interrupt-controller;
#interrupt-cells = <1>;
+ ac_power_supply: ac-power-supply {
+ compatible = "x-powers,axp202-ac-power-supply";
+ status = "disabled";
+ };
+
+ axp_adc: adc {
+ compatible = "x-powers,axp209-adc";
+ #io-channel-cells = <1>;
+ };
+
axp_gpio: gpio {
compatible = "x-powers,axp209-gpio";
gpio-controller;
#gpio-cells = <2>;
};
+ battery_power_supply: battery-power-supply {
+ compatible = "x-powers,axp209-battery-power-supply";
+ status = "disabled";
+ };
+
regulators {
/* Default work frequency for buck regulators */
x-powers,dcdc-freq = <1500>;
};
};
- usb_power_supply: usb_power_supply {
+ usb_power_supply: usb-power-supply {
compatible = "x-powers,axp202-usb-power-supply";
status = "disabled";
};
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Mele A1000";
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_a1000>;
red {
label = "a1000:red:usr";
reg_emac_3v3: emac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&emac_power_pin_a1000>;
regulator-name = "emac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
status = "okay";
};
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
&ehci0 {
status = "okay";
};
};
&emac {
- pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pins>;
status = "okay";
};
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
status = "okay";
};
-&pio {
- emac_power_pin_a1000: emac_power_pin@0 {
- allwinner,pins = "PH15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
+#include "axp209.dtsi"
- led_pins_a1000: led_pins@0 {
- allwinner,pins = "PH10", "PH20";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
};
®_usb1_vbus {
&spdif {
pinctrl-names = "default";
- pinctrl-0 = <&spdif_tx_pins_a>;
+ pinctrl-0 = <&spdif_tx_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
};
&emac {
- pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pins>;
status = "okay";
};
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
status = "okay";
};
-&ohci1 {
- status = "okay";
-};
-
&otg_sram {
status = "okay";
};
-&pio {
- usb2_vbus_pin_a: usb2_vbus_pin@0 {
- allwinner,pins = "PH12";
- };
-};
-
®_usb0_vbus {
regulator-boot-on;
status = "okay";
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
ft5306de4: touchscreen@38 {
vref-supply = <®_vcc3v0>;
status = "okay";
- button@800 {
+ button-800 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <800000>;
};
- button@1000 {
+ button-1000 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <1000000>;
};
- button@1200 {
+ button-1200 {
label = "Back";
linux,code = <KEY_BACK>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
};
&pio {
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ usb0_id_detect_pin: usb0-id-detect-pin {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
};
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PH5";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ usb0_vbus_detect_pin: usb0-vbus-detect-pin {
+ pins = "PH5";
+ function = "gpio_in";
+ bias-pull-down;
};
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Cubietech Cubieboard";
stdout-path = "serial0:115200n8";
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
cpu-supply = <®_dcdc2>;
};
+&de {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
};
&emac {
- pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
status = "okay";
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pins>;
status = "okay";
};
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
};
&pio {
- led_pins_cubieboard: led_pins@0 {
- allwinner,pins = "PH20", "PH21";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_20_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ led_pins_cubieboard: led-pins {
+ pins = "PH20", "PH21";
+ function = "gpio_out";
+ drive-strength = <20>;
};
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ usb0_id_detect_pin: usb0-id-detect-pin {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
};
};
#include "axp209.dtsi"
+&ac_power_supply {
+ status = "okay";
+};
+
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
&spi0 {
pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins_a>,
- <&spi0_cs0_pins_a>;
+ pinctrl-0 = <&spi0_pi_pins>,
+ <&spi0_cs0_pi_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/pwm/pwm.h>
/ {
backlight: backlight {
compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&bl_en_pin_dsrv9703c>;
pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
default-brightness-level = <8>;
max-microvolt = <3000000>;
};
- reg_motor: reg_motor {
+ reg_motor: reg-motor {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&motor_pins>;
regulator-name = "vcc-motor";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
};
&codec {
- pinctrl-names = "default";
- pinctrl-0 = <&codec_pa_pin>;
allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
#include "axp209.dtsi"
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
/* pull-ups and devices require AXP209 LDO3 */
status = "failed";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
ft5406ee8: touchscreen@38 {
reg = <0x38>;
interrupt-parent = <&pio>;
interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
- pinctrl-names = "default";
- pinctrl-0 = <&touchscreen_pins>;
reset-gpios = <&pio 1 13 GPIO_ACTIVE_LOW>;
touchscreen-size-x = <1024>;
touchscreen-size-y = <768>;
vref-supply = <®_ldo2>;
status = "okay";
- button@400 {
+ button-400 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <400000>;
};
- button@800 {
+ button-800 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
};
&pio {
- bl_en_pin_dsrv9703c: bl_en_pin@0 {
- allwinner,pins = "PH7";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- codec_pa_pin: codec_pa_pin@0 {
- allwinner,pins = "PH15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- motor_pins: motor_pins@0 {
- allwinner,pins = "PB3";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- touchscreen_pins: touchscreen_pins@0 {
- allwinner,pins = "PB13";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ usb0_id_detect_pin: usb0-id-detect-pin {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
};
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PH5";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ usb0_vbus_detect_pin: usb0-vbus-detect-pin {
+ pins = "PH5";
+ function = "gpio_in";
+ bias-pull-down;
};
};
&pwm {
pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins_a>;
+ pinctrl-0 = <&pwm0_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
*/
&codec {
/* PH15 controls power to external amplifier (ft2012q) */
- pinctrl-names = "default";
- pinctrl-0 = <&codec_pa_pin>;
allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>;
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
#include "axp209.dtsi"
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
/* Accelerometer */
status = "okay";
- button@158 {
+ button-158 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <158730>;
};
- button@349 {
+ button-349 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <349206>;
};
- button@1142 {
+ button-1142 {
label = "Esc";
linux,code = <KEY_ESC>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH01 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH01 */
status = "okay";
};
-&pio {
- codec_pa_pin: codec_pa_pin@0 {
- allwinner,pins = "PH15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-};
-
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Miniand Hackberry";
};
&emac {
- pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_a>;
phy = <&phy0>;
status = "okay";
};
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pins>;
status = "okay";
};
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
status = "okay";
};
-&pio {
- pinctrl-names = "default";
- pinctrl-0 = <&hackberry_hogs>;
-
- hackberry_hogs: hogs@0 {
- allwinner,pins = "PH19";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb2_vbus_pin_hackberry: usb2_vbus_pin@0 {
- allwinner,pins = "PH12";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-};
-
®_usb1_vbus {
status = "okay";
};
®_usb2_vbus {
- pinctrl-0 = <&usb2_vbus_pin_hackberry>;
gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
};
&pio {
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ usb0_id_detect_pin: usb0-id-detect-pin {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
};
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PH5";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ usb0_vbus_detect_pin: usb0-vbus-detect-pin {
+ pins = "PH5";
+ function = "gpio_in";
+ bias-pull-down;
};
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
-&usb2_vbus_pin_a {
- allwinner,pins = "PH6";
-};
-
&usb_otg {
dr_mode = "otg";
status = "okay";
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/pwm/pwm.h>
/ {
backlight: backlight {
compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&bl_en_pin_inet>;
pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
default-brightness-level = <8>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
#include "axp209.dtsi"
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
/* Accelerometer */
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
ft5x: touchscreen@38 {
reg = <0x38>;
interrupt-parent = <&pio>;
interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
- pinctrl-names = "default";
- pinctrl-0 = <&touchscreen_wake_pin>;
wake-gpios = <&pio 1 13 GPIO_ACTIVE_HIGH>; /* PB13 */
touchscreen-size-x = <600>;
touchscreen-size-y = <1024>;
vref-supply = <®_ldo2>;
status = "okay";
- button@200 {
