakowicz <m8@semihalf.com>
+
+commit 2ae64f5135e51bb18753884d1265b99e89b5aedd
+Author: Peter Pearse <peter.pearse@arm.com>
+Date: Thu Nov 15 08:58:00 2007 +0000
+
+ Remove warnings re CONFIG_EXTRA_ENV_SETTINGS
+ Remove warnings re onenand_read() & write()
+
+commit 2db916e14410e3ec1738508c7bf4dfeb2b299ae7
+Author: Peter Pearse <peter.pearse@arm.com>
+Date: Thu Nov 15 08:45:13 2007 +0000
+
+ Correction patch
+
+commit 1d8a49eca1c7bdc8db1c47a92f9014a29ead03ae
+Author: Roy Zang <tie-fei.zang@freescale.com>
+Date: Thu Sep 13 18:52:28 2007 +0800
+
+ Enable ULi1575 Ethernet support in 8610HPCD config
+
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+ Acked-by: Jon Loeliger <jdl@freescale.com>
+
+commit 54fd6c93c28a0a45352fff5dd92673401ff563f2
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Nov 13 08:18:20 2007 +0100
+
+ ppc4xx: lwmon5: Change PHY reset sequence for PHY MDIO address latching
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 7d0a4066b5a6b698e5fc1b66cfe9705774bbce93
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Nov 13 08:06:11 2007 +0100
+
+ ppc4xx: Fix 405EX PCIe UTLSET register setup
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 1ce55151c85d068f70317a8d65c61058b891afb4
+Author: Heiko Schocher <hs@denx.de>
+Date: Tue Nov 13 07:50:29 2007 +0100
+
+ [UC101] SRAM now with 2 MB working.
+
+ Signed-off-by: Heiko Schocher <hs@denx.de>
+
+commit 2d14684341109a69616e4d6016cd61402d55086f
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Fri Nov 9 15:37:53 2007 +0100
+
+ ppc4xx: Use generic usb-ohci driver for sequoia board
+
+ This patch makes the sequoia board use the generic usb-ohci driver
+ instead of cpu/ppc4xx/usb_ohci.c.
+
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 9be659ac0868dc367caa957c5c725e46b07f6a5f
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Fri Nov 9 15:37:23 2007 +0100
+
+ ppc4xx: Make USB working with CONFIG_4xx_DCACHE defined
+
+ This patch disables the 44x d-cache on 'usb start' and
+ reenables it on 'usb stop'. This should be seen as a
+ temporary fix until the generic usb-ohci driver can
+ life with d-cache enabled.
+
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit fbde2169d2c48fcc9ff03489534a78ffb0a8a0d4
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Fri Nov 9 15:36:44 2007 +0100
+
+ ppc4xx: Remove redundant code from 4xx network driver
+
+ This patch removes some redundant code and decrements the end
+ address of cache flush and invalidate by 1.
+
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 5ca9881aad8c413ac2a82868a5e3719178254502
+Author: Peter Pearse <peter.pearse@arm.com>
+Date: Fri Nov 9 15:24:26 2007 +0000
+
+ Add apollon board support
+ Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
+
+commit b53313dbfc74525d85f1e7e0102f902d5c863beb
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Nov 9 12:19:58 2007 +0100
+
+ ppc4xx: Remove In:/Out:/Err: boot output for AMCC Kilauea
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit c7f69c340277935a6c19a956421852da944a365f
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Nov 9 12:18:54 2007 +0100
+
+ ppc4xx: Make output a little shorter on I2C bootrom detection
+
+ Most 4xx PPC capable of using an I2C bootrom for bootstrap setting
+ already print a line with the information which I2C bootrom is
+ used for bootstrap configuration. So we don't need this extra line
+ with "I2C boot EEPROM en-/dis-abled".
+
+ This patch also has a little code cleanup integrated.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 8d737a28152ec12873f8544cca1fb39a49e5e693
+Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+Date: Thu Nov 8 12:50:18 2007 -0600
+
+ ColdFire: MCF5329 - Remove reset registers from CCM
+
+ Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+
+commit 7d7cdea769a60b0a6e4c18bef7f9d648fd14b8d7
+Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+Date: Thu Nov 8 12:31:11 2007 -0600
+
+ ColdFire: MCF5329 - Add Reset structure to immap_5329.h
+
+ Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+
+commit 09b26cf00d76d75fdf7fdc4b13e4dd929743bc21
+Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+Date: Thu Nov 8 12:19:01 2007 -0600
+
+ ColdFire: MCF5329 - revert include/asm-m68k/m5329.h file mode
+
+ Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+
+commit 225a24b5e062ad94627424508ae814f51dbe1a34
+Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+Date: Wed Nov 7 18:00:54 2007 -0600
+
+ ColdFire: MCF5445x - Update correct RAMBAR and missing linker files
+
+ Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+
+commit 248c7c14835f34d5d910b45e5600050e58ca6cab
+Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+Date: Wed Nov 7 17:56:15 2007 -0600
+
+ ColdFire: MCF532x - Update do_reset() using core reset
+
+ Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+
+commit d9240a5f827eb3b476a6ba2938d01f1a9e7688f4
+Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+Date: Wed Nov 7 17:51:00 2007 -0600
+
+ ColdFire: Update cpu flag for 4.2-xx compiler
+
+ Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+
+commit 070ba56115b4da63b46e974287fa4550d4023386
+Author: York Sun <yorksun@freescale.com>
+Date: Wed Oct 31 14:59:04 2007 -0500
+
+ 8610: Add console frame buffer support to FSL 8610 DIU driver.
+
+ Add cfb console support to FSL 8610 DIU driver.
+ Inspect board version from PIXIS to obtain correct pixel format.
+
+ Use #define CONFIG_VIDEO in config file to enable fb console.
+
+ To switch monitor, set monitor variable to
+ 0 - DVI, 1 - Single link LVDS, 2 - Double link LVDS
+ followed by "diufb init".
+
+ Preserve logo bitmap at the top of the fb console.
+
+ Signed-off-by: York Sun <yorksun@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit a877880c6949e948bd63cd6ea4e216573d2f53dd
+Author: York Sun <yorksun@freescale.com>
+Date: Mon Oct 29 13:58:39 2007 -0500
+
+ 8610: Add 8610 DIU display driver
+
+ 1280x1024 and 1024x768 @ 32 bpp are supported now.
+ DVI, Single-link LVDS, Double-link LVDS are all supported.
+
+ Environmental variable "monitor" is used to specify monitor port.
+
+ A new command "diufb" is introduced to reinitialize monitor
+ and display a BMP file in the memory. So far, 1-bit, 4-bit,
+ 8-bit and 24-bit BMP formats are supported.
+
+ diufb init
+ - initialize the diu driver
+ Enable the port specified in the environmental variable "monitor"
+
+ diufb addr
+ - display bmp file in memory.
+ The bmp image should be no bigger than the resolution, 1280x1024
+ for DVI and double-link LVDS, 1024x768 for single-link LVDS.
+
+ Note, this driver allocate memory but doesn't free it after use
+ It is written on purpose -- to avoid a failure of reallocation
+ due to memory fragement.
+
+ ECC of DDR is disabled for DIU performance. L2 data cache is also disabled.
+
+ Signed-off-by: York Sun <yorksun@freescale.com>
+ Signed-off-by: Jon loeliger <jdl@freescale.com>
+
+commit 52e5ddfecdda308f75782fae206b677b1810f5f9
+Author: York Sun <yorksun@freescale.com>
+Date: Wed Oct 31 10:43:59 2007 -0500
+
+ FSL: Add a freescale bitmap logo.
+
+ This Freescale logo is a 340 x 128 x 4bpp BMP file
+ that can be displayed by the DIU Framebuffer driver.
+
+ Signed-off-by: York Sun <yorksun@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 1815338fbd1c0f94f8276d2891b99caa5a05f622
+Author: York Sun <yorksun@freescale.com>
+Date: Mon Oct 29 13:57:53 2007 -0500
+
+ 8610: Make some extra debug environment variables conditional.
+
+ One may #define ENV_DEBUG to get them back again.
+
+ Signed-off-by: York Sun <yorksun@freescale.com>
+
+commit 761421ccca80a9fb37b19c37aa61d46ef75e0647
+Author: Jason Jin <Jason.jin@freescale.com>
+Date: Mon Oct 29 19:26:21 2007 +0800
+
+ 8610: Actually enable pixis_reset CONFIGs
+
+ Signed-off-by: Jason Jin <Jason.jin@freescale.com>
+
+commit f3bceaab230b4748d0afc4109b6837308f018b40
+Author: Jason Jin <Jason.jin@freescale.com>
+Date: Fri Oct 26 18:31:59 2007 +0800
+
+ Fix the BAT definition of PCI IO on 8610 board
+
+ The address in the BAT register is aligned with the BAT size.
