#include <asm/global_data.h>
#include <asm/intel_regs.h>
#include <asm/mrccache.h>
+#include <asm/mrc_common.h>
#include <asm/mtrr.h>
#include <asm/pci.h>
#include <asm/report_platform.h>
#define CMOS_OFFSET_MRC_SEED_S3 156
#define CMOS_OFFSET_MRC_SEED_CHK 160
-/*
- * This function looks for the highest region of memory lower than 4GB which
- * has enough space for U-Boot where U-Boot is aligned on a page boundary.
- * It overrides the default implementation found elsewhere which simply
- * picks the end of ram, wherever that may be. The location of the stack,
- * the relocation address, and how far U-Boot is moved by relocation are
- * set in the global data structure.
- */
ulong board_get_usable_ram_top(ulong total_size)
{
- struct memory_info *info = &gd->arch.meminfo;
- uintptr_t dest_addr = 0;
- struct memory_area *largest = NULL;
- int i;
-
- /* Find largest area of memory below 4GB */
-
- for (i = 0; i < info->num_areas; i++) {
- struct memory_area *area = &info->area[i];
-
- if (area->start >= 1ULL << 32)
- continue;
- if (!largest || area->size > largest->size)
- largest = area;
- }
-
- /* If no suitable area was found, return an error. */
- assert(largest);
- if (!largest || largest->size < (2 << 20))
- panic("No available memory found for relocation");
-
- dest_addr = largest->start + largest->size;
-
- return (ulong)dest_addr;
+ return mrc_common_board_get_usable_ram_top(total_size);
}
void dram_init_banksize(void)
{
- struct memory_info *info = &gd->arch.meminfo;
- int num_banks;
- int i;
-
- for (i = 0, num_banks = 0; i < info->num_areas; i++) {
- struct memory_area *area = &info->area[i];
-
- if (area->start >= 1ULL << 32)
- continue;
- gd->bd->bi_dram[num_banks].start = area->start;
- gd->bd->bi_dram[num_banks].size = area->size;
- num_banks++;
- }
+ mrc_common_dram_init_banksize();
}
static int read_seed_from_cmos(struct pei_data *pei_data)
return 0;
}
-static const char *const ecc_decoder[] = {
- "inactive",
- "active on IO",
- "disabled on IO",
- "active"
-};
-
-/*
- * Dump in the log memory controller configuration as read from the memory
- * controller registers.
- */
-static void report_memory_config(void)
+static void post_system_agent_init(struct udevice *dev, struct udevice *me_dev,
+ struct pei_data *pei_data)
{
- u32 addr_decoder_common, addr_decode_ch[2];
- int i;
-
- addr_decoder_common = readl(MCHBAR_REG(0x5000));
- addr_decode_ch[0] = readl(MCHBAR_REG(0x5004));
- addr_decode_ch[1] = readl(MCHBAR_REG(0x5008));
-
- debug("memcfg DDR3 clock %d MHz\n",
- (readl(MCHBAR_REG(0x5e04)) * 13333 * 2 + 50) / 100);
- debug("memcfg channel assignment: A: %d, B % d, C % d\n",
- addr_decoder_common & 3,
- (addr_decoder_common >> 2) & 3,
- (addr_decoder_common >> 4) & 3);
-
- for (i = 0; i < ARRAY_SIZE(addr_decode_ch); i++) {
- u32 ch_conf = addr_decode_ch[i];
- debug("memcfg channel[%d] config (%8.8x):\n", i, ch_conf);
- debug(" ECC %s\n", ecc_decoder[(ch_conf >> 24) & 3]);
- debug(" enhanced interleave mode %s\n",
- ((ch_conf >> 22) & 1) ? "on" : "off");
- debug(" rank interleave %s\n",
- ((ch_conf >> 21) & 1) ? "on" : "off");
- debug(" DIMMA %d MB width x%d %s rank%s\n",
- ((ch_conf >> 0) & 0xff) * 256,
- ((ch_conf >> 19) & 1) ? 16 : 8,
- ((ch_conf >> 17) & 1) ? "dual" : "single",
- ((ch_conf >> 16) & 1) ? "" : ", selected");
- debug(" DIMMB %d MB width x%d %s rank%s\n",
- ((ch_conf >> 8) & 0xff) * 256,
- ((ch_conf >> 20) & 1) ? 16 : 8,
- ((ch_conf >> 18) & 1) ? "dual" : "single",
- ((ch_conf >> 16) & 1) ? ", selected" : "");
- }
-}
-
-static void post_system_agent_init(struct pei_data *pei_data)
-{
- /* If PCIe init is skipped, set the PEG clock gating */
- if (!pei_data->pcie_init)
- setbits_le32(MCHBAR_REG(0x7010), 1);
-}
-
-static asmlinkage void console_tx_byte(unsigned char byte)
-{
-#ifdef DEBUG
- putc(byte);
-#endif
-}
-
-static int recovery_mode_enabled(void)
-{
- return false;
-}
-
-/**
- * Find the PEI executable in the ROM and execute it.
