bool "SH7763RDP"
select CPU_SH4
-config TARGET_SH7785LCR
- bool "SH7785LCR"
- select CPU_SH4A
-
endchoice
config SYS_ARCH
source "board/renesas/sh7753evb/Kconfig"
source "board/renesas/sh7757lcr/Kconfig"
source "board/renesas/sh7763rdp/Kconfig"
-source "board/renesas/sh7785lcr/Kconfig"
source "board/shmin/Kconfig"
endmenu
+++ /dev/null
-if TARGET_SH7785LCR
-
-config SYS_BOARD
- default "sh7785lcr"
-
-config SYS_VENDOR
- default "renesas"
-
-config SYS_CONFIG_NAME
- default "sh7785lcr"
-
-endif
+++ /dev/null
-SH7785LCR BOARD
-#M: -
-S: Maintained
-F: board/renesas/sh7785lcr/
-F: include/configs/sh7785lcr.h
-F: configs/sh7785lcr_defconfig
-F: configs/sh7785lcr_32bit_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2008 Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
-#
-
-obj-y := sh7785lcr.o selfcheck.o rtl8169_mac.o
-extra-y += lowlevel_init.o
+++ /dev/null
-========================================
-Renesas Technology R0P7785LC0011RL board
-========================================
-
-This board specification:
-=========================
-
-The R0P7785LC0011RL(board config name:sh7785lcr) has the following device:
-
- - SH7785 (SH-4A)
- - DDR2-SDRAM 512MB
- - NOR Flash 64MB
- - 2D Graphic controller
- - SATA controller
- - Ethernet controller
- - USB host/peripheral controller
- - SD controller
- - I2C controller
- - RTC
-
-This board has 2 physical memory maps. It can be changed with DIP switch(S2-5).
-
- phys address | S2-5 = OFF | S2-5 = ON
- -------------------------------+---------------+---------------
- 0x00000000 - 0x03ffffff(CS0) | NOR Flash | NOR Flash
- 0x04000000 - 0x05ffffff(CS1) | PLD | PLD
- 0x06000000 - 0x07ffffff(CS1) | reserved | I2C
- 0x08000000 - 0x0bffffff(CS2) | USB | DDR SDRAM
- 0x0c000000 - 0x0fffffff(CS3) | SD | DDR SDRAM
- 0x10000000 - 0x13ffffff(CS4) | SM107 | SM107
- 0x14000000 - 0x17ffffff(CS5) | I2C | USB
- 0x18000000 - 0x1bffffff(CS6) | reserved | SD
- 0x40000000 - 0x5fffffff | DDR SDRAM | (cannot use)
-
-
-configuration for This board:
-=============================
-
-You can choose configuration as follows:
-
- - make sh7785lcr_config
- - make sh7785lcr_32bit_config
-
-When you use "make sh7785lcr_config", there is build U-Boot for 29-bit
-address mode. This mode can use 128MB DDR-SDRAM.
-
-When you use "make sh7785lcr_32bit_config", there is build U-Boot for 32-bit
-extended address mode. This mode can use 384MB DDR-SDRAM. And if you run
-"pmb" command, this mode can use 512MB DDR-SDRAM.
-
- * 32-bit extended address mode PMB mapping *
- a) on start-up
- virt | phys | size | device
- -------------+---------------+---------------+---------------
- 0x88000000 | 0x48000000 | 384MB | DDR-SDRAM (Cacheable)
- 0xa0000000 | 0x00000000 | 64MB | NOR Flash
- 0xa4000000 | 0x04000000 | 16MB | PLD
- 0xa6000000 | 0x08000000 | 16MB | USB
- 0xa8000000 | 0x48000000 | 384MB | DDR-SDRAM (Non-cacheable)
-
- b) after "pmb" command
- virt | phys | size | device
- -------------+---------------+---------------+---------------
- 0x80000000 | 0x40000000 | 512MB | DDR-SDRAM (Cacheable)
- 0xa0000000 | 0x40000000 | 512MB | DDR-SDRAM (Non-cacheable)
-
-
-This board specific command:
-============================
-
-This board has the following its specific command:
-
- - hwtest
- - printmac
- - setmac
- - pmb (sh7785lcr_32bit_config only)
-
-
-1. hwtest
-
-This is self-check command. This command has the following options:
-
- - all : test all hardware
- - pld : output PLD version
- - led : turn on LEDs
- - dipsw : test DIP switch
- - sm107 : output SM107 version
- - net : check RTL8110 ID
- - sata : check SiI3512 ID
- - net : output PCI slot device ID
-
-i.e)
-=> hwtest led
-turn on LEDs 3, 5, 7, 9
-turn on LEDs 4, 6, 8, 10
-
-=> hwtest net
-Ethernet OK
-
-
-2. printmac
-
-This command outputs MAC address of this board.
-
-i.e)
-=> printmac
-MAC = 00:00:87:**:**:**
-
-
-3. setmac
-
-This command writes MAC address of this board.
-
-i.e)
-=> setmac 00:00:87:**:**:**
-
-
-4. pmb
-
-This command change PMB for DDR-SDRAM all mapping. However you cannot use
-NOR Flash and USB Host on U-Boot when you run this command.