+ The original definition actually did not define BAT for PCIE2 IO.
+ This patch fix this.
+
+ Signed-off-by: Jason Jin <Jason.jin@freescale.com>
+
+commit 9f23ca334a6f5f021ef9e9d0fad9da80d63b2d56
+Author: Jason Jin <Jason.jin@freescale.com>
+Date: Mon Oct 29 19:26:21 2007 +0800
+
+ Unify pixis_reset altbank across board families
+
+ Basically, refactor the CFG_PIXIS_VBOOT_MASK values
+ into the separate board config files.
+
+ Signed-off-by: Jason Jin <Jason.jin@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit a8318ec205c8e8794b5f9f1b8584abadb440e8ba
+Author: Jason Jin <Jason.jin@freescale.com>
+Date: Fri Oct 26 18:32:00 2007 +0800
+
+ make 8610 board use pixis reset
+
+ Signed-off-by: Jason Jin <Jason.jin@freescale.com>
+
+commit 9c84709eedce9c680dd695984ab7d2328f4f04f5
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Thu Nov 1 12:23:29 2007 -0500
+
+ 86xx: Fix broken variable reference when #def DEBUGing.
+
+ Sometimes you can't reference the DDR2 controller variables.
+
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 1f103105a3746ab12279b63b8c1d372c0ce2cc58
+Author: Roy Zang <tie-fei.zang@freescale.com>
+Date: Mon Nov 5 17:39:24 2007 +0800
+
+ Implement general ULi 526x Ethernet driver support in U-boot
+
+ This patch implements general ULi 526x Ethernet driver.
+ Until now, it is the only native Ethernet port on
+ MPC8610HPCD board, but it could be used on other boards
+ with ULi 526x Ethernet port as well.
+
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+ Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
+ Acked-by: Jon Loeliger <jdl@freescale.com>
+ Signed-off-by: Ben Warren <bwarren@qstreams.com>
+
+commit 71bc6e6474fea8ef481b9b45d1edd7ad1f6dfbbd
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Thu Nov 1 08:46:50 2007 -0500
+
+ NET: Add Ethernet 1000BASE-X support for PPC4xx
+
+ This patch adds support for 1000BASE-X to functions "miiphy_speed ()" and
+ "miiphy_duplex()". It also adds function "miiphy_is_1000base_x ()", which
+ returns non-zero iff the PHY registers are configured for 1000BASE-X. The
+ "mii info" command is modified to distinguish between 1000BASE-T and -X.
+
+ Signed-off-by: Larry Johnson <lrj@acm.org>
+ Signed-off-by: Ben Warren <bwarren@qstreams.com>
+
+commit 298035df4948b113d29ac0e694717d34b95bc5dc
+Author: Larry Johnson <lrj@arlinx.com>
+Date: Wed Oct 31 11:21:29 2007 -0500
+
+ NET: Cosmetic changes
+
+ Signed-off-by: Larry Johnson <lrj@acm.org>
+ Signed-off-by: Ben Warren <bwarren@qstreams.com>
- [BUILD] conditionally compile common/cmd_*.c in common/Makefile
+commit 654f38b3a387886996a5a75771fbfc29cb4f225e
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Nov 5 07:43:05 2007 +0100
- Modify common/Makefile to conditionally compile the cmd_*.c files based
- on the board config.
+ ppc4xx: Make output a little shorter on PCIe detection
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+ Now not max 3 lines but 2 lines are printed per PCIe port.
-commit 2f155f6c0a1f5e9a306a3f1f4fbe067db7ced3b1
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Mon Sep 24 09:05:31 2007 -0600
+ Signed-off-by: Stefan Roese <sr@denx.de>
- [BUILD] Generate include/autoconf.mk from board config files
+commit 992742a5b09d9040adbd156fb90756af66ade310
+Author: Wolfgang Denk <wd@denx.de>
+Date: Sat Nov 3 23:09:27 2007 +0100
- Use cpp and sed to postprocess config.h and import the defined values
- into include/autoconf.mk. autoconf.mk is then included by config.mk to
- give 'make' access to the board configuration.
+ Cleanup coding style; update CHANGELOG
- Doing this enables conditional compilation at the Makefile level instead
- of by wrapping every .c file with #ifdef/#endif wrappers.
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+commit e881cb563e32f45832b7b6db77bdcd017adcbb41
+Author: Bruce Adler <bruce.adler@ccpu.com>
+Date: Fri Nov 2 13:15:42 2007 -0700
-commit 080c646dbf474a109c3f85718fb01ce042a38c45
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Tue Nov 20 20:14:18 2007 +0100
+ fix wording in README
- drivers/i2c : move i2c drivers to drivers/i2c
+ Changed the wording to properly describe the shadowing
+ of the environment from ROM to RAM
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ Signed-off-by: Bruce Adler <bruce.adler@acm.org>
-commit 9a337ddc154a10a26f117fd147b009abcdeba75a
-Author: Wolfgang Denk <wd@denx.de>
-Date: Mon Nov 19 22:20:24 2007 +0100
+commit ad845beef06245426c57b53dcdc01b7dc70e0d45
+Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+Date: Wed Oct 31 02:18:15 2007 +0900
- Prepare for 1.3.0 release.
+ blackfin: Move `-D__BLACKFIN__' to $(ARCH)_config.mk
- Signed-off-by: Wolfgang Denk <wd@denx.de>
+ Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-commit f30ad49b16bf998b03c1a5228b6c86369d61c258
-Author: Haiying Wang <Haiying.Wang@freescale.com>
-Date: Mon Nov 19 10:02:13 2007 -0500
+commit ec22755799466c8a103664bb3a5e647bf9c238f4
+Author: Vlad Lungu <vlad@comsys.ro>
+Date: Thu Oct 25 16:08:14 2007 +0300
- Move CONFIG_QE out of CONFIG_PCI wrap for MPC8568MDS
+ Trimmed some variables in ne2000.c
- CONFIG_QE shouldn't be in the wrap of CONFIG_PCI, fix it.
+ Signed-off-by: Vlad Lungu <vlad@comsys.ro>
- Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
+commit eb6f214d3644b2a77968c176ed36dcf858cfe7e0
+Author: Zhang Wei <wei.zhang@freescale.com>
+Date: Thu Oct 25 17:51:27 2007 +0800
-commit f8c320609366176b31104d9bf5e295232e1c7f1d
-Author: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
-Date: Mon Nov 19 11:14:16 2007 +0900
+ Fix the issue of usb_kbd driver missing the scan code of key 'z'.
- [MIPS] board/gth2/lowlevel_init.S: Fix a build warning
+ The scan code of the key 'z' is 0x1d, which should be handled.
- lowlevel_init.S: Assembler messages:
- lowlevel_init.S:413: Warning: Pretending global symbol used as branch target is local.
+ The change has be tested on NOVATEK USB keyboard and ULI PCI OHCI
+ controller.
- Looking at codes, the `memtest' and `clearmem' are intentional mixed
- use of `global symbols' and `label' for debugging purpose. To make it
- build, just disable global-symbols-use for now. As a result `memtest'
- still remains as unused, but leave it be...
+ Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
- Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
+commit bbf4796f6498fbade56d56eff3a0a49b299d93e5
+Author: Zhang Wei <wei.zhang@freescale.com>
+Date: Thu Oct 25 17:30:04 2007 +0800
-commit e8da58f2bc092891e8cc92b927ed5c4bd0cb0cab
-Author: Wolfgang Denk <wd@denx.de>
-Date: Mon Nov 19 12:59:14 2007 +0100
+ Fix USB support issue for MPC8641HPCN board.
- Fix build problems with mp2usb board
+ The configuration file has already enabled USB, but it
+ missed definition of CFG_OHCI_SWAP_REG_ACCESS, the USB
+ on MPC8641HPCN can not work because of the wrong USB
+ register endian.
- Signed-off-by: Wolfgang Denk <wd@denx.de>
+ And add the USB command to U-Boot commands list.
