select BOARD_EARLY_INIT_F
select BOARD_LATE_INIT
select DM
+ select SPL_DM if SPL
select DM_THERMAL
+ select DM_MMC
+ select DM_ETH
+ select DM_REGULATOR
+ select SPL_DM_REGULATOR if SPL
+ select DM_SERIAL
+ select DM_I2C
+ select DM_GPIO
+ select DM_USB
select MX6QDL
select SUPPORT_SPL
+ select SPL_SEPARATE_BSS if SPL
imply CMD_DM
imply CMD_SPL
#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
-#include <asm/gpio.h>
-#include <asm/io.h>
#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/mxc_i2c.h>
#include <env.h>
#include <errno.h>
-#include <fsl_esdhc_imx.h>
-#include <fuse.h>
-#include <i2c.h>
#include <miiphy.h>
-#include <mmc.h>
-#include <net.h>
-#include <netdev.h>
#include <usb.h>
#include <usb/ehci-ci.h>
#include <led.h>
DECLARE_GLOBAL_DATA_PTR;
-#define ENET_PAD_CTRL \
- (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_HYS)
-
-#define I2C_PAD_CTRL \
- (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_HYS | PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-
-static struct i2c_pads_info kp_imx6q_tpc_i2c_pad_info0 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_CSI0_DAT9__I2C1_SCL | PC,
- .gpio_mode = MX6Q_PAD_CSI0_DAT9__GPIO5_IO27 | PC,
- .gp = IMX_GPIO_NR(5, 27)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_CSI0_DAT8__I2C1_SDA | PC,
- .gpio_mode = MX6Q_PAD_CSI0_DAT8__GPIO5_IO26 | PC,
- .gp = IMX_GPIO_NR(5, 26)
- }
-};
-
-static struct i2c_pads_info kp_imx6q_tpc_i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL | PC,
- .gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12 | PC,
- .gp = IMX_GPIO_NR(4, 12)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | PC,
- .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | PC,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
}
#ifdef CONFIG_FEC_MXC
-static iomux_v3_cfg_t const enet_pads[] = {
- IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL |
- MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL |
- MUX_PAD_CTRL(ENET_PAD_CTRL)),
- /* AR8031 PHY Reset */
- IOMUX_PADS(PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-static void eth_phy_reset(void)
-{
- /* Reset AR8031 PHY */
- gpio_direction_output(IMX_GPIO_NR(1, 25), 0);
- mdelay(10);
- gpio_set_value(IMX_GPIO_NR(1, 25), 1);
- udelay(100);
-}
-
static int setup_fec_clock(void)
{
struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
return enable_fec_anatop_clock(0, ENET_50MHZ);
}
-int board_eth_init(bd_t *bis)
-{
- SETUP_IOMUX_PADS(enet_pads);
- setup_fec_clock();
- eth_phy_reset();
-
- return cpu_eth_init(bis);
-}
-
static int ar8031_phy_fixup(struct phy_device *phydev)
{
unsigned short val;
}
#endif
-#ifdef CONFIG_FSL_ESDHC_IMX
-
-#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4)
-static struct fsl_esdhc_cfg usdhc_cfg[] = {
- { USDHC2_BASE_ADDR },
- { USDHC4_BASE_ADDR },
-};
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-
- switch (cfg->esdhc_base) {
- case USDHC2_BASE_ADDR:
- return !gpio_get_value(USDHC2_CD_GPIO);
- case USDHC4_BASE_ADDR:
- return 1; /* eMMC/uSDHC4 is always present */
- }
-
- return 0;
-}
-
-int board_mmc_init(bd_t *bis)
-{
- int i, ret;
-
- /*
- * According to the board_mmc_init() the following map is done:
- * (U-Boot device node) (Physical Port)
- * mmc0 micro SD
- * mmc2 eMMC
- */
- gpio_direction_input(USDHC2_CD_GPIO);
-
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
-
- for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
- if (ret)
- return ret;
- }
-
- return 0;
-}
-#endif
-
#ifdef CONFIG_USB_EHCI_MX6
static void setup_usb(void)
{
*/
imx_iomux_set_gpr_register(1, 13, 1, 0);
}
-
-int board_usb_phy_mode(int port)
-{
- if (port == 1)
- return USB_INIT_HOST;
- else
- return USB_INIT_DEVICE;
-}
-
-int board_ehci_power(int port, int on)
-{
- switch (port) {
- case 0:
- break;
- case 1:
- gpio_direction_output(IMX_GPIO_NR(3, 31), !!on);
- break;
- default:
- printf("MXC USB port %d not yet supported\n", port);
- return -EINVAL;
- }
-
- return 0;
-}
#endif
int board_early_init_f(void)
setup_usb();
#endif
+#ifdef CONFIG_FEC_MXC
+ setup_fec_clock();
+#endif
+
return 0;
}
/* Enable eim_slow clocks */
setbits_le32(&mxc_ccm->CCGR6, 0x1 << MXC_CCM_CCGR6_EMI_SLOW_OFFSET);
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &kp_imx6q_tpc_i2c_pad_info0);
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &kp_imx6q_tpc_i2c_pad_info1);
-
return 0;
}
#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux.h>
#include <asm/arch/mx6-ddr.h>
-#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/mxc_i2c.h>
#include <asm/io.h>
#include <errno.h>
-#include <fuse.h>
-#include <fsl_esdhc_imx.h>
-#include <i2c.h>
-#include <mmc.h>
#include <spl.h>
-#define UART_PAD_CTRL \
- (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL \
