[PATCH] Update AMCC Yucca 440SPe eval board support

The AMCC Yucca now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.

Signed-off-by: Stefan Roese <sr@denx.de>

diff --git a/board/amcc/yucca/init.S b/board/amcc/yucca/init.S
index c9eca686b253300b87b9ef88d0244194ff41c738..c92dcf7a514a9a54a46537812390569a4393dfcf 100644 (file)
--- a/board/amcc/yucca/init.S
+++ b/board/amcc/yucca/init.S
@@ -1,4 +1,7 @@
 /*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
  *  Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
  *
  * See file CREDITS for list of people who contributed to this
@@ -19,56 +22,10 @@
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  */
-/* port to AMCC 440SPE evaluatioon board - SG April 12,2005  */
 
 #include <ppc_asm.tmpl>
 #include <config.h>
-
-/* General */
-#define TLB_VALID   0x00000200
-
-/* Supported page sizes */
-
-#define SZ_1K  0x00000000
-#define SZ_4K  0x00000010
-#define SZ_16K 0x00000020
-#define SZ_64K 0x00000030
-#define SZ_256K        0x00000040
-#define SZ_1M  0x00000050
-#define SZ_16M 0x00000070
-#define SZ_256M        0x00000090
-
-/* Storage attributes */
-#define SA_W   0x00000800      /* Write-through */
-#define SA_I   0x00000400      /* Caching inhibited */
-#define SA_M   0x00000200      /* Memory coherence */
-#define SA_G   0x00000100      /* Guarded */
-#define SA_E   0x00000080      /* Endian */
-
-/* Access control */
-#define AC_X   0x00000024      /* Execute */
-#define AC_W   0x00000012      /* Write */
-#define AC_R   0x00000009      /* Read */
-
-/* Some handy macros */
-
-#define EPN(e)         ((e) & 0xfffffc00)
-#define TLB0(epn,sz)   ((EPN((epn)) | (sz) | TLB_VALID ))
-#define TLB1(rpn,erpn) (((rpn) & 0xfffffc00) | (erpn))
-#define TLB2(a)                ((a) & 0x00000fbf)
-
-#define tlbtab_start\
-       mflr    r1      ;\
-       bl      0f      ;
-
-#define tlbtab_end\
-       .long 0, 0, 0   ;\
-0:     mflr    r0      ;\
-       mtlr    r1      ;\
-       blr             ;
-
-#define tlbentry(epn,sz,rpn,erpn,attr)\
-       .long TLB0(epn,sz),TLB1(rpn,erpn),TLB2(attr)
+#include <asm-ppc/mmu.h>
 
 /**************************************************************************
  * TLB TABLE
@@ -89,12 +46,18 @@
        .globl tlbtabA
 tlbtabA:
        tlbtab_start
-       tlbentry(0xfff00000, SZ_16M, 0xfff00000, 4, AC_R|AC_W|AC_X|SA_G)
 
-       tlbentry(CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
-       tlbentry(CFG_SDRAM_BASE + 0x10000000, SZ_256M, 0x10000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
-       tlbentry(CFG_SDRAM_BASE + 0x20000000, SZ_256M, 0x20000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
-       tlbentry(CFG_SDRAM_BASE + 0x30000000, SZ_256M, 0x30000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+       /*
+        * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
+        * speed up boot process. It is patched after relocation to enable SA_I
+        */
+       tlbentry(0xff000000, SZ_16M, 0xff000000, 4, AC_R|AC_W|AC_X|SA_G)
+
+       /*
+        * TLB entries for SDRAM are not needed on this platform.
+        * They are dynamically generated in the SPD DDR(2) detection
+        * routine.
+        */
 
        tlbentry(CFG_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_R|AC_W|AC_X|SA_I)
        tlbentry(CFG_FPGA_BASE, SZ_1K, 0xE2000000, 4,AC_R|AC_W|SA_I)
@@ -126,12 +89,18 @@ tlbtabA:
        .globl tlbtabB
 tlbtabB:
        tlbtab_start
-       tlbentry(0xfff00000, SZ_16M, 0xfff00000, 4, AC_R|AC_W|AC_X|SA_G)
 