-commit 6bf4c686afca1e86e1c384d59218f914605713bf
+ Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
+
+commit 4e62041023dc3de9d98d977bb080235bc6d035e0
Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sun Nov 18 18:36:11 2007 +0100
+Date: Wed Oct 24 18:16:01 2007 +0200
- s3c24x0: Fix usb_ohci.c missing in Makefile
- and usb_ohci.c warning differ in signedness
+ Use config_cmd_default.h instead of config_cmd_all.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-commit 6073f61e078da5ddb521b56256bcc36508589883
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sun Nov 18 12:55:02 2007 +0100
+commit 56622f87857439b1c221e9deef11a9d5bb5d4308
+Author: Marian Balakowicz <m8@semihalf.com>
+Date: Wed Oct 24 01:37:36 2007 +0200
- pb1x00 board: Fix u16 status declaration when PCMCIA is defined
+ TQM5200: Call usb_cpu_init() during board init
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ usb_cpu_init() configures GPS USB pins, clocks, etc. and
+ is required for proper operation of kernel USB subsystem.
+ This setup was previously done in the kernel by the fixup
+ code which is being removed, thus low level init must be
+ done by U-boot now.
-commit 8412d814ce8bf5570a2b747f1e7fd321097fe987
-Author: Wolfgang Denk <wd@denx.de>
-Date: Sun Nov 18 17:11:09 2007 +0100
+ Signed-off-by: Marian Balakowicz <m8@semihalf.com>
- Fix compiler warnings for ARM systems.
+commit 29c29c0267fe857e72014ce90c5d35b2ef6302bd
+Author: Guennadi Liakhovetski <lg@denx.de>
+Date: Tue Oct 23 16:25:50 2007 +0200
- Signed-off-by: Wolfgang Denk <wd@denx.de>
+ Fix typo in nfs.c
-commit 409ecdc0bb47dd28b0af6c25ffd658d22cc36b37
-Author: Wolfgang Denk <wd@denx.de>
-Date: Sun Nov 18 16:36:27 2007 +0100
+ An obvious typo. Originally fixed in linkstation u-boot port.
- Fix compiler warnings for PPC systems. Update CHANGELOG.
+ Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
- Signed-off-by: Wolfgang Denk <wd@denx.de>
+commit 59543fe00a4ce720ef9f5aa7fb387c6daf1c7d78
+Author: Guennadi Liakhovetski <lg@denx.de>
+Date: Tue Oct 23 14:35:05 2007 +0200
-commit 079c2c4fa71c0d1ebef394508df9088df8a308d3
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Sat Nov 17 11:31:10 2007 +0100
+ Fix a typo in cpu/mpc824x/interrupts.c
- Fix warning differ in signedness in net/net.c and net/nfs.c
+ Since December 2003 the timer_interrupt_cpu() function in
+ cpu/mpc824x/interrupts.c contains what seems to be a superfluous
+ parameter. Remove it.
-commit 7e14fc65368cbd2861b1207453da55a4fc7b3f81
-Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-Date: Sat Nov 17 20:42:45 2007 +0900
+ Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
- gth2.c: Fix a warning on gth2 build.
+commit c9e7b9b9a1700fe009678d1f9b41e6364ac5df2d
+Author: Sergej Stepanov <Sergej.Stepanov@ids.de>
+Date: Wed Oct 17 11:13:51 2007 +0200
- gth2.c: In function 'misc_init_r':
- gth2.c:434: warning: pointer targets in passing argument 2 of 'setenv' differ in signedness
+ add ft_cpu_setup(..) on mpc8260
- Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+ Add ft_cpu_setup(..)-function to adapt it for use with libfdt
+ based on code from mpc5xxx
-commit 2309c130aa4c84b91bd874a41269c923eb61b555
+ Sigend-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
+ --
+
+commit 6abd82e19ae93c0b4d104e50165e235915ec0875
+Author: Sergej Stepanov <Sergej.Stepanov@ids.de>
+Date: Wed Oct 17 11:18:42 2007 +0200
+
+ changes for IDS8247 board support
+
+ To get the IDS8247 board working following are done:
+ - FCC2 is deactivated
+ - FCC1 is activated
+ - I2C is activated
+ - CFI driver is activated
+ - Adapted for use with LIBFDT
+
+ Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
+ --
+
+commit 3d6cb3b24add6415f86a0f013ea40f5639b90047
Author: Stefan Roese <sr@denx.de>
-Date: Sat Nov 17 07:58:25 2007 +0100
+Date: Sat Nov 3 12:08:28 2007 +0100
- Fix warning differ in signedness in common/cmd_scsi.c
+ ppc4xx: Add AMCC Kilauea/Haleakala NAND booting support
+
+ This patch adds NAND booting support for the AMCC 405EX(r) eval boards.
+ Again, only one image supports both targets.
Signed-off-by: Stefan Roese <sr@denx.de>
-commit 7e1d884b7cb602007329c517ec1c453e3a6a5d9c
-Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-Date: Sat Nov 17 20:05:26 2007 +0900
+commit 8b6684a698500be9c142ec2c9f46cfc348e17f0c
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Wed Oct 24 15:48:37 2007 +0200
- [MIPS] cpu/mips/config.mk: Fix GNU assembler minor version picker
+ ATSTK1002: Remove default ethernet addresses
- Current trick to pick up GNU assembler minor version does not work with the
- latest binutils (2007-03-01 or later) due to ${PKGVERSION} now default to
- "(GNU Binutils) ".
+ Wolfgang is right: It's not a good idea to set up default initial
+ ethernet addresses for a board, even though they belong to the local
+ range.
- $ sde-as --version |grep "GNU assembler"
- GNU assembler 2.15.94 mipssde-6.02.02-20050602
- $ sde-as --version |grep "GNU assembler" |awk '{print $3}'
- 2.15.94
- $ sde-as --version |grep "GNU assembler" |awk '{print $3}' |awk -F. '{print $2}'
- 15
- $
+ This will change the failure mode from "IT manager screams at you for
+ using duplicate ethernet addresses" to a nice error message explaining
+ that the ethernet address hasn't been set properly.
- $ mips-linux-as --version |grep "GNU assembler"
- GNU assembler (GNU Binutils) 2.18
- $ mips-linux-as --version |grep "GNU assembler" |awk '{print $3}'
- (GNU
- $ mips-linux-as --version |grep "GNU assembler" |awk '{print $3}' |awk -F. '{print $2}'
- (no output)
- $
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
- As a result of above, you'll see many noises with such binutils:
+commit e5c794e491a57d829b6d8733e2ed8368a2269abf
+Author: Justin Flammia <jflammia@savantav.com>
+Date: Mon Oct 29 17:40:35 2007 -0400
- make -C cpu/mips/
- /bin/sh: line 0: [: : integer expression expected
- /bin/sh: line 0: [: : integer expression expected
- make[1]: Entering directory `/home/skuribay/devel/u-boot.git/cpu/mips'
- mips-linux-gcc -D__ASSEMBLY__ -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -c -o incaip_wdt.o incaip_wdt.S
- /bin/sh: line 0: [: : integer expression expected
- mips-linux-gcc -D__ASSEMBLY__ -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -c -o cache.o cache.S
- /bin/sh: line 0: [: : integer expression expected
- mips-linux-gcc -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -Wall -Wstrict-prototypes -c -o asc_serial.o asc_serial.c
- /bin/sh: line 0: [: : integer expression expected
+ DHCP Client Fix
- This patch simplifies the trick and makes it work with both versions of gas.
- I also replace an expensive `awk (or gawk)' with `cut'.
+ This is a multi-part message in MIME format.
- Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+ commit e6e505eae94ed721e123e177489291fc4544b7b8
+ Author: Justin Flammia <jflammia@savantav.com>
+ Date: Mon Oct 29 17:19:03 2007 -0400
-commit 16664f72850846e645616da1c0fa5afcd6d15f15
-Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-Date: Sat Nov 17 20:05:26 2007 +0900
+ Found a bug in the way the DHCP Request packet is built, where the IP address
+ that is offered by the server is bound to prematurely. This patch is a fix of
+ that bug where the IP address offered by the DHCP server is not used until
+ after the DHCP ACK from the server is received.
- [MIPS] Remove useless instructions for initializing $gp.
+ Signed-off-by: Justin Flammia <jflammia@savantav.com>
+ Signed-off-by: Ben Warren <bwarren@qstreams.com>
- Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+commit 5d96d40d3f36da33348e68f9ea993f383e11f997
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 31 20:58:34 2007 +0100
-commit 03c031d5660ea946c39af6e2e16267da857c609f
-Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-Date: Sat Oct 27 15:27:06 2007 +0900
+ ppc4xx: Fix acadia_nand build problem
- [MIPS] MIPS 4K core: Coding style cleanups
+ Since the cache handling functions were moved from start.S into cache.S
+ the acadia NAND booting Makfile needs to be adapted accordingly.
