#include "sun5i-a10s.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Auxtek t003 A10s hdmi tv-stick";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t003>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
- cd-inverted;
+ cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
status = "okay";
};
&pio {
mmc0_cd_pin_t003: mmc0_cd_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG1";
+ function = "gpio_in";
+ bias-pull-up;
};
led_pins_t003: led_pins@0 {
- allwinner,pins = "PB2";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_20_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB2";
+ function = "gpio_out";
+ drive-strength = <20>;
};
};
status = "okay";
};
-&usb0_vbus_pin_a {
- allwinner,pins = "PG13";
-};
-
-&usb1_vbus_pin_a {
- allwinner,pins = "PB10";
-};
-
&usb_otg {
dr_mode = "host";
status = "okay";
#include "sun5i-a10s.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Auxtek t004 A10s hdmi tv-stick";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t004>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
- cd-inverted;
+ cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
status = "okay";
};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ pins = "PG12";
+ function = "gpio_in";
+ bias-pull-up;
+ };
+
mmc0_cd_pin_t004: mmc0_cd_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG1";
+ function = "gpio_in";
+ bias-pull-up;
};
mmc1_vcc_en_pin_t004: mmc1_vcc_en_pin@0 {
- allwinner,pins = "PB18";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB18";
+ function = "gpio_out";
};
led_pins_t004: led_pins@0 {
- allwinner,pins = "PB2";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_20_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB2";
+ function = "gpio_out";
+ drive-strength = <20>;
};
};
status = "okay";
};
-&usb1_vbus_pin_a {
- allwinner,pins = "PG13";
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
};
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
};
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mk802>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
- cd-inverted;
+ cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
status = "okay";
};
&pio {
led_pins_mk802: led_pins@0 {
- allwinner,pins = "PB2";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB2";
+ function = "gpio_out";
};
mmc0_cd_pin_mk802: mmc0_cd_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG1";
+ function = "gpio_in";
+ bias-pull-up;
};
usb1_vbus_pin_mk802: usb1_vbus_pin@0 {
- allwinner,pins = "PB10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB10";
+ function = "gpio_out";
};
};
};
&usb_otg {
- dr_mode = "otg";
+ dr_mode = "peripheral";
status = "okay";
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Olimex A10s-Olinuxino Micro";
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
};
};
+&be0 {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
&emac {
pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_a>;
+ pinctrl-0 = <&emac_pins_b>;
phy = <&phy1>;
status = "okay";
};
status = "okay";
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino_micro>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
- cd-inverted;
+ cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
status = "okay";
};
pinctrl-0 = <&mmc1_pins_a>, <&mmc1_cd_pin_olinuxino_micro>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
- cd-inverted;
+ cd-gpios = <&pio 6 13 GPIO_ACTIVE_LOW>; /* PG13 */
status = "okay";
};
&pio {
mmc0_cd_pin_olinuxino_micro: mmc0_cd_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG1";
+ function = "gpio_in";
+ bias-pull-up;
};
mmc1_cd_pin_olinuxino_micro: mmc1_cd_pin@0 {
- allwinner,pins = "PG13";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG13";
+ function = "gpio_in";
+ bias-pull-up;
};
led_pins_olinuxino: led_pins@0 {
- allwinner,pins = "PE3";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_20_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PE3";
+ function = "gpio_out";
+ drive-strength = <20>;
};
usb1_vbus_pin_olinuxino_m: usb1_vbus_pin@0 {
- allwinner,pins = "PB10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB10";
+ function = "gpio_out";
};
usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PG12";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG12";
+ function = "gpio_in";
+ bias-pull-up;
};
};
&spi2 {
pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>,
- <&spi2_cs0_pins_a>;
+ pinctrl-0 = <&spi2_pins_b>,
+ <&spi2_cs0_pins_b>;
+ status = "okay";
+};
+
+&tcon0 {
status = "okay";
};
&uart2 {
pinctrl-names = "default";
- pinctrl-0 = <&uart2_pins_a>;
+ pinctrl-0 = <&uart2_pins_b>;
status = "okay";
};
status = "okay";
};
-&usb0_vbus_pin_a {
- allwinner,pins = "PG11";
-};
-
&usbphy {
pinctrl-names = "default";
pinctrl-0 = <&usb0_id_detect_pin>;
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "R7 A10s hdmi tv-stick";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_r7>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
- cd-inverted;
+ cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
status = "okay";
};
&pio {
mmc0_cd_pin_r7: mmc0_cd_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG1";
+ function = "gpio_in";
+ bias-pull-up;
};
led_pins_r7: led_pins@0 {
- allwinner,pins = "PB2";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_20_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB2";
+ function = "gpio_out";
+ drive-strength = <20>;
};
usb1_vbus_pin_r7: usb1_vbus_pin@0 {
- allwinner,pins = "PG13";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PG13";
+ function = "gpio_out";
};
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "A10s-Wobo i5";
&emac {
pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_b>;
+ pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_wobo_i5>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
- cd-inverted;
+ cd-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 */
status = "okay";
};
&pio {
led_pins_wobo_i5: led_pins@0 {
- allwinner,pins = "PB2";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB2";
+ function = "gpio_out";
};
mmc0_cd_pin_wobo_i5: mmc0_cd_pin@0 {
- allwinner,pins = "PB3";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PB3";
+ function = "gpio_in";
+ bias-pull-up;
};
emac_power_pin_wobo: emac_power_pin@0 {
- allwinner,pins = "PA02";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PA02";
+ function = "gpio_out";
};
};
status = "okay";
};
-&usb1_vbus_pin_a {
- allwinner,pins = "PG12";
-};
-
&usbphy {
usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
#include "sun5i.dtsi"
#include <dt-bindings/dma/sun4i-a10.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
interrupt-parent = <&intc>;
#size-cells = <1>;
ranges;
- framebuffer@0 {
+ framebuffer@2 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
- clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
- <&ahb_gates 43>, <&ahb_gates 44>;
- status = "disabled";
- };
-
- framebuffer@1 {
- compatible = "allwinner,simple-framebuffer",
- "simple-framebuffer";
- allwinner,pipeline = "de_be0-lcd0";
- clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
- <&ahb_gates 44>;
+ clocks = <&ccu CLK_AHB_LCD>, <&ccu CLK_AHB_HDMI>,
+ <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DRAM_DE_BE>,
+ <&ccu CLK_DE_BE>, <&ccu CLK_HDMI>;
status = "disabled";
};
+ };
- framebuffer@2 {
- compatible = "allwinner,simple-framebuffer",
- "simple-framebuffer";
- allwinner,pipeline = "de_be0-lcd0-tve0";
- clocks = <&pll3>, <&pll5 1>, <&ahb_gates 34>,
- <&ahb_gates 36>, <&ahb_gates 44>;
- status = "disabled";
- };
+ display-engine {
+ compatible = "allwinner,sun5i-a10s-display-engine";
+ allwinner,pipelines = <&fe0>;
};
- clocks {
- ahb_gates: clk@01c20060 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a10s-ahb-gates-clk";
- reg = <0x01c20060 0x8>;
- clocks = <&ahb>;
- clock-indices = <0>, <1>,
- <2>, <5>, <6>,
- <7>, <8>, <9>,
- <10>, <13>,
- <14>, <17>, <18>,
- <20>, <21>, <22>,
- <26>, <28>, <32>,
- <34>, <36>, <40>,
- <43>, <44>,
- <46>, <51>,
- <52>;
- clock-output-names = "ahb_usbotg", "ahb_ehci",
- "ahb_ohci", "ahb_ss", "ahb_dma",
- "ahb_bist", "ahb_mmc0", "ahb_mmc1",
- "ahb_mmc2", "ahb_nand",
- "ahb_sdram", "ahb_emac", "ahb_ts",
- "ahb_spi0", "ahb_spi1", "ahb_spi2",
- "ahb_gps", "ahb_stimer", "ahb_ve",
- "ahb_tve", "ahb_lcd", "ahb_csi",
- "ahb_hdmi", "ahb_de_be",
- "ahb_de_fe", "ahb_iep",
- "ahb_mali400";
- };
+ soc@1c00000 {
+ hdmi: hdmi@1c16000 {
+ compatible = "allwinner,sun5i-a10s-hdmi";
+ reg = <0x01c16000 0x1000>;
+ interrupts = <58>;
+ clocks = <&ccu CLK_AHB_HDMI>, <&ccu CLK_HDMI>,
+ <&ccu CLK_PLL_VIDEO0_2X>,
+ <&ccu CLK_PLL_VIDEO1_2X>;
+ clock-names = "ahb", "mod", "pll-0", "pll-1";
+ dmas = <&dma SUN4I_DMA_NORMAL 16>,
+ <&dma SUN4I_DMA_NORMAL 16>,
+ <&dma SUN4I_DMA_DEDICATED 24>;
+ dma-names = "ddc-tx", "ddc-rx", "audio-tx";
+ status = "disabled";
- apb0_gates: clk@01c20068 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a10s-apb0-gates-clk";
- reg = <0x01c20068 0x4>;
- clocks = <&apb0>;
- clock-indices = <0>, <3>,
- <5>, <6>,
- <10>;
- clock-output-names = "apb0_codec", "apb0_iis",
- "apb0_pio", "apb0_ir",
- "apb0_keypad";
- };
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
- apb1_gates: clk@01c2006c {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a10s-apb1-gates-clk";
- reg = <0x01c2006c 0x4>;
- clocks = <&apb1>;
- clock-indices = <0>, <1>,
- <2>, <16>,
- <17>, <18>,
- <19>;
- clock-output-names = "apb1_i2c0", "apb1_i2c1",
- "apb1_i2c2", "apb1_uart0",
- "apb1_uart1", "apb1_uart2",
- "apb1_uart3";
- };
- };
+ hdmi_in: port@0 {
+ reg = <0>;
- soc@01c00000 {
- emac: ethernet@01c0b000 {
- compatible = "allwinner,sun4i-a10-emac";
- reg = <0x01c0b000 0x1000>;
- interrupts = <55>;
