LIST_pxa=" \
cerf250 \
+ colibri_pxa270 \
cradle \
csb226 \
delta \
polaris \
pxa255_idp \
trizepsiv \
+ vpac270_nor \
+ vpac270_onenand \
wepep250 \
xaeniax \
xm250 \
xsengine \
+ zipitz2 \
zylonite \
"
fi;
@$(MKCONFIG) -n $@ -a trizepsiv arm pxa trizepsiv
+vpac270_nor_config \
+vpac270_onenand_config : unconfig
+ @mkdir -p $(obj)include
+ @if [ "$(findstring onenand,$@)" ] ; then \
+ echo "#define CONFIG_ONENAND_U_BOOT" \
+ >>$(obj)include/config.h ; \
+ fi;
+ @$(MKCONFIG) -n $@ -a vpac270 arm pxa vpac270
+
#########################################################################
## ARM1136 Systems
#########################################################################
vl_efw: 0,
};
#endif /* CONFIG_SHARP_LM8V31 */
+/*----------------------------------------------------------------------*/
+#ifdef CONFIG_VOIPAC_LCD
+
+# define LCD_BPP LCD_COLOR8
+# define LCD_INVERT_COLORS
+
+/* you have to set lccr0 and lccr3 (including pcd) */
+# define REG_LCCR0 0x043008f8
+# define REG_LCCR3 0x0340FF08
+
+vidinfo_t panel_info = {
+ vl_col: 640,
+ vl_row: 480,
+ vl_width: 157,
+ vl_height: 118,
+ vl_clkp: CONFIG_SYS_HIGH,
+ vl_oep: CONFIG_SYS_HIGH,
+ vl_hsp: CONFIG_SYS_HIGH,
+ vl_vsp: CONFIG_SYS_HIGH,
+ vl_dp: CONFIG_SYS_HIGH,
+ vl_bpix: LCD_BPP,
+ vl_lbw: 0,
+ vl_splt: 1,
+ vl_clor: 1,
+ vl_tft: 1,
+ vl_hpw: 32,
+ vl_blw: 144,
+ vl_elw: 32,
+ vl_vpw: 2,
+ vl_bfw: 13,
+ vl_efw: 30,
+};
+#endif /* CONFIG_VOIPAC_LCD */
/*----------------------------------------------------------------------*/
#ifdef CONFIG_HITACHI_SX14
};
#endif /* CONFIG_HITACHI_SX14 */
+/*----------------------------------------------------------------------*/
+#ifdef CONFIG_LMS283GF05
+
+# define LCD_BPP LCD_COLOR8
+//# define LCD_INVERT_COLORS
+
+/* you have to set lccr0 and lccr3 (including pcd) */
+# define REG_LCCR0 0x043008f8
+# define REG_LCCR3 0x03b00009
+
+vidinfo_t panel_info = {
+ vl_col: 240,
+ vl_row: 320,
+ vl_width: 240,
+ vl_height: 320,
+ vl_clkp: CONFIG_SYS_HIGH,
+ vl_oep: CONFIG_SYS_LOW,
+ vl_hsp: CONFIG_SYS_LOW,
+ vl_vsp: CONFIG_SYS_LOW,
+ vl_dp: CONFIG_SYS_HIGH,
+ vl_bpix: LCD_BPP,
+ vl_lbw: 0,
+ vl_splt: 1,
+ vl_clor: 1,
+ vl_tft: 1,
+ vl_hpw: 4,
+ vl_blw: 4,
+ vl_elw: 8,
+ vl_vpw: 4,
+ vl_bfw: 4,
+ vl_efw: 8,
+};
+#endif /* CONFIG_LMS283GF05 */
+
/*----------------------------------------------------------------------*/
#if LCD_BPP == LCD_COLOR8
return 0;
}
-
+#ifdef CONFIG_CPU_MONAHANS
+static inline void pxafb_setup_gpio (vidinfo_t *vid) {}
+#else
static void pxafb_setup_gpio (vidinfo_t *vid)
{
u_long lccr0;
printf("pxafb_setup_gpio: unable to determine bits per pixel\n");
}
}
+#endif
static void pxafb_enable_controller (vidinfo_t *vid)
{
FDADR1 = vid->pxa.fdadr1;
LCCR0 |= LCCR0_ENB;
+#ifdef CONFIG_CPU_MONAHANS
+ CKENA |= CKENA_1_LCD;
+#else
CKEN |= CKEN16_LCD;
+#endif
debug("FDADR0 = 0x%08x\n", (unsigned int)FDADR0);
debug("FDADR1 = 0x%08x\n", (unsigned int)FDADR1);
.globl _start
_start: b reset
+#ifdef CONFIG_PRELOADER
+ ldr pc, _hang
+ ldr pc, _hang
+ ldr pc, _hang
+ ldr pc, _hang
+ ldr pc, _hang
+ ldr pc, _hang
+ ldr pc, _hang
+
+_hang:
+ .word do_hang
+ .word 0x12345678
+ .word 0x12345678
+ .word 0x12345678
+ .word 0x12345678
+ .word 0x12345678
+ .word 0x12345678
+ .word 0x12345678 /* now 16*4=64 */
+#else
ldr pc, _undefined_instruction
ldr pc, _software_interrupt
ldr pc, _prefetch_abort
_not_used: .word not_used
_irq: .word irq
_fiq: .word fiq
+#endif /* CONFIG_PRELOADER */
.balignl 16,0xdeadbeef
relocate: /* relocate U-Boot to RAM */
adr r0, _start /* r0 <- current position of code */
ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
+#ifndef CONFIG_PRELOADER
cmp r0, r1 /* don't reloc during debug */
beq stack_setup
+#endif
ldr r2, _armboot_start
ldr r3, _bss_start
/* Set up the stack */
stack_setup:
ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #CONFIG_SYS_GBL_DATA_SIZE /* bdinfo */
+#ifdef CONFIG_PRELOADER
+ sub sp, r0, #128 /* leave 32 words for abort-stack */
+#else
+ sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
+ sub r0, r0, #CONFIG_SYS_GBL_DATA_SIZE /* bdinfo */
#ifdef CONFIG_USE_IRQ
sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
#endif /* CONFIG_USE_IRQ */
sub sp, r0, #12 /* leave 3 words for abort-stack */
bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
+#endif
clear_bss:
ldr r0, _bss_start /* find start of bss segment */
ldr r1, _bss_end /* stop here */
mov r2, #0x00000000 /* clear */
+#ifndef CONFIG_PRELOADER
clbss_l:str r2, [r0] /* clear loop... */
add r0, r0, #4
cmp r0, r1
ble clbss_l
+#endif
ldr pc, _start_armboot
+#ifdef CONFIG_ONENAND_IPL
+_start_armboot: .word start_oneboot
+#else
_start_armboot: .word start_armboot
-
+#endif
/****************************************************************************/
/* */
*/
mov pc, lr
-
+#ifndef CONFIG_PRELOADER
/****************************************************************************/
/* */
/* Interrupt handling */
.macro get_fiq_stack @ setup FIQ stack
ldr sp, FIQ_STACK_START
.endm
+#endif /* CONFIG_PRELOADER */
/****************************************************************************/
/* */
/****************************************************************************/
+#ifdef CONFIG_PRELOADER
+ .align 5
+do_hang:
+ ldr sp, _TEXT_BASE /* use 32 words abort stack */
+ bl hang /* hang and never return */
+#else /* !CONFIG_PRELOADER */
.align 5
undefined_instruction:
get_bad_stack
get_bad_stack
bad_save_user_regs
bl do_fiq
-
+#endif /* CONFIG_PRELOADER */
#endif /* CONFIG_USE_IRQ */
/****************************************************************************/
--- /dev/null
+/*
+ * arch/arm/include/asm/arch-pxa/macro.h
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __ASM_ARCH_PXA_MACRO_H__
+#define __ASM_ARCH_PXA_MACRO_H__
+#ifdef __ASSEMBLY__
+
+#include <asm/macro.h>
+#include <asm/arch/pxa-regs.h>
+
+/*
+ * This macro performs a 32bit write to a memory location and makes sure the
+ * write operation really happened by performing a read back.
