Add initial support for Freescale MX28EVK board.
Tested boot via SD card and by loading a kernel via TFTP through
the FEC interface.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Fabio Estevam <fabio.estevam@freescale.com>
mx25pdk i.MX25
+ mx28evk i.MX28
mx31pdk i.MX31
mx53ard i.MX53
mx53smd i.MX53
--- /dev/null
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+ifndef CONFIG_SPL_BUILD
+COBJS := mx28evk.o
+else
+COBJS := iomux.o
+endif
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+all: $(ALL)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+/*
+ * Freescale MX28EVK IOMUX setup
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+
+#define MUX_CONFIG_SSP0 (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define MUX_CONFIG_ENET (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define MUX_CONFIG_EMI (MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
+
+const iomux_cfg_t iomux_setup[] = {
+ /* DUART */
+ MX28_PAD_PWM0__DUART_RX,
+ MX28_PAD_PWM1__DUART_TX,
+
+ /* MMC0 */
+ MX28_PAD_SSP0_DATA0__SSP0_D0 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA1__SSP0_D1 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA2__SSP0_D2 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA3__SSP0_D3 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA4__SSP0_D4 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA5__SSP0_D5 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA6__SSP0_D6 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA7__SSP0_D7 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_CMD__SSP0_CMD | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+ MX28_PAD_SSP0_SCK__SSP0_SCK |
+ (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+ /* write protect */
+ MX28_PAD_SSP1_SCK__GPIO_2_12,
+ /* MMC0 slot power enable */
+ MX28_PAD_PWM3__GPIO_3_28 |
+ (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+ /* FEC0 */
+ MX28_PAD_ENET0_MDC__ENET0_MDC | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_MDIO__ENET0_MDIO | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET_CLK__CLKCTRL_ENET | MUX_CONFIG_ENET,
+ /* FEC0 Enable */
+ MX28_PAD_SSP1_DATA3__GPIO_2_15 |
+ (MXS_PAD_12MA | MXS_PAD_3V3),
+ /* FEC0 Reset */
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
+ (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+ /* FEC1 */
+ MX28_PAD_ENET0_COL__ENET1_TX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_CRS__ENET1_RX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RXD2__ENET1_RXD0 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RXD3__ENET1_RXD1 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TXD2__ENET1_TXD0 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TXD3__ENET1_TXD1 | MUX_CONFIG_ENET,
+
+ /* EMI */
+ MX28_PAD_EMI_D00__EMI_DATA0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D01__EMI_DATA1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D02__EMI_DATA2 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D03__EMI_DATA3 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D04__EMI_DATA4 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D05__EMI_DATA5 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D06__EMI_DATA6 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D07__EMI_DATA7 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D08__EMI_DATA8 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D09__EMI_DATA9 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D10__EMI_DATA10 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D11__EMI_DATA11 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D12__EMI_DATA12 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D13__EMI_DATA13 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D14__EMI_DATA14 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D15__EMI_DATA15 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_ODT0__EMI_ODT0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQM0__EMI_DQM0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_ODT1__EMI_ODT1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQM1__EMI_DQM1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CLK__EMI_CLK | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQS0__EMI_DQS0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQS1__EMI_DQS1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN | MUX_CONFIG_EMI,
+