- clocks = <&ahb_gates 17>;
- allwinner,sram = <&emac_sram 1>;
- status = "disabled";
- };
+ hdmi_in_tcon0: endpoint {
+ remote-endpoint = <&tcon0_out_hdmi>;
+ };
+ };
- mdio: mdio@01c0b080 {
- compatible = "allwinner,sun4i-a10-mdio";
- reg = <0x01c0b080 0x14>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
+ hdmi_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
};
- pwm: pwm@01c20e00 {
+ pwm: pwm@1c20e00 {
compatible = "allwinner,sun5i-a10s-pwm";
reg = <0x01c20e00 0xc>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_HOSC>;
#pwm-cells = <3>;
status = "disabled";
};
-
- uart0: serial@01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <1>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&apb1_gates 16>;
- status = "disabled";
- };
-
- uart2: serial@01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <3>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&apb1_gates 18>;
- status = "disabled";
- };
};
};
+&ccu {
+ compatible = "allwinner,sun5i-a10s-ccu";
+};
+
&pio {
compatible = "allwinner,sun5i-a10s-pinctrl";
uart0_pins_a: uart0@0 {
- allwinner,pins = "PB19", "PB20";
- allwinner,function = "uart0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB19", "PB20";
+ function = "uart0";
};
- uart2_pins_a: uart2@0 {
- allwinner,pins = "PC18", "PC19";
- allwinner,function = "uart2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart2_pins_b: uart2@1 {
+ pins = "PC18", "PC19";
+ function = "uart2";
};
- emac_pins_a: emac0@0 {
- allwinner,pins = "PA0", "PA1", "PA2",
+ emac_pins_b: emac0@1 {
+ pins = "PA0", "PA1", "PA2",
"PA3", "PA4", "PA5", "PA6",
"PA7", "PA8", "PA9", "PA10",
"PA11", "PA12", "PA13", "PA14",
"PA15", "PA16";
- allwinner,function = "emac";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- emac_pins_b: emac0@1 {
- allwinner,pins = "PD6", "PD7", "PD10",
- "PD11", "PD12", "PD13", "PD14",
- "PD15", "PD18", "PD19", "PD20",
- "PD21", "PD22", "PD23", "PD24",
- "PD25", "PD26", "PD27";
- allwinner,function = "emac";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ function = "emac";
};
mmc1_pins_a: mmc1@0 {
- allwinner,pins = "PG3", "PG4", "PG5",
+ pins = "PG3", "PG4", "PG5",
"PG6", "PG7", "PG8";
- allwinner,function = "mmc1";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ function = "mmc1";
+ drive-strength = <30>;
};
- spi2_pins_a: spi2@0 {
- allwinner,pins = "PB12", "PB13", "PB14";
- allwinner,function = "spi2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ spi2_pins_b: spi2@1 {
+ pins = "PB12", "PB13", "PB14";
+ function = "spi2";
};
- spi2_cs0_pins_a: spi2_cs0@0 {
- allwinner,pins = "PB11";
- allwinner,function = "spi2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ spi2_cs0_pins_b: spi2_cs0@1 {
+ pins = "PB11";
+ function = "spi2";
};
};
&sram_a {
- emac_sram: sram-section@8000 {
- compatible = "allwinner,sun4i-a10-sram-a3-a4";
- reg = <0x8000 0x4000>;
- status = "disabled";
+};
+
+&tcon0_out {
+ tcon0_out_hdmi: endpoint@2 {
+ reg = <2>;
+ remote-endpoint = <&hdmi_in_tcon0>;
+ allwinner,tcon-channel = <1>;
};
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/pwm/pwm.h>
/ {
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_d709>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
- cd-inverted;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
status = "okay";
};
&pio {
mmc0_cd_pin_d709: mmc0_cd_pin@0 {
- allwinner,pins = "PG0";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG0";
+ function = "gpio_in";
+ bias-pull-up;
};
usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ pins = "PG1";
+ function = "gpio_in";
+ bias-pull-down;
};
usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PG2";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG2";
+ function = "gpio_in";
+ bias-pull-up;
};
};
status = "okay";
};
-&usb0_vbus_pin_a {
- allwinner,pins = "PG12";
-};
-
&usbphy {
pinctrl-names = "default";
pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "HSG H702";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_h702>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
- cd-inverted;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
status = "okay";
};
&pio {
mmc0_cd_pin_h702: mmc0_cd_pin@0 {
- allwinner,pins = "PG0";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG0";
+ function = "gpio_in";
+ bias-pull-up;
};
usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PG2";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG2";
+ function = "gpio_in";
+ bias-pull-up;
};
usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PG1";
+ function = "gpio_in";
};
};
};
®_usb0_vbus {
- pinctrl-0 = <&usb0_vbus_pin_a>;
gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
status = "okay";
};
status = "okay";
};
-&usb0_vbus_pin_a {
- allwinner,pins = "PG12";
-};
-
&usbphy {
pinctrl-names = "default";
pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
/dts-v1/;
#include "sun5i-a13.dtsi"
-#include "sunxi-common-regulators.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "sun5i-reference-design-tablet.dtsi"
/ {
model = "INet-98V Rev 02";
compatible = "primux,inet98v-rev2", "allwinner,sun5i-a13";
-
- aliases {
- serial0 = &uart1;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
-};
-
-&cpu0 {
- cpu-supply = <®_dcdc2>;
-};
-
-&ehci0 {
- status = "okay";
-};
-
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- axp209: pmic@34 {
- reg = <0x34>;
- interrupts = <0>;
- };
-};
-
-#include "axp209.dtsi"
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
-
- pcf8563: rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-};
-
-&lradc {
- vref-supply = <®_ldo2>;
- status = "okay";
-
- button@200 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- channel = <0>;
- voltage = <200000>;
- };
-
- button@400 {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- channel = <0>;
- voltage = <400000>;
- };
-};
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_inet98fv2>;
- vmmc-supply = <®_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
- cd-inverted;
- status = "okay";
-};
-
-&otg_sram {
- status = "okay";
-};
-
-&pio {
- mmc0_cd_pin_inet98fv2: mmc0_cd_pin@0 {
- allwinner,pins = "PG0";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PG2";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-};
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1250000>;
- regulator-name = "vdd-int-pll";
-};
-
-®_ldo1 {
- regulator-name = "vdd-rtc";
-};
-
-®_ldo2 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "avcc";
-};
-
-®_ldo3 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
-};
-
-®_usb0_vbus {
- gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_b>;
- status = "okay";
-};
-
-&usb_otg {
- dr_mode = "otg";
- status = "okay";
-};
-
-&usb0_vbus_pin_a {
- allwinner,pins = "PG12";
-};
-
-&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
- usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
- usb0_vbus-supply = <®_usb0_vbus>;
- usb1_vbus-supply = <®_ldo3>;
- status = "okay";
};
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Olimex A13-Olinuxino Micro";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxinom>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
- cd-inverted;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
status = "okay";
};
&pio {
mmc0_cd_pin_olinuxinom: mmc0_cd_pin@0 {
- allwinner,pins = "PG0";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG0";
+ function = "gpio_in";
+ bias-pull-up;
};
led_pins_olinuxinom: led_pins@0 {
- allwinner,pins = "PG9";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_20_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PG9";
+ function = "gpio_out";
+ drive-strength = <20>;
};
usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PG2";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG2";
+ function = "gpio_in";
+ bias-pull-up;
};
usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ pins = "PG1";
+ function = "gpio_in";
+ bias-pull-down;
};
usb0_vbus_pin_olinuxinom: usb0_vbus_pin@0 {
- allwinner,pins = "PG12";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PG12";
+ function = "gpio_out";
};
usb1_vbus_pin_olinuxinom: usb1_vbus_pin@0 {
- allwinner,pins = "PG11";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PG11";
+ function = "gpio_out";
};
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Olimex A13-Olinuxino";
default-state = "on";
};
};
+
+ bridge {
+ compatible = "dumb-vga-dac";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ vga_bridge_in: endpoint {
+ remote-endpoint = <&tcon0_out_vga>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ vga_bridge_out: endpoint {
+ remote-endpoint = <&vga_con_in>;
+ };
+ };
+ };
+ };
+
+ vga {
+ compatible = "vga-connector";
+
+ port {
+ vga_con_in: endpoint {
+ remote-endpoint = <&vga_bridge_out>;
+ };
+ };
+ };
+};
+
+&be0 {
+ status = "okay";
+};
+
+&codec {
+ status = "okay";
};
&ehci0 {
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
- cd-inverted;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
status = "okay";
};
&pio {
mmc0_cd_pin_olinuxino: mmc0_cd_pin@0 {
- allwinner,pins = "PG0";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG0";
+ function = "gpio_in";
+ bias-pull-up;
};
led_pins_olinuxino: led_pins@0 {
- allwinner,pins = "PG9";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_20_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PG9";
+ function = "gpio_out";
+ drive-strength = <20>;
};
usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PG2";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG2";
+ function = "gpio_in";
+ bias-pull-up;
};
usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ pins = "PG1";
+ function = "gpio_in";
+ bias-pull-down;
};
usb1_vbus_pin_olinuxino: usb1_vbus_pin@0 {
