Using the TPL method for nand boot by sram was already
supported. Here add some code for mpc85xx ifc nand boot.
- For ifc, elbc, esdhc, espi, all need the SPL without
section .resetvec.
- Use a clear function name for nand spl boot.
- Add CONFIG_SPL_DRIVERS_MISC_SUPPORT to compile the fsl_ifc.c
in spl/Makefile;
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
. = ALIGN(8);
__init_begin = .;
__init_end = .;
. = ALIGN(8);
__init_begin = .;
__init_end = .;
-/* FIXME for non-NAND SPL */
+
+/* For ifc, elbc, esdhc, espi, all need the SPL without section .resetvec */
+#ifdef CONFIG_SYS_MPC85XX_NO_RESETVEC
+ .bootpg ADDR(.text) - 0x1000 :
+ {
+ KEEP(*(.bootpg))
+ } :text = 0xffff
+#else
#if defined(CONFIG_FSL_IFC) /* Restrict bootpg at 4K boundry for IFC */
.bootpg ADDR(.text) + 0x1000 :
{
#if defined(CONFIG_FSL_IFC) /* Restrict bootpg at 4K boundry for IFC */
.bootpg ADDR(.text) + 0x1000 :
{
#else
#error unknown NAND controller
#endif
#else
#error unknown NAND controller
#endif
-#ifdef CONFIG_SYS_MPC85XX_NO_RESETVEC
- .bootpg ADDR(.text) - 0x1000 :
- {
- KEEP(*(.bootpg))
- } :text = 0xffff
-#else
.resetvec ADDR(.text) + RESET_VECTOR_OFFSET : {
KEEP(*(.resetvec))
} = 0xffff
.resetvec ADDR(.text) + RESET_VECTOR_OFFSET : {
KEEP(*(.resetvec))
} = 0xffff
CONFIG_SPL_LIBGENERIC_SUPPORT (lib/libgeneric.o)
CONFIG_SPL_POWER_SUPPORT (drivers/power/libpower.o)
CONFIG_SPL_NAND_SUPPORT (drivers/mtd/nand/libnand.o)
CONFIG_SPL_LIBGENERIC_SUPPORT (lib/libgeneric.o)
CONFIG_SPL_POWER_SUPPORT (drivers/power/libpower.o)
CONFIG_SPL_NAND_SUPPORT (drivers/mtd/nand/libnand.o)
+CONFIG_SPL_DRIVERS_MISC_SUPPORT (drivers/misc)
CONFIG_SPL_DMA_SUPPORT (drivers/dma/libdma.o)
CONFIG_SPL_POST_MEM_SUPPORT (post/drivers/memory.o)
CONFIG_SPL_NAND_LOAD (drivers/mtd/nand/nand_spl_load.o)
CONFIG_SPL_DMA_SUPPORT (drivers/dma/libdma.o)
CONFIG_SPL_POST_MEM_SUPPORT (post/drivers/memory.o)
CONFIG_SPL_NAND_LOAD (drivers/mtd/nand/nand_spl_load.o)
return __raw_readw((u16 *)marker) != 0xffff;
}
return __raw_readw((u16 *)marker) != 0xffff;
}
-static void nand_load(unsigned int offs, int uboot_size, uchar *dst)
+#ifdef CONFIG_TPL_BUILD
+int nand_spl_load_image(uint32_t offs, unsigned int uboot_size, void *vdst)
+#else
+static int nand_load(uint32_t offs, unsigned int uboot_size, void *vdst)
+#endif
{
struct fsl_ifc *ifc = IFC_BASE_ADDR;
uchar *buf = (uchar *)CONFIG_SYS_NAND_BASE;
{
struct fsl_ifc *ifc = IFC_BASE_ADDR;
uchar *buf = (uchar *)CONFIG_SYS_NAND_BASE;
int sram_addr;
int pg_no;
int sram_addr;
int pg_no;
/* Get NAND Flash configuration */
csor = CONFIG_SYS_NAND_CSOR;
/* Get NAND Flash configuration */
csor = CONFIG_SYS_NAND_CSOR;
offs += page_size;
} while ((offs & (blk_size - 1)) && (pos < uboot_size));
}
offs += page_size;
} while ((offs & (blk_size - 1)) && (pos < uboot_size));
}
+/*
+ * Defines a static function nand_load_image() here, because non-static makes
+ * the code too large for certain SPLs(minimal SPL, maximum size <= 4Kbytes)
+ */
+#ifndef CONFIG_TPL_BUILD
+#define nand_spl_load_image(offs, uboot_size, vdst) \
+ nand_load(offs, uboot_size, vdst)
+#endif
+
/*
* Main entrypoint for NAND Boot. It's necessary that SDRAM is already
* configured and available since this code loads the main U-boot image
/*
* Main entrypoint for NAND Boot. It's necessary that SDRAM is already
* configured and available since this code loads the main U-boot image
/*
* Load U-Boot image from NAND into RAM
*/
/*
* Load U-Boot image from NAND into RAM
*/
- nand_load(CONFIG_SYS_NAND_U_BOOT_OFFS, CONFIG_SYS_NAND_U_BOOT_SIZE,
- (uchar *)CONFIG_SYS_NAND_U_BOOT_DST);
+ nand_spl_load_image(CONFIG_SYS_NAND_U_BOOT_OFFS,
+ CONFIG_SYS_NAND_U_BOOT_SIZE,
+ (uchar *)CONFIG_SYS_NAND_U_BOOT_DST);
#ifdef CONFIG_NAND_ENV_DST
#ifdef CONFIG_NAND_ENV_DST
- nand_load(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)CONFIG_NAND_ENV_DST);
+ nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_NAND_ENV_DST);
#ifdef CONFIG_ENV_OFFSET_REDUND
#ifdef CONFIG_ENV_OFFSET_REDUND
- nand_load(CONFIG_ENV_OFFSET_REDUND, CONFIG_ENV_SIZE,
- (uchar *)CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE);
+ nand_spl_load_image(CONFIG_ENV_OFFSET_REDUND, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE);
LIBS-$(CONFIG_SPL_POWER_SUPPORT) += drivers/power/ \
drivers/power/pmic/
LIBS-$(if $(CONFIG_CMD_NAND),$(CONFIG_SPL_NAND_SUPPORT)) += drivers/mtd/nand/
LIBS-$(CONFIG_SPL_POWER_SUPPORT) += drivers/power/ \
drivers/power/pmic/
LIBS-$(if $(CONFIG_CMD_NAND),$(CONFIG_SPL_NAND_SUPPORT)) += drivers/mtd/nand/
+LIBS-$(CONFIG_SPL_DRIVERS_MISC_SUPPORT) += drivers/misc/
LIBS-$(CONFIG_SPL_ONENAND_SUPPORT) += drivers/mtd/onenand/
LIBS-$(CONFIG_SPL_DMA_SUPPORT) += drivers/dma/
LIBS-$(CONFIG_SPL_POST_MEM_SUPPORT) += post/drivers/
LIBS-$(CONFIG_SPL_ONENAND_SUPPORT) += drivers/mtd/onenand/
LIBS-$(CONFIG_SPL_DMA_SUPPORT) += drivers/dma/
LIBS-$(CONFIG_SPL_POST_MEM_SUPPORT) += post/drivers/