* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
+#include <dm.h>
+#include <ns16550.h>
#include <netdev.h>
#include <asm/io.h>
#include <asm/arch/mem.h>
#include <i2c.h>
#include <twl4030.h>
#include <asm/mach-types.h>
+#include <asm/omap_musb.h>
#include <linux/mtd/nand.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+#include <linux/usb/musb.h>
#include "evm.h"
-#define OMAP3EVM_GPIO_ETH_RST_GEN1 64
-#define OMAP3EVM_GPIO_ETH_RST_GEN2 7
+#ifdef CONFIG_USB_EHCI_HCD
+#include <usb.h>
+#include <asm/ehci-omap.h>
+#endif
+
+#define OMAP3EVM_GPIO_ETH_RST_GEN1 64
+#define OMAP3EVM_GPIO_ETH_RST_GEN2 7
DECLARE_GLOBAL_DATA_PTR;
+static const struct ns16550_platdata omap3_evm_serial = {
+ .base = OMAP34XX_UART1,
+ .reg_shift = 2,
+ .clock = V_NS16550_CLK,
+ .fcr = UART_FCR_DEFVAL,
+};
+
+U_BOOT_DEVICE(omap3_evm_uart) = {
+ "ns16550_serial",
+ &omap3_evm_serial
+};
+
static u32 omap3_evm_version;
u32 get_omap3_evm_rev(void)
default:
omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
}
-#else
+#else /* !CONFIG_CMD_NET */
#if defined(CONFIG_STATIC_BOARD_REV)
- /*
- * Look for static defintion of the board revision
- */
+ /* Look for static defintion of the board revision */
omap3_evm_version = CONFIG_STATIC_BOARD_REV;
#else
- /*
- * Fallback to the default above.
- */
+ /* Fallback to the default above */
omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
-#endif
-#endif /* CONFIG_CMD_NET */
+#endif /* CONFIG_STATIC_BOARD_REV */
+#endif /* CONFIG_CMD_NET */
}
-#ifdef CONFIG_USB_OMAP3
-/*
- * MUSB port on OMAP3EVM Rev >= E requires extvbus programming.
- */
+#if defined(CONFIG_USB_MUSB_GADGET) || defined(CONFIG_USB_MUSB_HOST)
+/* MUSB port on OMAP3EVM Rev >= E requires extvbus programming. */
u8 omap3_evm_need_extvbus(void)
{
u8 retval = 0;
return retval;
}
-#endif
+#endif /* CONFIG_USB_MUSB_{GADGET,HOST} */
/*
* Routine: board_init
return 0;
}
-#ifdef CONFIG_SPL_BUILD
+#if defined(CONFIG_SPL_BUILD)
/*
* Routine: get_board_mem_timings
* Description: If we use SPL then there is no x-loader nor config header
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
timings->mr = MICRON_V_MR_165;
}
-#endif
+#endif /* CONFIG_SPL_BUILD */
+
+#if defined(CONFIG_USB_MUSB_OMAP2PLUS)
+static struct musb_hdrc_config musb_config = {
+ .multipoint = 1,
+ .dyn_fifo = 1,
+ .num_eps = 16,
+ .ram_bits = 12,
+};
+
+static struct omap_musb_board_data musb_board_data = {
+ .interface_type = MUSB_INTERFACE_ULPI,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_USB_MUSB_HOST)
+ .mode = MUSB_HOST,
+#elif defined(CONFIG_USB_MUSB_GADGET)
+ .mode = MUSB_PERIPHERAL,
+#else
+#error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET"
+#endif /* CONFIG_USB_MUSB_{GADGET,HOST} */
+ .config = &musb_config,
+ .power = 100,
+ .platform_ops = &omap2430_ops,
+ .board_data = &musb_board_data,
+};
+#endif /* CONFIG_USB_MUSB_OMAP2PLUS */
/*
* Routine: misc_init_r
*/
int misc_init_r(void)
{
+ twl4030_power_init();
#ifdef CONFIG_SYS_I2C_OMAP24XX
i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
#endif
omap_die_id_display();
+#if defined(CONFIG_USB_MUSB_OMAP2PLUS)
+ musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE);
+#endif
+
+#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)
+ omap_die_id_usbethaddr();
+#endif
return 0;
}
MUX_EVM();
}
-#ifdef CONFIG_CMD_NET
+#if defined(CONFIG_CMD_NET)
/*
* Routine: setup_net_chip
* Description: Setting up the configuration GPMC registers specific to the
int board_eth_init(bd_t *bis)
{
int rc = 0;
-#ifdef CONFIG_SMC911X
+#if defined(CONFIG_SMC911X)
#define STR_ENV_ETHADDR "ethaddr"
struct eth_device *dev;
rc = -1;
}
}
-#endif
+#endif /* CONFIG_SMC911X */
return rc;
}
#endif /* CONFIG_CMD_NET */
{
return omap_mmc_init(0, 0, 0, -1, -1);
}
-#endif
-#if defined(CONFIG_MMC)
void board_mmc_power_init(void)
{
twl4030_power_mmc_init(0);
}
-#endif
+#endif /* CONFIG_MMC */
+
+#if defined(CONFIG_USB_EHCI_HCD)
+static struct omap_usbhs_board_data usbhs_bdata = {
+ .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED
+};
+
+int ehci_hcd_init(int index, enum usb_init_type init,
+ struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+ return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
+}
+
+int ehci_hcd_stop(int index)
+{
+ return omap_ehci_hcd_stop();
+}
+#endif /* CONFIG_USB_EHCI_HCD */
+
+#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) && !defined(CONFIG_CMD_NET)
+int board_eth_init(bd_t *bis)
+{
+ return usb_eth_initialize(bis);
+}
+#endif /* CONFIG_USB_ETHER */
* SPDX-License-Identifier: GPL-2.0+
*/
-#ifndef __OMAP3EVM_CONFIG_H
-#define __OMAP3EVM_CONFIG_H
+#ifndef __CONFIG_H
+#define __CONFIG_H
-#include <asm/arch/cpu.h>
-#include <asm/arch/omap.h>
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-/* ----------------------------------------------------------------------------
- * Supported U-Boot features
- * ----------------------------------------------------------------------------
- */
-#define CONFIG_SYS_LONGHELP
-
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Add auto-completion support */
-#define CONFIG_AUTO_COMPLETE
-
-/* ----------------------------------------------------------------------------
- * Supported hardware
- * ----------------------------------------------------------------------------
- */
-
-/* SPL */
-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
-#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-
-/* Partition tables */
-
-/* USB
- *
- * Enable CONFIG_USB_MUSB_HCD for Host functionalities MSC, keyboard
- * Enable CONFIG_USB_MUSB_UDD for Device functionalities.
- */
-#define CONFIG_USB_OMAP3
-#define CONFIG_USB_MUSB_HCD
-/* #define CONFIG_USB_MUSB_UDC */
-
-/* NAND SPL */
-#define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SPL_NAND_ECC
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT 64
-#define CONFIG_SYS_NAND_PAGE_SIZE 2048
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
-#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
- 10, 11, 12, 13}
-#define CONFIG_SYS_NAND_ECCSIZE 512
-#define CONFIG_SYS_NAND_ECCBYTES 3
-#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
-
-/*
- * High level configuration options
- */
-
-#define CONFIG_SDRC /* The chip has SDRC controller */
-
-/*
- * Clock related definitions
- */
-#define V_OSCK 26000000 /* Clock output from T2 */
-#define V_SCLK (V_OSCK >> 1)
-
-/*
- * OMAP3 has 12 GP timers, they can be driven by the system clock
- * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
- * This rate is divided by a local divisor.
- */
-#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
-#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-
-/* Size of environment - 128KB */
-#define CONFIG_ENV_SIZE (128 << 10)
-
-/* Size of malloc pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
-
-/*
- * Physical Memory Map
- * Note 1: CS1 may or may not be populated
- * Note 2: SDRAM size is expected to be at least 32MB
- */
-#define CONFIG_NR_DRAM_BANKS 2
-#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
-
-/* Limits for memtest */
-#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
-#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
- 0x01F00000) /* 31MB */
-
-/* Default load address */
-#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0)
-
-/* -----------------------------------------------------------------------------
- * Hardware drivers
- * -----------------------------------------------------------------------------
- */
-
-/*
- * NS16550 Configuration
- */
-#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
-
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
-
-/*
- * select serial console configuration
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SERIAL1 1 /* UART1 on OMAP3 EVM */
-#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
-#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
- 115200}
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
-#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
+#include <configs/ti_omap3_common.h>
/*
- * PISMO support
+ * We are only ever GP parts and will utilize all of the "downloaded image"
+ * area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB).