+ button-200 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <200000>;
};
- button@1000 {
+ button-1000 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <1000000>;
};
- button@1200 {
+ button-1200 {
label = "Home";
linux,code = <KEY_HOMEPAGE>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
};
&pio {
- bl_en_pin_inet: bl_en_pin@0 {
- allwinner,pins = "PH7";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- touchscreen_wake_pin: touchscreen_wake_pin@0 {
- allwinner,pins = "PB13";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ usb0_id_detect_pin: usb0-id-detect-pin {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
};
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PH5";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ usb0_vbus_detect_pin: usb0-vbus-detect-pin {
+ pins = "PH5";
+ function = "gpio_in";
+ bias-pull-down;
};
};
&pwm {
pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins_a>;
+ pinctrl-0 = <&pwm0_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
#include "axp209.dtsi"
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
ft5406ee8: touchscreen@38 {
vref-supply = <®_ldo2>;
status = "okay";
- button@200 {
+ button-200 {
label = "Menu";
linux,code = <KEY_MENU>;
channel = <0>;
voltage = <200000>;
};
- button@600 {
+ button-600 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <600000>;
};
- button@800 {
+ button-800 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <800000>;
};
- button@1000 {
+ button-1000 {
label = "Home";
linux,code = <KEY_HOMEPAGE>;
channel = <0>;
voltage = <1000000>;
};
- button@1200 {
+ button-1200 {
label = "Esc";
linux,code = <KEY_ESC>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
};
&pio {
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ usb0_id_detect_pin: usb0-id-detect-pin {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
};
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PH5";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ usb0_vbus_detect_pin: usb0-vbus-detect-pin {
+ pins = "PH5";
+ function = "gpio_in";
+ bias-pull-down;
};
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "iNet-9F Rev 03";
stdout-path = "serial0:115200n8";
};
- gpio_keys {
+ gpio-keys {
compatible = "gpio-keys-polled";
pinctrl-names = "default";
pinctrl-0 = <&key_pins_inet9f>;
#size-cells = <0>;
poll-interval = <20>;
- button@0 {
+ left-joystick-left {
label = "Left Joystick Left";
linux,code = <ABS_X>;
linux,input-type = <EV_ABS>;
gpios = <&pio 0 6 GPIO_ACTIVE_LOW>; /* PA6 */
};
- button@1 {
+ left-joystick-right {
label = "Left Joystick Right";
linux,code = <ABS_X>;
linux,input-type = <EV_ABS>;
gpios = <&pio 0 5 GPIO_ACTIVE_LOW>; /* PA5 */
};
- button@2 {
+ left-joystick-up {
label = "Left Joystick Up";
linux,code = <ABS_Y>;
linux,input-type = <EV_ABS>;
gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
};
- button@3 {
+ left-joystick-down {
label = "Left Joystick Down";
linux,code = <ABS_Y>;
linux,input-type = <EV_ABS>;
gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
};
- button@4 {
+ right-joystick-left {
label = "Right Joystick Left";
linux,code = <ABS_Z>;
linux,input-type = <EV_ABS>;
gpios = <&pio 0 1 GPIO_ACTIVE_LOW>; /* PA1 */
};
- button@5 {
+ right-joystick-right {
label = "Right Joystick Right";
linux,code = <ABS_Z>;
linux,input-type = <EV_ABS>;
gpios = <&pio 0 0 GPIO_ACTIVE_LOW>; /* PA0 */
};
- button@6 {
+ right-joystick-up {
label = "Right Joystick Up";
linux,code = <ABS_RZ>;
linux,input-type = <EV_ABS>;
gpios = <&pio 0 3 GPIO_ACTIVE_LOW>; /* PA3 */
};
- button@7 {
+ right-joystick-down {
label = "Right Joystick Down";
linux,code = <ABS_RZ>;
linux,input-type = <EV_ABS>;
gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */
};
- button@8 {
+ dpad-left {
label = "DPad Left";
linux,code = <ABS_HAT0X>;
linux,input-type = <EV_ABS>;
gpios = <&pio 7 23 GPIO_ACTIVE_LOW>; /* PH23 */
};
- button@9 {
+ dpad-right {
label = "DPad Right";
linux,code = <ABS_HAT0X>;
linux,input-type = <EV_ABS>;
gpios = <&pio 7 24 GPIO_ACTIVE_LOW>; /* PH24 */
};
- button@10 {
+ dpad-up {
label = "DPad Up";
linux,code = <ABS_HAT0Y>;
linux,input-type = <EV_ABS>;
gpios = <&pio 7 25 GPIO_ACTIVE_LOW>; /* PH25 */
};
- button@11 {
+ dpad-down {
label = "DPad Down";
linux,code = <ABS_HAT0Y>;
linux,input-type = <EV_ABS>;
gpios = <&pio 7 26 GPIO_ACTIVE_LOW>; /* PH26 */
};
- button@12 {
+ x {
label = "Button X";
linux,code = <BTN_X>;
gpios = <&pio 0 16 GPIO_ACTIVE_LOW>; /* PA16 */
};
- button@13 {
+ y {
label = "Button Y";
linux,code = <BTN_Y>;
gpios = <&pio 0 14 GPIO_ACTIVE_LOW>; /* PA14 */
};
- button@14 {
+ a {
label = "Button A";
linux,code = <BTN_A>;
gpios = <&pio 0 17 GPIO_ACTIVE_LOW>; /* PA17 */
};
- button@15 {
+ b {
label = "Button B";
linux,code = <BTN_B>;
gpios = <&pio 0 15 GPIO_ACTIVE_LOW>; /* PA15 */
};
- button@16 {
+ select {
label = "Select Button";
linux,code = <BTN_SELECT>;
gpios = <&pio 0 11 GPIO_ACTIVE_LOW>; /* PA11 */
};
- button@17 {
+ start {
label = "Start Button";
linux,code = <BTN_START>;
gpios = <&pio 0 12 GPIO_ACTIVE_LOW>; /* PA12 */
};
- button@18 {
+ top-left {
label = "Top Left Button";
linux,code = <BTN_TL>;
gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */
};
- button@19 {
+ top-right {
label = "Top Right Button";
linux,code = <BTN_TR>;
gpios = <&pio 0 13 GPIO_ACTIVE_LOW>; /* PA13 */
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
#include "axp209.dtsi"
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
/* Accelerometer */
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
ft5406ee8: touchscreen@38 {
vref-supply = <®_ldo2>;
status = "okay";
- button@200 {
+ button-200 {
label = "Menu";
linux,code = <KEY_MENU>;
channel = <0>;
voltage = <200000>;
};
- button@600 {
+ button-600 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <600000>;
};
- button@800 {
+ button-800 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <800000>;
};
- button@1000 {
+ button-1000 {
label = "Home";
linux,code = <KEY_HOMEPAGE>;
channel = <0>;
voltage = <1000000>;
};
- button@1200 {
+ button-1200 {
label = "Esc";
linux,code = <KEY_ESC>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
};
&pio {
- key_pins_inet9f: key_pins@0 {
- allwinner,pins = "PA0", "PA1", "PA3", "PA4",
- "PA5", "PA6", "PA8", "PA9",
- "PA11", "PA12", "PA13",
- "PA14", "PA15", "PA16", "PA17",
- "PH22", "PH23", "PH24", "PH25", "PH26";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ key_pins_inet9f: key-pins {
+ pins = "PA0", "PA1", "PA3", "PA4",
+ "PA5", "PA6", "PA8", "PA9",
+ "PA11", "PA12", "PA13",
+ "PA14", "PA15", "PA16", "PA17",
+ "PH22", "PH23", "PH24", "PH25", "PH26";
+ function = "gpio_in";
+ bias-pull-up;
};
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ usb0_id_detect_pin: usb0-id-detect-pin {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
};
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PH5";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ usb0_vbus_detect_pin: usb0-vbus-detect-pin {
+ pins = "PH5";
+ function = "gpio_in";
+ bias-pull-down;
};
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&emac {
pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_a>;
+ pinctrl-0 = <&emac_pins>;
phy = <&phy1>;
status = "okay";
};
};
&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
axp209: pmic@34 {
interrupts = <0>;
};
&i2c1 {
pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
+ pinctrl-0 = <&i2c1_pins>;
status = "okay";
};
&i2c2 {
pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
+ pinctrl-0 = <&i2c2_pins>;
status = "okay";
};
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pins>;
status = "okay";
};
&mmc0 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
&spi0 {
pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins_a>,
- <&spi0_cs0_pins_a>;
+ pinctrl-0 = <&spi0_pi_pins>,
+ <&spi0_cs0_pi_pin>;
status = "okay";
};
+
+&uart0 {
+ pinctrl-0 = <&uart0_pb_pins>;
+};
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Jesurun Q5";
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_q5>;
green {
label = "q5:green:usr";
reg_emac_3v3: emac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&emac_power_pin_q5>;
regulator-name = "emac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
&emac {
- pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pins>;
status = "okay";
};
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
status = "okay";
};
-&pio {
- emac_power_pin_q5: emac_power_pin@0 {
- allwinner,pins = "PH19";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- led_pins_q5: led_pins@0 {
- allwinner,pins = "PH20";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-};
-
®_usb0_vbus {
regulator-boot-on;
status = "okay";
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "HAOYU Electronics Marsboard A10";
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_marsboard>;
red1 {
label = "marsboard:red1:usr";
};
&emac {
- pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
};
&pio {
- led_pins_marsboard: led_pins@0 {
- allwinner,pins = "PB5", "PB6", "PB7", "PB8";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ usb0_id_detect_pin: usb0-id-detect-pin {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
};
};
&spi0 {
pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins_a>,
- <&spi0_cs0_pins_a>;
+ pinctrl-0 = <&spi0_pi_pins>,
+ <&spi0_cs0_pi_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "PineRiver Mini X-Plus";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pins>;