+ MX28_PAD_EMI_A00__EMI_ADDR0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A01__EMI_ADDR1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A02__EMI_ADDR2 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A03__EMI_ADDR3 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A04__EMI_ADDR4 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A05__EMI_ADDR5 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A06__EMI_ADDR6 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A07__EMI_ADDR7 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A08__EMI_ADDR8 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A09__EMI_ADDR9 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A10__EMI_ADDR10 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A11__EMI_ADDR11 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A12__EMI_ADDR12 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A13__EMI_ADDR13 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A14__EMI_ADDR14 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_BA0__EMI_BA0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_BA1__EMI_BA1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_BA2__EMI_BA2 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CASN__EMI_CASN | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_RASN__EMI_RASN | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_WEN__EMI_WEN | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
+};
+
+void board_init_ll(void)
+{
+ mx28_common_spl_init(iomux_setup, ARRAY_SIZE(iomux_setup));
+}
--- /dev/null
+/*
+ * Freescale MX28EVK board
+ *
+ * (C) Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * Based on m28evk.c:
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <linux/mii.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <errno.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Functions
+ */
+int board_early_init_f(void)
+{
+ /* IO0 clock at 480MHz */
+ mx28_set_ioclk(MXC_IOCLK0, 480000);
+ /* IO1 clock at 480MHz */
+ mx28_set_ioclk(MXC_IOCLK1, 480000);
+
+ /* SSP0 clock at 96MHz */
+ mx28_set_sspclk(MXC_SSPCLK0, 96000, 0);
+ /* SSP2 clock at 96MHz */
+ mx28_set_sspclk(MXC_SSPCLK2, 96000, 0);
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ return mx28_dram_init();
+}
+
+int board_init(void)
+{
+ /* Adress of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+ return 0;
+}
+
+#ifdef CONFIG_CMD_MMC
+static int mx28evk_mmc_wp(int id)
+{
+ if (id != 0) {
+ printf("MXS MMC: Invalid card selected (card id = %d)\n", id);
+ return 1;
+ }
+
+ return gpio_get_value(MX28_PAD_SSP1_SCK__GPIO_2_12);
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ /* Configure WP as input */
+ gpio_direction_input(MX28_PAD_SSP1_SCK__GPIO_2_12);
+
+ /* Configure MMC0 Power Enable */
+ gpio_direction_output(MX28_PAD_PWM3__GPIO_3_28, 0);
+
+ return mxsmmc_initialize(bis, 0, mx28evk_mmc_wp);
+}
+#endif
+
+#ifdef CONFIG_CMD_NET
+
+#define MII_OPMODE_STRAP_OVERRIDE 0x16
+#define MII_PHY_CTRL1 0x1e
+#define MII_PHY_CTRL2 0x1f
+
+int fecmxc_mii_postcall(int phy)
+{
+ miiphy_write("FEC1", phy, MII_BMCR, 0x9000);
+ miiphy_write("FEC1", phy, MII_OPMODE_STRAP_OVERRIDE, 0x0202);
+ if (phy == 3)
+ miiphy_write("FEC1", 3, MII_PHY_CTRL2, 0x8180);
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ struct mx28_clkctrl_regs *clkctrl_regs =
+ (struct mx28_clkctrl_regs *)MXS_CLKCTRL_BASE;
+ struct eth_device *dev;
+ int ret;
+
+ ret = cpu_eth_init(bis);
+
+ /* MX28EVK uses ENET_CLK PAD to drive FEC clock */
+ writel(CLKCTRL_ENET_TIME_SEL_RMII_CLK | CLKCTRL_ENET_CLK_OUT_EN,
+ &clkctrl_regs->hw_clkctrl_enet);
+
+ /* Power-on FECs */
+ gpio_direction_output(MX28_PAD_SSP1_DATA3__GPIO_2_15, 0);
+
+ /* Reset FEC PHYs */
+ gpio_direction_output(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 0);
+ udelay(200);
+ gpio_set_value(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 1);
+
+ ret = fecmxc_initialize_multi(bis, 0, 0, MXS_ENET0_BASE);
+ if (ret) {
+ puts("FEC MXS: Unable to init FEC0\n");
+ return ret;
+ }
+
+ ret = fecmxc_initialize_multi(bis, 1, 3, MXS_ENET1_BASE);
+ if (ret) {
+ puts("FEC MXS: Unable to init FEC1\n");
+ return ret;
+ }
+
+ dev = eth_get_dev_by_name("FEC0");
+ if (!dev) {
+ puts("FEC MXS: Unable to get FEC0 device entry\n");
+ return -EINVAL;
+ }
+
+ ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+ if (ret) {
+ puts("FEC MXS: Unable to register FEC0 mii postcall\n");
+ return ret;
+ }
+
+ dev = eth_get_dev_by_name("FEC1");
+ if (!dev) {
+ puts("FEC MXS: Unable to get FEC1 device entry\n");
+ return -EINVAL;
+ }
+
+ ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+ if (ret) {
+ puts("FEC MXS: Unable to register FEC1 mii postcall\n");
+ return ret;
+ }
+
+ return ret;
+}
+
+#endif
--- /dev/null
+sources {
+ u_boot_spl="spl/u-boot-spl.bin";
+ u_boot="u-boot.bin";
+}
+
+section (0) {
+ load u_boot_spl > 0x0000;
+ load ivt (entry = 0x0014) > 0x8000;
+ hab call 0x8000;
+
+ load u_boot > 0x40000100;
+ load ivt (entry = 0x40000100) > 0x8000;
+ hab call 0x8000;
+}
imx27lite arm arm926ejs imx27lite logicpd mx27
magnesium arm arm926ejs imx27lite logicpd mx27
m28evk arm arm926ejs - denx mx28
+mx28evk arm arm926ejs - freescale mx28
nhk8815 arm arm926ejs nhk8815 st nomadik
nhk8815_onenand arm arm926ejs nhk8815 st nomadik nhk8815:BOOT_ONENAND
omap1610h2 arm arm926ejs omap1610inn ti omap omap1610inn:CS3_BOOT
--- /dev/null
+/*
+ * (C) Copyright 2011 Freescale Semiconductor, Inc.