- *
- * @dev: Northbridge device
- * @pei_data: configuration data for UEFI PEI reference code
- */
-int sdram_initialise(struct udevice *dev, struct udevice *me_dev,
- struct pei_data *pei_data)
-{
- unsigned version;
- const char *data;
uint16_t done;
- int ret;
-
- report_platform_info(dev);
-
- /* Wait for ME to be ready */
- ret = intel_early_me_init(me_dev);
- if (ret)
- return ret;
- ret = intel_early_me_uma_size(me_dev);
- if (ret < 0)
- return ret;
-
- debug("Starting UEFI PEI System Agent\n");
-
- /*
- * Do not pass MRC data in for recovery mode boot,
- * Always pass it in for S3 resume.
- */
- if (!recovery_mode_enabled() ||
- pei_data->boot_mode == PEI_BOOT_RESUME) {
- ret = prepare_mrc_cache(pei_data);
- if (ret)
- debug("prepare_mrc_cache failed: %d\n", ret);
- }
-
- /* If MRC data is not found we cannot continue S3 resume. */
- if (pei_data->boot_mode == PEI_BOOT_RESUME && !pei_data->mrc_input) {
- debug("Giving up in sdram_initialize: No MRC data\n");
- reset_cpu(0);
- }
-
- /* Pass console handler in pei_data */
- pei_data->tx_byte = console_tx_byte;
-
- debug("PEI data at %p, size %x:\n", pei_data, sizeof(*pei_data));
-
- data = (char *)CONFIG_X86_MRC_ADDR;
- if (data) {
- int rv;
- int (*func)(struct pei_data *);
- ulong start;
-
- debug("Calling MRC at %p\n", data);
- post_code(POST_PRE_MRC);
- start = get_timer(0);
- func = (int (*)(struct pei_data *))data;
- rv = func(pei_data);
- post_code(POST_MRC);
- if (rv) {
- switch (rv) {
- case -1:
- printf("PEI version mismatch.\n");
- break;
- case -2:
- printf("Invalid memory frequency.\n");
- break;
- default:
- printf("MRC returned %x.\n", rv);
- }
- printf("Nonzero MRC return value.\n");
- return -EFAULT;
- }
- debug("MRC execution time %lu ms\n", get_timer(start));
- } else {
- printf("UEFI PEI System Agent not found.\n");
- return -ENOSYS;
- }
-
-#if CONFIG_USBDEBUG
- /* mrc.bin reconfigures USB, so reinit it to have debug */
- early_usbdebug_init();
-#endif
-
- version = readl(MCHBAR_REG(0x5034));
- debug("System Agent Version %d.%d.%d Build %d\n",
- version >> 24 , (version >> 16) & 0xff,
- (version >> 8) & 0xff, version & 0xff);
- debug("MRC output data length %#x at %p\n", pei_data->mrc_output_len,
- pei_data->mrc_output);
/*
* Send ME init done for SandyBridge here. This is done inside the
else
intel_me_status(me_dev);
- post_system_agent_init(pei_data);
- report_memory_config();
-
- /* S3 resume: don't save scrambler seed or MRC data */
- if (pei_data->boot_mode != PEI_BOOT_RESUME) {
- /*
- * This will be copied to SDRAM in reserve_arch(), then written
- * to SPI flash in mrccache_save()
- */
- gd->arch.mrc_output = (char *)pei_data->mrc_output;
- gd->arch.mrc_output_len = pei_data->mrc_output_len;
- ret = write_seeds_to_cmos(pei_data);
- if (ret)
- debug("Failed to write seeds to CMOS: %d\n", ret);
- }
+ /* If PCIe init is skipped, set the PEG clock gating */