-       tlbentry(CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
-       tlbentry(CFG_SDRAM_BASE + 0x10000000, SZ_256M, 0x10000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
-       tlbentry(CFG_SDRAM_BASE + 0x20000000, SZ_256M, 0x20000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
-       tlbentry(CFG_SDRAM_BASE + 0x30000000, SZ_256M, 0x30000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+       /*
+        * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
+        * speed up boot process. It is patched after relocation to enable SA_I
+        */
+       tlbentry(0xff000000, SZ_16M, 0xff000000, 4, AC_R|AC_W|AC_X|SA_G)
+
+       /*
+        * TLB entries for SDRAM are not needed on this platform.
+        * They are dynamically generated in the SPD DDR(2) detection
+        * routine.
+        */
 
        tlbentry(CFG_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_R|AC_W|AC_X|SA_I)
        tlbentry(CFG_FPGA_BASE, SZ_1K, 0xE2000000, 4,AC_R|AC_W|SA_I)

diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c
index e9b34dd249a9c9333c7cccf2138a978319fc0d81..90eaab1c80befc58c2ffa5ee782df9095a4640c4 100644 (file)
--- a/board/amcc/yucca/yucca.c
+++ b/board/amcc/yucca/yucca.c
@@ -44,8 +44,6 @@ int compare_to_true(char *str );
 char *remove_l_w_space(char *in_str );
 char *remove_t_w_space(char *in_str );
 int get_console_port(void);
-unsigned long ppcMfcpr(unsigned long cpr_reg);
-unsigned long ppcMfsdr(unsigned long sdr_reg);
 
 int ppc440spe_init_pcie_rootport(int port);
 void ppc440spe_setup_pcie(struct pci_controller *hose, int port);
@@ -221,7 +219,7 @@ int board_early_init_f (void)
         |
         +-------------------------------------------------------------------*/
        /* Read Pin Strap Register in PPC440SP */
-       sdr0_pinstp = ppcMfsdr(SDR0_PINSTP);
+       mfsdr(SDR0_PINSTP, sdr0_pinstp);
        bootstrap_settings = sdr0_pinstp & SDR0_PINSTP_BOOTSTRAP_MASK;
 
        switch (bootstrap_settings) {
@@ -246,7 +244,7 @@ int board_early_init_f (void)
                         * Boot Settings in IIC EEprom address 0x50 or 0x54
                         * Read Serial Device Strap Register1 in PPC440SPe
                         */
-                       sdr0_sdstp1 = ppcMfsdr(SDR0_SDSTP1);
+                       mfsdr(SDR0_SDSTP1, sdr0_sdstp1);
                        boot_selection = sdr0_sdstp1 & SDR0_SDSTP1_ERPN_MASK;
                        ebc_data_width = sdr0_sdstp1 & SDR0_SDSTP1_EBCW_MASK;
 
