X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=lib%2FKconfig;h=3da45a5ec3221f8ea80091e06d21a9723b45cf02;hb=039c031e080c5b127c036a5db73e1ba91f5c0ed1;hp=b711d62d32fb8f8cb53d1113419931917d5b3e6c;hpb=6307896c177e3afb54a42439062dce0776d31891;p=oweals%2Fu-boot.git

diff --git a/lib/Kconfig b/lib/Kconfig
index b711d62d32..3da45a5ec3 100644
--- a/lib/Kconfig
+++ b/lib/Kconfig
@@ -21,6 +21,12 @@ config DYNAMIC_CRC_TABLE
 	  Enable this option to calculate entries for CRC tables at runtime.
 	  This can be helpful when reducing the size of the build image
 
+config HAVE_ARCH_IOMAP
+	bool
+	help
+	  Enable this option if architecture provides io{read,write}{8,16,32}
+	  I/O accessor functions.
+
 config HAVE_PRIVATE_LIBGCC
 	bool
 
@@ -91,6 +97,8 @@ config SYS_HZ
 
 config USE_TINY_PRINTF
 	bool "Enable tiny printf() version"
+	depends on SPL || TPL
+	default y
 	help
 	  This option enables a tiny, stripped down printf version.
 	  This should only be used in space limited environments,
@@ -141,7 +149,7 @@ config SPL_TINY_MEMSET
 	  The faster memset() is the arch-specific one (if available) enabled
 	  by CONFIG_USE_ARCH_MEMSET. If that is not enabled, we can still get
 	  better performance by writing a word at a time. But in very
-	  size-constrained envrionments even this may be too big. Enable this
+	  size-constrained environments even this may be too big. Enable this
 	  option to reduce code size slightly at the cost of some speed.
 
 config TPL_TINY_MEMSET
@@ -150,7 +158,7 @@ config TPL_TINY_MEMSET
 	  The faster memset() is the arch-specific one (if available) enabled
 	  by CONFIG_USE_ARCH_MEMSET. If that is not enabled, we can still get
 	  better performance by writing a word at a time. But in very
-	  size-constrained envrionments even this may be too big. Enable this
+	  size-constrained environments even this may be too big. Enable this
 	  option to reduce code size slightly at the cost of some speed.
 
 config RBTREE
@@ -159,6 +167,78 @@ config RBTREE
 config BITREVERSE
 	bool "Bit reverse library from Linux"
 
+config TRACE
+	bool "Support for tracing of function calls and timing"
+	imply CMD_TRACE
+	help
+	  Enables function tracing within U-Boot. This allows recording of call
+	  traces including timing information. The command can write data to
+	  memory for exporting for analysis (e.g. using bootchart).
+	  See doc/README.trace for full details.
+
+config TRACE_BUFFER_SIZE
+	hex "Size of trace buffer in U-Boot"
+	depends on TRACE
+	default 0x01000000
+	help
+	  Sets the size of the trace buffer in U-Boot. This is allocated from
+	  memory during relocation. If this buffer is too small, the trace
+	  history will be truncated, with later records omitted.
+
+	  If early trace is enabled (i.e. before relocation), this buffer must
+	  be large enough to include all the data from the early trace buffer as
+	  well, since this is copied over to the main buffer during relocation.
+
+	  A trace record is emitted for each function call and each record is
+	  12 bytes (see struct trace_call). A suggested minimum size is 1MB. If
+	  the size is too small then 'trace stats' will show a message saying
+	  how many records were dropped due to buffer overflow.
+
+config TRACE_CALL_DEPTH_LIMIT
+	int "Trace call depth limit"
+	depends on TRACE
+	default 15
+	help
+	  Sets the maximum call depth up to which function calls are recorded.
+
+config TRACE_EARLY
+	bool "Enable tracing before relocation"
+	depends on TRACE
+	help
+	  Sometimes it is helpful to trace execution of U-Boot before
+	  relocation. This is possible by using a arch-specific, fixed buffer
+	  position in memory. Enable this option to start tracing as early as
+	  possible after U-Boot starts.
+
+config TRACE_EARLY_SIZE
+	hex "Size of early trace buffer in U-Boot"
+	depends on TRACE_EARLY
+	default 0x00100000
+	help
+	  Sets the size of the early trace buffer in bytes. This is used to hold
+	  tracing information before relocation.
+
+config TRACE_EARLY_CALL_DEPTH_LIMIT
+	int "Early trace call depth limit"
+	depends on TRACE_EARLY
+	default 200
+	help
+	  Sets the maximum call depth up to which function calls are recorded
+	  during early tracing.
+
+config TRACE_EARLY_ADDR
+	hex "Address of early trace buffer in U-Boot"
+	depends on TRACE_EARLY
+	default 0x00100000
+	help
+	  Sets the address of the early trace buffer in U-Boot. This memory
+	  must be accessible before relocation.
+
+	  A trace record is emitted for each function call and each record is
+	  12 bytes (see struct trace_call). A suggested minimum size is 1MB. If
+	  the size is too small then the message which says the amount of early
+	  data being coped will the the same as the
+
 source lib/dhry/Kconfig
 
 menu "Security support"
@@ -264,6 +344,9 @@ config MD5
 config CRC32C
 	bool
 
+config XXHASH
+	bool
+
 endmenu
 
 menu "Compression Support"
@@ -295,6 +378,33 @@ config LZO
 	help
 	  This enables support for LZO compression algorithm.r
 
+config GZIP
+	bool "Enable gzip decompression support"
+	select ZLIB
+	default y
+	help
+	  This enables support for GZIP compression algorithm.
+
+config ZLIB
+	bool
+	default y
+	help
+	  This enables ZLIB compression lib.
+
+config ZSTD
+	bool "Enable Zstandard decompression support"
+	select XXHASH
+	help
+	  This enables Zstandard decompression library.
+
+config SPL_LZ4
+	bool "Enable LZ4 decompression support in SPL"
+	help
+	  This enables support for tge LZ4 decompression algorithm in SPL. LZ4
+	  is a lossless data compression algorithm that is focused on
+	  fast compression and decompression speed. It belongs to the LZ77
+	  family of byte-oriented compression schemes.
+
 config SPL_LZO
 	bool "Enable LZO decompression support in SPL"
 	help
@@ -311,6 +421,12 @@ config SPL_ZLIB
 	help
 	  This enables compression lib for SPL boot.
 
+config SPL_ZSTD
+	bool "Enable Zstandard decompression support in SPL"
+	select XXHASH
+	help
+	  This enables Zstandard decompression library in the SPL.
+
 endmenu
 
 config ERRNO_STR
@@ -353,6 +469,16 @@ config SPL_OF_LIBFDT
 	  particular compatible nodes. The library operates on a flattened
 	  version of the device tree.
 
+config TPL_OF_LIBFDT
+	bool "Enable the FDT library for TPL"
+	default y if TPL_OF_CONTROL
+	help
+	  This enables the FDT library (libfdt). It provides functions for
+	  accessing binary device tree images in memory, such as adding and
+	  removing nodes and properties, scanning through the tree and finding
+	  particular compatible nodes. The library operates on a flattened
+	  version of the device tree.
+
 config FDT_FIXUP_PARTITIONS
 	bool "overwrite MTD partitions in DTS through defined in 'mtdparts'"
 	depends on OF_LIBFDT
@@ -399,4 +525,8 @@ source lib/efi/Kconfig
 source lib/efi_loader/Kconfig
 source lib/optee/Kconfig
 
+config TEST_FDTDEC
+	bool "enable fdtdec test"
+	depends on OF_LIBFDT
+
 endmenu