status = "okay";
};
-&ir0_rx_pins_a {
+&ir0_rx_pins {
/* The ir receiver is not always populated */
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ bias-pull-up;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
#include "sun4i-a10.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "MK802";
chosen {
stdout-path = "serial0:115200n8";
};
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
};
&codec {
status = "okay";
};
+&de {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
status = "okay";
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
status = "okay";
};
-&pio {
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PH5";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb2_vbus_pin_mk802: usb2_vbus_pin@0 {
- allwinner,pins = "PH12";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-};
-
®_usb0_vbus {
status = "okay";
};
};
®_usb2_vbus {
- pinctrl-0 = <&usb2_vbus_pin_mk802>;
gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
usb0_vbus-supply = <®_usb0_vbus>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Olimex A10-OLinuXino-LIME";
stdout-path = "serial0:115200n8";
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
864000 1300000
624000 1250000
>;
- cooling-max-level = <2>;
+};
+
+&de {
+ status = "okay";
};
&ehci0 {
};
&emac {
- pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
status = "okay";
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
eeprom: eeprom@50 {
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
};
&pio {
- ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 {
- allwinner,pins = "PC3";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- led_pins_olinuxinolime: led_pins@0 {
- allwinner,pins = "PH2";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_20_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ led_pins_olinuxinolime: led-pin {
+ pins = "PH2";
+ function = "gpio_out";
+ drive-strength = <20>;
};
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ usb0_id_detect_pin: usb0-id-detect-pin {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
};
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PH5";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ usb0_vbus_detect_pin: usb0-vbus-detect-pin {
+ pins = "PH5";
+ function = "gpio_in";
+ bias-pull-down;
};
};
®_ahci_5v {
- pinctrl-0 = <&ahci_pwr_pin_olinuxinolime>;
gpio = <&pio 2 3 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "LinkSprite pcDuino";
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_pcduino>;
tx {
label = "pcduino:green:tx";
};
};
- gpio_keys {
+ gpio-keys {
compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&key_pins_pcduino>;
#address-cells = <1>;
#size-cells = <0>;
- button@0 {
+ back {
label = "Key Back";
linux,code = <KEY_BACK>;
gpios = <&pio 7 17 GPIO_ACTIVE_LOW>;
};
- button@1 {
+ home {
label = "Key Home";
linux,code = <KEY_HOME>;
gpios = <&pio 7 18 GPIO_ACTIVE_LOW>;
};
- button@2 {
+ menu {
label = "Key Menu";
linux,code = <KEY_MENU>;
gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
};
&emac {
- pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
};
&pio {
- led_pins_pcduino: led_pins@0 {
- allwinner,pins = "PH15", "PH16";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- key_pins_pcduino: key_pins@0 {
- allwinner,pins = "PH17", "PH18", "PH19";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ usb0_id_detect_pin: usb0-id-detect-pin {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
};
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
compatible = "linksprite,a10-pcduino2", "allwinner,sun4i-a10";
};
-&pio {
- usb2_vbus_pin_pcduino2: usb2_vbus_pin@0 {
- allwinner,pins = "PD2";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-};
-
®_usb2_vbus {
- pinctrl-names = "default";
- pinctrl-0 = <&usb2_vbus_pin_pcduino2>;
gpio = <&pio 3 2 GPIO_ACTIVE_HIGH>;
status = "okay";
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/pwm/pwm.h>
/ {
backlight: backlight {
compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&bl_en_pin_protab>;
pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
default-brightness-level = <8>;
};
&codec {
- pinctrl-names = "default";
- pinctrl-0 = <&codec_pa_pin>;
allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
#include "axp209.dtsi"
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
-
- /* Accelerometer */
- bma250@18 {
- compatible = "bosch,bma250";
- reg = <0x18>;
- interrupt-parent = <&pio>;
- interrupts = <7 0 IRQ_TYPE_EDGE_RISING>; /* PH0 / EINT0 */
- };
+ /* pull-ups and devices require AXP209 LDO3 */
+ status = "failed";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
- pixcir_ts@5c {
- pinctrl-names = "default";
- pinctrl-0 = <&touchscreen_pins>;
+ touchscreen@5c {
compatible = "pixcir,pixcir_tangoc";
reg = <0x5c>;
interrupt-parent = <&pio>;
vref-supply = <®_ldo2>;
status = "okay";
- button@400 {
+ button-400 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <400000>;
};
- button@800 {
+ button-800 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
};
&pio {
- bl_en_pin_protab: bl_en_pin@0 {
- allwinner,pins = "PH7";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ usb0_id_detect_pin: usb0-id-detect-pin {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
};
- codec_pa_pin: codec_pa_pin@0 {
- allwinner,pins = "PH15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- touchscreen_pins: touchscreen_pins@0 {
- allwinner,pins = "PA5", "PB13";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PH5";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ usb0_vbus_detect_pin: usb0-vbus-detect-pin {
+ pins = "PH5";
+ function = "gpio_in";
+ bias-pull-down;
};
};
&pwm {
pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins_a>;
+ pinctrl-0 = <&pwm0_pin>;
status = "okay";
};
regulator-name = "avcc";
};
-®_ldo3 {
- /*
- * We need to always power the camera sensor, otherwhise all access
- * to i2c1 is blocked.
- */
- regulator-always-on;
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-name = "vdd-csi";
-};
-
®_usb0_vbus {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/thermal/thermal.h>
-
-#include <dt-bindings/clock/sun4i-a10-pll2.h>
#include <dt-bindings/dma/sun4i-a10.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/clock/sun4i-a10-ccu.h>
+#include <dt-bindings/reset/sun4i-a10-ccu.h>
/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
interrupt-parent = <&intc>;
aliases {
#size-cells = <1>;
ranges;
- framebuffer@0 {
+ framebuffer-lcd0-hdmi {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
- clocks = <&ahb_gates 36>, <&ahb_gates 43>,
- <&ahb_gates 44>, <&de_be0_clk>,
- <&tcon0_ch1_clk>, <&dram_gates 26>;
+ clocks = <&ccu CLK_AHB_LCD0>, <&ccu CLK_AHB_HDMI0>,
+ <&ccu CLK_AHB_DE_BE0>, <&ccu CLK_DE_BE0>,
+ <&ccu CLK_TCON0_CH1>, <&ccu CLK_DRAM_DE_BE0>;
status = "disabled";
};
- framebuffer@1 {
+ framebuffer-fe0-lcd0-hdmi {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_fe0-de_be0-lcd0-hdmi";
- clocks = <&ahb_gates 36>, <&ahb_gates 43>,
- <&ahb_gates 44>, <&ahb_gates 46>,
- <&de_be0_clk>, <&de_fe0_clk>, <&tcon0_ch1_clk>,
- <&dram_gates 25>, <&dram_gates 26>;
+ clocks = <&ccu CLK_AHB_LCD0>, <&ccu CLK_AHB_HDMI0>,
+ <&ccu CLK_AHB_DE_BE0>, <&ccu CLK_AHB_DE_FE0>,
+ <&ccu CLK_DE_BE0>, <&ccu CLK_DE_FE0>,
+ <&ccu CLK_TCON0_CH1>, <&ccu CLK_HDMI>,
+ <&ccu CLK_DRAM_DE_FE0>, <&ccu CLK_DRAM_DE_BE0>;
status = "disabled";
};
- framebuffer@2 {
+ framebuffer-fe0-lcd0 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_fe0-de_be0-lcd0";
- clocks = <&ahb_gates 36>, <&ahb_gates 44>, <&ahb_gates 46>,
- <&de_be0_clk>, <&de_fe0_clk>, <&tcon0_ch0_clk>,
- <&dram_gates 25>, <&dram_gates 26>;
+ clocks = <&ccu CLK_AHB_LCD0>, <&ccu CLK_AHB_DE_BE0>,
+ <&ccu CLK_AHB_DE_FE0>, <&ccu CLK_DE_BE0>,
+ <&ccu CLK_DE_FE0>, <&ccu CLK_TCON0_CH0>,
+ <&ccu CLK_DRAM_DE_FE0>, <&ccu CLK_DRAM_DE_BE0>;
status = "disabled";
};
- framebuffer@3 {
+ framebuffer-fe0-lcd0-tve0 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_fe0-de_be0-lcd0-tve0";
- clocks = <&ahb_gates 34>, <&ahb_gates 36>,
- <&ahb_gates 44>, <&ahb_gates 46>,
- <&de_be0_clk>, <&de_fe0_clk>,
- <&tcon0_ch1_clk>, <&dram_gates 5>,
- <&dram_gates 25>, <&dram_gates 26>;
+ clocks = <&ccu CLK_AHB_TVE0>, <&ccu CLK_AHB_LCD0>,
+ <&ccu CLK_AHB_DE_BE0>, <&ccu CLK_AHB_DE_FE0>,
+ <&ccu CLK_DE_BE0>, <&ccu CLK_DE_FE0>,
+ <&ccu CLK_TCON0_CH1>, <&ccu CLK_DRAM_TVE0>,
+ <&ccu CLK_DRAM_DE_FE0>, <&ccu CLK_DRAM_DE_BE0>;
status = "disabled";
};
};
device_type = "cpu";
compatible = "arm,cortex-a8";
reg = <0x0>;
- clocks = <&cpu>;
+ clocks = <&ccu CLK_CPU>;
clock-latency = <244144>; /* 8 32k periods */
operating-points = <
/* kHz uV */
624000 1250000
>;
#cooling-cells = <2>;
- cooling-min-level = <0>;
- cooling-max-level = <3>;
};
};
thermal-zones {
- cpu_thermal {
+ cpu-thermal {
/* milliseconds */
polling-delay-passive = <250>;
polling-delay = <1000>;
};
trips {
- cpu_alert0: cpu_alert0 {
+ cpu_alert0: cpu-alert0 {
/* milliCelsius */
temperature = <850000>;
hysteresis = <2000>;
type = "passive";
};
- cpu_crit: cpu_crit {
+ cpu_crit: cpu-crit {
/* milliCelsius */
temperature = <100000>;
hysteresis = <2000>;
};
};
- memory {
- reg = <0x40000000 0x80000000>;
- };
-
clocks {
#address-cells = <1>;
#size-cells = <1>;
ranges;
- /*
- * This is a dummy clock, to be used as placeholder on
- * other mux clocks when a specific parent clock is not
- * yet implemented. It should be dropped when the driver
- * is complete.