-i.e)
-=> pmb
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2008 Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
- */
-#include <config.h>
-#include <asm/processor.h>
-#include <asm/macro.h>
-
-#include <asm/processor.h>
-
- .global lowlevel_init
-
- .text
- .align 2
-
-lowlevel_init:
- wait_timer WAIT_200US
- wait_timer WAIT_200US
-
- /*------- LBSC -------*/
- write32 MMSELR_A, MMSELR_D
-
- /*------- DBSC2 -------*/
- write32 DBSC2_DBCONF_A, DBSC2_DBCONF_D
- write32 DBSC2_DBTR0_A, DBSC2_DBTR0_D
- write32 DBSC2_DBTR1_A, DBSC2_DBTR1_D
- write32 DBSC2_DBTR2_A, DBSC2_DBTR2_D
- write32 DBSC2_DBFREQ_A, DBSC2_DBFREQ_D1
- write32 DBSC2_DBFREQ_A, DBSC2_DBFREQ_D2
- wait_timer WAIT_200US
-
- write32 DBSC2_DBDICODTOCD_A, DBSC2_DBDICODTOCD_D
- write32 DBSC2_DBCMDCNT_A, DBSC2_DBCMDCNT_D_CKE_H
- wait_timer WAIT_200US
- write32 DBSC2_DBCMDCNT_A, DBSC2_DBCMDCNT_D_PALL
- write32 DBSC2_DBMRCNT_A, DBSC2_DBMRCNT_D_EMRS2
- write32 DBSC2_DBMRCNT_A, DBSC2_DBMRCNT_D_EMRS3
- write32 DBSC2_DBMRCNT_A, DBSC2_DBMRCNT_D_EMRS1_1
- write32 DBSC2_DBMRCNT_A, DBSC2_DBMRCNT_D_MRS_1
- write32 DBSC2_DBCMDCNT_A, DBSC2_DBCMDCNT_D_PALL
- write32 DBSC2_DBCMDCNT_A, DBSC2_DBCMDCNT_D_REF
- write32 DBSC2_DBCMDCNT_A, DBSC2_DBCMDCNT_D_REF
- write32 DBSC2_DBMRCNT_A, DBSC2_DBMRCNT_D_MRS_2
- wait_timer WAIT_200US
-
- write32 DBSC2_DBMRCNT_A, DBSC2_DBMRCNT_D_EMRS1_2
- write32 DBSC2_DBMRCNT_A, DBSC2_DBMRCNT_D_EMRS1_1
-
- write32 DBSC2_DBEN_A, DBSC2_DBEN_D
- write32 DBSC2_DBRFCNT1_A, DBSC2_DBRFCNT1_D
- write32 DBSC2_DBRFCNT2_A, DBSC2_DBRFCNT2_D
- write32 DBSC2_DBRFCNT0_A, DBSC2_DBRFCNT0_D
- wait_timer WAIT_200US
-
- /*------- GPIO -------*/
- write16 PACR_A, PXCR_D
- write16 PBCR_A, PXCR_D
- write16 PCCR_A, PXCR_D
- write16 PDCR_A, PXCR_D
- write16 PECR_A, PXCR_D
- write16 PFCR_A, PXCR_D
- write16 PGCR_A, PXCR_D
- write16 PHCR_A, PHCR_D
- write16 PJCR_A, PJCR_D
- write16 PKCR_A, PKCR_D
- write16 PLCR_A, PXCR_D
- write16 PMCR_A, PMCR_D
- write16 PNCR_A, PNCR_D
- write16 PPCR_A, PXCR_D
- write16 PQCR_A, PXCR_D
- write16 PRCR_A, PXCR_D
-
- write8 PEPUPR_A, PEPUPR_D
- write8 PHPUPR_A, PHPUPR_D
- write8 PJPUPR_A, PJPUPR_D
- write8 PKPUPR_A, PKPUPR_D
- write8 PLPUPR_A, PLPUPR_D
- write8 PMPUPR_A, PMPUPR_D
- write8 PNPUPR_A, PNPUPR_D
- write16 PPUPR1_A, PPUPR1_D
- write16 PPUPR2_A, PPUPR2_D
- write16 P1MSELR_A, P1MSELR_D
- write16 P2MSELR_A, P2MSELR_D
-
- /*------- LBSC -------*/
- write32 BCR_A, BCR_D
- write32 CS0BCR_A, CS0BCR_D
- write32 CS0WCR_A, CS0WCR_D
- write32 CS1BCR_A, CS1BCR_D
- write32 CS1WCR_A, CS1WCR_D
- write32 CS4BCR_A, CS4BCR_D
- write32 CS4WCR_A, CS4WCR_D
-
- mov.l PASCR_A, r0
- mov.l @r0, r2
- mov.l PASCR_32BIT_MODE, r1
- tst r1, r2
- bt lbsc_29bit
-
- write32 CS2BCR_A, CS_USB_BCR_D
- write32 CS2WCR_A, CS_USB_WCR_D
- write32 CS3BCR_A, CS_SD_BCR_D
- write32 CS3WCR_A, CS_SD_WCR_D
- write32 CS5BCR_A, CS_I2C_BCR_D
- write32 CS5WCR_A, CS_I2C_WCR_D
- write32 CS6BCR_A, CS0BCR_D
- write32 CS6WCR_A, CS0WCR_D
- bra lbsc_end
- nop
-
-lbsc_29bit:
- write32 CS5BCR_A, CS_USB_BCR_D
- write32 CS5WCR_A, CS_USB_WCR_D
- write32 CS6BCR_A, CS_SD_BCR_D
- write32 CS6WCR_A, CS_SD_WCR_D
-
-lbsc_end:
-#if defined(CONFIG_SH_32BIT)
- /*------- set PMB -------*/
- write32 PASCR_A, PASCR_29BIT_D
- write32 MMUCR_A, MMUCR_D
-
- /*****************************************************************
- * ent virt phys v sz c wt
- * 0 0xa0000000 0x00000000 1 64M 0 0
- * 1 0xa4000000 0x04000000 1 16M 0 0
- * 2 0xa6000000 0x08000000 1 16M 0 0
- * 9 0x88000000 0x48000000 1 128M 1 1
- * 10 0x90000000 0x50000000 1 128M 1 1
- * 11 0x98000000 0x58000000 1 128M 1 1
- * 13 0xa8000000 0x48000000 1 128M 0 0
- * 14 0xb0000000 0x50000000 1 128M 0 0
- * 15 0xb8000000 0x58000000 1 128M 0 0
- */
- write32 PMB_ADDR_FLASH_A, PMB_ADDR_FLASH_D
- write32 PMB_DATA_FLASH_A, PMB_DATA_FLASH_D
- write32 PMB_ADDR_CPLD_A, PMB_ADDR_CPLD_D
- write32 PMB_DATA_CPLD_A, PMB_DATA_CPLD_D
- write32 PMB_ADDR_USB_A, PMB_ADDR_USB_D
- write32 PMB_DATA_USB_A, PMB_DATA_USB_D
- write32 PMB_ADDR_DDR_C1_A, PMB_ADDR_DDR_C1_D
- write32 PMB_DATA_DDR_C1_A, PMB_DATA_DDR_C1_D
- write32 PMB_ADDR_DDR_C2_A, PMB_ADDR_DDR_C2_D
- write32 PMB_DATA_DDR_C2_A, PMB_DATA_DDR_C2_D