+ *
+ * Clobbered regs: r4, r5
+ */
+.macro write32rb addr, data
+ ldr r4, =\addr
+ ldr r5, =\data
+ str r5, [r4]
+ ldr r5, [r4]
+.endm
+
+/*
+ * This macro waits according to OSCR incrementation
+ *
+ * Clobbered regs: r4, r5, r6
+ */
+.macro pxa_wait_ticks ticks
+ ldr r4, =OSCR
+ mov r5, #0
+ str r5, [r4]
+ ldr r5, =\ticks
+1:
+ ldr r6, [r4]
+ cmp r5, r6
+ bgt 1b
+.endm
+
+/*
+ * This macro sets up the GPIO pins of the PXA2xx/PXA3xx CPU
+ *
+ * Clobbered regs: r4, r5
+ */
+.macro pxa_gpio_setup
+ write32 GPSR0, CONFIG_SYS_GPSR0_VAL
+ write32 GPSR1, CONFIG_SYS_GPSR1_VAL
+ write32 GPSR2, CONFIG_SYS_GPSR2_VAL
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+ write32 GPSR3, CONFIG_SYS_GPSR3_VAL
+#endif
+
+ write32 GPCR0, CONFIG_SYS_GPCR0_VAL
+ write32 GPCR1, CONFIG_SYS_GPCR1_VAL
+ write32 GPCR2, CONFIG_SYS_GPCR2_VAL
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+ write32 GPCR3, CONFIG_SYS_GPCR3_VAL
+#endif
+
+ write32 GPDR0, CONFIG_SYS_GPDR0_VAL
+ write32 GPDR1, CONFIG_SYS_GPDR1_VAL
+ write32 GPDR2, CONFIG_SYS_GPDR2_VAL
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+ write32 GPDR3, CONFIG_SYS_GPDR3_VAL
+#endif
+
+ write32 GAFR0_L, CONFIG_SYS_GAFR0_L_VAL
+ write32 GAFR0_U, CONFIG_SYS_GAFR0_U_VAL
+ write32 GAFR1_L, CONFIG_SYS_GAFR1_L_VAL
+ write32 GAFR1_U, CONFIG_SYS_GAFR1_U_VAL
+ write32 GAFR2_L, CONFIG_SYS_GAFR2_L_VAL
+ write32 GAFR2_U, CONFIG_SYS_GAFR2_U_VAL
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+ write32 GAFR3_L, CONFIG_SYS_GAFR3_L_VAL
+ write32 GAFR3_U, CONFIG_SYS_GAFR3_U_VAL
+#endif
+
+ write32 PSSR, CONFIG_SYS_PSSR_VAL
+.endm
+
+/*
+ * This macro sets up the Memory controller of the PXA2xx CPU
+ *
+ * Clobbered regs: r3, r4, r5
+ */
+.macro pxa_mem_setup
+ /* This comes handy when setting MDREFR */
+ ldr r3, =MEMC_BASE
+
+ /*
+ * 1) Initialize Asynchronous static memory controller
+ */
+
+ /* MSC0: nCS(0,1) */
+ write32rb (MEMC_BASE + MSC0_OFFSET), CONFIG_SYS_MSC0_VAL
+ /* MSC1: nCS(2,3) */
+ write32rb (MEMC_BASE + MSC1_OFFSET), CONFIG_SYS_MSC1_VAL
+ /* MSC2: nCS(4,5) */
+ write32rb (MEMC_BASE + MSC2_OFFSET), CONFIG_SYS_MSC2_VAL
+
+ /*
+ * 2) Initialize Card Interface
+ */
+
+ /* MECR: Memory Expansion Card Register */
+ write32rb (MEMC_BASE + MECR_OFFSET), CONFIG_SYS_MECR_VAL
+ /* MCMEM0: Card Interface slot 0 timing */
+ write32rb (MEMC_BASE + MCMEM0_OFFSET), CONFIG_SYS_MCMEM0_VAL
+ /* MCMEM1: Card Interface slot 1 timing */
+ write32rb (MEMC_BASE + MCMEM1_OFFSET), CONFIG_SYS_MCMEM1_VAL
+ /* MCATT0: Card Interface Attribute Space Timing, slot 0 */
+ write32rb (MEMC_BASE + MCATT0_OFFSET), CONFIG_SYS_MCATT0_VAL
+ /* MCATT1: Card Interface Attribute Space Timing, slot 1 */
+ write32rb (MEMC_BASE + MCATT1_OFFSET), CONFIG_SYS_MCATT1_VAL
+ /* MCIO0: Card Interface I/O Space Timing, slot 0 */
+ write32rb (MEMC_BASE + MCIO0_OFFSET), CONFIG_SYS_MCIO0_VAL
+ /* MCIO1: Card Interface I/O Space Timing, slot 1 */
+ write32rb (MEMC_BASE + MCIO1_OFFSET), CONFIG_SYS_MCIO1_VAL
+
+ /*
+ * 3) Configure Fly-By DMA register
+ */
+
+ write32rb (MEMC_BASE + FLYCNFG_OFFSET), CONFIG_SYS_FLYCNFG_VAL
+
+ /*
+ * 4) Initialize Timing for Sync Memory (SDCLK0)
+ */
+
+ /*
+ * Before accessing MDREFR we need a valid DRI field, so we set
+ * this to power on defaults + DRI field.
+ */
+ ldr r5, [r3, #MDREFR_OFFSET]
+ bic r5, r5, #0x0ff
+ bic r5, r5, #0xf00 /* MDREFR user config with zeroed DRI */
+
+ ldr r4, =CONFIG_SYS_MDREFR_VAL
+ mov r6, r4
+ lsl r4, #20
+ lsr r4, #20 /* Get a valid DRI field */
+
+ orr r5, r5, r4 /* MDREFR user config with correct DRI */
+
+ orr r5, #MDREFR_K0RUN
+ orr r5, #MDREFR_SLFRSH
+ bic r5, #MDREFR_APD
+ bic r5, #MDREFR_E1PIN
+
+ str r5, [r3, #MDREFR_OFFSET]
+ ldr r4, [r3, #MDREFR_OFFSET]
+
+ /*
+ * 5) Initialize Synchronous Static Memory (Flash/Peripherals)
+ */
+
+ /* Initialize SXCNFG register. Assert the enable bits.
+ *
+ * Write SXMRS to cause an MRS command to all enabled banks of
+ * synchronous static memory. Note that SXLCR need not be written
+ * at this time.
+ */
+ write32rb (MEMC_BASE + SXCNFG_OFFSET), CONFIG_SYS_SXCNFG_VAL
+
+ /*
+ * 6) Initialize SDRAM
+ */
+
+ bic r6, #MDREFR_SLFRSH
+ str r6, [r3, #MDREFR_OFFSET]
+ ldr r4, [r3, #MDREFR_OFFSET]
+
+ orr r6, #MDREFR_E1PIN
+ str r6, [r3, #MDREFR_OFFSET]
+ ldr r4, [r3, #MDREFR_OFFSET]
+
+ /*
+ * 7) Write MDCNFG with MDCNFG:DEx deasserted (set to 0), to configure
+ * but not enable each SDRAM partition pair.