- */
- dummy: dummy {
+ osc24M: clk-24M {
#clock-cells = <0>;
compatible = "fixed-clock";
- clock-frequency = <0>;
- };
-
- osc24M: clk@01c20050 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-osc-clk";
- reg = <0x01c20050 0x4>;
clock-frequency = <24000000>;
clock-output-names = "osc24M";
};
- osc3M: osc3M_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <8>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "osc3M";
- };
-
- osc32k: clk@0 {
+ osc32k: clk-32k {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
clock-output-names = "osc32k";
};
+ };
- pll1: clk@01c20000 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll1-clk";
- reg = <0x01c20000 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll1";
- };
-
- pll2: clk@01c20008 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-pll2-clk";
- reg = <0x01c20008 0x8>;
- clocks = <&osc24M>;
- clock-output-names = "pll2-1x", "pll2-2x",
- "pll2-4x", "pll2-8x";
- };
-
- pll3: clk@01c20010 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll3-clk";
- reg = <0x01c20010 0x4>;
- clocks = <&osc3M>;
- clock-output-names = "pll3";
- };
-
- pll3x2: pll3x2_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <2>;
- clocks = <&pll3>;
- clock-output-names = "pll3-2x";
- };
-
- pll4: clk@01c20018 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll1-clk";
- reg = <0x01c20018 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll4";
- };
-
- pll5: clk@01c20020 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-pll5-clk";
- reg = <0x01c20020 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll5_ddr", "pll5_other";
- };
-
- pll6: clk@01c20028 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-pll6-clk";
- reg = <0x01c20028 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll6_sata", "pll6_other", "pll6";
- };
-
- pll7: clk@01c20030 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll3-clk";
- reg = <0x01c20030 0x4>;
- clocks = <&osc3M>;
- clock-output-names = "pll7";
- };
-
- pll7x2: pll7x2_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <2>;
- clocks = <&pll7>;
- clock-output-names = "pll7-2x";
- };
-
- /* dummy is 200M */
- cpu: cpu@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-cpu-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>;
- clock-output-names = "cpu";
- };
-
- axi: axi@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-axi-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&cpu>;
- clock-output-names = "axi";
- };
-
- axi_gates: clk@01c2005c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-axi-gates-clk";
- reg = <0x01c2005c 0x4>;
- clocks = <&axi>;
- clock-indices = <0>;
- clock-output-names = "axi_dram";
- };
-
- ahb: ahb@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-ahb-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&axi>;
- clock-output-names = "ahb";
- };
-
- ahb_gates: clk@01c20060 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-ahb-gates-clk";
- reg = <0x01c20060 0x8>;
- clocks = <&ahb>;
- clock-indices = <0>, <1>,
- <2>, <3>,
- <4>, <5>, <6>,
- <7>, <8>, <9>,
- <10>, <11>, <12>,
- <13>, <14>, <16>,
- <17>, <18>, <20>,
- <21>, <22>, <23>,
- <24>, <25>, <26>,
- <32>, <33>, <34>,
- <35>, <36>, <37>,
- <40>, <41>, <43>,
- <44>, <45>,
- <46>, <47>,
- <50>, <52>;
- clock-output-names = "ahb_usb0", "ahb_ehci0",
- "ahb_ohci0", "ahb_ehci1",
- "ahb_ohci1", "ahb_ss", "ahb_dma",
- "ahb_bist", "ahb_mmc0", "ahb_mmc1",
- "ahb_mmc2", "ahb_mmc3", "ahb_ms",
- "ahb_nand", "ahb_sdram", "ahb_ace",
- "ahb_emac", "ahb_ts", "ahb_spi0",
- "ahb_spi1", "ahb_spi2", "ahb_spi3",
- "ahb_pata", "ahb_sata", "ahb_gps",
- "ahb_ve", "ahb_tvd", "ahb_tve0",
- "ahb_tve1", "ahb_lcd0", "ahb_lcd1",
- "ahb_csi0", "ahb_csi1", "ahb_hdmi",
- "ahb_de_be0", "ahb_de_be1",
- "ahb_de_fe0", "ahb_de_fe1",
- "ahb_mp", "ahb_mali400";
- };
-
- apb0: apb0@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb0-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&ahb>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk@01c20068 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-apb0-gates-clk";
- reg = <0x01c20068 0x4>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>,
- <2>, <3>,
- <5>, <6>,
- <7>, <10>;
- clock-output-names = "apb0_codec", "apb0_spdif",
- "apb0_ac97", "apb0_iis",
- "apb0_pio", "apb0_ir0",
- "apb0_ir1", "apb0_keypad";
- };
-
- apb1: clk@01c20058 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb1-clk";
- reg = <0x01c20058 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&osc32k>;
- clock-output-names = "apb1";
- };
-
- apb1_gates: clk@01c2006c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-apb1-gates-clk";
- reg = <0x01c2006c 0x4>;
- clocks = <&apb1>;
- clock-indices = <0>, <1>,
- <2>, <4>,
- <5>, <6>,
- <7>, <16>,
- <17>, <18>,
- <19>, <20>,
- <21>, <22>,
- <23>;
- clock-output-names = "apb1_i2c0", "apb1_i2c1",
- "apb1_i2c2", "apb1_can",
- "apb1_scr", "apb1_ps20",
- "apb1_ps21", "apb1_uart0",
- "apb1_uart1", "apb1_uart2",
- "apb1_uart3", "apb1_uart4",
- "apb1_uart5", "apb1_uart6",
- "apb1_uart7";
- };
-
- nand_clk: clk@01c20080 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20080 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "nand";
- };
-
- ms_clk: clk@01c20084 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20084 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ms";
- };
-
- mmc0_clk: clk@01c20088 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20088 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc0",
- "mmc0_output",
- "mmc0_sample";
- };
-
- mmc1_clk: clk@01c2008c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c2008c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc1",
- "mmc1_output",
- "mmc1_sample";
- };
-
- mmc2_clk: clk@01c20090 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20090 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc2",
- "mmc2_output",
- "mmc2_sample";
- };
-
- mmc3_clk: clk@01c20094 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20094 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc3",
- "mmc3_output",
- "mmc3_sample";
- };
-
- ts_clk: clk@01c20098 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20098 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ts";
- };
-
- ss_clk: clk@01c2009c {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c2009c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ss";
- };
-
- spi0_clk: clk@01c200a0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a0 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi0";
- };
-
- spi1_clk: clk@01c200a4 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a4 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi1";
- };
-
- spi2_clk: clk@01c200a8 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a8 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi2";
- };
-
- pata_clk: clk@01c200ac {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200ac 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "pata";
- };
-
- ir0_clk: clk@01c200b0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200b0 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ir0";
- };
-
- ir1_clk: clk@01c200b4 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200b4 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ir1";
- };
-
- spdif_clk: clk@01c200c0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod1-clk";
- reg = <0x01c200c0 0x4>;
- clocks = <&pll2 SUN4I_A10_PLL2_8X>,
- <&pll2 SUN4I_A10_PLL2_4X>,
- <&pll2 SUN4I_A10_PLL2_2X>,
- <&pll2 SUN4I_A10_PLL2_1X>;
- clock-output-names = "spdif";
- };
-
- usb_clk: clk@01c200cc {
- #clock-cells = <1>;
- #reset-cells = <1>;
- compatible = "allwinner,sun4i-a10-usb-clk";
- reg = <0x01c200cc 0x4>;
- clocks = <&pll6 1>;
- clock-output-names = "usb_ohci0", "usb_ohci1",
- "usb_phy";
- };
-
- spi3_clk: clk@01c200d4 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200d4 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi3";
- };
-
- dram_gates: clk@01c20100 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-dram-gates-clk";
- reg = <0x01c20100 0x4>;
- clocks = <&pll5 0>;
- clock-indices = <0>,
- <1>, <2>,
- <3>,
- <4>,
- <5>, <6>,