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * Based on m28evk.h:
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/regs-base.h>
+
+/*
+ * SoC configurations
+ */
+#define CONFIG_MX28 /* i.MX28 SoC */
+#define CONFIG_MXS_GPIO /* GPIO control */
+#define CONFIG_SYS_HZ 1000 /* Ticks per second */
+
+#define CONFIG_MACH_TYPE MACH_TYPE_MX28EVK
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_ICACHE_OFF
+#define CONFIG_SYS_DCACHE_OFF
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_ARCH_MISC_INIT
+
+/*
+ * SPL
+ */
+#define CONFIG_SPL
+#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
+#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mx28"
+#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mx28/u-boot-spl.lds"
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+
+/*
+ * U-Boot Commands
+ */
+#include <config_cmd_default.h>
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_FAT
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_GPIO
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+
+/*
+ * Memory configurations
+ */
+#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
+#define PHYS_SDRAM_1 0x40000000 /* Base address */
+#define PHYS_SDRAM_1_SIZE 0x40000000 /* Max 1 GB RAM */
+#define CONFIG_STACKSIZE (128 * 1024) /* 128 KB stack */
+#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */
+#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */
+#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+/* Point initial SP in SRAM so SPL can use it too. */
+
+#define CONFIG_SYS_INIT_RAM_ADDR 0x00002000
+#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/*
+ * We need to sacrifice first 4 bytes of RAM here to avoid triggering some
+ * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot
+ * binary. In case there was more of this mess, 0x100 bytes are skipped.
+ */
+#define CONFIG_SYS_TEXT_BASE 0x40000100
+
+#define CONFIG_ENV_OVERWRITE
+/*
+ * U-Boot general configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT "MX28EVK U-Boot > "
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */
+#define CONFIG_SYS_PBSIZE \
+ (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+ /* Print buffer size */
+#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+ /* Boot argument buffer size */
+#define CONFIG_VERSION_VARIABLE /* U-BOOT version */
+#define CONFIG_AUTO_COMPLETE /* Command auto complete */
+#define CONFIG_CMDLINE_EDITING /* Command history etc */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/*
+ * Serial Driver
+ */
+#define CONFIG_PL011_SERIAL
+#define CONFIG_PL011_CLOCK 24000000
+#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE }
+#define CONFIG_CONS_INDEX 0
+#define CONFIG_BAUDRATE 115200 /* Default baud rate */
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * MMC Driver
+ */
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET (256 * 1024)
+#define CONFIG_ENV_SIZE (16 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_CMD_SAVEENV
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MXS_MMC
+#endif
+
+/*
+ * Ethernet on SOC (FEC)
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NET_MULTI
+#define CONFIG_ETHPRIME "FEC0"
+#define CONFIG_FEC_MXC
+#define CONFIG_FEC_MXC_MULTI
+#define CONFIG_MII
+#define CONFIG_DISCOVER_PHY
+#define CONFIG_FEC_XCV_TYPE RMII
+#define CONFIG_MX28_FEC_MAC_IN_OCOTP
+#endif
+
+/*
+ * Boot Linux
+ */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_BOOTCOMMAND "run bootcmd_net"
+#define CONFIG_LOADADDR 0x42000000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+/*
+ * Extra Environments
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "console_fsl=console=ttyAM0" \
+ "console_mainline=console=ttyAMA0" \
+ "netargs=setenv bootargs console=${console_mainline}" \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot}\0" \
+ "bootcmd_net=echo Booting from net ...; " \
+ "run netargs; " \
+ "dhcp ${uimage}; bootm\0" \
+
+#endif /* __CONFIG_H */
projects / oweals / u-boot.git / commitdiff