- write32 PMB_ADDR_DDR_C3_A, PMB_ADDR_DDR_C3_D
- write32 PMB_DATA_DDR_C3_A, PMB_DATA_DDR_C3_D
- write32 PMB_ADDR_DDR_N1_A, PMB_ADDR_DDR_N1_D
- write32 PMB_DATA_DDR_N1_A, PMB_DATA_DDR_N1_D
- write32 PMB_ADDR_DDR_N2_A, PMB_ADDR_DDR_N2_D
- write32 PMB_DATA_DDR_N2_A, PMB_DATA_DDR_N2_D
- write32 PMB_ADDR_DDR_N3_A, PMB_ADDR_DDR_N3_D
- write32 PMB_DATA_DDR_N3_A, PMB_DATA_DDR_N3_D
-
- write32 PASCR_A, PASCR_INIT
- mov.l DUMMY_ADDR, r0
- icbi @r0
-#endif
-
- write32 CCR_A, CCR_D
-
- rts
- nop
-
- .align 4
-
-/*------- GPIO -------*/
-/* P{A,B C,D,E,F,G,L,P,Q,R}CR_D */
-PXCR_D: .word 0x0000
-
-PHCR_D: .word 0x00c0
-PJCR_D: .word 0xc3fc
-PKCR_D: .word 0x03ff
-PMCR_D: .word 0xffff
-PNCR_D: .word 0xf0c3
-
-PEPUPR_D: .long 0xff
-PHPUPR_D: .long 0x00
-PJPUPR_D: .long 0x00
-PKPUPR_D: .long 0x00
-PLPUPR_D: .long 0x00
-PMPUPR_D: .long 0xfc
-PNPUPR_D: .long 0x00
-PPUPR1_D: .word 0xffbf
-PPUPR2_D: .word 0xff00
-P1MSELR_D: .word 0x3780
-P2MSELR_D: .word 0x0000
-
-#define GPIO_BASE 0xffe70000
-PACR_A: .long GPIO_BASE + 0x00
-PBCR_A: .long GPIO_BASE + 0x02
-PCCR_A: .long GPIO_BASE + 0x04
-PDCR_A: .long GPIO_BASE + 0x06
-PECR_A: .long GPIO_BASE + 0x08
-PFCR_A: .long GPIO_BASE + 0x0a
-PGCR_A: .long GPIO_BASE + 0x0c
-PHCR_A: .long GPIO_BASE + 0x0e
-PJCR_A: .long GPIO_BASE + 0x10
-PKCR_A: .long GPIO_BASE + 0x12
-PLCR_A: .long GPIO_BASE + 0x14
-PMCR_A: .long GPIO_BASE + 0x16
-PNCR_A: .long GPIO_BASE + 0x18
-PPCR_A: .long GPIO_BASE + 0x1a
-PQCR_A: .long GPIO_BASE + 0x1c
-PRCR_A: .long GPIO_BASE + 0x1e
-PEPUPR_A: .long GPIO_BASE + 0x48
-PHPUPR_A: .long GPIO_BASE + 0x4e
-PJPUPR_A: .long GPIO_BASE + 0x50
-PKPUPR_A: .long GPIO_BASE + 0x52
-PLPUPR_A: .long GPIO_BASE + 0x54
-PMPUPR_A: .long GPIO_BASE + 0x56
-PNPUPR_A: .long GPIO_BASE + 0x58
-PPUPR1_A: .long GPIO_BASE + 0x60
-PPUPR2_A: .long GPIO_BASE + 0x62
-P1MSELR_A: .long GPIO_BASE + 0x80
-P2MSELR_A: .long GPIO_BASE + 0x82
-
-MMSELR_A: .long 0xfc400020
-#if defined(CONFIG_SH_32BIT)
-MMSELR_D: .long 0xa5a50005
-#else
-MMSELR_D: .long 0xa5a50002
-#endif
-
-/*------- DBSC2 -------*/
-#define DBSC2_BASE 0xfe800000
-DBSC2_DBSTATE_A: .long DBSC2_BASE + 0x0c
-DBSC2_DBEN_A: .long DBSC2_BASE + 0x10
-DBSC2_DBCMDCNT_A: .long DBSC2_BASE + 0x14
-DBSC2_DBCONF_A: .long DBSC2_BASE + 0x20
-DBSC2_DBTR0_A: .long DBSC2_BASE + 0x30
-DBSC2_DBTR1_A: .long DBSC2_BASE + 0x34
-DBSC2_DBTR2_A: .long DBSC2_BASE + 0x38
-DBSC2_DBRFCNT0_A: .long DBSC2_BASE + 0x40
-DBSC2_DBRFCNT1_A: .long DBSC2_BASE + 0x44
-DBSC2_DBRFCNT2_A: .long DBSC2_BASE + 0x48
-DBSC2_DBRFSTS_A: .long DBSC2_BASE + 0x4c
-DBSC2_DBFREQ_A: .long DBSC2_BASE + 0x50
-DBSC2_DBDICODTOCD_A:.long DBSC2_BASE + 0x54
-DBSC2_DBMRCNT_A: .long DBSC2_BASE + 0x60
-DDR_DUMMY_ACCESS_A: .long 0x40000000
-
-DBSC2_DBCONF_D: .long 0x00630002
-DBSC2_DBTR0_D: .long 0x050b1f04
-DBSC2_DBTR1_D: .long 0x00040204
-DBSC2_DBTR2_D: .long 0x02100308
-DBSC2_DBFREQ_D1: .long 0x00000000
-DBSC2_DBFREQ_D2: .long 0x00000100
-DBSC2_DBDICODTOCD_D:.long 0x000f0907
-
-DBSC2_DBCMDCNT_D_CKE_H: .long 0x00000003
-DBSC2_DBCMDCNT_D_PALL: .long 0x00000002
-DBSC2_DBCMDCNT_D_REF: .long 0x00000004
-
-DBSC2_DBMRCNT_D_EMRS2: .long 0x00020000
-DBSC2_DBMRCNT_D_EMRS3: .long 0x00030000
-DBSC2_DBMRCNT_D_EMRS1_1: .long 0x00010006
-DBSC2_DBMRCNT_D_EMRS1_2: .long 0x00010386
-DBSC2_DBMRCNT_D_MRS_1: .long 0x00000952
-DBSC2_DBMRCNT_D_MRS_2: .long 0x00000852
-
-DBSC2_DBEN_D: .long 0x00000001
-
-DBSC2_DBPDCNT0_D3: .long 0x00000080
-DBSC2_DBRFCNT1_D: .long 0x00000926
-DBSC2_DBRFCNT2_D: .long 0x00fe00fe
-DBSC2_DBRFCNT0_D: .long 0x00010000
-
-WAIT_200US: .long 33333
-
-/*------- LBSC -------*/
-PASCR_A: .long 0xff000070
-PASCR_32BIT_MODE: .long 0x80000000 /* check booting mode */
-
-BCR_A: .long BCR
-CS0BCR_A: .long CS0BCR
-CS0WCR_A: .long CS0WCR
-CS1BCR_A: .long CS1BCR
-CS1WCR_A: .long CS1WCR
-CS2BCR_A: .long CS2BCR
-CS2WCR_A: .long CS2WCR
-CS3BCR_A: .long CS3BCR
-CS3WCR_A: .long CS3WCR
-CS4BCR_A: .long CS4BCR
-CS4WCR_A: .long CS4WCR
-CS5BCR_A: .long CS5BCR
-CS5WCR_A: .long CS5WCR
-CS6BCR_A: .long CS6BCR
-CS6WCR_A: .long CS6WCR
-
-BCR_D: .long 0x80000003
-CS0BCR_D: .long 0x22222340
-CS0WCR_D: .long 0x00111118
-CS1BCR_D: .long 0x11111100
-CS1WCR_D: .long 0x33333303
-CS4BCR_D: .long 0x11111300