- allwinner,pins = "PG11";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PG11";
+ function = "gpio_out";
};
};
status = "okay";
};
+&tcon0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_rgb666_pins>;
+ status = "okay";
+};
+
+&tcon0_out {
+ tcon0_out_vga: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&vga_bridge_in>;
+ };
+};
+
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins_b>;
status = "okay";
};
-&usb0_vbus_pin_a {
- allwinner,pins = "PG12";
-};
-
&usbphy {
pinctrl-names = "default";
pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
};
&codec_pa_pin {
- allwinner,pins = "PG3";
-};
-
-&i2c1 {
- icn8318: touchscreen@40 {
- compatible = "chipone,icn8318";
- reg = <0x40>;
- interrupt-parent = <&pio>;
- interrupts = <6 9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
- pinctrl-names = "default";
- pinctrl-0 = <&ts_wake_pin_p66>;
- wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
- touchscreen-size-x = <800>;
- touchscreen-size-y = <480>;
- touchscreen-inverted-x;
- touchscreen-swapped-x-y;
- };
+ pins = "PG3";
};
&mmc2 {
&pio {
i2c_lcd_pins: i2c_lcd_pin@0 {
- allwinner,pins = "PG10", "PG12";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- ts_wake_pin_p66: ts_wake_pin@0 {
- allwinner,pins = "PB3";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PG10", "PG12";
+ function = "gpio_out";
+ bias-pull-up;
};
-
};
®_usb0_vbus {
gpio = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
};
+&touchscreen {
+ compatible = "chipone,icn8318";
+ reg = <0x40>;
+ /* The P66 uses a different EINT then the reference design */
+ interrupts = <6 9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
+ /* The icn8318 binding expects wake-gpios instead of power-gpios */
+ wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ touchscreen-inverted-x;
+ touchscreen-swapped-x-y;
+ status = "okay";
+};
+
&uart1 {
/* The P66 uses the uart pins as gpios */
status = "disabled";
};
&usb0_vbus_pin_a {
- allwinner,pins = "PB4";
+ pins = "PB4";
};
#include "sun5i.dtsi"
-#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/thermal/thermal.h>
/ {
interrupt-parent = <&intc>;
- chosen {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- framebuffer@0 {
- compatible = "allwinner,simple-framebuffer",
- "simple-framebuffer";
- allwinner,pipeline = "de_be0-lcd0";
- clocks = <&ahb_gates 36>, <&ahb_gates 44>, <&de_be_clk>,
- <&tcon_ch0_clk>, <&dram_gates 26>;
- status = "disabled";
- };
- };
-
thermal-zones {
cpu_thermal {
/* milliseconds */
trips {
cpu_alert0: cpu_alert0 {
/* milliCelsius */
- temperature = <850000>;
+ temperature = <85000>;
hysteresis = <2000>;
type = "passive";
};
};
};
- clocks {
- ahb_gates: clk@01c20060 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-ahb-gates-clk";
- reg = <0x01c20060 0x8>;
- clocks = <&ahb>;
- clock-indices = <0>, <1>,
- <2>, <5>, <6>,
- <7>, <8>, <9>,
- <10>, <13>,
- <14>, <20>,
- <21>, <22>,
- <28>, <32>, <34>,
- <36>, <40>, <44>,
- <46>, <51>,
- <52>;
- clock-output-names = "ahb_usbotg", "ahb_ehci",
- "ahb_ohci", "ahb_ss", "ahb_dma",
- "ahb_bist", "ahb_mmc0", "ahb_mmc1",
- "ahb_mmc2", "ahb_nand",
- "ahb_sdram", "ahb_spi0",
- "ahb_spi1", "ahb_spi2",
- "ahb_stimer", "ahb_ve", "ahb_tve",
- "ahb_lcd", "ahb_csi", "ahb_de_be",
- "ahb_de_fe", "ahb_iep",
- "ahb_mali400";
- };
-
- apb0_gates: clk@01c20068 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-apb0-gates-clk";
- reg = <0x01c20068 0x4>;
- clocks = <&apb0>;
- clock-indices = <0>, <5>,
- <6>;
- clock-output-names = "apb0_codec", "apb0_pio",
- "apb0_ir";
- };
-
- apb1_gates: clk@01c2006c {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-apb1-gates-clk";
- reg = <0x01c2006c 0x4>;
- clocks = <&apb1>;
- clock-indices = <0>, <1>,
- <2>, <17>,
- <19>;
- clock-output-names = "apb1_i2c0", "apb1_i2c1",
- "apb1_i2c2", "apb1_uart1",
- "apb1_uart3";
- };
-
- dram_gates: clk@01c20100 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-dram-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01c20100 0x4>;
- clocks = <&pll5 0>;
- clock-indices = <0>,
- <1>,
- <25>,
- <26>,
- <29>,
- <31>;
- clock-output-names = "dram_ve",
- "dram_csi",
- "dram_de_fe",
- "dram_de_be",
- "dram_ace",
- "dram_iep";
- };
-
- de_be_clk: clk@01c20104 {
- #clock-cells = <0>;
- #reset-cells = <0>;
- compatible = "allwinner,sun4i-a10-display-clk";
- reg = <0x01c20104 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll5 1>;
- clock-output-names = "de-be";
- };
-
- de_fe_clk: clk@01c2010c {
- #clock-cells = <0>;
- #reset-cells = <0>;
- compatible = "allwinner,sun4i-a10-display-clk";
- reg = <0x01c2010c 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll5 1>;
- clock-output-names = "de-fe";
- };
-
- tcon_ch0_clk: clk@01c20118 {
- #clock-cells = <0>;
- #reset-cells = <1>;
- compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
- reg = <0x01c20118 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
- clock-output-names = "tcon-ch0-sclk";
- };
-
- tcon_ch1_clk: clk@01c2012c {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
- reg = <0x01c2012c 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
- clock-output-names = "tcon-ch1-sclk";
- };
- };
-
display-engine {
compatible = "allwinner,sun5i-a13-display-engine";
allwinner,pipelines = <&fe0>;
};
- soc@01c00000 {
- tcon0: lcd-controller@01c0c000 {
- compatible = "allwinner,sun5i-a13-tcon";
- reg = <0x01c0c000 0x1000>;
- interrupts = <44>;
- resets = <&tcon_ch0_clk 1>;
- reset-names = "lcd";
- clocks = <&ahb_gates 36>,
- <&tcon_ch0_clk>,
- <&tcon_ch1_clk>;
- clock-names = "ahb",
- "tcon-ch0",
- "tcon-ch1";
- clock-output-names = "tcon-pixel-clock";
- status = "disabled";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- tcon0_in: port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- tcon0_in_be0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&be0_out_tcon0>;
- };
- };
-
- tcon0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
- };
- };
- };
-
- pwm: pwm@01c20e00 {
+ soc@1c00000 {
+ pwm: pwm@1c20e00 {
compatible = "allwinner,sun5i-a13-pwm";
reg = <0x01c20e00 0xc>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_HOSC>;
#pwm-cells = <3>;
status = "disabled";
};
- fe0: display-frontend@01e00000 {
- compatible = "allwinner,sun5i-a13-display-frontend";
- reg = <0x01e00000 0x20000>;
- interrupts = <47>;
- clocks = <&ahb_gates 46>, <&de_fe_clk>,
- <&dram_gates 25>;
- clock-names = "ahb", "mod",
- "ram";
- resets = <&de_fe_clk>;
- status = "disabled";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- fe0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- fe0_out_be0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&be0_in_fe0>;
- };
- };
- };
- };
-
- be0: display-backend@01e60000 {
- compatible = "allwinner,sun5i-a13-display-backend";
- reg = <0x01e60000 0x10000>;
- clocks = <&ahb_gates 44>, <&de_be_clk>,
- <&dram_gates 26>;
- clock-names = "ahb", "mod",
- "ram";
- resets = <&de_be_clk>;
- status = "disabled";
-
- assigned-clocks = <&de_be_clk>;
- assigned-clock-rates = <300000000>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- be0_in: port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- be0_in_fe0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&fe0_out_be0>;
- };
- };
-
- be0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- be0_out_tcon0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&tcon0_in_be0>;
- };
- };
- };
- };
};
};
+&ccu {
+ compatible = "allwinner,sun5i-a13-ccu";
+};
+
&cpu0 {
clock-latency = <244144>; /* 8 32k periods */
operating-points = <
432000 1200000
>;
#cooling-cells = <2>;
- cooling-min-level = <0>;
- cooling-max-level = <5>;
};
&pio {
compatible = "allwinner,sun5i-a13-pinctrl";
-
- lcd_rgb666_pins: lcd_rgb666@0 {
- allwinner,pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
- "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
- "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
- "PD24", "PD25", "PD26", "PD27";
- allwinner,function = "lcd0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- uart1_pins_a: uart1@0 {
- allwinner,pins = "PE10", "PE11";
- allwinner,function = "uart1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- uart1_pins_b: uart1@1 {
- allwinner,pins = "PG3", "PG4";
- allwinner,function = "uart1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
};
&pio {
usb0_id_pin_chip_pro: usb0-id-pin@0 {
- allwinner,pins = "PG2";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PG2";
+ function = "gpio_in";
};
wifi_reg_on_pin_chip_pro: wifi-reg-on-pin@0 {
- allwinner,pins = "PB10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB10";
+ function = "gpio_out";
};
};
&pwm {
pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins_a>, <&pwm1_pins>;
+ pinctrl-0 = <&pwm0_pins>, <&pwm1_pins>;
status = "disabled";
};
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_a>, <&uart1_cts_rts_pins_a>;
+ pinctrl-0 = <&uart1_pins_b>, <&uart1_cts_rts_pins_a>;
status = "okay";
};
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include <dt-bindings/clock/sun4i-a10-pll2.h>
+#include "sun5i.dtsi"
+
+#include <dt-bindings/clock/sun5i-ccu.h>
#include <dt-bindings/dma/sun4i-a10.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sun5i-ccu.h>
/ {
- interrupt-parent = <&intc>;
- #address-cells = <1>;
- #size-cells = <1>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: cpu@0 {
- device_type = "cpu";
- compatible = "arm,cortex-a8";
- reg = <0x0>;
- clocks = <&cpu>;
- };
- };
-
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- /*
- * This is a dummy clock, to be used as placeholder on
- * other mux clocks when a specific parent clock is not
- * yet implemented. It should be dropped when the driver
- * is complete.