- <15>,
- <24>, <25>,
- <26>, <27>,
- <28>, <29>;
- clock-output-names = "dram_ve",
- "dram_csi0", "dram_csi1",
- "dram_ts",
- "dram_tvd",
- "dram_tve0", "dram_tve1",
- "dram_output",
- "dram_de_fe1", "dram_de_fe0",
- "dram_de_be0", "dram_de_be1",
- "dram_de_mp", "dram_ace";
- };
-
- de_be0_clk: clk@01c20104 {
- #clock-cells = <0>;
- #reset-cells = <0>;
- compatible = "allwinner,sun4i-a10-display-clk";
- reg = <0x01c20104 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll5 1>;
- clock-output-names = "de-be0";
- };
-
- de_be1_clk: clk@01c20108 {
- #clock-cells = <0>;
- #reset-cells = <0>;
- compatible = "allwinner,sun4i-a10-display-clk";
- reg = <0x01c20108 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll5 1>;
- clock-output-names = "de-be1";
- };
-
- de_fe0_clk: clk@01c2010c {
- #clock-cells = <0>;
- #reset-cells = <0>;
- compatible = "allwinner,sun4i-a10-display-clk";
- reg = <0x01c2010c 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll5 1>;
- clock-output-names = "de-fe0";
- };
-
- de_fe1_clk: clk@01c20110 {
- #clock-cells = <0>;
- #reset-cells = <0>;
- compatible = "allwinner,sun4i-a10-display-clk";
- reg = <0x01c20110 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll5 1>;
- clock-output-names = "de-fe1";
- };
-
-
- tcon0_ch0_clk: clk@01c20118 {
- #clock-cells = <0>;
- #reset-cells = <1>;
- compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
- reg = <0x01c20118 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
- clock-output-names = "tcon0-ch0-sclk";
-
- };
-
- tcon1_ch0_clk: clk@01c2011c {
- #clock-cells = <0>;
- #reset-cells = <1>;
- compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
- reg = <0x01c2011c 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
- clock-output-names = "tcon1-ch0-sclk";
-
- };
-
- tcon0_ch1_clk: clk@01c2012c {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
- reg = <0x01c2012c 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
- clock-output-names = "tcon0-ch1-sclk";
-
- };
-
- tcon1_ch1_clk: clk@01c20130 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
- reg = <0x01c20130 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
- clock-output-names = "tcon1-ch1-sclk";
-
- };
-
- ve_clk: clk@01c2013c {
- #clock-cells = <0>;
- #reset-cells = <0>;
- compatible = "allwinner,sun4i-a10-ve-clk";
- reg = <0x01c2013c 0x4>;
- clocks = <&pll4>;
- clock-output-names = "ve";
- };
-
- codec_clk: clk@01c20140 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-codec-clk";
- reg = <0x01c20140 0x4>;
- clocks = <&pll2 SUN4I_A10_PLL2_1X>;
- clock-output-names = "codec";
- };
+ de: display-engine {
+ compatible = "allwinner,sun4i-a10-display-engine";
+ allwinner,pipelines = <&fe0>, <&fe1>;
+ status = "disabled";
};
- soc@01c00000 {
+ soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
- sram-controller@01c00000 {
+ sram-controller@1c00000 {
compatible = "allwinner,sun4i-a10-sram-controller";
reg = <0x01c00000 0x30>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
- sram_a: sram@00000000 {
+ sram_a: sram@0 {
compatible = "mmio-sram";
reg = <0x00000000 0xc000>;
#address-cells = <1>;
};
};
- sram_d: sram@00010000 {
+ sram_d: sram@10000 {
compatible = "mmio-sram";
reg = <0x00010000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x00010000 0x1000>;
- otg_sram: sram-section@0000 {
+ otg_sram: sram-section@0 {
compatible = "allwinner,sun4i-a10-sram-d";
reg = <0x0000 0x1000>;
status = "disabled";
};
};
- dma: dma-controller@01c02000 {
+ dma: dma-controller@1c02000 {
compatible = "allwinner,sun4i-a10-dma";
reg = <0x01c02000 0x1000>;
interrupts = <27>;
- clocks = <&ahb_gates 6>;
+ clocks = <&ccu CLK_AHB_DMA>;
#dma-cells = <2>;
};
- nfc: nand@01c03000 {
+ nfc: nand@1c03000 {
compatible = "allwinner,sun4i-a10-nand";
reg = <0x01c03000 0x1000>;
interrupts = <37>;
- clocks = <&ahb_gates 13>, <&nand_clk>;
+ clocks = <&ccu CLK_AHB_NAND>, <&ccu CLK_NAND>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 3>;
dma-names = "rxtx";
#size-cells = <0>;
};
- spi0: spi@01c05000 {
+ spi0: spi@1c05000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c05000 0x1000>;
interrupts = <10>;
- clocks = <&ahb_gates 20>, <&spi0_clk>;
+ clocks = <&ccu CLK_AHB_SPI0>, <&ccu CLK_SPI0>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 27>,
<&dma SUN4I_DMA_DEDICATED 26>;
#size-cells = <0>;
};
- spi1: spi@01c06000 {
+ spi1: spi@1c06000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c06000 0x1000>;
interrupts = <11>;
- clocks = <&ahb_gates 21>, <&spi1_clk>;
+ clocks = <&ccu CLK_AHB_SPI1>, <&ccu CLK_SPI1>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 9>,
<&dma SUN4I_DMA_DEDICATED 8>;
dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>, <&spi1_cs0_pin>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- emac: ethernet@01c0b000 {
+ emac: ethernet@1c0b000 {
compatible = "allwinner,sun4i-a10-emac";
reg = <0x01c0b000 0x1000>;
interrupts = <55>;
- clocks = <&ahb_gates 17>;
+ clocks = <&ccu CLK_AHB_EMAC>;
allwinner,sram = <&emac_sram 1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_pins>;
status = "disabled";
};
- mdio: mdio@01c0b080 {
+ mdio: mdio@1c0b080 {
compatible = "allwinner,sun4i-a10-mdio";
reg = <0x01c0b080 0x14>;
status = "disabled";
#size-cells = <0>;
};
- mmc0: mmc@01c0f000 {
+ tcon0: lcd-controller@1c0c000 {
+ compatible = "allwinner,sun4i-a10-tcon";
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <44>;
+ resets = <&ccu RST_TCON0>;
+ reset-names = "lcd";
+ clocks = <&ccu CLK_AHB_LCD0>,
+ <&ccu CLK_TCON0_CH0>,
+ <&ccu CLK_TCON0_CH1>;
+ clock-names = "ahb",
+ "tcon-ch0",
+ "tcon-ch1";
+ clock-output-names = "tcon0-pixel-clock";
+ dmas = <&dma SUN4I_DMA_DEDICATED 14>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ tcon0_in_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_out_tcon0>;
+ };
+
+ tcon0_in_be1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&be1_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ tcon0_out_hdmi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&hdmi_in_tcon0>;
+ allwinner,tcon-channel = <1>;
+ };
+ };
+ };
+ };
+
+ tcon1: lcd-controller@1c0d000 {
+ compatible = "allwinner,sun4i-a10-tcon";
+ reg = <0x01c0d000 0x1000>;
+ interrupts = <45>;
+ resets = <&ccu RST_TCON1>;
+ reset-names = "lcd";
+ clocks = <&ccu CLK_AHB_LCD1>,
+ <&ccu CLK_TCON1_CH0>,
+ <&ccu CLK_TCON1_CH1>;
+ clock-names = "ahb",
+ "tcon-ch0",
+ "tcon-ch1";
+ clock-output-names = "tcon1-pixel-clock";
+ dmas = <&dma SUN4I_DMA_DEDICATED 15>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon1_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ tcon1_in_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_out_tcon1>;
+ };
+
+ tcon1_in_be1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&be1_out_tcon1>;
+ };
+ };
+
+ tcon1_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ tcon1_out_hdmi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&hdmi_in_tcon1>;
+ allwinner,tcon-channel = <1>;
+ };
+ };
+ };
+ };
+
+ mmc0: mmc@1c0f000 {
compatible = "allwinner,sun4i-a10-mmc";
reg = <0x01c0f000 0x1000>;
- clocks = <&ahb_gates 8>,
- <&mmc0_clk 0>,
- <&mmc0_clk 1>,
- <&mmc0_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
+ clocks = <&ccu CLK_AHB_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
interrupts = <32>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- mmc1: mmc@01c10000 {
+ mmc1: mmc@1c10000 {
compatible = "allwinner,sun4i-a10-mmc";
reg = <0x01c10000 0x1000>;
- clocks = <&ahb_gates 9>,
- <&mmc1_clk 0>,
- <&mmc1_clk 1>,
- <&mmc1_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
+ clocks = <&ccu CLK_AHB_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
interrupts = <33>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- mmc2: mmc@01c11000 {
+ mmc2: mmc@1c11000 {
compatible = "allwinner,sun4i-a10-mmc";
reg = <0x01c11000 0x1000>;
- clocks = <&ahb_gates 10>,
- <&mmc2_clk 0>,
- <&mmc2_clk 1>,
- <&mmc2_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
+ clocks = <&ccu CLK_AHB_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
interrupts = <34>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- mmc3: mmc@01c12000 {
+ mmc3: mmc@1c12000 {