-CS4WCR_D: .long 0x00101012
-
-/* USB setting : 32bit mode = CS2, 29bit mode = CS5 */
-CS_USB_BCR_D: .long 0x11111200
-CS_USB_WCR_D: .long 0x00020005
-
-/* SD setting : 32bit mode = CS3, 29bit mode = CS6 */
-CS_SD_BCR_D: .long 0x00000300
-CS_SD_WCR_D: .long 0x00030108
-
-/* I2C setting : 32bit mode = CS5, 29bit mode = CS1(already setting) */
-CS_I2C_BCR_D: .long 0x11111100
-CS_I2C_WCR_D: .long 0x00000003
-
-#if defined(CONFIG_SH_32BIT)
-/*------- set PMB -------*/
-PMB_ADDR_FLASH_A: .long PMB_ADDR_BASE(0)
-PMB_ADDR_CPLD_A: .long PMB_ADDR_BASE(1)
-PMB_ADDR_USB_A: .long PMB_ADDR_BASE(2)
-PMB_ADDR_DDR_C1_A: .long PMB_ADDR_BASE(9)
-PMB_ADDR_DDR_C2_A: .long PMB_ADDR_BASE(10)
-PMB_ADDR_DDR_C3_A: .long PMB_ADDR_BASE(11)
-PMB_ADDR_DDR_N1_A: .long PMB_ADDR_BASE(13)
-PMB_ADDR_DDR_N2_A: .long PMB_ADDR_BASE(14)
-PMB_ADDR_DDR_N3_A: .long PMB_ADDR_BASE(15)
-
-PMB_ADDR_FLASH_D: .long mk_pmb_addr_val(0xa0)
-PMB_ADDR_CPLD_D: .long mk_pmb_addr_val(0xa4)
-PMB_ADDR_USB_D: .long mk_pmb_addr_val(0xa6)
-PMB_ADDR_DDR_C1_D: .long mk_pmb_addr_val(0x88)
-PMB_ADDR_DDR_C2_D: .long mk_pmb_addr_val(0x90)
-PMB_ADDR_DDR_C3_D: .long mk_pmb_addr_val(0x98)
-PMB_ADDR_DDR_N1_D: .long mk_pmb_addr_val(0xa8)
-PMB_ADDR_DDR_N2_D: .long mk_pmb_addr_val(0xb0)
-PMB_ADDR_DDR_N3_D: .long mk_pmb_addr_val(0xb8)
-
-PMB_DATA_FLASH_A: .long PMB_DATA_BASE(0)
-PMB_DATA_CPLD_A: .long PMB_DATA_BASE(1)
-PMB_DATA_USB_A: .long PMB_DATA_BASE(2)
-PMB_DATA_DDR_C1_A: .long PMB_DATA_BASE(9)
-PMB_DATA_DDR_C2_A: .long PMB_DATA_BASE(10)
-PMB_DATA_DDR_C3_A: .long PMB_DATA_BASE(11)
-PMB_DATA_DDR_N1_A: .long PMB_DATA_BASE(13)
-PMB_DATA_DDR_N2_A: .long PMB_DATA_BASE(14)
-PMB_DATA_DDR_N3_A: .long PMB_DATA_BASE(15)
-
-/* ppn ub v s1 s0 c wt */
-PMB_DATA_FLASH_D: .long mk_pmb_data_val(0x00, 1, 1, 0, 1, 0, 1)
-PMB_DATA_CPLD_D: .long mk_pmb_data_val(0x04, 1, 1, 0, 0, 0, 1)
-PMB_DATA_USB_D: .long mk_pmb_data_val(0x08, 1, 1, 0, 0, 0, 1)
-PMB_DATA_DDR_C1_D: .long mk_pmb_data_val(0x48, 0, 1, 1, 0, 1, 1)
-PMB_DATA_DDR_C2_D: .long mk_pmb_data_val(0x50, 0, 1, 1, 0, 1, 1)
-PMB_DATA_DDR_C3_D: .long mk_pmb_data_val(0x58, 0, 1, 1, 0, 1, 1)
-PMB_DATA_DDR_N1_D: .long mk_pmb_data_val(0x48, 1, 1, 1, 0, 0, 1)
-PMB_DATA_DDR_N2_D: .long mk_pmb_data_val(0x50, 1, 1, 1, 0, 0, 1)
-PMB_DATA_DDR_N3_D: .long mk_pmb_data_val(0x58, 1, 1, 1, 0, 0, 1)
-
-DUMMY_ADDR: .long 0xa0000000
-PASCR_29BIT_D: .long 0x00000000
-PASCR_INIT: .long 0x80000080 /* check booting mode */
-MMUCR_A: .long 0xff000010
-MMUCR_D: .long 0x00000004 /* clear ITLB */
-#endif /* CONFIG_SH_32BIT */
-
-CCR_A: .long 0xff00001c
-CCR_D: .long 0x0000090b
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2008 Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
- */
-
-#define PCIREG_8(_adr) (*(volatile unsigned char *)(_adr))
-#define PCIREG_32(_adr) (*(volatile unsigned long *)(_adr))
-#define PCI_PAR PCIREG_32(0xfe0401c0)
-#define PCI_PDR PCIREG_32(0xfe040220)
-#define PCI_CR PCIREG_32(0xfe040100)
-#define PCI_CONF1 PCIREG_32(0xfe040004)
-
-#define HIGH 1
-#define LOW 0
-
-#define PCI_PROG 0x80
-#define PCI_EEP_ADDRESS (unsigned short)0x0007
-#define PCI_MAC_ADDRESS_SIZE 3
-
-#define TIME1 100
-#define TIME2 20000
-
-#define BIT_DUMMY 0
-#define MAC_EEP_READ 1
-#define MAC_EEP_WRITE 2
-#define MAC_EEP_ERACE 3
-#define MAC_EEP_EWEN 4
-#define MAC_EEP_EWDS 5
-
-/* RTL8169 */
-const unsigned short EEPROM_W_Data_8169_A[] = {
- 0x8129, 0x10ec, 0x8169, 0x1154, 0x032b,
- 0x4020, 0xa101
-};
-const unsigned short EEPROM_W_Data_8169_B[] = {
- 0x4d15, 0xf7c2, 0x8000, 0x0000, 0x0000, 0x1300,
- 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
- 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x2000,
- 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
- 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
- 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
- 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2008 Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
- */
-
-#include <common.h>
-#include "rtl8169.h"
-
-static unsigned char *PCI_MEMR;
-
-static void mac_delay(unsigned int cnt)
-{
- udelay(cnt);
-}
-
-static void mac_pci_setup(void)
-{
- unsigned long pci_data;
-
- PCI_PAR = 0x00000010;