- */
- dummy: dummy {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <0>;
- };
-
- osc24M: clk@01c20050 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-osc-clk";
- reg = <0x01c20050 0x4>;
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc3M: osc3M-clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <8>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "osc3M";
- };
-
- osc32k: clk@0 {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- pll1: clk@01c20000 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll1-clk";
- reg = <0x01c20000 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll1";
- };
-
- pll2: clk@01c20008 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-pll2-clk";
- reg = <0x01c20008 0x8>;
- clocks = <&osc24M>;
- clock-output-names = "pll2-1x", "pll2-2x",
- "pll2-4x", "pll2-8x";
- };
-
- pll3: clk@01c20010 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll3-clk";
- reg = <0x01c20010 0x4>;
- clocks = <&osc3M>;
- clock-output-names = "pll3";
- };
-
- pll3x2: pll3x2-clk {
- compatible = "allwinner,sun4i-a10-pll3-2x-clk";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <2>;
- clocks = <&pll3>;
- clock-output-names = "pll3-2x";
- };
-
- pll4: clk@01c20018 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll1-clk";
- reg = <0x01c20018 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll4";
- };
-
- pll5: clk@01c20020 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-pll5-clk";
- reg = <0x01c20020 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll5_ddr", "pll5_other";
- };
-
- pll6: clk@01c20028 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-pll6-clk";
- reg = <0x01c20028 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll6_sata", "pll6_other", "pll6";
- };
-
- pll7: clk@01c20030 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll3-clk";
- reg = <0x01c20030 0x4>;
- clocks = <&osc3M>;
- clock-output-names = "pll7";
- };
-
- pll7x2: pll7x2-clk {
- compatible = "allwinner,sun4i-a10-pll3-2x-clk";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <2>;
- clocks = <&pll7>;
- clock-output-names = "pll7-2x";
- };
-
- /* dummy is 200M */
- cpu: cpu@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-cpu-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>;
- clock-output-names = "cpu";
- };
-
- axi: axi@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-axi-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&cpu>;
- clock-output-names = "axi";
- };
-
- ahb: ahb@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun5i-a13-ahb-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&axi>, <&cpu>, <&pll6 1>;
- clock-output-names = "ahb";
- /*
- * Use PLL6 as parent, instead of CPU/AXI
- * which has rate changes due to cpufreq
- */
- assigned-clocks = <&ahb>;
- assigned-clock-parents = <&pll6 1>;
- };
-
- apb0: apb0@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb0-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&ahb>;
- clock-output-names = "apb0";
- };
-
- apb1: clk@01c20058 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb1-clk";
- reg = <0x01c20058 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&osc32k>;
- clock-output-names = "apb1";
- };
-
- axi_gates: clk@01c2005c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-gates-clk";
- reg = <0x01c2005c 0x4>;
- clocks = <&axi>;
- clock-indices = <0>;
- clock-output-names = "axi_dram";
- };
-
- ahb_gates: clk@01c20060 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-ahb-gates-clk";
- reg = <0x01c20060 0x8>;
- clocks = <&ahb>;
- clock-indices = <0>, <1>,
- <2>, <5>, <6>,
- <7>, <8>, <9>,
- <10>, <13>,
- <14>, <17>, <20>,
- <21>, <22>,
- <28>, <32>, <34>,
- <36>, <40>, <44>,
- <46>, <51>,
- <52>;
- clock-output-names = "ahb_usbotg", "ahb_ehci",
- "ahb_ohci", "ahb_ss", "ahb_dma",
- "ahb_bist", "ahb_mmc0", "ahb_mmc1",
- "ahb_mmc2", "ahb_nand",
- "ahb_sdram", "ahb_emac", "ahb_spi0",
- "ahb_spi1", "ahb_spi2",
- "ahb_hstimer", "ahb_ve", "ahb_tve",
- "ahb_lcd", "ahb_csi", "ahb_de_be",
- "ahb_de_fe", "ahb_iep",
- "ahb_mali400";
- };
-
- apb0_gates: clk@01c20068 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-gates-clk";
- reg = <0x01c20068 0x4>;
- clocks = <&apb0>;
- clock-indices = <0>, <3>,
- <5>, <6>;
- clock-output-names = "apb0_codec", "apb0_i2s0",
- "apb0_pio", "apb0_ir";
- };
-
- apb1_gates: clk@01c2006c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-gates-clk";
- reg = <0x01c2006c 0x4>;
- clocks = <&apb1>;
- clock-indices = <0>, <1>,
- <2>, <17>,
- <18>, <19>;
- clock-output-names = "apb1_i2c0", "apb1_i2c1",
- "apb1_i2c2", "apb1_uart1",
- "apb1_uart2", "apb1_uart3";
- };
-
- nand_clk: clk@01c20080 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20080 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "nand";
- };
-
- ms_clk: clk@01c20084 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20084 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ms";
- };
-
- mmc0_clk: clk@01c20088 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20088 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc0",
- "mmc0_output",
- "mmc0_sample";
- };
-
- mmc1_clk: clk@01c2008c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c2008c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc1",
- "mmc1_output",
- "mmc1_sample";
- };
-
- mmc2_clk: clk@01c20090 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20090 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc2",
- "mmc2_output",
- "mmc2_sample";
- };
-
- ts_clk: clk@01c20098 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20098 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ts";
- };
-
- ss_clk: clk@01c2009c {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c2009c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ss";
- };
-
- spi0_clk: clk@01c200a0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a0 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi0";
- };
-
- spi1_clk: clk@01c200a4 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a4 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi1";
- };
-
- spi2_clk: clk@01c200a8 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a8 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi2";
- };
-
- ir0_clk: clk@01c200b0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200b0 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ir0";
- };
-
- i2s0_clk: clk@01c200b8 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod1-clk";
- reg = <0x01c200b8 0x4>;
- clocks = <&pll2 SUN4I_A10_PLL2_8X>,
- <&pll2 SUN4I_A10_PLL2_4X>,
- <&pll2 SUN4I_A10_PLL2_2X>,
- <&pll2 SUN4I_A10_PLL2_1X>;
- clock-output-names = "i2s0";
- };
-
- spdif_clk: clk@01c200c0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod1-clk";
- reg = <0x01c200c0 0x4>;
- clocks = <&pll2 SUN4I_A10_PLL2_8X>,
- <&pll2 SUN4I_A10_PLL2_4X>,
- <&pll2 SUN4I_A10_PLL2_2X>,
- <&pll2 SUN4I_A10_PLL2_1X>;
- clock-output-names = "spdif";
- };
-
- usb_clk: clk@01c200cc {
- #clock-cells = <1>;
- #reset-cells = <1>;
- compatible = "allwinner,sun5i-a13-usb-clk";
- reg = <0x01c200cc 0x4>;
- clocks = <&pll6 1>;
- clock-output-names = "usb_ohci0", "usb_phy";
- };
-
- dram_gates: clk@01c20100 {
- #clock-cells = <1>;
- compatible = "nextthing,gr8-dram-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01c20100 0x4>;
- clocks = <&pll5 0>;
- clock-indices = <0>,
- <1>,
- <25>,
- <26>,
- <29>,
- <31>;
- clock-output-names = "dram_ve",
- "dram_csi",
- "dram_de_fe",
- "dram_de_be",
- "dram_ace",
- "dram_iep";
- };
-
- de_be_clk: clk@01c20104 {
- #clock-cells = <0>;
- #reset-cells = <0>;
- compatible = "allwinner,sun4i-a10-display-clk";
- reg = <0x01c20104 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll5 1>;
- clock-output-names = "de-be";
- };
-
- de_fe_clk: clk@01c2010c {
- #clock-cells = <0>;
- #reset-cells = <0>;
- compatible = "allwinner,sun4i-a10-display-clk";
- reg = <0x01c2010c 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll5 1>;
- clock-output-names = "de-fe";
- };
-
- tcon_ch0_clk: clk@01c20118 {
- #clock-cells = <0>;
- #reset-cells = <1>;
- compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
- reg = <0x01c20118 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
- clock-output-names = "tcon-ch0-sclk";
- };
-
- tcon_ch1_clk: clk@01c2012c {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
- reg = <0x01c2012c 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
- clock-output-names = "tcon-ch1-sclk";
- };
-
- codec_clk: clk@01c20140 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-codec-clk";
- reg = <0x01c20140 0x4>;
- clocks = <&pll2 SUN4I_A10_PLL2_1X>;
- clock-output-names = "codec";
- };
-
- mbus_clk: clk@01c2015c {
- #clock-cells = <0>;
- compatible = "allwinner,sun5i-a13-mbus-clk";
- reg = <0x01c2015c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mbus";
- };
- };
-
display-engine {
compatible = "allwinner,sun5i-a13-display-engine";
allwinner,pipelines = <&fe0>;
};
- soc@01c00000 {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- sram-controller@01c00000 {
- compatible = "allwinner,sun4i-a10-sram-controller";
- reg = <0x01c00000 0x30>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- sram_a: sram@00000000 {
- compatible = "mmio-sram";
- reg = <0x00000000 0xc000>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0 0x00000000 0xc000>;
- };
-
- sram_d: sram@00010000 {
- compatible = "mmio-sram";
- reg = <0x00010000 0x1000>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0 0x00010000 0x1000>;
-
- otg_sram: sram-section@0000 {
- compatible = "allwinner,sun4i-a10-sram-d";
- reg = <0x0000 0x1000>;
- status = "disabled";
- };
- };
- };
-
- dma: dma-controller@01c02000 {
- compatible = "allwinner,sun4i-a10-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <27>;
- clocks = <&ahb_gates 6>;
- #dma-cells = <2>;
- };
-
- nfc: nand@01c03000 {
- compatible = "allwinner,sun4i-a10-nand";
- reg = <0x01c03000 0x1000>;
- interrupts = <37>;
- clocks = <&ahb_gates 13>, <&nand_clk>;
- clock-names = "ahb", "mod";
- dmas = <&dma SUN4I_DMA_DEDICATED 3>;
- dma-names = "rxtx";
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi0: spi@01c05000 {
- compatible = "allwinner,sun4i-a10-spi";
- reg = <0x01c05000 0x1000>;
- interrupts = <10>;
- clocks = <&ahb_gates 20>, <&spi0_clk>;
- clock-names = "ahb", "mod";
- dmas = <&dma SUN4I_DMA_DEDICATED 27>,
- <&dma SUN4I_DMA_DEDICATED 26>;
- dma-names = "rx", "tx";
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi1: spi@01c06000 {
- compatible = "allwinner,sun4i-a10-spi";
- reg = <0x01c06000 0x1000>;
- interrupts = <11>;
- clocks = <&ahb_gates 21>, <&spi1_clk>;
- clock-names = "ahb", "mod";
- dmas = <&dma SUN4I_DMA_DEDICATED 9>,
- <&dma SUN4I_DMA_DEDICATED 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- tve0: tv-encoder@01c0a000 {
- compatible = "allwinner,sun4i-a10-tv-encoder";
- reg = <0x01c0a000 0x1000>;
- clocks = <&ahb_gates 34>;
- resets = <&tcon_ch0_clk 0>;
- status = "disabled";
-
- port {
- #address-cells = <1>;
- #size-cells = <0>;
-
- tve0_in_tcon0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&tcon0_out_tve0>;
- };
- };
- };
-
- tcon0: lcd-controller@01c0c000 {
- compatible = "allwinner,sun5i-a13-tcon";
- reg = <0x01c0c000 0x1000>;
- interrupts = <44>;
- resets = <&tcon_ch0_clk 1>;
- reset-names = "lcd";
- clocks = <&ahb_gates 36>,
- <&tcon_ch0_clk>,
- <&tcon_ch1_clk>;
- clock-names = "ahb",
- "tcon-ch0",
- "tcon-ch1";
- clock-output-names = "tcon-pixel-clock";
- status = "disabled";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- tcon0_in: port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- tcon0_in_be0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&be0_out_tcon0>;
- };
- };
-
- tcon0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- tcon0_out_tve0: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&tve0_in_tcon0>;
- };
- };
- };
- };
-
- mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun5i-a13-mmc";
- reg = <0x01c0f000 0x1000>;
- clocks = <&ahb_gates 8>,
- <&mmc0_clk 0>,
- <&mmc0_clk 1>,
- <&mmc0_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- interrupts = <32>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc1: mmc@01c10000 {
- compatible = "allwinner,sun5i-a13-mmc";
- reg = <0x01c10000 0x1000>;
- clocks = <&ahb_gates 9>,
- <&mmc1_clk 0>,
- <&mmc1_clk 1>,
- <&mmc1_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- interrupts = <33>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc2: mmc@01c11000 {