- No logical changes.
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+commit ea2e142843533ca593fcb5cb3e1daf1b7f5e5949
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 31 20:57:11 2007 +0100
-commit f5e429d3860bba4c6ae8bead8f78349fa24491b2
-Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-Date: Sat Nov 17 20:05:20 2007 +0900
+ ppc4xx: Add CONFIG_4xx_DCACHE compile options to enable cached SDRAM
+
+ This patch adds the CONFIG_4xx_DCACHE options to some SDRAM init files
+ and to the Sequoia TLB init code. Now the cache can be enabled on 44x
+ boards by defining CONFIG_4xx_DCACHE in the board config file. This
+ option will disappear, when more boards use is successfully and no
+ more known problems exist.
+
+ This is tested successfully on Sequoia and Katmai. The only problem that
+ needs to be fixed is, that USB is not working on Sequoia right now, since
+ it will need some cache handling code too, similar to the 4xx EMAC driver.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
- [MIPS] gth2.c: Fix a warning on gth2 build.
+commit 3db93b8bedd32e914b38976141b3fdf4ea3ff738
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 31 20:51:10 2007 +0100
- gth2.c: In function 'misc_init_r':
- gth2.c:434: warning: pointer targets in passing argument 2 of 'setenv' differ in signedness
+ ppc4xx: Enable CPU POST test for 4xx with dcache enabled
- Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+ Now with caches enabled (i- and d-cache) on 44x, we need a chance to
+ disable the cache for the CPU POST tests, since these tests consist
+ of self modifying code. This is done via the new change_tlb() function.
-commit 4fbd0741b2b6441da10be93e10267122581b7079
-Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-Date: Sat Oct 27 15:22:33 2007 +0900
+ Signed-off-by: Stefan Roese <sr@denx.de>
- [MIPS] au1x00_eth.c: Fixed a warning on pb1000 build.
+commit f71b2888b4b3c870909a0341427b2a914246f81f
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 31 20:47:26 2007 +0100
- au1x00_eth.c: In function 'au1x00_miiphy_write':
- au1x00_eth.c:139: warning: 'return' with no value, in function returning non-void
+ ppc4xx: Change 4xx POST ethernet test to handle cached memory too
- Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+ This patch enables the 4xx EMAC POST driver to work too, when dcache is
+ enabled.
-commit f01320459736f156707425cf8112f98606301aa4
-Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-Date: Sat Oct 27 15:00:25 2007 +0900
+ Signed-off-by: Stefan Roese <sr@denx.de>
- [MIPS] au1x00_eth.c: Fix au1x00_miiphy_{read,write} build error
+commit a2685904061b35a17583d65fe47cdc2686a69eaa
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 31 20:45:53 2007 +0100
- au1x00_eth.c: In function 'au1x00_enet_initialize':
- au1x00_eth.c:246: error: 'au1x00_miiphy_read' undeclared (first use in this function)
- au1x00_eth.c:246: error: (Each undeclared identifier is reported only once
- au1x00_eth.c:246: error: for each function it appears in.)
- au1x00_eth.c:246: error: 'au1x00_miiphy_write' undeclared (first use in this function)
- au1x00_eth.c: In function 'au1x00_miiphy_write':
- au1x00_eth.c:298: warning: 'return' with no value, in function returning non-void
- make[1]: *** [au1x00_eth.o] Error 1
+ ppc4xx: Remove temporary TLB entry in POST cache test only for 440
- Fixed by moving these two functions forward.
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+commit ff768cb168d8157c24a25016dbfbeb465e47f420
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 31 18:01:24 2007 +0100
-commit b09258c5393edd1087c5f39ae68338f16b49f8b3
-Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-Date: Sat Oct 27 15:00:25 2007 +0900
+ ppc4xx: Change 4xx ethernet driver to handle cached memory too
- MAKEALL: Added missing pb1000 board
+ This patch enables the 4xx EMAC driver to work too, when dcache is
+ enabled.
- Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+ Signed-off-by: Stefan Roese <sr@denx.de>
-commit 2e4a6e3667a1e39c0e6e99498686b15d2718b369
-Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-Date: Sat Oct 27 15:00:24 2007 +0900
+commit 483e09a223c666269ef81d3573a6591b1046b0ef
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 31 17:59:22 2007 +0100
- [MIPS] pb1000: Replace obsolete memsetup.S with lowlevel_init.S
+ ppc4xx: Add change_tlb function to modify I attribute of TLB(s)
- Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+ This function is used to either turn cache on or off in a specific
+ memory area.
-commit 662e5cb397249c3ea88a4c3255e9ccfc40b98d82
-Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-Date: Sat Oct 27 15:00:24 2007 +0900
+ Signed-off-by: Stefan Roese <sr@denx.de>
- [MIPS] u-boot.lds: Cleanup __u_boot_cmd_{start,end}
+commit d25dfe08fbd1220cb994e7e6b105049aa9aa8e79
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 31 17:57:52 2007 +0100
- Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+ ppc4xx: Remove cache definition from 4xx board config files
-commit 5947f6999aafa7c54c1390983d264a8463dfea8e
-Author: Wolfgang Denk <wd@denx.de>
-Date: Sat Nov 17 02:34:38 2007 +0100
+ All 4xx board config files don't need the cache definitions anymore.
+ These are now defined in common headers.
- Update CHANGELOIG, prepare for -rc4
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Wolfgang Denk <wd@denx.de>
+commit 9b94ac61d2176185c30adf0793e079ec30e68687
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 31 17:55:58 2007 +0100
-commit fd329e6f05bbdfe6bd71b0e09f0c76d3b0a025a5
-Author: Luotao Fu <l.fu@pengutronix.de>
-Date: Wed Nov 14 18:58:33 2007 +0100
+ ppc4xx: Rework 4xx cache support
- Fix the i2c frequency and default address in rsdproto board
+ New cache handling functions added and all existing functions
+ moved from start.S into seperate cache.S.
- rsdproto board support has wrong I2C frequency and wrong return value
- handling.
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
+commit 06713773da4ac3d390c63d82641eb553224b27c2
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Oct 23 18:03:12 2007 +0200
-commit 429c180edad038f91c989cb14b478228092e7054
-Author: Wolfgang Denk <wd@denx.de>
-Date: Sat Nov 17 01:45:38 2007 +0100
+ ppc4xx: Remove compiler warning from previous commit
- powerpc: Backout relocation changes for MPC5121, too.
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Apply Grant Likely's backout to MPC5121 code, too.
+commit 6fa397df67c0f269e4528bf181a6e8c88f9723f9
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Oct 23 14:40:30 2007 +0200
- Pointed out by Rafal Jaworowski <raj@semihalf.com>
+ ppc4xx: Remove temporary TLB entry in POST cache test
- Signed-off-by: Wolfgang Denk <wd@denx.de>
+ Signed-off-by: Stefan Roese <sr@denx.de>
-commit 1c3dd43338a077165e7e0309cb3994e65d2bdbf8
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Tue Nov 13 22:18:33 2007 -0700
+commit 1338e6a81834099ba19733b69aafd8ef5f098094
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Oct 23 14:05:08 2007 +0200
- powerpc: Backout relocation changes.
+ ppc4xx: Change autonegotiation timeout from 4 to 5 seconds
- Ugh. I *hate* to back this change out, but these compiler flags don't
- work for relocation on all versions of GCC. I've not been able to
- reproduce the environment in my setup (and hence, not been able to
- find a combination that *does* work), so I've got no choice but to go
- back to the old gcc flags and linker script.
+ I lately noticed, that newer 4xx board with GBit support sometimes don't
+ finish link autonegotiation in 4 seconds. Changing this timeout to 5
+ seconds seems fine here.
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+ Signed-off-by: Stefan Roese <sr@denx.de>
-commit 5c15010efad980ad5498cc565fc1ed70df2f52b4
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Tue Nov 13 09:11:05 2007 +0100
+commit 2d83476a4c1c9911d158a3f8a4312d354bc1bdb7
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Oct 23 14:03:17 2007 +0200
- Fixed mips_io_port_base build errors.
+ ppc4xx: Change 4xx_enet & miiphy to use out_be32() and friends
- This patch has been sent on:
- - 29 Sep 2007
+ This patch changes all in32/out32 calls to use the recommended in_be32/
+ out_be32 macros instead.
- Although mips_io_port_base is currently a part of IDE command, it is quite
- fundamental for MIPS I/O port access such as in[bwl] and out[bwl]. So move
- it to MIPS general part, and introduce `set_io_port_base()' from Linux.
