/dts-v1/;
+#include <dt-bindings/usb/pd.h>
#include "imx8mm.dtsi"
/ {
gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
+
+ wm8524: audio-codec {
+ #sound-dai-cells = <0>;
+ compatible = "wlf,wm8524";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_wlf>;
+ wlf,mute-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>;
+ };
+
+ sound-wm8524 {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "wm8524-audio";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,frame-master = <&cpudai>;
+ simple-audio-card,bitclock-master = <&cpudai>;
+ simple-audio-card,widgets =
+ "Line", "Left Line Out Jack",
+ "Line", "Right Line Out Jack";
+ simple-audio-card,routing =
+ "Left Line Out Jack", "LINEVOUTL",
+ "Right Line Out Jack", "LINEVOUTR";
+
+ cpudai: simple-audio-card,cpu {
+ sound-dai = <&sai3>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&wm8524>;
+ clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
+ };
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
};
&fec1 {
ethphy0: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0>;
- at803x,led-act-blind-workaround;
- at803x,eee-okay;
- at803x,vddio-1p8v;
};
};
};
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic@4b {
+ compatible = "rohm,bd71847";
+ reg = <0x4b>;
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <3 GPIO_ACTIVE_LOW>;
+ rohm,reset-snvs-powered;
+
+ regulators {
+ buck1_reg: BUCK1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "BUCK2";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <1000000>;
+ rohm,dvs-idle-voltage = <900000>;
+ };
+
+ buck3_reg: BUCK3 {
+ // BUCK5 in datasheet
+ regulator-name = "BUCK3";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ // BUCK6 in datasheet
+ regulator-name = "BUCK4";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5_reg: BUCK5 {
+ // BUCK7 in datasheet
+ regulator-name = "BUCK5";
+ regulator-min-microvolt = <1605000>;
+ regulator-max-microvolt = <1995000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck6_reg: BUCK6 {
+ // BUCK8 in datasheet
+ regulator-name = "BUCK6";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "LDO3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "LDO4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "LDO6";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ ptn5110: tcpc@50 {
+ compatible = "nxp,ptn5110";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_typec1>;
+ reg = <0x50>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <11 8>;
+ status = "okay";
+
+ port {
+ typec1_dr_sw: endpoint {
+ remote-endpoint = <&usb1_drd_sw>;
+ };
+ };
+
+ typec1_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ data-role = "dual";
+ try-power-role = "sink";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(5000, 20000, 3000)>;
+ op-sink-microwatt = <15000000>;
+ self-powered;
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ pca6416: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&sai3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai3>;
+ assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+ assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+ assigned-clock-rates = <24576000>;
+ status = "okay";
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
&uart2 { /* console */
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "okay";
};
+&usbotg1 {
+ dr_mode = "otg";
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ usb1_drd_sw: endpoint {
+ remote-endpoint = <&typec1_dr_sw>;
+ };
+ };
+};
+
&usdhc2 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
>;
};
+ pinctrl_gpio_wlf: gpiowlfgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21 0xd6
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_pmic: pmicirq {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41
+ >;
+ };
+
pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
fsl,pins = <
MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41
>;
};
+ pinctrl_sai3: sai3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6
+ MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6
+ MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6
+ MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6
+ >;
+ };
+
+ pinctrl_typec1: typec1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_STROBE_GPIO2_IO11 0x159
+ >;
+ };
+
pinctrl_uart2: uart2grp {
fsl,pins = <
MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
#address-cells = <1>;
#size-cells = <0>;
+ idle-states {
+ entry-method = "psci";
+
+ cpu_pd_wait: cpu-pd-wait {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x0010033>;
+ local-timer-stop;
+ entry-latency-us = <1000>;
+ exit-latency-us = <700>;
+ min-residency-us = <2700>;
+ };
+ };
+
A53_0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a53";
enable-method = "psci";
next-level-cache = <&A53_L2>;
operating-points-v2 = <&a53_opp_table>;
+ nvmem-cells = <&cpu_speed_grade>;
+ nvmem-cell-names = "speed_grade";
+ cpu-idle-states = <&cpu_pd_wait>;
};
A53_1: cpu@1 {
enable-method = "psci";