- PCI_PDR = 0x00001000;
- PCI_PAR = 0x00000004;
- pci_data = PCI_PDR;
- PCI_PDR = pci_data | 0x00000007;
- PCI_PAR = 0x00000010;
-
- PCI_MEMR = (unsigned char *)((PCI_PDR | 0xFE240050) & 0xFFFFFFF0);
-}
-
-static void EECS(int level)
-{
- unsigned char data = *PCI_MEMR;
-
- if (level)
- *PCI_MEMR = data | 0x08;
- else
- *PCI_MEMR = data & 0xf7;
-}
-
-static void EECLK(int level)
-{
- unsigned char data = *PCI_MEMR;
-
- if (level)
- *PCI_MEMR = data | 0x04;
- else
- *PCI_MEMR = data & 0xfb;
-}
-
-static void EEDI(int level)
-{
- unsigned char data = *PCI_MEMR;
-
- if (level)
- *PCI_MEMR = data | 0x02;
- else
- *PCI_MEMR = data & 0xfd;
-}
-
-static inline void sh7785lcr_bitset(unsigned short bit)
-{
- if (bit)
- EEDI(HIGH);
- else
- EEDI(LOW);
-
- EECLK(LOW);
- mac_delay(TIME1);
- EECLK(HIGH);
- mac_delay(TIME1);
- EEDI(LOW);
-}
-
-static inline unsigned char sh7785lcr_bitget(void)
-{
- unsigned char bit;
-
- EECLK(LOW);
- mac_delay(TIME1);
- bit = *PCI_MEMR & 0x01;
- EECLK(HIGH);
- mac_delay(TIME1);
-
- return bit;
-}
-
-static inline void sh7785lcr_setcmd(unsigned char command)
-{
- sh7785lcr_bitset(BIT_DUMMY);
- switch (command) {
- case MAC_EEP_READ:
- sh7785lcr_bitset(1);
- sh7785lcr_bitset(1);
- sh7785lcr_bitset(0);
- break;
- case MAC_EEP_WRITE:
- sh7785lcr_bitset(1);
- sh7785lcr_bitset(0);
- sh7785lcr_bitset(1);
- break;
- case MAC_EEP_ERACE:
- sh7785lcr_bitset(1);
- sh7785lcr_bitset(1);
- sh7785lcr_bitset(1);
- break;
- case MAC_EEP_EWEN:
- sh7785lcr_bitset(1);
- sh7785lcr_bitset(0);
- sh7785lcr_bitset(0);
- break;
- case MAC_EEP_EWDS:
- sh7785lcr_bitset(1);
- sh7785lcr_bitset(0);
- sh7785lcr_bitset(0);
- break;
- default:
- break;
- }
-}
-
-static inline unsigned short sh7785lcr_getdt(void)
-{
- unsigned short data = 0;
- int i;
-
- sh7785lcr_bitget(); /* DUMMY */
- for (i = 0 ; i < 16 ; i++) {
- data <<= 1;
- data |= sh7785lcr_bitget();
- }
- return data;
-}
-
-static inline void sh7785lcr_setadd(unsigned short address)
-{
- sh7785lcr_bitset(address & 0x0020); /* A5 */
- sh7785lcr_bitset(address & 0x0010); /* A4 */
- sh7785lcr_bitset(address & 0x0008); /* A3 */
- sh7785lcr_bitset(address & 0x0004); /* A2 */
- sh7785lcr_bitset(address & 0x0002); /* A1 */
- sh7785lcr_bitset(address & 0x0001); /* A0 */
-}
-
-static inline void sh7785lcr_setdata(unsigned short data)
-{
- sh7785lcr_bitset(data & 0x8000);
- sh7785lcr_bitset(data & 0x4000);
- sh7785lcr_bitset(data & 0x2000);
- sh7785lcr_bitset(data & 0x1000);
- sh7785lcr_bitset(data & 0x0800);
- sh7785lcr_bitset(data & 0x0400);
- sh7785lcr_bitset(data & 0x0200);
- sh7785lcr_bitset(data & 0x0100);
- sh7785lcr_bitset(data & 0x0080);
- sh7785lcr_bitset(data & 0x0040);
- sh7785lcr_bitset(data & 0x0020);
- sh7785lcr_bitset(data & 0x0010);
- sh7785lcr_bitset(data & 0x0008);
- sh7785lcr_bitset(data & 0x0004);
- sh7785lcr_bitset(data & 0x0002);
- sh7785lcr_bitset(data & 0x0001);
-}
-
-static void sh7785lcr_datawrite(const unsigned short *data, unsigned short address,
- unsigned int count)
-{
- unsigned int i;
-
- for (i = 0; i < count; i++) {
- EECS(HIGH);
- EEDI(LOW);
- mac_delay(TIME1);
-
- sh7785lcr_setcmd(MAC_EEP_WRITE);
- sh7785lcr_setadd(address++);
- sh7785lcr_setdata(*(data + i));
-
- EECLK(LOW);
- EEDI(LOW);
- EECS(LOW);
- mac_delay(TIME2);
- }
-}
-
-static void sh7785lcr_macerase(void)
-{
- unsigned int i;
- unsigned short pci_address = 7;
-
- for (i = 0; i < 3; i++) {
- EECS(HIGH);
- EEDI(LOW);
- mac_delay(TIME1);
- sh7785lcr_setcmd(MAC_EEP_ERACE);
- sh7785lcr_setadd(pci_address++);
- mac_delay(TIME1);
- EECLK(LOW);
- EEDI(LOW);
- EECS(LOW);
- }
-
- mac_delay(TIME2);
-
- printf("\n\nErace End\n");
- for (i = 0; i < 10; i++)
- mac_delay(TIME2);
-}
-
-static void sh7785lcr_macwrite(unsigned short *data)
-{
- sh7785lcr_macerase();
-
- sh7785lcr_datawrite(EEPROM_W_Data_8169_A, 0x0000, 7);
- sh7785lcr_datawrite(data, PCI_EEP_ADDRESS, PCI_MAC_ADDRESS_SIZE);
- sh7785lcr_datawrite(EEPROM_W_Data_8169_B, 0x000a, 54);
-}
-
-void sh7785lcr_macdtrd(unsigned char *buf, unsigned short address, unsigned int count)
-{
- unsigned int i;
- unsigned short wk;
-
- for (i = 0 ; i < count; i++) {
- EECS(HIGH);
- EEDI(LOW);
- mac_delay(TIME1);