+ */
+
+ /* Fetch platform value of MDCNFG */
+ ldr r4, =CONFIG_SYS_MDCNFG_VAL
+ /* Disable all sdram banks */
+ bic r4, r4, #(MDCNFG_DE0|MDCNFG_DE1)
+ bic r4, r4, #(MDCNFG_DE2|MDCNFG_DE3)
+ /* Write initial value of MDCNFG, w/o enabling sdram banks */
+ str r4, [r3, #MDCNFG_OFFSET]
+ ldr r4, [r3, #MDCNFG_OFFSET]
+
+ /* Wait for the clock to the SDRAMs to stabilize, 100..200 usec. */
+ pxa_wait_ticks 0x300
+
+ /*
+ * 8) Trigger a number (usually 8) refresh cycles by attempting
+ * non-burst read or write accesses to disabled SDRAM, as commonly
+ * specified in the power up sequence documented in SDRAM data
+ * sheets. The address(es) used for this purpose must not be
+ * cacheable.
+ */
+
+ ldr r4, =CONFIG_SYS_DRAM_BASE
+.rept 9
+ str r5, [r4]
+.endr
+
+ /*
+ * 9) Write MDCNFG with enable bits asserted (MDCNFG:DEx set to 1).
+ */
+
+ ldr r5, =CONFIG_SYS_MDCNFG_VAL
+ ldr r4, =(MDCNFG_DE0 | MDCNFG_DE1 | MDCNFG_DE2 | MDCNFG_DE3)
+ and r5, r5, r4
+ ldr r4, [r3, #MDCNFG_OFFSET]
+ orr r4, r4, r5
+ str r4, [r3, #MDCNFG_OFFSET]
+ ldr r4, [r3, #MDCNFG_OFFSET]
+
+ /*
+ * 10) Write MDMRS.
+ */
+
+ ldr r4, =CONFIG_SYS_MDMRS_VAL
+ str r4, [r3, #MDMRS_OFFSET]
+ ldr r4, [r3, #MDMRS_OFFSET]
+
+ /*
+ * 11) Enable APD
+ */
+
+ ldr r4, [r3, #MDREFR_OFFSET]
+ and r6, r6, #MDREFR_APD
+ orr r4, r4, r6
+ str r4, [r3, #MDREFR_OFFSET]
+ ldr r4, [r3, #MDREFR_OFFSET]
+.endm
+
+/*
+ * This macro tests if the CPU woke up from sleep and eventually resumes
+ *
+ * Clobbered regs: r4, r5
+ */
+.macro pxa_wakeup
+ ldr r4, =RCSR
+ ldr r5, [r4]
+ and r5, r5, #(RCSR_GPR | RCSR_SMR | RCSR_WDR | RCSR_HWR)
+ str r5, [r4]
+ teq r5, #RCSR_SMR
+
+ bne pxa_wakeup_exit
+
+ ldr r4, =PSSR
+ mov r5, #PSSR_PH
+ str r5, [r4]
+
+ ldr r4, =PSPR
+ ldr pc, [r4]
+pxa_wakeup_exit:
+.endm
+
+/*
+ * This macro disables all interupts on PXA2xx/PXA3xx CPU
+ *
+ * Clobbered regs: r4, r5
+ */
+.macro pxa_intr_setup
+ write32 ICLR, 0
+ write32 ICMR, 0
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+ write32 ICLR2, 0
+ write32 ICMR2, 0
+#endif
+.endm
+
+/*
+ * This macro configures clock on PXA2xx/PXA3xx CPU
+ *
+ * Clobbered regs: r4, r5
+ */
+.macro pxa_clock_setup
+ /* Disable the peripheral clocks, and set the core clock frequency */
+
+ /* Turn Off ALL on-chip peripheral clocks for re-configuration */
+ write32 CKEN, CONFIG_SYS_CKEN
+
+ /* Write CCCR */
+ write32 CCCR, CONFIG_SYS_CCCR
+
+#ifdef CONFIG_RTC
+ /* enable the 32Khz oscillator for RTC and PowerManager */
+ write32 OSCC, #OSCC_OON
+ ldr r4, =OSCC
+
+ /* Spin here until OSCC.OOK get set, meaning the PLL has settled. */
+2:
+ ldr r5, [r4]
+ ands r5, r5, #1
+ beq 2b
+#endif
+.endm
+
+#endif /* __ASSEMBLY__ */
+#endif /* __ASM_ARCH_PXA_MACRO_H__ */
#define PWM_PWDUTY0 __REG(0x40B00004) /* PWM 0 Duty Cycle Register */
#define PWM_PERVAL0 __REG(0x40B00008) /* PWM 0 Period Control Register */
-#define PWM_CTRL1 __REG(0x40C00000) /* PWM 1Control Register */
+#define PWM_CTRL1 __REG(0x40C00000) /* PWM 1 Control Register */
#define PWM_PWDUTY1 __REG(0x40C00004) /* PWM 1 Duty Cycle Register */
#define PWM_PERVAL1 __REG(0x40C00008) /* PWM 1 Period Control Register */
+#define PWM_CTRL2 __REG(0x40B00010) /* PWM 2 Control Register */
+#define PWM_PWDUTY2 __REG(0x40B00014) /* PWM 2 Duty Cycle Register */
+#define PWM_PERVAL2 __REG(0x40B00018) /* PWM 2 Period Control Register */
+
+#define PWM_CTRL3 __REG(0x40C00010) /* PWM 3 Control Register */
+#define PWM_PWDUTY3 __REG(0x40C00014) /* PWM 3 Duty Cycle Register */
+#define PWM_PERVAL3 __REG(0x40C00018) /* PWM 3 Period Control Register */
+
/*
* Interrupt Controller
*/
--- /dev/null
+#
+# Toradex Colibri PXA270 Support
+#
+# Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = lib$(BOARD).a
+
+OBJS := colibri_pxa270.o
+SOBJS := lowlevel_init.o
+
+$(LIB): $(OBJS) $(SOBJS)
+ $(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+ $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
--- /dev/null
+/*
+ * Toradex Colibri PXA270 Support
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/hardware.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+extern struct serial_device serial_ffuart_device;
+extern struct serial_device serial_btuart_device;
+extern struct serial_device serial_stuart_device;
+
+struct serial_device *default_serial_console (void)
+{
+ return &serial_ffuart_device;
+}
+
+int board_init (void)
+{
+ /* memory and cpu-speed are setup before relocation */
+ /* so we do _nothing_ here */
+
+ /* arch number of vpac270 */
+ gd->bd->bi_arch_number = MACH_TYPE_COLIBRI;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = 0xa0000100;
+
+ return 0;
+}
+
+int dram_init (void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+ return 0;
+}
+
+#ifdef CONFIG_CMD_USB
+int usb_board_init(void)
+{
+ UHCHR = (UHCHR | UHCHR_PCPL | UHCHR_PSPL) &
+ ~(UHCHR_SSEP0 | UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSE);
+
+ UHCHR |= UHCHR_FSBIR;
+
+ while (UHCHR & UHCHR_FSBIR);
+
+ UHCHR &= ~UHCHR_SSE;
+ UHCHIE = (UHCHIE_UPRIE | UHCHIE_RWIE);
+
+ /* Clear any OTG Pin Hold */
+ if (PSSR & PSSR_OTGPH)
+ PSSR |= PSSR_OTGPH;
+
+ UHCRHDA &= ~(0x200);
+ UHCRHDA |= 0x100;
+
+ /* Set port power control mask bits, only 3 ports. */
+ UHCRHDB |= (0x7<<17);
+
+ /* enable port 2 */
+ UP2OCR |= UP2OCR_HXOE | UP2OCR_HXS | UP2OCR_DMPDE | UP2OCR_DPPDE;
+
+ return 0;
+}
+
+void usb_board_init_fail(void)
+{
+ return;
+}
+
+void usb_board_stop(void)
+{
+ UHCHR |= UHCHR_FHR;
+ udelay(11);
+ UHCHR &= ~UHCHR_FHR;
+
+ UHCCOMS |= 1;
+ udelay(10);
+
+ CKEN &= ~CKEN10_USBHOST;
+
+ return;
+}
+#endif
+
+#ifdef CONFIG_DRIVER_DM9000
+int board_eth_init(bd_t *bis)
+{
+ return dm9000_initialize(bis);
+}
+#endif
--- /dev/null
+TEXT_BASE = 0xa1000000
--- /dev/null
+/*
+ * Toradex Colibri PXA270 Lowlevel Hardware Initialization
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch/macro.h>
+
+.globl lowlevel_init
+lowlevel_init:
+ pxa_gpio_setup
+ pxa_wait_ticks 0x8000
+ pxa_mem_setup
+ pxa_wakeup
+ pxa_intr_setup
+ pxa_clock_setup
+
+ mov pc, lr
--- /dev/null
+
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = lib$(BOARD).a
+
+OBJS := vpac270.o
+SOBJS := lowlevel_init.o
+