+ if (!pei_data->pcie_init)
+ setbits_le32(MCHBAR_REG(0x7010), 1);
+}
- return 0;
+static int recovery_mode_enabled(void)
+{
+ return false;
}
int reserve_arch(void)
return mrccache_reserve();
}
-static int copy_spd(struct pei_data *peid)
+static int copy_spd(struct udevice *dev, struct pei_data *peid)
{
- const int gpio_vector[] = {41, 42, 43, 10, -1};
- int spd_index;
- const void *blob = gd->fdt_blob;
- int node, spd_node;
- int ret, i;
-
- for (i = 0; ; i++) {
- if (gpio_vector[i] == -1)
- break;
- ret = gpio_requestf(gpio_vector[i], "spd_id%d", i);
- if (ret) {
- debug("%s: Could not request gpio %d\n", __func__,
- gpio_vector[i]);
- return ret;
- }
- }
- spd_index = gpio_get_values_as_int(gpio_vector);
- debug("spd index %d\n", spd_index);
- node = fdtdec_next_compatible(blob, 0, COMPAT_MEMORY_SPD);
- if (node < 0) {
- printf("SPD data not found.\n");
- return -ENOENT;
- }
-
- for (spd_node = fdt_first_subnode(blob, node);
- spd_node > 0;
- spd_node = fdt_next_subnode(blob, spd_node)) {
- const char *data;
- int len;
-
- if (fdtdec_get_int(blob, spd_node, "reg", -1) != spd_index)
- continue;
- data = fdt_getprop(blob, spd_node, "data", &len);
- if (len < sizeof(peid->spd_data[0])) {
- printf("Missing SPD data\n");
- return -EINVAL;
- }
-
- debug("Using SDRAM SPD data for '%s'\n",
- fdt_get_name(blob, spd_node, NULL));
- memcpy(peid->spd_data[0], data, sizeof(peid->spd_data[0]));
- break;
- }
-
- if (spd_node < 0) {
- printf("No SPD data found for index %d\n", spd_index);
- return -ENOENT;
- }
+ const void *data;
+ int ret;
- return 0;
-}
+ ret = mrc_locate_spd(dev, sizeof(peid->spd_data[0]), &data);
+ if (ret)
+ return ret;
-/**
- * add_memory_area() - Add a new usable memory area to our list
- *
- * Note: @start and @end must not span the first 4GB boundary
- *
- * @info: Place to store memory info
- * @start: Start of this memory area
- * @end: End of this memory area + 1
- */
-static int add_memory_area(struct memory_info *info,
- uint64_t start, uint64_t end)
-{
- struct memory_area *ptr;
-
- if (info->num_areas == CONFIG_NR_DRAM_BANKS)
- return -ENOSPC;
-
- ptr = &info->area[info->num_areas];
- ptr->start = start;
- ptr->size = end - start;
- info->total_memory += ptr->size;
- if (ptr->start < (1ULL << 32))
- info->total_32bit_memory += ptr->size;
- debug("%d: memory %llx size %llx, total now %llx / %llx\n",
- info->num_areas, ptr->start, ptr->size,
- info->total_32bit_memory, info->total_memory);
- info->num_areas++;
+ memcpy(peid->spd_data[0], data, sizeof(peid->spd_data[0]));
return 0;
}
debug("Available memory below 4GB: %lluM\n", tomk >> 10);
/* Report the memory regions */
- add_memory_area(info, 1 << 20, 2 << 28);
- add_memory_area(info, (2 << 28) + (2 << 20), 4 << 28);
- add_memory_area(info, (4 << 28) + (2 << 20), tseg_base);
- add_memory_area(info, 1ULL << 32, touud);
+ mrc_add_memory_area(info, 1 << 20, 2 << 28);