*/
-/* Monitor at start of flash - Reserve 2 sectors */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10)
-
-/* Start location & size of environment */
-#define ONENAND_ENV_OFFSET 0x260000
-#define SMNAND_ENV_OFFSET 0x260000
+#undef CONFIG_SPL_TEXT_BASE
+#define CONFIG_SPL_TEXT_BASE 0x40200000
-#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-
-/*
- * NAND
- */
-/* Physical address to access NAND */
-#define CONFIG_SYS_NAND_ADDR NAND_BASE
-
-/* Physical address to access NAND at CS0 */
-#define CONFIG_SYS_NAND_BASE NAND_BASE
-
-/* Max number of NAND devices */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
-/* Timeout values (in ticks) */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
- CONFIG_SYS_MAX_NAND_DEVICE)
-
-#define CONFIG_SYS_JFFS2_MEM_NAND
-#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-
-#define CONFIG_JFFS2_NAND
-/* nand device jffs2 lives on */
-#define CONFIG_JFFS2_DEV "nand0"
-/* Start of jffs2 partition */
-#define CONFIG_JFFS2_PART_OFFSET 0x680000
-/* Size of jffs2 partition */
-#define CONFIG_JFFS2_PART_SIZE 0xf980000
-
-/*
- * USB
- */
-#ifdef CONFIG_USB_OMAP3
-
-#ifdef CONFIG_USB_MUSB_HCD
-
-#ifdef CONFIG_USB_KEYBOARD
-#define CONFIG_SYS_USB_EVENT_POLL
-#define CONFIG_PREBOOT "usb start"
-#endif /* CONFIG_USB_KEYBOARD */
-
-#endif /* CONFIG_USB_MUSB_HCD */
-
-#ifdef CONFIG_USB_MUSB_UDC
-/* USB device configuration */
-#define CONFIG_USB_DEVICE
-#define CONFIG_USB_TTY
-
-/* Change these to suit your needs */
-#define CONFIG_USBD_VENDORID 0x0451
-#define CONFIG_USBD_PRODUCTID 0x5678
-#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
-#define CONFIG_USBD_PRODUCT_NAME "EVM"
-#endif /* CONFIG_USB_MUSB_UDC */
-
-#endif /* CONFIG_USB_OMAP3 */
-
-/* ----------------------------------------------------------------------------
- * U-Boot features
- * ----------------------------------------------------------------------------
- */
-#define CONFIG_SYS_MAXARGS 16 /* max args for a command */
+#define CONFIG_SPL_FRAMEWORK
#define CONFIG_MISC_INIT_R
-
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
-/* Size of Console IO buffer */
-#define CONFIG_SYS_CBSIZE 512
-
-/* Size of print buffer */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-
-/* Size of bootarg buffer */
-#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
-#define CONFIG_BOOTFILE "uImage"
+/* Override OMAP3 serial console configuration */
+#undef CONFIG_CONS_INDEX
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
+#if defined(CONFIG_SPL_BUILD)
+#undef CONFIG_SYS_NS16550_REG_SIZE
+#else /* !CONFIG_SPL_BUILD */
+#define CONFIG_SYS_NS16550_REG_SIZE (-1)
+#endif /* CONFIG_SPL_BUILD */
-/*
- * NAND / OneNAND
- */
-#if defined(CONFIG_CMD_NAND)
+/* NAND */
+#if defined(CONFIG_NAND)
+#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_SYS_FLASH_BASE NAND_BASE
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_BCH
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
+ 10, 11, 12, 13}
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
+#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
+#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
+#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
+#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SPL_OMAP3_ID_NAND
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
+#endif /* CONFIG_NAND */
-#define CONFIG_NAND_OMAP_GPMC
-#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
-#elif defined(CONFIG_CMD_ONENAND)
-#define CONFIG_SYS_FLASH_BASE ONENAND_MAP
-#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
-#endif
+#define CONFIG_USB_OMAP3
-#if !defined(CONFIG_ENV_IS_NOWHERE)
-#if defined(CONFIG_CMD_NAND)
-#elif defined(CONFIG_CMD_ONENAND)
-#define CONFIG_ENV_OFFSET ONENAND_ENV_OFFSET
-#endif
-#endif /* CONFIG_ENV_IS_NOWHERE */
+/* MUSB */
+#define CONFIG_USB_MUSB_OMAP2PLUS
+#define CONFIG_USB_MUSB_PIO_ONLY
+#define CONFIG_USB_ETHER
+#define CONFIG_USB_ETHER_RNDIS
-#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET
+/* USB EHCI */