+$(LIB): $(OBJS) $(SOBJS)
+ $(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+ $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
--- /dev/null
+TEXT_BASE = 0xa1000000
--- /dev/null
+/*
+ * Voipac PXA270 Lowlevel Hardware Initialization
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch/macro.h>
+
+.globl lowlevel_init
+lowlevel_init:
+ pxa_gpio_setup
+ pxa_wait_ticks 0x8000
+ pxa_mem_setup
+ pxa_wakeup
+ pxa_intr_setup
+ pxa_clock_setup
+
+ mov pc, lr
--- /dev/null
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ cpu/pxa/start.o (.text)
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(.rodata) }
+
+ . = ALIGN(4);
+ .data : { *(.data) }
+
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss : { *(.bss) }
+ _end = .;
+}
--- /dev/null
+/*
+ * (C) Copyright 2004
+ * Robert Whaley, Applied Data Systems, Inc. rwhaley@applieddata.net
+ *
+ * (C) Copyright 2002
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/hardware.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+extern struct serial_device serial_ffuart_device;
+extern struct serial_device serial_btuart_device;
+extern struct serial_device serial_stuart_device;
+
+struct serial_device *default_serial_console (void)
+{
+ return &serial_ffuart_device;
+}
+
+int board_init (void)
+{
+ /* memory and cpu-speed are setup before relocation */
+ /* so we do _nothing_ here */
+
+ /* arch number of vpac270 */
+ gd->bd->bi_arch_number = MACH_TYPE_VPAC270;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = 0xa0000100;
+
+ return 0;
+}
+
+int dram_init (void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+ gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+
+ return 0;
+}
+
+int usb_board_init(void)
+{
+ UHCHR = (UHCHR | UHCHR_PCPL | UHCHR_PSPL) &
+ ~(UHCHR_SSEP0 | UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSE);
+
+ UHCHR |= UHCHR_FSBIR;
+
+ while (UHCHR & UHCHR_FSBIR);
+
+ UHCHR &= ~UHCHR_SSE;
+ UHCHIE = (UHCHIE_UPRIE | UHCHIE_RWIE);
+
+ /* Clear any OTG Pin Hold */
+ if (PSSR & PSSR_OTGPH)
+ PSSR |= PSSR_OTGPH;
+
+ UHCRHDA &= ~(0x200);
+ UHCRHDA |= 0x100;
+
+ /* Set port power control mask bits, only 3 ports. */
+ UHCRHDB |= (0x7<<17);
+
+ /* enable port 2 */
+ UP2OCR |= UP2OCR_HXOE | UP2OCR_HXS | UP2OCR_DMPDE | UP2OCR_DPPDE;
+
+ return 0;
+}
+
+void usb_board_init_fail(void)
+{
+ return;
+}
+
+void usb_board_stop(void)
+{
+ UHCHR |= UHCHR_FHR;
+ udelay(11);
+ UHCHR &= ~UHCHR_FHR;
+
+ UHCCOMS |= 1;
+ udelay(10);
+
+ CKEN &= ~CKEN10_USBHOST;
+
+ return;
+}
+
+#ifdef CONFIG_DRIVER_DM9000
+int board_eth_init(bd_t *bis)
+{
+ return dm9000_initialize(bis);
+}
+#endif
--- /dev/null
+
+#
+# Copyright (C) 2009
+# Marek Vasut <marek.vasut@gmail.com>
+#
+# Heavily based on pxa255_idp platform
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := zipitz2.o
+SOBJS := lowlevel_init.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+TEXT_BASE = 0xa1000000
--- /dev/null
+/*
+ * Aeronix Zipit Z2 Lowlevel Hardware Initialization
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch/macro.h>
+
+.globl lowlevel_init
+lowlevel_init:
+ pxa_gpio_setup
+ pxa_wait_ticks 0x8000
+ pxa_mem_setup
+ pxa_wakeup
+ pxa_intr_setup
+ pxa_clock_setup
+
+ mov pc, lr
--- /dev/null
+/*
+ * (C) Copyright 2000-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ cpu/pxa/start.o (.text)
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+ . = ALIGN(4);
+ .data : { *(.data) }
+
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
+ _end = .;
+}
--- /dev/null
+/*
+ * Copyright (C) 2009
+ * Marek Vasut <marek.vasut@gmail.com>
+ *
+ * Heavily based on pxa255_idp platform
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <serial.h>
+#include <asm/arch/hardware.h>
+#include <spi.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_CMD_SPI
+void lcd_start(void);
+#else
+inline void lcd_start(void) {};
+#endif
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+ /* memory and cpu-speed are setup before relocation */
+ /* so we do _nothing_ here */
+
+ /* arch number of Lubbock-Board */
+ gd->bd->bi_arch_number = MACH_TYPE_ZIPIT2;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = 0xa0000100;
+
+ /* Enable LCD */
+ lcd_start();
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ setenv("stdout", "serial");
+ setenv("stderr", "serial");
+ return 0;
+}
+
+struct serial_device *default_serial_console (void)
+{
+ return &serial_stuart_device;
+}
+
+int dram_init (void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+ return 0;
+}
+
+#ifdef CONFIG_CMD_SPI
+
+struct {
+ unsigned char reg;
+ unsigned short data;
+ unsigned char mdelay;
+} lcd_data[] = {
+ { 0x07, 0x0000, 0 },
+ { 0x13, 0x0000, 10 },
+ { 0x11, 0x3004, 0 },
+ { 0x14, 0x200F, 0 },
+ { 0x10, 0x1a20, 0 },
+ { 0x13, 0x0040, 50 },
+ { 0x13, 0x0060, 0 },
+ { 0x13, 0x0070, 200 },
+ { 0x01, 0x0127, 0 },
+ { 0x02, 0x0700, 0 },
+ { 0x03, 0x1030, 0 },
+ { 0x08, 0x0208, 0 },
+ { 0x0B, 0x0620, 0 },
+ { 0x0C, 0x0110, 0 },
+ { 0x30, 0x0120, 0 },
+ { 0x31, 0x0127, 0 },
+ { 0x32, 0x0000, 0 },
+ { 0x33, 0x0503, 0 },
+ { 0x34, 0x0727, 0 },
+ { 0x35, 0x0124, 0 },
+ { 0x36, 0x0706, 0 },
+ { 0x37, 0x0701, 0 },
+ { 0x38, 0x0F00, 0 },
+ { 0x39, 0x0F00, 0 },
+ { 0x40, 0x0000, 0 },
+ { 0x41, 0x0000, 0 },
+ { 0x42, 0x013f, 0 },
+ { 0x43, 0x0000, 0 },
+ { 0x44, 0x013f, 0 },
+ { 0x45, 0x0000, 0 },
+ { 0x46, 0xef00, 0 },
+ { 0x47, 0x013f, 0 },
+ { 0x48, 0x0000, 0 },
+ { 0x07, 0x0015, 30 },
+ { 0x07, 0x0017, 0 },
+ { 0x20, 0x0000, 0 },
+ { 0x21, 0x0000, 0 },
+ { 0x22, 0x0000, 0 },
+};
+
+void zipitz2_spi_sda(int set)
+{
+ /* GPIO 13 */
+ if (set)
+ GPSR0 = (1 << 13);
+ else
+ GPCR0 = (1 << 13);
+}
+
+void zipitz2_spi_scl(int set)
+{
+ /* GPIO 22 */
+ if (set)
+ GPCR0 = (1 << 22);
+ else
+ GPSR0 = (1 << 22);
+}
+
+unsigned char zipitz2_spi_read(void)
+{
+ /* GPIO 40 */
+ return !!(GPLR1 & (1 << 8));
+}
+
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+ /* Always valid */
+ return 1;
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+ /* GPIO 88 low */
+ GPCR2 = (1 << 24);
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+ /* GPIO 88 high */
+ GPSR2 = (1 << 24);
+
+}
+
+void lcd_start(void)
+{