next-level-cache = <&A53_L2>;
operating-points-v2 = <&a53_opp_table>;
+ cpu-idle-states = <&cpu_pd_wait>;
};
A53_2: cpu@2 {
enable-method = "psci";
next-level-cache = <&A53_L2>;
operating-points-v2 = <&a53_opp_table>;
+ cpu-idle-states = <&cpu_pd_wait>;
};
A53_3: cpu@3 {
enable-method = "psci";
next-level-cache = <&A53_L2>;
operating-points-v2 = <&a53_opp_table>;
+ cpu-idle-states = <&cpu_pd_wait>;
};
A53_L2: l2-cache0 {
opp-1200000000 {
opp-hz = /bits/ 64 <1200000000>;
opp-microvolt = <850000>;
+ opp-supported-hw = <0xe>, <0x7>;
clock-latency-ns = <150000>;
+ opp-suspend;
};
opp-1600000000 {
opp-hz = /bits/ 64 <1600000000>;
opp-microvolt = <900000>;
+ opp-supported-hw = <0xc>, <0x7>;
+ clock-latency-ns = <150000>;
+ opp-suspend;
+ };
+
+ opp-1800000000 {
+ opp-hz = /bits/ 64 <1800000000>;
+ opp-microvolt = <1000000>;
+ opp-supported-hw = <0x8>, <0x3>;
clock-latency-ns = <150000>;
opp-suspend;
};
clock-output-names = "clk_ext4";
};
- gic: interrupt-controller@38800000 {
- compatible = "arm,gic-v3";
- reg = <0x0 0x38800000 0 0x10000>, /* GIC Dist */
- <0x0 0x38880000 0 0xC0000>; /* GICR (RD_base + SGI_base) */
- #interrupt-cells = <3>;
- interrupt-controller;
- interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
- };
-
psci {
compatible = "arm,psci-1.0";
method = "smc";
arm,no-tick-in-suspend;
};
- soc {
+ usbphynop1: usbphynop1 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
+ assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
+ clock-names = "main_clk";
+ };
+
+ usbphynop2: usbphynop2 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
+ assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
+ clock-names = "main_clk";
+ };
+
+ soc@0 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,aips-bus", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
- ranges;
+ ranges = <0x30000000 0x30000000 0x400000>;
+
+ sai1: sai@30010000 {
+ compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+ reg = <0x30010000 0x10000>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_SAI1_IPG>,
+ <&clk IMX8MM_CLK_SAI1_ROOT>,
+ <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dmas = <&sdma2 0 2 0>, <&sdma2 1 2 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ sai2: sai@30020000 {
+ compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+ reg = <0x30020000 0x10000>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_SAI2_IPG>,
+ <&clk IMX8MM_CLK_SAI2_ROOT>,
+ <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dmas = <&sdma2 2 2 0>, <&sdma2 3 2 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ sai3: sai@30030000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+ reg = <0x30030000 0x10000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_SAI3_IPG>,
+ <&clk IMX8MM_CLK_SAI3_ROOT>,
+ <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dmas = <&sdma2 4 2 0>, <&sdma2 5 2 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ sai5: sai@30050000 {
+ compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+ reg = <0x30050000 0x10000>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_SAI5_IPG>,
+ <&clk IMX8MM_CLK_SAI5_ROOT>,
+ <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dmas = <&sdma2 8 2 0>, <&sdma2 9 2 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ sai6: sai@30060000 {
+ compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+ reg = <0x30060000 0x10000>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_SAI6_IPG>,
+ <&clk IMX8MM_CLK_SAI6_ROOT>,
+ <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dmas = <&sdma2 10 2 0>, <&sdma2 11 2 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
gpio1: gpio@30200000 {
compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
reg = <0x30200000 0x10000>;
interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_GPIO1_ROOT>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&iomuxc 0 10 30>;
};
gpio2: gpio@30210000 {
reg = <0x30210000 0x10000>;
interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_GPIO2_ROOT>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&iomuxc 0 40 21>;
};
gpio3: gpio@30220000 {
reg = <0x30220000 0x10000>;
interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_GPIO3_ROOT>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&iomuxc 0 61 26>;
};
gpio4: gpio@30230000 {
reg = <0x30230000 0x10000>;
interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_GPIO4_ROOT>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&iomuxc 0 87 32>;
};
gpio5: gpio@30240000 {
reg = <0x30240000 0x10000>;
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_GPIO5_ROOT>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&iomuxc 0 119 30>;
};
wdog1: watchdog@30280000 {
};
ocotp: ocotp-ctrl@30350000 {
- compatible = "fsl,imx8mm-ocotp", "fsl,imx7d-ocotp", "syscon";
+ compatible = "fsl,imx8mm-ocotp", "syscon";
reg = <0x30350000 0x10000>;
clocks = <&clk IMX8MM_CLK_OCOTP_ROOT>;
/* For nvmem subnodes */
#address-cells = <1>;
#size-cells = <1>;
+
+ cpu_speed_grade: speed-grade@10 {
+ reg = <0x10 4>;