- compatible = "allwinner,sun5i-a13-mmc";
- reg = <0x01c11000 0x1000>;
- clocks = <&ahb_gates 10>,
- <&mmc2_clk 0>,
- <&mmc2_clk 1>,
- <&mmc2_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- interrupts = <34>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usb_otg: usb@01c13000 {
- compatible = "allwinner,sun4i-a10-musb";
- reg = <0x01c13000 0x0400>;
- clocks = <&ahb_gates 0>;
- interrupts = <38>;
- interrupt-names = "mc";
- phys = <&usbphy 0>;
- phy-names = "usb";
- extcon = <&usbphy 0>;
- allwinner,sram = <&otg_sram 1>;
- status = "disabled";
-
- dr_mode = "otg";
- };
-
- usbphy: phy@01c13400 {
- #phy-cells = <1>;
- compatible = "allwinner,sun5i-a13-usb-phy";
- reg = <0x01c13400 0x10 0x01c14800 0x4>;
- reg-names = "phy_ctrl", "pmu1";
- clocks = <&usb_clk 8>;
- clock-names = "usb_phy";
- resets = <&usb_clk 0>, <&usb_clk 1>;
- reset-names = "usb0_reset", "usb1_reset";
- status = "disabled";
- };
-
- ehci0: usb@01c14000 {
- compatible = "allwinner,sun5i-a13-ehci", "generic-ehci";
- reg = <0x01c14000 0x100>;
- interrupts = <39>;
- clocks = <&ahb_gates 1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci0: usb@01c14400 {
- compatible = "allwinner,sun5i-a13-ohci", "generic-ohci";
- reg = <0x01c14400 0x100>;
- interrupts = <40>;
- clocks = <&usb_clk 6>, <&ahb_gates 2>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- spi2: spi@01c17000 {
- compatible = "allwinner,sun4i-a10-spi";
- reg = <0x01c17000 0x1000>;
- interrupts = <12>;
- clocks = <&ahb_gates 22>, <&spi2_clk>;
- clock-names = "ahb", "mod";
- dmas = <&dma SUN4I_DMA_DEDICATED 29>,
- <&dma SUN4I_DMA_DEDICATED 28>;
- dma-names = "rx", "tx";
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- intc: interrupt-controller@01c20400 {
- compatible = "allwinner,sun4i-a10-ic";
- reg = <0x01c20400 0x400>;
- interrupt-controller;
- #interrupt-cells = <1>;
- };
-
- pio: pinctrl@01c20800 {
- compatible = "nextthing,gr8-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <28>;
- clocks = <&apb0_gates 5>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <3>;
- #gpio-cells = <3>;
-
- i2c0_pins_a: i2c0@0 {
- allwinner,pins = "PB0", "PB1";
- allwinner,function = "i2c0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- i2c1_pins_a: i2c1@0 {
- allwinner,pins = "PB15", "PB16";
- allwinner,function = "i2c1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- i2c2_pins_a: i2c2@0 {
- allwinner,pins = "PB17", "PB18";
- allwinner,function = "i2c2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- i2s0_data_pins_a: i2s0-data@0 {
- allwinner,pins = "PB6", "PB7", "PB8", "PB9";
- allwinner,function = "i2s0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- i2s0_mclk_pins_a: i2s0-mclk@0 {
- allwinner,pins = "PB5";
- allwinner,function = "i2s0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- ir0_rx_pins_a: ir0@0 {
- allwinner,pins = "PB4";
- allwinner,function = "ir0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- lcd_rgb666_pins: lcd-rgb666@0 {
- allwinner,pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
- "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
- "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
- "PD24", "PD25", "PD26", "PD27";
- allwinner,function = "lcd0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc0_pins_a: mmc0@0 {
- allwinner,pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- allwinner,function = "mmc0";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- nand_pins_a: nand-base0@0 {
- allwinner,pins = "PC0", "PC1", "PC2",
- "PC5", "PC8", "PC9", "PC10",
- "PC11", "PC12", "PC13", "PC14",
- "PC15";
- allwinner,function = "nand0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- nand_cs0_pins_a: nand-cs@0 {
- allwinner,pins = "PC4";
- allwinner,function = "nand0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- nand_rb0_pins_a: nand-rb@0 {
- allwinner,pins = "PC6";
- allwinner,function = "nand0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- pwm0_pins_a: pwm0@0 {
- allwinner,pins = "PB2";
- allwinner,function = "pwm0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- pwm1_pins: pwm1 {
- allwinner,pins = "PG13";
- allwinner,function = "pwm1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- spdif_tx_pins_a: spdif@0 {
- allwinner,pins = "PB10";
- allwinner,function = "spdif";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- uart1_pins_a: uart1@1 {
- allwinner,pins = "PG3", "PG4";
- allwinner,function = "uart1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- uart1_cts_rts_pins_a: uart1-cts-rts@0 {
- allwinner,pins = "PG5", "PG6";
- allwinner,function = "uart1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- uart2_pins_a: uart2@1 {
- allwinner,pins = "PD2", "PD3";
- allwinner,function = "uart2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- uart2_cts_rts_pins_a: uart2-cts-rts@0 {
- allwinner,pins = "PD4", "PD5";
- allwinner,function = "uart2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- uart3_pins_a: uart3@1 {
- allwinner,pins = "PG9", "PG10";
- allwinner,function = "uart3";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- uart3_cts_rts_pins_a: uart3-cts-rts@0 {
- allwinner,pins = "PG11", "PG12";
- allwinner,function = "uart3";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
- };
-
- pwm: pwm@01c20e00 {
+ soc@1c00000 {
+ pwm: pwm@1c20e00 {
compatible = "allwinner,sun5i-a10s-pwm";
reg = <0x01c20e00 0xc>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_HOSC>;
#pwm-cells = <3>;
status = "disabled";
};
- timer@01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x01c20c00 0x90>;
- interrupts = <22>;
- clocks = <&osc24M>;
- };
-
- wdt: watchdog@01c20c90 {
- compatible = "allwinner,sun4i-a10-wdt";
- reg = <0x01c20c90 0x10>;
- };
-
- spdif: spdif@01c21000 {
+ spdif: spdif@1c21000 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun4i-a10-spdif";
reg = <0x01c21000 0x400>;
interrupts = <13>;
- clocks = <&apb0_gates 1>, <&spdif_clk>;
+ clocks = <&ccu CLK_APB0_SPDIF>, <&ccu CLK_SPDIF>;
clock-names = "apb", "spdif";
dmas = <&dma SUN4I_DMA_NORMAL 2>,
<&dma SUN4I_DMA_NORMAL 2>;
status = "disabled";
};
- ir0: ir@01c21800 {
- compatible = "allwinner,sun4i-a10-ir";
- clocks = <&apb0_gates 6>, <&ir0_clk>;
- clock-names = "apb", "ir";
- interrupts = <5>;
- reg = <0x01c21800 0x40>;
- status = "disabled";
- };
-
- i2s0: i2s@01c22400 {
+ i2s0: i2s@1c22400 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun4i-a10-i2s";
reg = <0x01c22400 0x400>;
interrupts = <16>;
- clocks = <&apb0_gates 3>, <&i2s0_clk>;
+ clocks = <&ccu CLK_APB0_I2S>, <&ccu CLK_I2S>;
clock-names = "apb", "mod";
dmas = <&dma SUN4I_DMA_NORMAL 3>,
<&dma SUN4I_DMA_NORMAL 3>;
dma-names = "rx", "tx";
status = "disabled";
};
+ };
+};
- lradc: lradc@01c22800 {
- compatible = "allwinner,sun4i-a10-lradc-keys";
- reg = <0x01c22800 0x100>;
- interrupts = <31>;
- status = "disabled";
- };
-
- codec: codec@01c22c00 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun4i-a10-codec";
- reg = <0x01c22c00 0x40>;
- interrupts = <30>;
- clocks = <&apb0_gates 0>, <&codec_clk>;
- clock-names = "apb", "codec";
- dmas = <&dma SUN4I_DMA_NORMAL 19>,
- <&dma SUN4I_DMA_NORMAL 19>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- rtp: rtp@01c25000 {
- compatible = "allwinner,sun5i-a13-ts";
- reg = <0x01c25000 0x100>;
- interrupts = <29>;
- #thermal-sensor-cells = <0>;
- };
-
- uart1: serial@01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <2>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&apb1_gates 17>;
- status = "disabled";
- };
-
- uart2: serial@01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <3>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&apb1_gates 18>;
- status = "disabled";
- };
-
- uart3: serial@01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <4>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&apb1_gates 19>;
- status = "disabled";
- };
-
- i2c0: i2c@01c2ac00 {
- compatible = "allwinner,sun4i-a10-i2c";
- reg = <0x01c2ac00 0x400>;
- interrupts = <7>;
- clocks = <&apb1_gates 0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c@01c2b000 {
- compatible = "allwinner,sun4i-a10-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <8>;
- clocks = <&apb1_gates 1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c@01c2b400 {
- compatible = "allwinner,sun4i-a10-i2c";
- reg = <0x01c2b400 0x400>;
- interrupts = <9>;
- clocks = <&apb1_gates 2>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- timer@01c60000 {
- compatible = "allwinner,sun5i-a13-hstimer";
- reg = <0x01c60000 0x1000>;
- interrupts = <82>, <83>;
- clocks = <&ahb_gates 28>;
- };
-
- fe0: display-frontend@01e00000 {
- compatible = "allwinner,sun5i-a13-display-frontend";
- reg = <0x01e00000 0x20000>;
- interrupts = <47>;
- clocks = <&ahb_gates 46>, <&de_fe_clk>,
- <&dram_gates 25>;
- clock-names = "ahb", "mod",
- "ram";
- resets = <&de_fe_clk>;
- status = "disabled";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- fe0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- fe0_out_be0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&be0_in_fe0>;
- };
- };
- };
- };
-
- be0: display-backend@01e60000 {
- compatible = "allwinner,sun5i-a13-display-backend";
- reg = <0x01e60000 0x10000>;
- clocks = <&ahb_gates 44>, <&de_be_clk>,
- <&dram_gates 26>;
- clock-names = "ahb", "mod",
- "ram";
- resets = <&de_be_clk>;
- status = "disabled";
+&ccu {
+ compatible = "nextthing,gr8-ccu";
+};
- assigned-clocks = <&de_be_clk>;
- assigned-clock-rates = <300000000>;
+&pio {
+ compatible = "nextthing,gr8-pinctrl";
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
+ i2s0_data_pins_a: i2s0-data@0 {
+ pins = "PB6", "PB7", "PB8", "PB9";
+ function = "i2s0";
+ };
- be0_in: port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
+ i2s0_mclk_pins_a: i2s0-mclk@0 {
+ pins = "PB5";
+ function = "i2s0";
+ };
- be0_in_fe0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&fe0_out_be0>;
- };
- };
+ pwm1_pins: pwm1 {
+ pins = "PG13";
+ function = "pwm1";
+ };
- be0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
+ spdif_tx_pins_a: spdif@0 {
+ pins = "PB10";
+ function = "spdif";
+ bias-pull-up;
+ };
- be0_out_tcon0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&tcon0_in_be0>;
- };
- };
- };
- };
+ uart1_cts_rts_pins_a: uart1-cts-rts@0 {
+ pins = "PG5", "PG6";
+ function = "uart1";
};
};
aliases {
i2c0 = &i2c0;
+ i2c1 = &i2c1;
i2c2 = &i2c2;
serial0 = &uart1;
serial1 = &uart3;
+ spi0 = &spi2;
};
chosen {
stdout-path = "serial0:115200n8";
};
- wifi_reg_on: wifi_reg_on {
- compatible = "regulator-fixed";
+ leds {
+ compatible = "gpio-leds";
+
+ status {
+ label = "chip:white:status";
+ gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ mmc0_pwrseq: mmc0_pwrseq {
+ compatible = "mmc-pwrseq-simple";
pinctrl-names = "default";
pinctrl-0 = <&chip_wifi_reg_on_pin>;
+ reset-gpios = <&pio 2 19 GPIO_ACTIVE_LOW>; /* PC19 */
+ };
- regulator-name = "wifi-reg-on";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&pio 2 19 GPIO_ACTIVE_HIGH>; /* PC19 */
- enable-active-high;
+ onewire {
+ compatible = "w1-gpio";
+ gpios = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&chip_w1_pin>;
};
};
#include "axp209.dtsi"
+&ac_power_supply {
+ status = "okay";
+};
+
+&battery_power_supply {
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "disabled";
+};
+
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
};
&mmc0_pins_a {
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ bias-pull-up;
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>;
- vmmc-supply = <&wifi_reg_on>;
+ vmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&mmc0_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
&pio {
chip_vbus_pin: chip_vbus_pin@0 {
- allwinner,pins = "PB10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB10";
+ function = "gpio_out";
};
chip_wifi_reg_on_pin: chip_wifi_reg_on_pin@0 {
- allwinner,pins = "PC19";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PC19";
+ function = "gpio_out";
};
chip_id_det_pin: chip_id_det_pin@0 {
- allwinner,pins = "PG2";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PG2";
+ function = "gpio_in";
+ };
+
+ chip_w1_pin: chip_w1_pin@0 {
+ pins = "PD2";
+ function = "gpio_in";
+ bias-pull-up;
};
};
regulator-always-on;
};
+/*
+ * Both LDO3 and LDO4 are used in parallel to power up the WiFi/BT
+ * Chip.