- (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
DECLARE_GLOBAL_DATA_PTR;
static void ccgr_init(void)
writel(0x000003FF, &ccm->CCGR6);
}
-/* onboard microSD */
-static iomux_v3_cfg_t const usdhc2_pads[] = {
- IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_CS3__GPIO6_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-/* eMMC */
-static iomux_v3_cfg_t const usdhc4_pads[] = {
- IOMUX_PADS(PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-};
-
-/* SD */
-static void setup_iomux_sd(void)
-{
- SETUP_IOMUX_PADS(usdhc2_pads);
- SETUP_IOMUX_PADS(usdhc4_pads);
-}
-
-/* UART */
-static iomux_v3_cfg_t const uart1_pads[] = {
- IOMUX_PADS(PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
-};
-
-static void setup_iomux_uart(void)
-{
- SETUP_IOMUX_PADS(uart1_pads);
-}
-
-/* USB */
-static iomux_v3_cfg_t const usb_pads[] = {
- IOMUX_PADS(PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-static void setup_iomux_usb(void)
-{
- SETUP_IOMUX_PADS(usb_pads);
-}
-
/* DDR3 */
static const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
.dram_sdclk_0 = 0x00000030,
#endif
}
-struct fsl_esdhc_cfg usdhc_cfg[] = {
- {USDHC2_BASE_ADDR},
- {USDHC4_BASE_ADDR},
-};
-
-#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4)
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret = 0;
-
- switch (cfg->esdhc_base) {
- case USDHC2_BASE_ADDR:
- ret = !gpio_get_value(USDHC2_CD_GPIO);
- break;
- case USDHC4_BASE_ADDR:
- ret = 1; /* eMMC/uSDHC4 is always present */
- break;
- }
-
- return ret;
-}
-
-int board_mmc_init(bd_t *bd)
-{
- struct src *psrc = (struct src *)SRC_BASE_ADDR;
- unsigned int reg = readl(&psrc->sbmr1) >> 11;
- /*
- * Upon reading BOOT_CFG register the following map is done:
- * Bit 11 and 12 of BOOT_CFG register can determine the current
- * mmc port
- * 0x1 SD1
- * 0x3 SD4
- */
-
- switch (reg & 0x3) {
- case 0x1:
- SETUP_IOMUX_PADS(usdhc2_pads);
- usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
- break;
- case 0x3:
- SETUP_IOMUX_PADS(usdhc4_pads);
- usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
- gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
- break;
- }
-
- return fsl_esdhc_initialize(bd, &usdhc_cfg[0]);
-}
-
void board_boot_order(u32 *spl_boot_list)
{
u32 boot_device = spl_boot_device();
/* setup GP timer */
timer_init();
- setup_iomux_sd();
- setup_iomux_uart();
- setup_iomux_usb();
+ /* Early - pre reloc - driver model setup */
+ spl_early_init();
/* UART clocks enabled and gd valid - init serial console */
preloader_console_init();
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
-
- /* load/boot image from boot device */
- board_init_r(NULL, 0);
}
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2200
CONFIG_MX6_DDRCAL=y
CONFIG_TARGET_KP_IMX6Q_TPC=y
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_FIT=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
# CONFIG_USE_BOOTCOMMAND is not set
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_SPL_RAW_IMAGE_SUPPORT=y
+CONFIG_SPL_PAYLOAD="u-boot.img"
+CONFIG_SPL_POWER_SUPPORT=y
CONFIG_SPL_WATCHDOG_SUPPORT=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_STOP_STR="."
CONFIG_CMD_EXT4_WRITE=y
# CONFIG_ISO_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6q-kp"
+CONFIG_OF_SPL_REMOVE_PROPS="interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents interrupts dmas dma-names"
CONFIG_ENV_IS_IN_MMC=y
+# CONFIG_BLOCK_CACHE is not set
+CONFIG_SPL_CLK_IMX6Q=y
+CONFIG_CLK_IMX6Q=y
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
+CONFIG_SYS_I2C_MXC=y
+CONFIG_SYS_I2C_MXC_I2C1=y
+CONFIG_SYS_I2C_MXC_I2C2=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_SUPPORT_EMMC_BOOT=y
CONFIG_FSL_USDHC=y
CONFIG_PHYLIB=y
CONFIG_PHY_ATHEROS=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_SPL_DM_REGULATOR_FIXED=y
+# CONFIG_REQUIRE_SERIAL_CONSOLE is not set
+CONFIG_MXC_UART=y
+CONFIG_SYSRESET=y
+CONFIG_SPL_SYSRESET=y
+CONFIG_SYSRESET_WATCHDOG=y
CONFIG_IMX_THERMAL=y
CONFIG_USB=y
+# CONFIG_SPL_DM_USB is not set
CONFIG_WATCHDOG_TIMEOUT_MSECS=60000
CONFIG_IMX_WATCHDOG=y
-CONFIG_OF_LIBFDT=y
#define CONFIG_SYS_MALLOC_LEN (4 * SZ_1M)
/* FEC ethernet */
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_MXC_PHYADDR 0
#define CONFIG_ARP_TIMEOUT 200UL
-/* I2C Configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_SPEED 100000
-
-/* MMC Configs */
-#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_MMC_ENV_DEV 1 /* 0 = SDHC2, 1 = SDHC4 (eMMC) */
-#define CONFIG_SUPPORT_EMMC_BOOT
-
-/* UART */
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE UART1_BASE
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
/* USB Configs */
#ifdef CONFIG_CMD_USB
projects / oweals / u-boot.git / commitdiff