+ int i;
+ unsigned char reg[3] = { 0x74, 0x00, 0 };
+ unsigned char data[3] = { 0x76, 0, 0 };
+ unsigned char dummy[3] = { 0, 0, 0 };
+
+ /* PWM2 AF */
+ GAFR0_L |= 0x00800000;
+ /* Enable clock to all PWM */
+ CKEN |= 0x3;
+ /* Configure PWM2 */
+ PWM_CTRL2 = 0x4f;
+ PWM_PWDUTY2 = 0x2ff;
+ PWM_PERVAL2 = 792;
+
+ /* Toggle the reset pin to reset the LCD */
+ GPSR0 = (1 << 19);
+ udelay(100000);
+ GPCR0 = (1 << 19);
+ udelay(20000);
+ GPSR0 = (1 << 19);
+ udelay(20000);
+
+ /* Program the LCD init sequence */
+ for (i = 0; i < sizeof(lcd_data) / sizeof(lcd_data[0]); i++) {
+ reg[0] = 0x74;
+ reg[1] = 0x0;
+ reg[2] = lcd_data[i].reg;
+ spi_xfer(NULL, 24, reg, dummy, SPI_XFER_BEGIN | SPI_XFER_END);
+
+ data[0] = 0x76;
+ data[1] = lcd_data[i].data >> 8;
+ data[2] = lcd_data[i].data & 0xff;
+ spi_xfer(NULL, 24, data, dummy, SPI_XFER_BEGIN | SPI_XFER_END);
+
+ if (lcd_data[i].mdelay)
+ udelay(lcd_data[i].mdelay * 1000);
+ }
+
+ GPSR0 = (1 << 11);
+}
+#endif
actux4 arm ixp
ixdp425 arm ixp
cerf250 arm pxa
+colibri_pxa270 arm pxa
cradle arm pxa
csb226 arm pxa
delta arm pxa
pleb2 arm pxa
xaeniax arm pxa
xm250 arm pxa
+zipitz2 arm pxa
B2 arm s3c44b0 - dave
assabet arm sa1100
dnp1110 arm sa1100
#include <lcd.h>
#include <watchdog.h>
-#if defined(CONFIG_PXA250)
+#if defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS
#include <asm/byteorder.h>
#endif
uchar *bmap;
uchar *fb;
ushort *fb16;
-#if defined(CONFIG_PXA250)
+#if defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS
struct pxafb_info *fbi = &panel_info.pxa;
#elif defined(CONFIG_MPC823)
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
if (NBITS(panel_info.vl_bpix) < 12) {
/* Leave room for default color map */
-#if defined(CONFIG_PXA250)
+#if defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS
cmap = (ushort *)fbi->palette;
#elif defined(CONFIG_MPC823)
cmap = (ushort *)&(cp->lcd_cmap[BMP_LOGO_OFFSET*sizeof(ushort)]);
unsigned long pwidth = panel_info.vl_col;
unsigned colors, bpix, bmp_bpix;
unsigned long compression;
-#if defined(CONFIG_PXA250)
+#if defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS
struct pxafb_info *fbi = &panel_info.pxa;
#elif defined(CONFIG_MPC823)
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
#if !defined(CONFIG_MCC200)
/* MCC200 LCD doesn't need CMAP, supports 1bpp b&w only */
if (bmp_bpix == 8) {
-#if defined(CONFIG_PXA250)
+#if defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS
cmap = (ushort *)fbi->palette;
#elif defined(CONFIG_MPC823)
cmap = (ushort *)&(cp->lcd_cmap[255*sizeof(ushort)]);
WATCHDOG_RESET();
for (j = 0; j < width; j++) {
if (bpix != 16) {
-#if defined(CONFIG_PXA250) || defined(CONFIG_ATMEL_LCD)
+#if defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS || defined(CONFIG_ATMEL_LCD)
*(fb++) = *(bmap++);
#elif defined(CONFIG_MPC823) || defined(CONFIG_MCC200)
*(fb++) = 255 - *(bmap++);
--- /dev/null
+/*
+ * Toradex Colibri PXA270 configuration file
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Board Configuration Options
+ */
+#define CONFIG_PXA27X 1 /* Marvell PXA270 CPU */
+#define CONFIG_VPAC270 1 /* Toradex Colibri PXA270 board */
+
+#undef BOARD_LATE_INIT
+#undef CONFIG_SKIP_RELOCATE_UBOOT
+#undef CONFIG_USE_IRQ
+#undef CONFIG_SKIP_LOWLEVEL_INIT
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_SIZE 0x4000
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+#define CONFIG_ENV_OVERWRITE /* override default environment */
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmc init && fatload mmc 0 0xa0000000 uImage; then " \
+ "bootm 0xa0000000; " \
+ "fi; " \
+ "if usb reset && fatload usb 0 0xa0000000 uImage; then " \
+ "bootm 0xa0000000; " \
+ "fi; " \
+ "bootm 0x80000;"
+#define CONFIG_BOOTARGS "console=tty0 console=ttyS0,115200"
+#define CONFIG_TIMESTAMP
+#define CONFIG_BOOTDELAY 2 /* Autoboot delay */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+
+#define CONFIG_LZMA /* LZMA compression support */
+
+/*
+ * Serial Console Configuration
+ */
+#define CONFIG_PXA_SERIAL
+#define CONFIG_FFUART 1
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Bootloader Components Configuration
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_ENV
+#undef CONFIG_CMD_IMLS
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_FLASH
+
+/*
+ * Networking Configuration
+ * chip on the Voipac PXA270 board
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+
+#define CONFIG_NET_MULTI 1
+#define CONFIG_DRIVER_DM9000 1
+#define CONFIG_DM9000_BASE 0x08000000
+#define DM9000_IO (CONFIG_DM9000_BASE)
+#define DM9000_DATA (CONFIG_DM9000_BASE + 4)
+#define CONFIG_NET_RETRY_COUNT 10
+
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#endif
+
+/*
+ * MMC Card Configuration
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_PXA_MMC
+#define CONFIG_SYS_MMC_BASE 0xF0000000
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * KGDB
+ */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * HUSH Shell Configuration
+ */
+#define CONFIG_SYS_HUSH_PARSER 1
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "$ " /* Monitor Command Prompt */
+#else
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#endif
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_DEVICE_NULLDEV 1
+
+/*
+ * Clock Configuration
+ */
+#undef CONFIG_SYS_CLKS_IN_HZ
+#define CONFIG_SYS_HZ 3250000 /* Timer @ 3250000 Hz */
+#define CONFIG_SYS_CPUSPEED 0x290 /* 520 MHz */
+
+/*
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
+#endif
+
+/*
+ * DRAM Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1 /* We have 1 bank of DRAM */
+#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
+
+#define CONFIG_SYS_DRAM_BASE 0xa0000000 /* CS0 */
+#define CONFIG_SYS_DRAM_SIZE 0x04000000 /* 64 MB DRAM */
+
+#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR (0xa1000000)
+
+/*
+ * NOR FLASH
+ */
+#ifdef CONFIG_CMD_FLASH
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER 1
+
+#define CONFIG_SYS_MAX_FLASH_SECT (4 + 255)
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT (25*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (25*CONFIG_SYS_HZ)
+
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