compatible = "allwinner,sun4i-a10-mmc";
reg = <0x01c12000 0x1000>;
- clocks = <&ahb_gates 11>,
- <&mmc3_clk 0>,
- <&mmc3_clk 1>,
- <&mmc3_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
+ clocks = <&ccu CLK_AHB_MMC3>, <&ccu CLK_MMC3>;
+ clock-names = "ahb", "mmc";
interrupts = <35>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- usb_otg: usb@01c13000 {
+ usb_otg: usb@1c13000 {
compatible = "allwinner,sun4i-a10-musb";
reg = <0x01c13000 0x0400>;
- clocks = <&ahb_gates 0>;
+ clocks = <&ccu CLK_AHB_OTG>;
interrupts = <38>;
interrupt-names = "mc";
phys = <&usbphy 0>;
status = "disabled";
};
- usbphy: phy@01c13400 {
+ usbphy: phy@1c13400 {
#phy-cells = <1>;
compatible = "allwinner,sun4i-a10-usb-phy";
reg = <0x01c13400 0x10 0x01c14800 0x4 0x01c1c800 0x4>;
reg-names = "phy_ctrl", "pmu1", "pmu2";
- clocks = <&usb_clk 8>;
+ clocks = <&ccu CLK_USB_PHY>;
clock-names = "usb_phy";
- resets = <&usb_clk 0>, <&usb_clk 1>, <&usb_clk 2>;
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_PHY2>;
reset-names = "usb0_reset", "usb1_reset", "usb2_reset";
status = "disabled";
};
- ehci0: usb@01c14000 {
+ ehci0: usb@1c14000 {
compatible = "allwinner,sun4i-a10-ehci", "generic-ehci";
reg = <0x01c14000 0x100>;
interrupts = <39>;
- clocks = <&ahb_gates 1>;
+ clocks = <&ccu CLK_AHB_EHCI0>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
};
- ohci0: usb@01c14400 {
+ ohci0: usb@1c14400 {
compatible = "allwinner,sun4i-a10-ohci", "generic-ohci";
reg = <0x01c14400 0x100>;
interrupts = <64>;
- clocks = <&usb_clk 6>, <&ahb_gates 2>;
+ clocks = <&ccu CLK_USB_OHCI0>, <&ccu CLK_AHB_OHCI0>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
};
- crypto: crypto-engine@01c15000 {
+ crypto: crypto-engine@1c15000 {
compatible = "allwinner,sun4i-a10-crypto";
reg = <0x01c15000 0x1000>;
interrupts = <86>;
- clocks = <&ahb_gates 5>, <&ss_clk>;
+ clocks = <&ccu CLK_AHB_SS>, <&ccu CLK_SS>;
clock-names = "ahb", "mod";
};
- spi2: spi@01c17000 {
+ hdmi: hdmi@1c16000 {
+ compatible = "allwinner,sun4i-a10-hdmi";
+ reg = <0x01c16000 0x1000>;
+ interrupts = <58>;
+ clocks = <&ccu CLK_AHB_HDMI0>, <&ccu CLK_HDMI>,
+ <&ccu CLK_PLL_VIDEO0_2X>,
+ <&ccu CLK_PLL_VIDEO1_2X>;
+ clock-names = "ahb", "mod", "pll-0", "pll-1";
+ dmas = <&dma SUN4I_DMA_NORMAL 16>,
+ <&dma SUN4I_DMA_NORMAL 16>,
+ <&dma SUN4I_DMA_DEDICATED 24>;
+ dma-names = "ddc-tx", "ddc-rx", "audio-tx";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hdmi_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ hdmi_in_tcon0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_out_hdmi>;
+ };
+
+ hdmi_in_tcon1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&tcon1_out_hdmi>;
+ };
+ };
+
+ hdmi_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+ };
+
+ spi2: spi@1c17000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c17000 0x1000>;
interrupts = <12>;
- clocks = <&ahb_gates 22>, <&spi2_clk>;
+ clocks = <&ccu CLK_AHB_SPI2>, <&ccu CLK_SPI2>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 29>,
<&dma SUN4I_DMA_DEDICATED 28>;
#size-cells = <0>;
};
- ahci: sata@01c18000 {
+ ahci: sata@1c18000 {
compatible = "allwinner,sun4i-a10-ahci";
reg = <0x01c18000 0x1000>;
interrupts = <56>;
- clocks = <&pll6 0>, <&ahb_gates 25>;
+ clocks = <&ccu CLK_AHB_SATA>, <&ccu CLK_SATA>;
status = "disabled";
};
- ehci1: usb@01c1c000 {
+ ehci1: usb@1c1c000 {
compatible = "allwinner,sun4i-a10-ehci", "generic-ehci";
reg = <0x01c1c000 0x100>;
interrupts = <40>;
- clocks = <&ahb_gates 3>;
+ clocks = <&ccu CLK_AHB_EHCI1>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
};
- ohci1: usb@01c1c400 {
+ ohci1: usb@1c1c400 {
compatible = "allwinner,sun4i-a10-ohci", "generic-ohci";
reg = <0x01c1c400 0x100>;
interrupts = <65>;
- clocks = <&usb_clk 7>, <&ahb_gates 4>;
+ clocks = <&ccu CLK_USB_OHCI1>, <&ccu CLK_AHB_OHCI1>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
};
- spi3: spi@01c1f000 {
+ spi3: spi@1c1f000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c1f000 0x1000>;
interrupts = <50>;
- clocks = <&ahb_gates 23>, <&spi3_clk>;
+ clocks = <&ccu CLK_AHB_SPI3>, <&ccu CLK_SPI3>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 31>,
<&dma SUN4I_DMA_DEDICATED 30>;
#size-cells = <0>;
};
- intc: interrupt-controller@01c20400 {
+ ccu: clock@1c20000 {
+ compatible = "allwinner,sun4i-a10-ccu";
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ intc: interrupt-controller@1c20400 {
compatible = "allwinner,sun4i-a10-ic";
reg = <0x01c20400 0x400>;
interrupt-controller;
#interrupt-cells = <1>;
};
- pio: pinctrl@01c20800 {
+ pio: pinctrl@1c20800 {
compatible = "allwinner,sun4i-a10-pinctrl";
reg = <0x01c20800 0x400>;
interrupts = <28>;
- clocks = <&apb0_gates 5>;
+ clocks = <&ccu CLK_APB0_PIO>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
gpio-controller;
interrupt-controller;
#interrupt-cells = <3>;
#gpio-cells = <3>;
- emac_pins_a: emac0@0 {
- allwinner,pins = "PA0", "PA1", "PA2",
- "PA3", "PA4", "PA5", "PA6",
- "PA7", "PA8", "PA9", "PA10",
- "PA11", "PA12", "PA13", "PA14",
- "PA15", "PA16";
- allwinner,function = "emac";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ can0_ph_pins: can0-ph-pins {
+ pins = "PH20", "PH21";
+ function = "can";
};
- i2c0_pins_a: i2c0@0 {
- allwinner,pins = "PB0", "PB1";
- allwinner,function = "i2c0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ emac_pins: emac0-pins {
+ pins = "PA0", "PA1", "PA2",
+ "PA3", "PA4", "PA5", "PA6",
+ "PA7", "PA8", "PA9", "PA10",
+ "PA11", "PA12", "PA13", "PA14",
+ "PA15", "PA16";
+ function = "emac";
};
- i2c1_pins_a: i2c1@0 {
- allwinner,pins = "PB18", "PB19";
- allwinner,function = "i2c1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ i2c0_pins: i2c0-pins {
+ pins = "PB0", "PB1";
+ function = "i2c0";
};
- i2c2_pins_a: i2c2@0 {
- allwinner,pins = "PB20", "PB21";
- allwinner,function = "i2c2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ i2c1_pins: i2c1-pins {
+ pins = "PB18", "PB19";
+ function = "i2c1";
};
- ir0_rx_pins_a: ir0@0 {
- allwinner,pins = "PB4";
- allwinner,function = "ir0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ i2c2_pins: i2c2-pins {
+ pins = "PB20", "PB21";
+ function = "i2c2";
};
- ir0_tx_pins_a: ir0@1 {
- allwinner,pins = "PB3";
- allwinner,function = "ir0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ir0_rx_pins: ir0-rx-pin {
+ pins = "PB4";
+ function = "ir0";
};
- ir1_rx_pins_a: ir1@0 {
- allwinner,pins = "PB23";
- allwinner,function = "ir1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ir0_tx_pins: ir0-tx-pin {
+ pins = "PB3";
+ function = "ir0";
};
- ir1_tx_pins_a: ir1@1 {
- allwinner,pins = "PB22";
- allwinner,function = "ir1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ir1_rx_pins: ir1-rx-pin {
+ pins = "PB23";
+ function = "ir1";
};
- mmc0_pins_a: mmc0@0 {
- allwinner,pins = "PF0", "PF1", "PF2",
- "PF3", "PF4", "PF5";
- allwinner,function = "mmc0";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ir1_tx_pins: ir1-tx-pin {
+ pins = "PB22";
+ function = "ir1";
};
- mmc0_cd_pin_reference_design: mmc0_cd_pin@0 {
- allwinner,pins = "PH1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ mmc0_pins: mmc0-pins {
+ pins = "PF0", "PF1", "PF2",
+ "PF3", "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ bias-pull-up;
};
- ps20_pins_a: ps20@0 {
- allwinner,pins = "PI20", "PI21";
- allwinner,function = "ps2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ps2_ch0_pins: ps2-ch0-pins {
+ pins = "PI20", "PI21";
+ function = "ps2";
};
- ps21_pins_a: ps21@0 {
- allwinner,pins = "PH12", "PH13";
- allwinner,function = "ps2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ps2_ch1_ph_pins: ps2-ch1-ph-pins {
+ pins = "PH12", "PH13";
+ function = "ps2";
};
- pwm0_pins_a: pwm0@0 {
- allwinner,pins = "PB2";
- allwinner,function = "pwm";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pwm0_pin: pwm0-pin {
+ pins = "PB2";
+ function = "pwm";
};
- pwm1_pins_a: pwm1@0 {
- allwinner,pins = "PI3";
- allwinner,function = "pwm";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pwm1_pin: pwm1-pin {
+ pins = "PI3";
+ function = "pwm";
};
- spdif_tx_pins_a: spdif@0 {
- allwinner,pins = "PB13";