+ Signed-off-by: Stefan Roese <sr@denx.de>
- This patch is triggered by multiple definition of `mips_io_port_base' build
- error on gth2 (and tb0229 also needs this fix.)
+commit 7d47cee2cc57f907380f2c06f5b6c683d03e423a
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Oct 25 12:24:59 2007 +0200
- board/gth2/libgth2.a(gth2.o): In function `log_serial_char':
- /home/skuribay/devel/u-boot.git/board/gth2/gth2.c:47: multiple definition of `mips_io_port_base'
- common/libcommon.a(cmd_ide.o):/home/skuribay/devel/u-boot.git/common/cmd_ide.c:712: first defined here
- make: *** [u-boot] Error 1
+ ppc4xx: Fix POST ethernet test for Haleakala
- Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ The POST ethernet test needed to be changed to dynamically determine
+ the count of ethernet devices. This code is cloned from the 4xx
+ ethernet driver.
-commit 6ecbb7a3fa9b0940ed33e490d195d4b6830b2422
-Author: Wolfgang Denk <wd@denx.de>
-Date: Sat Nov 17 01:30:40 2007 +0100
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Fix a bug in the slave serial programming mode for the Xilinx
- Spartan2/3 FPGAs. The old code used "< 0" on a "char" type to test if
- the most significant bit was set, which did not work on any
- architecture where "char" defaulted to be an unsigned type.
+commit f10493c6d77a1e07a6c2ff4d772937a5e7359d6a
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Oct 23 11:31:05 2007 +0200
- Based on a patch by Angelos Manousaridis <amanous@inaccessnetworks.com>
+ ppc4xx: Correct UART input clock calculation and passing to fdt
- Signed-off-by: Wolfgang Denk <wd@denx.de>
+ We now use a value in the gd (global data) structure for the UART input
+ frequency, since the PPC4xx_SYS_INFO struct is always rewritten completely
+ in get_sys_info().
-commit d08b7233bc252faad8339e7ca0ddfd62fa79903c
-Author: Jon Loeliger <jdl@freescale.com>
-Date: Thu Nov 1 12:23:29 2007 -0500
+ Signed-off-by: Stefan Roese <sr@denx.de>
- 86xx: Fix broken variable reference when #def DEBUGing.
+commit 353f2688b4e0fc7b969bc70a02be4b40bf0dd124
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Oct 23 10:10:08 2007 +0200
- Sometimes you can't reference the DDR2 controller variables.
+ ppc4xx: Add initial AMCC Haleakala PPC405EXr eval board support
- Signed-off-by: Jon Loeliger <jdl@freescale.com>
+ The Haleakala is nearly identical with the Kilauea eval board. The only
+ difference is that the 405EXr only supports one EMAC and one PCIe
+ interface. This patch adds support for the Haleakala board by using
+ the identical image for Kilauea and Haleakala. The distinction is done
+ by comparing the PVR.
-commit f9d9164d9c6b5a7f0393fd8d7e246b8a0326bc19
-Author: Jason Jin <Jason.jin@freescale.com>
-Date: Fri Oct 26 18:32:00 2007 +0800
+ Signed-off-by: Stefan Roese <sr@denx.de>
- make 8610 board use pixis reset
+commit 9f798766aa85e62eb8fa8c721e148df609b78137
+Author: Eugene O'Brien <eugene.obrien@advantechamt.com>
+Date: Tue Oct 23 08:29:10 2007 +0200
- Signed-off-by: Jason Jin <Jason.jin@freescale.com>
+ ppc4xx: Fixed offset of refresh rate type for Bamboo on-board DDR SDRAM
-commit db74b3c1c9481a6bffbf8cd445e5bcbf6908e836
-Author: Jason Jin <Jason.jin@freescale.com>
-Date: Mon Oct 29 19:26:21 2007 +0800
+ This patch also adds a note to the fixed DDR setup for Bamboo NAND booting:
- Unify pixis_reset altbank across board families
+ Note:
+ As found out by Eugene O'Brien <eugene.obrien@advantechamt.com>, the fixed
+ DDR setup has problems (U-Boot crashes randomly upon TFTP), when the DIMM
+ modules are still plugged in. So it is recommended to remove the DIMM
+ modules while using the NAND booting code with the fixed SDRAM setup!
- Basically, refactor the CFG_PIXIS_VBOOT_MASK values
- into the separate board config files.
+ Signed-off-by: Eugene O'Brien <eugene.obrien@advantechamt.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Jason Jin <Jason.jin@freescale.com>
- Signed-off-by: Jon Loeliger <jdl@freescale.com>
+commit afe9fa59cb63b4f9d16bf01c93eb212f25a38c2a
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Oct 22 16:24:44 2007 +0200
-commit 64bf555465c7926be13e1046ac0d0f05ac72829c
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Wed Nov 7 08:19:21 2007 +0100
+ ppc4xx: Add SNTP support to AMCC Katmai, Kilauea & Makalu boards
- Fix warning: pointer targets in assignment differ in signedness
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+commit 3248f63ad89cb031491edb7016587fe6e9a238b9
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Oct 22 16:22:40 2007 +0200
-commit 7a60ee7c6248a958c5757d3660a1702723a2786d
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Wed Nov 7 08:19:19 2007 +0100
+ ppc4xx: Rework of 4xx serial driver (4)
- Fix warning differ in signedness in common/cmd_ide.c
+ Change 4xx_uart.c:
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ - Use in_8/out_8 macros instead of in8/out8
+ - No need for UART_BASE marco anymore, now really handled via function
+ parameter
+ - serial_init_common() introduced
+ - Further coding style cleanup
-commit 4d4faae65e115e327425cd514c1a35146a85166b
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Mon Sep 24 09:05:31 2007 -0600
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Group PCI and PCMCIA drivers in drivers/Makefile
+commit e61cb8163a66b8a135696ae232e2bead1ce0a049
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Oct 22 15:45:49 2007 +0200
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+ ppc4xx: Rework of 4xx serial driver (3)
-commit 5798f87dc10a496d79d3177b9f5a76488987fd35
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Mon Sep 24 09:05:31 2007 -0600
+ Change all linker scripts to reference the changed driver name iop480_uart.o.
- Group block/flash drivers in drivers/Makefile
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+commit 882ae41274921f9016131806bdeb27e19606f47a
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Oct 22 15:44:39 2007 +0200
-commit df58c81551700f058b44cacf55a7997fa63bfe0a
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Mon Sep 24 09:05:31 2007 -0600
+ ppc4xx: Rework of 4xx serial driver (2)
- Group USB drivers in drivers/Makefile
+ Change all linker scripts to reference the changed driver name 4xx_uart.o.
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+ Note: In most cased all these explicit referencing of these object files
+ in the linker scripts is not neccessary. Only for manually embedded
+ environment into the U-Boot image, which is not done is most cases.
-commit 5dbb6ed622e539b0c8493ef7e578d3a533181d29
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Mon Sep 24 09:05:30 2007 -0600
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Group i2c drivers in drivers/Makefile
+commit ad31e40bed042cb670d0036fea96435007afb838
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Oct 22 15:09:59 2007 +0200
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+ ppc4xx: Rework of 4xx serial driver (1)
-commit ec00c76de0e5971273905998d62d6bb119324218
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Mon Sep 24 09:05:30 2007 -0600
+ This patch starts the rework of the PPC4xx serial driver. First we split
+ the file into two seperate files, one 4xx_uart.c with the 405/440 UART
+ handling code and the other one iop480_uart.c with the UART code for the
+ PLX-Tech IOP480 PPC (PPC403 based).
- Group console drivers in drivers/Makefile
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+commit 764e7417ee5f6e25b1715720e7d7dd3487109385
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Oct 22 10:30:38 2007 +0200
-commit 754f230aa01b8c789fc31f8013c2487954073300
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Mon Sep 24 09:05:30 2007 -0600
+ ppc4xx: Correct UART input clock calculation and passing to fdt
- Group network drivers in drivers/Makefile
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+commit 211ea91ac6c225bec7e668a03d0ba7d7310679fa
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Oct 22 07:34:34 2007 +0200
-commit f0037c56b0d12cd46215124667b9f83d60ef9391
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Mon Sep 24 09:05:30 2007 -0600
+ ppc4xx: Add initial AMCC Makalu 405EX support
- Build: split COBJS value into multiple lines
+ Signed-off-by: Stefan Roese <sr@denx.de>
- This change is in preparation for condtitionial compile support in the
- build system. By spliting them all into seperate lines now, subsequent
- patches that change 'COBJS-y += ' into 'COBJS-$(CONFIG_<blah>) += ' will
- be less invasive and easier to review
+commit fa8aea20456e6f1dba43f46bcc72024dd9499998
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Oct 22 07:33:52 2007 +0200
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+ ppc4xx: Add freqUART to CPU speed detection
-commit 1b4aaffe4fb2a5e95d9111a5d94fd1f89215dce4
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Mon Sep 24 09:05:30 2007 -0600
+ This value is needed later for the device tree configuration of
+ the uart clock.