- sh7785lcr_setcmd(MAC_EEP_READ);
- sh7785lcr_setadd(address++);
- wk = sh7785lcr_getdt();
-
- *buf++ = (unsigned char)(wk & 0xff);
- *buf++ = (unsigned char)((wk >> 8) & 0xff);
- EECLK(LOW);
- EEDI(LOW);
- EECS(LOW);
- }
-}
-
-static void sh7785lcr_macadrd(unsigned char *buf)
-{
- *PCI_MEMR = PCI_PROG;
-
- sh7785lcr_macdtrd(buf, PCI_EEP_ADDRESS, PCI_MAC_ADDRESS_SIZE);
-}
-
-static void sh7785lcr_eepewen(void)
-{
- *PCI_MEMR = PCI_PROG;
- mac_delay(TIME1);
- EECS(LOW);
- EECLK(LOW);
- EEDI(LOW);
- EECS(HIGH);
- mac_delay(TIME1);
-
- sh7785lcr_setcmd(MAC_EEP_EWEN);
- sh7785lcr_bitset(1);
- sh7785lcr_bitset(1);
- sh7785lcr_bitset(BIT_DUMMY);
- sh7785lcr_bitset(BIT_DUMMY);
- sh7785lcr_bitset(BIT_DUMMY);
- sh7785lcr_bitset(BIT_DUMMY);
-
- EECLK(LOW);
- EEDI(LOW);
- EECS(LOW);
- mac_delay(TIME1);
-}
-
-void mac_write(unsigned short *data)
-{
- mac_pci_setup();
- sh7785lcr_eepewen();
- sh7785lcr_macwrite(data);
-}
-
-void mac_read(void)
-{
- unsigned char data[6];
-
- mac_pci_setup();
- sh7785lcr_macadrd(data);
- printf("Mac = %02x:%02x:%02x:%02x:%02x:%02x\n",
- data[0], data[1], data[2], data[3], data[4], data[5]);
-}
-
-int do_set_mac(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- int i;
- unsigned char mac[6];
- char *s, *e;
-
- if (argc != 2)
- return cmd_usage(cmdtp);
-
- s = argv[1];
-
- for (i = 0; i < 6; i++) {
- mac[i] = s ? simple_strtoul(s, &e, 16) : 0;
- if (s)
- s = (*e) ? e + 1 : e;
- }
- mac_write((unsigned short *)mac);
-
- return 0;
-}
-
-U_BOOT_CMD(
- setmac, 2, 1, do_set_mac,
- "write MAC address for RTL8110SCL",
- "\n"
- "setmac <mac address> - write MAC address for RTL8110SCL"
-);
-
-int do_print_mac(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- if (argc != 1)
- return cmd_usage(cmdtp);
-
- mac_read();
-
- return 0;
-}
-
-U_BOOT_CMD(
- printmac, 1, 1, do_print_mac,
- "print MAC address for RTL8110",
- "\n"
- " - print MAC address for RTL8110"
-);
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2008 Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
- */
-
-#include <common.h>
-#include <console.h>
-#include <asm/io.h>
-#include <asm/processor.h>
-#include <asm/pci.h>
-
-#if defined(CONFIG_CPU_32BIT)
-#define NOCACHE_OFFSET 0x00000000
-#else
-#define NOCACHE_OFFSET 0xa0000000
-#endif
-#define PLD_LEDCR (0x04000008 + NOCACHE_OFFSET)
-#define PLD_SWSR (0x0400000a + NOCACHE_OFFSET)
-#define PLD_VERSR (0x0400000c + NOCACHE_OFFSET)
-
-#define SM107_DEVICEID (0x13e00060 + NOCACHE_OFFSET)
-
-static void test_pld(void)
-{
- printf("PLD version = %04x\n", readb(PLD_VERSR));
-}
-
-static void test_sm107(void)
-{
- printf("SM107 device ID = %04x\n", readl(SM107_DEVICEID));
-}
-
-static void test_led(void)
-{
- printf("turn on LEDs 3, 5, 7, 9\n");
- writeb(0x55, PLD_LEDCR);
- mdelay(2000);
- printf("turn on LEDs 4, 6, 8, 10\n");
- writeb(0xaa, PLD_LEDCR);
- mdelay(2000);
- writeb(0x00, PLD_LEDCR);
-}
-
-static void test_dipsw(void)
-{
- printf("Please DIPSW set = B'0101\n");
- while (readb(PLD_SWSR) != 0x05) {
- if (ctrlc())
- return;
- }
- printf("Please DIPSW set = B'1010\n");
- while (readb(PLD_SWSR) != 0x0A) {
- if (ctrlc())
- return;
- }
- printf("DIPSW OK\n");
-}
-
-static void test_net(void)
-{
- unsigned long data;
-
- writel(0x80000000, 0xfe0401c0);
- data = readl(0xfe040220);
- if (data == 0x816910ec)
- printf("Ethernet OK\n");
- else
- printf("Ethernet NG, data = %08x\n", (unsigned int)data);
-}
-
-static void test_sata(void)
-{
- unsigned long data;
-
- writel(0x80000800, 0xfe0401c0);
- data = readl(0xfe040220);
- if (data == 0x35121095)
- printf("SATA OK\n");
- else
- printf("SATA NG, data = %08x\n", (unsigned int)data);
-}
-
-static void test_pci(void)
-{
- writel(0x80001800, 0xfe0401c0);
- printf("PCI CN1 ID = %08x\n", readl(0xfe040220));
-
- writel(0x80001000, 0xfe0401c0);
- printf("PCI CN2 ID = %08x\n", readl(0xfe040220));
-}
-
-int do_hw_test(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- char *cmd;
-
- if (argc != 2)
- return cmd_usage(cmdtp);
-
- cmd = argv[1];
- switch (cmd[0]) {
- case 'a': /* all */
- test_pld();
- test_led();
- test_dipsw();
- test_sm107();
- test_net();
- test_sata();
- test_pci();