- allwinner,function = "spdif";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ spdif_tx_pin: spdif-tx-pin {
+ pins = "PB13";
+ function = "spdif";
+ bias-pull-up;
};
- spi0_pins_a: spi0@0 {
- allwinner,pins = "PI11", "PI12", "PI13";
- allwinner,function = "spi0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ spi0_pi_pins: spi0-pi-pins {
+ pins = "PI11", "PI12", "PI13";
+ function = "spi0";
};
- spi0_cs0_pins_a: spi0_cs0@0 {
- allwinner,pins = "PI10";
- allwinner,function = "spi0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ spi0_cs0_pi_pin: spi0-cs0-pi-pin {
+ pins = "PI10";
+ function = "spi0";
};
- spi1_pins_a: spi1@0 {
- allwinner,pins = "PI17", "PI18", "PI19";
- allwinner,function = "spi1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ spi1_pins: spi1-pins {
+ pins = "PI17", "PI18", "PI19";
+ function = "spi1";
};
- spi1_cs0_pins_a: spi1_cs0@0 {
- allwinner,pins = "PI16";
- allwinner,function = "spi1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ spi1_cs0_pin: spi1-cs0-pin {
+ pins = "PI16";
+ function = "spi1";
};
- spi2_pins_a: spi2@0 {
- allwinner,pins = "PC20", "PC21", "PC22";
- allwinner,function = "spi2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ spi2_pb_pins: spi2-pb-pins {
+ pins = "PB15", "PB16", "PB17";
+ function = "spi2";
};
- spi2_pins_b: spi2@1 {
- allwinner,pins = "PB15", "PB16", "PB17";
- allwinner,function = "spi2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ spi2_pc_pins: spi2-pc-pins {
+ pins = "PC20", "PC21", "PC22";
+ function = "spi2";
};
- spi2_cs0_pins_a: spi2_cs0@0 {
- allwinner,pins = "PC19";
- allwinner,function = "spi2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ spi2_cs0_pb_pin: spi2-cs0-pb-pin {
+ pins = "PB14";
+ function = "spi2";
};
- spi2_cs0_pins_b: spi2_cs0@1 {
- allwinner,pins = "PB14";
- allwinner,function = "spi2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ spi2_cs0_pc_pins: spi2-cs0-pc-pin {
+ pins = "PC19";
+ function = "spi2";
};
- uart0_pins_a: uart0@0 {
- allwinner,pins = "PB22", "PB23";
- allwinner,function = "uart0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart0_pb_pins: uart0-pb-pins {
+ pins = "PB22", "PB23";
+ function = "uart0";
};
- uart0_pins_b: uart0@1 {
- allwinner,pins = "PF2", "PF4";
- allwinner,function = "uart0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart0_pf_pins: uart0-pf-pins {
+ pins = "PF2", "PF4";
+ function = "uart0";
};
- uart1_pins_a: uart1@0 {
- allwinner,pins = "PA10", "PA11";
- allwinner,function = "uart1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart1_pins: uart1-pins {
+ pins = "PA10", "PA11";
+ function = "uart1";
};
};
- timer@01c20c00 {
+ timer@1c20c00 {
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0x90>;
interrupts = <22>;
clocks = <&osc24M>;
};
- wdt: watchdog@01c20c90 {
+ wdt: watchdog@1c20c90 {
compatible = "allwinner,sun4i-a10-wdt";
reg = <0x01c20c90 0x10>;
};
- rtc: rtc@01c20d00 {
+ rtc: rtc@1c20d00 {
compatible = "allwinner,sun4i-a10-rtc";
reg = <0x01c20d00 0x20>;
interrupts = <24>;
};
- pwm: pwm@01c20e00 {
+ pwm: pwm@1c20e00 {
compatible = "allwinner,sun4i-a10-pwm";
reg = <0x01c20e00 0xc>;
clocks = <&osc24M>;
status = "disabled";
};
- spdif: spdif@01c21000 {
+ spdif: spdif@1c21000 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun4i-a10-spdif";
reg = <0x01c21000 0x400>;
interrupts = <13>;
- clocks = <&apb0_gates 1>, <&spdif_clk>;
+ clocks = <&ccu CLK_APB0_SPDIF>, <&ccu CLK_SPDIF>;
clock-names = "apb", "spdif";
dmas = <&dma SUN4I_DMA_NORMAL 2>,
<&dma SUN4I_DMA_NORMAL 2>;
status = "disabled";
};
- ir0: ir@01c21800 {
+ ir0: ir@1c21800 {
compatible = "allwinner,sun4i-a10-ir";
- clocks = <&apb0_gates 6>, <&ir0_clk>;
+ clocks = <&ccu CLK_APB0_IR0>, <&ccu CLK_IR0>;
clock-names = "apb", "ir";
interrupts = <5>;
reg = <0x01c21800 0x40>;
status = "disabled";
};
- ir1: ir@01c21c00 {
+ ir1: ir@1c21c00 {
compatible = "allwinner,sun4i-a10-ir";
- clocks = <&apb0_gates 7>, <&ir1_clk>;
+ clocks = <&ccu CLK_APB0_IR1>, <&ccu CLK_IR1>;
clock-names = "apb", "ir";
interrupts = <6>;
reg = <0x01c21c00 0x40>;
status = "disabled";
};
- lradc: lradc@01c22800 {
+ i2s0: i2s@1c22400 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-i2s";
+ reg = <0x01c22400 0x400>;
+ interrupts = <16>;
+ clocks = <&ccu CLK_APB0_I2S0>, <&ccu CLK_I2S0>;
+ clock-names = "apb", "mod";
+ dmas = <&dma SUN4I_DMA_NORMAL 3>,
+ <&dma SUN4I_DMA_NORMAL 3>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ lradc: lradc@1c22800 {
compatible = "allwinner,sun4i-a10-lradc-keys";
reg = <0x01c22800 0x100>;
interrupts = <31>;
status = "disabled";
};
- codec: codec@01c22c00 {
+ codec: codec@1c22c00 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun4i-a10-codec";
reg = <0x01c22c00 0x40>;
interrupts = <30>;
- clocks = <&apb0_gates 0>, <&codec_clk>;
+ clocks = <&ccu CLK_APB0_CODEC>, <&ccu CLK_CODEC>;
clock-names = "apb", "codec";
dmas = <&dma SUN4I_DMA_NORMAL 19>,
<&dma SUN4I_DMA_NORMAL 19>;
status = "disabled";
};
- sid: eeprom@01c23800 {
+ sid: eeprom@1c23800 {
compatible = "allwinner,sun4i-a10-sid";
reg = <0x01c23800 0x10>;
};
- rtp: rtp@01c25000 {
+ rtp: rtp@1c25000 {
compatible = "allwinner,sun4i-a10-ts";
reg = <0x01c25000 0x100>;
interrupts = <29>;
#thermal-sensor-cells = <0>;
};
- uart0: serial@01c28000 {
+ uart0: serial@1c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
interrupts = <1>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 16>;
+ clocks = <&ccu CLK_APB1_UART0>;
status = "disabled";
};
- uart1: serial@01c28400 {
+ uart1: serial@1c28400 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28400 0x400>;
interrupts = <2>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 17>;
+ clocks = <&ccu CLK_APB1_UART1>;
status = "disabled";
};
- uart2: serial@01c28800 {
+ uart2: serial@1c28800 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28800 0x400>;
interrupts = <3>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 18>;
+ clocks = <&ccu CLK_APB1_UART2>;
status = "disabled";
};
- uart3: serial@01c28c00 {
+ uart3: serial@1c28c00 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28c00 0x400>;
interrupts = <4>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 19>;
+ clocks = <&ccu CLK_APB1_UART3>;
status = "disabled";
};
- uart4: serial@01c29000 {
+ uart4: serial@1c29000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c29000 0x400>;
interrupts = <17>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 20>;
+ clocks = <&ccu CLK_APB1_UART4>;
status = "disabled";
};
- uart5: serial@01c29400 {
+ uart5: serial@1c29400 {
compatible = "snps,dw-apb-uart";
reg = <0x01c29400 0x400>;
interrupts = <18>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 21>;
+ clocks = <&ccu CLK_APB1_UART5>;
status = "disabled";
};
- uart6: serial@01c29800 {
+ uart6: serial@1c29800 {
compatible = "snps,dw-apb-uart";
reg = <0x01c29800 0x400>;
interrupts = <19>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 22>;
+ clocks = <&ccu CLK_APB1_UART6>;
status = "disabled";
};
- uart7: serial@01c29c00 {
+ uart7: serial@1c29c00 {
compatible = "snps,dw-apb-uart";
reg = <0x01c29c00 0x400>;
interrupts = <20>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 23>;
+ clocks = <&ccu CLK_APB1_UART7>;
status = "disabled";
};
- i2c0: i2c@01c2ac00 {
+ ps20: ps2@1c2a000 {
+ compatible = "allwinner,sun4i-a10-ps2";
+ reg = <0x01c2a000 0x400>;
+ interrupts = <62>;
+ clocks = <&ccu CLK_APB1_PS20>;
+ status = "disabled";
+ };
+
+ ps21: ps2@1c2a400 {
+ compatible = "allwinner,sun4i-a10-ps2";
+ reg = <0x01c2a400 0x400>;
+ interrupts = <63>;
+ clocks = <&ccu CLK_APB1_PS21>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@1c2ac00 {
compatible = "allwinner,sun4i-a10-i2c";
reg = <0x01c2ac00 0x400>;
interrupts = <7>;
- clocks = <&apb1_gates 0>;
+ clocks = <&ccu CLK_APB1_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- i2c1: i2c@01c2b000 {
+ i2c1: i2c@1c2b000 {
compatible = "allwinner,sun4i-a10-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <8>;
- clocks = <&apb1_gates 1>;
+ clocks = <&ccu CLK_APB1_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- i2c2: i2c@01c2b400 {
+ i2c2: i2c@1c2b400 {
compatible = "allwinner,sun4i-a10-i2c";
reg = <0x01c2b400 0x400>;