- Add .gitignore files
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
- Acked-by: Kim Phillips <kim.phillips@freescale.com>
+commit 837c730b4d7c6b1ddf3d1e247cb4445005d9bf0d
+Author: Stefan Roese <sr@denx.de>
+Date: Sun Oct 21 14:26:29 2007 +0200
-commit 955413f35f054a82e40042f1dbcf501c6a05719b
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Thu Nov 15 08:27:52 2007 -0700
+ ppc: Small Kilauea cleanup of config file
- Revert "Correct relocation fixup for mpc5xx"
+ Signed-off-by: Stefan Roese <sr@denx.de>
- This reverts commit 3649cd99ba815b6601868735765602f00ef3692b.
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+commit 758c037aeead34b49631b8da3a90b1bba14c0410
+Author: Stefan Roese <sr@denx.de>
+Date: Sun Oct 21 08:16:12 2007 +0200
-commit e15633888a058aacb31a62d2cf1278e1e4c236ab
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Thu Nov 15 08:24:32 2007 -0700
+ rtc: Add Xicor/Intersil X1205 RTC support
- Revert "Correct fixup relocation for MPC5xxx"
+ This patch adds support for the Xicor/Intersil X1205 RTC used on the
+ AMCC Makalu eval board. This driver is basically cloned from the Linux
+ driver version (2.6.23).
- This reverts commit 6f7576b20ecf0d040c3ac3b032b5cbc860e38a90.
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+ This patch also introduces the Linux bcd.h header for the BCD2BIN/
+ BIN2BCD conversions. In the future some of the other U-Boot RTC driver
+ should be converted to also use this header instead of implementing
+ their own local copy of these functions/macros.
-commit 139365fbe566d0fc619a1ed04452ec5388f0cef8
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Thu Nov 15 08:21:04 2007 -0700
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Revert "Correct fixup relocation for mpc8220"
+commit 087dfdb79b5fd1ab99a26990c62a732c01a8c7f6
+Author: Stefan Roese <sr@denx.de>
+Date: Sun Oct 21 08:12:41 2007 +0200
- This reverts commit a85dd254c0577fca13627c46e93fc2ad4c4f1f00.
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+ ppc4xx: Consolidate some of the 405 and 440 macros/structs into 4xx
-commit 70922342369e5e39b286fe21e768a239ca07a514
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Thu Nov 15 08:20:57 2007 -0700
+ This patch moves some common 4xx macros and the PPC405_SYS_INFO/
+ PPC440_SYS_INFO structure into the common ppc4xx.h header.
- Revert "Correct fixup relocation for mpc824x"
+ Lot's of other macros are good candidates to be consolidated this way
+ in the future.
- This reverts commit f3a52fe05923935db86985daf9438e2f70ac39aa.
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+ Signed-off-by: Stefan Roese <sr@denx.de>
-commit 96279ab4cad60cb5972aa934fbe4845ac02cc75a
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Thu Nov 15 08:20:50 2007 -0700
+commit 770c7af5800f598d22730d1f4b70f16c9b33512e
+Author: Stefan Roese <sr@denx.de>
+Date: Sun Oct 21 08:05:18 2007 +0200
- Revert "Correct fixup relocation for mpc8260"
+ ppc4xx: Fix size setup in Kilauea DDR2 init routine
- This reverts commit 5af61b2f4b838a05f79be274f3e5a66edd2d9c96.
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+ The size was initilized wrong. Instead of 256MB, the DDR2 controller
+ was setup to 512MB. Now the correct values is used.
-commit 928fe33b24cdf382a8dc8687fed24b1961cdb5d6
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Thu Nov 15 08:20:43 2007 -0700
+ This patch also does a little cleanup and adds a comment here.
- Revert "Correct fixup relocation for mpc83xx"
+ Signed-off-by: Stefan Roese <sr@denx.de>
- This reverts commit 057004f4a4863554d56cc56268bfa7c7d9738e27.
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+commit f6ba9b56607d4b27550301c7c7f6b55b654fd62a
+Author: Eugene O'Brien <eugene.obrien@advantechamt.com>
+Date: Thu Oct 18 17:29:04 2007 +0200
-commit c93945e8f9e300860d2bf73a2549ce5794f8bd00
-Author: Grant Likely <grant.likely@secretlab.ca>
-Date: Thu Nov 15 08:20:25 2007 -0700
+ ppc4xx: Define CONFIG_BOOKE for all PPC440 based processors
- Revert "[MPC512x] Correct fixup relocation"
+ CONFIG_BOOKE must be defined for PPC440 processors so that the proper SPR
+ number is used to access system registers.
- This reverts commit 8d17979d0359492a822a0a409d26e3a3549b4cd4.
- Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+ Signed-off-by: Eugene O'Brien <eugene.obrien@advantechamt.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
-commit 54fd6c93c28a0a45352fff5dd92673401ff563f2
+commit c36c68160333ac5fe41ec3db12a728b7075b3912
Author: Stefan Roese <sr@denx.de>
-Date: Tue Nov 13 08:18:20 2007 +0100
+Date: Thu Oct 18 07:42:27 2007 +0200
- ppc4xx: lwmon5: Change PHY reset sequence for PHY MDIO address latching
+ ppc4xx: Change inbound PCIe location for endpoint tests on Katmai
- Signed-off-by: Stefan Roese <sr@denx.de>
+ On Yucca & Katmai, the inbound memory map pointed to 0x4.0000.0000, which
+ is the internal SRAM. Since I now ported and tested this endpoint mode
+ on Kilauea successfully to map to 0 (SDRAM), I also changed this for
+ Katmai.
-commit 1ce55151c85d068f70317a8d65c61058b891afb4
-Author: Heiko Schocher <hs@denx.de>
-Date: Tue Nov 13 07:50:29 2007 +0100
+ Yucca will stay at internal SRAM for now. Not sure if somebody relies on
+ this setup.
- [UC101] SRAM now with 2 MB working.
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Heiko Schocher <hs@denx.de>
+commit 5cb4af4791f61843432155142b6cfac901f66c10
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Oct 18 07:39:38 2007 +0200
-commit 8d737a28152ec12873f8544cca1fb39a49e5e693
-Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
-Date: Thu Nov 8 12:50:18 2007 -0600
+ ppc4xx: Add PCIe endpoint support on Kilauea (405EX)
- ColdFire: MCF5329 - Remove reset registers from CCM
+ This patch adds endpoint support for the AMCC Kilauea eval board. It can
+ be tested by connecting a reworked PCIe cable (only 1x lane singles
+ connected) to another root-complex.
- Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+ In this test setup, a 64MB inbound window is configured at BAR0 which maps
+ to 0 on the PLB side. So accessing this BAR0 from the root-complex will
+ access the first 64MB of the SDRAM on the PPC side.
-commit 7d7cdea769a60b0a6e4c18bef7f9d648fd14b8d7
-Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
-Date: Thu Nov 8 12:31:11 2007 -0600
+ Signed-off-by: Stefan Roese <sr@denx.de>
- ColdFire: MCF5329 - Add Reset structure to immap_5329.h
+commit d4cb2d17946466740afeb195a57d6cb290bf4cc0
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Oct 13 16:43:23 2007 +0200
- Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+ ppc4xx: Dynamic configuration of 4xx PCIe mode as root or endpoint mode
-commit 09b26cf00d76d75fdf7fdc4b13e4dd929743bc21
-Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
-Date: Thu Nov 8 12:19:01 2007 -0600
+ This patch adds support for dynamic configuration of PCIe ports for the
+ AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe
+ boards Yucca & Katmai and the 405EX board Kilauea.
- ColdFire: MCF5329 - revert include/asm-m68k/m5329.h file mode
+ This dynamic configuration is done via the "pcie_mode" environement
+ variable. This variable can be set to "EP" or "RP" for endpoint or
+ rootpoint mode. Multiple values can be joined via the ":" delimiter.