+#define CONFIG_SYS_USB_FAT_BOOT_PARTITION 1
+/* SMSC911x Ethernet */
#if defined(CONFIG_CMD_NET)
-
-/* Ethernet (SMSC9115 from SMSC9118 family) */
#define CONFIG_SMC911X
#define CONFIG_SMC911X_32_BIT
-#define CONFIG_SMC911X_BASE 0x2C000000
-
-/* BOOTP fields */
-#define CONFIG_BOOTP_SUBNETMASK 0x00000001
-#define CONFIG_BOOTP_GATEWAY 0x00000002
-#define CONFIG_BOOTP_HOSTNAME 0x00000004
-#define CONFIG_BOOTP_BOOTPATH 0x00000010
-
+#define CONFIG_SMC911X_BASE 0x2C000000
#endif /* CONFIG_CMD_NET */
-/* Support for relocation */
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
-#define CONFIG_SYS_INIT_RAM_SIZE 0x800
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/* -----------------------------------------------------------------------------
- * Board specific
- * -----------------------------------------------------------------------------
- */
-
-/* Uncomment to define the board revision statically */
-/* #define CONFIG_STATIC_BOARD_REV OMAP3EVM_BOARD_GEN_2 */
-
-/* Defines for SPL */
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_TEXT_BASE 0x40200800
-#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \
- CONFIG_SPL_TEXT_BASE)
-
-#define CONFIG_SPL_BSS_START_ADDR 0x80000000
-#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
-
-#define CONFIG_SPL_OMAP3_ID_NAND
-#define CONFIG_SPL_LDSCRIPT "arch/arm/mach-omap2/u-boot-spl.lds"
-
-/*
- * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
- * 64 bytes before this address should be set aside for u-boot.img's
- * header. That is 0x800FFFC0--0x80100000 should not be used for any
- * other needs.
- */
-#define CONFIG_SYS_TEXT_BASE 0x80100000
-#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
-
-/* -----------------------------------------------------------------------------
- * Default environment
- * -----------------------------------------------------------------------------
- */
+/* Environment */
+#define CONFIG_PREBOOT "usb start"
#define CONFIG_EXTRA_ENV_SETTINGS \
+ DEFAULT_LINUX_BOOT_ENV \
+ "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
+ "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
"loadaddr=0x82000000\0" \
"usbtty=cdc_acm\0" \
"mmcdev=0\0" \
"console=ttyO0,115200n8\0" \
"mmcargs=setenv bootargs console=${console} " \
+ "${optargs} " \
"root=/dev/mmcblk0p2 rw " \
- "rootfstype=ext3 rootwait\0" \
+ "rootfstype=ext4 rootwait\0" \
"nandargs=setenv bootargs console=${console} " \
- "root=/dev/mtdblock4 rw " \
- "rootfstype=jffs2\0" \
+ "${optargs} " \
+ "root=ubi0:rootfs rw ubi.mtd=rootfs noinitrd " \
+ "rootfstype=ubifs rootwait\0" \
"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source ${loadaddr}\0" \
- "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
- "mmcboot=echo Booting from mmc ...; " \
+ "loaduimage=setenv bootfile uImage; " \
+ "fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
+ "loadzimage=setenv bootfile zImage; " \
+ "fatload mmc ${mmcdev} ${loadaddr} zImage\0" \
+ "loaddtb=fatload mmc ${mmcdev} ${fdtaddr} omap3-evm.dtb\0" \
+ "mmcboot=echo Booting ${bootfile} from mmc ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr} - ${fdtaddr}\0" \
+ "mmcbootz=echo Booting ${bootfile} from mmc ...; " \
"run mmcargs; " \
- "bootm ${loadaddr}\0" \
- "nandboot=echo Booting from nand ...; " \
+ "bootz ${loadaddr} - ${fdtaddr}\0" \
+ "nandboot=echo Booting uImage from nand ...; " \
"run nandargs; " \
- "onenand read ${loadaddr} 280000 400000; " \
- "bootm ${loadaddr}\0" \
+ "nand read ${loadaddr} kernel; " \
+ "nand read ${fdtaddr} dtb; " \
+ "bootm ${loadaddr} - ${fdtaddr}\0"
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
- "if run loaduimage; then " \
- "run mmcboot; " \
- "else run nandboot; " \
- "fi; " \
+ "if run loadzimage && run loaddtb; then " \
+ "run mmcbootz; fi; " \
+ "if run loaduimage && run loaddtb; then " \
+ "run mmcboot; fi; " \
+ "run nandboot; " \
"fi; " \
"else run nandboot; fi"
-#endif /* __OMAP3EVM_CONFIG_H */
+#endif /* __CONFIG_H */
projects / oweals / u-boot.git / commitdiff