+ *
+ * If those are not enabled, the SDIO part will not enumerate, and
+ * since there's no way currently to pass DT infos to an SDIO device,
+ * we cannot really do better than this ugly hack for now.
+ */
®_ldo3 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
- regulator-name = "vdd-wifi1";
+ regulator-name = "vcc-wifi-1";
regulator-always-on;
};
®_ldo4 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
- regulator-name = "vdd-wifi2";
+ regulator-name = "vcc-wifi-2";
regulator-always-on;
};
status = "okay";
};
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "disabled";
+};
+
&tcon0 {
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins_a>,
- <&uart3_pins_cts_rts_a>;
+ <&uart3_cts_rts_pins_a>;
status = "okay";
};
#include "sun5i-a13.dtsi"
-/ {
- chosen {
- framebuffer@1 {
- compatible = "allwinner,simple-framebuffer",
- "simple-framebuffer";
- allwinner,pipeline = "de_be0-lcd0-tve0";
- clocks = <&ahb_gates 34>, <&ahb_gates 36>,
- <&ahb_gates 44>, <&de_be_clk>,
- <&tcon_ch1_clk>, <&dram_gates 26>;
- status = "disabled";
- };
- };
-
- soc@01c00000 {
- tve0: tv-encoder@01c0a000 {
- compatible = "allwinner,sun4i-a10-tv-encoder";
- reg = <0x01c0a000 0x1000>;
- clocks = <&ahb_gates 34>;
- resets = <&tcon_ch0_clk 0>;
- status = "disabled";
-
- port {
- #address-cells = <1>;
- #size-cells = <0>;
-
- tve0_in_tcon0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&tcon0_out_tve0>;
- };
- };
- };
- };
-};
-
-&tcon0_out {
- tcon0_out_tve0: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&tve0_in_tcon0>;
- };
-};
*/
#include "sunxi-reference-design-tablet.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pwm/pwm.h>
/ {
};
&i2c1 {
+ /*
+ * The gsl1680 is rated at 400KHz and it will not work reliable at
+ * 100KHz, this has been confirmed on multiple different q8 tablets.
+ * All other devices on this bus are also rated for 400KHz.
+ */
+ clock-frequency = <400000>;
+
+ touchscreen: touchscreen {
+ interrupt-parent = <&pio>;
+ interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>; /* EINT11 (PG11) */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_power_pin>;
+ power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+ /* Tablet dts must provide reg and compatible */
+ status = "disabled";
+ };
+
pcf8563: rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
#include "axp209.dtsi"
+&ac_power_supply {
+ status = "okay";
+};
+
+&battery_power_supply {
+ status = "okay";
+};
+
&lradc {
vref-supply = <®_ldo2>;
};
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <®_vcc3v0>;
bus-width = <4>;
- cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
- cd-inverted;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
status = "okay";
};
&pio {
codec_pa_pin: codec_pa_pin@0 {
- allwinner,pins = "PG10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PG10";
+ function = "gpio_out";
};
mmc0_cd_pin: mmc0_cd_pin@0 {
- allwinner,pins = "PG0";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG0";
+ function = "gpio_in";
+ bias-pull-up;
+ };
+
+ ts_power_pin: ts_power_pin {
+ pins = "PB3";
+ function = "gpio_out";
+ drive-strength = <10>;
+ bias-disable;
};
usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ pins = "PG1";
+ function = "gpio_in";
+ bias-pull-down;
};
usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PG2";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PG2";
+ function = "gpio_in";
+ bias-pull-up;
};
usb0_vbus_pin_a: usb0_vbus_pin@0 {
- allwinner,pins = "PG12";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PG12";
+ function = "gpio_out";
};
};
#include "skeleton.dtsi"
-#include <dt-bindings/clock/sun4i-a10-pll2.h>
+#include <dt-bindings/clock/sun5i-ccu.h>
#include <dt-bindings/dma/sun4i-a10.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sun5i-ccu.h>
/ {
interrupt-parent = <&intc>;
device_type = "cpu";
compatible = "arm,cortex-a8";
reg = <0x0>;
- clocks = <&cpu>;
+ clocks = <&ccu CLK_CPU>;
};
};
- clocks {
+ chosen {
#address-cells = <1>;
#size-cells = <1>;
ranges;
- /*
- * This is a dummy clock, to be used as placeholder on
- * other mux clocks when a specific parent clock is not
- * yet implemented. It should be dropped when the driver
- * is complete.
- */
- dummy: dummy {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <0>;
+ framebuffer@0 {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "de_be0-lcd0";
+ clocks = <&ccu CLK_AHB_LCD>, <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_TCON_CH0>, <&ccu CLK_DRAM_DE_BE>;
+ status = "disabled";
};
- osc24M: clk@01c20050 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-osc-clk";
- reg = <0x01c20050 0x4>;
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
+ framebuffer@1 {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "de_be0-lcd0-tve0";
+ clocks = <&ccu CLK_AHB_TVE>, <&ccu CLK_AHB_LCD>,
+ <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_TCON_CH1>, <&ccu CLK_DRAM_DE_BE>;
+ status = "disabled";
};
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
- osc3M: osc3M_clk {
- compatible = "fixed-factor-clock";
+ osc24M: clk@1c20050 {
#clock-cells = <0>;
- clock-div = <8>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "osc3M";
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
};
osc32k: clk@0 {
clock-frequency = <32768>;
clock-output-names = "osc32k";
};
-
- pll1: clk@01c20000 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll1-clk";
- reg = <0x01c20000 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll1";
- };
-
- pll2: clk@01c20008 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-pll2-clk";
- reg = <0x01c20008 0x8>;
- clocks = <&osc24M>;
- clock-output-names = "pll2-1x", "pll2-2x",
- "pll2-4x", "pll2-8x";
- };
-
- pll3: clk@01c20010 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll3-clk";
- reg = <0x01c20010 0x4>;
- clocks = <&osc3M>;
- clock-output-names = "pll3";
- };
-
- pll3x2: pll3x2_clk {
- compatible = "allwinner,sun4i-a10-pll3-2x-clk", "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <2>;
- clocks = <&pll3>;
- clock-output-names = "pll3-2x";
- };
-
- pll4: clk@01c20018 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll1-clk";
- reg = <0x01c20018 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll4";
- };
-
- pll5: clk@01c20020 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-pll5-clk";
- reg = <0x01c20020 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll5_ddr", "pll5_other";
- };
-
- pll6: clk@01c20028 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-pll6-clk";
- reg = <0x01c20028 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll6_sata", "pll6_other", "pll6";
- };
-
- pll7: clk@01c20030 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll3-clk";
- reg = <0x01c20030 0x4>;
- clocks = <&osc3M>;
- clock-output-names = "pll7";
- };
-
- pll7x2: pll7x2_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <2>;
- clocks = <&pll7>;
- clock-output-names = "pll7-2x";
- };
-
- /* dummy is 200M */
- cpu: cpu@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-cpu-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>;
- clock-output-names = "cpu";
- };
-
- axi: axi@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-axi-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&cpu>;
- clock-output-names = "axi";
- };
-
- ahb: ahb@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun5i-a13-ahb-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&axi>, <&cpu>, <&pll6 1>;
- clock-output-names = "ahb";
- /*
- * Use PLL6 as parent, instead of CPU/AXI
- * which has rate changes due to cpufreq
- */
- assigned-clocks = <&ahb>;
- assigned-clock-parents = <&pll6 1>;
- };
-
- apb0: apb0@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb0-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&ahb>;
- clock-output-names = "apb0";
- };
-
- apb1: clk@01c20058 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb1-clk";
- reg = <0x01c20058 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&osc32k>;
- clock-output-names = "apb1";
- };
-
- axi_gates: clk@01c2005c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-axi-gates-clk";
- reg = <0x01c2005c 0x4>;
- clocks = <&axi>;
- clock-indices = <0>;
- clock-output-names = "axi_dram";
- };
-
- nand_clk: clk@01c20080 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20080 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "nand";
- };
-
- ms_clk: clk@01c20084 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20084 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ms";
- };
-
- mmc0_clk: clk@01c20088 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20088 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc0",
- "mmc0_output",
- "mmc0_sample";
- };
-
- mmc1_clk: clk@01c2008c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c2008c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc1",
- "mmc1_output",
- "mmc1_sample";
- };
-
- mmc2_clk: clk@01c20090 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20090 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc2",
- "mmc2_output",
- "mmc2_sample";
- };
-
- ts_clk: clk@01c20098 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20098 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ts";
- };
-