+#define CONFIG_SYS_FLASH_PROTECTION 1
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+
+#else /* No flash */
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_ENV_IS_NOWHERE
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE 0x000000
+#define CONFIG_SYS_MONITOR_LEN 0x40000
+
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE 0x40000
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+
+/*
+ * GPIO settings
+ */
+#define CONFIG_SYS_GPSR0_VAL 0x00000000
+#define CONFIG_SYS_GPSR1_VAL 0x00020000
+#define CONFIG_SYS_GPSR2_VAL 0x0002C000
+#define CONFIG_SYS_GPSR3_VAL 0x00000000
+
+#define CONFIG_SYS_GPCR0_VAL 0x00000000
+#define CONFIG_SYS_GPCR1_VAL 0x00000000
+#define CONFIG_SYS_GPCR2_VAL 0x00000000
+#define CONFIG_SYS_GPCR3_VAL 0x00000000
+
+#define CONFIG_SYS_GPDR0_VAL 0x08000000
+#define CONFIG_SYS_GPDR1_VAL 0x0002A981
+#define CONFIG_SYS_GPDR2_VAL 0x0202FC00
+#define CONFIG_SYS_GPDR3_VAL 0x00000000
+
+#define CONFIG_SYS_GAFR0_L_VAL 0x00100000
+#define CONFIG_SYS_GAFR0_U_VAL 0x00C00010
+#define CONFIG_SYS_GAFR1_L_VAL 0x999A901A
+#define CONFIG_SYS_GAFR1_U_VAL 0xAAA00008
+#define CONFIG_SYS_GAFR2_L_VAL 0xAAAAAAAA
+#define CONFIG_SYS_GAFR2_U_VAL 0x0109A000
+#define CONFIG_SYS_GAFR3_L_VAL 0x54000300
+#define CONFIG_SYS_GAFR3_U_VAL 0x00024001
+
+#define CONFIG_SYS_PSSR_VAL 0x30
+
+/*
+ * Clock settings
+ */
+#define CONFIG_SYS_CKEN 0x00500240
+#define CONFIG_SYS_CCCR 0x02000290
+
+/*
+ * Memory settings
+ */
+#define CONFIG_SYS_MSC0_VAL 0x000095f2
+#define CONFIG_SYS_MSC1_VAL 0x00007ff4
+#define CONFIG_SYS_MSC2_VAL 0x00000000
+#define CONFIG_SYS_MDCNFG_VAL 0x08000ac9
+#define CONFIG_SYS_MDREFR_VAL 0x2013e01e
+#define CONFIG_SYS_MDMRS_VAL 0x00320032
+#define CONFIG_SYS_FLYCNFG_VAL 0x00000000
+#define CONFIG_SYS_SXCNFG_VAL 0x40044004
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+#define CONFIG_SYS_MECR_VAL 0x00000001
+#define CONFIG_SYS_MCMEM0_VAL 0x00014307
+#define CONFIG_SYS_MCMEM1_VAL 0x00014307
+#define CONFIG_SYS_MCATT0_VAL 0x0001c787
+#define CONFIG_SYS_MCATT1_VAL 0x0001c787
+#define CONFIG_SYS_MCIO0_VAL 0x0001430f
+#define CONFIG_SYS_MCIO1_VAL 0x0001430f
+
+/*
+ * USB
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
+#define CONFIG_SYS_USB_OHCI_BOARD_INIT
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
+#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x4C000000
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "tdex270"
+#define CONFIG_USB_STORAGE
+#endif
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * Voipac PXA270 configuration file
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Board Configuration Options
+ */
+#define CONFIG_PXA27X 1 /* Marvell PXA270 CPU */
+#define CONFIG_VPAC270 1 /* Voipac PXA270 board */
+
+#undef BOARD_LATE_INIT
+#undef CONFIG_SKIP_RELOCATE_UBOOT
+#undef CONFIG_USE_IRQ
+#undef CONFIG_SKIP_LOWLEVEL_INIT
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_SIZE 0x4000
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+#define CONFIG_ENV_OVERWRITE /* override default environment */
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmc init && fatload mmc 0 0xa4000000 uImage; then " \
+ "bootm 0xa4000000; " \
+ "fi; " \
+ "if usb reset && fatload usb 0 0xa4000000 uImage; then " \
+ "bootm 0xa4000000; " \
+ "fi; " \
+ "bootm 0x40000;"
+#define CONFIG_BOOTARGS "console=tty0 console=ttyS0,115200"
+#define CONFIG_TIMESTAMP
+#define CONFIG_BOOTDELAY 2 /* Autoboot delay */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+
+#define CONFIG_LZMA /* LZMA compression support */
+
+/*
+ * Serial Console Configuration
+ */
+#define CONFIG_PXA_SERIAL
+#define CONFIG_FFUART 1
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Bootloader Components Configuration
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_ENV
+#undef CONFIG_CMD_IMLS
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_USB
+#undef CONFIG_LCD
+#define CONFIG_CMD_IDE
+
+#ifdef CONFIG_ONENAND_U_BOOT
+#undef CONFIG_CMD_FLASH
+#define CONFIG_CMD_ONENAND
+#else
+#define CONFIG_CMD_FLASH
+#undef CONFIG_CMD_ONENAND
+#endif
+
+/*
+ * Networking Configuration
+ * chip on the Voipac PXA270 board
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+
+#define CONFIG_NET_MULTI 1
+#define CONFIG_DRIVER_DM9000 1
+#define CONFIG_DM9000_BASE 0x08000300 /* CS2 */
+#define DM9000_IO (CONFIG_DM9000_BASE)
+#define DM9000_DATA (CONFIG_DM9000_BASE + 4)
+#define CONFIG_NET_RETRY_COUNT 10
+
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#endif
+
+/*
+ * MMC Card Configuration
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_PXA_MMC
+#define CONFIG_SYS_MMC_BASE 0xF0000000
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * KGDB
+ */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * HUSH Shell Configuration
+ */
+#define CONFIG_SYS_HUSH_PARSER 1
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "$ " /* Monitor Command Prompt */
+#else
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#endif
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_DEVICE_NULLDEV 1
+
+/*
+ * Clock Configuration
+ */
+#undef CONFIG_SYS_CLKS_IN_HZ
+#define CONFIG_SYS_HZ 3250000 /* Timer @ 3250000 Hz */
+#define CONFIG_SYS_CPUSPEED 0x190 /* standard setting for 312MHz; L=16, N=1.5, A=0, SDCLK!=SystemBus */
+
+/*
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
+#endif
+
+/*
+ * DRAM Map
+ */
+#define CONFIG_NR_DRAM_BANKS 2 /* We have 2 banks of DRAM */
+#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */
+#define PHYS_SDRAM_2 0x80000000 /* SDRAM Bank #2 */
+#define PHYS_SDRAM_2_SIZE 0x08000000 /* 128 MB */
+
+#define CONFIG_SYS_DRAM_BASE 0xa0000000 /* CS0 */
+#define CONFIG_SYS_DRAM_SIZE 0x10000000 /* 256 MB DRAM */
+
+#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR (0x5c000000)
+
+/*
+ * NOR FLASH
+ */
+#if defined(CONFIG_CMD_FLASH) /* NOR */
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define PHYS_FLASH_2 0x02000000 /* Flash Bank #2 */
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER 1
+
+#define CONFIG_SYS_MAX_FLASH_SECT (4 + 255)
+#define CONFIG_SYS_MAX_FLASH_BANKS 2
+#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 }