+ };
};
anatop: anatop@30360000 {
offset = <0x34>;
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_SNVS_ROOT>;
+ clock-names = "snvs-rtc";
};
snvs_pwrkey: snvs-powerkey {
interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
linux,keycode = <KEY_POWER>;
wakeup-source;
+ status = "disabled";
};
};
<&clk_ext3>, <&clk_ext4>;
clock-names = "osc_32k", "osc_24m", "clk_ext1", "clk_ext2",
"clk_ext3", "clk_ext4";
+ assigned-clocks = <&clk IMX8MM_CLK_NOC>,
+ <&clk IMX8MM_CLK_AUDIO_AHB>,
+ <&clk IMX8MM_CLK_IPG_AUDIO_ROOT>,
+ <&clk IMX8MM_SYS_PLL3>,
+ <&clk IMX8MM_VIDEO_PLL1>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL3_OUT>,
+ <&clk IMX8MM_SYS_PLL1_800M>;
+ assigned-clock-rates = <0>,
+ <400000000>,
+ <400000000>,
+ <750000000>,
+ <594000000>;
};
src: reset-controller@30390000 {
- compatible = "fsl,imx8mm-src", "syscon";
+ compatible = "fsl,imx8mm-src", "fsl,imx8mq-src", "syscon";
reg = <0x30390000 0x10000>;
interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
#reset-cells = <1>;
compatible = "fsl,aips-bus", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
- ranges;
+ ranges = <0x30400000 0x30400000 0x400000>;
pwm1: pwm@30660000 {
compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm";
#pwm-cells = <2>;
status = "disabled";
};
+
+ system_counter: timer@306a0000 {
+ compatible = "nxp,sysctr-timer";
+ reg = <0x306a0000 0x20000>;
+ interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc_24m>;
+ clock-names = "per";
+ };
};
aips3: bus@30800000 {
compatible = "fsl,aips-bus", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
- ranges;
+ ranges = <0x30800000 0x30800000 0x400000>;
ecspi1: spi@30820000 {
compatible = "fsl,imx8mm-ecspi", "fsl,imx51-ecspi";
compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
reg = <0x30b40000 0x10000>;
interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk IMX8MM_CLK_DUMMY>,
+ clocks = <&clk IMX8MM_CLK_IPG_ROOT>,
<&clk IMX8MM_CLK_NAND_USDHC_BUS>,
<&clk IMX8MM_CLK_USDHC1_ROOT>;
clock-names = "ipg", "ahb", "per";
compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
reg = <0x30b50000 0x10000>;
interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk IMX8MM_CLK_DUMMY>,
+ clocks = <&clk IMX8MM_CLK_IPG_ROOT>,
<&clk IMX8MM_CLK_NAND_USDHC_BUS>,
<&clk IMX8MM_CLK_USDHC2_ROOT>;
clock-names = "ipg", "ahb", "per";
compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
reg = <0x30b60000 0x10000>;
interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk IMX8MM_CLK_DUMMY>,
+ clocks = <&clk IMX8MM_CLK_IPG_ROOT>,
<&clk IMX8MM_CLK_NAND_USDHC_BUS>,
<&clk IMX8MM_CLK_USDHC3_ROOT>;
clock-names = "ipg", "ahb", "per";
compatible = "fsl,aips-bus", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
- ranges;
+ ranges = <0x32c00000 0x32c00000 0x400000>;
usbotg1: usb@32e40000 {
compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb";
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk IMX8MM_CLK_USB1_CTRL_ROOT>;
clock-names = "usb1_ctrl_root_clk";
- assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>,
- <&clk IMX8MM_CLK_USB_CORE_REF>;
- assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>,
- <&clk IMX8MM_SYS_PLL1_100M>;
+ assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
fsl,usbphy = <&usbphynop1>;
fsl,usbmisc = <&usbmisc1 0>;
status = "disabled";
};
- usbphynop1: usbphynop1 {
- compatible = "usb-nop-xceiv";
- clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
- assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
- assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
- clock-names = "main_clk";
- };
-
usbmisc1: usbmisc@32e40200 {
compatible = "fsl,imx8mm-usbmisc", "fsl,imx7d-usbmisc";
#index-cells = <1>;
interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk IMX8MM_CLK_USB1_CTRL_ROOT>;
clock-names = "usb1_ctrl_root_clk";
- assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>,
- <&clk IMX8MM_CLK_USB_CORE_REF>;
- assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>,
- <&clk IMX8MM_SYS_PLL1_100M>;
+ assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
fsl,usbphy = <&usbphynop2>;
fsl,usbmisc = <&usbmisc2 0>;
status = "disabled";
};
- usbphynop2: usbphynop2 {
- compatible = "usb-nop-xceiv";
- clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
- assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
- assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
- clock-names = "main_clk";
- };
-
usbmisc2: usbmisc@32e50200 {
compatible = "fsl,imx8mm-usbmisc", "fsl,imx7d-usbmisc";
#index-cells = <1>;
dma-names = "rx-tx";
status = "disabled";
};
+
+ gic: interrupt-controller@38800000 {
+ compatible = "arm,gic-v3";
+ reg = <0x38800000 0x10000>, /* GIC Dist */
+ <0x38880000 0xc0000>; /* GICR (RD_base + SGI_base) */
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ ddr-pmu@3d800000 {
+ compatible = "fsl,imx8mm-ddr-pmu", "fsl,imx8m-ddr-pmu";
+ reg = <0x3d800000 0x400000>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ };
};
};
projects / oweals / u-boot.git / commitdiff