@@ -564,277 +562,6 @@ int checkboard (void)
        return 0;
 }
 
-static long int yucca_probe_for_dimms(void)
-{
-       int     dimm_installed[MAXDIMMS];
-       int     dimm_num, result;
-       int     dimms_found = 0;
-       uchar   dimm_addr = IIC0_DIMM0_ADDR;
-       uchar   dimm_spd_data[MAX_SPD_BYTES];
-
-       for (dimm_num = 0; dimm_num < MAXDIMMS; dimm_num++) {
-               /* check if there is a chip at the dimm address */
-               switch (dimm_num) {
-                       case 0:
-                               dimm_addr = IIC0_DIMM0_ADDR;
-                               break;
-                       case 1:
-                               dimm_addr = IIC0_DIMM1_ADDR;
-                               break;
-               }
-
-               result = i2c_probe(dimm_addr);
-
-               memset(dimm_spd_data, 0, MAX_SPD_BYTES * sizeof(char));
-               if (result == 0) {
-                       /* read first byte of SPD data, if there is any data */
-                       result = i2c_read(dimm_addr, 0, 1, dimm_spd_data, 1);
-
-                       if (result == 0) {
-                               result = dimm_spd_data[0];
-                               result = result > MAX_SPD_BYTES ?
-                                               MAX_SPD_BYTES : result;
-                               result = i2c_read(dimm_addr, 0, 1,
-                                                       dimm_spd_data, result);
-                       }
-               }
-
-               if ((result == 0) &&
-                   (dimm_spd_data[64] == MICRON_SPD_JEDEC_ID)) {
-                       dimm_installed[dimm_num] = TRUE;
-                       dimms_found++;
-                       debug("DIMM slot %d: DDR2 SDRAM detected\n", dimm_num);
-               } else {
-                       dimm_installed[dimm_num] = FALSE;
-                       debug("DIMM slot %d: Not populated or cannot sucessfully probe the DIMM\n", dimm_num);
-               }
-       }
-
-       if (dimms_found == 0) {
-               printf("ERROR - No memory installed.  Install a DDR-SDRAM DIMM.\n\n");
-               hang();
-       }
-
-       if (dimm_installed[0] != TRUE) {
-               printf("\nERROR - DIMM slot 0 must be populated before DIMM slot 1.\n");
-               printf("        Unsupported configuration. Move DIMM module from DIMM slot 1 to slot 0.\n\n");
-               hang();
-       }
-
-       return dimms_found;
-}
-
-/*************************************************************************
- * init SDRAM controller with fixed value
- * the initialization values are for 2x MICRON DDR2
- * PN: MT18HTF6472DY-53EB2
- * 512MB, DDR2, 533, CL4, ECC, REG
- ************************************************************************/
-static long int fixed_sdram(void)
-{
-       long int yucca_dimms = 0;
-
-       yucca_dimms = yucca_probe_for_dimms();
-
-       /* SDRAM0_MCOPT2 (0X21) Clear DCEN BIT  */
-       mtdcr( 0x10, 0x00000021 );
-       mtdcr( 0x11, 0x84000000 );
-
-       /* SDRAM0_MCOPT1 (0X20) ECC OFF / 64 bits / 4 banks / DDR2      */
-       mtdcr( 0x10, 0x00000020 );
-       mtdcr( 0x11, 0x2D122000 );
-
-       /* SET MCIF0_CODT   Die Termination On  */
-       mtdcr( 0x10, 0x00000026 );
-       if (yucca_dimms == 2)
-               mtdcr( 0x11, 0x2A800021 );
-       else if (yucca_dimms == 1)
-               mtdcr( 0x11, 0x02800021 );
-
-       /* On-Die Termination for Bank 0        */
-       mtdcr( 0x10, 0x00000022 );
-       if (yucca_dimms == 2)
-               mtdcr( 0x11, 0x18000000 );
-       else if (yucca_dimms == 1)
-               mtdcr( 0x11, 0x06000000 );
-
-       /*      On-Die Termination for Bank 1   */
-       mtdcr( 0x10, 0x00000023 );
-       if (yucca_dimms == 2)
-               mtdcr( 0x11, 0x18000000 );
-       else if (yucca_dimms == 1)
-               mtdcr( 0x11, 0x01800000 );
-
-       /*      On-Die Termination for Bank 2   */
-       mtdcr( 0x10, 0x00000024 );
-       if (yucca_dimms == 2)
-               mtdcr( 0x11, 0x01800000 );
-       else if (yucca_dimms == 1)
-               mtdcr( 0x11, 0x00000000 );
-
-       /*      On-Die Termination for Bank 3   */
-       mtdcr( 0x10, 0x00000025 );
-       if (yucca_dimms == 2)
-               mtdcr( 0x11, 0x01800000 );
-       else if (yucca_dimms == 1)
-               mtdcr( 0x11, 0x00000000 );
-
-       /* Refresh Time register (0x30) Refresh every 7.8125uS  */
-       mtdcr( 0x10, 0x00000030 );
-       mtdcr( 0x11, 0x08200000 );
-
-       /* SET MCIF0_MMODE       CL 4   */
-       mtdcr( 0x10, 0x00000088 );
-       mtdcr( 0x11, 0x00000642 );
-
-       /* MCIF0_MEMODE */
-       mtdcr( 0x10, 0x00000089 );
-       mtdcr( 0x11, 0x00000004 );
-
-       /*SET MCIF0_MB0CF       */
-       mtdcr( 0x10, 0x00000040 );
-       mtdcr( 0x11, 0x00000201 );
-
-       /* SET MCIF0_MB1CF      */
-       mtdcr( 0x10, 0x00000044 );
-       mtdcr( 0x11, 0x00000201 );
-
-       /* SET MCIF0_MB2CF      */
-       mtdcr( 0x10, 0x00000048 );
-       if (yucca_dimms == 2)
-               mtdcr( 0x11, 0x00000201 );
-       else if (yucca_dimms == 1)
-               mtdcr( 0x11, 0x00000000 );