+ Here an example:
- Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+ pcie_mode=RP:EP:EP
-commit 225a24b5e062ad94627424508ae814f51dbe1a34
-Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
-Date: Wed Nov 7 18:00:54 2007 -0600
+ This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2
+ as endpoint.
- ColdFire: MCF5445x - Update correct RAMBAR and missing linker files
+ Per default Yucca will be configured as:
+ pcie_mode=RP:EP:EP
- Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+ Per default Katmai will be configured as:
+ pcie_mode=RP:RP:REP
-commit 248c7c14835f34d5d910b45e5600050e58ca6cab
-Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
-Date: Wed Nov 7 17:56:15 2007 -0600
+ Per default Kilauea will be configured as:
+ pcie_mode=RP:RP
- ColdFire: MCF532x - Update do_reset() using core reset
+ Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+commit fd671802b67a0ef37a06124fa2ce85f00aa22c6f
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Oct 11 11:15:59 2007 +0200
-commit d9240a5f827eb3b476a6ba2938d01f1a9e7688f4
-Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
-Date: Wed Nov 7 17:51:00 2007 -0600
+ ppc4xx: Enable device tree support (fdt) on Kilauea per default
- ColdFire: Update cpu flag for 4.2-xx compiler
+ This patch enables the fdt support on the AMCC Kilauea eval board.
+ Additionally now EBC ranges fdt fixup is included to support NOR
+ FLASH mapping via the Linux physmap_of driver.
- Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
+ This Kilauea port now support booting arch/ppc and arch/powerpc
+ Linux kernels. The default environment "net_nfs" is for arch/ppc
+ and "net_nfs_fdt" is for arch/powerpc. In the long run, arch/ppc
+ support will be removed.
-commit 1f103105a3746ab12279b63b8c1d372c0ce2cc58
-Author: Roy Zang <tie-fei.zang@freescale.com>
-Date: Mon Nov 5 17:39:24 2007 +0800
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Implement general ULi 526x Ethernet driver support in U-boot
+commit 4994ffd890b9d95d807387a9b7bd8a4803ee406e
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Oct 11 11:11:45 2007 +0200
- This patch implements general ULi 526x Ethernet driver.
- Until now, it is the only native Ethernet port on
- MPC8610HPCD board, but it could be used on other boards
- with ULi 526x Ethernet port as well.
+ ppc4xx: Add additional debug info to 4xx fdt support
- Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
- Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
- Acked-by: Jon Loeliger <jdl@freescale.com>
- Signed-off-by: Ben Warren <bwarren@qstreams.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
-commit 71bc6e6474fea8ef481b9b45d1edd7ad1f6dfbbd
-Author: Larry Johnson <lrj@arlinx.com>
-Date: Thu Nov 1 08:46:50 2007 -0500
+commit db3232ddb058d0ed0bc31f7c5c296748a1afac67
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Oct 5 21:28:58 2007 +0200
- NET: Add Ethernet 1000BASE-X support for PPC4xx
+ ppc4xx: Fix small merge problems with CPCI440 and Acadia boards
- This patch adds support for 1000BASE-X to functions "miiphy_speed ()" and
- "miiphy_duplex()". It also adds function "miiphy_is_1000base_x ()", which
- returns non-zero iff the PHY registers are configured for 1000BASE-X. The
- "mii info" command is modified to distinguish between 1000BASE-T and -X.
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Larry Johnson <lrj@acm.org>
- Signed-off-by: Ben Warren <bwarren@qstreams.com>
+commit 1941cce71b1ae975602854045061e82f94ecd012
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Oct 5 17:35:10 2007 +0200
-commit 298035df4948b113d29ac0e694717d34b95bc5dc
-Author: Larry Johnson <lrj@arlinx.com>
-Date: Wed Oct 31 11:21:29 2007 -0500
+ ppc4xx: Fix small merge problem in 4xx_enet.c
- NET: Cosmetic changes
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Larry Johnson <lrj@acm.org>
- Signed-off-by: Ben Warren <bwarren@qstreams.com>
+commit 566806ca1a1bf4d895daaf0b2ba5494abbffebaf
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Oct 5 17:11:30 2007 +0200
-commit 992742a5b09d9040adbd156fb90756af66ade310
-Author: Wolfgang Denk <wd@denx.de>
-Date: Sat Nov 3 23:09:27 2007 +0100
+ ppc4xx: Add initial AMCC Kilauea 405EX support
- Cleanup coding style; update CHANGELOG
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Wolfgang Denk <wd@denx.de>
+commit dbbd125721aea6645fdb962f36bd41f59e272f9d
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Oct 5 17:10:59 2007 +0200
-commit e881cb563e32f45832b7b6db77bdcd017adcbb41
-Author: Bruce Adler <bruce.adler@ccpu.com>
-Date: Fri Nov 2 13:15:42 2007 -0700
+ ppc4xx: Add PPC405EX support
- fix wording in README
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Changed the wording to properly describe the shadowing
- of the environment from ROM to RAM
+commit 1d7b874e9c9a7c66f5d8da9ec78a3733765d3e31
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Oct 5 17:09:36 2007 +0200
- Signed-off-by: Bruce Adler <bruce.adler@acm.org>
+ ppc4xx: Cleanup of 4xx PCI and PCIe support (renaming)
-commit ad845beef06245426c57b53dcdc01b7dc70e0d45
-Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-Date: Wed Oct 31 02:18:15 2007 +0900
+ Signed-off-by: Stefan Roese <sr@denx.de>
- blackfin: Move `-D__BLACKFIN__' to $(ARCH)_config.mk
+commit 4f14ed6230b9c109aac9a6fb878497dabd44c2db
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Oct 5 17:07:50 2007 +0200
- Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+ ppc4xx: Add initial fdt support to 4xx (first needed on 405EX)
-commit ec22755799466c8a103664bb3a5e647bf9c238f4
-Author: Vlad Lungu <vlad@comsys.ro>
-Date: Thu Oct 25 16:08:14 2007 +0300
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Trimmed some variables in ne2000.c
+commit a424a8bb2924b90724b944165d3141f1fa8dfe5b
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Oct 5 17:04:57 2007 +0200
- Signed-off-by: Vlad Lungu <vlad@comsys.ro>
+ POST: Add 405EX support to 4xx UART POST test
-commit eb6f214d3644b2a77968c176ed36dcf858cfe7e0
-Author: Zhang Wei <wei.zhang@freescale.com>
-Date: Thu Oct 25 17:51:27 2007 +0800
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Fix the issue of usb_kbd driver missing the scan code of key 'z'.
+commit 4f2e92c11f6e2392fc8187829211a5ca7f0c1e12
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Oct 5 15:10:02 2007 +0200
- The scan code of the key 'z' is 0x1d, which should be handled.
+ DTT: Prepare DS1775 driver for use of different I2C addresses
- The change has be tested on NOVATEK USB keyboard and ULI PCI OHCI
- controller.
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
+commit 19e93b1e16d267220440d827b920fbad8abfa70f
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Oct 5 14:23:43 2007 +0200
-commit bbf4796f6498fbade56d56eff3a0a49b299d93e5
-Author: Zhang Wei <wei.zhang@freescale.com>
-Date: Thu Oct 25 17:30:04 2007 +0800
+ ppc4xx: 4xx_pcie: Change PCIe status output to match common style
- Fix USB support issue for MPC8641HPCN board.
+ Signed-off-by: Stefan Roese <sr@denx.de>
- The configuration file has already enabled USB, but it
- missed definition of CFG_OHCI_SWAP_REG_ACCESS, the USB
- on MPC8641HPCN can not work because of the wrong USB
- register endian.
+commit ff68f66bcb0da847845aa2fac11eba6c25938c99
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Oct 5 09:22:33 2007 +0200
- And add the USB command to U-Boot commands list.
+ ppc4xx: 4xx_pcie: Disable debug output as default
- Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
-commit 4e62041023dc3de9d98d977bb080235bc6d035e0
-Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-Date: Wed Oct 24 18:16:01 2007 +0200
+commit 97923770cb52b64d69eec958a11b2eda8d46e0f7
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Oct 5 09:18:23 2007 +0200
- Use config_cmd_default.h instead of config_cmd_all.h
+ ppc4xx: 4xx_pcie: More general cleanup and 405EX PCIe support added
- Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
-commit 56622f87857439b1c221e9deef11a9d5bb5d4308
-Author: Marian Balakowicz <m8@semihalf.com>
-Date: Wed Oct 24 01:37:36 2007 +0200
+commit 4dbee8a90df613eb517aadbecebd70f168913d30
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Oct 5 07:57:20 2007 +0200
- TQM5200: Call usb_cpu_init() during board init
+ ppc4xx: 4xx_pcie: Change CFG_PCIE_MEMSIZE to 128MB on Yucca & Katmai
- usb_cpu_init() configures GPS USB pins, clocks, etc. and
- is required for proper operation of kernel USB subsystem.