- break;
- case 'p': /* pld or pci */
- if (cmd[1] == 'l')
- test_pld();
- else
- test_pci();
- break;
- case 'l': /* led */
- test_led();
- break;
- case 'd': /* dipsw */
- test_dipsw();
- break;
- case 's': /* sm107 or sata */
- if (cmd[1] == 'm')
- test_sm107();
- else
- test_sata();
- break;
- case 'n': /* net */
- test_net();
- break;
- default:
- return cmd_usage(cmdtp);
- }
-
- return 0;
-}
-
-U_BOOT_CMD(
- hwtest, 2, 1, do_hw_test,
- "hardware test for R0P7785LC0011RL board",
- "\n"
- "hwtest all - test all hardware\n"
- "hwtest pld - output PLD version\n"
- "hwtest led - turn on LEDs\n"
- "hwtest dipsw - test DIP switch\n"
- "hwtest sm107 - output SM107 version\n"
- "hwtest net - check RTL8110 ID\n"
- "hwtest sata - check SiI3512 ID\n"
- "hwtest pci - output PCI slot device ID"
-);
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2008 Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/processor.h>
-#include <asm/pci.h>
-#include <netdev.h>
-
-int checkboard(void)
-{
- puts("BOARD: Renesas Technology Corp. R0P7785LC0011RL\n");
- return 0;
-}
-
-int board_init(void)
-{
- return 0;
-}
-
-static struct pci_controller hose;
-void pci_init_board(void)
-{
- pci_sh7780_init(&hose);
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
-
-#if defined(CONFIG_SH_32BIT)
-int do_pmb(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- /* clear ITLB */
- writel(0x00000004, 0xff000010);
-
- /* delete PMB for peripheral */
- writel(0, PMB_ADDR_BASE(0));
- writel(0, PMB_DATA_BASE(0));
- writel(0, PMB_ADDR_BASE(1));
- writel(0, PMB_DATA_BASE(1));
- writel(0, PMB_ADDR_BASE(2));
- writel(0, PMB_DATA_BASE(2));
-
- /* add PMB for SDRAM(0x40000000 - 0x47ffffff) */
- writel(mk_pmb_addr_val(0x80), PMB_ADDR_BASE(8));
- writel(mk_pmb_data_val(0x40, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(8));
- writel(mk_pmb_addr_val(0xa0), PMB_ADDR_BASE(12));
- writel(mk_pmb_data_val(0x40, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(12));
-
- return 0;
-}
-
-U_BOOT_CMD(
- pmb, 1, 1, do_pmb,
- "pmb - PMB setting\n",
- "\n"
- " - PMB setting for all SDRAM mapping"
-);
-#endif
+++ /dev/null
-CONFIG_SH=y
-CONFIG_SYS_TEXT_BASE=0x8FF80000
-CONFIG_SH_32BIT=y
-CONFIG_TARGET_SH7785LCR=y
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttySC1,115200 root=/dev/nfs ip=dhcp"
-CONFIG_VERSION_VARIABLE=y
-# CONFIG_CMDLINE_EDITING is not set
-# CONFIG_AUTO_COMPLETE is not set
-# CONFIG_CMD_BDI is not set
-# CONFIG_CMD_CONSOLE is not set
-# CONFIG_CMD_BOOTD is not set
-# CONFIG_CMD_IMI is not set
-# CONFIG_CMD_XIMG is not set
-# CONFIG_CMD_EDITENV is not set
-# CONFIG_CMD_ENV_EXISTS is not set
-# CONFIG_CMD_LOADB is not set
-# CONFIG_CMD_LOADS is not set
-CONFIG_CMD_PCI=y
-CONFIG_CMD_SDRAM=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_ECHO is not set
-# CONFIG_CMD_ITEST is not set
-# CONFIG_CMD_SOURCE is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_PING=y
-# CONFIG_CMD_MISC is not set
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MAC_PARTITION=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_PCI=y
-CONFIG_SCIF_CONSOLE=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_USE_PRIVATE_LIBGCC=y
+++ /dev/null
-CONFIG_SH=y
-CONFIG_SYS_TEXT_BASE=0x0FF80000
-CONFIG_TARGET_SH7785LCR=y
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttySC1,115200 root=/dev/nfs ip=dhcp"
-CONFIG_VERSION_VARIABLE=y
-# CONFIG_CMDLINE_EDITING is not set
-# CONFIG_AUTO_COMPLETE is not set
-# CONFIG_CMD_BDI is not set
-# CONFIG_CMD_CONSOLE is not set
-# CONFIG_CMD_BOOTD is not set
-# CONFIG_CMD_IMI is not set
-# CONFIG_CMD_XIMG is not set
-# CONFIG_CMD_EDITENV is not set
-# CONFIG_CMD_ENV_EXISTS is not set
-# CONFIG_CMD_LOADB is not set
-# CONFIG_CMD_LOADS is not set
-CONFIG_CMD_PCI=y
-CONFIG_CMD_SDRAM=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_ECHO is not set
-# CONFIG_CMD_ITEST is not set
-# CONFIG_CMD_SOURCE is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_PING=y
-# CONFIG_CMD_MISC is not set
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MAC_PARTITION=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_PCI=y
-CONFIG_SCIF_CONSOLE=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_USE_PRIVATE_LIBGCC=y