-
-       /* SET MCIF0_MB3CF      */
-       mtdcr( 0x10, 0x0000004c );
-       if (yucca_dimms == 2)
-               mtdcr( 0x11, 0x00000201 );
-       else if (yucca_dimms == 1)
-               mtdcr( 0x11, 0x00000000 );
-
-       /* SET MCIF0_INITPLR0  # NOP            */
-       mtdcr( 0x10, 0x00000050 );
-       mtdcr( 0x11, 0xB5380000 );
-
-       /* SET MCIF0_INITPLR1  # PRE            */
-       mtdcr( 0x10, 0x00000051 );
-       mtdcr( 0x11, 0x82100400 );
-
-       /* SET MCIF0_INITPLR2  # EMR2           */
-       mtdcr( 0x10, 0x00000052 );
-       mtdcr( 0x11, 0x80820000 );
-
-       /* SET MCIF0_INITPLR3  # EMR3           */
-       mtdcr( 0x10, 0x00000053 );
-       mtdcr( 0x11, 0x80830000 );
-
-       /* SET MCIF0_INITPLR4  # EMR DLL ENABLE */
-       mtdcr( 0x10, 0x00000054 );
-       mtdcr( 0x11, 0x80810000 );
-
-       /* SET MCIF0_INITPLR5  # MR DLL RESET   */
-       mtdcr( 0x10, 0x00000055 );
-       mtdcr( 0x11, 0x80800542 );
-
-       /* SET MCIF0_INITPLR6  # PRE            */
-       mtdcr( 0x10, 0x00000056 );
-       mtdcr( 0x11, 0x82100400 );
-
-       /* SET MCIF0_INITPLR7  # Refresh        */
-       mtdcr( 0x10, 0x00000057 );
-       mtdcr( 0x11, 0x8A080000 );
-
-       /* SET MCIF0_INITPLR8  # Refresh        */
-       mtdcr( 0x10, 0x00000058 );
-       mtdcr( 0x11, 0x8A080000 );
-
-       /* SET MCIF0_INITPLR9  # Refresh        */
-       mtdcr( 0x10, 0x00000059 );
-       mtdcr( 0x11, 0x8A080000 );
-
-       /* SET MCIF0_INITPLR10 # Refresh        */
-       mtdcr( 0x10, 0x0000005A );
-       mtdcr( 0x11, 0x8A080000 );
-
-       /* SET MCIF0_INITPLR11 # MR             */
-       mtdcr( 0x10, 0x0000005B );
-       mtdcr( 0x11, 0x80800442 );
-
-       /* SET MCIF0_INITPLR12 # EMR OCD Default*/
-       mtdcr( 0x10, 0x0000005C );
-       mtdcr( 0x11, 0x80810380 );
-
-       /* SET MCIF0_INITPLR13 # EMR OCD Exit   */
-       mtdcr( 0x10, 0x0000005D );
-       mtdcr( 0x11, 0x80810000 );
-
-       /* 0x80: Adv Addr clock by 180 deg      */
-       mtdcr( 0x10, 0x00000080 );
-       mtdcr( 0x11, 0x80000000 );
-
-       /* 0x21: Exit self refresh, set DC_EN   */
-       mtdcr( 0x10, 0x00000021 );
-       mtdcr( 0x11, 0x28000000 );
-
-       /* 0x81: Write DQS Adv 90 + Fractional DQS Delay        */
-       mtdcr( 0x10, 0x00000081 );
-       mtdcr( 0x11, 0x80000800 );
-
-       /* MCIF0_SDTR1  */
-       mtdcr( 0x10, 0x00000085 );
-       mtdcr( 0x11, 0x80201000 );
-
-       /* MCIF0_SDTR2  */
-       mtdcr( 0x10, 0x00000086 );
-       mtdcr( 0x11, 0x42103242 );
-
-       /* MCIF0_SDTR3  */
-       mtdcr( 0x10, 0x00000087 );
-       mtdcr( 0x11, 0x0C100D14 );
-
-       /* SET MQ0_B0BAS  base addr 00000000 / 256MB    */
-       mtdcr( 0x40, 0x0000F800 );
-
-       /* SET MQ0_B1BAS  base addr 10000000 / 256MB    */
-       mtdcr( 0x41, 0x0400F800 );
-
-       /* SET MQ0_B2BAS  base addr 20000000 / 256MB    */
-       if (yucca_dimms == 2)
-               mtdcr( 0x42, 0x0800F800 );
-       else if (yucca_dimms == 1)
-               mtdcr( 0x42, 0x00000000 );
-
-       /* SET MQ0_B3BAS  base addr 30000000 / 256MB    */
-       if (yucca_dimms == 2)
-               mtdcr( 0x43, 0x0C00F800 );
-       else if (yucca_dimms == 1)
-               mtdcr( 0x43, 0x00000000 );
-
-       /* SDRAM_RQDC   */
-       mtdcr( 0x10, 0x00000070 );
-       mtdcr( 0x11, 0x8000003F );
-
-       /* SDRAM_RDCC   */
-       mtdcr( 0x10, 0x00000078 );
-       mtdcr( 0x11, 0x80000000 );
-
-       /* SDRAM_RFDC   */
-       mtdcr( 0x10, 0x00000074 );
-       mtdcr( 0x11, 0x00000220 );
-
-       return (yucca_dimms * 512) << 20;
-}
-
-long int initdram (int board_type)
-{
-       long dram_size = 0;
-
-       dram_size = fixed_sdram();
-
-       return dram_size;
-}
-
 #if defined(CFG_DRAM_TEST)
 int testdram (void)
 {
@@ -1267,42 +994,3 @@ int onboard_pci_arbiter_selected(int core_pci)
 #endif
        return (BOARD_OPTION_NOT_SELECTED);
 }
-
-/*---------------------------------------------------------------------------+
- | ppcMfcpr.
- +---------------------------------------------------------------------------*/
-unsigned long ppcMfcpr(unsigned long cpr_reg)
-{
-       unsigned long msr;
-       unsigned long cpr_cfgaddr_temp;
-       unsigned long cpr_value;
-
-       msr = (mfmsr () & ~(MSR_EE));
-       cpr_cfgaddr_temp =  mfdcr(CPR0_CFGADDR);
-       mtdcr(CPR0_CFGADDR, cpr_reg);
-       cpr_value =  mfdcr(CPR0_CFGDATA);
-       mtdcr(CPR0_CFGADDR, cpr_cfgaddr_temp);
-       mtmsr(msr);
-
-       return (cpr_value);
-}
-
-/*----------------------------------------------------------------------------+
-| Indirect Access of the System DCR's (SDR)
-| ppcMfsdr
-+----------------------------------------------------------------------------*/
-unsigned long ppcMfsdr(unsigned long sdr_reg)
-{
-       unsigned long msr;
-       unsigned long sdr_cfgaddr_temp;
-       unsigned long sdr_value;
-
-       msr = (mfmsr () & ~(MSR_EE));
-       sdr_cfgaddr_temp =  mfdcr(SDR0_CFGADDR);
-       mtdcr(SDR0_CFGADDR, sdr_reg);
-       sdr_value =  mfdcr(SDR0_CFGDATA);
-       mtdcr(SDR0_CFGADDR, sdr_cfgaddr_temp);
-       mtmsr(msr);
-
-       return (sdr_value);
-}