- This setup was previously done in the kernel by the fixup
- code which is being removed, thus low level init must be
- done by U-boot now.
+ 128MB seems to be the smallest possible value for the memory size
+ for on PCIe port. With this change now the BAR's of the PCIe cards
+ are accessible under U-Boot.
- Signed-off-by: Marian Balakowicz <m8@semihalf.com>
+ One big note: This only works for PCIe port 0 & 1. For port 2 this
+ currently doesn't work, since the base address is now 0xc0000000
+ (0xb0000000 + 2 * 0x08000000), and this is already occupied by
+ CFG_PCIE0_CFGBASE. But solving this issue for port 2 would mean
+ to change the base addresses completely and this change would have
+ too much impact right now.
-commit 29c29c0267fe857e72014ce90c5d35b2ef6302bd
-Author: Guennadi Liakhovetski <lg@denx.de>
-Date: Tue Oct 23 16:25:50 2007 +0200
+ This patch adds debug output to the 4xx pcie driver too.
- Fix typo in nfs.c
+ Signed-off-by: Stefan Roese <sr@denx.de>
- An obvious typo. Originally fixed in linkstation u-boot port.
+commit 6d95289281ed2958ebf76d2b55f86bbd88591fd2
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 3 21:16:32 2007 +0200
- Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
+ ppc4xx: 4xx_pcie: Fix problem with SDRN access using port number as idx
-commit 59543fe00a4ce720ef9f5aa7fb387c6daf1c7d78
-Author: Guennadi Liakhovetski <lg@denx.de>
-Date: Tue Oct 23 14:35:05 2007 +0200
+ Signed-off-by: Stefan Roese <sr@denx.de>
- Fix a typo in cpu/mpc824x/interrupts.c
+commit 3048bcbf0bad262378c5af68f2bf6778fb7d829a
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 3 15:01:02 2007 +0200
- Since December 2003 the timer_interrupt_cpu() function in
- cpu/mpc824x/interrupts.c contains what seems to be a superfluous
- parameter. Remove it.
+ ppc4xx: Rename 405gp_pci to 4xx_pci since its used on all 4xx platforms
- Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
+ These files were introduced with the IBM 405GP but are currently used on all
+ 4xx PPC platforms. So the name doesn't match the content anymore. This patch
+ renames the files to 4xx_pci.c/h.
-commit c9e7b9b9a1700fe009678d1f9b41e6364ac5df2d
-Author: Sergej Stepanov <Sergej.Stepanov@ids.de>
-Date: Wed Oct 17 11:13:51 2007 +0200
+ Signed-off-by: Stefan Roese <sr@denx.de>
- add ft_cpu_setup(..) on mpc8260
+commit 94276eb0a7a35b9e8c053d589ae225b0f017a237
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 3 14:14:58 2007 +0200
- Add ft_cpu_setup(..)-function to adapt it for use with libfdt
- based on code from mpc5xxx
+ ppc4xx: Add a comment for 405EX PCIe endpoint configuration
- Sigend-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
- --
+ Signed-off-by: Stefan Roese <sr@denx.de>
-commit 6abd82e19ae93c0b4d104e50165e235915ec0875
-Author: Sergej Stepanov <Sergej.Stepanov@ids.de>
-Date: Wed Oct 17 11:18:42 2007 +0200
+commit 03d344bb6a5f082ea10ec9d753558ea7dfd1c626
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 3 10:38:09 2007 +0200
- changes for IDS8247 board support
+ ppc4xx: Make 440SPe PCIe code more generic to use on different 4xx PPCs (3)
- To get the IDS8247 board working following are done:
- - FCC2 is deactivated
- - FCC1 is activated
- - I2C is activated
- - CFI driver is activated
- - Adapted for use with LIBFDT
+ (3) This patch introduces macros like SDRN_PESDR_DLPSET(port) to access
+ the SDR registers of the PCIe ports. This makes the overall design
+ clearer, since it removed a lot of switch statements which are not
+ needed anymore.
- Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
- --
+ Also, the functions ppc4xx_init_pcie_rootport() and
+ ppc4xx_init_pcie_entport() are merged into a single function
+ ppc4xx_init_pcie_port(), since most of the code was duplicated.
+ This makes maintainance and porting to other 4xx platforms
+ easier.
-commit 8b6684a698500be9c142ec2c9f46cfc348e17f0c
-Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
-Date: Wed Oct 24 15:48:37 2007 +0200
+ Signed-off-by: Stefan Roese <sr@denx.de>
- ATSTK1002: Remove default ethernet addresses
+commit 026f71106871f31d17d0ea0db9a7547ff92934bc
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 3 07:48:09 2007 +0200
- Wolfgang is right: It's not a good idea to set up default initial
- ethernet addresses for a board, even though they belong to the local
- range.
+ ppc4xx: Make 440SPe PCIe code more generic to use on different 4xx PPCs (2)
- This will change the failure mode from "IT manager screams at you for
- using duplicate ethernet addresses" to a nice error message explaining
- that the ethernet address hasn't been set properly.
+ This patch is the first patch of a series to make the 440SPe PCIe code
+ usable on different 4xx PPC platforms. In preperation for the new 405EX
+ which is also equipped with PCIe interfaces.
- Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+ (2) This patch renames the functions from 440spe_ to 4xx_ with a
+ little additional cleanup
-commit e5c794e491a57d829b6d8733e2ed8368a2269abf
-Author: Justin Flammia <jflammia@savantav.com>
-Date: Mon Oct 29 17:40:35 2007 -0400
+ Signed-off-by: Stefan Roese <sr@denx.de>
- DHCP Client Fix
+commit c7c6da23028f146d912514b95aefa3da7cf37699
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Oct 3 07:34:10 2007 +0200
- This is a multi-part message in MIME format.
+ ppc4xx: Make 440SPe PCIe code more generic to use on different 4xx PPCs (1)
- commit e6e505eae94ed721e123e177489291fc4544b7b8
- Author: Justin Flammia <jflammia@savantav.com>
- Date: Mon Oct 29 17:19:03 2007 -0400
+ This patch is the first patch of a series to make the 440SPe PCIe code
+ usable on different 4xx PPC platforms. In preperation for the new 405EX
+ which is also equipped with PCIe interfaces.
- Found a bug in the way the DHCP Request packet is built, where the IP address
- that is offered by the server is bound to prematurely. This patch is a fix of
- that bug where the IP address offered by the DHCP server is not used until
- after the DHCP ACK from the server is received.
+ (1) This patch renames the files from 440spe_pcie to 4xx_pcie
- Signed-off-by: Justin Flammia <jflammia@savantav.com>
- Signed-off-by: Ben Warren <bwarren@qstreams.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
commit 31548249decf18a6b877a18436b6139dd483fe4a
Author: Justin Flammia <jflammia@savantav.com>
Signed-off-by: Stefan Roese <sr@denx.de>
+commit 3c89d75409eb26639d36dfa11d4ee3d8b962dc3c
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Tue Oct 16 15:27:43 2007 -0500
+
+ Initial mpc8610hpcd Makefile files.
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Signed-off-by: Mahesh Jade <mahesh.jade@freescale.com>
+ Signed-off-by: Jason Jin <Jason.jin@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 9553df86d3a319c3a1a7cde7e4edd6eeb5aa64c7
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Tue Oct 16 15:26:51 2007 -0500
+
+ Initial mpc8610hpcd cpu/, README and include/ files.
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Signed-off-by: Mahesh Jade <mahesh.jade@freescale.com>
+ Signed-off-by: Jason Jin <Jason.jin@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 3dd2db53ceb0dff80f25c2a07f83f29b907b403e
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Tue Oct 16 13:54:01 2007 -0500
+
+ Initial mpc8610hpcd board files.
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Signed-off-by: Mahesh Jade <mahesh.jade@freescale.com>
+ Signed-off-by: Jason Jin <Jason.jin@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
commit 7ee6ba1a056e4061ab4cfde30127e332e7957afd
Author: runet@innovsys.com <runet@innovsys.com>
Date: Tue Oct 16 14:50:40 2007 -0500
projects / oweals / u-boot.git / commitdiff