+ mrc_add_memory_area(info, (2 << 28) + (2 << 20), 4 << 28);
+ mrc_add_memory_area(info, (4 << 28) + (2 << 20), tseg_base);
+ mrc_add_memory_area(info, 1ULL << 32, touud);
/* Add MTRRs for memory */
mtrr_add_request(MTRR_TYPE_WRBACK, 0, 2ULL << 30);
int dram_init(void)
{
- struct pei_data pei_data __aligned(8) = {
+ struct pei_data _pei_data __aligned(8) = {
.pei_version = PEI_VERSION,
.mchbar = MCH_BASE_ADDRESS,
.dmibar = DEFAULT_DMIBAR,
{ 0, 4, 0x0000 }, /* P13= Empty */
},
};
+ struct pei_data *pei_data = &_pei_data;
struct udevice *dev, *me_dev;
int ret;
ret = syscon_get_by_driver_data(X86_SYSCON_ME, &me_dev);
if (ret)
return ret;
- debug("Boot mode %d\n", gd->arch.pei_boot_mode);
- debug("mrc_input %p\n", pei_data.mrc_input);
- pei_data.boot_mode = gd->arch.pei_boot_mode;
- ret = copy_spd(&pei_data);
- if (!ret)
- ret = sdram_initialise(dev, me_dev, &pei_data);
+ ret = copy_spd(dev, pei_data);
if (ret)
return ret;
+ pei_data->boot_mode = gd->arch.pei_boot_mode;
+ debug("Boot mode %d\n", gd->arch.pei_boot_mode);
+ debug("mrc_input %p\n", pei_data->mrc_input);
- rcba_config();
- quick_ram_check();
+ /*
+ * Do not pass MRC data in for recovery mode boot,
+ * Always pass it in for S3 resume.
+ */
+ if (!recovery_mode_enabled() ||
+ pei_data->boot_mode == PEI_BOOT_RESUME) {
+ ret = prepare_mrc_cache(pei_data);
+ if (ret)
+ debug("prepare_mrc_cache failed: %d\n", ret);
+ }
- writew(0xCAFE, MCHBAR_REG(SSKPD));
+ /* If MRC data is not found we cannot continue S3 resume. */
+ if (pei_data->boot_mode == PEI_BOOT_RESUME && !pei_data->mrc_input) {
+ debug("Giving up in sdram_initialize: No MRC data\n");
+ reset_cpu(0);
+ }
- post_code(POST_DRAM);
+ /* Pass console handler in pei_data */
+ pei_data->tx_byte = sdram_console_tx_byte;
- ret = sdram_find(dev);
+ /* Wait for ME to be ready */
+ ret = intel_early_me_init(me_dev);
if (ret)
return ret;
+ ret = intel_early_me_uma_size(me_dev);
+ if (ret < 0)
+ return ret;
+ ret = mrc_common_init(dev, pei_data, false);
+ if (ret)
+ return ret;
+
+ ret = sdram_find(dev);
+ if (ret)
+ return ret;
gd->ram_size = gd->arch.meminfo.total_32bit_memory;
+ debug("MRC output data length %#x at %p\n", pei_data->mrc_output_len,
+ pei_data->mrc_output);
+
+ post_system_agent_init(dev, me_dev, pei_data);
+ report_memory_config();
+
+ /* S3 resume: don't save scrambler seed or MRC data */
+ if (pei_data->boot_mode != PEI_BOOT_RESUME) {
+ /*
+ * This will be copied to SDRAM in reserve_arch(), then written
+ * to SPI flash in mrccache_save()
+ */
+ gd->arch.mrc_output = (char *)pei_data->mrc_output;
+ gd->arch.mrc_output_len = pei_data->mrc_output_len;
+ ret = write_seeds_to_cmos(pei_data);
+ if (ret)
+ debug("Failed to write seeds to CMOS: %d\n", ret);
+ }
+
+ writew(0xCAFE, MCHBAR_REG(SSKPD));
+ if (ret)
+ return ret;
+
+ rcba_config();
+
return 0;
}
projects / oweals / u-boot.git / commitdiff