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Configuation settings for the Renesas Technology R0P7785LC0011RL board
- *
- * Copyright (C) 2008 Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
- */
-
-#ifndef __SH7785LCR_H
-#define __SH7785LCR_H
-
-#define CONFIG_CPU_SH7785 1
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "bootdevice=0:1\0" \
- "usbload=usb reset;usbboot;usb stop;bootm\0"
-
-#define CONFIG_DISPLAY_BOARDINFO
-#undef CONFIG_SHOW_BOOT_PROGRESS
-
-/* MEMORY */
-#if defined(CONFIG_SH_32BIT)
-/* 0x40000000 - 0x47FFFFFF does not use */
-#define CONFIG_SH_SDRAM_OFFSET (0x8000000)
-#define SH7785LCR_SDRAM_PHYS_BASE (0x40000000 + CONFIG_SH_SDRAM_OFFSET)
-#define SH7785LCR_SDRAM_BASE (0x80000000 + CONFIG_SH_SDRAM_OFFSET)
-#define SH7785LCR_SDRAM_SIZE (384 * 1024 * 1024)
-#define SH7785LCR_FLASH_BASE_1 (0xa0000000)
-#define SH7785LCR_FLASH_BANK_SIZE (64 * 1024 * 1024)
-#define SH7785LCR_USB_BASE (0xa6000000)
-#else
-#define SH7785LCR_SDRAM_BASE (0x08000000)
-#define SH7785LCR_SDRAM_SIZE (128 * 1024 * 1024)
-#define SH7785LCR_FLASH_BASE_1 (0xa0000000)
-#define SH7785LCR_FLASH_BANK_SIZE (64 * 1024 * 1024)
-#define SH7785LCR_USB_BASE (0xb4000000)
-#endif
-
-#define CONFIG_SYS_PBSIZE 256
-#define CONFIG_SYS_BAUDRATE_TABLE { 115200 }
-
-/* SCIF */
-#define CONFIG_CONS_SCIF1 1
-#define CONFIG_SCIF_EXT_CLOCK 1
-
-#define CONFIG_SYS_MEMTEST_START (SH7785LCR_SDRAM_BASE)
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \
- (SH7785LCR_SDRAM_SIZE) - \
- 4 * 1024 * 1024)
-#undef CONFIG_SYS_MEMTEST_SCRATCH
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE
-
-#define CONFIG_SYS_SDRAM_BASE (SH7785LCR_SDRAM_BASE)
-#define CONFIG_SYS_SDRAM_SIZE (SH7785LCR_SDRAM_SIZE)
-#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 16 * 1024 * 1024)
-
-#define CONFIG_SYS_MONITOR_BASE (SH7785LCR_FLASH_BASE_1)
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
-#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024)
-
-/* FLASH */
-#undef CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_BASE (SH7785LCR_FLASH_BASE_1)
-#define CONFIG_SYS_MAX_FLASH_SECT 512
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE + \
- (0 * SH7785LCR_FLASH_BANK_SIZE) }
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000)
-#define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000)
-#define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000)
-
-#undef CONFIG_SYS_DIRECT_FLASH_TFTP
-
-/* R8A66597 */
-#define CONFIG_USB_R8A66597_HCD
-#define CONFIG_R8A66597_BASE_ADDR SH7785LCR_USB_BASE
-#define CONFIG_R8A66597_XTAL 0x0000 /* 12MHz */
-#define CONFIG_R8A66597_LDRV 0x8000 /* 3.3V */
-#define CONFIG_R8A66597_ENDIAN 0x0000 /* little */
-
-/* PCI Controller */
-#define CONFIG_SH4_PCI
-#define CONFIG_SH7780_PCI
-#if defined(CONFIG_SH_32BIT)
-#define CONFIG_SH7780_PCI_LSR 0x1ff00001
-#define CONFIG_SH7780_PCI_LAR 0x5f000000
-#define CONFIG_SH7780_PCI_BAR 0x5f000000
-#else
-#define CONFIG_SH7780_PCI_LSR 0x07f00001
-#define CONFIG_SH7780_PCI_LAR CONFIG_SYS_SDRAM_SIZE
-#define CONFIG_SH7780_PCI_BAR CONFIG_SYS_SDRAM_SIZE
-#endif
-#define CONFIG_PCI_SCAN_SHOW 1
-
-#define CONFIG_PCI_MEM_BUS 0xFD000000 /* Memory space base addr */
-#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE 0x01000000 /* Size of Memory window */
-
-#define CONFIG_PCI_IO_BUS 0xFE200000 /* IO space base address */
-#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE 0x00200000 /* Size of IO window */
-
-#if defined(CONFIG_SH_32BIT)
-#define CONFIG_PCI_SYS_PHYS SH7785LCR_SDRAM_PHYS_BASE
-#else
-#define CONFIG_PCI_SYS_PHYS CONFIG_SYS_SDRAM_BASE
-#endif
-#define CONFIG_PCI_SYS_BUS CONFIG_SYS_SDRAM_BASE
-#define CONFIG_PCI_SYS_SIZE CONFIG_SYS_SDRAM_SIZE
-
-/* ENV setting */
-#define CONFIG_ENV_OVERWRITE 1
-#define CONFIG_ENV_SECT_SIZE (256 * 1024)
-#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE)
-
-/* Board Clock */
-/* The SCIF used external clock. system clock only used timer. */
-#define CONFIG_SYS_CLK_FREQ 50000000
-#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ
-
-#endif /* __SH7785LCR_H */
projects / oweals / u-boot.git / commitdiff