interrupts = <9>;
- clocks = <&apb1_gates 2>;
+ clocks = <&ccu CLK_APB1_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- ps20: ps2@01c2a000 {
- compatible = "allwinner,sun4i-a10-ps2";
- reg = <0x01c2a000 0x400>;
- interrupts = <62>;
- clocks = <&apb1_gates 6>;
+ can0: can@1c2bc00 {
+ compatible = "allwinner,sun4i-a10-can";
+ reg = <0x01c2bc00 0x400>;
+ interrupts = <26>;
+ clocks = <&ccu CLK_APB1_CAN>;
status = "disabled";
};
- ps21: ps2@01c2a400 {
- compatible = "allwinner,sun4i-a10-ps2";
- reg = <0x01c2a400 0x400>;
- interrupts = <63>;
- clocks = <&apb1_gates 7>;
- status = "disabled";
+ fe0: display-frontend@1e00000 {
+ compatible = "allwinner,sun4i-a10-display-frontend";
+ reg = <0x01e00000 0x20000>;
+ interrupts = <47>;
+ clocks = <&ccu CLK_AHB_DE_FE0>, <&ccu CLK_DE_FE0>,
+ <&ccu CLK_DRAM_DE_FE0>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&ccu RST_DE_FE0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fe0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ fe0_out_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_in_fe0>;
+ };
+
+ fe0_out_be1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&be1_in_fe0>;
+ };
+ };
+ };
+ };
+
+ fe1: display-frontend@1e20000 {
+ compatible = "allwinner,sun4i-a10-display-frontend";
+ reg = <0x01e20000 0x20000>;
+ interrupts = <48>;
+ clocks = <&ccu CLK_AHB_DE_FE1>, <&ccu CLK_DE_FE1>,
+ <&ccu CLK_DRAM_DE_FE1>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&ccu RST_DE_FE1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fe1_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ fe1_out_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_in_fe1>;
+ };
+
+ fe1_out_be1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&be1_in_fe1>;
+ };
+ };
+ };
+ };
+
+ be1: display-backend@1e40000 {
+ compatible = "allwinner,sun4i-a10-display-backend";
+ reg = <0x01e40000 0x10000>;
+ interrupts = <48>;
+ clocks = <&ccu CLK_AHB_DE_BE1>, <&ccu CLK_DE_BE1>,
+ <&ccu CLK_DRAM_DE_BE1>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&ccu RST_DE_BE1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ be1_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ be1_in_fe0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&fe0_out_be1>;
+ };
+
+ be1_in_fe1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&fe1_out_be1>;
+ };
+ };
+
+ be1_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ be1_out_tcon0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_in_be1>;
+ };
+
+ be1_out_tcon1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&tcon1_in_be1>;
+ };
+ };
+ };
+ };
+
+ be0: display-backend@1e60000 {
+ compatible = "allwinner,sun4i-a10-display-backend";
+ reg = <0x01e60000 0x10000>;
+ interrupts = <47>;
+ clocks = <&ccu CLK_AHB_DE_BE0>, <&ccu CLK_DE_BE0>,
+ <&ccu CLK_DRAM_DE_BE0>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&ccu RST_DE_BE0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ be0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ be0_in_fe0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&fe0_out_be0>;
+ };
+
+ be0_in_fe1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&fe1_out_be0>;
+ };
+ };
+
+ be0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ be0_out_tcon0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_in_be0>;
+ };
+
+ be0_out_tcon1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&tcon1_in_be0>;
+ };
+ };
+ };
};
};
};
--- /dev/null
+/*
+ * Copyright (C) 2017 Priit Laes <plaes@plaes.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN4I_A10_H_
+#define _DT_BINDINGS_CLK_SUN4I_A10_H_
+
+#define CLK_HOSC 1
+#define CLK_PLL_VIDEO0_2X 9
+#define CLK_PLL_VIDEO1_2X 18
+#define CLK_CPU 20
+
+/* AHB Gates */
+#define CLK_AHB_OTG 26
+#define CLK_AHB_EHCI0 27
+#define CLK_AHB_OHCI0 28
+#define CLK_AHB_EHCI1 29
+#define CLK_AHB_OHCI1 30
+#define CLK_AHB_SS 31
+#define CLK_AHB_DMA 32
+#define CLK_AHB_BIST 33
+#define CLK_AHB_MMC0 34
+#define CLK_AHB_MMC1 35
+#define CLK_AHB_MMC2 36
+#define CLK_AHB_MMC3 37
+#define CLK_AHB_MS 38
+#define CLK_AHB_NAND 39
+#define CLK_AHB_SDRAM 40
+#define CLK_AHB_ACE 41
+#define CLK_AHB_EMAC 42
+#define CLK_AHB_TS 43
+#define CLK_AHB_SPI0 44
+#define CLK_AHB_SPI1 45
+#define CLK_AHB_SPI2 46
+#define CLK_AHB_SPI3 47
+#define CLK_AHB_PATA 48
+#define CLK_AHB_SATA 49
+#define CLK_AHB_GPS 50
+#define CLK_AHB_HSTIMER 51
+#define CLK_AHB_VE 52
+#define CLK_AHB_TVD 53
+#define CLK_AHB_TVE0 54
+#define CLK_AHB_TVE1 55
+#define CLK_AHB_LCD0 56
+#define CLK_AHB_LCD1 57
+#define CLK_AHB_CSI0 58
+#define CLK_AHB_CSI1 59
+#define CLK_AHB_HDMI0 60
+#define CLK_AHB_HDMI1 61
+#define CLK_AHB_DE_BE0 62
+#define CLK_AHB_DE_BE1 63
+#define CLK_AHB_DE_FE0 64
+#define CLK_AHB_DE_FE1 65
+#define CLK_AHB_GMAC 66
+#define CLK_AHB_MP 67
+#define CLK_AHB_GPU 68
+
+/* APB0 Gates */
+#define CLK_APB0_CODEC 69
+#define CLK_APB0_SPDIF 70
+#define CLK_APB0_I2S0 71
+#define CLK_APB0_AC97 72
+#define CLK_APB0_I2S1 73
+#define CLK_APB0_PIO 74
+#define CLK_APB0_IR0 75
+#define CLK_APB0_IR1 76
+#define CLK_APB0_I2S2 77
+#define CLK_APB0_KEYPAD 78
+
+/* APB1 Gates */
+#define CLK_APB1_I2C0 79
+#define CLK_APB1_I2C1 80
+#define CLK_APB1_I2C2 81
+#define CLK_APB1_I2C3 82
+#define CLK_APB1_CAN 83
+#define CLK_APB1_SCR 84
+#define CLK_APB1_PS20 85
+#define CLK_APB1_PS21 86
+#define CLK_APB1_I2C4 87
+#define CLK_APB1_UART0 88
+#define CLK_APB1_UART1 89
+#define CLK_APB1_UART2 90
+#define CLK_APB1_UART3 91
+#define CLK_APB1_UART4 92
+#define CLK_APB1_UART5 93
+#define CLK_APB1_UART6 94
+#define CLK_APB1_UART7 95
+
+/* IP clocks */
+#define CLK_NAND 96
+#define CLK_MS 97
+#define CLK_MMC0 98
+#define CLK_MMC0_OUTPUT 99
+#define CLK_MMC0_SAMPLE 100
+#define CLK_MMC1 101
+#define CLK_MMC1_OUTPUT 102
+#define CLK_MMC1_SAMPLE 103
+#define CLK_MMC2 104
+#define CLK_MMC2_OUTPUT 105
+#define CLK_MMC2_SAMPLE 106
+#define CLK_MMC3 107
+#define CLK_MMC3_OUTPUT 108
+#define CLK_MMC3_SAMPLE 109
+#define CLK_TS 110
+#define CLK_SS 111
+#define CLK_SPI0 112
+#define CLK_SPI1 113
+#define CLK_SPI2 114
+#define CLK_PATA 115
+#define CLK_IR0 116
+#define CLK_IR1 117
+#define CLK_I2S0 118
+#define CLK_AC97 119
+#define CLK_SPDIF 120
+#define CLK_KEYPAD 121
+#define CLK_SATA 122
+#define CLK_USB_OHCI0 123
+#define CLK_USB_OHCI1 124
+#define CLK_USB_PHY 125
+#define CLK_GPS 126
+#define CLK_SPI3 127
+#define CLK_I2S1 128
+#define CLK_I2S2 129
+
+/* DRAM Gates */
+#define CLK_DRAM_VE 130
+#define CLK_DRAM_CSI0 131
+#define CLK_DRAM_CSI1 132
+#define CLK_DRAM_TS 133
+#define CLK_DRAM_TVD 134
+#define CLK_DRAM_TVE0 135
+#define CLK_DRAM_TVE1 136
+#define CLK_DRAM_OUT 137
+#define CLK_DRAM_DE_FE1 138
+#define CLK_DRAM_DE_FE0 139
+#define CLK_DRAM_DE_BE0 140
+#define CLK_DRAM_DE_BE1 141
+#define CLK_DRAM_MP 142
+#define CLK_DRAM_ACE 143
+
+/* Display Engine Clocks */
+#define CLK_DE_BE0 144
+#define CLK_DE_BE1 145
+#define CLK_DE_FE0 146
+#define CLK_DE_FE1 147
+#define CLK_DE_MP 148
+#define CLK_TCON0_CH0 149
+#define CLK_TCON1_CH0 150
+#define CLK_CSI_SCLK 151
+#define CLK_TVD_SCLK2 152
+#define CLK_TVD 153
+#define CLK_TCON0_CH1_SCLK2 154
+#define CLK_TCON0_CH1 155
+#define CLK_TCON1_CH1_SCLK2 156
+#define CLK_TCON1_CH1 157
+#define CLK_CSI0 158
+#define CLK_CSI1 159
+#define CLK_CODEC 160
+#define CLK_VE 161
+#define CLK_AVS 162
+#define CLK_ACE 163
+#define CLK_HDMI 164
+#define CLK_GPU 165
+
+#endif /* _DT_BINDINGS_CLK_SUN4I_A10_H_ */
--- /dev/null
+/*
+ * Copyright (C) 2017 Priit Laes <plaes@plaes.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN4I_A10_H
+#define _DT_BINDINGS_RST_SUN4I_A10_H
+
+#define RST_USB_PHY0 1
+#define RST_USB_PHY1 2
+#define RST_USB_PHY2 3
+#define RST_GPS 4
+#define RST_DE_BE0 5
+#define RST_DE_BE1 6
+#define RST_DE_FE0 7
+#define RST_DE_FE1 8
+#define RST_DE_MP 9
+#define RST_TVE0 10
+#define RST_TCON0 11
+#define RST_TVE1 12
+#define RST_TCON1 13
+#define RST_CSI0 14
+#define RST_CSI1 15
+#define RST_VE 16
+#define RST_ACE 17
+#define RST_LVDS 18
+#define RST_GPU 19
+#define RST_HDMI_H 20
+#define RST_HDMI_SYS 21
+#define RST_HDMI_AUDIO_DMA 22
+
+#endif /* DT_BINDINGS_RST_SUN4I_A10_H */
projects / oweals / u-boot.git / commitdiff