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT (25*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (25*CONFIG_SYS_HZ)
+
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
+#define CONFIG_SYS_FLASH_PROTECTION 1
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+
+#elif defined(CONFIG_CMD_ONENAND) /* OneNAND */
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_ONENAND_BASE 0x00000000
+#define CONFIG_ENV_IS_IN_ONENAND 1
+
+#else /* No flash */
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_ENV_IS_NOWHERE
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE 0x000000
+#define CONFIG_SYS_MONITOR_LEN 0x40000
+
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE 0x40000
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+/*
+ * IDE
+ */
+#ifdef CONFIG_CMD_IDE
+#define CONFIG_LBA48
+#undef CONFIG_IDE_LED
+#undef CONFIG_IDE_RESET
+
+#define CONFIG_SYS_IDE_MAXBUS 1
+#define CONFIG_SYS_IDE_MAXDEVICE 1
+
+#define CONFIG_SYS_ATA_BASE_ADDR 0x0c000000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0
+
+#define CONFIG_SYS_ATA_DATA_OFFSET 0x120
+#define CONFIG_SYS_ATA_REG_OFFSET 0x120
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x120
+
+#define CONFIG_SYS_ATA_STRIDE 2
+#endif
+
+/*
+ * GPIO settings
+ */
+#define CONFIG_SYS_GPSR0_VAL 0x01308800
+#define CONFIG_SYS_GPSR1_VAL 0x00cf0000
+#define CONFIG_SYS_GPSR2_VAL 0x922ac000
+#define CONFIG_SYS_GPSR3_VAL 0x0161e800
+
+#define CONFIG_SYS_GPCR0_VAL 0x00010000
+#define CONFIG_SYS_GPCR1_VAL 0x0
+#define CONFIG_SYS_GPCR2_VAL 0x0
+#define CONFIG_SYS_GPCR3_VAL 0x0
+
+#define CONFIG_SYS_GPDR0_VAL 0xcbb18800
+#define CONFIG_SYS_GPDR1_VAL 0xfccfa981
+#define CONFIG_SYS_GPDR2_VAL 0x922affff
+#define CONFIG_SYS_GPDR3_VAL 0x0161e904
+
+#define CONFIG_SYS_GAFR0_L_VAL 0x00100000
+#define CONFIG_SYS_GAFR0_U_VAL 0xa5da8510
+#define CONFIG_SYS_GAFR1_L_VAL 0x6992901a
+#define CONFIG_SYS_GAFR1_U_VAL 0xaaa5a0aa
+#define CONFIG_SYS_GAFR2_L_VAL 0xaaaaaaaa
+#define CONFIG_SYS_GAFR2_U_VAL 0x4109a401
+#define CONFIG_SYS_GAFR3_L_VAL 0x54010310
+#define CONFIG_SYS_GAFR3_U_VAL 0x00025401
+
+#define CONFIG_SYS_PSSR_VAL 0x30
+
+/*
+ * Clock settings
+ */
+#define CONFIG_SYS_CKEN 0x00500240
+#define CONFIG_SYS_CCCR 0x02000290
+
+/*
+ * Memory settings
+ */
+#define CONFIG_SYS_MSC0_VAL 0x3ffc95fa
+#define CONFIG_SYS_MSC1_VAL 0x02ccf974
+#define CONFIG_SYS_MSC2_VAL 0x00000000
+#define CONFIG_SYS_MDCNFG_VAL 0x8ad30ad3
+#define CONFIG_SYS_MDREFR_VAL 0x201fe01e
+#define CONFIG_SYS_MDMRS_VAL 0x00000000
+#define CONFIG_SYS_FLYCNFG_VAL 0x00000000
+#define CONFIG_SYS_SXCNFG_VAL 0x40044004
+#define CONFIG_SYS_MEM_BUF_IMP 0x0f
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+#define CONFIG_SYS_MECR_VAL 0x00000001
+#define CONFIG_SYS_MCMEM0_VAL 0x00014307
+#define CONFIG_SYS_MCMEM1_VAL 0x00014307
+#define CONFIG_SYS_MCATT0_VAL 0x0001c787
+#define CONFIG_SYS_MCATT1_VAL 0x0001c787
+#define CONFIG_SYS_MCIO0_VAL 0x0001430f
+#define CONFIG_SYS_MCIO1_VAL 0x0001430f
+
+/*
+ * LCD
+ */
+#ifdef CONFIG_LCD
+#define CONFIG_VOIPAC_LCD
+#endif
+
+/*
+ * USB
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
+#define CONFIG_SYS_USB_OHCI_BOARD_INIT
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
+#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x4C000000
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "vpac270"
+#define CONFIG_USB_STORAGE
+#endif
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * Aeronix Zipit Z2 configuration file
+ *
+ * Copyright (C) 2009-2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Board Configuration Options
+ */
+#define CONFIG_PXA27X 1 /* Marvell PXA270 CPU */
+#define CONFIG_ZIPITZ2 1 /* Zipit Z2 board */
+
+#undef BOARD_LATE_INIT
+#undef CONFIG_SKIP_RELOCATE_UBOOT
+#undef CONFIG_USE_IRQ
+#undef CONFIG_SKIP_LOWLEVEL_INIT
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR 0x40000
+#define CONFIG_ENV_SIZE 0x20000
+
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + CONFIG_STACKSIZE)
+#define CONFIG_SYS_GBL_DATA_SIZE 512
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmc init && fatload mmc 0 0xa0000000 uboot.script ; then " \
+ "source 0xa0000000; " \
+ "else " \
+ "bootm 0x60000; " \
+ "fi; "
+#define CONFIG_BOOTARGS \
+ "console=tty0 console=ttyS2,115200 fbcon=rotate:3"
+#define CONFIG_TIMESTAMP
+#define CONFIG_BOOTDELAY 2 /* Autoboot delay */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+
+#define CONFIG_LZMA /* LZMA compression support */
+
+/*
+ * Serial Console Configuration
+ * STUART - the lower serial port on Colibri board
+ */
+#define CONFIG_PXA_SERIAL
+#define CONFIG_STUART 1
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Bootloader Components Configuration
+ */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_NET
+#define CONFIG_CMD_ENV
+#undef CONFIG_CMD_IMLS
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_SPI
+
+/*
+ * MMC Card Configuration
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_PXA_MMC
+#define CONFIG_SYS_MMC_BASE 0xF0000000
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * SPI and LCD
+ */
+#ifdef CONFIG_CMD_SPI
+#define CONFIG_SOFT_SPI
+#define CONFIG_LCD
+#define CONFIG_LMS283GF05
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_CMD_BMP
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_VIDEO_BMP_GZIP
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)
+#undef SPI_INIT
+
+#define SPI_DELAY udelay(10)
+#define SPI_SDA(val) zipitz2_spi_sda(val)
+#define SPI_SCL(val) zipitz2_spi_scl(val)
+#define SPI_READ zipitz2_spi_read()
+#ifndef __ASSEMBLY__
+void zipitz2_spi_sda(int);
+void zipitz2_spi_scl(int);
+unsigned char zipitz2_spi_read(void);
+#endif
+#endif
+
+/*
+ * KGDB
+ */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * HUSH Shell Configuration
+ */
+#define CONFIG_SYS_HUSH_PARSER 1
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "$ " /* Monitor Command Prompt */
+#else
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#endif
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_DEVICE_NULLDEV 1
+
+/*
+ * Clock Configuration
+ */
+#undef CONFIG_SYS_CLKS_IN_HZ
+#define CONFIG_SYS_HZ 3250000 /* Timer @ 3250000 Hz */