- ss_clk: clk@01c2009c {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c2009c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ss";
- };
-
- spi0_clk: clk@01c200a0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a0 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi0";
- };
-
- spi1_clk: clk@01c200a4 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a4 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi1";
- };
-
- spi2_clk: clk@01c200a8 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a8 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi2";
- };
-
- ir0_clk: clk@01c200b0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200b0 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ir0";
- };
-
- usb_clk: clk@01c200cc {
- #clock-cells = <1>;
- #reset-cells = <1>;
- compatible = "allwinner,sun5i-a13-usb-clk";
- reg = <0x01c200cc 0x4>;
- clocks = <&pll6 1>;
- clock-output-names = "usb_ohci0", "usb_phy";
- };
-
- codec_clk: clk@01c20140 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-codec-clk";
- reg = <0x01c20140 0x4>;
- clocks = <&pll2 SUN4I_A10_PLL2_1X>;
- clock-output-names = "codec";
- };
-
- mbus_clk: clk@01c2015c {
- #clock-cells = <0>;
- compatible = "allwinner,sun5i-a13-mbus-clk";
- reg = <0x01c2015c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mbus";
- };
};
- soc@01c00000 {
+ soc@1c00000 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
- sram-controller@01c00000 {
+ sram-controller@1c00000 {
compatible = "allwinner,sun4i-a10-sram-controller";
reg = <0x01c00000 0x30>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
- sram_a: sram@00000000 {
+ sram_a: sram@0 {
compatible = "mmio-sram";
reg = <0x00000000 0xc000>;
#address-cells = <1>;
ranges = <0 0x00000000 0xc000>;
};
- sram_d: sram@00010000 {
+ emac_sram: sram-section@8000 {
+ compatible = "allwinner,sun4i-a10-sram-a3-a4";
+ reg = <0x8000 0x4000>;
+ status = "disabled";
+ };
+
+ sram_d: sram@10000 {
compatible = "mmio-sram";
reg = <0x00010000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x00010000 0x1000>;
- otg_sram: sram-section@0000 {
+ otg_sram: sram-section@0 {
compatible = "allwinner,sun4i-a10-sram-d";
reg = <0x0000 0x1000>;
status = "disabled";
};
};
- dma: dma-controller@01c02000 {
+ dma: dma-controller@1c02000 {
compatible = "allwinner,sun4i-a10-dma";
reg = <0x01c02000 0x1000>;
interrupts = <27>;
- clocks = <&ahb_gates 6>;
+ clocks = <&ccu CLK_AHB_DMA>;
#dma-cells = <2>;
};
- spi0: spi@01c05000 {
+ nfc: nand@1c03000 {
+ compatible = "allwinner,sun4i-a10-nand";
+ reg = <0x01c03000 0x1000>;
+ interrupts = <37>;
+ clocks = <&ccu CLK_AHB_NAND>, <&ccu CLK_NAND>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 3>;
+ dma-names = "rxtx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi0: spi@1c05000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c05000 0x1000>;
interrupts = <10>;
- clocks = <&ahb_gates 20>, <&spi0_clk>;
+ clocks = <&ccu CLK_AHB_SPI0>, <&ccu CLK_SPI0>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 27>,
<&dma SUN4I_DMA_DEDICATED 26>;
#size-cells = <0>;
};
- spi1: spi@01c06000 {
+ spi1: spi@1c06000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c06000 0x1000>;
interrupts = <11>;
- clocks = <&ahb_gates 21>, <&spi1_clk>;
+ clocks = <&ccu CLK_AHB_SPI1>, <&ccu CLK_SPI1>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 9>,
<&dma SUN4I_DMA_DEDICATED 8>;
#size-cells = <0>;
};
- mmc0: mmc@01c0f000 {
+ tve0: tv-encoder@1c0a000 {
+ compatible = "allwinner,sun4i-a10-tv-encoder";
+ reg = <0x01c0a000 0x1000>;
+ clocks = <&ccu CLK_AHB_TVE>;
+ resets = <&ccu RST_TVE>;
+ status = "disabled";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tve0_in_tcon0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_out_tve0>;
+ };
+ };
+ };
+
+ emac: ethernet@1c0b000 {
+ compatible = "allwinner,sun4i-a10-emac";
+ reg = <0x01c0b000 0x1000>;
+ interrupts = <55>;
+ clocks = <&ccu CLK_AHB_EMAC>;
+ allwinner,sram = <&emac_sram 1>;
+ status = "disabled";
+ };
+
+ mdio: mdio@1c0b080 {
+ compatible = "allwinner,sun4i-a10-mdio";
+ reg = <0x01c0b080 0x14>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ tcon0: lcd-controller@1c0c000 {
+ compatible = "allwinner,sun5i-a13-tcon";
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <44>;
+ resets = <&ccu RST_LCD>;
+ reset-names = "lcd";
+ clocks = <&ccu CLK_AHB_LCD>,
+ <&ccu CLK_TCON_CH0>,
+ <&ccu CLK_TCON_CH1>;
+ clock-names = "ahb",
+ "tcon-ch0",
+ "tcon-ch1";
+ clock-output-names = "tcon-pixel-clock";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ tcon0_in_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ tcon0_out_tve0: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&tve0_in_tcon0>;
+ allwinner,tcon-channel = <1>;
+ };
+ };
+ };
+ };
+
+ mmc0: mmc@1c0f000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c0f000 0x1000>;
- clocks = <&ahb_gates 8>,
- <&mmc0_clk 0>,
- <&mmc0_clk 1>,
- <&mmc0_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
+ clocks = <&ccu CLK_AHB_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
interrupts = <32>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- mmc1: mmc@01c10000 {
+ mmc1: mmc@1c10000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c10000 0x1000>;
- clocks = <&ahb_gates 9>,
- <&mmc1_clk 0>,
- <&mmc1_clk 1>,
- <&mmc1_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
+ clocks = <&ccu CLK_AHB_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
interrupts = <33>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- mmc2: mmc@01c11000 {
+ mmc2: mmc@1c11000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c11000 0x1000>;
- clocks = <&ahb_gates 10>,
- <&mmc2_clk 0>,
- <&mmc2_clk 1>,
- <&mmc2_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
+ clocks = <&ccu CLK_AHB_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
interrupts = <34>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- usb_otg: usb@01c13000 {
+ usb_otg: usb@1c13000 {
compatible = "allwinner,sun4i-a10-musb";
reg = <0x01c13000 0x0400>;
- clocks = <&ahb_gates 0>;
+ clocks = <&ccu CLK_AHB_OTG>;
interrupts = <38>;
interrupt-names = "mc";
phys = <&usbphy 0>;
status = "disabled";
};
- usbphy: phy@01c13400 {
+ usbphy: phy@1c13400 {
#phy-cells = <1>;
compatible = "allwinner,sun5i-a13-usb-phy";
reg = <0x01c13400 0x10 0x01c14800 0x4>;
reg-names = "phy_ctrl", "pmu1";
- clocks = <&usb_clk 8>;
+ clocks = <&ccu CLK_USB_PHY0>;
clock-names = "usb_phy";
- resets = <&usb_clk 0>, <&usb_clk 1>;
+ resets = <&ccu RST_USB_PHY0>, <&ccu RST_USB_PHY1>;
reset-names = "usb0_reset", "usb1_reset";
status = "disabled";
};
- ehci0: usb@01c14000 {
+ ehci0: usb@1c14000 {
compatible = "allwinner,sun5i-a13-ehci", "generic-ehci";
reg = <0x01c14000 0x100>;
interrupts = <39>;
- clocks = <&ahb_gates 1>;
+ clocks = <&ccu CLK_AHB_EHCI>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
};
- ohci0: usb@01c14400 {
+ ohci0: usb@1c14400 {
compatible = "allwinner,sun5i-a13-ohci", "generic-ohci";
reg = <0x01c14400 0x100>;
interrupts = <40>;
- clocks = <&usb_clk 6>, <&ahb_gates 2>;
+ clocks = <&ccu CLK_USB_OHCI>, <&ccu CLK_AHB_OHCI>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
};
- spi2: spi@01c17000 {
+ crypto: crypto-engine@1c15000 {
+ compatible = "allwinner,sun5i-a13-crypto",
+ "allwinner,sun4i-a10-crypto";
+ reg = <0x01c15000 0x1000>;
+ interrupts = <54>;
+ clocks = <&ccu CLK_AHB_SS>, <&ccu CLK_SS>;
+ clock-names = "ahb", "mod";
+ };
+
+ spi2: spi@1c17000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c17000 0x1000>;
interrupts = <12>;
- clocks = <&ahb_gates 22>, <&spi2_clk>;
+ clocks = <&ccu CLK_AHB_SPI2>, <&ccu CLK_SPI2>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 29>,
<&dma SUN4I_DMA_DEDICATED 28>;
#size-cells = <0>;
};
- intc: interrupt-controller@01c20400 {
+ ccu: clock@1c20000 {
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ intc: interrupt-controller@1c20400 {
compatible = "allwinner,sun4i-a10-ic";
reg = <0x01c20400 0x400>;
interrupt-controller;
#interrupt-cells = <1>;
};
- pio: pinctrl@01c20800 {
+ pio: pinctrl@1c20800 {
reg = <0x01c20800 0x400>;
interrupts = <28>;
- clocks = <&apb0_gates 5>;
+ clocks = <&ccu CLK_APB0_PIO>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
gpio-controller;
interrupt-controller;
#interrupt-cells = <3>;
#gpio-cells = <3>;
+ emac_pins_a: emac0@0 {
+ pins = "PD6", "PD7", "PD10",
+ "PD11", "PD12", "PD13", "PD14",
+ "PD15", "PD18", "PD19", "PD20",
+ "PD21", "PD22", "PD23", "PD24",
+ "PD25", "PD26", "PD27";
+ function = "emac";
+ };
+
i2c0_pins_a: i2c0@0 {
- allwinner,pins = "PB0", "PB1";
- allwinner,function = "i2c0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB0", "PB1";
+ function = "i2c0";
};
i2c1_pins_a: i2c1@0 {
- allwinner,pins = "PB15", "PB16";
- allwinner,function = "i2c1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB15", "PB16";
+ function = "i2c1";
};
i2c2_pins_a: i2c2@0 {
- allwinner,pins = "PB17", "PB18";
- allwinner,function = "i2c2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB17", "PB18";
+ function = "i2c2";
+ };
+
+ ir0_rx_pins_a: ir0@0 {
+ pins = "PB4";
+ function = "ir0";
+ };
+
+ lcd_rgb565_pins: lcd_rgb565@0 {
+ pins = "PD3", "PD4", "PD5", "PD6", "PD7",
+ "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
+ "PD19", "PD20", "PD21", "PD22", "PD23",
+ "PD24", "PD25", "PD26", "PD27";
+ function = "lcd0";
+ };
+