diff --git a/include/configs/yucca.h b/include/configs/yucca.h
index 6417ed891df4e9693a1fe89e648639ce98cd6c1d..eb4859c3e97162056e1656a2e474593f24be7caf 100644 (file)
--- a/include/configs/yucca.h
+++ b/include/configs/yucca.h
@@ -45,11 +45,11 @@
 #define EXTCLK_50              50000000
 #define EXTCLK_83              83333333
 
-#define        CONFIG_IBM_EMAC4_V4             1
-#define        CONFIG_MISC_INIT_F              1       /* Use misc_init_f()    */
+#define        CONFIG_MISC_INIT_F      1       /* Use misc_init_f()            */
+#define CONFIG_ADD_RAM_INFO    1       /* Print additional info        */
 #undef  CONFIG_SHOW_BOOT_PROGRESS
 #undef  CONFIG_STRESS
-#undef  ENABLE_ECC
+
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
@@ -118,10 +118,9 @@
 /*-----------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------*/
-#undef CONFIG_SPD_EEPROM               /* Use SPD EEPROM for setup     */
-#define SPD_EEPROM_ADDRESS {0x53, 0x52}        /* SPD i2c spd addresses        */
-#define IIC0_DIMM0_ADDR                0x53
-#define IIC0_DIMM1_ADDR                0x52
+#define CONFIG_SPD_EEPROM      1       /* Use SPD EEPROM for setup     */
+#define SPD_EEPROM_ADDRESS     {0x53, 0x52}    /* SPD i2c spd addresses*/
+#undef CONFIG_DDR_ECC                  /* no ECC support for now       */
 
 /*-----------------------------------------------------------------------
  * I2C
@@ -211,6 +210,7 @@
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
+#define        CONFIG_IBM_EMAC4_V4     1
 #define CONFIG_MII             1       /* MII PHY management           */
 #undef CONFIG_NET_MULTI
 #define CONFIG_PHY_ADDR                1       /* PHY address, See schematics  */