+#define CONFIG_SYS_CPUSPEED 0x190 /* standard setting for 312MHz; L=16, N=1.5, A=0, SDCLK!=SystemBus */
+
+/*
+ * Stack sizes
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
+#endif
+
+/*
+ * DRAM Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1 /* We have 1 bank of DRAM */
+#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */
+
+#define CONFIG_SYS_DRAM_BASE 0xa0000000 /* CS0 */
+#define CONFIG_SYS_DRAM_SIZE 0x02000000 /* 32 MB DRAM */
+
+#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_DRAM_BASE
+
+/*
+ * NOR FLASH
+ */
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define PHYS_FLASH_SIZE 0x00800000 /* 8 MB */
+#define PHYS_FLASH_SECT_SIZE 0x00010000 /* 64 KB sectors */
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER 1
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+
+#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1
+#define CONFIG_SYS_MONITOR_LEN PHYS_FLASH_SECT_SIZE
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 256
+
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_LOCK_TOUT (2*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_UNLOCK_TOUT (2*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_PROTECTION
+
+/*
+ * GPIO settings
+ */
+#define CONFIG_SYS_GAFR0_L_VAL 0x02000140
+#define CONFIG_SYS_GAFR0_U_VAL 0x59188000
+#define CONFIG_SYS_GAFR1_L_VAL 0x63900002
+#define CONFIG_SYS_GAFR1_U_VAL 0xaaa03950
+#define CONFIG_SYS_GAFR2_L_VAL 0x0aaaaaaa
+#define CONFIG_SYS_GAFR2_U_VAL 0x29000308
+#define CONFIG_SYS_GAFR3_L_VAL 0x54000000
+#define CONFIG_SYS_GAFR3_U_VAL 0x000000d5
+#define CONFIG_SYS_GPCR0_VAL 0x00000000
+#define CONFIG_SYS_GPCR1_VAL 0x00000020
+#define CONFIG_SYS_GPCR2_VAL 0x00000000
+#define CONFIG_SYS_GPCR3_VAL 0x00000000
+#define CONFIG_SYS_GPDR0_VAL 0xdafcee00
+#define CONFIG_SYS_GPDR1_VAL 0xffa3aaab
+#define CONFIG_SYS_GPDR2_VAL 0x8fe1ffff
+#define CONFIG_SYS_GPDR3_VAL 0x001b1f8a
+#define CONFIG_SYS_GPSR0_VAL 0x06080400
+#define CONFIG_SYS_GPSR1_VAL 0x007f0000
+#define CONFIG_SYS_GPSR2_VAL 0x032a0000
+#define CONFIG_SYS_GPSR3_VAL 0x00000180
+
+#define CONFIG_SYS_PSSR_VAL 0x30
+
+/*
+ * Clock settings
+ */
+#define CONFIG_SYS_CKEN 0x00511220
+#define CONFIG_SYS_CCCR 0x00000190
+
+/*
+ * Memory settings
+ */
+#define CONFIG_SYS_MSC0_VAL 0x2ffc38f8
+#define CONFIG_SYS_MSC1_VAL 0x0000ccd1
+#define CONFIG_SYS_MSC2_VAL 0x0000b884
+#define CONFIG_SYS_MDCNFG_VAL 0x08000ba9
+#define CONFIG_SYS_MDREFR_VAL 0x2011a01e
+#define CONFIG_SYS_MDMRS_VAL 0x00000000
+#define CONFIG_SYS_FLYCNFG_VAL 0x00010001
+#define CONFIG_SYS_SXCNFG_VAL 0x40044004
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+#define CONFIG_SYS_MECR_VAL 0x00000001
+#define CONFIG_SYS_MCMEM0_VAL 0x00014307
+#define CONFIG_SYS_MCMEM1_VAL 0x00014307
+#define CONFIG_SYS_MCATT0_VAL 0x0001c787
+#define CONFIG_SYS_MCATT1_VAL 0x0001c787
+#define CONFIG_SYS_MCIO0_VAL 0x0001430f
+#define CONFIG_SYS_MCIO1_VAL 0x0001430f
+
+#endif /* __CONFIG_H */
u_char vl_wbf; /* Wait between frames */
} vidinfo_t;
-#elif defined CONFIG_PXA250
+#elif defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS
/*
* PXA LCD DMA descriptor
*/
--- /dev/null
+IPL =onenand_ipl
+include $(TOPDIR)/config.mk
+
+LDSCRIPT= $(TOPDIR)/onenand_ipl/board/$(BOARDDIR)/u-boot.onenand.lds
+LDFLAGS = -Bstatic -T $(onenandobj)u-boot.lds -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS)
+AFLAGS += -DCONFIG_PRELOADER -DCONFIG_ONENAND_IPL
+CFLAGS += -DCONFIG_PRELOADER -DCONFIG_ONENAND_IPL
+OBJCFLAGS += --gap-fill=0x00
+
+SOBJS := lowlevel_init.o
+SOBJS += start.o
+COBJS := vpac270.o
+COBJS += onenand_read.o
+COBJS += onenand_boot.o
+
+SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS := $(SOBJS) $(COBJS)
+LNDIR := $(OBJTREE)/onenand_ipl/board/$(BOARDDIR)
+
+onenandobj := $(OBJTREE)/onenand_ipl/
+
+ALL = $(onenandobj)onenand-ipl $(onenandobj)onenand-ipl.bin $(onenandobj)onenand-ipl-2k.bin
+
+all: $(obj).depend $(ALL)
+
+$(onenandobj)onenand-ipl-2k.bin: $(onenandobj)onenand-ipl
+ $(OBJCOPY) ${OBJCFLAGS} --pad-to=0x5c040400 -O binary $< $@
+
+$(onenandobj)onenand-ipl.bin: $(onenandobj)onenand-ipl
+ $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(onenandobj)onenand-ipl: $(OBJS) $(onenandobj)u-boot.lds
+ cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \
+ -Map $@.map -o $@
+
+$(onenandobj)u-boot.lds: $(LDSCRIPT)
+ $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@
+
+# create symbolic links from common files
+
+# from cpu directory
+$(obj)start.S:
+ @rm -f $@
+ ln -s $(SRCTREE)/$(CPUDIR)/start.S $@
+
+# from onenand_ipl directory
+$(obj)onenand_ipl.h:
+ @rm -f $@
+ ln -s $(SRCTREE)/onenand_ipl/onenand_ipl.h $@
+
+$(obj)onenand_boot.c: $(obj)onenand_ipl.h
+ @rm -f $@
+ ln -s $(SRCTREE)/onenand_ipl/onenand_boot.c $@
+
+$(obj)onenand_read.c: $(obj)onenand_ipl.h
+ @rm -f $@
+ ln -s $(SRCTREE)/onenand_ipl/onenand_read.c $@
+
+ifneq ($(OBJTREE), $(SRCTREE))
+$(obj)vpac270.c:
+ @rm -f $@
+ ln -s $(SRCTREE)/onenand_ipl/board/$(BOARDDIR)/vpac270.c $@
+
+$(obj)lowlevel_init.S:
+ @rm -f $@
+ ln -s $(SRCTREE)/onenand_ipl/board/$(BOARDDIR)/lowlevel_init.S $@
+endif
+
+#########################################################################
+
+$(obj)%.o: $(obj)%.S
+ $(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o: $(obj)$.c
+ $(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+TEXT_BASE = 0x5c03fc00
--- /dev/null
+/*
+ * Voipac PXA270 Lowlevel Hardware Initialization
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch/macro.h>
+
+.globl lowlevel_init
+lowlevel_init:
+ pxa_clock_setup
+ mov pc, lr
--- /dev/null
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ start.o (.text)
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+ . = ALIGN(4);
+ .data : { *(.data) }
+
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss : { *(.bss) . = ALIGN(4); }
+ _end = .;
+}
--- /dev/null
+/*
+ * (C) Copyright 2004
+ * Robert Whaley, Applied Data Systems, Inc. rwhaley@applieddata.net
+ *
+ * (C) Copyright 2002
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/hardware.h>
+
+int board_init (void)
+{
+ return 0;
+}
+
+int s_init(int skip)
+{
+ return 0;
+}
projects / oweals / u-boot.git / commitdiff