+ lcd_rgb666_pins: lcd_rgb666@0 {
+ pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
+ "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
+ "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
+ "PD24", "PD25", "PD26", "PD27";
+ function = "lcd0";
};
mmc0_pins_a: mmc0@0 {
- allwinner,pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- allwinner,function = "mmc0";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PF0", "PF1", "PF2", "PF3",
+ "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ bias-pull-up;
};
mmc2_pins_a: mmc2@0 {
- allwinner,pins = "PC6", "PC7", "PC8", "PC9",
- "PC10", "PC11", "PC12", "PC13",
- "PC14", "PC15";
- allwinner,function = "mmc2";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PC6", "PC7", "PC8", "PC9",
+ "PC10", "PC11", "PC12", "PC13",
+ "PC14", "PC15";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc2_4bit_pins_a: mmc2-4bit@0 {
+ pins = "PC6", "PC7", "PC8", "PC9",
+ "PC10", "PC11";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ nand_pins_a: nand-base0@0 {
+ pins = "PC0", "PC1", "PC2",
+ "PC5", "PC8", "PC9", "PC10",
+ "PC11", "PC12", "PC13", "PC14",
+ "PC15";
+ function = "nand0";
+ };
+
+ nand_cs0_pins_a: nand-cs@0 {
+ pins = "PC4";
+ function = "nand0";
+ };
+
+ nand_rb0_pins_a: nand-rb@0 {
+ pins = "PC6";
+ function = "nand0";
+ };
+
+ spi2_pins_a: spi2@0 {
+ pins = "PE1", "PE2", "PE3";
+ function = "spi2";
+ };
+
+ spi2_cs0_pins_a: spi2-cs0@0 {
+ pins = "PE0";
+ function = "spi2";
+ };
+
+ uart1_pins_a: uart1@0 {
+ pins = "PE10", "PE11";
+ function = "uart1";
+ };
+
+ uart1_pins_b: uart1@1 {
+ pins = "PG3", "PG4";
+ function = "uart1";
+ };
+
+ uart2_pins_a: uart2@0 {
+ pins = "PD2", "PD3";
+ function = "uart2";
+ };
+
+ uart2_cts_rts_pins_a: uart2-cts-rts@0 {
+ pins = "PD4", "PD5";
+ function = "uart2";
};
uart3_pins_a: uart3@0 {
- allwinner,pins = "PG9", "PG10";
- allwinner,function = "uart3";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PG9", "PG10";
+ function = "uart3";
};
- uart3_pins_cts_rts_a: uart3-cts-rts@0 {
- allwinner,pins = "PG11", "PG12";
- allwinner,function = "uart3";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart3_cts_rts_pins_a: uart3-cts-rts@0 {
+ pins = "PG11", "PG12";
+ function = "uart3";
};
pwm0_pins: pwm0 {
- allwinner,pins = "PB2";
- allwinner,function = "pwm";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PB2";
+ function = "pwm";
};
};
- timer@01c20c00 {
+ timer@1c20c00 {
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0x90>;
interrupts = <22>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_HOSC>;
};
- wdt: watchdog@01c20c90 {
+ wdt: watchdog@1c20c90 {
compatible = "allwinner,sun4i-a10-wdt";
reg = <0x01c20c90 0x10>;
};
- lradc: lradc@01c22800 {
+ ir0: ir@1c21800 {
+ compatible = "allwinner,sun4i-a10-ir";
+ clocks = <&ccu CLK_APB0_IR>, <&ccu CLK_IR>;
+ clock-names = "apb", "ir";
+ interrupts = <5>;
+ reg = <0x01c21800 0x40>;
+ status = "disabled";
+ };
+
+ lradc: lradc@1c22800 {
compatible = "allwinner,sun4i-a10-lradc-keys";
reg = <0x01c22800 0x100>;
interrupts = <31>;
status = "disabled";
};
- codec: codec@01c22c00 {
+ codec: codec@1c22c00 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun4i-a10-codec";
reg = <0x01c22c00 0x40>;
interrupts = <30>;
- clocks = <&apb0_gates 0>, <&codec_clk>;
+ clocks = <&ccu CLK_APB0_CODEC>, <&ccu CLK_CODEC>;
clock-names = "apb", "codec";
dmas = <&dma SUN4I_DMA_NORMAL 19>,
<&dma SUN4I_DMA_NORMAL 19>;
status = "disabled";
};
- sid: eeprom@01c23800 {
+ sid: eeprom@1c23800 {
compatible = "allwinner,sun4i-a10-sid";
reg = <0x01c23800 0x10>;
};
- rtp: rtp@01c25000 {
+ rtp: rtp@1c25000 {
compatible = "allwinner,sun5i-a13-ts";
reg = <0x01c25000 0x100>;
interrupts = <29>;
#thermal-sensor-cells = <0>;
};
- uart1: serial@01c28400 {
+ uart0: serial@1c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <1>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_APB1_UART0>;
+ status = "disabled";
+ };
+
+ uart1: serial@1c28400 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28400 0x400>;
interrupts = <2>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 17>;
+ clocks = <&ccu CLK_APB1_UART1>;
status = "disabled";
};
- uart3: serial@01c28c00 {
+ uart2: serial@1c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <3>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_APB1_UART2>;
+ status = "disabled";
+ };
+
+ uart3: serial@1c28c00 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28c00 0x400>;
interrupts = <4>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 19>;
+ clocks = <&ccu CLK_APB1_UART3>;
status = "disabled";
};
- i2c0: i2c@01c2ac00 {
+ i2c0: i2c@1c2ac00 {
compatible = "allwinner,sun4i-a10-i2c";
reg = <0x01c2ac00 0x400>;
interrupts = <7>;
- clocks = <&apb1_gates 0>;
+ clocks = <&ccu CLK_APB1_I2C0>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- i2c1: i2c@01c2b000 {
+ i2c1: i2c@1c2b000 {
compatible = "allwinner,sun4i-a10-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <8>;
- clocks = <&apb1_gates 1>;
+ clocks = <&ccu CLK_APB1_I2C1>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- i2c2: i2c@01c2b400 {
+ i2c2: i2c@1c2b400 {
compatible = "allwinner,sun4i-a10-i2c";
reg = <0x01c2b400 0x400>;
interrupts = <9>;
- clocks = <&apb1_gates 2>;
+ clocks = <&ccu CLK_APB1_I2C2>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- timer@01c60000 {
+ timer@1c60000 {
compatible = "allwinner,sun5i-a13-hstimer";
reg = <0x01c60000 0x1000>;
interrupts = <82>, <83>;
- clocks = <&ahb_gates 28>;
+ clocks = <&ccu CLK_AHB_HSTIMER>;
+ };
+
+ fe0: display-frontend@1e00000 {
+ compatible = "allwinner,sun5i-a13-display-frontend";
+ reg = <0x01e00000 0x20000>;
+ interrupts = <47>;
+ clocks = <&ccu CLK_DE_FE>, <&ccu CLK_DE_FE>,
+ <&ccu CLK_DRAM_DE_FE>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&ccu RST_DE_FE>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fe0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ fe0_out_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_in_fe0>;
+ };
+ };
+ };
+ };
+
+ be0: display-backend@1e60000 {
+ compatible = "allwinner,sun5i-a13-display-backend";
+ reg = <0x01e60000 0x10000>;
+ interrupts = <47>;
+ clocks = <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_DRAM_DE_BE>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&ccu RST_DE_BE>;
+ status = "disabled";
+
+ assigned-clocks = <&ccu CLK_DE_BE>;
+ assigned-clock-rates = <300000000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ be0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ be0_in_fe0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&fe0_out_be0>;
+ };
+ };
+
+ be0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ be0_out_tcon0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_in_be0>;
+ };
+ };
+ };
};
};
};
--- /dev/null
+/*
+ * Copyright 2016 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN5I_H_
+#define _DT_BINDINGS_CLK_SUN5I_H_
+
+#define CLK_HOSC 1
+
+#define CLK_PLL_VIDEO0_2X 9
+
+#define CLK_PLL_VIDEO1_2X 16
+#define CLK_CPU 17
+
+#define CLK_AHB_OTG 23
+#define CLK_AHB_EHCI 24
+#define CLK_AHB_OHCI 25
+#define CLK_AHB_SS 26
+#define CLK_AHB_DMA 27
+#define CLK_AHB_BIST 28
+#define CLK_AHB_MMC0 29
+#define CLK_AHB_MMC1 30
+#define CLK_AHB_MMC2 31
+#define CLK_AHB_NAND 32
+#define CLK_AHB_SDRAM 33
+#define CLK_AHB_EMAC 34
+#define CLK_AHB_TS 35
+#define CLK_AHB_SPI0 36
+#define CLK_AHB_SPI1 37
+#define CLK_AHB_SPI2 38
+#define CLK_AHB_GPS 39
+#define CLK_AHB_HSTIMER 40
+#define CLK_AHB_VE 41
+#define CLK_AHB_TVE 42
+#define CLK_AHB_LCD 43
+#define CLK_AHB_CSI 44
+#define CLK_AHB_HDMI 45
+#define CLK_AHB_DE_BE 46
+#define CLK_AHB_DE_FE 47
+#define CLK_AHB_IEP 48
+#define CLK_AHB_GPU 49
+#define CLK_APB0_CODEC 50
+#define CLK_APB0_SPDIF 51
+#define CLK_APB0_I2S 52
+#define CLK_APB0_PIO 53
+#define CLK_APB0_IR 54
+#define CLK_APB0_KEYPAD 55
+#define CLK_APB1_I2C0 56
+#define CLK_APB1_I2C1 57
+#define CLK_APB1_I2C2 58
+#define CLK_APB1_UART0 59
+#define CLK_APB1_UART1 60
+#define CLK_APB1_UART2 61
+#define CLK_APB1_UART3 62
+#define CLK_NAND 63
+#define CLK_MMC0 64
+#define CLK_MMC1 65
+#define CLK_MMC2 66
+#define CLK_TS 67
+#define CLK_SS 68
+#define CLK_SPI0 69
+#define CLK_SPI1 70
+#define CLK_SPI2 71
+#define CLK_IR 72
+#define CLK_I2S 73
+#define CLK_SPDIF 74
+#define CLK_KEYPAD 75
+#define CLK_USB_OHCI 76
+#define CLK_USB_PHY0 77
+#define CLK_USB_PHY1 78
+#define CLK_GPS 79
+#define CLK_DRAM_VE 80
+#define CLK_DRAM_CSI 81
+#define CLK_DRAM_TS 82
+#define CLK_DRAM_TVE 83
+#define CLK_DRAM_DE_FE 84
+#define CLK_DRAM_DE_BE 85
+#define CLK_DRAM_ACE 86
+#define CLK_DRAM_IEP 87
+#define CLK_DE_BE 88
+#define CLK_DE_FE 89
+#define CLK_TCON_CH0 90
+
+#define CLK_TCON_CH1 92
+#define CLK_CSI 93
+#define CLK_VE 94
+#define CLK_CODEC 95
+#define CLK_AVS 96
+#define CLK_HDMI 97
+#define CLK_GPU 98
+
+#define CLK_IEP 100
+
+#endif /* _DT_BINDINGS_CLK_SUN5I_H_ */
--- /dev/null
+/*
+ * Copyright 2016 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _RST_SUN5I_H_
+#define _RST_SUN5I_H_
+
+#define RST_USB_PHY0 0
+#define RST_USB_PHY1 1
+#define RST_GPS 2
+#define RST_DE_BE 3
+#define RST_DE_FE 4
+#define RST_TVE 5
+#define RST_LCD 6
+#define RST_CSI 7
+#define RST_VE 8
+#define RST_GPU 9
+#define RST_IEP 10
+
+#endif /* _RST_SUN5I_H_ */
projects / oweals / u-boot.git / commitdiff